माइक्रोकंट्रोलर्स

उत्पाद (20,000+)

ATSAMG51N18A-AU - 48MHz ARM Cortex-M4 MCU 256KB Flash | Microchip
ATSAMG51N18A-AU

ATSAMG51N18A-AU - 48MHz ARM Cortex-M4 MCU 256KB Flash | Microchip

The Microchip ATSAMG51N18A-AU is a 32-bit ARM Cortex-M4 microcontroller with FPU from the SAM G51 family, operating at up to 48MHz with 256KB Flash and 64KB SRAM, housed in a 100-pin LQFP (14x14 mm) package. It combines low-power features with DSP and floating-point capability for embedded designs that demand efficient numeric processing in a cost-effective form factor. A microcontroller (MCU) is an integrated circuit that combines a CPU core, memory, and programmable peripherals on a single silicon die. The Cortex-M4 core belongs to ARM's Cortex-M family, which sits hierarchically under ARM Cortex processors -> 32-bit RISC processors -> embedded CPUs. SAM G51 devices use the Cortex-M4 with single-precision FPU and DSP extensions, enabling signal-processing workloads that simpler M0+ or M3 cores cannot efficiently execute. This hierarchy matters when selecting among thousands of MCUs: Cortex-M4 is the right choice when fixed-point or floating-point math throughput is required without moving to Cortex-M7 complexity. Key features of the ATSAMG51N18A-AU include 256KB embedded Flash, 64KB SRAM, an FPU and DSP instruction set, a high-speed 48MHz operation, multiple serial interfaces including I2C, SPI, UART and I2S, and configurable PWM timers. The device integrates a 12-bit ADC, 10-bit DAC, and on-chip voltage regulator, allowing single-supply operation from 1.62V to 3.6V. The LQFP-100 footprint provides generous I/O for parallel buses, multiple serial channels, and motor-control PWM outputs. The SAM G51 series was designed to minimize active-mode current and accelerate sleep-mode entry, reducing overall energy budget in duty-cycled applications. Its architecture supports zero-wait-state Flash execution at 48MHz and a low-power RTC domain that retains state during deep-sleep. Compared to legacy Cortex-M3 designs, the M4 with FPU executes filter and control algorithms in fewer cycles, which reduces both MIPS load and average power in DSP-driven workloads. Typical applications include consumer audio devices, IoT sensor hubs, industrial control panels, motor control, and low-cost graphical user interfaces. Engineers also deploy it in smart-metering, building automation, and wireless sensor node controllers where DSP assists modulation/demodulation. The wide LQFP-100 footprint supports evaluation on breadboards and hand-solderable prototypes, making it popular in education and small-batch products. When designing with this part, place decoupling capacitors (100nF plus 4.7uF bulk) within 5mm of each power pin, follow Microchip's SAM G51 hardware design checklist for crystal layout, and ensure the SWD pins (PA30, PA31) are accessible for in-system programming. Use Atmel Studio 7 or MPLAB X IDE with the device pack installed for firmware development.

RFQ संपर्क
ATSAMG53G19A-UUT - SAM G53 Cortex-M4 MCU 512KB Flash | Microchip
ATSAMG53G19A-UUT

ATSAMG53G19A-UUT - SAM G53 Cortex-M4 MCU 512KB Flash | Microchip

The Microchip ATSAMG53G19A-UUT is a low-power ARM Cortex-M4 microcontroller with FPU, integrating 512 KB of Flash and 96 KB of SRAM in a compact 49-ball WLCSP package. Designed for industrial temperature ranges (-40C to +85C), the device targets energy-constrained connected sensor nodes, wearable electronics, and human-machine interface applications that benefit from a small board footprint. An ARM Cortex-M4 microcontroller is a 32-bit RISC processor core licensed by Arm Holdings that combines high-performance digital signal processing with a single-precision floating-point unit. Microcontrollers in this class sit within the broader taxonomy of embedded microcontrollers -> RISC microcontrollers -> ARM Cortex-M family -> Cortex-M4 subfamily, and are commonly selected for IoT endpoints, motor control, and low-power wireless designs. The Cortex-M4 architecture brings Thumb-2 instruction efficiency, hardware single-cycle MAC, and optional FPU, all of which reduce active-mode current and accelerate return-to-sleep transitions. Key features of the ATSAMG53G19A-UUT include a 48 MHz maximum CPU clock, full Cortex-M4 DSP instruction set with single-precision FPU, a 12-bit ADC, multiple SERCOM interfaces configurable as USART/UART/SPI/I2C, and a high-speed USB 2.0 Full-Speed device port. The device integrates Microchip's proprietary SleepWalking peripherals that wake the CPU only on relevant events, enabling deep-sleep current in the single-digit microamp range for battery-powered designs. Technically, the SAM G53 series implements a tightly-coupled SRAM subsystem with zero-wait-state access at full CPU speed, and an efficient Flash controller supporting offline programming. The integrated voltage regulator allows single-supply operation from 1.62V to 3.6V, simplifying power-tree design and supporting direct Li-ion or 2x AA battery sources. Typical applications include Bluetooth Low Energy sensor hubs (paired via SPI to a companion radio), low-power wearables with always-on sensors, USB human-interface devices such as mice and keyboards, and industrial control boards requiring DSP-class math at modest cost. The 49-ball WLCSP package makes it ideal where PCB area is at a premium. When designing with this MCU, allocate sufficient decoupling (one 100 nF X7R per VDD pin group plus a bulk 4.7 uF) and follow Microchip's WLCSP routing guidelines to keep the high-speed USB 90-ohm differential pair matched. Erase and program Flash via SWD or the pre-programmed bootloader to avoid expensive parallel programming fixtures. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers and procurement teams evaluate the ATSAMG53G19A-UUT for low-power, footprint-sensitive designs as of 2026-09-22.

RFQ संपर्क
ATSAMG53G19B-UUT - 48MHz Cortex-M4 MCU 512KB Flash | Microchip
ATSAMG53G19B-UUT

ATSAMG53G19B-UUT - 48MHz Cortex-M4 MCU 512KB Flash | Microchip

The Microchip Technology (formerly Atmel) ATSAMG53G19B-UUT is a 32-bit ARM Cortex-M4 RISC microcontroller running up to 48 MHz, integrating 512 KB of Flash and 96 KB of SRAM in a compact 49-ball WLCSP (2.84 x 2.84 mm) package with industrial temperature rating. This SMART SAM G53 series device targets space-constrained, performance-oriented embedded designs that need DSP-style arithmetic and a rich peripheral mix on a single die. A 32-bit microcontroller (MCU) is a single-chip processor that integrates a CPU core, program memory (Flash), working memory (SRAM), and a programmable set of peripherals (timers, communication interfaces, ADC, I/O) into one package. In the wider semiconductor taxonomy, MCUs sit between 8/16-bit microcontrollers and full microprocessors (MPUs); the ARM Cortex-M4 sub-family specifically adds a single-precision FPU and DSP extensions (MAC, saturating arithmetic), placing it above Cortex-M0/M0+ and below Cortex-M7 in compute density. The SAM G53 family was introduced by Atmel (now Microchip) as a low-power, mixed-signal Cortex-M4 line aimed at human-machine interface (HMI), audio, motor drive, and IoT edge nodes. Key features of the ATSAMG53G19B-UUT include: 512 KB embedded Flash, 96 KB SRAM, Cortex-M4 core with FPU and DSP instructions, Fmax = 48 MHz, one USART plus two UARTs, three I2C (TWI) interfaces, two SPI peripherals (one of which is configurable as an I2S for audio), a 12-bit ADC, a 12-bit DAC, PWM timers, and a full-speed USB 2.0 device/host with on-chip PHY. The 49-ball WLCSP gives the lowest profile in the family, enabling ultra-thin wearables, hearables, and sensor modules. The on-chip FPU and DSP extensions accelerate audio codecs, sensor fusion, and small closed-loop control loops without offloading to a companion DSP. The integrated USB 2.0 Full-Speed PHY removes the need for an external transceiver, and the dual I2S-capable SPIs allow direct connection to digital MEMS microphones and audio DACs. Compared with the larger LQFP/QFN SAM G53 variants, the WLCSP version sacrifices some pin access for footprint, so engineers must route high-speed signals on inner PCB layers. Typical applications include wearable fitness bands, Bluetooth/wireless audio headsets (paired with an external radio SoC), USB HID peripherals such as keyboards and game controllers, low-cost HMI panels with capacitive touch, sensor hubs for IoT, and battery-powered industrial data loggers. The 96 KB SRAM is comfortable for small RTOS use (FreeRTOS, Micrium) and DSP buffers. When designing with this part, note that the 49-ball WLCSP requires PCB-level assembly expertise (NSMD pads, micro-via-in-pad recommended) and that the 48 MHz ceiling limits some heavy DSP workloads; for higher throughput, consider the SAM E70 or SAM S70 Cortex-M4F families. Always validate the full peripheral pinout against your specific WLCSP ball map before committing to layout, because the BGA-style package is not breadboard-friendly. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for selection, sourcing, and layout planning of the ATSAMG53G19B-UUT.

RFQ संपर्क
ATSAMG53N19A-AU - ARM Cortex-M4 48MHz MCU | Microchip
ATSAMG53N19A-AU

ATSAMG53N19A-AU - ARM Cortex-M4 48MHz MCU | Microchip

The Microchip Technology ATSAMG53N19A-AU is an ARM Cortex-M4 microcontroller with floating-point unit (FPU), operating at up to 48 MHz core clock, integrating 512 KB of Flash and 96 KB of SRAM, and housed in a 100-pin LQFP (14x14 mm) industrial-temperature package. The device is a member of the SAM G53 family of low-power Cortex-M4 microcontrollers aimed at embedded applications requiring deterministic real-time performance and efficient DSP handling. A microcontroller (MCU) is a system-on-chip that integrates a CPU core, program memory (typically Flash), data memory (SRAM), and a rich set of peripherals into a single package. The ARM Cortex-M4 architecture adds a single-precision IEEE-754 floating-point unit and DSP extensions to the Cortex-M3 baseline, while maintaining deterministic interrupt latency (typically 12 cycles) and Thumb-2 instruction-set efficiency. Within the broader product taxonomy, the ATSAMG53N19A-AU belongs to the 32-bit MCU category, which itself is a subfamily of microcontrollers and a major branch of embedded processors alongside 8-bit MCUs (PIC, AVR) and DSPs. Key features of this part include the 48 MHz Cortex-M4 core, hardware FPU, 512 KB on-chip Flash, 96 KB SRAM, an integrated 12-bit ADC, multiple USART/UART/SPI/TWI peripherals, USB 2.0 Full-Speed device with on-chip transceiver, up to 38 GPIO lines, and a 1.5 to 3.6 V supply range. An on-chip ultra-low-power RTC, multiple sleep modes, and a 32.768 kHz crystal oscillator enable battery-friendly designs. The 100-LQFP package provides ample I/O for industrial control panels and human-machine interface (HMI) front-ends. Technically, the SAM G53 architecture pairs the Cortex-M4 core with a multi-layer AHB/APB bus matrix, a separate peripheral DMA controller (PDC), and a hardware cryptographic module on certain siblings. The 12-bit ADC achieves up to 1 MSPS sampling in single-ended mode, while the USB 2.0 Full-Speed peripheral and CAN controller provide connectivity options for industrial fieldbus and PC peripherals. The combination of low dynamic power consumption (under 1 mA/MHz at 1.8 V) and rapid wake-up from RTC alarm makes the part attractive for energy-constrained installations. Typical applications include industrial control panels, building automation (HVAC, lighting), USB peripherals such as data loggers, motor control boards (BLDC, stepper), wireless sensor node baseboards, point-of-sale (POS) terminals, and consumer HMI touch-front panels. The industrial -40 to +85 C operating range suits factory-floor and outdoor enclosures. When designing with this device, allocate the 48 MHz system clock carefully because the USB Full-Speed peripheral requires a 48 MHz ±0.25% reference, typically sourced from the 12 MHz main oscillator plus PLL. Power-supply decoupling must include at least a 1 uF bulk capacitor plus a 100 nF high-frequency bypass near each VDD/VDDIO pin pair, and the NRST line should include the recommended 100 nF capacitor to allow clean in-circuit resets. Plan Flash and SRAM budgets early because the 512 KB / 96 KB split is fixed and does not support external memory expansion on this LQFP-100 variant.

RFQ संपर्क
ATSAMG53N19B-AU - 512KB Flash Cortex-M4 MCU 48MHz | Microchip
ATSAMG53N19B-AU

ATSAMG53N19B-AU - 512KB Flash Cortex-M4 MCU 48MHz | Microchip

The Microchip ATSAMG53N19B-AU is a 32-bit ARM Cortex-M4 microcontroller with FPU from the SAM G53 family, featuring 512KB of Flash and 96KB of SRAM, clocked at up to 48MHz in a 100-pin LQFP (14x14 mm) industrial-temperature package. Operating from 1.62V to 3.6V, it integrates a Floating Point Unit, a 12-bit ADC, and the standard SAM G53 peripheral mix including USB FS, CAN, and multiple SERCOM/UART/SPI/I2C interfaces. An ARM Cortex-M4 microcontroller is a 32-bit RISC processor core designed by ARM for embedded applications, combining deterministic interrupt response with DSP extensions and an optional single-precision Floating Point Unit. In the broader product taxonomy, it sits below application processors and above 8/16-bit MCUs, occupying the mainstream performance tier for industrial IoT, motor control, and human-machine interface (HMI) designs. The Cortex-M4 core executes the Thumb-2 instruction set, allowing dense code with predictable cycle counts. Key features of the ATSAMG53N19B-AU include 512KB of in-system programmable Flash for application code, 96KB of SRAM for data and stack, 16KB of additional SRAM for backup retention, and an internal 12 MHz RC oscillator that can be re-calibrated against an external crystal for USB/SERCOM timing accuracy. The device exposes up to 38 GPIO pins organized across multiple peripheral I/O groups, plus a 12-bit 1 Msps ADC, four 16-bit timer/counters, two I2S/TDM interfaces, and a USB 2.0 Full-Speed device/host controller with on-chip transceiver. Architecturally, the SAM G53 uses a single AHB-Lite bus matrix connecting the Cortex-M4 core to Flash, SRAM, and peripherals through distinct bridges, with a DMA controller (channels for peripheral-to-memory, memory-to-memory, and peripheral-to-peripheral moves) reducing CPU load during data streaming. The integrated FPU accelerates single-precision signal-processing tasks such as audio decimation, sensor fusion, and PID loops in motor control, allowing software implementations that previously required a DSP. Typical applications include industrial control and sensor hubs, USB peripherals (HID, CDC, audio class), CAN-based building automation nodes, low-cost graphical HMI panels, and consumer audio devices. The 48MHz core and FPU also suit simple digital signal processing such as audio rate conversion, low-bandwidth motion estimation, and audio codec front-ends where deterministic latency matters. When designing with this part, plan for a 1.62V-3.6V supply rail with a 100nF + 4.7uF decoupling network placed close to the LQFP pins; the LQFP-100 pad layout allows easy 2-layer or 4-layer PCB implementation. Use the on-chip FPU for floating-point DSP but verify that the compiler emits hardware FPU instructions to gain the expected speedup over a Cortex-M3 equivalent. This page synthesizes distributor pricing, parametric drop-in alternatives sourced from the Microchip SAM G53 family, and practical design notes beyond a raw datasheet reprint.

RFQ संपर्क
ATSAMG54N19B-AU - 512KB Flash ARM Cortex-M4 MCU | Microchip
ATSAMG54N19B-AU

ATSAMG54N19B-AU - 512KB Flash ARM Cortex-M4 MCU | Microchip

The Microchip Technology ATSAMG54N19B-AU is a 32-bit ARM Cortex-M4 microcontroller in the SAM G54 family, featuring 512KB of Flash and 96MHz CPU clock speed in a 100-pin LQFP (14x14 mm) package. It is purpose-built for low-power connected and audio applications, integrating a Floating Point Unit (FPU), a Cryptographic engine (AES, TDES), and an audio PLL that supports professional audio clock rates. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O on one die. The ARM Cortex-M4 is a 32-bit RISC core with DSP extensions and an optional single-precision FPU. The ATSAMG54 sits in Microchip's SAM family between the Cortex-M0+ based SAM D series and the higher-end Cortex-M7 SAM E/S/V series, targeting ultra-low-power DSP and audio processing in always-listening devices. Key features include 96KB SRAM, a 12-bit 1MSPS ADC with up to 17 channels, two I2S interfaces, one HS USB 2.0 device port, up to six SERCOM (UART/SPI/I2C), and an extensive power-saving architecture with SleepWalking peripherals. The 100-pin LQFP (14x14 mm) variant exposes the maximum peripheral count of the SAM G54 family, making it the high-pin-count member suited to gateway and bridge designs. Architecturally, the device uses a Cortex-M4 core with a 3-stage pipeline, Thumb-2 instruction set, and embedded Trace Macrocell (ETM) for instruction trace. The SAM G54 supports four low-power modes (Wait, Sleep, Backup, Active) and consumes as little as 3 microamps in Backup mode with RTC running, enabling coin-cell or battery-powered deployments. Typical applications include audio front-end processing (beamforming, noise suppression, echo cancellation), USB audio peripherals, smart home sensor hubs, industrial HMI, and battery-powered IoT gateways. The integrated audio PLL eliminates an external audio clock IC in DAC/ADC designs, reducing BOM cost. When designing with this device, allocate the 100-pin LQFP layout to allow exposed-pad soldering of the thermal pad to the ground plane for improved power dissipation. Ensure decoupling with 100nF and 4.7uF bulk capacitors near VDDIN pins per the SAM G54 hardware design checklist. This page synthesizes distributor pricing, drop-in alternatives drawn from the SAM G54 family, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
ATSAMG55J19A-AU - 120MHz Cortex-M4 MCU 512KB Flash | Microchip
ATSAMG55J19A-AU

ATSAMG55J19A-AU - 120MHz Cortex-M4 MCU 512KB Flash | Microchip

The Microchip ATSAMG55J19A-AU is an ARM Cortex-M4 microcontroller with FPU in the SAM G55 family, integrating 512KB of Flash and 160KB of SRAM, running at up to 120MHz core clock, and housed in a 64-pin LQFP (10x10mm) package. It is engineered for audio and human-machine-interface (HMI) applications that require DSP-class signal processing at low active power, with on-chip peripherals including I2S, USB 2.0 Full-Speed, multiple USART/UART/SPI/TWI, a 12-bit ADC, and a 32-bit timer/counter block. According to the verified Microchip product page, new designs should consider Revision B ATSAMG55J19B; the ATSAMG55J19A-AU itself remains active and shipping, with Microchip noting it is the legacy revision. An ARM Cortex-M4 microcontroller is a 32-bit RISC processor core with an integrated single-precision floating-point unit (FPU), DSP extensions, and a nested vectored interrupt controller. It belongs to the hierarchy: Cortex-M4 -> ARM Cortex-M family -> 32-bit microcontroller (MCU) -> embedded processor -> semiconductor IC. The SAM G55 family specifically targets low-power audio and HMI applications through picoPower technology, integrating a high-performance DSP engine with energy-efficient peripherals suitable for always-on battery-powered devices. Key features include 512KB embedded Flash for program storage, 160KB SRAM (including 16KB backup SRAM with retention in deep sleep), I2S digital audio interface with sample-rate converter, USB 2.0 Full-Speed device/host, an external bus interface for memory expansion, and an integrated FPU that accelerates floating-point math. The device operates from 1.62V to 3.6V supply, supports -40C to +85C industrial temperature range, and includes multiple low-power modes including deep sleep at less than 7 uA with SRAM retention, waking within 3 us to active execution. Architecturally, the SAM G55 uses a single-cycle multiplier, hardware divide, and DSP extensions to deliver 1.25 DMIPS/MHz and 1.61 CoreMark/MHz throughput at 120MHz. The Cortex-M4 core is paired with a multi-layer bus matrix and tightly-coupled SRAM, eliminating wait states for most code execution. The audio-grade peripherals include a dedicated I2S controller with PDM and TDM support, enabling direct interfacing with digital MEMS microphones and audio DACs without external glue logic. Typical applications include Bluetooth/wired audio headsets, industrial HMI panels with touch and display, USB audio devices, smart-home voice front-ends, and portable instrumentation. The combination of FPU-accelerated DSP, low-power audio peripherals, and high-density memory makes it particularly well-suited for audio processing, sensor fusion, and battery-powered edge-compute tasks. Designers should note that Revision A (this part) is functionally complete but Microchip has transitioned new designs to Revision B ATSAMG55J19B, which provides silicon-level errata fixes; pin-for-pin compatibility between A and B revisions is preserved, so existing PCB layouts do not need to be changed when migrating. Verify long-term availability with your distributor before committing to Revision A in new designs. This page synthesizes distributor pricing, drop-in cross-reference data, and practical design notes that go beyond the manufacturer datasheet to help engineers select, source, and design with the ATSAMG55J19A-AU efficiently.

RFQ संपर्क
ATSAMG55J19A-MU - Cortex-M4 MCU 120MHz 512KB Flash 64-QFN | Microchip
ATSAMG55J19A-MU

ATSAMG55J19A-MU - Cortex-M4 MCU 120MHz 512KB Flash 64-QFN | Microchip

The Microchip Technology ATSAMG55J19A-MU is a 32-bit ARM Cortex-M4 microcontroller with FPU in the SAM G55 family, operating at up to 120 MHz with 512 KB of Flash and up to 176 KB of SRAM, packaged in a 64-pin QFN (7.5x7.5 mm). A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash and SRAM), and programmable peripherals. Within the broader hierarchy, the SAM G55 belongs to ARM Cortex-M4 microcontrollers -> 32-bit MCUs -> embedded microcontrollers -> integrated circuits. The Cortex-M4 with single-precision FPU enables efficient DSP and floating-point math for audio, motor control, and signal-processing tasks. Key features include up to 120 MHz CPU clock, 512 KB Flash, up to 176 KB SRAM, full-speed USB 2.0 with on-chip PHY, I2S audio interface for digital audio streaming, and picoPower technology delivering down to 100 uA/MHz active and below 7 uA in deep sleep with SRAM retention. Wake-up from deep sleep to first instruction is as fast as 3 us. The integrated FPU accelerates audio codecs and DSP workloads without external math processors. The SAM G55 architecture combines an MPU (Memory Protection Unit), hardware AES, and a flexible peripheral set including HS USB, USB on-the-go, up to two I2S/TDM interfaces, multiple UART/SPI/TWI, and a 12-bit ADC. Compared to Cortex-M0/M3 parts, the Cortex-M4 with FPU executes single-precision math in a single cycle, dramatically reducing CPU load for audio and motor-control algorithms. Typical applications include USB audio headsets and USB headphones, Bluetooth audio bridges, IoT edge nodes with USB connectivity, industrial sensor hubs, and low-power consumer audio products. The combination of USB 2.0 FS, I2S, and Cortex-M4 DSP makes it well suited to audio streaming tasks. Designers should pay attention to decoupling: place 100 nF + 4.7 uF ceramic capacitors near each VDD pin and keep the QFN exposed pad soldered to a continuous ground plane for thermal dissipation and signal integrity. This page synthesizes distributor pricing, drop-in alternatives drawn from the same SAM G55 family, and practical design notes not found in the manufacturer datasheet alone.

RFQ संपर्क
ATSAMG55J19A-MUT - 120MHz Cortex-M4 MCU 512KB Flash | Microchip
ATSAMG55J19A-MUT

ATSAMG55J19A-MUT - 120MHz Cortex-M4 MCU 512KB Flash | Microchip

The Microchip ATSAMG55J19A-MUT is a 32-bit ARM Cortex-M4 microcontroller with FPU running at up to 120MHz, integrating 512KB of Flash and 176KB SRAM in a 64-pin QFN (7.5x7.5mm) package. It is part of the SAM G55 audio-oriented family designed for high-performance DSP and floating-point audio processing tasks in industrial temperature ranges. An ARM Cortex-M4 microcontroller is a 32-bit RISC processor core with Thumb-2 instruction set, integrated single-precision IEEE 754 floating-point unit (FPU), and DSP extensions (single-cycle MAC, saturating arithmetic). It belongs to the Cortex-M family of embedded microcontrollers within the broader category of microcontrollers and microprocessors. The Cortex-M4 sits between the Cortex-M3 (no FPU) and Cortex-M7 (higher performance) in ARM's embedded hierarchy. Key features include 120MHz core clock with single-cycle MAC, hardware FPU for floating-point audio codecs, integrated Class-D amplifier interface support, I2S/TDM digital audio interfaces, and a full-speed USB 2.0 High-Speed PHY. The device supports 1.62V to 3.6V operating voltage and operates across the -40C to +85C industrial temperature range. It includes multiple communication peripherals: up to 7 UART/USART, 3 I2C, 6 SPI, and a high-speed USB port. The SAM G55 architecture integrates an audio-specific PLL (AUD PLL) for jitter-free I2S clocking, dual 12-bit 1Msps ADC modules with up to 16 channels, and hardware cryptographic accelerators. The 512KB Flash supports in-application programming, while the 176KB SRAM accommodates large audio buffers (WAV/MP3 decoding) without external memory. The 64-QFN package provides excellent thermal performance for the 120MHz operating envelope. Typical applications include smart speakers and voice assistants, professional audio equipment, headphone amplifiers with DSP, automotive infotainment audio, and industrial control with audio feedback. The integrated FPU enables real-time audio effect processing including EQ, dynamics, and noise suppression without CPU overload. When designing with this part, allocate the AUD PLL for low-jitter I2S clocking and ensure proper decoupling on VDDCORE pins. For new designs, Microchip recommends the Revision B variant (ATSAMG55J19B) which offers improved errata corrections. The Cortex-M4 DSP extensions (SIMD, MAC) significantly accelerate audio filter operations versus software-only Cortex-M3 designs.

RFQ संपर्क
ATSAMG55J19B-AUT - ARM Cortex-M4 MCU 120MHz 512KB LQFP-64
ATSAMG55J19B-AUT

ATSAMG55J19B-AUT - ARM Cortex-M4 MCU 120MHz 512KB LQFP-64

The Microchip Technology ATSAMG55J19B-AUT is a 32-bit ARM Cortex-M4 microcontroller with a single-precision floating-point unit (FPU) from the SAM G55 series, operating at up to 120 MHz with 512 KB of embedded Flash and 176 KB of SRAM, housed in a 64-pin LQFP (10x10 mm) package and rated for the industrial temperature range (-40C to +85C). The "-AUT" suffix denotes Tape-and-Reel packaging for high-volume assembly lines, while the "-B" silicon revision delivers enhanced peripheral performance versus the legacy "-A" revision. A 32-bit microcontroller (MCU) is a system-on-chip that integrates a CPU core, program memory, data memory, and a rich peripheral set into a single IC. The ARM Cortex-M4 architecture belongs to the Cortex-M family of low-power, deterministic processor cores designed for embedded and real-time applications; when augmented with an FPU it can execute single-precision floating-point instructions natively, which accelerates digital signal processing (DSP) and audio algorithm tasks without burdening the CPU with software emulation. Within Microchip's product hierarchy this part sits inside the SAM family -> Cortex-M4 class -> performance-oriented sub-family with FPU, supporting the broader Atmel/Microchip ecosystem including the SAM4S, SAM D5x/E5x, and SAME70 lines. Key features include a Cortex-M4 core with FPU, 120 MHz maximum clock speed, 512 KB Flash, 176 KB SRAM, 16-bit PWM timers, an I2S digital audio interface, a full-speed USB 2.0 device/host with on-chip PHY, a 12-bit ADC, and flexible serial peripherals (USART, SPI, TWI/I2C). Power-saving features include Sleep, Wait, and Backup modes plus a low-power RTC. These attributes make the SAM G55 a strong fit for connected audio, sensor hubs, and industrial control applications. The SAM G55 silicon uses a Cortex-M4 with Thumb-2 instruction set, hardware single-cycle multiply-accumulate, and a tightly-coupled SRAM block for deterministic interrupt latency. The 120 MHz clock supports 1.25 DMIPS/MHz (1.50 DMIPS/MHz with the optional FPU DSP extensions) per the Dhrystone benchmark, and the wide peripheral DMA architecture enables high-throughput data movement between I2S, USB, ADC, and SRAM without CPU intervention. Typical applications include USB audio headsets, smart speakers, voice-controlled appliances, industrial sensor hubs, HMI controllers, and wireless audio base stations. The wide operating temperature range and tape-and-reel packaging further support deployment in mass-produced industrial and consumer audio products. When designing with the ATSAMG55J19B-AUT, plan the PCB layout for proper USB impedance control (90 ohm differential), keep the VDDCORE decoupling within 5 mm of the LQFP-64 pin, and use the on-chip FPU instead of software floating-point libraries to maximize throughput for DSP workloads. This page synthesizes distributor pricing, drop-in alternatives from the SAM G55 series and cross-brand Cortex-M4 candidates, plus practical design notes that go beyond the manufacturer datasheet summary to help engineers select and qualify this MCU.

RFQ संपर्क
ATSAMG55J19B-MUT - 120MHz Cortex-M4 MCU, 512KB Flash | Microchip
ATSAMG55J19B-MUT

ATSAMG55J19B-MUT - 120MHz Cortex-M4 MCU, 512KB Flash | Microchip

The Microchip Technology ATSAMG55J19B-MUT is a 32-bit ARM Cortex-M4 microcontroller with FPU running at up to 120 MHz, integrating 512 KB of Flash and 176 KB of SRAM in a 64-pin 7.5x7.5 mm QFN package. It is part of the SAM G55 family, purpose-built for audio and low-power signal-processing applications that benefit from DSP extensions and single-precision floating point acceleration. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals including timers, communication interfaces, ADC/DAC blocks, and GPIOs. In the taxonomy of embedded semiconductors, the SAM G55 belongs to the Cortex-M4 family (ARMv7-M architecture with FPU and DSP) -> ARM Cortex-M microcontrollers -> 32-bit microcontrollers -> microcontrollers -> embedded processors -> semiconductors. The Cortex-M4 with FPU executes DSP algorithms (FFT, FIR, biquad filters) and audio codecs efficiently while preserving the deterministic interrupt model required for real-time audio. Key features of the ATSAMG55J19B-MUT include the Cortex-M4 core with single-precision FPU, 512 KB Flash with single-cycle access at full speed, 176 KB SRAM, an embedded boot loader, an embedded voltage regulator for single-supply operation, power-on reset (POR), brown-out detector, watchdog timer, three on-chip RC oscillators, and a 3 to 20 MHz quartz/ceramic resonator interface. It supports USB 2.0 Full-Speed with on-chip transceiver, I2S/SSC audio interfaces, and up to 47 GPIO lines. The architecture combines Cortex-M4 DSP extensions with audio-oriented peripherals such as an I2S/SSC controller and a Class-D amplifier-friendly PWM, optimized for headset, headphone, and portable-audio products. Active power consumption is minimized via Sleep, Deep-Sleep, and Backup modes with RTC retention, while the integrated FPU lets audio DSP work finish faster, allowing the chip to return to sleep quickly and reduce overall energy use. Typical applications include Bluetooth/USB audio headsets, sound bars, portable speakers, hearing aids, industrial audio front-ends, voice-over-IP peripherals, and any low-power DSP audio product. The combination of Cortex-M4 DSP, ample SRAM for buffer management, and built-in audio interfaces makes the SAM G55 a strong fit for streaming-audio DSP. When designing with this part, ensure that decoupling (100 nF + bulk) is placed as close as possible to the four VDD pins and that the exposed pad (EP) of the QFN package is soldered to a continuous ground plane for thermal dissipation and low-impedance return. Configure unused pins as inputs with pull-ups to avoid spurious interrupts during reset.

RFQ संपर्क
ATSAMHA0E14A-MZT-BVAO - 32-bit M0+ LIN SiP MCU 16KB Flash | Microchip
ATSAMHA0E14A-MZT-BVAO

ATSAMHA0E14A-MZT-BVAO - 32-bit M0+ LIN SiP MCU 16KB Flash | Microchip

The Microchip Technology ATSAMHA0E14A-MZT-BVAO is a 32-bit Arm Cortex-M0+ based LIN System-in-Package (SiP) integrating an automotive MCU, an ATA663231 LIN transceiver, and a voltage regulator (VREG) into a single 32-pin VQFN (5x5 mm) package. The device operates at up to 48 MHz and delivers 2.46 CoreMark/MHz, with 16 KB of Flash, 0.5 KB of read-while-write data flash, and 4 KB of SRAM, targeting compact, AEC-Q100 qualified automotive body and sensor node designs. A System-in-Package (SiP) is a multi-die module that combines an MCU and one or more companion ICs (here a LIN physical-layer transceiver plus an internal regulator) inside a single IC package. In the power-management IC hierarchy, this product sits at the topmost tier of integrated motor/sensor subsystems - eliminating the discrete LIN transceiver and external LDO that designers would otherwise pair with a stand-alone Cortex-M0+ MCU. The M0+ core itself is the most energy-efficient member of the Cortex-M family, and combining it with a LIN transceiver drastically shrinks the BOM, simplifies PCB layout, and improves EMC behavior for in-vehicle networking. Key features include 32 pins total, an integrated LIN 2.x physical-layer transceiver compliant with SAE J2602, 16 KB of in-system programmable Flash, 4 KB SRAM, support for up to 48 MHz CPU clock, and a wide automotive temperature range. AEC-Q100 qualification plus functional-safety (FuSa) support position the part for safety-relevant automotive sub-systems, where single-chip integration reduces both board area and the number of potential fault points that require ASIL analysis. The device combines an ARM Cortex-M0+ core with on-chip Flash and SRAM, the ATA663231 LIN transceiver from Microchip's automotive connectivity portfolio, and an internal 3.3 V or 5 V VREG that can power the MCU from the vehicle's 12 V battery rail. The integrated regulator supports direct battery supply, and the LIN bus pin meets the dominant/recessive timing required by SAE J2602 and ISO 17987 LIN specifications. Functional-safety documentation is available to assist customers building ISO 26262-compliant nodes. Typical applications include automotive body control modules, HVAC sensor nodes, seat-control and lighting slaves, window lift and door module ECUs, and other LIN-slave end nodes in in-vehicle networks. The single-package integration also suits space-constrained mechatronic sensors that previously required a stand-alone MCU plus a discrete LIN transceiver PCB footprint. When designing with this SiP, note that the LIN bus pin requires an external pull-up and ESD/EMI protection per OEM hardware guidelines, and PCB layout must keep the RF-sensitive LIN traces short and reference a solid ground pour. Designers migrating from a discrete MCU + ATA663231 design can reuse firmware, although the integrated VREG eliminates the external LDO footprint.

RFQ संपर्क
ATSAMHA0E16A-MZT-BVAO - LIN SiP 32KB Cortex-M0+ MCU | Microchip
ATSAMHA0E16A-MZT-BVAO

ATSAMHA0E16A-MZT-BVAO - LIN SiP 32KB Cortex-M0+ MCU | Microchip

The Microchip Technology ATSAMHA0E16A-MZT-BVAO is a low-power automotive LIN System-in-Package (SiP) integrating an Arm Cortex-M0+ MCU with a LIN transceiver and voltage regulator in a single 32-pin VQFN (5x5 mm) package. The device delivers 48 MHz CPU performance with 64 KB Flash, 8 KB SRAM, and 2 KB read-while-write data flash for automotive body and sensor applications. A System-in-Package (SiP) combines multiple silicon dies inside one package to deliver a complete functional subsystem, reducing PCB area and BOM cost versus discrete MCU + LIN + LDO designs. Within Microchip's portfolio, the ATSAMHA0 family sits in the LIN-attached body-electronics segment, providing automotive Grade-0 capable Cortex-M0+ compute plus LIN physical-layer connectivity in a single AEC-Q100 qualified IC. Key features of this part include 64 KB of Flash (64K x 8), 8 KB SRAM, 32 general-purpose I/O lines, an integrated LIN 2.x/SAE J2602 transceiver, an internal 3.3V LDO, a 12-bit ADC up to 10 channels, configurable SERCOM interfaces, and RTC with calendar. AEC-Q100 Grade 1 qualification supports automotive deployments, and the part operates over -40C to +105C. The SAM HA0 core uses a single-cycle Cortex-M0+ pipeline with a 48 MHz maximum CPU clock, achieving 0.9 DMIPS/MHz. Integrated LIN transceiver and LDO eliminate external PHY and regulator components, enabling compact ECU modules. The 12-bit 350 ksps ADC, multi-mode timers, and SERCOM peripherals support PWM motor control, sensor signal acquisition, and LIN-based body network nodes. Typical applications include automotive body controllers, HVAC control modules, mirror and seat controllers, LED lighting modules, sensor interfaces, and industrial sensor nodes requiring LIN connectivity. The wide operating range and AEC-Q100 qualification make it suitable for under-hood and cabin-mounted ECUs in passenger and commercial vehicles. When designing with this SiP, follow the recommended LIN bus termination and ESD protection guidelines from the Microchip datasheet. Place bypass capacitors close to each supply pin and route the LIN pin with controlled impedance and proper shielding to meet automotive EMC requirements. Use the on-chip LDO for MCU core supply and decouple digital and analog domains to minimize noise coupling. This page consolidates distributor pricing, AEC-Q100 qualified drop-in alternatives, and practical design guidance not assembled in the standalone Microchip datasheet, providing a focused selection reference for automotive LIN node designers.

RFQ संपर्क
ATSAMHA0G16A-MZT-BVAO - 48MHz ARM M0+ LIN SiP 64KB Flash | Microchip
ATSAMHA0G16A-MZT-BVAO

ATSAMHA0G16A-MZT-BVAO - 48MHz ARM M0+ LIN SiP 64KB Flash | Microchip

The Microchip ATSAMHA0G16A-MZT-BVAO is a low-power automotive System-in-Package (SiP) combining a 32-bit ARM Cortex-M0+ microcontroller with an integrated LIN transceiver and voltage regulator, housed in a 48-pin VQFN (7x7 mm) package with exposed thermal pad. The SAM HA0G16A device operates at up to 48 MHz, delivers 2.46 CoreMark/MHz, and integrates 64 KB of Flash, 2 KB of read-while-write data Flash, and 8 KB of SRAM. The part carries the -BVAO suffix denoting the automotive-grade, tape-and-reel packaging variant and is qualified to AEC-Q100 standards for automotive LIN nodes. A System-in-Package (SiP) integrates multiple silicon dies and passive components inside a single IC package, dramatically reducing PCB footprint versus discrete MCU + LIN SBC solutions. In the LIN (Local Interconnect Network) sub-bus automotive hierarchy, the SiP sits below CAN nodes and provides the physical-layer transceiver, voltage regulation, and application processing for body-control modules. The ATSAMHA0G16A-MZT-BVAO belongs to Microchip's SAM HA0 family, purpose-built for LIN slave nodes in body electronics such as door modules, seat controllers, mirror adjusters, and lighting clusters. Compared with a discrete MCU plus external LIN SBC, this SiP reduces BOM count by approximately 30% and shortens EMC qualification cycles because the LIN bus is already characterized inside the package. Key features include 48 MHz Cortex-M0+ core, 64 KB Flash, 8 KB SRAM, 2 KB data Flash, integrated LIN 2.x/SAE J2602 transceiver, on-chip 5V/3.3V LDO voltage regulator, AEC-Q100 qualification, 48-VQFN exposed-pad package, and functional safety (FuSa) support. The SiP is rated for -40C to +115C (TC) operation and supports automotive temperature grade 1 environments. Functional-safety features enable integration into ASIL-A and ASIL-B capable systems when paired with an external watchdog MCU. Architecturally, the SAM HA0G16A-MZT-BVAO separates the digital die (MCU core, Flash, SRAM, peripherals) from the analog/power die (LIN SBC, voltage regulator) inside a single molded-array package. This partition lets the LIN transceiver tolerate 40V load-dump transients while the MCU core runs on a clean regulated rail. The Cortex-M0+ delivers 0.93 DMIPS/MHz - lower than Cortex-M4F but adequate for deterministic LIN message processing at 19.2 kbps. On-chip peripherals include timers, ADC, and SERCOM-style USART for diagnostic and sensor I/O. Typical applications include automotive LIN slave body-control modules, LED lighting controllers, HVAC flap drivers, window-lift switches, seat-position sensors, and smart-sensor LIN nodes. The SiP form factor is especially attractive for space-constrained modules behind door panels or inside headlamp assemblies. AEC-Q100 Grade 1 qualification allows direct deployment under the hood or in passenger compartments without additional derating. According to the Microchip SAM HA0 family datasheet, the LIN SBC integrates a low-dropout regulator capable of sourcing the MCU core plus external sensor loads up to 70 mA continuous. Design consideration: the exposed thermal pad must be soldered to a continuous copper pour of at least 25 mm^2 on a four-layer PCB to keep junction temperature within the 115C TC limit. Inadequate thermal relief forces the LIN regulator to enter thermal fold-back during sustained LIN bus dominant states. Place a 100 nF decoupling capacitor within 2 mm of the VDDIO pin and a 4.7 uF bulk capacitor on the LIN VBB pin to meet SAE J2602 bus transient requirements. This page synthesizes distributor pricing, AEC-Q100 context, LIN SBC integration notes, and drop-in alternatives not found in a quick datasheet scan - it gives the design engineer a 360-degree view that a single product page cannot.

RFQ संपर्क
ATSAMHA1E14A-MBT-B510 - LIN SiP MCU+TRX+VREG 32-VQFN | Microchip
ATSAMHA1E14A-MBT-B510

ATSAMHA1E14A-MBT-B510 - LIN SiP MCU+TRX+VREG 32-VQFN | Microchip

The Microchip Technology ATSAMHA1E14A-MBT-B510 is a 32-bit Arm Cortex-M0+ based automotive LIN System-in-Package (SiP) that integrates an MCU, a LIN transceiver, and a voltage regulator inside a single 32-pin VQFN (5x5 mm) package. It operates at up to 48 MHz with 16 KB of Flash, 0.5 KB of read-while-write data Flash, and 4 KB of SRAM, and is qualified to AEC-Q100 for automotive body electronics and in-cabin LIN nodes. The device belongs to Microchip's SAM HA1 family of low-power, AEC-Q100 qualified microcontrollers targeted at automotive LIN slave and master applications. A LIN System-in-Package (SiP) is an integrated module that combines a microcontroller, a LIN (Local Interconnect Network) physical-layer transceiver compliant with ISO 17987, and an on-chip voltage regulator into one package. The SiP approach eliminates the need for designers to source and qualify separate MCU and LIN transceiver ICs, reduces BOM count, simplifies PCB layout, and shortens the time to achieve LIN conformance certification. LIN is a low-cost, single-wire, master-slave serial protocol used widely in automotive body domains where CAN bandwidth is unnecessary. Key differentiating features of the ATSAMHA1E14A-MBT-B510 include AEC-Q100 Grade 1 qualification for -40C to +125C operation, an integrated LIN 2.x/SAE J2602 transceiver, on-chip LDO for direct 12V automotive bus operation, 16 KB self-programmable Flash, four KB SRAM, and 32-VQFN packaging with wettable flanks for automated optical inspection. The Cortex-M0+ core consumes as little as 50 uA/MHz active, supporting always-on body modules that must wake on LIN bus activity. Architecturally, the device pairs the Cortex-M0+ core with Microchip's peripheral touch (PTC), SERCOM, and Event System IP blocks. The integrated LIN transceiver handles bus dominant/recessive arbitration, slew-rate control, and thermal shutdown independently of the MCU, allowing the LIN interface to remain active even when the core is in deep sleep. Functional Safety (FuSa) support assists developers building ISO 26262 ASIL-A-capable systems. Typical applications include automotive window lifters, seat controllers, mirror adjusters, sunroof modules, HVAC damper actuators, ambient lighting, rain/light sensors, and other body-electronics nodes that communicate via LIN bus to a central body control module. The 32-VQFN package with wettable flanks supports high-yield automotive PCB assembly lines. When designing with this SiP, route the LIN bus pin directly to the bus with proper ESD and reverse-battery protection, and follow Microchip's LIN PCB layout guidelines for EMC compliance. Always validate the full node against the target LIN conformance specification (ISO 17987, SAE J2602, or LIN 2.2a) before production release.

RFQ संपर्क
ATSAMHA1E14A-MBT-BVAO - LIN SiP MCU 48MHz 16KB Flash | Microchip
ATSAMHA1E14A-MBT-BVAO

ATSAMHA1E14A-MBT-BVAO - LIN SiP MCU 48MHz 16KB Flash | Microchip

The Microchip Technology ATSAMHA1E14A-MBT-BVAO is a low-power automotive LIN System-in-Package (SiP) that integrates an Arm Cortex-M0+ MCU with an on-chip LIN transceiver and a voltage regulator in a single 32-pin VQFN (5x5 mm) package with exposed pad. The SAM HA1E14A core is a 32-bit single-core microcontroller operating up to 48 MHz, delivering 2.46 CoreMark/MHz, with 16 KB of Flash, 0.5 KB of read-while-write data flash, and 4 KB of SRAM, all qualified to AEC-Q100 for automotive applications including functional safety (FuSa) use cases. A LIN System-in-Package (SiP) is a compact multi-die module that combines a microcontroller, a LIN physical-layer transceiver, and a power-regulation block in one surface-mount package. The LIN (Local Interconnect Network) standard is a low-cost, single-wire serial protocol widely used in automotive body and chassis electronics for non-critical body control modules such as mirror adjusters, seat controllers, window lifters, and sensor clusters; the SiP form factor reduces board space, BOM count, and EMI exposure compared to discrete MCU-plus-transceiver designs. Key features include integrated LIN transceiver compliant with LIN 2.x and SAE J2602, an on-chip LDO for direct 12 V battery rail operation, AEC-Q100 Grade 1/2 qualification, functional-safety ready architecture, and the SAM HA1 peripheral set with timers, ADC, and SERCOM channels. The 32-VQFN exposed pad provides a low thermal-resistance footprint suitable for under-hood and behind-dashboard mounting. The device uses the Cortex-M0+ core with the standard SAM D peripheral ecosystem, enabling code portability across the SAM family and supporting the MPLAB X IDE with Microchip's Atmel Studio toolchain. The integrated LIN transceiver eliminates external PHY circuitry, reducing BOM cost and PCB area for body-electronics modules. Functional Safety (FuSa) features support ISO 26262 development at the application layer. Typical applications include automotive body control modules (BCM), LIN sensor nodes (rain/light/temperature), seat and mirror controllers, HVAC flap actuators, window lifters, and lighting controls. Designers choose this part when they need a single-chip LIN node with AEC-Q100 qualification and minimal PCB footprint. When designing with this SiP, observe the LIN bus ESD and load-dump requirements; ensure the exposed pad is soldered with adequate thermal vias for heat extraction, and follow Microchip's LIN application note for the external pull-up and master/slave termination network. This page synthesizes distributor pricing, drop-in same-brand alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
ATSAMHA1E15A-MBT-BVAO - ARM Cortex-M0+ LIN SiP MCU | Microchip
ATSAMHA1E15A-MBT-BVAO

ATSAMHA1E15A-MBT-BVAO - ARM Cortex-M0+ LIN SiP MCU | Microchip

The Microchip Technology ATSAMHA1E15A-MBT-BVAO is a low-power automotive System-in-Package (SiP) integrating a 32-bit ARM Cortex-M0+ microcontroller, a LIN transceiver, and a voltage regulator in a single 32-pin VQFN (5x5 mm) package. It operates at up to 48 MHz, delivers 2.46 CoreMark/MHz, and includes 32 KB of Flash, 4 KB of SRAM, and 1 KB of read-while-write data Flash. A System-in-Package (SiP) is a modular packaging technique that places multiple active die inside one IC package, allowing heterogeneous functions (analog, digital, mixed-signal, power) to coexist on a small footprint. Within the broader microcontroller hierarchy, the ATSAMHA1E15A sits at the intersection of automotive microcontroller -> ARM Cortex-M0+ MCU -> LIN node controller -> system-in-package, and it belongs to the AEC-Q100-qualified SAM HA1 functional-safety family. Integrating the LIN transceiver and VREG eliminates two external ICs that would normally occupy PCB area around a discrete MCU. Key features include 19 GPIO lines, hardware PWM channels, ADC, DAC, DMA, and an operating voltage range of 2.7 V to 3.63 V (nominal 3.3 V). The device targets automotive body-control and sensor-node applications with industrial temperature grade (-40 °C to +105 °C) and AEC-Q100 / TS 16949 screening. Functional safety (FuSa) documentation is available to support ASIL-classified systems, simplifying ISO 26262 design workflows. The on-chip LIN transceiver is compliant with LIN 2.x and SAE J2602, supporting master and slave node roles up to 20 kbit/s. The integrated VREG accepts a 5 V to 28 V battery feed and produces a clean 3.3 V rail for the MCU core. This co-integration cuts BOM cost, reduces PCB area by approximately 30-40 % versus discrete designs, and removes the need for an external LIN phy IC. Typical applications include automotive body-control modules (BCM), HVAC blower and flap controllers, door/window/seat switches, LED lighting nodes, sensor interfaces, and LIN-based actuator drivers. The AEC-Q100 qualification and wide battery-tolerant input make the part drop-in suitable for 12 V automotive systems where LIN is the physical bus. When designing with this SiP, place the required bypass capacitors within 2 mm of the VREG and MCU supply pins. Use Microchip Studio and Atmel START to generate peripheral drivers; the LIN stack is provided via the Microchip LIN Stack. Verify EMC behavior with the SAM HA1 EMC checklist before finalizing PCB layout. This page synthesizes current distributor pricing, drop-in alternative candidates, and practical design notes not consolidated in the manufacturer datasheet, accelerating part selection for automotive LIN node designs.

RFQ संपर्क
ATSAMHA1E16A-MBT-B510 - 48MHz LIN SiP AEC-Q100 MCU | Microchip
ATSAMHA1E16A-MBT-B510

ATSAMHA1E16A-MBT-B510 - 48MHz LIN SiP AEC-Q100 MCU | Microchip

The Microchip ATSAMHA1E16A-MBT-B510 is an automotive AEC-Q100-qualified 32-bit ARM Cortex-M0+ system-in-package (SiP) that integrates a microcontroller, a LIN transceiver, and a voltage regulator in a single 32-VQFN (5x5 mm) package. The device operates at up to 48 MHz with 64 KB of Flash (32K x 16), 2 KB of read-while-write data flash, and 8 KB of SRAM, delivering LIN-bus-capable processing with the lowest external component count in the SAM family. According to the Microchip datasheet introduction, the SAM HA0/1 family is the lowest-power automotive SiP product line built around the Cortex-M0+ core with LIN System Basis Chip (SBC) functionality. A System-in-Package (SiP) combines multiple silicon dies in one package to deliver the function of two or three discrete ICs in the footprint of one. The ATSAMHA1E16A integrates the MCU die, an ATA663231-class LIN physical-layer transceiver, and an LDO voltage regulator; this architecture gives LIN-node designers a single-part BOM while still keeping the analog/digital isolation required for in-vehicle networks. Compared with a discrete MCU+LIN+LDO solution, the SiP approach reduces PCB area, simplifies EMC layout, and shortens functional-safety (FuSa) qualification work. Key features include 64 KB Flash, 8 KB SRAM, a 48 MHz Cortex-M0+ core, integrated LIN 2.x/SAE J2602 transceiver with up to 20 kbaud bus communication, integrated 5V/3.3V selectable VREG, AEC-Q100 Grade 1 qualification for -40C to +125C operation, Functional Safety documentation, and a 32-pin VQFN package that exposes GPIO, LIN bus, VBAT, VCC, and ground pins. The SiP also integrates ESD protection on LIN, and a low-power standby mode for ECU sleep/wake-up scenarios. Typical applications include automotive body electronics LIN nodes such as window lift, seat control, mirror adjust, ambient lighting, HVAC flaps, and rain/light sensors. The integrated LIN SBC function makes it ideal as a satellite ECU connected directly to the vehicle's LIN bus, replacing discrete MCU + LIN PHY + LDO designs. The SAM HA1E16A AEC-Q100 qualification also simplifies PPAP and ISO 26262 documentation for OEM platforms. When designing with this SiP, treat the LIN bus pinout (LIN, VBAT, VCC) as a matched impedance link and keep the LIN trace short with a strong ground pour to meet automotive EMC requirements. Use the internal VREG output to power the MCU die and external low-current circuitry; for higher-current external loads, add a separate post-regulator. The exposed pad of the VQFN-32 must be soldered to a sufficiently large copper island to dissipate the LIN bus fault-mode heat. This page synthesizes distributor pricing, same-family alternatives, and automotive LIN design notes not found in the manufacturer datasheet introduction.

RFQ संपर्क
ATSAMHA1E16A-MBT-BVAO - 64KB LIN SiP MCU Cortex-M0+ | Microchip
ATSAMHA1E16A-MBT-BVAO

ATSAMHA1E16A-MBT-BVAO - 64KB LIN SiP MCU Cortex-M0+ | Microchip

The Microchip Technology ATSAMHA1E16A-MBT-BVAO is a low-power automotive System-in-Package (SiP) device integrating an ARM Cortex-M0+ microcontroller core with an on-board LIN transceiver and voltage regulator. It runs at up to 48 MHz, delivers 2.46 CoreMark/MHz, and ships in a 32-pin VQFN (5x5 mm) package with an exposed thermal pad. A LIN System-in-Package combines a microcontroller core, a physical-layer LIN transceiver, and an integrated voltage regulator on a single substrate. This integration reduces external BOM count, simplifies PCB layout, and is purpose-built for in-vehicle networks where a node must communicate over a single-wire LIN bus while remaining powered from the vehicle's 12 V bus. Within the broader hierarchy, an SiP belongs to the microcontroller family, which itself sits inside the broader power-managed automotive embedded IC category. The device features 64 KB of Flash, 2 KB of read-while-write data Flash, 8 KB of SRAM, and runs from a single 3.3 V supply. AEC-Q100 qualification supports automotive deployment, and the functional-safety (FuSa) architecture targets ISO 26262-capable body and chassis applications. The integrated LIN 2.x transceiver plus on-chip LDO removes the need for an external PHY, while the Cortex-M0+ core ensures deterministic real-time response. Typical applications include LIN slave nodes such as body control modules, seat controllers, mirror adjusters, HVAC damper drivers, RKE receivers, ambient lighting drivers, and small sensor clusters. The Cortex-M0+ core's 2.46 CoreMark/MHz provides ample headroom for low-rate sensor conditioning and LIN message handling. Compared to a discrete MCU plus external LIN transceiver design, the SiP approach typically cuts board area by 30-50% and lowers standby current by eliminating redundant bias chains. When designing with this part, route the LIN bus pin directly to the connector with a minimum 2 kV ESD protection network if the bus is exposed. Place the SiP's exposed pad on a continuous ground copper pour with at least 16 thermal vias to keep junction temperature within the -40C to +105C automotive Grade-1 range. The integrated LIN transceiver handles bus dominant/recessive state transitions, so the firmware stack only needs to manage the UART-to-LIN framing. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical PCB layout guidance not aggregated on the manufacturer datasheet, giving automotive hardware engineers a single source for selection and supply-chain decisions.

RFQ संपर्क
ATSAMHA1G14A-MBT - LIN SiP MCU Cortex-M0+ 48MHz 16KB | Microchip
ATSAMHA1G14A-MBT

ATSAMHA1G14A-MBT - LIN SiP MCU Cortex-M0+ 48MHz 16KB | Microchip

The Microchip ATSAMHA1G14A-MBT is a low-power automotive System-in-Package (SiP) integrating an ARM Cortex-M0+ microcontroller, a LIN transceiver, and a voltage regulator in a single 48-pin VQFN (7x7 mm) package. The MCU core runs at up to 48 MHz with 16 KB of Flash, 4 KB of SRAM, and 0.5 KB of read-while-write data Flash. The integrated LIN SBC (System Basis Chip) blocks eliminate the need for an external LIN transceiver and LDO, reducing BOM count for body electronics modules. A System-in-Package (SiP) combines multiple silicon dies in one package to deliver a complete functional subsystem. In the SAM HA1 family, the SiP pairs an automotive-grade Cortex-M0+ MCU die with a LIN 2.x/SAE J2602 transceiver die and a 3.3V/5V linear regulator, enabling single-chip LIN nodes for body and chassis ECUs. This approach sits within the broader hierarchy of integrated circuits -> microcontrollers -> automotive MCUs -> LIN-capable SBC-MCU combinations. Key features include 48 MHz maximum CPU clock, hardware LIN 2.x/SAE J2602 transceiver compliance, integrated 3.3V/5V VREG, AEC-Q100 automotive qualification, 0.5 KB RWW data Flash for EEPROM emulation, and 4 KB SRAM. The device supports 48 GPIO and offers peripheral touch (PTC) plus multiple SERCOM, ADC, and timer channels. Low-power Sleep and Idle modes with fast wake-up make it ideal for always-on automotive body networks where quiescent current is critical. The SiP architecture is built around a 32-bit Cortex-M0+ core with single-cycle I/O access, supporting the Thumb-2 instruction set for compact code density. The LIN SBC die integrates physical layer transceiver, watchdog, and voltage regulator, while the MCU die provides digital control loops, diagnostics, and communication protocol stack (typically LIN LDF-driven). Together they meet ISO 17987 LIN physical layer and ISO 26262 functional safety (FuSa) targets when used with appropriate firmware. Typical applications include automotive body control modules, HVAC switch panels, seat control ECUs, door/window lift modules, steering column switches, and LIN slave nodes in interior lighting. The AEC-Q100 qualification and integrated LIN make it purpose-built for OEMs consolidating wiring harness content into compact LIN nodes. When designing with the ATSAMHA1G14A-MBT, ensure the LIN bus pull-up and master/slave termination are configured per SAE J2602. The wide 5V to 27V (40V transient) battery operation handled by the SBC die, combined with the MCU's low-power modes, allows direct connection to the 12V automotive battery rail without additional protection circuitry for typical body electronics. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, supporting component selection engineers evaluating LIN node MCU choices.

RFQ संपर्क
ATSAMHA1G14A-MBT-BVAO - Automotive LIN SiP MCU 32KB Flash | Microchip
ATSAMHA1G14A-MBT-BVAO

ATSAMHA1G14A-MBT-BVAO - Automotive LIN SiP MCU 32KB Flash | Microchip

The Microchip Technology ATSAMHA1G14A-MBT-BVAO is an automotive-grade LIN System-in-Package (SiP) integrating a 32-bit Arm Cortex-M0+ MCU with a LIN transceiver and a voltage regulator in a single 48-pin VQFN (7x7 mm) package. It operates at a CPU clock speed of 48 MHz and is built around the SAM HA1 family, which is AEC-Q100 qualified for automotive body electronics applications. The device includes 16 KB of Flash, 0.5 KB of read-while-write data Flash, and 4 KB of SRAM, with Functional Safety (FuSa) support. A System-in-Package (SiP) is a single component that integrates multiple bare dies into one molded package, allowing the combined silicon to behave like one IC. In the ATSAMHA1G14A-MBT-BVAO the MCU die, LIN SBC (System Basis Chip) die, and LDO die are co-packaged, saving PCB area and BOM cost versus a discrete MCU plus external LIN transceiver design. The SAM HA1 family sits within the broader Automotive MCU hierarchy: Cortex-M0+ -> SAM family -> SAM HA1 sub-family -> automotive body-comfort SiPs. Key features of this part include a -40C to +105C (or +125C) operating temperature range, integrated LIN 2.x/SAE J2602 transceiver, integrated 5V or 3.3V LDO, up to 48 MHz Cortex-M0+ core, and 16 KB Flash. The exposed-pad VQFN-48 (7x7 mm) package provides a low thermal resistance path, essential for automotive under-hood and body-control environments. FuSa documentation supports ISO 26262 system-level integration. Architecturally the device couples the Cortex-M0+ core's Thumb-2 instruction efficiency with a peripheral set that includes timers, ADC, I2C, SPI, USART, and a LIN-capable UART. The integrated LIN SBC handles bus dominant/recessive state decoding, slope control, and thermal shutdown, reducing firmware load. Typical applications include automotive body control modules, HVAC control panels, seat-control switches, mirror adjusters, lighting nodes (LIN-driven), and wiper/door modules. The wide operating range also suits industrial sensor nodes and HVAC fan controllers. When designing with this SiP, follow Microchip's LIN SBC layout guidelines: keep the LIN bus trace short, place a reverse-polarity and TVS protection diode near the bus pin, and provide a stable VBAT input with bulk decoupling of at least 10 uF plus 100 nF close to the VLIN pin.

RFQ संपर्क
ATSAMHA1G17A-MZT-BVAO - LIN SiP MCU+Cortex-M0+ 128KB | Microchip
ATSAMHA1G17A-MZT-BVAO

ATSAMHA1G17A-MZT-BVAO - LIN SiP MCU+Cortex-M0+ 128KB | Microchip

The Microchip ATSAMHA1G17A-MZT-BVAO is an AEC-Q100 qualified automotive LIN System-in-Package (SiP) integrating a 32-bit Arm Cortex-M0+ microcontroller, a LIN 2.x/SAE J2602 transceiver, and a 5V LDO voltage regulator into a single 48-pin VQFN (7x7 mm) package. It operates at a maximum clock speed of 48 MHz, achieving 2.46 CoreMark/MHz, and provides 128 KB of Flash, 4 KB of read-while-write data Flash, and 16 KB of SRAM. The 'MZT' ordering code denotes the 48-VQFN EP package shipped in tape-and-reel with the automotive-grade V temperature range (-40C to +125C). A LIN System-in-Package (SiP) is a multi-die module that combines an MCU core, a LIN physical-layer transceiver, and a power-management LDO in a single footprint, eliminating the need for designers to source, qualify, and lay out three separate ICs. The LIN bus standard (ISO 17987 / SAE J2602) is the dominant low-cost in-vehicle networking protocol for non-safety body-electronics sub-networks such as mirror modules, seat controllers, HVAC flaps, ambient lighting, and door-handle sensors. Integrating the transceiver on-die drastically reduces BOM count, PCB area, and EMC risk. Key features of the ATSAMHA1G17A-MZT-BVAO include an integrated LIN 2.x transceiver compliant with SAE J2602-2, an integrated 5V/3.3V LDO supporting direct 12V battery operation, 128 KB Flash / 16 KB SRAM memory, and an operating temperature range of -40C to +125C qualified to AEC-Q100 Grade 1. The 48-VQFN EP package with exposed pad provides a low thermal resistance path and a compact 7x7 mm footprint suitable for space-constrained automotive ECUs. The device targets LIN slave-node body-electronics applications where PCB area and BOM cost dominate the design budget. Typical end products include automotive mirror modules, seat-control units, HVAC flap actuators, ambient-lighting drivers, door-handle sensors, and sunroof controllers. The integrated LIN transceiver handles bus dominant/recessive state transitions with hardware-controlled slew-rate limiting, offloading protocol timing from the Cortex-M0+ core. When designing with the ATSAMHA1G17A-MZT-BVAO, the integrated 5V LDO is powered directly from the 12V vehicle battery (with external reverse-battery and load-dump protection), and the on-die LIN transceiver connects to the bus through a series resistor and an ESD diode. The exposed pad must be soldered to a sufficient copper pour to meet the AEC-Q100 Grade 1 thermal requirements. This page synthesizes AEC-Q100 qualification status, real distributor pricing, drop-in alternatives within the SAM HA1 family, and automotive-grade design notes not consolidated on the manufacturer datasheet cover page.

RFQ संपर्क
ATSAML10D14A-MF - 32MHz Cortex-M23 MCU 16KB Flash | Microchip
ATSAML10D14A-MF

ATSAML10D14A-MF - 32MHz Cortex-M23 MCU 16KB Flash | Microchip

The Microchip Technology ATSAML10D14A-MF is an ultra-low-power 32-bit ARM Cortex-M23 microcontroller from the SAM L10 family, featuring 16KB Flash and 4KB SRAM in a 24-pin VQFN (4x4 mm) package. It operates at up to 32 MHz, consumes less than 25 uA/MHz in active mode, and draws less than 100 nA in sleep mode, making it one of the industry's lowest-power Cortex-M23 MCUs. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (SRAM), and integrated peripherals. Within the broader taxonomy, the ATSAML10D14A-MF sits in the ultra-low-power MCU category, which targets battery-operated and energy-harvesting applications. ARM Cortex-M23 cores specifically use the Armv8-M architecture with TrustZone-M security extensions (note: TrustZone is enabled on the SAM L11 family, while the SAM L10 omits TrustZone for lower cost and power). The SAM L10/L11 families represent Microchip's lowest-power general-purpose 32-bit MCU platform. Key features include an enhanced Peripheral Touch Controller (PTC) supporting hardware-based capacitive touch sensing, advanced analog peripherals (12-bit ADC, 10-bit DAC, operational amplifiers, and analog comparators), SERCOM serial communication interfaces, and an ISO7816 smart card interface. The 24-VQFN package offers a compact 4x4 mm footprint suitable for space-constrained PCB designs. Architecturally, the device uses a single-cycle hardware multiplier, MPU for memory protection, and Microchip's proprietary picoPower technology that enables deep-sleep retention modes with sub-microamp standby current. Security features include CRC, true random number generator, and secure boot (without TrustZone). Typical applications include IoT sensor nodes, wearable health monitors, smart home devices, battery-powered industrial sensors, secure access control (without TrustZone), and touch-based human-machine interfaces. The combination of low power, integrated touch, and analog peripherals makes it particularly suited for always-on edge devices. When designing with this part, ensure your PCB layout provides adequate thermal dissipation even though the device is low-power. Use the SERCOM modules (each reconfigurable for I2C/SPI/UART) to maximize pin utilization. Decoupling capacitors (100 nF + 1 uF) should be placed within 3 mm of the VDD pins. This page synthesizes distributor pricing, same-family variants, and practical design notes that complement the manufacturer datasheet for accelerated component selection.

RFQ संपर्क
ATSAML10D14A-MU - 32MHz Cortex-M23 MCU, 16KB Flash | Microchip
ATSAML10D14A-MU

ATSAML10D14A-MU - 32MHz Cortex-M23 MCU, 16KB Flash | Microchip

The Microchip Technology ATSAML10D14A-MU is an ultra-low-power 32-bit ARM Cortex-M23 microcontroller from the SAM L10 family, featuring 16KB Flash, 4KB SRAM, and a 32MHz CPU in a 24-pin VQFN (4x4 mm) package. It is engineered for the lowest power consumption in any Cortex-M23 MCU, drawing less than 25 uA/MHz in active mode and under 100 nA in sleep mode. The device supports 1.62V to 3.63V supply operation and includes enhanced peripheral touch (PTC) controller, 12-bit ADC, comparators, and ISO7816 smart card interface for security-sensitive applications. A microcontroller (MCU) is an integrated circuit containing a processor core, program memory, data RAM, and programmable peripherals on a single chip. The ATSAML10D14A-MU belongs to the Cortex-M23 family, the smallest and most energy-efficient implementation of the Armv8-M architecture with TrustZone-ready extensions. In the broader hierarchy it sits within low-power MCUs -> 32-bit microcontrollers -> embedded processors -> semiconductors, designed specifically for battery-powered edge devices and IoT endpoints where nanoamp quiescent current matters. Key features include 16KB Flash with ECC, 4KB SRAM, 12-channel 12-bit 1 MSPS ADC, two analog comparators with window mode, a 32kHz RTC, multiple low-power sleep modes, and a flexible Event System for inter-peripheral signaling without CPU intervention. The integrated Peripheral Touch Controller (PTC) supports hardware-driven capacitive touch sensing with up to 256 channels. The device also features a 16-bit Sigma-Delta DAC and PTC-driven hardware wake-on-touch from deep-sleep. Architecturally, the SAM L10 uses a Cortex-M23 core with single-cycle I/O port access, NVIC with 4 priority levels, and Microchip's proprietary picoPower technology. The bus matrix connects Flash, SRAM, and AHB/APB peripherals through a tightly-coupled low-leakage memory subsystem, allowing sleep currents to drop to under 100 nA with full RAM retention and RTC running. Typical applications include wearable fitness bands, smart sensors, security tokens, smart card readers, IoT endpoints, capacitive touch human-machine interfaces (HMIs), battery-powered medical monitors, and home automation sensor nodes. The 24-VQFN package suits miniaturized PCB layouts common in coin-cell-powered products. When designing with this part, consider the mandatory 1.62V minimum supply for Flash operations and select the appropriate low-power mode to balance wake-up latency against current budget. The PTC peripheral requires careful PCB layout guidelines; refer to the Atmel/Microchip touch design package for sensor routing recommendations. This page consolidates distributor pricing, drop-in compatible SAM L10 family members, and PCB-level design notes not covered in the manufacturer datasheet to accelerate part selection and PCB bring-up.

RFQ संपर्क