माइक्रोकंट्रोलर्स

उत्पाद (20,000+)

ATSAMS70J19A-AN - 300MHz Cortex-M7 MCU, 512KB Flash | Microchip
ATSAMS70J19A-AN

ATSAMS70J19A-AN - 300MHz Cortex-M7 MCU, 512KB Flash | Microchip

The Microchip Technology ATSAMS70J19A-AN is a 32-bit ARM Cortex-M7 microcontroller with Floating Point Unit (FPU), running at up to 300 MHz, featuring 512 KB of Flash and 256 KB of SRAM in a 64-pin LQFP (10x10 mm) package. As a member of the SAM S70 family, it integrates a rich peripheral set including high-speed USB, CAN-FD, Ethernet MAC, HSEM (Hardware Semaphore), and a TFT LCD controller. An ARM Cortex-M7 microcontroller is a high-performance 32-bit processor core built on the ARMv7-M architecture, featuring a 6-stage superscalar pipeline, branch prediction, single-precision/double-precision FPU, and tightly-coupled memory (TCM) for deterministic low-latency code execution. It belongs to the broader hierarchy: ARM Cortex-M7 -> ARM Cortex-M family -> 32-bit MCU -> embedded microcontroller -> semiconductor. The Cortex-M7 is purpose-built for DSP workloads and real-time control, replacing legacy DSP ICs in many applications. Key features of the ATSAMS70J19A-AN include 300 MHz core clock, 512 KB Flash, 256 KB SRAM, 16 KB ICache, 16 KB DCache, USB 2.0 High-Speed with integrated PHY, dual CAN-FD controllers, 10/100 Ethernet MAC with 1588 PTP support, 12-bit AFEC (analog front-end controller) up to 1 MSPS, and an image sensor interface (ISI). The SAM S70 family targets high-performance industrial, automotive infotainment, and IoT edge applications. The device uses a single-precision/double-precision FPU and DSP extensions, supporting floating-point and SIMD instructions for advanced signal processing. The Cortex-M7 core delivers 1500 CoreMarks and up to 300 DMIPS performance, enabling complex control loops, audio processing, and machine-learning inference at the edge. Typical applications include industrial motor control, building automation, smart energy meters, automotive infotainment, IoT gateways, point-of-sale terminals, and graphics-enabled HMI with TFT LCD. The Ethernet MAC and CAN-FD bus make it suitable for industrial networking, while the USB HS and image sensor interface enable multimedia endpoints. When designing with this device, ensure the regulator is sized to handle the worst-case inrush during ADC reference stabilization and PLL lock. The 64-pin LQFP footprint is shared with SAM E70, SAM V70, and SAM V71 family members, easing migration when scaling Flash/RAM or adding CAN-FD/HS USB requirements. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
ATSAMS70N19A-AN - SAM S70 Cortex-M7 MCU 300MHz 512KB Flash | Microchip
ATSAMS70N19A-AN

ATSAMS70N19A-AN - SAM S70 Cortex-M7 MCU 300MHz 512KB Flash | Microchip

The Microchip Technology ATSAMS70N19A-AN is a 32-bit ARM Cortex-M7 microcontroller with Floating Point Unit (FPU) running up to 300 MHz, integrating 512 KB of Flash and 256 KB of SRAM, housed in a 100-pin LQFP (14x14 mm) package. This SAM S70 family device targets high-performance embedded designs requiring deterministic real-time control, rich connectivity, and a rich peripheral mix including Ethernet, HS USB, CAN-FD, and a 12-bit ADC with up to 24 channels. What is a Cortex-M7 microcontroller? A Cortex-M7 is a 32-bit ARM processor core designed for high-performance microcontroller applications, including a hardware single-precision and double-precision FPU, tightly coupled memories (TCM), and an instruction cache. It sits above Cortex-M4 in the ARM hierarchy (Cortex-M0/M0+ -> Cortex-M3 -> Cortex-M4 -> Cortex-M7 -> Cortex-M33/M55/M85), offering superscalar DSP and SIMD capabilities for signal-processing and motor-control workloads. The Cortex-M7 belongs to the broader family of microcontrollers -> microcontrollers ICs -> embedded processors -> semiconductors. Key features include 300 MHz core clock, 512 KB Flash program store, 256 KB SRAM, a 12-bit 1 Msps ADC, two CAN-FD controllers, 10/100 Mbps Ethernet MAC, high-speed USB host/device with PHY, an image sensor interface, an external bus interface (EBI) for SRAM/NOR/NAND, and a high-speed SD/MMC host. The 100-LQFP package exposes most peripherals for low-cost PCB designs while supporting industrial temperature operation from -40C to +105C. Technically, the SAM S70 architecture couples an MPU-aware Cortex-M7 core to a multi-layer AHB bus matrix with separate peripherals and tightly-coupled memories, enabling deterministic DMA and zero-wait-state Flash access via a 2 KB cache. 256 KB SRAM is split between system SRAM and backup SRAM retained in certain low-power modes; the 12-bit ADC and analog comparators are routed to dedicated peripheral channels. Hardware crypto is not part of the SAM S70 itself - that feature lives on the related SAME70 family. Typical applications include industrial motor control (BLDC/PMSM), industrial automation and PLC interfaces, building automation and HVAC, smart energy metering, automotive body/infotainment peripherals, audio processing front ends, machine vision at the edge, and connected gateways with Ethernet and CAN-FD. The SAMS70N19 is also used in medical instrumentation where the FPU and DSP extension accelerate filter computations. When designing with this device, allocate sufficient decoupling (100 nF near each VDD/VDDIO pin plus bulk) and follow Microchip's SAMS70 errata for HS USB PHY, EBI timing, and CAN-FD revision items. Use MPLAB X IDE with MPLAB Harmony 3 (csp, core, and a supported middleware layer) for code generation, peripheral drivers, and FreeRTOS integration. This page synthesizes distributor pricing, parametric positioning, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone - including a cross-vendor comparison row and a curated set of Microchip SAME70/SAMS70 family pin-compatible options for reuse of existing PCB layouts.

RFQ संपर्क
ATSAMS70Q20A-AN - 300MHz Cortex-M7 MCU, 1MB Flash | Microchip
ATSAMS70Q20A-AN

ATSAMS70Q20A-AN - 300MHz Cortex-M7 MCU, 1MB Flash | Microchip

The Microchip ATSAMS70Q20A-AN is a 32-bit ARM Cortex-M7 microcontroller with Floating Point Unit (FPU), running up to 300 MHz, featuring 1 MB of Flash and 384 KB of SRAM in a 144-pin LQFP package. This SAM S70 family device delivers 1500 CoreMark / 600 DMIPS performance and integrates rich connectivity including HS USB, Ethernet, CAN-FD, and a TFT LCD controller, making it suitable for high-performance embedded graphics and audio applications. What is a Cortex-M7 microcontroller? A Cortex-M7 MCU is a 32-bit RISC processor from ARM designed for deterministic real-time control with DSP extensions and a hardware single-precision/double-precision FPU. It sits in the hierarchy ARM Cortex-M -> 32-bit MCU -> microcontroller -> embedded processor, and is typically chosen when developers need sub-200ns interrupt latency, SIMD DSP, and large code/RAM footprints for graphical or audio signal chains. Key features include 16 KB of ICache and 16 KB of DCache, a Multi-Port SRAM architecture, two 12-bit AFEC ADCs up to 1.5 Msps, USB 2.0 High-Speed with on-chip PHY, 10/100 Ethernet MAC with 1588 PTP support, a 2D graphics LCD TFT controller with overlay, a hardware cryptographic accelerator (AES, TRNG), and 8/16-bit external bus interface (EBI) for SDRAM/NAND/NOR expansion. The device also embeds a Floating Point Unit that natively executes single- and double-precision IEEE 754 operations. The ATSAMS70Q20A-AN employs a Harvard-bus implementation with a tightly-coupled TCM block, deterministic 4-cycle interrupt entry, and a system controller that handles clock, reset, and brown-out supervision. Its peripheral set includes CAN-FD, four I2S ports for audio codec interfacing, an image sensor interface (ISI), a camera interface, and up to 119 GPIOs. Engineering trade-offs include higher dynamic power at 300 MHz than Cortex-M4 parts and a 144-LQFP footprint that requires careful power-plane design. Typical applications span industrial motor control, industrial HMI / TFT panels, point-of-sale terminals, audio amplification systems, automotive infotainment prototyping, building-automation gateways, and IoT edge nodes that demand on-the-fly TLS handshake acceleration via the integrated crypto engine. The wide 3.0V to 3.6V supply and 1.7V to 3.6V IO tolerance also let it co-exist with 1.8V sensors. When designing with this MCU, place four 0.1 µF + 1 µF decoupling pairs near the VDDIO/VDDCORE pin groups, route the 12 MHz crystal traces symmetrically, and use a 4-layer backup across IC pin groups to keep the high-speed USB and Ethernet impedance at 90 Ω differential. Provide a 32.768 kHz low-power crystal on the XIN32/XOUT32 pads if RTC wake-from-backup is required. This page synthesizes distributor pricing, drop-in alternatives sourced from Microchip cross-reference data, and practical design notes not consolidated in the manufacturer datasheet.

RFQ संपर्क
ATSAMS70Q21B-AN - 300MHz Cortex-M7 MCU 2MB Flash | Microchip
ATSAMS70Q21B-AN

ATSAMS70Q21B-AN - 300MHz Cortex-M7 MCU 2MB Flash | Microchip

The Microchip ATSAMS70Q21B-AN is a 32-bit ARM Cortex-M7 microcontroller from the SAM S70 family, featuring a 300 MHz CPU core with Floating Point Unit (FPU), 2 MB of Flash program memory, and 384 KB of SRAM, packaged in a 144-pin LQFP (20x20 mm). It operates from a 1.08V to 1.32V core supply and is qualified for industrial temperature ranges of -40C to +105C, making it suitable for demanding embedded applications. An ARM Cortex-M7 microcontroller is a high-performance 32-bit RISC processor designed for deterministic real-time control and signal processing. The M7 architecture includes a double-precision FPU, SIMD instructions, and tightly coupled memory, sitting above Cortex-M4 and below Cortex-A application processors in the ARM embedded hierarchy. Within Microchip's SAM family, the S70 series targets high-performance motor control, industrial automation, and audio/graphics applications where the M7's DSP extensions deliver substantial throughput advantages over M4 designs. Key features of the ATSAMS70Q21B-AN include 114 programmable I/O lines, a 16-bit external bus interface with 24-bit address bus, multiple PWM channels for motor and power control, a high-speed ADC, multiple DMA channels for low-overhead data movement, and a DAC for analog output generation. The peripheral set also includes USB, CAN, Ethernet MAC, and high-speed serial interfaces, supporting connected industrial designs. The device integrates a 6-layer bus matrix with separate bridges for I/O and peripheral DMA, enabling parallel data movement without CPU intervention. The M7 core's branch prediction, instruction cache, and tightly coupled RAM deliver sustained 300 MHz performance with single-cycle SRAM access, enabling real-time DSP workloads such as field-oriented motor control and audio processing at sample rates well above 100 kHz. Typical applications include industrial motor drives (FOC for BLDC/PMSM), factory automation controllers, building automation HMI panels, audio processing systems, and connected IoT edge nodes. The combination of large memory, rich peripherals, and industrial temperature range makes it a strong fit for systems previously served by mid-range DSPs or higher-end Cortex-M4 parts. When designing with this MCU, ensure the 144-LQFP PCB layout accommodates the 0.5 mm pitch footprint and provides adequate thermal copper for high-clock-current transients. Decoupling must follow the manufacturer's reference schematic with bulk, mid-frequency, and high-frequency ceramics placed close to each supply pin pair. This page synthesizes verified distributor pricing, drop-in alternatives drawn from the same SAM S70/SAM E70 family, and practical design notes that go beyond the manufacturer datasheet to support sourcing and engineering decisions.

RFQ संपर्क
ATSAMS70Q21B-ANT - 300MHz Cortex-M7 MCU 2MB Flash 144-LQFP | Microchip
ATSAMS70Q21B-ANT

ATSAMS70Q21B-ANT - 300MHz Cortex-M7 MCU 2MB Flash 144-LQFP | Microchip

The Microchip Technology ATSAMS70Q21B-ANT is a 32-bit ARM Cortex-M7 microcontroller with FPU operating at up to 300 MHz, integrating 2 MB of Flash and 384 KB of SRAM in a 144-pin LQFP (20x20 mm) package with 114 user I/O lines. It belongs to the SAM S70 family of high-performance flash microcontrollers designed for connected and industrial applications requiring Ethernet connectivity, high-speed connectivity, and rich peripherals. What is a Cortex-M7 microcontroller? A microcontroller (MCU) is a single-chip computer integrating a CPU core, memory (Flash + SRAM), and peripherals (GPIO, timers, ADC, communication interfaces). The ARM Cortex-M7 is a high-end 32-bit core featuring a superscalar pipeline, hardware single-precision and double-precision floating-point unit (FPU), DSP extensions, and tightly-coupled memory for deterministic real-time response. It sits above Cortex-M4 in the ARM hierarchy and below Cortex-A application processors, optimized for demanding signal processing and motor/control tasks. Key features of the ATSAMS70Q21B-ANT include: ARM Cortex-M7 core with FPU and DSP extensions, 300 MHz maximum CPU clock, 2 MB embedded Flash with ECC, 384 KB SRAM, 16-bit external bus interface with 24-bit address space, and a wide peripheral set including HS USB, CAN-FD, Ethernet MAC, SDMMC, image sensor interface, high-speed SPI/TWI, 12-bit ADC, DAC, PWM timers, and EMAC with 1588 PTP support. The device is built on an ultra-low-power process and supports 1.08 V to 1.32 V core supply, with operating temperature range of -40 C to +85 C (industrial grade). The integrated Ethernet MAC with IEEE 1588 PTP makes it well-suited for industrial Ethernet protocols (EtherCAT, PROFINET), while the Cortex-M7 vectored interrupt controller and tightly-coupled memories deliver deterministic latency under heavy I/O. Typical applications include industrial control with real-time Ethernet (EtherCAT slave, PROFINET IO), motor control (BLDC, PMSM, servo drives), graphical HMI with TFT LCD and image sensor interface, automotive body and gateway modules, IoT edge gateways, audio processing with hardware FPU, and SCADA / smart grid terminals. The 2 MB Flash supports over-the-air firmware update with dual-bank partitioning. When designing with this MCU, verify that the 144-LQFP (20x20 mm) footprint and pinout are compatible with your PCB layout. The -ANT suffix denotes tray packaging at the standard 144-LQFP body size, suitable for both prototype and high-volume assembly. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
ATSAMV70Q20B-CB - ARM Cortex-M7 300MHz MCU, 1MB Flash | Microchip
ATSAMV70Q20B-CB

ATSAMV70Q20B-CB - ARM Cortex-M7 300MHz MCU, 1MB Flash | Microchip

The Microchip Technology ATSAMV70Q20B-CB is an ARM Cortex-M7 microcontroller in the SAM V70 automotive family, featuring a single-core 32-bit processor with double-precision FPU running at up to 300 MHz, paired with 1 MB of Flash and 384 KB of SRAM in a 144-pin TFBGA (10x10 mm) package. It is qualified to the AEC-Q100 automotive reliability standard and integrates high-speed connectivity including Ethernet, CAN-FD, USB, and a 16-bit HSMCI SD-card interface. The device is targeted at automotive body, chassis, and gateway ECUs where deterministic real-time performance and a rich peripheral set are mandatory. An ARM Cortex-M7 MCU is a 32-bit microcontroller built on the ARMv7-M architecture with a deeply pipelined core that delivers 2.14 CoreMark/MHz performance, a hardware double-precision floating-point unit, single-precision and double-precision SIMD instructions, and tightly-coupled memory for low-latency code and data access. It sits within the broader taxonomy of MCU -> embedded microcontroller -> SoC -> semiconductor. The Cortex-M7 family supersedes Cortex-M4 by adding cache controllers, branch prediction, and dual-issue capability, making it the highest-performance mainstream Cortex-M part before moving into Cortex-M33/M55 secure islands. Key features include 1 MB (1M x 8) embedded Flash, 384 KB of multi-port SRAM, an MPU for memory protection, 16-bit SDRAM and 8/16-bit PSRAM external bus interface, an image sensor interface, an advanced 16-bit sigma-delta ADC with up to 24 channels, and a hardware crypto accelerator (TRNG, AES, SHA, RSA). The on-chip peripherals include 8-bit/16-bit image sensor interface (ISI), 12-bit DAC, 16-bit timers, PWM, I2S, I2C, SPI, UART/USART, and high-speed USB with integrated PHY. The 144-TFBGA package offers compact 10x10 mm footprint while exposing up to 88 GPIOs. The architectural depth of SAM V70 lies in its Cortex-M7 core, which integrates an L1 instruction cache and branch target address cache to mitigate Flash wait-state penalties at 300 MHz, while the multi-port SRAM bank allows parallel DMA, Ethernet, and code execution without bus contention. The peripheral event system (PDMA, AFEC) and an interrupt controller with configurable priorities allow deterministic sub-microsecond response on critical tasks such as motor control or CAN-FD message handling. An integrated flexible 8- to 16-bit external bus interface (EBI) simplifies expansion to SDRAM or QSPI Flash. Typical applications include automotive body controllers, HVAC panels, LED matrix drivers, industrial PLCs, motor-control front-ends, and IoT gateways that require Ethernet + CAN-FD co-existence. The device is also a strong fit for human-machine-interface (HMI) panels with TFT-LCD support, audio infotainment nodes, and CAN/LIN gateways. When designing with this part, designers should provision an external LDO or DC-DC for the 1.2V core rail and follow Microchip's Atmel Studio/Microchip Studio pin-mux configuration to avoid peripheral conflict on shared I/O lines. The part uses an automotive-grade process and is PPAP-capable.

RFQ संपर्क
ATSAMV71N20B-CBT - 300MHz Cortex-M7 MCU 1MB Flash | Microchip
ATSAMV71N20B-CBT

ATSAMV71N20B-CBT - 300MHz Cortex-M7 MCU 1MB Flash | Microchip

The Microchip ATSAMV71N20B-CBT is an automotive-grade 32-bit microcontroller based on the ARM Cortex-M7 core with double-precision FPU, running at up to 300MHz with 1MB (1M x 8) embedded Flash and 384KB SRAM, supplied in a 100-ball TFBGA (9x9 mm) package. Per Microchip, the SAM V71 family is manufactured under ISO-TS-16949 requirements and qualified to AEC-Q100 for automotive applications. A microcontroller (MCU) is a single-chip embedded processor that integrates a CPU core, memory, and peripherals into one device, forming the highest-volume class of embedded processing ICs used across automotive, industrial, and consumer systems. The SAM V71 sits at the high-performance end of the MCU hierarchy, positioned above general-purpose Cortex-M4 devices by its superscalar Cortex-M7 pipeline delivering 5.04 CoreMark/MHz. Key features include a 300MHz core with cache acceleration, dual 16-bit 2Msps ADCs, Ethernet MAC with AVB support for automotive audio-video bridging, dual CAN interfaces, I2S for digital audio, USB high-speed device/host, and multiple USART/SPI/TWI peripherals. The LCD controller-capable parallel capture interface and SDRAM/SDIO support enable graphics and data-logging designs. Architecturally, the Cortex-M7 core pairs a six-stage dual-issue pipeline with tightly-coupled memory (TCM) and configurable instruction/data caches, allowing deterministic execution for motor control and audio DSP workloads. The double-precision FPU accelerates control-loop math, while embedded Flash with ECC supports functional-safety-oriented designs. Typical applications include automotive gateway and body controllers, industrial automation and motor control, and Ethernet AVB audio/video networking. The combination of 300MHz throughput, hardware Ethernet, and dual CAN makes it a strong single-chip solution for connected embedded nodes. Design consideration: ensure a clean 3V to 3.6V supply with proper decoupling at all VDDIO/VDDCORE pins, and verify BGA escape-routing capability before committing to the 100-TFBGA footprint; pricing shown as of 2026-08-29.

RFQ संपर्क
ATSAMV71Q21B-AAB - 300MHz Cortex-M7 MCU 2MB Flash | Microchip
ATSAMV71Q21B-AAB

ATSAMV71Q21B-AAB - 300MHz Cortex-M7 MCU 2MB Flash | Microchip

The Microchip Technology ATSAMV71Q21B-AAB is a high-performance 32-bit ARM Cortex-M7 microcontroller with a double-precision FPU, running up to 300 MHz, integrating 2 MB of Flash and 384 KB of SRAM in a 144-pin LQFP (20x20 mm) package. It belongs to the SAM V71 automotive-grade family and features an extensive peripheral set including Ethernet, CAN-FD, high-speed USB, HS SDIO/QSPI, I2S, and a 12-bit ADC. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, RAM, and on-chip peripherals designed to embedded applications. Within the silicon taxonomy, the ATSAMV71Q21B-AAB sits in the hierarchy: Cortex-M7 core -> ARM 32-bit MCU -> microcontroller -> embedded IC -> semiconductor. The Cortex-M7 architecture is a superscalar pipeline with branch prediction, tightly coupled memory (TCM), and an instruction/data cache that delivers deterministic real-time performance alongside DSP-class signal processing throughput. Key features include a 16-bit external bus interface (EBI) for SDRAM expansion, a graphics LCD controller for TFT panels, hardware cryptographic acceleration (AES, TRNG), and a 12-bit 2 Msps ADC. The device supports 1.8V, 2.5V, and 3.3V I/O operation and is qualified to AEC-Q100 for automotive applications, making it suitable for body electronics, infotainment HMI, and industrial motor control. The Cortex-M7 core integrates DSP extensions (SIMD) and an FPU that handles single- and double-precision IEEE-754 operations. Combined with 16 KB I-cache + 16 KB D-cache and up to 384 KB system SRAM, it sustains the throughput needed for motor-control loops, audio processing, and predictive-maintenance algorithms on factory-floor equipment. Typical applications include automotive body and chassis ECUs, industrial PLC and HMI controllers, motor-control inverters, audio and infotainment head units, and industrial IoT gateways. The integrated Ethernet MAC and HS USB simplify connectivity for industrial and automotive networking stacks. When designing with this device, plan decoupling with bulk 4.7 uF + 100 nF per VDD pin pair and provide a 25 MHz external crystal with proper PCB guard routing. The AEC-Q100 grade adds cost only for the qualification itself - the silicon, footprint, and firmware are identical to industrial equivalents, enabling a single PCB design to serve both end markets. This page synthesizes distributor pricing, drop-in alternatives within the SAM V71 family, and practical hardware-design notes not consolidated in the manufacturer datasheet.

RFQ संपर्क
ATSAMV71Q21B-AABT - 300MHz ARM Cortex-M7 MCU, 2MB Flash | Microchip
ATSAMV71Q21B-AABT

ATSAMV71Q21B-AABT - 300MHz ARM Cortex-M7 MCU, 2MB Flash | Microchip

The Microchip ATSAMV71Q21B-AABT is a high-performance 32-bit ARM Cortex-M7 microcontroller with FPU, operating at up to 300 MHz and featuring 2 MB of Flash memory and 384 KB of SRAM in a 144-pin LQFP package (20x20 mm). It is a member of the SAM V71 family targeting automotive and industrial applications with rich connectivity including CAN-FD, Ethernet, USB, and high-speed serial interfaces. The part suffix "B" denotes the silicon revision, "AAB" specifies the 144-LQFP package and automotive grade, and "T" indicates tape-and-reel packaging. A Cortex-M7 microcontroller is a 32-bit RISC processor core designed for high-performance embedded applications with deterministic real-time behavior. The Cortex-M7 includes a double-precision floating-point unit (FPU), DSP extensions, and a tightly-coupled memory subsystem that delivers single-cycle access to Flash and SRAM. Within Microchip's portfolio, the SAM V71 family sits between the Cortex-M4-based SAM E70/S70 family and higher-end Cortex-M7 parts, sharing the SAME70/SAMS70 peripheral set while adding higher core frequency and larger memory configurations for graphics, audio, and motor-control applications. Key features include 300 MHz core clock, 2 MB Flash, 384 KB SRAM, dual CAN-FD controllers, 10/100 Mbps Ethernet MAC with IEEE 1588 support, USB 2.0 High-Speed with PHY, three CAN-FD interfaces, four UART/USART, three I2C, three SPI/I2S, an integrated TFT LCD controller with 2D graphics accelerator (GFX), 12-bit ADC up to 2 Msps, and a 32-bit timer/counter block. The device supports embedded trace (ETM) and is supported by MPLAB X IDE, MPLAB Harmony 3, and Atmel Studio. Architecturally, the ATSAMV71Q21B uses a Harvard-cache architecture with 16 KB I-cache and 16 KB D-cache, branch prediction, and a memory protection unit (MPU). The graphics accelerator (GLCDC) supports up to XGA (1024x768) panels and provides hardware alpha-blending, making it suitable for HMI applications. The dual CAN-FD controllers comply with ISO 11898-1:2015 and support up to 8 Mbps data rates for next-generation automotive networks. Typical applications include automotive body and chassis ECUs, industrial HMI panels, machine-vision edge nodes, audio processing systems, motor-control drives with field-oriented control (FOC), and graphics-rich IoT gateways. The automotive-grade temperature range (-40C to +105C) and AEC-Q100 qualification make the device suitable for safety-critical in-cabin systems. When designing with this MCU, ensure your linker scripts and startup files match the silicon revision (B). The SAM V71 family shares peripherals with SAM E70/S70, allowing firmware migration with minimal changes. For graphics applications, configure the GLCDC for the target display timing and use the 2D accelerator (GFX) to offload GUI rendering from the CPU. This page synthesizes distributor pricing, AEC-Q100 qualified drop-in alternatives (including SAM E70 variants and SAMS70 variants), and design notes not found in the manufacturer datasheet, helping engineers rapidly select and source the right part for their application.

RFQ संपर्क
ATTINY12-8PU - 8-Bit 1KB Flash AVR MCU, 8MHz | Microchip
ATTINY12-8PU

ATTINY12-8PU - 8-Bit 1KB Flash AVR MCU, 8MHz | Microchip

The Microchip Technology ATTINY12-8PU is an 8-bit AVR RISC microcontroller with 1KB of Flash program memory, 64 bytes of EEPROM, 6 I/O ports, and an 8MHz maximum clock speed, supplied in an 8-pin PDIP package for 4V to 5.5V operation. It is designed for compact embedded control tasks where a small flash footprint, simple 8-pin footprint, and low component count are more important than extensive peripheral integration. An 8-bit AVR microcontroller is a reduced-complexity processor within the broader semiconductor and embedded-controller hierarchy. The ATTINY12 combines an AVR RISC core, Flash program memory, EEPROM data memory, general-purpose I/O, and an internal oscillator in one device. Its PDIP package also provides through-hole compatibility for prototyping, educational assemblies, and repair applications where a surface-mount package would be inconvenient. The ATTINY12-8PU provides 1KB of Flash memory organized as 512 x 16, 64 bytes of EEPROM, and 6 I/O ports. Its listed operating voltage range is 4V to 5.5V, with a maximum operating frequency of 8MHz. The device uses the AVR RISC architecture and is described as offering 90 powerful instructions with most instructions executing in a single clock cycle. Typical use cases include small sensor nodes, simple timers, LED indicators, basic control loops, teaching examples, and dedicated appliance controllers. Because the device has only 1KB of Flash and 64 bytes of EEPROM, it is best suited to compact firmware with limited buffering, calibration storage, and peripheral integration. It should not be selected when the design requires extensive code space, high-resolution ADC conversion, or a large number of I/O pins. The most important design consideration is supply-voltage margin. Operating from a nominal 5V rail requires the rail to remain within the stated 4V to 5.5V range, including transient and regulator tolerance. Designers should also account for the limited memory before adding libraries, and should confirm the exact pin function and startup behavior against the manufacturer datasheet when replacing a different DIP-8 device. This page combines distributor availability, verified device parameters, same-package replacement guidance, and application-specific design notes. It is intended to help engineers identify whether the ATTINY12-8PU is suitable for a new design or whether a higher-memory ATtiny family member should be selected instead.

RFQ संपर्क
ATTINY12-8SI - 8-Bit AVR, 8MHz, 1KB Flash | Microchip Technology
ATTINY12-8SI

ATTINY12-8SI - 8-Bit AVR, 8MHz, 1KB Flash | Microchip Technology

Microchip Technology ATTINY12-8SI is an 8-bit AVR ATtiny microcontroller operating at 8MHz, with 1KB of Flash program memory organized as 512 x 16 words and 64 bytes of EEPROM data memory. The device is offered in an 8-pin SOIC package and is identified as an industrial-temperature variant. A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, data memory, and digital input/output circuitry on one device. The ATTINY12-8SI belongs to the ATtiny family, within the broader AVR microcontroller and embedded-controller hierarchy. Its small memory capacity and limited pin count make it suitable for compact control tasks rather than general-purpose applications requiring extensive code storage or peripheral connectivity. The principal characteristics include an 8-bit AVR core, 8MHz clock rating, 1KB Flash memory, 64 bytes of EEPROM, and an 8-SOIC package. These parameters support small embedded routines such as state sequencing, simple signal generation, switching control, and basic logic coordination. The 512-word Flash organization provides 1KB of code storage, while the EEPROM provides a small amount of nonvolatile data storage separate from program memory. The ATtiny12 architecture places significant emphasis on compact implementation. With only eight pins, external signal allocation requires careful pin planning, and the available GPIO resources are limited compared with larger ATtiny devices. Program development must therefore remain compact, and peripheral functions must be selected around the actual pin requirements of the target circuit. The 8MHz maximum clock supports faster execution than lower-speed microcontrollers while retaining a straightforward embedded-control architecture. Typical uses include small industrial control modules, LED sequencing and lighting controllers, compact timers, simple sensor interfaces, and auxiliary control functions in larger equipment. It is most appropriate where the firmware can fit within 1KB and only a small number of external signals is required. Designs needing serial communication, larger data storage, more I/O, or substantially more program memory should use a higher-capacity microcontroller instead. For PCB implementation, place the decoupling capacitor close to the VCC pin and route the ground connection with minimal resistance. Confirm every use of the reset-capable and ADC-capable pins against the manufacturer pin-description table, especially when the package footprint is shared with another ATtiny family member. The industrial-temperature ordering code must also be confirmed against the system’s environmental requirements before release to production. This product page combines the manufacturer identity, core operating parameters, memory configuration, package information, application guidance, and qualified drop-in alternatives into one engineering reference. It also highlights the limits of the ATTINY12-8SI so purchasing teams can distinguish genuine pin-compatible replacements from larger microcontrollers that share the SOIC-8 format but require different firmware, pin assignments, or peripheral resources.

RFQ संपर्क
ATTINY13A-MU - 20MHz 8-Bit AVR MCU | Microchip
ATTINY13A-MU

ATTINY13A-MU - 20MHz 8-Bit AVR MCU | Microchip

Microchip Technology ATTINY13A-MU is a low-power 8-bit AVR microcontroller rated for operation from 1.8 V to 5.5 V, with a maximum clock frequency of 20 MHz and up to 20 MIPS throughput. The device contains 1 KB of in-system-programmable Flash, 64 bytes of EEPROM, 64 bytes of SRAM, a 32-byte register file, and a four-channel 10-bit ADC. It is packaged as a 20-QFN-EP in a 4 mm by 4 mm footprint. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, peripherals, and input/output pins into one device. The ATtiny13A belongs to the TinyAVR family, which is part of Microchip's 8-bit AVR portfolio and is commonly used for compact control tasks. Its enhanced RISC architecture executes many instructions in one clock cycle, allowing performance approaching 1 MIPS per MHz while helping designers balance processing throughput against power consumption. The principal features of the ATTINY13A-MU include 20 MHz operation, 1 KB of Flash memory, 64 bytes of EEPROM, 64 bytes of SRAM, and a four-channel 10-bit analog-to-digital converter. The picoPower architecture is designed for low-power embedded systems. Peripherals identified for the ATtiny13A family include brown-out detection and reset, power-on reset, PWM, and a watchdog timer, while the product page also identifies In-System Programming support. The AVR enhanced RISC core provides an 8-bit processing platform with up to 20 MIPS throughput at 20 MHz. The 1 KB Flash capacity accommodates compact firmware, while the 64-byte EEPROM supports nonvolatile parameter storage and the 64-byte SRAM handles working data. The ADC provides four 10-bit channels for measurements from sensors, switches, resistive dividers, and simple analog interfaces. Operating voltage is stated as 1.8 V to 5.5 V, allowing integration with both low-voltage and conventional 5 V systems. Typical uses include compact LED controllers, simple sensor interfaces, button-driven controls, battery-operated accessories, hobby projects, and small embedded automation nodes. The four ADC channels are particularly useful when a design must monitor several analog quantities without adding a separate converter. ISP programming makes the device suitable for small production runs and prototype boards because firmware can be loaded through the programming interface after assembly. Designers should account for the limited 1 KB Flash and 64-byte SRAM when selecting a programming toolchain and organizing firmware. The I/O budget and analog channel requirements must also be checked against the exact 20-QFN-EP pin arrangement. Use the manufacturer pin-description table and package drawing during PCB layout, and confirm all operating conditions against the device's specified voltage and frequency limits. This product analysis combines the manufacturer specifications with practical guidance for firmware sizing, programming, analog measurement, and compact PCB design. It also distinguishes the ATTINY13A-MU from package variants and larger ATtiny devices whose memory, speed, or pin count changes the replacement decision.

RFQ संपर्क
ATTINY13A-PU - 20MHz 8-Bit AVR MCU | Microchip
ATTINY13A-PU

ATTINY13A-PU - 20MHz 8-Bit AVR MCU | Microchip

The Microchip ATTINY13A-PU is an 8-bit AVR microcontroller with a 20 MHz maximum clock, 1 KB of in-system programmable flash, and an 8-PDIP package. It operates from 1.8 V to 5.5 V and provides 64 bytes of EEPROM, 64 bytes of SRAM, a 32-byte register file, and a four-channel 10-bit ADC. The ATTINY13A-PU combines these resources in an 8-pin through-hole package for compact embedded control. An 8-bit microcontroller is a programmable semiconductor that executes instructions from embedded flash memory and uses registers, SRAM, and peripherals to control a system. The ATtiny13A belongs to the TinyAVR family within the AVR architecture and provides a practical balance of processing speed, memory, analog measurement, and low power operation for cost-sensitive embedded products. Its small pin count makes it especially useful where board area and simplicity are important. Core resources include 1 KB of flash, 64 bytes of SRAM, 64 bytes of EEPROM, and a 32-byte register file. The four-channel 10-bit ADC supports analog sensing, while the AVR enhanced RISC architecture executes instructions in a single clock cycle. At 20 MHz, the processor can approach 20 MIPS of instruction throughput under suitable operating conditions. In-system programming supports programming and reprogramming through the ICSP interface. The device is based on a low-power CMOS process and uses the AVR enhanced RISC architecture. The picoPower implementation is intended to improve power efficiency relative to the original ATtiny13 while retaining a familiar programming model and peripheral arrangement. A limited 1 KB flash capacity favors compact control routines, pin-change interrupts, timers, communication state machines, and other tasks that do not require a large application framework. Typical uses include LED lighting controls, small motor or actuator controllers, simple keypads, compact sensor interfaces, teaching boards, and low-cost embedded products. The four ADC channels make the device useful for reading resistive or analog sensors, while its GPIO pins can operate digital inputs and outputs. The 8-PDIP format also simplifies breadboard prototyping, hand assembly, repair, and educational experiments. Designers should allocate the small SRAM carefully and avoid duplicating library functions that consume substantial flash. Place the decoupling capacitor close to VCC, use the reset and programming pins according to the manufacturer data sheet, and verify ADC input limits against the selected operating voltage. When timing, brown-out detection, or power-consumption behavior is important, review the device-specific electrical characteristics before production release. This product record combines the manufacturer data sheet, programming resources, package information, and application-oriented guidance. It also identifies the clearest same-package drop-in alternative and explains the hardware and software checks that should accompany any replacement decision.

RFQ संपर्क
ATTINY13A-SF - 20MHz 1KB AVR MCU | Microchip Technology
ATTINY13A-SF

ATTINY13A-SF - 20MHz 1KB AVR MCU | Microchip Technology

Microchip Technology ATTINY13A-SF is a picoPower 8-bit AVR RISC-based microcontroller with 1 KB of ISP Flash, 64 bytes of EEPROM, 64 bytes of SRAM, and a 4-channel 10-bit ADC, operating up to 20 MHz in an 8-pin SOIC package. It supports 1.8 V to 5.5 V operation and delivers up to 20 MIPS throughput at 20 MHz. The ATTINY13A-SF is designed for compact embedded systems where low cost, low power, and deterministic control are more important than memory capacity. A microcontroller is a programmable control component that combines a CPU core, nonvolatile program memory, working memory, and peripherals on one integrated circuit. The ATtiny13A belongs to the TinyAVR family and uses the AVR enhanced RISC architecture. Its instruction set executes most instructions in a single clock cycle, allowing clock speed to be balanced against power consumption in battery-operated equipment. The ATTINY13A-SF includes 90 powerful AVR instructions, eight general-purpose working registers, brown-out detection, power-on reset, a watchdog timer, and four 10-bit ADC channels. Its small memory footprint suits simple state machines, sensor interfaces, LED control, timers, and compact consumer accessories. The 20 MHz maximum clock provides additional timing margin for protocol handling and control loops. The ATtiny13A is based on low-power CMOS technology and is designed for both active and low-power operation. The manufacturer describes the picoPower architecture as a way to optimize power consumption while maintaining execution throughput. The 1.8 V to 5.5 V operating range permits operation from single-cell and low-voltage systems as well as conventional 3.3 V or 5 V rails. Typical applications include battery-powered sensors, simple LED and motor-control boards, compact remote controls, consumer appliances, hobby projects, and small embedded control modules. The ATTINY13A can be programmed through In-Circuit Serial Programming, while the MPLAB Snap debug interface supports in-circuit debugging through the device I/O and reset lines. When designing a board, verify the SOIC-8 footprint, pin 1 orientation, supply decoupling, programming access, and the voltage range of every connected peripheral. Use the manufacturer datasheet for the complete pin description, electrical characteristics, fuse settings, and recommended application circuits.

RFQ संपर्क
ATTINY13A-SH - 8-Bit 20MHz AVR Microcontroller | Microchip
ATTINY13A-SH

ATTINY13A-SH - 8-Bit 20MHz AVR Microcontroller | Microchip

Microchip Technology ATTINY13A-SH is an 8-bit AVR tinyAVR microcontroller with a 20 MHz maximum clock, 1 KB in-system programmable Flash, 64 bytes EEPROM, and 64 bytes SRAM in an 8-pin SOIC package. The device provides 6 I/O ports and operates from low-voltage supplies identified in the verified data as 2.5 V, 3.3 V, and 5 V. According to the Microchip manufacturer datasheet, its enhanced RISC architecture executes powerful instructions in a single clock cycle, delivering throughput approaching 1 MIPS per MHz. An 8-bit microcontroller is a compact embedded-processing semiconductor that integrates a CPU core, program memory, data memory, I/O, and peripherals on one chip. The ATtiny13A belongs to the TinyAVR family and uses the AVR enhanced RISC architecture. Within the product hierarchy, it is an 8-bit RISC microcontroller, an embedded controller, and a semiconductor designed for cost-sensitive control tasks that require modest memory, limited I/O, and low power consumption. The primary features include 1 KB of Flash program memory, 64 bytes of EEPROM, 64 bytes of SRAM, 20 MHz operation, six I/O ports, and an AVR instruction set with 90 powerful instructions. The manufacturer describes most instructions as completing in a single clock cycle. These characteristics make the ATTINY13A-SH suitable for compact embedded controllers, simple timers, basic logic sequencers, small motor-control functions, and low-pin-count sensing systems where a larger MCU would add unnecessary cost and board area. Technically, the ATTINY13A combines a one-cycle-per-instruction AVR core with limited but deterministic resources. Its 1 KB Flash supports compact firmware, while the 64-byte SRAM and 64-byte EEPROM provide working and nonvolatile data storage. The device is offered in a surface-mount 8-SOIC package, allowing automated assembly and compact PCB placement. The verified distributor data identifies the device as active and lists it as an 8-bit AVR microcontroller with a 20 MHz clock. Typical applications include small appliance controls, sensor interfaces, LED-sequencing modules, compact motor controllers, battery-operated products, and simple industrial automation nodes. For these applications, the decisive benefits are the six available I/O ports, 1 KB program-memory capacity, low-voltage operation, and compact SOIC-8 footprint. A design requiring substantially more code space, RAM, peripheral capability, or pins should use a larger ATtiny or ATmega-class controller instead. A critical design consideration is to verify the complete operating-voltage envelope, clock configuration, reset behavior, and programming interface against the manufacturer datasheet before PCB release. Decoupling capacitors should be placed close to the supply pin, and unused inputs should be brought to a defined logic level. ISP programming should be exposed when firmware updates or production programming are required, rather than relying on an inaccessible programming interface. This page combines the verified manufacturer specifications, distributor availability, package details, sourcing information, and practical selection guidance with a strict analysis of same-footprint drop-in alternatives. It also distinguishes genuine drop-in options from unavailable or unverifiable replacements so engineers can evaluate migration risk before modifying a PCB.

RFQ संपर्क
ATTINY13A-SSU - 8-Bit AVR MCU, 1KB Flash, 20MHz | Microchip
ATTINY13A-SSU

ATTINY13A-SSU - 8-Bit AVR MCU, 1KB Flash, 20MHz | Microchip

The Microchip Technology ATTINY13A-SSU is an 8-bit AVR RISC-based microcontroller featuring 1 KB of in-system programmable Flash, 64 bytes of EEPROM, 64 bytes of SRAM, a 32-byte register file, and a 4-channel 10-bit A/D converter, housed in an 8-pin SOIC (SO-8) package. The device operates across a 1.8 V to 5.5 V supply range and achieves up to 20 MIPS throughput at a 20 MHz clock, letting designers trade power consumption for processing speed on the fly. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile memory (Flash/ROM), volatile working memory (SRAM), and a configurable set of peripherals such as timers, ADCs, and digital I/O onto one IC. MCUs form the lowest tier of embedded computing, sitting beneath microprocessors (MPUs) and application processors in capability but above fixed-function logic ICs in flexibility. The AVR family places a RISC-style load/store CPU core next to tightly-coupled peripherals, and the tinyAVR sub-family scales this architecture into the smallest 8-pin parts for cost- and space-sensitive designs. Key features include hardware multipliers-free single-cycle execution, a debugWIRE on-chip debug interface, an analog comparator, a programmable watchdog timer with separate on-chip oscillator, and two PWM-capable 8-bit timers plus one high-speed timer. The picoPower technology extends battery life through multiple sleep modes that drop active current to the microamp range. Six general-purpose I/O lines are available on the SO-8 footprint, with PB5 serving as the reset pin and supporting in-circuit serial programming. Architecturally, the ATTINY13A-SSU fuses an enhanced RISC core (90+ instructions, most single-cycle) with a Harvard-style memory layout that lets the CPU fetch instructions from Flash while data accesses hit SRAM in the same cycle. The peripheral set is selected for analog and digital mixed-signal chores: a 10-bit successive-approximation ADC with four input channels, a programmable analog comparator, and dedicated timer/counter blocks with PWM output match units for switching tasks. Typical applications include LED drivers, battery chargers, small motor controls, remote control transmitters, simple sensor nodes, and wearable accessories where board area and quiescent current are constrained. The wide 1.8 V to 5.5 V range lets a single design migrate between single-cell lithium and 3.3 V or 5 V system rails without hardware changes. When laying out a board, place the decoupling capacitor (typically 100 nF) within a few millimetres of the VCC pin and route a low-impedance GND pour under the exposed copper area to keep digital switching noise out of the ADC inputs. Ensure the RESET pin (PB5) is pulled high through 10 kohm and accessible to the ISP header so in-circuit programming and debugWIRE debug sessions can be performed without removing the part. This page consolidates distributor pricing, drop-in alternatives, and engineering design notes that complement the manufacturer datasheet to accelerate part selection and PCB bring-up.

RFQ संपर्क
ATTINY13A-SU - 20MHz 8-Bit AVR Microcontroller | Microchip
ATTINY13A-SU

ATTINY13A-SU - 20MHz 8-Bit AVR Microcontroller | Microchip

The Microchip Technology ATTINY13A-SU is a low-power 8-bit AVR microcontroller with a 20 MHz maximum clock, 1 KB of in-system programmable Flash memory, 64 bytes of EEPROM, 64 bytes of SRAM, and a 4-channel 10-bit ADC, packaged in an 8-pin SOIC. It operates from 1.8 V to 5.5 V and can execute up to 20 MIPS at 20 MHz. An 8-bit microcontroller is a compact embedded-processing IC that combines a processor core, nonvolatile program memory, data memory, and peripherals on one die. The ATTINY13A belongs to the TinyAVR family within Microchip's AVR portfolio. Its enhanced RISC architecture executes many instructions in a single clock cycle, supporting processing throughput approaching 1 MIPS per MHz while allowing designs to balance speed against power consumption. The principal features of the ATTINY13A-SU include 1 KB of ISP Flash, 64 bytes of EEPROM, 64 bytes of SRAM, a 32-byte register file, and four 10-bit analog-to-digital converter channels. Its operating range of 1.8 V to 5.5 V supports low-voltage battery-powered equipment as well as conventional 5 V systems. In-system programming and ICSP interfaces support programming and debugging without removing the microcontroller from its circuit. The device uses the AVR enhanced RISC architecture and can reach 20 MIPS throughput at a 20 MHz clock. This processing rate is more than adequate for compact control tasks involving digital I/O, timing, simple control logic, and analog signal measurement. The ATtiny13A-SU combines this processing capability with a small memory footprint, making it suitable for cost- and power-sensitive embedded products rather than connectivity-heavy or high-memory applications. Typical uses include small motor controllers, temperature-sensor interfaces, battery monitors, LED controllers, appliance controls, hobby electronics, and simple sensor nodes. The four-channel 10-bit ADC is particularly useful when a design needs several analog inputs but does not require the memory, processing, or peripheral resources of a larger microcontroller family. For new layouts, preserve the ATtiny13A pin assignments and provide a decoupling capacitor close to VCC. Confirm the selected clock source, brown-out configuration, programming connector, and ADC reference arrangement against the manufacturer datasheet. Changes to package suffix, clock specification, or operating mode can alter qualification, programming, or temperature requirements even when the basic function remains the same. This product page consolidates the ATTINY13A-SU electrical characteristics, package information, pin assignments, lifecycle information, verified drop-in references, and practical design guidance. It supports engineers comparing the 8-pin SOIC implementation with documented alternatives without confusing electrical compatibility, package compatibility, and broader functional similarity.

RFQ संपर्क
ATTINY1624-SSU - 8-Bit AVR tinyAVR 2 MCU 20MHz 16KB Flash SOIC-14 | Microchip
ATTINY1624-SSU

ATTINY1624-SSU - 8-Bit AVR tinyAVR 2 MCU 20MHz 16KB Flash SOIC-14 | Microchip

The Microchip Technology ATTINY1624-SSU is an 8-bit AVR RISC microcontroller from the tinyAVR 2 family, featuring a hardware multiplier, 20 MHz maximum CPU clock, 16 KB in-system programmable Flash, 2 KB SRAM and 256 bytes of EEPROM, all housed in a 14-pin narrow-body SOIC package rated for industrial temperature (-40C to +85C). The device integrates the modern AVR CPU core with Core Independent Peripherals (CIPs) including event system, configurable custom logic, and 12-bit differential ADC with Programmable Gain Amplifier, enabling mixed-signal designs without external components. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, optimized for low-cost, low-power deterministic embedded control. Within the broader taxonomy, the ATTINY1624 sits under: microcontroller -> 8-bit MCU -> AVR family -> tinyAVR 2 series -> small-package (<=14-pin) variants. It is typically used as the system master in cost-sensitive products where 32-bit processing power is unnecessary but analog and timing peripherals are still required. Key differentiating specifications include: 16 KB Flash organized as 4K x 16-bit words (AVR instructions are 16/32-bit wide), true 1.8V-5.5V single-supply operation, up to 12 MIPS throughput at 20 MHz from internal oscillator, 12-bit differential ADC with up to 16-bit oversampling, and configurable custom logic blocks. The integrated event system allows peripherals to communicate without CPU intervention, reducing active time and average power. Sleep current below 1 uA in Power-Down with RTC running enables long battery life. The ATTINY1624 uses a modified Harvard architecture with a two-stage pipelined 8-bit AVR core. Flash is read in 16-bit words so 16 KB of Flash stores 8K instructions. The peripheral set includes USART, SPI, I2C (TWI), 12-bit ADC, 8-bit DAC reference, analog comparators, timers/counters and PWM channels. The 14-pin SOIC package exposes 12 GPIO with multiplexed peripheral functions. Typical applications include consumer white goods, battery-powered sensor nodes, IoT end-node controllers, LED lighting drivers, simple user interfaces (buttons/cap touch via QTouch), and small appliance control boards. The combination of small footprint, low power, and integrated analog makes it well suited for replacements of legacy ATtiny84/44 designs requiring more memory. When designing with this device, note that the -SSU suffix indicates SOIC-14 industrial-temperature grade; firmware is uploaded via UPDI (one-wire programming/debug) instead of the older ISP/PDI interface used on classic AVRs, so a UPDI programmer or debugger such as MPLAB Snap, PICkit 5, or Atmel-ICE is required. The QTouch library and Atmel START / MPLAB X IDE are supported for peripheral configuration and code generation. This page synthesizes current distributor pricing, drop-in alternatives in the same SOIC-14 footprint, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
ATTINY1626-XU - 20MHz 16KB AVR tinyAVR 2 MCU | Microchip
ATTINY1626-XU

ATTINY1626-XU - 20MHz 16KB AVR tinyAVR 2 MCU | Microchip

The Microchip Technology ATTINY1626-XU is an 8-bit AVR RISC microcontroller from the tinyAVR 2 family, delivering up to 20 MHz CPU performance with a hardware multiplier, 16 KB of Flash program memory, 2 KB of SRAM, and 256 bytes of EEPROM in a 20-pin SSOP industrial-grade package rated for -40C to +85C operation. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory, and peripherals around an 8-bit data bus. The tinyAVR 2 family sits within Microchip's broader AVR hierarchy (megaAVR / tinyAVR / XMEGA), and the ATtiny1626 belongs to the tinyAVR 2 sub-family designed for compact, low-power, event-driven embedded applications where modest Flash and small pin counts are sufficient. The ATTINY1626-XU suffix encodes the 20-pin SSOP package (X) and industrial temperature grade (U, matte tin lead-free finish). Key features include dual USART, I2C (TWI), and SPI interfaces for serial connectivity; an Event System for inter-peripheral signaling without CPU intervention; advanced digital peripherals such as CCL (Configurable Custom Logic) and ADC with PGA; and flexible low-power sleep modes. The 16 KB Flash allows mid-sized firmware loads, while 2 KB SRAM supports reasonable local data buffering. Operating voltage ranges from 1.8V to 5.5V, enabling direct connection to coin-cell, Li-ion, or 3.3V/5V rails without level translation. Architecturally, the AVR CPU uses a single-cycle RISC instruction set with a 3-stage pipeline delivering roughly 1 MIPS per MHz. The hardware multiplier accelerates integer math, and the Event System routes peripheral triggers directly between blocks, freeing the core for application code. Brown-out detection, watchdog timer, and the 20 MHz internal oscillator reduce external component count. Typical applications include compact IoT sensor nodes, low-power wireless control front-ends, consumer appliance keypads, battery-powered HVAC and smart-home devices, and industrial sensor-conditioning hubs where a 20-pin footprint, 5V tolerance, and modest memory suffice. When designing with this part, evaluate whether 16 KB Flash and 2 KB SRAM are sufficient; if more headroom is needed, the ATtiny1627 (same family, 24-pin) or ATtiny3226 (next-generation, 32 KB Flash) may be more appropriate. Always confirm pinout against the SSOP-20 land pattern before PCB layout. This page synthesizes distributor pricing from DigiKey and Mouser, same-family drop-in alternatives in the SSOP-20 footprint, and practical design notes not consolidated in the manufacturer datasheet.

RFQ संपर्क
ATTINY167-AXD - 8-bit AVR MCU, 16KB Flash, 20MHz, TSSOP-20 | Microchip
ATTINY167-AXD

ATTINY167-AXD - 8-bit AVR MCU, 16KB Flash, 20MHz, TSSOP-20 | Microchip

The Microchip (formerly Atmel) ATTINY167-AXD is an 8-bit AVR RISC-based microcontroller featuring 16KB In-System Programmable Flash, 512B EEPROM, and 512B SRAM, clocked up to 20 MHz, housed in a 20-pin TSSOP package. The device integrates a hardware LIN/UART controller, full-speed USB 2.0 device interface, 16 general-purpose I/O lines, 32 working registers, and a 10-bit ADC, delivering automotive-grade connectivity for embedded LIN nodes and USB peripherals. An 8-bit microcontroller (MCU) is a compact processor that integrates a CPU core, non-volatile program memory, volatile data memory, and peripheral interfaces on a single silicon die. The AVR family uses a modified Harvard architecture with single-cycle instruction execution, making 8-bit MCUs well suited for deterministic, low-power, real-time control tasks. Within the broader semiconductor taxonomy, MCUs belong to the embedded processor category, with 8-bit parts occupying the low-power, cost-sensitive end versus 16-bit and 32-bit MCUs that target higher computational throughput. The ATTINY167-AXD specifically adds automotive bus (LIN) and USB connectivity, a combination rarely found in 8-bit parts, while remaining in a small TSSOP-20 footprint. Key features include 16KB flash (8K x 16 words), 512B EEPROM for non-volatile data, 512B SRAM, hardware LIN 2.0 controller, USB 2.0 full-speed device, 10-bit ADC with up to 11 channels, 8-bit and 16-bit timers with PWM, an enhanced universal serial interface (USI), and a programmable watchdog timer with separate on-chip oscillator. The MCU operates from 1.8V to 5.5V across -40C to +125C (automotive grade), and supports in-system programming via SPI or USB, enabling field firmware upgrades without desoldering. The device uses Microchip's enhanced AVR RISC core executing instructions in a single clock cycle, achieving up to 20 MIPS throughput at 20 MHz. Hardware LIN handling offloads bit timing and checksum generation from the CPU, freeing cycles for application logic. The integrated USB transceiver and dedicated 3.3V regulator simplify USB device designs by eliminating external PHY or LDO components. The TSSOP-20 package balances IO count with a 6.5mm x 4.4mm board footprint, smaller than the SOIC-20 alternative. Typical applications include automotive LIN slave nodes (body controllers, seat modules, mirror controllers, sensor clusters), USB human-interface devices (HID mice, keyboards, custom peripherals), industrial sensor transmitters, and low-cost consumer devices requiring automotive temperature tolerance. The wide operating voltage and temperature range also make it suitable for harsh-environment IoT edge nodes. When designing with this device, prioritize decoupling: place a 100nF ceramic capacitor on each VCC pin within 2mm of the pad, and add a 10uF bulk capacitor near the USB VBUS line. For LIN applications, route the LIN line as a differential pair with the bus pull-up, and add TVS protection such as the NUP2105L. Always configure the fuses for the intended clock source (internal 8 MHz RC vs external crystal) before USB enumeration. This page synthesizes distributor pricing, drop-in compatible alternatives within the TSSOP-20 footprint, and practical automotive design notes not collected on a single manufacturer datasheet page.

RFQ संपर्क
ATTINY167-MU - 16MHz AVR MCU with 16KB Flash | Microchip
ATTINY167-MU

ATTINY167-MU - 16MHz AVR MCU with 16KB Flash | Microchip

The Microchip Technology ATTINY167-MU is an 8-bit AVR RISC-based microcontroller operating at 16 MHz with 16 KB of ISP Flash, 512 bytes of EEPROM, and 512 bytes of SRAM in a 32-pin VQFN 5x5 mm package. The device provides 16 general-purpose I/O lines and combines a compact embedded-control footprint with 16 KB of program memory for firmware, configuration data, and application logic. An 8-bit microcontroller is a compact digital controller built around a processor, nonvolatile program memory, data memory, and configurable input/output peripherals. The ATtiny family belongs to the TinyAVR segment of the AVR product hierarchy. These devices are commonly used where a control system needs deterministic embedded processing but does not require the memory, operating speed, or peripheral complexity of a high-end application processor. The ATTINY167-MU provides 16 KB of ISP Flash, 512 bytes of EEPROM, and 512 bytes of SRAM for persistent configuration and working data. Its 16 general-purpose I/O lines support digital sensing and control, while its 32 general-purpose working registers support efficient execution of the AVR instruction set. The microcontroller also includes an 8-bit timer/counter with compare modes and an 8-bit high-speed timer/counter for periodic and timing-related functions. Its AVR RISC architecture executes most instructions within a single clock cycle, which provides predictable behavior for motor, control, and interface tasks. The 16 MHz operating speed gives designers additional timing headroom over slower 8-bit implementations. The 32-pin VQFN package also includes an exposed pad according to the verified product listings, improving available heat-spreading area on the PCB when the device operates at elevated ambient temperatures or sustained computational load. Typical applications include compact industrial controllers, sensor-conditioning systems, actuator controllers, LED sequencing, low-cost instrumentation, and embedded control modules. The 16 I/O lines make the part useful for products that need several digital inputs and outputs while retaining a small 5x5 mm footprint. Its 16 KB Flash capacity is also appropriate for moderate control firmware that must be programmed in-system through the AVR ISP interface. The primary design consideration is matching firmware requirements to only 512 bytes of SRAM and 16 KB of Flash. Avoid interrupt handlers or library structures that require excessive stack space, and verify bootloader, application, and in-system programming requirements before final firmware allocation. PCB layouts must also follow the manufacturer's exposed-pad and thermal-land guidance rather than treating the VQFN as a conventional leaded package. This page combines verified manufacturer and distributor specifications with package details, application guidance, engineering considerations, and a transparent assessment of drop-in replacement availability. That information helps buyers evaluate the ATTINY167-MU beyond basic catalog parameters while clearly identifying specifications and equivalent parts that could not be verified from the supplied sources.

RFQ संपर्क
ATTINY167-SU - 16MHz 16KB 8-Bit AVR MCU | Microchip
ATTINY167-SU

ATTINY167-SU - 16MHz 16KB 8-Bit AVR MCU | Microchip

Microchip Technology ATTINY167-SU is an 8-bit AVR RISC microcontroller with a 16 MHz clock, 16 KB of in-system programmable Flash memory, 512 bytes of EEPROM, 512 bytes of SRAM, and 16 general-purpose I/O lines in a 20-pin SOIC package. The device combines compact code storage with serial communications and embedded control peripherals for cost-sensitive embedded systems. An 8-bit AVR microcontroller is a compact semiconductor in the microcontroller hierarchy, combining a CPU core, program memory, data memory, I/O ports, timers, and communication peripherals on one integrated circuit. The AVR enhanced RISC architecture is designed for efficient control tasks, while in-system programming allows firmware to be written or updated without removing the device from its target circuit. The ATTINY167-SU provides 16 KB of Flash for firmware, 512 bytes of EEPROM for nonvolatile parameters, and 512 bytes of SRAM for working variables. Its 16 general-purpose I/O lines support digital inputs, outputs, and multiplexed peripheral functions. A 16 MHz operating clock supports deterministic control in compact embedded products, and the 20-pin SOIC package simplifies assembly on conventional through-hole PCB layouts. The device is based on the low-power CMOS AVR enhanced RISC architecture and integrates an 8-bit timer/counter with compare modes. Serial interfaces support communication with sensors, transceivers, actuators, and service connectors. Because Flash, EEPROM, SRAM, I/O, timing, and communications share one package, the ATTINY167-SU can reduce board area and component count compared with discrete control solutions. Typical uses include LIN-connected automotive accessory modules, compact sensor interfaces, building-control nodes, lighting-control modules, and small industrial automation products. The combination of 16 KB Flash and a LIN controller is particularly useful in distributed networks where each node requires local firmware, nonvolatile configuration storage, and reliable low-speed communication. When designing the PCB, assign every pin through the manufacturer pin-description table and reserve programming-test access for ISP programming and debugging. Follow the recommended input, output, and decoupling capacitor arrangement, and verify external clock requirements before selecting oscillator components. Because 512 bytes of SRAM is modest, use efficient buffers and avoid unnecessarily large in-memory data structures. This product page combines the manufacturer specifications, package information, practical application guidance, and clearly qualified replacement analysis. The comparison and design notes focus on engineering differences that affect firmware compatibility, memory requirements, communications, layout, and production sourcing rather than simply repeating a catalog summary.

RFQ संपर्क
ATTINY167-XU - 16MHz 16KB AVR Microcontroller | Microchip
ATTINY167-XU

ATTINY167-XU - 16MHz 16KB AVR Microcontroller | Microchip

The Microchip Technology ATTINY167-XU is an 8-bit AVR RISC-based microcontroller with 16 KB of ISP Flash memory, 512 bytes of EEPROM, 512 bytes of SRAM, and up to 16 general-purpose I/O lines. It operates at up to 16 MHz and is offered in a 20-pin TSSOP package for compact embedded-control designs. An AVR microcontroller is a low-power programmable controller built around the AVR RISC instruction set. Its place in the product hierarchy is microcontroller > embedded controller > semiconductor, while the ATTINY167 belongs to the ATtiny family of small 8-bit RISC microcontrollers. These devices combine digital control, timers, serial interfaces, and analog functions in one integrated package, allowing compact products to replace combinations of discrete logic and analog components. Key features include 16 KB of ISP Flash program memory, 512 bytes of EEPROM, 512 bytes of SRAM, 32 general-purpose working registers, and an 8-bit timer/counter with compare modes. The device also provides a high-speed timer/counter, supporting applications that require precise timing, periodic events, input capture, or waveform generation. Its 16 general-purpose I/O lines provide flexible connections for switches, sensors, indicators, actuators, and communication peripherals. The ATTINY167 combines a high-performance 8-bit RISC core with on-chip nonvolatile storage and a compact peripheral set. ISP programming supports in-system firmware updates when the circuit provides the required programming access. The 512-byte SRAM is suitable for small control loops, state machines, communication buffers, and mixed analog-digital logic, while the 512-byte EEPROM preserves calibration values, configuration settings, counters, or product data when power is removed. Typical applications include compact industrial controllers, low-power sensor nodes, building and appliance controls, LED drivers, compact power-conversion controllers, and small motor-control systems. It is especially useful where an 8-bit architecture, deterministic peripheral timing, and space-efficient TSSOP packaging are more valuable than the processing power of a 32-bit MCU. PCB implementation should preserve access to the programming interface and provide the decoupling and clock arrangement specified by the manufacturer datasheet. Confirm ADC, timer, and communication pin assignments before fixing the board layout because peripheral functions can share I/O pins. For battery-powered equipment, calculate the average current from active-mode and power-sleep behavior rather than relying only on the maximum clock frequency. This page combines the ATTINY167-XU electrical characteristics, drop-in replacement guidance, application analysis, and design notes to support faster component selection and PCB implementation.

RFQ संपर्क
ATTINY20-CCU - 8-bit AVR MCU, 2KB Flash, 15-UFBGA | Microchip
ATTINY20-CCU

ATTINY20-CCU - 8-bit AVR MCU, 2KB Flash, 15-UFBGA | Microchip

The Microchip Technology ATTINY20-CCU is an 8-bit AVR RISC microcontroller with 2 KB of in-system programmable Flash memory, 128 bytes of SRAM, and 12 general-purpose I/O lines. It operates at up to 12 MHz and is packaged in a 15-UFBGA 3x3 mm package for space-constrained embedded designs. An 8-bit AVR microcontroller is a compact RISC-based controller that executes most instructions within a single clock cycle. The ATTINY20 belongs to the TinyAVR family, combining low-power operation with timer, counter, ADC, and PWM resources in a small package. Its architecture follows the MCU hierarchy from application-specific controller to embedded processor, RISC microcontroller, and integrated circuit. The device provides 2 KB of ISP Flash for program storage and 128 bytes of SRAM for working memory. Its 12 I/O lines support digital control and multiplexing functions, while the 16 general-purpose working registers support efficient register-based execution. Peripheral resources include an 8-bit timer/counter with two PWM channels, a 16-bit timer, and a 2-channel 10-bit ADC, according to the Microchip ATtiny20 product page. The ATtiny20 uses the compact AVR enhanced RISC architecture and can approach 1 MIPS per MHz under suitable instruction conditions. ISP programming permits firmware updates without removing the device from a finished assembly, which simplifies production programming, in-system upgrades, and low-volume manufacturing. Its 15-UFBGA package reduces board area compared with leaded or larger-surface-mount packages, although board layout and prototyping require fine-pitch assembly capability. Typical uses include compact sensor controllers, LED lighting modules, battery-powered monitoring devices, simple motor or fan controls, and embedded keypad interfaces. The two PWM channels can drive indicators or small mechanical loads, the ADC supports analog sensing, and the GPIO count is suitable for modest control loops where a larger MCU would be unnecessary. Designers should confirm the exact pin mapping and exposed-pad requirements against the manufacturer datasheet before layout because no compatible package SVG was available for verification. Firmware must also fit within 2 KB, and applications must account for the limited 128-byte SRAM. The 3x3 mm land pattern is mechanically compact but requires careful reflow control and inspection. This page consolidates the verified ATtiny20 family specifications, distributor inventory and pricing, sourcing links, and design considerations that are not presented together on a manufacturer datasheet summary. It also documents the limited availability of verified pin-for-pin replacements for this unusually small 15-UFBGA configuration.

RFQ संपर्क