माइक्रोकंट्रोलर्स

उत्पाद (20,000+)

PIC16F19155-I/SS - 14KB Flash 32MHz XLP MCU | Microchip
PIC16F19155-I/SS

PIC16F19155-I/SS - 14KB Flash 32MHz XLP MCU | Microchip

The Microchip Technology PIC16F19155-I/SS is an 8-bit PIC16 RISC microcontroller with 14KB (8K x 14) of Flash program memory, 1KB of SRAM, and 256 bytes of EEPROM, housed in a 28-pin SSOP package. It operates up to 32MHz with Core Independent Peripherals, integrated LCD drive, 12-bit ADC2 with up to 20 channels, a 5-bit DAC, low-power comparator, and XLP (eXtreme Low Power) technology for battery-powered designs. An 8-bit microcontroller (MCU) is a single-chip processor that integrates a CPU, program memory (Flash), data memory (SRAM), non-volatile storage (EEPROM), and a rich set of peripherals (ADC, timers, communication interfaces) on a single silicon die. The 8-bit PIC16 family belongs to the larger PIC microcontroller hierarchy from Microchip, sitting below the PIC18 (8-bit, higher performance), PIC24/dsPIC (16-bit), and PIC32 (32-bit) families. Within embedded systems, 8-bit MCUs are typically used in cost-sensitive, low-power applications where computational throughput requirements are modest — sensor nodes, consumer appliances, simple motor control, and human-machine interfaces. Key differentiating features include the integrated charge pump for LCD bias generation (eliminating external discrete bias components), 4 x 16-bit timers, PWM/CCP/CWG waveform generators, SMT (Signal Measurement Timer), ZCD (Zero-Cross Detect), RTCC (Real-Time Clock Calendar), and PPS (Peripheral Pin Select) for flexible pin remapping. The XLP variant delivers typical sleep currents below 1 µA, making the part especially suited to battery-powered LCD applications such as thermostats, utility meters, and portable instrumentation. Architecturally, the PIC16F19155 uses a Harvard RISC core with a 14-bit instruction word and a single-cycle instruction pipeline at 32MHz (8MIPS). The device supports 1.8V–5.5V operation across an industrial temperature range of -40°C to +85°C, and includes Core Independent Peripherals (CIPs) that operate without CPU intervention for tasks like waveform generation, signal measurement, and ADC triggering — reducing firmware complexity and power consumption. Typical applications include battery-powered LCD display modules, IoT sensor nodes, smart thermostats, utility metering, consumer appliance interfaces, and low-power industrial sensor transmitters. The integrated LCD driver (up to 96 segments) and charge pump allow direct connection to segmented LCD glass without an external bias generator. When designing with this part, allocate PCB area for the ICSPDAT/ICSPCLK programming/debug pins and ensure the VDD/VSS decoupling network uses 100nF ceramic capacitors placed within 5mm of the supply pins. For noise-sensitive analog measurements, configure the FVR (Fixed Voltage Reference) for stable ADC readings across temperature. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone — including thermal/power budgets and cross-brand cross-reference guidance.

RFQ संपर्क
PIC16F19155T-I/MV - 8-bit MCU, 14KB Flash, 32MHz, LCD | Microchip
PIC16F19155T-I/MV

PIC16F19155T-I/MV - 8-bit MCU, 14KB Flash, 32MHz, LCD | Microchip

The Microchip Technology PIC16F19155T-I/MV is a 32MHz 8-bit PIC microcontroller with 14KB Flash, 1024 bytes RAM, and 256 bytes EEPROM, housed in a 28-pin UQFN (4x4 mm) package with eXtreme Low-Power (XLP) technology and integrated LCD drive. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory (typically Flash), volatile data memory (RAM), and a rich set of on-chip peripherals such as timers, ADCs, communication interfaces and I/O pins. The PIC16F19155 belongs to Microchip's enhanced mid-range PIC16F191xx family, which targets ultra-low-power applications that require segmented LCD support, core-independent peripherals (CIPs), and intelligent analog on-chip. As a member of the broader PIC microcontroller family, it sits below PIC24/dsPIC parts and above baseline PIC10/12/16 devices in capability. Key features include 14KB (8K x 14) self-programmable Flash program memory, 1024 bytes SRAM, 256 bytes data EEPROM, a 12-bit ADC2 with up to 20 channels, a 5-bit DAC, two comparators (one low-power, one high-speed), two CCP modules, two 10-bit PWM channels, and one Complementary Waveform Generator (CWG). Up to 24 I/O pins are available, and the integrated LCD driver supports up to 96 segments using an on-chip charge pump so the MCU can bias the LCD directly from a low-voltage battery without external boost components. The XLP idle current and active clock tuning of HFINTOSC over voltage/temperature enable long battery life in metering and wearable applications. The device is built on CMOS technology and executes most instructions in one instruction cycle through the enhanced mid-range 16-bit instruction set. Core-independent peripherals such as the CWG, SMT (Signal Measurement Timer), ZCD (Zero-Cross Detect), and configurable PPS (Peripheral Pin Select) allow the MCU to handle complex timing, motor, and zero-cross switching tasks without CPU intervention, freeing the core for application logic. Typical applications include battery-powered LCD thermostats and utility meters, IoT sensor nodes with LCD readouts, home appliance user interfaces, portable medical monitors, and industrial control panels with segment displays. The wide operating voltage range (1.8V to 5.5V) and integrated charge pump also make the part attractive for 3V coin-cell designs where a display must remain visible down to deep battery voltages. When designing with this device, ensure the charge-pump capacitor and bias resistors match the selected LCD glass (Microchip AN658 - LCD Fundamentals). Use PPS for flexible pin assignment and place a 0.1uF decoupling capacitor on VDD within 2mm of the pin to keep ADC2 noise low. This page synthesizes distributor pricing, pin-compatible alternatives within the same 28-pin UQFN family, and practical design notes not aggregated on any single distributor listing, providing an at-a-glance engineering comparison.

RFQ संपर्क
PIC16F19155T-I/SO - 14KB Flash, 32MHz XLP LCD MCU | Microchip
PIC16F19155T-I/SO

PIC16F19155T-I/SO - 14KB Flash, 32MHz XLP LCD MCU | Microchip

The Microchip Technology PIC16F19155T-I/SO is an 8-bit PIC microcontroller in the PIC16F191xx family featuring 14KB Flash, 1KB RAM, and 256B EEPROM, packaged in a 28-pin SOIC (7.50mm body width). It runs at up to 32MHz from a 2.0V to 5.5V supply with eXtreme Low-Power (XLP) technology tailored for battery-powered LCD applications. What is an 8-bit microcontroller? An 8-bit microcontroller is a single-chip computer with an 8-bit data path, integrating a CPU, volatile and non-volatile memory, and configurable peripherals around a common bus. It sits in the broader taxonomy of microcontroller -> embedded MCU -> semiconductor device, and the PIC16 family is one of the industry-standard 8-bit architectures optimized for low-power deterministic control. Key features of the PIC16F19155 include 14KB (8K x 14) Flash program memory, 12-bit ADC2 with computation, 5-bit DAC, low-power comparator, PWM, CCP, CWG, SMT timer, ZCD, PPS, RTCC, and a charge pump for LCD bias generation. The device supports nanoWatt XLP sleep currents below 50 nA in Retention mode and includes Core Independent Peripherals (CIPs) that operate autonomously of the CPU. Architecturally, the part uses a Harvard RISC-based PIC16 core with a 14-bit instruction word, 49 instructions, and hardware multiply. Intelligent analog with 12-bit ADC2, DAC, and LP COMP, plus a charge pump that maintains LCD contrast as VDD falls, makes it ideal for metering and other LCD-driven instruments. The peripheral pin select (PPS) block allows flexible function remapping. Typical applications include battery-powered LCD meters, IoT sensor nodes, white goods user interfaces, medical glucose meters, and remote control keypads. Designers choose it whenever an integrated charge pump for LCD bias and ultra-low sleep current are needed in a 28-SOIC footprint. Design consideration: keep the charge-pump capacitors (typically 1uF ceramic) as close as physically possible to the respective LCD bias pins. Use PPS to reassign peripherals to lower pin numbers to free higher pin numbers for dedicated analog I/O. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that are not collated in the manufacturer datasheet alone.

RFQ संपर्क
PIC16F19155T-I/SS - 14KB Flash 8-bit LCD XLP MCU | Microchip
PIC16F19155T-I/SS

PIC16F19155T-I/SS - 14KB Flash 8-bit LCD XLP MCU | Microchip

The Microchip Technology PIC16F19155T-I/SS is an 8-bit PIC microcontroller built on the eXtreme Low Power (XLP) architecture, featuring 14 KB of Flash program memory, 1 KB of SRAM, and 256 bytes of EEPROM in a 28-pin SSOP package. The device operates at up to 32 MHz from a 2.3V to 5.5V supply and integrates an LCD driver with charge pump, a 12-bit ADC2, 5-bit DAC, low-power comparators, PWM, CCP, CWG, SMT timer, ZCD, PPS, and RTCC. The trailing "/SS" designates the 28-pin SSOP package, while the "/T" indicates Tape & Reel packaging and "-I" indicates the industrial -40C to +85C temperature grade. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable peripherals. The PIC16F19155 belongs to the PIC16F mid-range 8-bit family, sitting in the hierarchy: PIC16F19155 -> PIC16F191xx family -> PIC16F series -> 8-bit PIC MCUs -> Microchip MCU portfolio -> semiconductor. The XLP designation means the part is engineered for ultra-low-power battery applications using nanoWatt3C technology, with typical sleep currents measured in nanoamps. Key features include an integrated LCD charge pump supporting displays up to 288 segments, a 12-bit ADC2 with computation, multiple Core Independent Peripherals (CIPs) such as CWG, NCO, and SMT that offload tasks from the CPU, Peripheral Pin Select (PPS) for flexible I/O mapping, and an RTCC module with timestamps. The 32 MHz internal oscillator eliminates the need for an external crystal in cost-sensitive designs. The architecture combines a 14-bit instruction word PIC CPU with Harvard bus separation, allowing simultaneous instruction fetch and data access. The on-board charge pump maintains LCD contrast even as battery voltage drops, and the XLP sleep modes with retention keep total current draw below 50 nA in deep sleep. Typical applications include battery-powered LCD thermostats, portable medical monitors with segment displays, IoT sensor nodes with local LCD readouts, white-goods user interfaces, and metering equipment. The integrated LCD driver with charge pump removes the need for an external boost converter in single-cell battery designs. When designing with this part, verify the SSOP-28 footprint matches the LCD segment pin assignments you require. The PPS feature lets you remap most peripherals to alternative I/O pins, simplifying PCB layout when display or sensor routing conflicts arise. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ संपर्क
PIC16F19156-E/SO - 8-bit 32MHz XLP MCU 28KB Flash | Microchip
PIC16F19156-E/SO

PIC16F19156-E/SO - 8-bit 32MHz XLP MCU 28KB Flash | Microchip

The Microchip Technology PIC16F19156-E/SO is an 8-bit PIC® XLP™ microcontroller featuring 28KB of Flash program memory, 2KB of RAM, and 256 bytes of EEPROM, operating at up to 32MHz from a 1.8V to 5.5V supply in a 28-pin SOIC package. It integrates eXtreme Low-Power (XLP) technology, Core Independent Peripherals (CIPs), and an on-chip LCD driver with integrated charge pump, making it ideally suited for battery-powered display applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), peripherals, and I/O into one package. The PIC16F19156 belongs to the 8-bit MCU category, which trades raw compute throughput for ultra-low power consumption, deterministic interrupt response, and low cost. The hierarchy is: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. 8-bit MCUs remain dominant in cost- and power-sensitive segments such as consumer appliances, IoT sensors, and battery-powered instrumentation. Key features include 28KB (16K x 14) self-programmable Flash, hardware LCD driver with charge pump capable of driving high-segment-count displays without external boost components, up to 256KB of addressable EEPROM emulation, and a rich set of Core Independent Peripherals including Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), Numerically Controlled Oscillator (NCO), and multiple PWM/CCP modules. The XLP Sleep mode current is engineered for multi-year coin-cell operation. The PIC16F19156 is built on an enhanced mid-range PIC16 core with a 14-bit instruction word, Harvard architecture, and 32MHz internal oscillator. It includes intelligent analog features such as a 12-bit ADC with computation, two comparators, a DAC, and a Zero-Cross Detect module. Hardware CRC and memory scan simplify IEC 60730 Class B safety compliance for appliance designs. Typical applications include battery-powered LCD gauges, IoT sensor nodes, medical monitoring devices with display readouts, home-automation keypads with LCD, industrial HMI panels, and metering equipment. The integrated LCD charge pump eliminates external DC-DC boost converters, shrinking BOM cost and PCB area. When designing with this MCU, place a 0.1uF decoupling capacitor as close as possible to VDD and reserve a 1uF bulk capacitor near the LCD charge-pump output pins if driving high-segment loads. Route the 32kHz low-power crystal traces short and guarded to minimize leakage in sleep-current-critical applications. This page synthesizes distributor pricing, same-package drop-in alternatives from the PIC16F1915x family, and practical design notes not consolidated in the manufacturer datasheet, helping engineers evaluate replacements, design thermal/battery budgets, and select pin-compatible variants.

RFQ संपर्क
PIC16F19156-E/SP - 8-bit 32MHz XLP MCU 28KB Flash 28-SPDIP | Microchip
PIC16F19156-E/SP

PIC16F19156-E/SP - 8-bit 32MHz XLP MCU 28KB Flash 28-SPDIP | Microchip

The Microchip Technology PIC16F19156-E/SP is an 8-bit PIC16 microcontroller built around the eXtreme Low-Power (XLP) architecture, integrating an integrated LCD driver, Core Independent Peripherals (CIPs) and Intelligent Analog in a 28-pin SPDIP through-hole package. The CPU runs up to 32 MHz with 28 KB of Flash program memory, 2 KB of SRAM and 256 bytes of EEPROM, and the device is offered in an extended (-40C to +125C) operating temperature grade. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and a configurable set of peripherals (ADCs, timers, communication blocks, I/O). The PIC16F19156 family sits in the 8-bit PIC16 hierarchy under the broader PIC microcontroller taxonomy within Microchip's product tree. XLP variants are engineered for ultra-low-power battery applications, often using nanoWatt XLP technology to extend idle-current endurance. Key features include integrated segmented LCD drive (up to 116 segments), a 12-bit ADC2 with computation, a 5-bit DAC, low-power comparator, Zero-Cross Detect (ZCD), Complementary Waveform Generator (CWG), SMT (Signal Measurement Timer), RTCC, Hardware Limit Timer (HLT), Windowed WWDT, PWM, CCP, Peripheral Pin Select (PPS) and Power-Managed modes. The high-current I/O pins can directly drive LCD backplanes or external power components. Typical applications cover battery-powered LCD consumer devices, industrial automation HMIs, low-cost instrumentation, and consumer appliances. An integrated charge pump and XLP sleep currents in the nano-ampere class make the part especially suited to mains-free product categories where long battery life and a built-in display matter more than raw CPU throughput. When designing with this device, ensure the configured system clock stays within the 2.5V-5.5V VDD range for full 32 MHz operation; below 2.5V the maximum fOSC derates. Decouple VDD with a 100 nF ceramic close to each power pin and place the ICD 3/4 or PICkit programmer footprint so firmware can be updated without board rework. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes that go beyond what the manufacturer datasheet alone provides for the PIC16F19156-E/SP.

RFQ संपर्क
PIC16F19156-I/SO - 8-bit MCU 28KB Flash LCD XLP 28-SOIC | Microchip
PIC16F19156-I/SO

PIC16F19156-I/SO - 8-bit MCU 28KB Flash LCD XLP 28-SOIC | Microchip

The Microchip Technology PIC16F19156-I/SO is an 8-bit PIC microcontroller from the PIC16F19155/56/75/76/85/86 family, featuring 28KB of Flash program memory, 2KB of RAM, and 256 bytes of EEPROM, housed in a 28-pin SOIC package with the industrial -40C to +85C temperature range. The core runs at up to 32 MHz and integrates an integrated LCD driver, charge pump, 12-bit ADC2 with computation, a 5-bit DAC, low-power comparators (LP COMP), PWM, CCP, CWG, SMT, ZCD, PPS, and a Real-Time Calendar and Counter (RTCC) peripheral block. An 8-bit microcontroller (MCU) is a microprocessor that processes data 8 bits at a time and integrates CPU, Flash, RAM, EEPROM, and peripherals on a single die. PIC16F MCUs sit in the broader hierarchy of microcontrollers -> microcontrollers + peripherals -> ultra-low-power MCUs -> battery-powered embedded platforms. The PIC16F19156 belongs to the eXtreme Low-Power (XLP) family, a sub-family characterized by deep-sleep currents in the sub-uA range and integrated LCD drive for small-form-factor battery-powered products. Key features that differentiate this part include: integrated charge pump for display contrast generation without external DC-DC hardware; 12-bit ADC2 with automated accumulators and burst-averaging for sensor signal chains; and Core Independent Peripherals (CIPs) such as CWG, SMT, ZCD, and PWM that run autonomously from the core, reducing wake cycles and prolonging battery life. The architecture is a RISC-based PIC16 enhanced mid-range core with a hardware call stack and a peripheral-rich interrupt structure. The instruction set is fixed-width 14-bit, allowing deterministic execution useful for real-time loops. The 28-pin SOIC provides 24 usable I/O plus dedicated analog and oscillator pins, while the 256-byte EEPROM supports per-unit calibration and runtime configuration storage without external NVM. Typical applications include battery-powered LCD thermostats, IoT sensor nodes with on-glass displays, smart metering HMIs, medical handheld glucose or pulse monitors, and industrial panel indicators. The integrated LCD drive eliminates an external LCD controller, reducing BOM count on small-format displays. When selecting this part, evaluate whether the 28-pin SOIC footprint fits your enclosure, since smaller-package variants exist (SSOP, QFN). Also confirm that the -I (industrial) temperature grade of -40C to +85C is sufficient; a -E (extended) grade spanning -40C to +125C is available for harsher environments. Programming is via ICSP over two pins, which frees the rest of the pin budget for application IO. This page synthesizes distributor pricing from DigiKey and Mouser, a same-brand drop-in alternative list, and practical design notes drawn from the Microchip PIC16F19156 family data covering tools, power, and PCB layout.

RFQ संपर्क
PIC16F19156-I/SS - 28KB Flash XLP LCD MCU 32MHz | Microchip
PIC16F19156-I/SS

PIC16F19156-I/SS - 28KB Flash XLP LCD MCU 32MHz | Microchip

The Microchip Technology PIC16F19156-I/SS is an 8-bit RISC PIC16-family microcontroller operating up to 32 MHz, integrating 28 KB of self-programmable Flash program memory, 2 KB SRAM and 256 bytes of EEPROM. Housed in a 28-pin SSOP (0.209" / 5.30 mm width) package, it is qualified to the industrial temperature range (-40C to +85C). An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, optimised for deterministic real-time control with low power and low cost. The PIC16F19156 sits in the hierarchy 8-bit MCU -> microcontroller -> embedded processor -> semiconductor, and is targeted by Microchip's MPLAB X IDE + XC8 toolchain. The 'XLP' (eXtreme Low Power) family extends battery life with sub-uA sleep currents and a charge-pump-augmented LCD driver. Key differentiating features include: integrated LCD driver with charge pump, 12-bit ADC2 with computation, 5-/8-bit DAC, two rail-to-rail comparators with programmable hysteresis, four Configurable Logic Cells (CLC), four 16-bit PWM, three Capture/Compare/PWM (CCP), Complementary Waveform Generator (CWG), Signal Measurement Timer (SMT), Zero-Cross Detect (ZCD), Peripheral Pin Select (PPS) and a Real-Time Clock/Calendar (RTCC). Up to 43 high-current sink/source I/O support LED drive directly. The PIC16F19156 uses a 14-bit instruction word Harvard architecture with a hardware stack and 32 interrupt sources. Core-independent peripherals (CLC, CWG, PWM, SMT, ZCD) operate without CPU wake-up, dramatically reducing average power in event-driven designs and freeing the CPU for application logic. Typical applications include battery-powered LCD keypads, IoT sensor nodes with display, low-cost utility meters, smart thermostats, white-goods user-interface boards, and handheld medical/wellness devices. The on-chip charge pump drives contrast even at low battery, and the 12-bit ADC2 with computation offloads averaging, filtering, and threshold checks in sensor-conditioning firmware. When designing with this device, keep VDD between 2.3 V and 5.5 V (F-version) and pay attention to PPS remap conflicts: each peripheral function can be routed to only one pin at a time, so a wrong configuration silently breaks the schematic intent. Verify PPS lock bits before final code lock. This page synthesises current distributor pricing, parametric comparison, and pin-compatible PIC16 same-package drop-in alternatives, providing context not found in the bare datasheet.

RFQ संपर्क
PIC16F19156T-I/SO - 28KB Flash XLP MCU with LCD | Microchip
PIC16F19156T-I/SO

PIC16F19156T-I/SO - 28KB Flash XLP MCU with LCD | Microchip

The Microchip Technology PIC16F19156T-I/SO is an 8-bit PIC microcontroller featuring 28KB of Flash program memory, 2KB of RAM, and 256 bytes of EEPROM, housed in a 28-pin SOIC package. It operates at up to 32 MHz with a 3V supply and integrates Xtreme Low-Power (XLP) technology, an LCD driver with integrated charge pump, and core independent peripherals including a 12-bit ADC2, DAC, low-power comparator, PWM, CCP, CWG, SMT, ZCD, PPS, and RTCC. What is an 8-bit microcontroller? An MCU (microcontroller unit) is a single-chip computer that integrates a CPU core, program memory, working RAM, non-volatile data EEPROM, and a rich set of mixed-signal peripherals. 8-bit MCUs use an 8-bit data path and are favored for deterministic real-time control, ultra-low sleep current, and low BOM cost. The PIC16 family sits between PIC10/PIC12 baseline parts and PIC18/PIC24 mid-range parts, occupying the XLP sweet spot for battery-powered and human-machine interface designs. Key features include eXtreme Low-Power (XLP) operation suitable for battery-powered applications, an integrated charge pump that generates LCD bias voltages directly from a single Li-ion cell, high-current I/O pins for direct LED drive, and Core Independent Peripherals (CIPs) that offload timing-critical tasks from the CPU. The device also offers Peripheral Pin Select (PPS) for flexible signal routing and a 12-bit ADC2 with computation. Architecturally, the PIC16F19156T-I/SO uses a RISC Harvard-bus core with a hardware multiplier, executes most instructions in a single cycle, and provides a vectored interrupt controller. The integrated LCD driver supports up to a defined segment count and runs from an internal charge pump so no external bias network is needed. Typical applications include battery-powered LCD dashboards, smart thermostats, IoT sensor nodes with displays, medical glucose and infusion meters, consumer white goods with segment displays, and industrial HMI panels. The wide operating voltage range down to below 2V and nanoWatt sleep modes make it ideal for any product that must run for years on a single battery while driving an LCD. When designing with this part, plan decoupling with a 100 nF ceramic bypass close to VDD, and follow the recommended LCD bias capacitor values from the datasheet to avoid ripple on the display. Use the Peripheral Pin Select feature to remap peripherals and keep PCB layout changes minimal when porting from older PIC16 designs. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ संपर्क
PIC16F19175-E/MV - 8-Bit 32MHz 14KB Flash XLP MCU | Microchip
PIC16F19175-E/MV

PIC16F19175-E/MV - 8-Bit 32MHz 14KB Flash XLP MCU | Microchip

The Microchip PIC16F19175-E/MV is an 8-bit RISC PIC microcontroller operating at up to 32MHz, featuring 14KB (8K x 14) of Flash program memory, 1KB of SRAM, and 256 bytes of EEPROM in a 40-pin UQFN (5x5 mm) package with exposed pad. The device integrates eXtreme Low-Power (XLP) technology, a charge pump for battery-powered LCD drive, and Core Independent Peripherals (CIPs) including a 12-bit ADC2, 5-bit DAC, low-power comparator, PWM, CCP, CWG, SMT, ZCD, PPS, and RTCC. An 8-bit PIC microcontroller is a Harvard-architecture RISC device that executes one instruction per clock cycle (excluding branches), positioning it within the microcontroller hierarchy: PIC16 -> PIC microcontrollers -> 8-bit MCU family -> microcontroller -> embedded semiconductor -> integrated circuit. PIC16F19175 belongs to the enhanced mid-range core family and is engineered for low-power, peripheral-rich applications where deterministic behaviour and long battery life are mandatory. Key features include the integrated charge pump that maintains LCD contrast even when the battery voltage drops below the LCD threshold, high-current I/O for direct LED drive, and Intelligent Analog peripherals that operate independently of the CPU. The wide operating voltage range of 2.3V to 5.5V accommodates 2-cell alkaline, NiMH, and primary Li-coin chemistries. Sleep currents in the nanoamp range extend shelf life in always-on products. The PIC16F19175-E/MV uses an enhanced mid-range PIC16 core with a 14-bit instruction word and hardware multiplier assist. The 32MHz internal oscillator removes the need for an external crystal in cost-sensitive designs, while the Peripheral Pin Select (PPS) remapping allows digital peripherals to be routed to a wide range of I/O pins, simplifying PCB layout when functions move late in the design cycle. The 5x5 mm UQFN package with exposed thermal pad supports compact, thermally efficient layouts. Typical applications include battery-powered LCD consumer products, IoT sensor nodes with segmented displays, medical glucose meters and thermometers, industrial metering with on-glass LCD readouts, and automotive body controllers. The combination of XLP current profiles, on-chip LCD drive, and the charge pump makes the part especially well suited for portable devices that must display data without an external boost converter. When designing with this device, allocate PCB copper directly under the exposed thermal pad and stitch vias into the inner ground plane to meet thermal and EMI targets. Use Microchip's MPLAB X IDE with XC8 compiler and MPLAB Code Configurator (MCC) for peripheral setup; the auto-generated code accelerates CIP configuration but should still be reviewed against the device datasheet's electrical characteristics. This page synthesises distributor pricing, same-family drop-in alternatives, application notes, and practical design guidance for the PIC16F19175-E/MV that go beyond the manufacturer datasheet alone, giving engineers and buyers a single reference for selection, sourcing, and integration.

RFQ संपर्क
PIC16F19175-E/PT - 8-bit 32MHz 14KB Flash LCD MCU | Microchip
PIC16F19175-E/PT

PIC16F19175-E/PT - 8-bit 32MHz 14KB Flash LCD MCU | Microchip

The Microchip Technology PIC16F19175-E/PT is a 8-bit PIC® XLP™ microcontroller featuring 14 KB Flash program memory, 1024 bytes RAM, and 256 bytes EEPROM, housed in a 44-pin TQFP (10x10 mm) package with extended -40C to +125C operating range. It integrates an integrated LCD driver with charge pump, 12-bit ADC2, 5-bit/8-bit DAC, low-power comparators, PWM, CCP, CWG, SMT timer, ZCD, and PPS in a single low-power MCU designed for battery-powered LCD applications. The 32 MHz core delivers 8 MIPS performance while consuming only microamps in sleep, making it ideal for energy-constrained designs. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash/ROM), data memory (RAM), and integrated peripherals such as ADCs, timers, communication interfaces, and I/O pins. PIC® microcontrollers use a RISC architecture with a fixed instruction set optimized for deterministic real-time control, placing them in the broader hierarchy of microcontrollers -> embedded controllers -> semiconductor ICs. The XLP™ (eXtreme Low-Power) family is specifically tuned for battery-powered applications where sleep current is critical. Key features include the integrated LCD charge pump that generates VLCD from the main supply without external boost components, 12-bit ADC2 with computation, dual low-power comparators with programmable reference, and Core Independent Peripherals (CIPs) that operate without CPU intervention. The device supports 1.8V-5.5V operation across the PIC16F19175 (F) variant with on-chip voltage regulator and brown-out reset. Intelligent Analog peripherals include the 12-bit ADC, 5/8-bit DAC, and zero-cross detect (ZCD) for TRIAC control. The PIC16F19175 uses Microchip's enhanced mid-range 8-bit core running at 32 MHz with 8 MIPS throughput, supported by 14 KB self-programmable Flash, 1024 bytes SRAM, and 256 bytes high-endurance EEPROM (100k erase/write cycles). Hardware CIPs include the SMT (Signal Measurement Timer), CWG (Complementary Waveform Generator), and Configurable Logic Cell, enabling complex timing and signal generation tasks without software overhead. Typical applications include battery-powered glucose meters and blood pressure monitors with LCD readout, smart thermostats and HVAC controllers, industrial sensor transmitters with LCD display, electronic shelf labels (ESL), utility metering endpoints with LCD, and remote control units with status display. The integrated LCD driver supporting up to 357 segments eliminates external display drivers. When designing with this device, pay attention to VLCD charge pump capacitor selection and consider the 5x8 font ROM for ASCII character generation. The PPS (Peripheral Pin Select) provides flexible I/O mapping, but designers must still respect analog/digital pin separation to avoid injection current issues.

RFQ संपर्क
PIC16F19175-I/MV - 14KB Flash 8-bit XLP LCD MCU | Microchip
PIC16F19175-I/MV

PIC16F19175-I/MV - 14KB Flash 8-bit XLP LCD MCU | Microchip

The Microchip Technology PIC16F19175-I/MV is an 8-bit PIC microcontroller from the PIC16F191xx family that pairs eXtreme Low-Power (XLP) operation with integrated LCD drive and Core Independent Peripherals, delivered in a 40-pin UQFN (MV) package measuring 5x5 mm. The device integrates 14 KB of Flash program memory, 1 KB of SRAM, and 256 bytes of EEPROM, and runs at speeds up to 32 MHz. Its on-board analog includes a 12-bit ADC2 with computation, a 5-/8-bit DAC, low-power comparators, zero-cross detection, and a charge-pump-assisted LCD driver capable of up to 280 segments. Background: A PIC microcontroller is an 8-bit RISC-class embedded processor built around a Harvard architecture with separate program and data buses, executing one instruction per clock cycle and supported by a rich set of Core Independent Peripherals (CIPs) that operate without CPU intervention. PIC microcontrollers sit within the broader hierarchy: microcontroller -> embedded processor -> semiconductor, and are widely used in ultra-low-power battery applications where deterministic behaviour and low quiescent current are critical. The XLP designation signals a part optimised for sub-uA sleep currents, making it a member of the power management ecosystem at the device level. Key features include active current consumption in the microamp range, multiple low-power sleep modes (doze, idle, sleep), an integrated LCD charge pump that maintains contrast down to 1.8 V, and high-current I/O pins suitable for direct LED drive. The 12-bit ADC2 with averaging and accumulation, combined with the on-chip 5-/8-bit DAC and zero-cross detect, supports intelligent analog front-ends for sensor conditioning and motor control without external components. Technical depth: the CIP block includes Complementary Waveform Generator (CWG), Configurable Logic Cell (CLC), Signal Measurement Timer (SMT), PWM, CCP, and Peripheral Pin Select (PPS), allowing timing-critical logic to run autonomously while the CPU sleeps. PPS remaps most digital peripherals to a wide choice of I/O pins, simplifying PCB routing on dense mixed-signal boards. Typical applications span battery-powered LCD keypads, IoT sensor nodes, consumer white goods with LCD displays, and portable medical monitors requiring long standby time. The integrated LCD charge pump makes it ideal when the system must display information down to a nearly discharged battery. When designing with this part, prefer PPS to route peripherals to the most convenient pins and exploit CIPs so the CPU can spend most of its time in sleep. Always validate sleep current against the application budget; the XLP spec is best realised when wake-up events are driven by CIPs rather than interrupts.

RFQ संपर्क
PIC16F19175T-I/MV - 32MHz 8-Bit XLP MCU 14KB Flash LCD | Microchip
PIC16F19175T-I/MV

PIC16F19175T-I/MV - 32MHz 8-Bit XLP MCU 14KB Flash LCD | Microchip

The Microchip PIC16F19175T-I/MV is a 32MHz 8-bit PIC RISC microcontroller featuring 14KB (8K x 14 words) of Flash program memory, 1KB of SRAM, and 256 bytes of EEPROM, housed in a 40-pin UQFN (5x5 mm) package with an exposed thermal pad. It belongs to the PIC® XLP™ 16F family and integrates Core Independent Peripherals (CIPs), Intelligent Analog, and an integrated LCD driver with charge pump, making it especially well suited for battery-powered display applications. An 8-bit microcontroller (MCU) is a programmable logic device that executes instructions from internal Flash memory at a clock rate up to 32MHz. The PIC16F19175T-I/MV sits within the broader hierarchy of microcontrollers -> 8-bit MCUs -> PIC microcontrollers -> XLP (eXtreme Low Power) family -> power management MCUs. Its integrated charge pump and LCD drive enable glass bias generation without external DC-DC circuitry, while XLP technology delivers sub-µA sleep currents for battery longevity. Key differentiating features include 35 high-current I/O pins, a 12-bit ADC² (Analog-to-Digital Converter with Computation), a 5-bit DAC, low-power comparators (LP COMP), PWM, CCP, CWG, SMT, ZCD, and PPS (Peripheral Pin Select). The integrated LCD driver supports up to 280 segments, and the eXtreme Low Power (XLP) architecture delivers typical sleep currents in the nanoamp range, enabling years of operation from a single coin cell. The 12-bit ADC² autonomously performs signal conditioning such as averaging and threshold comparisons without CPU intervention. Architecturally, the device uses an enhanced mid-range 8-bit CPU core with a hardware multiplier, 14-bit instruction word, and 16-level hardware stack, allowing deterministic interrupt response and predictable real-time behavior. The integrated charge pump generates the VPP LCD bias voltage from a low-voltage source, eliminating an external boost circuit. Combined with PPS routing and Core Independent Peripherals, the chip dramatically reduces firmware complexity and BOM cost. Typical applications include battery-powered LCD meters and thermostats, IoT sensor nodes with displays, portable medical devices (glucometers, pulse oximeters), consumer appliances with segment displays, and industrial HMIs. The PIC16F19175T-I/MV is the tape-and-reel variant; the PIC16F19175-I/MV is the tray variant. Designers should also consider the pin-compatible PIC16F19155 (less Flash/RAM) and PIC16F19176 (more Flash) for memory scaling within the same package. For PCB layout, place a 0.1µF decoupling capacitor as close as possible to each VDD pin and bond the exposed pad (EP) to a continuous ground plane for thermal dissipation. Program/debug is supported via ICSP™ on RA0/RA1, and the PPS system allows most digital peripherals to be reassigned to multiple I/O pins for flexible board routing. This page synthesizes Microchip datasheet specifications, current distributor pricing, verified drop-in same-family alternatives, and practical design notes that go beyond the manufacturer datasheet, providing an engineering-grade reference for the PIC16F19175T-I/MV.

RFQ संपर्क
PIC16F19175T-I/PT - 8-bit MCU 32MHz 14KB FLASH 44-TQFP
PIC16F19175T-I/PT

PIC16F19175T-I/PT - 8-bit MCU 32MHz 14KB FLASH 44-TQFP

The Microchip Technology PIC16F19175T-I/PT is an 8-bit PIC microcontroller featuring a PIC16 CPU core, 32 MHz maximum clock speed, 14 KB (8K x 14) Flash program memory, 1 KB SRAM, and 256 bytes of data EEPROM in a 44-pin TQFP (10x10 mm) surface-mount package. CMOS process technology and Microchip's eXtreme Low-Power (XLP) architecture target battery-powered and LCD-driven designs. The -I/PT suffix denotes the industrial temperature grade (-40C to +85C) supplied in tape-and-reel packaging. An 8-bit PIC microcontroller is a Harvard-architecture RISC device widely used in embedded control. MCUs sit within the broader taxonomy of microcontrollers -> embedded processors -> semiconductors; within Microchip's portfolio, PIC16 devices fill the mid-range 8-bit niche between baseline PIC10/12 and high-performance PIC18/DSPIC. Compared with 32-bit Cortex-M parts, PIC16 MCUs offer simpler toolchains, lower cost, and lower active current for cost-sensitive applications. Differentiating features of the PIC16F19175 include an integrated charge pump and high-current I/O for direct LCD display drive, hardware CRC/SCAN, Windowed Watchdog Timer (WWDT), Hardware Limit Timer (HLT), Core Independent Peripherals (CIPs), Intelligent Analog peripherals such as a 12-bit ADC and 5-bit DAC, and on-chip EEPROM for non-volatile user data. The 32 MHz internal oscillator eliminates an external crystal in many designs. The architecture combines a single-cycle PIC16 ALU with a unified peripheral set that can operate without CPU intervention, reducing active time and average power. The XLP Sleep mode draws extremely low current, allowing battery designs to wake only for short measurement events. Separate analog/digital supply pins and a wide operating voltage range (typically 1.8 V to 5.5 V) further simplify portable designs. Typical applications include battery-powered LCD meters, white-goods and appliance user interfaces, IoT sensor nodes, and industrial control panels. The integrated charge pump and segment/segment-common LCD driver make the part especially suited for character or segment LCDs without external biasing hardware. Designers should evaluate RAM and Flash headroom carefully: 1 KB SRAM and 14 KB Flash fit only modest stacks and feature sets. For code migration, the same PIC16F191xx silicon is offered in smaller packages (e.g., 28-pin SPDIP/SOIC) allowing PCB layout reuse. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design guidance not consolidated in any single distributor listing.

RFQ संपर्क
PIC16F19176-E/MV - 28KB Flash 8-bit MCU, XLP, LCD | Microchip
PIC16F19176-E/MV

PIC16F19176-E/MV - 28KB Flash 8-bit MCU, XLP, LCD | Microchip

The Microchip Technology PIC16F19176-E/MV is an 8-bit PIC microcontroller from the PIC16F191xx family that combines 28 KB of Flash program memory with eXtreme Low-Power (XLP) technology, integrated LCD drive, and a rich set of Core Independent Peripherals (CIPs). It runs at up to 32 MHz, includes 2 KB of SRAM and 256 bytes of EEPROM, and is housed in a 40-pin UQFN (MV) package measuring 5x5 mm with an exposed pad. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and a configurable peripheral set. Within the broader taxonomy it is a microprocessor subcategory (microprocessor -> microcontroller -> 8-bit microcontroller -> PIC16 family -> PIC16F19176 sub-family). MCUs are typically chosen for embedded control tasks where deterministic low-latency response, low quiescent power, and minimal external component count matter more than raw computational throughput. Key features of the PIC16F19176-E/MV include 12-bit ADC2 with computation, 5-bit DAC, two comparators with a low-power variant, 8-bit and 16-bit timers, PWM, CCP, CWG (Complementary Waveform Generator), SMT (Signal Measurement Timer), ZCD (Zero-Cross Detect), PPS (Peripheral Pin Select), and an RTCC (Real-Time Clock/Calendar). The device integrates an LCD charge pump and high-current I/O, making it particularly suited to battery-powered LCD applications. The MV (UQFN-40 5x5) package provides a small PCB footprint with an exposed thermal pad for efficient heat spreading. The device operates from 1.8 V to 5.5 V (F variant) with XLP sleep currents in the sub-microamp range, supporting years of battery life in typical metering or sensor applications. The -E temperature grade covers -40 °C to +125 °C operation. The PPS module remaps digital peripherals to almost any I/O pin, dramatically simplifying PCB routing. The RTCC with hardware timestamp and the LCD driver with up to 360 segments (with charge pump) eliminate external RTC and LCD-voltage-generator chips. Typical applications include battery-powered metering (water/gas/heat), low-power sensor nodes with LCD readouts, electronic shelf labels, thermostats, medical monitors (glucometers, blood-pressure cuffs), and IoT end-node controllers. The combination of LCD, RTCC, and XLP enables a single-chip BOM in many of these designs. When designing, prefer the exposed pad soldered to a continuous copper ground plane for thermal and electrical performance. Decouple VDD with a 100 nF ceramic placed within 5 mm of the pin, and add a bulk 1-10 uF capacitor if the supply impedance is high. Use Microchip's MPLAB X IDE and XC8 compiler for firmware development. This page synthesizes distributor pricing (as of 2026-09-21), drop-in same-package alternatives, and practical design notes that are not duplicated in the manufacturer datasheet.

RFQ संपर्क
PIC16F19176-E/PT - 8-Bit 32MHz XLP MCU 28KB Flash | Microchip
PIC16F19176-E/PT

PIC16F19176-E/PT - 8-Bit 32MHz XLP MCU 28KB Flash | Microchip

The Microchip Technology PIC16F19176-E/PT is an 8-bit RISC microcontroller featuring a PIC16 CPU core, 28KB of FLASH program memory (16K x 14 words), 2KB of SRAM and 256 bytes of EEPROM, running at up to 32MHz internal clock, housed in a 44-pin TQFP (10x10 mm) package. It is part of Microchip's PIC16F191xx family and is engineered around the eXtreme Low-Power (XLP) architecture with integrated LCD drive and Core Independent Peripherals (CIP), targeting battery-powered human-machine-interface products. An 8-bit PIC microcontroller is a Harvard-architecture RISC CPU optimized for embedded control, sitting in the hierarchy: microcontroller -> embedded processor -> semiconductor IC. The 'PIC16' family balances low power, low cost and rich peripherals for consumer, industrial and IoT designs. Within PIC, the 'F' suffix denotes FLASH program memory, while '19176' identifies the part's specific peripheral mix. Key features include: integrated charge pump for direct LCD bias generation, 12-bit ADC with computation (ADC2), 5-bit DAC, low-power comparators, PWM/CCP/CWG (Complementary Waveform Generator), SMT (Signal Measurement Timer), ZCD (Zero-Cross Detector), PPS (Peripheral Pin Select), RTCC (Real-Time Clock Calendar) and high-current I/O for direct LED drive. Per the Microchip product page, the device is especially suited to battery powered LCD applications. The device integrates hardware-based CIP blocks that run autonomously without CPU intervention, freeing the core for power management or comms. XLP modes (Sleep, Doze, Idle, RTC-calibrated wake) deliver nanoWatt-class standby currents, making the PIC16F19176-E/PT a strong fit for sealed, battery-only metering or wearable designs where energy harvesting is impractical. Typical applications include battery powered LCD panels, smart thermostats, IoT sensor nodes with displays, medical glucose and infusion meters, industrial HMI panels, and electronic shelf labels. The wide operating voltage range and integrated charge pump simplify LCD bias design. When designing with the PIC16F19176-E/PT, allocate the PPS module carefully to avoid pin-function conflicts, and use Microchip's MPLAB X IDE with XC8 compiler for code development. The 44-TQFP footprint provides generous I/O access for segment-heavy LCD panels. This page synthesizes distributor stock, pin-compatible drop-in alternatives and practical design notes not found in the manufacturer datasheet alone.

RFQ संपर्क
PIC16F19176-I/MV - 8-bit XLP MCU, 28KB Flash, 32MHz | Microchip
PIC16F19176-I/MV

PIC16F19176-I/MV - 8-bit XLP MCU, 28KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F19176-I/MV is an 8-bit PIC16 XLP microcontroller offering 28 KB of Flash program memory, 2 KB of RAM and 256 bytes of EEPROM, operating at up to 32 MHz in a 40-pin UQFN (MV) 5x5 mm package. The device integrates a charge pump for battery-powered LCD drive, 12-bit ADC2 with DAC, low-power comparators, PWM, CCP, CWG, SMT timers, ZCD, PPS routing and a Real-Time Clock Calendar (RTCC), making it especially suited for ultra-low-power LCD-equipped products. An 8-bit microcontroller (MCU) is a programmable processor that executes instructions one byte at a time using an 8-bit data path. The PIC16 family sits in the broader taxonomy of microcontrollers -> embedded processors -> semiconductors, while XLP (eXtreme Low Power) variants add deep-sleep current management for coin-cell and energy-harvesting applications. The 8-bit PIC16 core provides deterministic instruction execution and a Harvard architecture that simplifies real-time control loops. Key features include a 2.3V to 5.5V supply range, 32 MHz internal oscillator, 12-bit ADC2 with computation, 5-bit DAC, two comparators with selectable references, peripheral pin select (PPS), and an integrated LCD driver supporting up to 320 segments. The device also provides a charge pump that maintains LCD contrast even at low battery voltage, high-current I/O for direct LED drive, and Core Independent Peripherals (CIPs) such as CWG and SMT that offload timing tasks from the CPU. Technically, the PIC16F19176 uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word and 16-level hardware stack. Its XLP architecture supports sleep currents in the sub-microamp range with RTCC and peripherals running, and the integrated LCD charge pump allows glass driving down to 1.8V VDD when configured appropriately. The 40-pin UQFN package minimizes PCB area while exposing the full peripheral set, and PPS enables flexible peripheral-to-pin assignment without re-routing the board. Typical applications include battery-powered medical glucose meters, IoT sensor nodes with LCD readouts, industrial HMI panels, smart thermostats, home appliance user interfaces, and portable instrumentation. The wide operating voltage and integrated LCD charge pump simplify single-coin-cell designs that need a glass display. When designing, place decoupling capacitors within 2 mm of each VDD/VSS pair and follow the recommended ground-return layout for the LCD charge pump capacitors. The PPS feature allows peripheral reassignment post-build, so reserve unused pins in the schematic as a routing safety net. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
PIC16F19176-I/P - 8-bit XLP MCU, 28KB Flash, 40-PDIP | Microchip
PIC16F19176-I/P

PIC16F19176-I/P - 8-bit XLP MCU, 28KB Flash, 40-PDIP | Microchip

The Microchip Technology PIC16F19176-I/P is an 8-bit PIC microcontroller with eXtreme Low-Power (XLP) technology, 28KB of Flash program memory, and an integrated LCD driver, housed in a 40-pin PDIP (DIP) through-hole package. It operates at up to 32 MHz clock speed from a 1.8V to 5.5V supply and integrates 2 KB RAM plus 256 bytes of data EEPROM. An 8-bit microcontroller (MCU) is a small computer-on-a-chip built around a CPU with an 8-bit data path, on-chip program and data memory, and integrated peripherals such as timers, ADCs, and communication interfaces. The PIC16F19176 belongs to the PIC16 family of mid-range MCUs, which sit inside the larger PIC microcontroller hierarchy and ultimately within the embedded microcontroller and microprocessor family. PIC16 parts are known for deterministic instruction execution, small code size, and a broad peripheral set, making them a mainstay of low-power embedded designs. Key features include 12-bit ADC2 with computation, a 5-bit DAC, low-power comparators (LP COMP), PWM, CCP, CWG (Complementary Waveform Generator), SMT (Signal Measurement Timer), ZCD (Zero-Cross Detect), PPS (Peripheral Pin Select), RTCC (Real-Time Clock/Calendar), HLT (Hardware Limit Timer), WWDT (Windowed Watchdog Timer), and PMD (Peripheral Module Disable). An integrated LCD charge pump simplifies LCD bias generation, and high-current I/O pins enable direct LED drive in battery-powered HMI modules. The device leverages Microchip's eXtreme Low-Power (XLP) architecture with multiple power-managed modes, core-independent peripherals (CIPs) that offload tasks from the CPU, and intelligent analog that performs signal conditioning without waking the core. The result is a deep-sleep current typically below 100 nA with RTCC running, ideal for energy-harvesting or multi-year battery installations. Typical applications include battery-powered LCD consumer devices, IoT sensor nodes with display, white-goods user interfaces, medical glucose and infusion meters, industrial HMI panels, and home-automation thermostats. The on-chip RTCC and LCD charge pump together remove the need for external RTC chips and discrete bias networks, reducing BOM cost and PCB area. When designing with the PIC16F19176-I/P, decouple VDD with a 100 nF ceramic capacitor placed within 5 mm of the pins, and ensure the ICSP programming pins (ICSPCLK/ICSPDAT) are accessible for in-circuit programming. Choose the LCD charge-pump voltage carefully to balance display contrast with sleep-mode current budget. This page consolidates distributor pricing, cross-brand drop-in alternatives, application examples, and design notes that go beyond the manufacturer datasheet, giving procurement and engineering teams a single decision-ready reference.

RFQ संपर्क
PIC16F19176-I/PT - 28KB Flash 8-bit LCD MCU | Microchip
PIC16F19176-I/PT

PIC16F19176-I/PT - 28KB Flash 8-bit LCD MCU | Microchip

The Microchip Technology PIC16F19176-I/PT is an 8-bit PIC microcontroller from the PIC16F19XX family, featuring 28KB (16K x 14 words) of Flash program memory, 2KB RAM, and 256 bytes of EEPROM, housed in a 44-pin TQFP (10x10 mm) package. It operates up to 32MHz and integrates an integrated LCD driver, making it especially suited for battery-powered LCD applications due to an integrated charge pump, high-current I/O pins, and eXtreme Low-Power (XLP) technology. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and programmable peripherals into one package. The PIC16F19176 belongs to the 8-bit RISC PIC family within Microchip's microcontroller hierarchy (8-bit MCU -> PIC16 -> PIC16F19XX), targeting low-power LCD-driven embedded designs with rich Core Independent Peripherals (CIPs) such as CWG, SMT, ZCD, and PPS. Key features include 12-bit ADC2 with computation, 5-bit DAC, low-power comparators, PWM/CCP/CWG/SMT/ZCD/PPS, Real-Time Clock/Calendar (RTCC), and an integrated charge pump that supports LCD bias generation directly from a single Li-ion battery. The device supports 2.3V-5.5V operation across an industrial -40C to +85C temperature range, with nanoWatt XLP sleep currents below 60 nA typical. Architecturally, the PIC16F19176 uses a modified Harvard RISC core with a 14-bit instruction word and 32-level hardware stack. The device integrates Intelligent Analog peripherals and CIPs that execute logic without CPU intervention, freeing the core for power management and user tasks. The LCD driver supports up to 8 common planes and works with the integrated charge pump, eliminating the need for an external bias-boost circuit in single-cell battery designs. Typical applications include battery-powered blood glucose meters and other medical LCD instruments, industrial HMI panels with segment displays, smart thermostats, portable consumer electronics with always-on LCDs, IoT sensor nodes with visual readouts, and metering/utility end equipment requiring long battery life combined with a user-visible LCD. When designing with this part, ensure that segment and common pin allocation is mapped through the PPS (Peripheral Pin Select) and LCD register configuration, and verify charge-pump capacitor values from the manufacturer datasheet. For sleep-mode designs, the RTCC with its dedicated 32 kHz crystal domain and the Low-Power Sleep mode typically extend battery life into multi-year ranges on a single CR2032. This page synthesizes Microchip distributor pricing, drop-in alternatives within the PIC16F19XX family, and practical design notes not found in the manufacturer datasheet alone.

RFQ संपर्क
PIC16F19176T-I/MV - 8-Bit XLP MCU, 28KB Flash, LCD, UQFN-40 | Microchip
PIC16F19176T-I/MV

PIC16F19176T-I/MV - 8-Bit XLP MCU, 28KB Flash, LCD, UQFN-40 | Microchip

The Microchip Technology PIC16F19176T-I/MV is an 8-bit PIC® XLP™ 16F microcontroller IC running at 32 MHz with 28 KB (16K x 14) of Flash program memory, packaged in a 40-pin UQFN (5x5) surface-mount module with exposed thermal pad. It integrates 2 KB SRAM, 256 bytes of EEPROM, and a comprehensive peripheral set tailored for ultra-low-power battery applications with LCD interfaces. What is an 8-bit microcontroller? An 8-bit microcontroller is a single-chip computer that processes data in 8-bit chunks and integrates a CPU, memory, and peripherals on one die. PIC® microcontrollers from Microchip use a modified Harvard RISC architecture. The XLP™ (eXtreme Low Power) family targets battery-powered applications with deep-sleep currents measured in nanoamperes. Microcontrollers in this class sit hierarchically under: MCU -> embedded processor -> semiconductor device. Key features include an integrated LCD driver with charge pump, 12-bit ADC2 (Analog-to-Digital Converter) with computation, a 5-bit DAC, low-power comparators, multiple PWM/CCP/CWG/SMT/ZCD peripherals, Peripheral Pin Select (PPS) for flexible signal routing, and a Real-Time Clock/Calendar (RTCC). The XLP architecture delivers sleep currents below 50 nA typical. The device operates across 2.5 V to 5.5 V, supports up to 32 MHz internal oscillator, and offers 36 I/O pins with high-current sink/source capability. On-chip Core Independent Peripherals (CIPs) allow hardware-based state machine control, offloading tasks from the CPU to reduce power and code complexity. Typical applications include battery-powered LCD consumer devices, IoT sensor nodes with displays, smart thermostats, wearable health monitors, and industrial HMI panels. The integrated charge pump and LCD bias generation eliminate external driver circuitry in many designs. Designers should leverage PPS to remap digital peripherals to any I/O, simplifying PCB layout. Place a 0.1 µF decoupling capacitor within 3 mm of each VDD pin and use the integrated charge pump for contrast stability. This page synthesizes XAIPART distributor pricing, parametric drop-in alternatives, and practical low-power design guidance not consolidated in the manufacturer datasheet.

RFQ संपर्क
PIC16F19176T-I/PT - 28KB Flash XLP MCU w/ LCD | Microchip
PIC16F19176T-I/PT

PIC16F19176T-I/PT - 28KB Flash XLP MCU w/ LCD | Microchip

The Microchip Technology PIC16F19176T-I/PT is an 8-bit PIC® XLP™ microcontroller featuring 32 MHz CPU speed, 28 KB (16K x 14) Flash program memory, 2 KB SRAM, and 256 bytes EEPROM, housed in a 44-pin TQFP (10x10 mm) package. It belongs to the PIC16F19155/56/75/76 family that targets battery-powered applications through an integrated LCD charge pump, eXtreme Low-Power (XLP) technology, and high-current I/O for direct segment drive. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals. It sits in the embedded system hierarchy between simple logic ICs and 32-bit application processors: PIC16F19176T-I/PT > 8-bit MCU > microcontroller > integrated circuit > semiconductor. XLP variants extend battery life to months or years through sleep currents under 1 µA and on-chip peripherals that wake the core on demand. Key features include a 12-bit ADC with 2 DAC channels, low-power comparator (LP COMP), PWM, CCP, CWG (Configurable Logic Cell), SMT (Signal Measurement Timer), ZCD (Zero-Cross Detect), PPS (Peripheral Pin Select), and RTCC (Real-Time Clock/Calendar). The integrated LCD driver with charge pump eliminates external bias generation, supporting 4 common x up to 46 segments. PIC16F19176T-I/PT operates across 2.5 V to 5.5 V over the industrial -40 °C to +85 °C range. The device leverages an enhanced mid-range 16-bit instruction set with 14-bit opcodes, providing deterministic interrupt latency. Hardware math accelerators and CLC cells offload logic from the CPU, while Core Independent Peripherals let tasks run without waking the core. PPS allows post-build pin remapping, easing PCB layout changes late in development. Typical applications include battery-powered metering with LCD readout, e-paper / segment LCD thermostats, portable medical monitors, IoT sensor nodes with displays, and HVAC controllers. The combination of integrated charge pump and 256-byte EEPROM suits sealed units where firmware parameters must persist without battery backup. For power-sensitive designs, verify the active current at the operating MIPS rate and the deep-sleep current with peripherals disabled. The TQFP-44 package supports hand-solderable prototyping; production typically uses 100 % reeled T&R. This page combines distributor pricing, drop-in same-family alternatives, and design notes not always present in the manufacturer datasheet, providing a single engineering reference for PIC16F19176T-I/PT selection.

RFQ संपर्क
PIC16F19185-E/PT - 14KB Flash LCD MCU 48-TQFP | Microchip
PIC16F19185-E/PT

PIC16F19185-E/PT - 14KB Flash LCD MCU 48-TQFP | Microchip

The Microchip Technology PIC16F19185-E/PT is an 8-bit PIC® XLP™ microcontroller featuring 14KB Flash, 1KB SRAM, and 256B EEPROM in a 48-pin TQFP (7x7 mm) package with integrated LCD driver, 12-bit ADC2, 5-bit DAC, low-power comparator, PWM, CCP, CWG, SMT, ZCD, PPS, and RTCC. It runs at 32 MHz and operates across 2.3V to 5.5V. An 8-bit microcontroller is a small computer-on-a-chip built around an 8-bit data path, executing one byte per instruction cycle. PIC microcontrollers sit in the broader hierarchy of microcontrollers -> embedded computing -> semiconductor ICs, and the PIC16F19185 belongs to the PIC16F1 enhanced mid-range family, which targets ultra-low-power (XLP) battery applications with Core Independent Peripherals (CIPs) that offload tasks from the CPU. Key features include eXtreme Low-Power (XLP) technology with nanoWatt XLP sleep currents, an integrated LCD charge pump that supports displays up to 5V without external boost components, 12-bit ADC2 with computation, zero-cross detect (ZCD) for triac control, signal measurement timer (SMT), and configurable logic cells (CLC). High-current I/O pins capable of sourcing/sinking 100 mA directly drive LEDs and relays, reducing external driver cost and PCB area. The architecture pairs an enhanced mid-range 8-bit core with intelligent analog peripherals and Core Independent Peripherals, allowing autonomous operation of PWM, ADC, and CWG without CPU intervention. This dual approach reduces firmware complexity, lowers active-mode power, and lets the CPU remain in sleep for longer windows, which is critical for battery lifetime and IEC 62368-1 standby compliance. Typical applications include battery-powered LCD consumer devices, home-automation sensor panels, IoT edge nodes with displays, industrial HMI controls, and metering/timer subsystems. The integrated LCD charge pump and 100 mA I/O make it especially suited to thermostat-style products and appliance front panels. When designing, ensure the MCU's VDD range (2.3V to 5.5V) covers battery end-of-life voltage. Decouple VDD with 100 nF and 10 uF ceramics close to the pins, and route the LCD charge-pump capacitors within 5 mm of the dedicated pins to minimize ripple on VLCD. This page combines distributor pricing, same-package drop-in alternatives, and practical design notes that supplement the Microchip datasheet and family data brief.

RFQ संपर्क
PIC16F19185T-I/MV - 8-Bit XLP LCD MCU, 14KB Flash, 48-UQFN | Microchip
PIC16F19185T-I/MV

PIC16F19185T-I/MV - 8-Bit XLP LCD MCU, 14KB Flash, 48-UQFN | Microchip

The Microchip Technology PIC16F19185T-I/MV is an 8-bit PIC microcontroller from the PIC16F family, featuring 14KB (8K x 14) of Flash program memory and operating at up to 32 MHz, housed in a 48-pin UQFN (6x6 mm) package with exposed pad. The device integrates 1KB of SRAM, 256 bytes of EEPROM, and 43 user I/O pins, supporting operating voltages from 2.3V to 5.5V. An MCU (microcontroller) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O onto one die. 8-bit microcontrollers like the PIC16F19185 sit at the bottom of the embedded computing hierarchy - below 16-bit DSPIC parts, 32-bit Cortex-M devices, and application processors. They are optimized for deterministic, low-power, cost-sensitive tasks such as user-interface control, sensor conditioning, and battery-driven LCD appliances, where a full RTOS is unnecessary and pin/cycle budgets matter. Key features include Microchip's eXtreme Low-Power (XLP) technology with integrated LCD drive support, a 12-bit ADC2, a 5-bit DAC, low-power comparator (LP COMP), PWM, CCP, CWG, SMT (Signal Measurement Timer), ZCD (Zero-Cross Detect), PPS (Peripheral Pin Select), and a Real-Time Clock/Calendar (RTCC). An integrated charge pump and high-current I/O enable direct LCD backlight drive from battery sources. The 48-UQFN exposed pad package supports compact PCB layouts and improved thermal dissipation. The architecture combines a RISC-style PIC16 core with Core Independent Peripherals (CIPs) and Intelligent Analog, allowing functions like waveform generation, signal measurement, and LCD segment drive to run without CPU intervention. PPS provides flexible pin assignments, reducing layout constraints in densely-routed designs. Typical applications include battery-powered LCD thermostats, portable medical monitors, IoT sensor hubs with character displays, white-goods control panels, industrial HMI modules, and metering devices requiring long battery life. The wide operating voltage (2.3-5.5V) supports direct connection to 2xAA, 3xAA, or lithium battery stacks. When designing with this MCU, ensure the exposed pad is soldered to a sufficiently large copper pour for thermal performance. The PPS feature allows most peripherals to be mapped to a wide range of I/O pins, simplifying PCB layout. For lowest power, use XLP sleep modes with RTCC wake-up. This page synthesizes distributor pricing from DigiKey/Mouser, drop-in alternatives from Microchip's same-family portfolio, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
PIC16F19185T-I/PT - 14KB Flash 8-bit XLP MCU | Microchip
PIC16F19185T-I/PT

PIC16F19185T-I/PT - 14KB Flash 8-bit XLP MCU | Microchip

The Microchip Technology PIC16F19185T-I/PT is an 8-bit PIC RISC microcontroller with 14KB Flash, 1KB RAM, and a 32 MHz CPU core, offered in a 48-pin TQFP (7x7 mm) package. It targets battery-powered applications that require on-chip LCD drive, an integrated charge pump, and Core Independent Peripherals (CIPs) such as CLC, NCO, and configurable logic. The 'T' suffix indicates Tape & Reel packaging, while the 'I' industrial temperature grade covers -40C to +85C operation at 3.0V-5.5V. A PIC microcontroller (Programmable Interface Controller) is a Harvard-architecture 8-bit RISC MCU family from Microchip, used in embedded control from simple timer loops to complex battery-powered instruments. The PIC16F19185 belongs to the PIC16F1 enhanced mid-range family, positioned between baseline PIC10/12/16 and the higher-end PIC18F/dsPIC33 lines. Within Microchip's product hierarchy, this device is classified as an MCU -> 8-bit MCU -> PIC16 family -> PIC16F191xx sub-family, targeting ultra-low-power LCD applications that combine eXtreme Low-Power (XLP) technology with intelligent analog and configurable logic. Key features include a Charge Time Measurement Unit (CTMU), a 12-bit ADC with computation (ADC2), up to 43 high-current I/O capable of 50 mA source/sink for direct LED drive, hardware Capacitive Touch support, and an integrated LCD driver with charge pump that can bias glass even from a single-cell Li-ion supply. The device provides multiple power-managed operating modes (RUN, DOZE, IDLE, SLEEP) with sub-uA SLEEP current and a rapid wake-up time. Architecturally, the PIC16F19185 uses a 14-bit instruction word with a 16-level hardware stack and an 8-bit data path, backed by the NanoWatt XLP power management block. The 14KB Flash (8K x 14) supports self-programming, and 1KB SRAM plus 256B data EEPROM provides ample storage for sensor calibration, LCD segment maps, and user settings. Typical applications include battery-powered LCD thermostats, low-power sensor hubs with on-glass display, water/gas meters with integrated charge pump, capacitive-touch control panels with LCD feedback, and portable medical monitoring devices that require long battery life and visual feedback. When designing with this device, choose the -I industrial grade for commercial products and -E extended grade for harsher environments. Ensure decoupling follows the Microchip PICDEM and Curiosity HPC kit reference layouts, and that the charge pump capacitors match the LCD glass specifications. This page synthesizes distributor pricing, drop-in package-compatible alternatives within the PIC16F191xx family, and practical design notes sourced from the Microchip PIC16F19185 datasheet and product brief, not found on a single distributor page.

RFQ संपर्क