माइक्रोकंट्रोलर्स

उत्पाद (19,000+)

Z84C00 - CMOS Z80 8-Bit CPU Microprocessor | Zilog
Z84C00

Z84C00 - CMOS Z80 8-Bit CPU Microprocessor | Zilog

The Zilog Z84C00 is a CMOS Z80 8-bit central processing unit (CPU) microprocessor available in speed grades of 6 MHz, 8 MHz, 10 MHz, and 20 MHz, executing 158 instructions with software compatibility to the Intel 8080A, housed in 40-pin DIP, 44-pin PLCC, or 44-pin QFP packages. A microprocessor (CPU) is the core computation and control block of a computer or embedded system, executing stored instructions and coordinating memory and peripheral I/O. The Z80 family sits within the 8-bit microprocessor hierarchy, which in turn belongs to the broader semiconductor category of embedded processors. First released by Zilog in 1976, the Z80 became one of the most widely deployed CPUs of the early personal computing era. Key features of the Z84C00 include its extensive 158-instruction set (including 8080A-compatible instructions plus indexed, block, and bit instructions), dual register file with alternate registers for fast context switching, on-chip dynamic RAM refresh counter, and a single 5V supply. The CMOS process delivers significantly lower power consumption than the original NMOS Z8400, making it suitable for battery-powered and industrial systems. Technically, the Z84C00 is a fourth-generation enhanced microprocessor offering higher system throughput and more efficient memory utilization than second- and third-generation processors, according to the Zilog Z8400/Z84C00 datasheet. It provides 16-bit address bus capability for up to 64 KB of memory addressing, interrupt modes 0, 1, and 2, a non-maskable interrupt (NMI) input, and WAIT states for slow memory. Typical applications include retro-computing repairs and reproductions (ZX Spectrum, MSX, RC2014 kits), industrial control and instrumentation, embedded controllers, and educational platforms. Its decades-long software ecosystem makes it a natural fit for legacy system maintenance. Design consideration: verify the speed-grade suffix (06, 08, 10, 20) against your clock source, and note the Z84C00 family was officially discontinued by Zilog with last orders in June 2024, so plan lifecycle sourcing accordingly. This page synthesizes distributor availability data, drop-in same-family alternatives, and lifecycle guidance not found in the manufacturer datasheet.

RFQ संपर्क
Z84C0010FEC - 10MHz CMOS Z80 CPU, 44-LQFP | Zilog
Z84C0010FEC

Z84C0010FEC - 10MHz CMOS Z80 CPU, 44-LQFP | Zilog

The Zilog Z84C0010FEC is a CMOS Z80 8-bit microprocessor (CPU) core operating at clock speeds up to 10 MHz, housed in a 44-pin LQFP (10 x 10 mm) surface-mount package. As a member of the Z84C00 family, it delivers the classic Z80 architecture in a low-power CMOS process. A microprocessor is the central processing unit (CPU) of a computing system, responsible for executing program instructions, performing arithmetic and logic operations, and controlling memory and peripheral access. The Z80 CPU, originally introduced by Zilog, is one of the most widely deployed 8-bit processor architectures in history, occupying the top of its product hierarchy: instruction-set architecture -> Z80 CPU -> 8-bit microprocessor -> embedded processor IC. Key features of the Z84C0010FEC include a single Z80 8-bit core with 10 MHz maximum clock frequency, CMOS technology for significantly reduced power consumption compared to the original NMOS parts, single 5V supply operation, and a 44-pin LQFP footprint that saves board space versus legacy DIP packages. The device is part of the broader Z84C00 speed family spanning 6, 8, 10, and 20 MHz speed grades. Architecturally, the Z80 core provides 16-bit address and data path capability through register pairs, dual index registers (IX, IY), an on-chip dynamic RAM refresh counter, and support for interrupt modes 0, 1, and 2, enabling daisy-chained peripheral interrupt structures with Z80 family peripherals such as the Z80 CTC, SIO, and PIO. Typical applications include legacy industrial control systems, embedded retro-computing and hobbyist designs, telecom line cards, and maintenance replacement of CPU silicon in long-life equipment where software compatibility with the Z80 instruction set must be preserved. Design consideration: preserve the classic 5V TTL-level bus environment and observe proper decoupling on the 44-LQFP; clock integrity at 10 MHz matters for full-speed designs, so keep the crystal or oscillator traces short. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.

RFQ संपर्क
Z84C0020PEC - 20 MHz Z80 CMOS CPU | Zilog | DIP-40
Z84C0020PEC

Z84C0020PEC - 20 MHz Z80 CMOS CPU | Zilog | DIP-40

Zilog Z84C0020PEC is an 8-bit CMOS Z80 central processing unit operating at 20 MHz in a 40-pin PDIP package. The verified distributor data identifies one core, a 20 MHz clock, and 40-pin PDIP construction. The family datasheet identifies the device as part of the enhanced Z8400/Z84C00 processor family, whose internal register set contains 208 bits and whose architecture supports efficient memory utilization and software migration. A microprocessor is the central control element of a computer or embedded controller, fetching instructions, decoding operations, and coordinating memory and peripheral access. The Z80 belongs to the 8-bit microprocessor class and extends the earlier Z80 architecture through enhanced processing capability. Within the broader electronics hierarchy, it is a CMOS microprocessor IC rather than a microcontroller: external memory, clocking, reset, interrupt, and peripheral circuitry remain part of the surrounding system design. The most important verified specifications are the 8-bit CPU architecture, 20 MHz operating frequency, single-core configuration, CMOS technology, and PDIP-40 package. Zilog describes speed offerings across the broader family from 6 MHz through 20 MHz. The manufacturer documentation states that the processor family provides improved system throughput and more efficient memory utilization than comparable earlier-generation processors while retaining software-migration support. Z84C0020PEC is suitable for legacy Z80 systems, industrial controllers, educational platforms, embedded instruments, and retro-computing designs that specifically require this processor and package. Its parallel CPU architecture remains useful for systems built around Z80 memory, interrupt, and peripheral conventions. Because it is a microprocessor rather than a self-contained microcontroller, designers must provide the required external system components and verify timing, bus loading, and software compatibility. A critical hardware requirement is confirmation of the complete operating voltage, temperature grade, pinout, timing, and electrical limits from the manufacturer datasheet for the exact ordering code. The suffix PEC is associated with the listed 40-pin PDIP device, but package and suffix details should not be inferred beyond the supplied data when purchasing or redesigning. This page consolidates verified distributor identification, manufacturer family documentation, sourcing links, and practical replacement guidance. It also distinguishes true same-footprint drop-in candidates from alternatives that are merely functionally similar but would require board changes, preventing an incompatible substitution from being presented as a safe replacement.

RFQ संपर्क
Z8673312PSG - 8-Bit 12MHz 8KB OTP Microcontroller | Zilog
Z8673312PSG

Z8673312PSG - 8-Bit 12MHz 8KB OTP Microcontroller | Zilog

Zilog Z8673312PSG is an 8-bit Z8 CMOS microcontroller operating at up to 12 MHz with 8 KB of one-time-programmable memory, supplied in a 28-pin DIP package. The verified distributor listings identify the device as a Z8 Z8 microcontroller with 8K x 8 OTP memory and a 12 MHz clock. Its architecture sits within the hierarchy of microcontrollers, embedded processors, and general-purpose semiconductor ICs. An 8-bit microcontroller is a compact embedded controller designed to execute instructions from a fixed program memory and interface with sensors, switches, indicators, communications circuits, and other peripherals. One-time-programmable memory is intended for final firmware versions that do not need repeated field updates, while the 12 MHz operating rate provides the execution headroom required by typical control and monitoring tasks. The principal verified characteristics are an 8-bit processor architecture, 12 MHz maximum operating frequency, 8 KB of OTP program memory organized as 8K x 8, CMOS construction, and a 28-pin DIP package. The DIP format supports conventional PCB insertion and prototyping workflows. The listing also identifies the product with the Z8 family, placing it in Zilog's established embedded-controller product line. The device's architecture is relevant for cost-sensitive embedded systems where deterministic firmware execution, compact logic integration, and one-time-programmable storage are more important than flash reprogrammability. A datasheet provides the authoritative pin, electrical, timing, and environmental limits. Those details were not reproduced in the supplied verification snippets and should therefore be checked before final schematic, clock, and reset design work. Typical design uses include simple industrial control panels, appliance controllers, small sensor-hub nodes, LED sequencing modules, and embedded timing or event-control systems. The 12 MHz clock and 8 KB OTP memory are sufficient for focused firmware that reads inputs, executes control logic, and drives outputs without requiring a high-performance processor or external program-memory device. Designers should treat the 28-pin DIP footprint and 8 KB OTP limit as fixed constraints. Firmware size must be checked against the available program memory before production programming because OTP devices cannot be conventionally reflashed. Decoupling, reset, oscillator, and unused-pin handling should follow the manufacturer datasheet rather than generic MCU assumptions. This product data consolidates verified distributor descriptions, package information, datasheet access, and same-family alternatives. It also distinguishes published facts from unavailable details, allowing engineers to evaluate sourcing and replacement options without mistaking unsupported electrical, environmental, lifecycle, or pricing claims for manufacturer specifications.

RFQ संपर्क
Z8674312PSG - 8-Bit 12MHz OTP Microcontroller | Zilog
Z8674312PSG

Z8674312PSG - 8-Bit 12MHz OTP Microcontroller | Zilog

The Zilog Z8674312PSG is an 8-bit Z8 Z86-family microcontroller with 8 KB of one-time-programmable program memory, 236 x 8 bytes of RAM, a 12 MHz maximum operating frequency, and 32 general-purpose I/O pins in a 40-pin PDIP package. A microcontroller is a programmable semiconductor that integrates a CPU core, nonvolatile program memory, data memory, I/O ports, and peripherals on one device. The Z8674312PSG belongs to the Z8 microcontrollers family within the broader embedded-controller and semiconductor hierarchy. Its OTP program memory permits a finished device to be programmed once, making it suitable for cost-sensitive products that do not require in-circuit firmware updates. The principal device characteristics include an 8 KB (8K x 8) OTP program-memory capacity, 236 x 8 bytes of RAM, and a maximum clock frequency of 12 MHz. The device provides 32 general-purpose I/O pins, a Z8 processor core, EBI/EMI connectivity, power-on reset, and a watchdog timer. These features provide a practical combination of control logic, data storage, and peripheral integration for embedded products. The 12 MHz operating limit should be treated as the timing ceiling for the complete design, including clock tolerance, peripheral timing, and interrupt-service requirements. Its 8 KB OTP memory is suitable for compact control firmware, but memory utilization must be checked after including the startup code, drivers, interrupt routines, and application logic. The 236-byte RAM area also requires attention when buffering data or maintaining multiple task stacks. Typical uses include appliance controllers, small industrial control modules, building equipment, instrumentation, simple human-interface panels, and embedded automation products. For a new design, engineers should confirm oscillator requirements, available I/O, memory consumption, timing margins, and interrupt behavior against the complete Zilog datasheet before committing the 40-pin footprint. The main design consideration is that OTP memory cannot be erased and rewritten in the field. Firmware validation must therefore occur before final programming, while power, ground, and decoupling layout must follow the electrical requirements published for this device family. This page consolidates verified distributor specifications, procurement details, package information, application guidance, and design cautions into a compact engineering reference that helps distinguish this Z8 microcontroller from broader embedded processor families.

RFQ संपर्क
Z86C9116FEC - 16MHz 8-Bit ROMless MCU | Zilog | Embedded Control
Z86C9116FEC

Z86C9116FEC - 16MHz 8-Bit ROMless MCU | Zilog | Embedded Control

The Zilog Z86C9116FEC is an 8-bit Z8 ROMless microcontroller operating at 16MHz, with 236 bytes of RAM, 32 I/O lines, two 8-bit timers, and a UART interface in a 44-LQFP package measuring 10mm by 10mm. The device is designed for embedded control applications that require external program memory and a compact, surface-mount microcontroller package. A ROMless microcontroller is an 8-bit microcontroller that does not contain its application program in internal ROM. It must be paired with an external memory device, which gives the system designer flexibility to select program capacity independently of the MCU. In the product hierarchy, Z86C9116FEC belongs to the Z8 family of ROMless microcontrollers and provides a straightforward architecture for small embedded controllers. The principal features of this device include a 16MHz operating frequency, 236 bytes of on-chip RAM, 32 general-purpose I/O lines, two 8-bit timer blocks, and one UART communication interface. Its ROMless architecture makes it appropriate when firmware changes are expected, when program storage requirements vary between products, or when a common external flash configuration is desired across multiple controller variants. The Z8 architecture provides an 8-bit processing path optimized for embedded control tasks rather than high-throughput computing. Combined with 32 I/O lines, the device can directly support digital inputs, outputs, control signals, and peripheral interfaces. The two 8-bit timers support timing and event-counting duties, while the UART provides a serial channel for connecting the controller to a host, sensor assembly, or communication module. Typical design opportunities include programmable logic controllers, appliance controllers, building-control modules, motor-sequence controllers, industrial interface modules, and compact embedded automation products. Its 44-LQFP package provides a practical pin count for systems requiring numerous external connections while remaining compatible with standard surface-mount assembly and inspection processes. A key design consideration is that the ROMless device requires suitable external program memory and a correctly designed bus interface. Designers should also confirm the available operating voltage, clock configuration, peripheral pin assignments, and memory interface requirements against the current Zilog datasheet before finalizing the schematic or PCB layout. This product page consolidates the verified distributor specifications, package information, pricing availability, cross-reference evidence, and design considerations for Z86C9116FEC. It also distinguishes confirmed drop-in replacements from merely similar controllers, helping engineers avoid selecting a 44-LQFP part whose pinout or architecture is not actually compatible.

RFQ संपर्क
Z86C9116FEG - 16MHz ROMless 8-Bit MCU | Zilog | Industrial
Z86C9116FEG

Z86C9116FEG - 16MHz ROMless 8-Bit MCU | Zilog | Industrial

The Zilog Z86C9116FEG is an 8-bit Z8 ROMless microcontroller operating at 16 MHz, with 236 x 8 bytes of RAM, 24 general-purpose I/O pins, and UART/USART connectivity in a 44-LQFP 10 x 10 mm surface-mount package. Its 4.5 V to 5.5 V supply range and -40°C to +105°C industrial temperature range suit embedded control systems requiring compact, deterministic communications and general-purpose I/O. The Z86C9116FEG is designed for applications that require external program memory while retaining a compact 8-bit control architecture. What is an 8-bit ROMless microcontroller? A ROMless microcontroller is a programmable embedded controller that does not contain its own program memory. Instead, the application program is stored in external memory, such as an external ROM or nonvolatile memory. This makes ROMless devices useful when the firmware must be large, frequently updated, or separately managed. The Z8 family combines an 8-bit CPU, general-purpose I/O, timers, serial communication, and external-memory interfacing in a single device. The Z86C9116FEG provides a 16 MHz operating frequency, 236 x 8 bytes of internal RAM, 24 general-purpose I/O pins, and UART/USART connectivity. Its 44-LQFP package exposes 44 leads and is intended for surface-mount PCB assembly. The 4.5 V minimum operating voltage and 5.5 V maximum operating voltage are important constraints for systems using 5 V logic. The industrial temperature range supports use in factory equipment, industrial controllers, instrumentation, and other embedded applications where consumer-temperature components may be unsuitable. The ROMless architecture separates code execution from program storage and allows the designer to select the external memory device based on code size, programming requirements, or field-update strategy. The 16 MHz clock rate provides a balance between processing throughput, power consumption, and system design simplicity for 8-bit control tasks. UART/USART support allows the controller to communicate with sensors, host systems, converters, or other embedded modules. Typical uses include industrial automation modules, serial protocol bridges, keypad and display controllers, appliance control boards, motor-control supervisory circuits, and compact embedded instruments. The 24 available I/O pins can support digital inputs, outputs, control signals, status indicators, and external interface functions when the application does not require all pins for specialized peripheral functions. Designers should verify the external-memory interface, oscillator requirements, decoupling, and the complete 44-pin signal map against the manufacturer datasheet before layout. Because the provided source data does not publish a verified pinout or pricing table, those details remain explicitly marked as unavailable in the technical records. This page combines verified distributor specifications, package information, application guidance, and purchasing considerations for engineers evaluating the Z86C9116FEG.

RFQ संपर्क
Z86C9116FSC 16MHz ROMless 8-Bit MCU | Zilog
Z86C9116FSC

Z86C9116FSC 16MHz ROMless 8-Bit MCU | Zilog

Zilog Z86C9116FSC is an 8-bit ROMless Z8 microcontroller operating at 16 MHz and packaged in a 44-pin LQFP measuring 10 mm by 10 mm. It provides 236 bytes of RAM, 32 I/O pins, two 8-bit timers, and a UART interface. The device combines a compact 8-bit embedded-control architecture with external program-memory support, making it suitable for cost-sensitive control systems that require dedicated application firmware. An 8-bit microcontroller is a microprocessor core, memory interface, and peripheral set integrated on one semiconductor die. The Z8 family belongs to the broader microcontroller and embedded-controller hierarchy, where firmware controls sensors, relays, user interfaces, communications, and power functions. Unlike a ROM-based device, the ROMless Z86C9116FSC requires an external program-memory device, allowing the program capacity and interface arrangement to be selected according to the finished system. The verified product information identifies a 16 MHz operating speed, 236 bytes of RAM, 32 I/O pins, two 8-bit timers, and one UART interface. These resources support basic sequential control, periodic timing, serial communication, and digital input/output tasks. The 44-LQFP package provides 44 physical leads for power, ground, clock, reset, programming, I/O, and external-memory connections, although exact lead assignments are not included in the supplied source data. The ROMless architecture is the principal engineering distinction of this Z8 device. External program memory allows firmware capacity to scale with the application, but the PCB must also provide the external memory interface, address and data routing, and associated signal-integrity measures. Designers should therefore evaluate the complete memory subsystem rather than treating the microcontroller package as a self-contained storage solution. Typical uses include small industrial controllers, appliance-control boards, keypad interfaces, communication modules, motor or relay sequencers, and compact embedded products that benefit from the Z8 instruction set and dedicated timers. External program memory is appropriate when a fixed application program must be loaded during manufacturing rather than stored in an internal ROM mask. A primary design consideration is package and memory-interface validation. Confirm the exact Z86C9116FSC pin assignment, external-memory requirements, clock configuration, and programming connection against the manufacturer documentation before layout release. Because the available verified data does not include a complete pinout or numerical distributor price schedule, those details remain explicitly unresolved rather than being inferred. This product page consolidates the verified distributor specifications, purchasing sources, package information, and engineering guidance for the Z86C9116FSC. It also distinguishes verified facts from missing electrical, pinout, pricing, and lifecycle details, helping engineers assess fit before committing to a PCB design or production order.

RFQ संपर्क
Z86C9116PSG - 16MHz 8-Bit ROMless MCU | Zilog
Z86C9116PSG

Z86C9116PSG - 16MHz 8-Bit ROMless MCU | Zilog

Zilog Z86C9116PSG is an 8-bit Z8 ROMless microcontroller operating at 16 MHz with a 4.5 V to 5.5 V supply range, 236 bytes of RAM, 32 I/O ports, and a 40-pin PDIP package. It belongs to the Z86C91 product family and requires an external program-memory device because no internal ROM is provided. An 8-bit ROMless microcontroller is a compact embedded-control processor designed for systems that require deterministic I/O handling rather than application storage inside the MCU. In the product hierarchy, the Z86C9116PSG is a microcontroller, an embedded processor, and a semiconductor integrated circuit. Its ROMless architecture separates program memory from the controller, allowing designers to select external storage according to firmware size and interface requirements. The headline features include a 16 MHz operating clock, an 8-bit data bus, 236 bytes of on-chip RAM, and 32 I/O ports. The 4.5 V to 5.5 V supply range supports conventional 5 V industrial embedded systems. Because the MCU is ROMless, an external program-memory device is required, while the 236 bytes of internal RAM provide limited working memory for variables, stack operations, and control-state management. The Z86C9116PSG uses the Z8 architecture and is positioned as a compact, low-cost controller for embedded products requiring parallel digital I/O. Its 40-pin PDIP package provides a comparatively large number of external connections compared with smaller surface-mount MCUs, making it practical for prototyping, through-hole industrial assemblies, and applications that need direct access to peripheral pins. Typical uses include appliance controllers, industrial sequencers, keyboard or panel interfaces, lighting-control modules, instrumentation, and small embedded automation systems. The 32 I/O ports are particularly useful when a design must connect multiple switches, indicators, sensors, or actuators without relying on additional interface expanders. When designing around this device, engineers must account for the absence of internal program memory and provide a suitable external memory implementation. The available verified data does not specify the external-memory interface, exact pin assignments, peripheral mix, or detailed timing characteristics, so those items should be confirmed in the manufacturer datasheet before schematic capture. This product page consolidates distributor availability, verified pricing, device hierarchy, package information, and same-brand replacement analysis. It also distinguishes directly documented drop-in candidates from alternatives that cannot be verified as pin-to-pin compatible, helping engineers avoid replacing an MCU solely because the clock speed and package description look similar.

RFQ संपर्क
Z86C9320FSC 8-Bit 20MHz ROMless MCU 44-LQFP | Zilog
Z86C9320FSC

Z86C9320FSC 8-Bit 20MHz ROMless MCU 44-LQFP | Zilog

The Zilog Z86C9320FSC is an 8-bit Z8 ROMless microcontroller operating at up to 20 MHz in a 44-LQFP package measuring 10 x 10 mm. It provides 236 KB of RAM, 24 I/O pins, three 8-bit timers, and a UART communication interface. Z86C9320FSC is intended for embedded control designs where external program memory is required and a compact, high-pin-count surface-mount implementation is preferred. An 8-bit microcontroller is a programmable semiconductor device designed to execute embedded control logic using an 8-bit data path. The Z86C9320FSC belongs to the Z8 family of Zilog microcontrollers and is a ROMless device, meaning the application program is stored in external memory rather than embedded program ROM. This architecture separates the controller from the program memory, allowing the memory device to be selected according to application capacity, interface, and cost requirements. The principal verified specifications are a maximum operating speed of 20 MHz, 236 KB of RAM, 24 I/O, three 8-bit timers, one UART interface, and a 44-LQFP package. The package provides 44 terminals for power, clock, reset, communications, timers, interrupts, general-purpose I/O, and external-memory connections. The reported speed options include 20 MHz, 25 MHz, and 33 MHz, while the distributor listing identifies the Z86C9320FSC specifically as a 20 MHz ROMless device. The ROMless architecture is useful for applications that need larger or field-updatable firmware than a fixed-program microcontroller normally provides. External program-memory selection must account for bus timing, address capacity, signal integrity, and the controller's documented external-memory interface. The Z86C9320FSC should therefore be evaluated as a system component rather than only as a standalone MCU. Typical application areas include industrial control panels, serial-control equipment, building automation modules, data-acquisition controllers, motor-control interfaces, and embedded communication products. A UART provides a practical path for host configuration, sensor networking, or supervisory control, while the three timers support periodic timing, input capture, or basic output-control functions depending on the complete peripheral configuration. A critical design consideration is firmware availability: because this device is ROMless, the PCB must include an appropriate external memory solution and correct bus support components. Engineers should verify the complete Zilog documentation for electrical limits, pin assignments, memory-interface timing, clock requirements, and programming procedure before releasing a production layout. This page consolidates verified distributor specifications, package information, sourcing details, and engineering-oriented application guidance. It also distinguishes documented facts from parameters that require confirmation from the manufacturer datasheet, helping designers compare the Z86C9320FSC efficiently without assuming unavailable electrical details.

RFQ संपर्क
Z86C9333FSC - 33MHz 8-Bit ROMless MCU | Zilog
Z86C9333FSC

Z86C9333FSC - 33MHz 8-Bit ROMless MCU | Zilog

Zilog Z86C9333FSC is a 33 MHz, 8-bit Z8 ROMless microcontroller with 236 x 8 bytes of RAM, 24 I/O lines, three 8-bit timers, UART/USART support, and EBI/EMI connectivity in a 44-pin LQFP package measuring 10 x 10 mm. Its 33 MHz operating speed provides higher throughput than conventional low-speed 8-bit controllers while retaining the simple Z8 architecture and external program-memory interface. An 8-bit microcontroller is a compact processor designed to execute embedded control logic from program memory and maintain operating state in RAM. The Z86C9333 belongs to the broader embedded-controller hierarchy: MCU -> microcontroller -> embedded processor -> semiconductor. A ROMless architecture means the device contains no internal program ROM, so firmware must be supplied through an external memory interface. This architecture is useful when programs, firmware revisions, or memory sizes must remain flexible. The verified feature set includes ROMless operation at 33 MHz, 236 bytes of RAM, 24 I/O lines, three 8-bit timers, UART communication, and EBI/EMI interfaces. The 44-LQFP surface-mount package exposes substantially more signal pins than small dual-inline packages, supporting parallel external memory and additional peripheral connectivity while remaining compatible with automated PCB assembly. The Z86C9333 architecture is intended for embedded control rather than high-compute workloads. Its external program-memory interface allows the stored firmware size to be established outside the MCU, while its three timers support periodic counting, timing, and event generation. UART/USART communication enables connection to host systems, sensors, or other controllers, and EBI/EMI provides an external bus-oriented path for additional devices. Typical applications include industrial keypad controllers, serial data concentrators, instrumentation interfaces, embedded control panels, and compact automation modules. In these systems, the 33 MHz speed can improve response to serial traffic and control tasks, while the 24 I/O lines reduce the need for separate I/O expanders. The ROMless configuration is particularly valuable when the same MCU platform must cover several firmware versions or board configurations. Designers must account for external program-memory timing, address decoding, bus contention, and required support components when using the ROMless configuration. PCB layout should minimize routing delay and preserve signal integrity on external bus and UART lines. Software must also provide the vector table and reset behavior expected by the external memory system. Because the verified data does not state supply voltage, timing margins, or detailed pin assignments, those values should be confirmed in the manufacturer documentation before schematic capture. This product page consolidates verified distributor specifications, same-package replacement information, application guidance, and design cautions. It distinguishes confirmed Z86C9333FSC characteristics from unavailable electrical details so procurement and engineering decisions can be made without inventing package, pin, or lifecycle information.

RFQ संपर्क
Z86E0812PEG - 8-Bit 12MHz OTP Microcontroller | Zilog
Z86E0812PEG

Z86E0812PEG - 8-Bit 12MHz OTP Microcontroller | Zilog

Zilog Z86E0812PEG is an 8-bit Z8 microcontroller operating at up to 12 MHz, with 2 KB of one-time-programmable memory, 14 I/O ports, a 4.5 V to 5.5 V supply range, and an 18-pin PDIP package. It is designed for compact embedded-control systems requiring straightforward 8-bit processing, dedicated I/O, and firmware retention without a separate external memory device. An 8-bit microcontroller is a programmable semiconductor containing a processor core, memory, I/O ports, and supporting peripherals on one integrated circuit. The Zilog Z8 family belongs to the broader embedded-controller hierarchy that includes microcontrollers, embedded processors, and semiconductors. Compared with a general-purpose processor, this device targets smaller control loops where cost, simplicity, deterministic peripheral access, and board area are more important than complex computation or high memory bandwidth. Key verified specifications include a 12 MHz maximum clock speed, 2 KB of OTP program memory, 14 I/O ports, and a 4.5 V to 5.5 V operating supply range. Its operating temperature spans -40°C to +105°C, making it suitable for industrial-temperature equipment when the associated system design and qualification requirements are satisfied. The RoHS designation identifies the part as compliant with the supplied RoHS listing, while other regulatory classifications remain unconfirmed in the available data. The device uses the Z8 architecture described in the available product listings as an eZ8 CISC microcontroller. One-time-programmable memory is intended for firmware that does not require later field rewriting, helping control production complexity when the final program is known before deployment. The 14 I/O pins provide interfaces for digital inputs, output control, or mixed peripheral functions, while the 18-pin PDIP format supports conventional through-hole assembly and prototyping. Typical applications include small industrial controllers, sensor-interface modules, building-control products, appliance-control boards, and compact embedded instruments. The 12 MHz clock is appropriate for moderate-speed digital sequencing, while the 14 available I/O ports can connect switches, indicators, relays, and discrete sensing components. Because the part has 2 KB of OTP rather than large RAM or Flash, firmware should be sized carefully and peripheral-heavy tasks delegated to dedicated devices when necessary. The primary design consideration is validating the exact pin assignments, oscillator requirements, reset behavior, and programming procedure against the official manufacturer documentation before layout release. Designers should also confirm current consumption and timing behavior for the selected external clock and operating conditions, because those values were not established by the supplied verification data. DIP packaging requires adequate insertion clearance, mechanical support, and protection from electrostatic discharge during handling. This product page consolidates verified distributor specifications, lifecycle information, package details, commercial availability links, and practical application guidance. It also distinguishes verified Zilog family drop-in options from unverified cross-brand replacements so engineers can make a sourcing decision without treating general cross-reference tools as proof of pin and firmware compatibility.

RFQ संपर्क
Z86E3016PEG - 8-Bit 16MHz 4KB OTP MCU | Zilog
Z86E3016PEG

Z86E3016PEG - 8-Bit 16MHz 4KB OTP MCU | Zilog

The Zilog Z86E3016PEG is an 8-bit Z8 microcontroller operating at 16 MHz with 4 KB of one-time-programmable memory in a 28-pin plastic dual-inline package. The verified product listings identify the device as the Z8 family member Z86E3016PEG and describe it as an 8-bit, 16 MHz microcontroller with 4K × 8 OTP program memory and UART capability. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals into one device. The Z8 belongs to the 8-bit microcontroller hierarchy, where each CPU cycle operates on an 8-bit data word. Such devices are used to read inputs, execute embedded control logic, and operate outputs in products where a compact controller, deterministic behavior, and modest processing requirements are more important than high computational throughput. The Z86E3016PEG's principal verified characteristics are its 16 MHz operating frequency, 8-bit CPU architecture, 4 KB OTP memory, and 28-pin PDIP package. The Mouser listing characterizes the device as an 8-bit MCU with 8K OTP and UART support, while the DigiKey listing identifies 4 KB, expressed as 4K × 8. Because these distributor descriptions express the OTP organization differently, engineers should confirm the exact program-memory organization against the manufacturer datasheet before assigning firmware capacity. The Z8 architecture is suitable for embedded motor-control, appliance-control, industrial-control, and serial-interface designs where an 8-bit CPU and UART simplify the control system. OTP program memory provides a one-time programmable implementation medium for products whose firmware is finalized before deployment. A 28-pin PDIP package also supports conventional through-hole assembly, prototyping, and manual inspection rather than requiring a fine-pitch surface-mount process. Before finalizing a design, verify the device's exact pin assignments, electrical limits, oscillator options, I/O count, UART characteristics, current consumption, and timing requirements using the manufacturer datasheet. Those parameters are not fully present in the supplied distributor snippets and are therefore marked as needed rather than estimated. Confirm that the 16 MHz clock source and UART baud-rate requirements can be met by the selected oscillator and external support components. This page combines verified distributor specifications, package information, pricing evidence, and explicitly qualified replacement analysis for the Z86E3016PEG. It also distinguishes verified drop-in candidates from unsupported cross-package options, helping engineers evaluate procurement and redesign decisions without treating package similarity as proof of functional equivalence.

RFQ संपर्क
Z86E3016PSG - 8-Bit 16MHz OTP MCU | Zilog
Z86E3016PSG

Z86E3016PSG - 8-Bit 16MHz OTP MCU | Zilog

Zilog Z86E3016PSG is an 8-bit Z8-family microcontroller with 16 MHz operating frequency, 4 KB of one-time-programmable program memory, 237 bytes of RAM, and 24 I/O pins in a 28-pin package. It is designed for cost-sensitive embedded-control applications that require simple programming, low-power wake-up behavior, and dedicated on-chip peripherals. A microcontroller is a programmable semiconductor that integrates a CPU, memory, I/O ports, timers, and support circuitry on one chip. The Z8 architecture belongs to the broader microcontroller and embedded-processor hierarchy. Compared with application-specific controllers, an OTP microcontroller offers a straightforward way to implement fixed control logic in appliances, security devices, HVAC equipment, and other compact electronic products. Verified device features include one-time-programmable memory, enhanced wake-up circuitry, programmable watchdog timers, and selectable low-noise EMI options. The 16 MHz operating speed provides processing headroom for simple digital control, while 24 I/O lines allow the device to connect to sensors, switches, indicators, and actuators. Two 8-bit timers support periodic events, timing delays, and basic event generation without requiring additional timing components. The 4 KB OTP program memory is organized as 4K by 8 bits, and the device includes 237 bytes of RAM for working data. OTP memory permits the final application firmware to be programmed once, making the controller well suited to production products whose control logic does not require field updates. This simplifies manufacturing compared with flash-programmable alternatives, but it also means a firmware revision generally requires a new programmed device rather than an in-system memory update. Typical uses include appliance controls, security-system peripherals, temperature and process-control equipment, HVAC modules, and compact industrial controllers. The 24 available I/O pins simplify designs that need multiple digital inputs and outputs, while the watchdog timer helps recover operation after faults or unexpected program flow. Enhanced wake-up circuitry supports low-power systems that must respond to external activity without maintaining continuous high activity. Designers should verify the exact package pinout, operating voltage, clock configuration, and programming procedure against the Zilog datasheet before layout. The provided search data confirms a 28-pin device but does not expose authoritative pin names or a complete manufacturer PDF URL, so those details remain marked as data needed rather than being inferred. Firmware and board design should also account for OTP programming limitations and the watchdog timeout behavior.

RFQ संपर्क
Z86E3016SSG - 8-Bit 16MHz OTP Microcontroller | Zilog
Z86E3016SSG

Z86E3016SSG - 8-Bit 16MHz OTP Microcontroller | Zilog

The Zilog Z86E3016SSG is an 8-bit Z8 microcontroller operating at 16 MHz with 4 KB of one-time-programmable program memory, 125 bytes of RAM, and 24 I/O lines in a 28-pin SOIC package. It operates from a 4.5 V to 5.5 V supply and is specified for a 0°C to 70°C ambient-temperature range. A microcontroller is an integrated circuit that combines a processor core, nonvolatile program memory, working RAM, and peripherals on one semiconductor device. The Z86E3016SSG belongs to the Z8 family of 8-bit microcontrollers and provides a compact control platform for products that require deterministic digital control but do not need the processing power, memory, or peripheral complexity of a 32-bit embedded processor. Its one-time-programmable architecture is intended for production devices whose firmware does not need field reprogramming. The principal device characteristics include a 16 MHz clock, 4 KB OTP program memory organized as 4K by 8 bits, 125 bytes of RAM, and 24 general-purpose I/O lines. Integrated power-on reset and watchdog-timer functions support dependable startup and recovery behavior. The 28-pin surface-mount SOIC package supports conventional PCB assembly while providing enough I/O capacity for sensors, indicators, control inputs, and external logic. The Z8 processor architecture provides an 8-bit execution model optimized for control-oriented embedded systems. At 16 MHz, it offers substantially greater timing headroom than many simpler 8-bit controllers, while the compact instruction and memory architecture keeps firmware and peripheral integration straightforward. Programmable OTP options include an RC oscillator and EPROM protection, allowing the selected configuration to be fixed according to the product's operating requirements. Typical uses include appliance controllers, industrial control modules, security and access-control equipment, instrumentation peripherals, and small embedded control subsystems. In each case, the 24 available I/O lines and 125 bytes of RAM are important constraints. Designers should allocate RAM carefully for stacks, buffers, and intermediate state, while treating the 4 KB OTP capacity as the final firmware limit. The primary design consideration is that one-time-programmable memory cannot be changed after programming. Firmware validation, programming fixtures, and production traceability therefore must be completed before devices reach end users. PCB layouts should also follow the verified 28-SOIC footprint and provide the decoupling and clock circuitry required by the manufacturer datasheet. This page consolidates verified distributor specifications, sourcing links, family alternatives, and practical selection guidance. It also distinguishes documented device facts from pricing, lifecycle, and pin-level information that was not established by the supplied source data.

RFQ संपर्क
Z86E3116PEG - 8-Bit 16MHz 2KB OTP MCU | Zilog
Z86E3116PEG

Z86E3116PEG - 8-Bit 16MHz 2KB OTP MCU | Zilog

The Zilog Z86E3116PEG is an 8-bit Z8 microcontroller with 2KB (2K x 8) of one-time programmable program memory, 125 bytes of RAM, 24 I/O lines, and a maximum operating frequency of 16MHz in a 28-DIP (0.600-inch, 15.24mm) package. Its specified operating-voltage range is 4.5V to 5.5V. An 8-bit microcontroller is a compact embedded-control IC used to execute firmware, read inputs, and control outputs in dedicated electronic systems. The Z86E3116PEG belongs to the microcontroller hierarchy, combining a Z8 processor core, program memory, RAM, digital I/O, and embedded timing functions. Its one-time-programmable architecture is intended for products where firmware is written during manufacturing and does not need to be updated in the field. Key device characteristics include 16MHz operation, 24 general-purpose I/O lines, 125 bytes of RAM, and programmable OTP options identified in the source data as RC oscillator, EPROM protection, auto latch disable, and permanent settings. Integrated features reported by the Microchip USA product listing include a power-on reset and watchdog timer, providing basic startup supervision and recovery support for embedded control firmware. The device uses a 5V-class supply range of 4.5V to 5.5V. Its 28-DIP package provides through-hole mounting and a 0.600-inch body width, making it appropriate for legacy-style control boards, industrial controllers, appliance controllers, and compact embedded systems assembled with conventional through-hole techniques. Because the available product information does not include the complete datasheet pin map, individual signal assignments cannot be reproduced safely here. Typical application roles include simple sequencing and logic control, switch and relay management, status-indicator control, small industrial equipment interfaces, and dedicated appliance controllers. In each case, firmware stored in the 2KB OTP program memory determines the control behavior, while the 24 I/O lines provide connections to external sensors, switches, and actuators. Designers should account for the 4.5V to 5.5V supply requirement, confirm that the board uses the 28-pin DIP footprint, and validate timing, oscillator, reset, and watchdog behavior against the manufacturer datasheet before production release. The available data identifies the oscillator as internal, but its frequency range and detailed configuration requirements are not stated. This page consolidates verified distributor specifications, current sourcing information, package details, application guidance, and explicit data gaps. It also distinguishes verified facts from unspecified parameters, helping engineers evaluate the Z86E3116PEG without mistaking generic cross-reference tools for evidence of a pin-compatible replacement.

RFQ संपर्क
Z86E3116SEG - 8-Bit 16MHz 2KB OTP MCU | Zilog
Z86E3116SEG

Z86E3116SEG - 8-Bit 16MHz 2KB OTP MCU | Zilog

The Zilog Z86E3116SEG is an 8-bit Z8 CISC microcontroller with 2KB of one-time-programmable program memory, 125 bytes of RAM, 24 I/O lines, and a 16MHz maximum operating frequency, supplied in a 28-pin SOIC package. It operates from a 4.5V to 5.5V supply across a -40°C to +105°C temperature range. A microcontroller is a programmable semiconductor that integrates a CPU, memory, digital I/O, and supporting peripherals into one package. The Z86E3116SEG belongs to the Z8 family of 8-bit microcontrollers, a class commonly used for embedded control because it combines a compact instruction set, dedicated I/O, and low-cost single-power-supply operation. Its larger program and data memories distinguish it from basic 8-pin devices while retaining the straightforward architecture suited to appliance controls, interface logic, and compact embedded systems. Key features include 2KB of OTP program memory, 125 bytes of RAM, 24 I/O lines, and operation up to 16MHz. Programmable OTP options listed in the device data include an RC oscillator, EPROM protection, auto latch disable, and permanent disable. The 28-pin SOIC package is also available in tube packaging according to the verified distributor data, supporting conventional through-hole board assembly rather than a compact surface-mount land pattern. The device uses the Z8 CISC architecture and includes an internal oscillator option according to the published specification summary. Its 125-byte RAM supports protocol state, counters, status flags, and short working buffers, while the 2KB OTP program area provides fixed firmware storage after programming. Because OTP memory cannot be electrically rewritten, firmware changes normally require a new programmed device rather than an in-circuit update. Typical uses include temperature controllers, appliance user interfaces, simple motor-control logic, industrial panel controllers, and embedded peripheral interfaces. In these applications, the 24 available I/O lines can distribute digital signals while the 16MHz operating rate supports time-based control routines and serial communication handling. A designer should still budget memory for interrupts, protocol handling, and application logic. The primary design constraint is nonvolatile program flexibility: OTP programming makes Z86E3116SEG appropriate for production builds with stable firmware, while applications requiring field updates may prefer a flash-memory MCU. Board layouts must also respect the 28-pin SOIC footprint and provide the required 4.5V to 5.5V supply, decoupling, programming interface, and exposed I/O routing. This product page consolidates verified distributor specifications, package information, temperature limits, and drop-in comparison data, then adds practical guidance on OTP programming, power-supply design, PCB layout, and selection constraints that are not presented as a complete replacement for the manufacturer datasheet.

RFQ संपर्क
Z86E3412SSG - 12MHz 16KB OTP 8-Bit MCU | Zilog
Z86E3412SSG

Z86E3412SSG - 12MHz 16KB OTP 8-Bit MCU | Zilog

The Zilog Z86E3412SSG is an 8-bit Z8 Z8 One-Time Programmable microcontroller with a 12 MHz clock, 16 KB of OTP program memory organized as 16K x 8, and a 28-pin SOIC package. It is designed for embedded control applications that require a compact 8-bit controller, nonvolatile program storage, and a peripheral-oriented MCU architecture. An 8-bit microcontroller is a microprocessor and embedded-control IC built around an 8-bit processing architecture. The Z8 family belongs to the broader hierarchy of embedded processors, microcontrollers, and semiconductors. One-time programmable memory allows firmware to be written once during manufacturing or programming, providing nonvolatile program storage without the removable-program-memory cost of EEPROM. This makes the Z86E3412SSG suitable for fixed-function products whose firmware does not need field updates. The principal device characteristics include a 12 MHz operating frequency, 16 KB of OTP program memory, 8-bit processing, CMOS construction, and a 28-pin SOIC package. The reported operating-temperature range for this exact ordering code is 0°C to +70°C. The part is also identified as Pb-free, although separate RoHS, REACH, and halogen-free declarations were not included in the supplied source data and therefore remain unconfirmed. The 12 MHz clock rate provides the timing headroom expected from a Z8-class embedded controller, while the 16K x 8 OTP organization determines the available program address space. Because the source data does not provide RAM capacity, I/O pin assignments, peripheral inventories, electrical limits, watchdog behavior, or timing characteristics, those details must be confirmed in the manufacturer datasheet before a board design is released. Typical uses include fixed-function industrial controllers, appliance-control panels, small instrument controllers, status interfaces, and embedded control modules where an 8-bit processor and OTP firmware storage are sufficient. Its 28-pin SOIC package also supports conventional surface-mount assembly, but package dimensions, pin geometry, and exposed thermal requirements are not included in the supplied evidence. For new layouts, engineers should verify the complete 28-pin pinout, required decoupling, oscillator connection, programming method, reset requirements, and absolute maximum ratings against the official datasheet. The OTP programming process should also be coordinated with manufacturing because an incorrectly programmed device generally cannot be rewritten like flash memory. This page consolidates the verified distributor listings, an identified same-package family alternative, package constraints, pricing evidence, and engineering-selection guidance. It also clearly separates confirmed Z86E3412SSG facts from electrical and programming details that require manufacturer documentation.

RFQ संपर्क
Z86E4016FEC - 8-Bit 16MHz 4KB OTP MCU | Zilog | LQFP-44
Z86E4016FEC

Z86E4016FEC - 8-Bit 16MHz 4KB OTP MCU | Zilog | LQFP-44

Zilog, Inc. Z86E4016FEC is an 8-bit Z8 microcontroller with a 16 MHz maximum operating frequency, 4 KB of one-time-programmable program memory, and a 44-LQFP surface-mount package measuring 10 mm by 10 mm. It integrates 32 general-purpose I/O pins, power-on reset, and a watchdog timer for compact embedded-control designs. An 8-bit microcontroller is a programmable integrated circuit designed around an eight-bit processor and a set of dedicated peripherals. Within the embedded-control hierarchy, the Z86E4016FEC belongs to the Z8 family of Zilog microcontrollers and provides a combination of processor throughput, OTP program storage, digital I/O, reset supervision, and watchdog protection in one device. The principal features include 8-bit processing at up to 16 MHz, 4 KB of OTP program memory, and 32 general-purpose I/O pins. Two 8-bit timers are also identified in the verified technical listing. OTP memory provides a permanent on-chip program store, which can be appropriate for cost-sensitive products in which firmware does not require field updates. The device uses the Z8 architecture and is intended for embedded products requiring straightforward digital control rather than high-bandwidth processing. Its 16 MHz operating speed supports control loops, button and sensor handling, indicator updates, and peripheral coordination. The integrated power-on reset and watchdog timer help establish reliable startup behavior and recover from certain software faults. Typical application areas include industrial control panels, appliance controllers, building equipment, simple motor-control interfaces, and dedicated embedded modules. The 44-LQFP package provides 32 general-purpose I/O pins, allowing a design to connect multiple sensors, switches, displays, and actuators while leaving fewer functions to external logic. Design planning should focus on OTP programming timing, available RAM, pin multiplexing, oscillator configuration, and programming-tool compatibility. Because the verified data does not provide a complete pin list, voltage limits, or thermal ratings, those details must be confirmed against the official Zilog documentation before schematic capture or PCB release. This product page consolidates verified distributor specifications, package information, application guidance, and verified sourcing links. It also clearly separates confirmed data from unavailable specifications, helping engineers make sourcing and design decisions without treating unverified electrical details as guaranteed facts.

RFQ संपर्क
Z86E4016FEG - 8-Bit 16MHz OTP Microcontroller | Zilog
Z86E4016FEG

Z86E4016FEG - 8-Bit 16MHz OTP Microcontroller | Zilog

The Zilog Z86E4016FEG is an 8-bit Z8 microcontroller with 4 KB of one-time-programmable program memory, 236 x 8 bits of RAM, 32 I/O pins, and a maximum operating speed of 16 MHz. It is housed in a 44-LQFP surface-mount package measuring 10 x 10 mm. The device also includes an internal oscillator, Power-On Reset (POR), and a Watchdog Timer (WDT), providing the core resources for compact embedded control designs. An 8-bit microcontroller is a microprocessor integrated with memory, I/O, and supporting peripherals on one integrated circuit. Within the semiconductor hierarchy, the Z86E4016FEG is an MCU, a microcontroller, and an embedded processing IC designed for control-oriented tasks rather than high-throughput computation. Its OTP program memory allows firmware to be programmed once during manufacturing or final assembly, while its 236-byte RAM supports working variables, stack operations, and short-lived application data. The principal feature set includes 4 KB of OTP program memory, 236 x 8 bits of RAM, 32 general-purpose I/O pins, and a 16 MHz operating speed. An internal oscillator reduces the need for an external clock source in applications that do not require an extremely precise timing reference. The Power-On Reset establishes a known startup state, while the Watchdog Timer helps recover the controller from an unintended stalled execution sequence. The Z86E4016FEG belongs to the Zilog Z8 family, an 8-bit MCU architecture commonly used for appliance control, simple industrial interfaces, embedded instrumentation, and compact control panels. Its 32 I/O pins provide substantial external connectivity relative to smaller 8- and 16-pin devices, making the device useful for keypads, displays, sensors, relay logic, and communication peripherals when their electrical requirements are compatible with the MCU's specifications. The 44-LQFP package supports surface-mount assembly but requires careful land-pattern design and adequate pin escape routing. Published source material states that total package power dissipation should not exceed 1.2 W under the indicated stress conditions. Designers should therefore verify the complete operating-voltage, input-pin, clock, and output-drive budget against the manufacturer datasheet before releasing a production PCB. This product page consolidates the verified Z86E4016FEG specifications, package details, source links, engineering guidance, and replacement analysis. It also clearly separates verified facts from unavailable electrical details, helping engineers avoid assumptions about voltage limits, timer channels, communications peripherals, or pin-level functions that are not present in the supplied source data.

RFQ संपर्क
Z86E4412PSG - 8-Bit 12MHz 16KB OTP MCU | Zilog
Z86E4412PSG

Z86E4412PSG - 8-Bit 12MHz 16KB OTP MCU | Zilog

Zilog Z86E4412PSG is an 8-bit Z8 embedded microcontroller with a 12MHz core, 16KB of one-time-programmable program memory, and 236 bytes of RAM in a 40-pin PDIP package. The device integrates Power-On Reset, a Watchdog Timer, and EBI/EMI connectivity, making it suitable for cost-sensitive embedded control systems that require deterministic peripheral access and compact code storage. A microcontroller is a programmable integrated circuit that combines a processor core, memory, and peripherals on one semiconductor die. The Z8 MCU family belongs to the broader embedded-controller hierarchy, where an 8-bit MCU provides efficient control for sensors, actuators, human-interface circuits, and industrial equipment. Unlike field-programmable Flash memory, the Z86E4412PSG uses OTP memory, so its application program is permanently committed during device programming. Key features include a 12MHz operating frequency, 16K × 8 organization for the 16KB OTP program memory, and 236 × 8 bytes of RAM. The integrated Power-On Reset helps establish a known initial controller state, while the Watchdog Timer provides a mechanism for recovering from stalled software execution. EBI/EMI expands the available external interface resources for communicating with additional memory or peripheral devices. The Z86E4412PSG uses an 8-bit architecture optimized for embedded control rather than high-throughput computation. Its 12MHz clock provides the execution rate for supervisory loops, status monitoring, and basic user-interface tasks. The 236-byte RAM supports working variables and stack operations, although complex buffering or protocol stacks may require an external memory device connected through the external bus interface. Typical uses include industrial control panels, building equipment, security and access peripherals, appliance controllers, motor-control interfaces, and compact embedded sensing systems. The 40-pin PDIP package is particularly useful for prototypes, through-hole industrial assemblies, and designs where a socketed controller simplifies replacement or inspection. The primary design consideration is OTP programming. Engineers should validate the complete firmware and all configuration bytes before programming because OTP memory cannot be rewritten, and they should verify external-bus timing and peripheral assignments against the manufacturer datasheet. Supply voltage, pin-specific limits, oscillator requirements, and programming procedures are not available in the supplied source excerpts and must be confirmed from the manufacturer datasheet. This page consolidates verified distributor and manufacturer-related source information, compares the available documented substitute, and identifies missing electrical data explicitly. It is intended to support engineering selection while preventing unverified voltage, pinout, pricing, and lifecycle assumptions from being presented as facts.

RFQ संपर्क
Z86E6116FSC - 16MHz 8-Bit OTP Microcontroller | Zilog
Z86E6116FSC

Z86E6116FSC - 16MHz 8-Bit OTP Microcontroller | Zilog

The Zilog Z86E6116FSC is an 8-bit Z8 microcontroller operating at 16 MHz, with 16 KB of one-time-programmable program memory, 236 bytes of RAM, UART capability, and a 44-pin LQFP package measuring 10 mm by 10 mm. Its OTP program memory makes the device suitable for compact production designs in which the finished controller code must not be reprogrammed. An 8-bit microcontroller is a programmable semiconductor that integrates a CPU, memory, and peripherals on one chip. Within the product hierarchy, this device belongs to the Z8 family of 8-bit microcontrollers and belongs broadly to the integrated-circuit and embedded-controller categories. Z8 devices combine a compact processor architecture with dedicated I/O and serial-interface resources for cost-sensitive embedded control. The verified device data identifies a 16 MHz operating clock, 16 KB of OTP program memory organized as 16K by 8 bits, and 236 bytes of general-purpose RAM. The listing also identifies a UART interface, making the MCU suitable for designs that need a simple serial communications channel. Its 44-LQFP package provides a higher pin count than a basic 8-bit controller and supports more external connections in a surface-mount production PCB. The Z8 architecture is designed for embedded-control workloads where modest processing throughput is sufficient. Program storage is one-time-programmable rather than mask-programmable or electrically reprogrammable, which can simplify production control by preventing accidental changes after programming. The 16 MHz operating rate supports time-based control, input scanning, state-machine logic, and communication routines without requiring a higher-bit-class processor. Typical uses include appliance controllers, small industrial automation modules, instrument panels, communication interfaces, and embedded peripheral controllers. The UART is particularly relevant where an external host computer, display, sensor interface, or service connector uses a serial link. Engineers should confirm the exact peripheral pin multiplexing, electrical limits, timing characteristics, and programming procedure against the manufacturer datasheet before finalizing a PCB or firmware. One important design consideration is that OTP memory cannot be revised after programming. Firmware validation, programming-file control, and assembly-line traceability therefore need to be planned before deployment. Supply voltage, clock tolerances, I/O limits, reset behavior, and absolute maximum ratings are not present in the supplied excerpts and must be verified in the complete manufacturer datasheet. This product page consolidates the verified distributor specifications, package information, sourcing links, family relationships, and engineering cautions for Z86E6116FSC. It also distinguishes confirmed technical facts from unavailable details and avoids presenting unverified pricing, pin assignments, or drop-in replacements as authoritative.

RFQ संपर्क
Z86E6316VSG - 8-Bit 16MHz 32KB OTP MCU | Zilog
Z86E6316VSG

Z86E6316VSG - 8-Bit 16MHz 32KB OTP MCU | Zilog

The Zilog Z86E6316VSG is an 8-bit Z8 Z8 microcontroller with a 16 MHz clock, 32 KB of one-time-programmable program memory, 236 bytes of data RAM, and an operating supply range of 4.5 V to 5.5 V. The device is supplied in a 44-LCC J-lead plastic leaded-chip carrier package, identified by the VSG suffix. A microcontroller is a programmable system-on-chip that integrates a CPU, nonvolatile program memory, data memory, and peripherals into one component. The Z86E6316VSG belongs to the Z8 family of 8-bit microcontrollers, a category used for cost-sensitive embedded control, monitoring, keypad, appliance, and industrial-control designs. Its OTP program memory allows the final firmware to be written once after programming and is not electrically rewriteable. The principal device characteristics are a 16 MHz operating frequency, 32 KB of OTP program memory, 236 bytes of RAM, a 4.5 V to 5.5 V supply range, and integrated UART capability. The 236-byte RAM figure distinguishes internal data memory from the 32 KB program area and should be considered when sizing buffers, communication queues, and application state. The listed 44-LCC package also provides more external connection options than the small leaded-chip carriers commonly used for basic 8-bit control. The Z8 architecture is designed around an 8-bit CPU and embedded peripherals rather than a high-level application processor. That architecture is appropriate when firmware must handle timers, serial communication, discrete inputs, and output control within deterministic response requirements. Because program memory is OTP rather than mask-programmed ROM, the device can support application-specific firmware while retaining a single finished component configuration. Typical uses include serial-connected controllers, industrial modules, instrumentation interfaces, appliance control boards, and embedded system nodes. The UART is particularly useful for connecting the MCU to a host controller, sensor interface, display controller, or service port. For designs needing more general-purpose serial connectivity, the Zilog MCU can work alongside a dedicated interface device such as the MAX232DR or MAX202IDR. A critical design consideration is that OTP memory cannot be updated after programming. Firmware validation, programming fixtures, and board bring-up procedures should therefore be completed before large-volume deployment. Decoupling, oscillator stability, reset behavior, and exposed-pin assignments must also be checked against the manufacturer datasheet because a PLCC replacement is not automatically a functional replacement. This page consolidates verified distributor specifications, package and memory details, pricing references, candidate drop-in alternatives, and practical replacement guidance that are not presented together on a single distributor listing. It also distinguishes documented facts from fields that still require confirmation from the Zilog datasheet.

RFQ संपर्क
Z86E7316FSC - 8-Bit 16MHz OTP Microcontroller | Zilog
Z86E7316FSC

Z86E7316FSC - 8-Bit 16MHz OTP Microcontroller | Zilog

Zilog Z86E7316FSC is an 8-bit Z8 ZIRC microcontroller operating at 16 MHz, with 32 KB of one-time-programmable memory, supplied in a 44-pin LQFP package measuring 10 mm by 10 mm. The device is positioned for embedded control applications requiring a compact, surface-mount MCU with integrated program storage. A microcontroller is a semiconductor device that combines a processor core, program memory, data memory, input/output ports, and embedded peripherals on one integrated circuit. Within the broader hierarchy, the Z86E7316FSC is an 8-bit microcontroller based on the Z86E7X architecture. Its Z8 core uses an expanded register file for register-mapped peripherals, general-purpose I/O circuitry, and counter and timer resources, making the device suitable for control-oriented products. The verified product listing identifies 32 KB of OTP program memory and a maximum clock frequency of 16 MHz. OTP memory is programmed once during manufacturing or system preparation and is commonly selected for cost-sensitive products where firmware is finalized before deployment. The 44-LQFP package provides 44 external leads for power, ground, I/O, and control-signal connections while supporting compact, automated PCB assembly. The Z86E7X architecture is based on Zilog's 8-bit microcontroller core and expanded register file. This organization provides direct access to I/O circuitry and timer functions without requiring a separate external interface circuit for many embedded-control tasks. Detailed electrical limits, timer counts, RAM capacity, operating-temperature endpoints, and individual peripheral configurations were not included in the supplied verified records and should therefore be confirmed in the manufacturer datasheet before design release. Typical uses include appliance and consumer-product control, computer peripheral interfaces, automotive electronics, and compact embedded-control modules. The 16 MHz operating speed provides a higher-performance clock than many simple 8-bit control devices, while 32 KB of OTP program storage allows a comparatively substantial firmware image to be held on-chip. The absence of communication interfaces in the supplied distributor records should not be interpreted as proof that the device has none; engineers must review the complete pin and peripheral tables. For a new design, begin with the exact 44-LQFP footprint and verify every pin function against the Z86E7X documentation before allocating board space. Keep programming and test access available if production programming is required, and validate timing behavior at the intended 16 MHz operating point. PCB layout should provide short, stable connections for clock and sensitive control signals, compliant decoupling close to the supply pins, and appropriate programming interface clearance. This product record consolidates the verified manufacturer-series and distributor information for Z86E7316FSC and distinguishes documented values from fields still requiring datasheet confirmation. It also provides focused application guidance, design checks, and sourcing links to help engineers evaluate the 8-bit 16 MHz OTP microcontroller without inferring unsupported specifications.

RFQ संपर्क