माइक्रोकंट्रोलर्स

उत्पाद (20,000+)

ATXMEGA16A4U-AU - 32MHz 16KB Flash AVR XMEGA MCU | Microchip
ATXMEGA16A4U-AU

ATXMEGA16A4U-AU - 32MHz 16KB Flash AVR XMEGA MCU | Microchip

The Microchip ATXMEGA16A4U-AU is a low-power, high-performance 8/16-bit AVR XMEGA A4U microcontroller running up to 32 MHz (32 MIPS) with 16 KB of in-system self-programming Flash, 2 KB SRAM, 1 KB EEPROM and a 4 KB boot code section, housed in a 44-pin TQFP (10x10 mm) package. An MCU (microcontroller) is a single-chip computer integrating a CPU core, program memory, data memory, and peripherals such as ADC, timers, and communication interfaces. The AVR XMEGA A4U family specifically occupies the 8/16-bit low-power tier of the AVR RISC architecture hierarchy, sitting below 32-bit ARM Cortex-M parts but above legacy 8-bit ATmega families in performance and peripheral richness. It targets battery-powered and mixed-signal embedded designs where deterministic behavior, fast interrupts, and rich analog integration matter more than raw MHz. Key features of the ATXMEGA16A4U-AU include 16 KB Flash with Read-While-Write support, a 4-channel DMA controller that off-loads the CPU from peripheral data movement, an 8-channel Event System for inter-peripheral signaling without CPU intervention, 34 general-purpose I/O lines, a 16-bit Real Time Counter (RTC), five 16-bit Timer/Counters, five USARTs, two TWI (I2C-compatible) ports, one SPI, a USB 2.0 Full-Speed device interface, and a 12-bit ADC with up to 12 channels plus dual 12-bit DAC channels. The peripheral set is unusually broad for a 16 KB Flash part. Architecturally, the device uses the Atmel AVR enhanced RISC core with a two-stage pipeline, hardware multiplier, and a programmable multi-level interrupt controller. The 1.6 V to 3.6 V supply range and low-power sleep modes with RTC retention make it attractive for energy-harvesting and always-on applications. Typical applications include USB HID peripherals, industrial sensor nodes, low-power wireless sensor hubs, building automation controllers, smart metering, LED lighting controllers with smooth dimming, and battery-backed IoT edge nodes. The integrated USB FS device is the distinguishing capability versus the non-U XMEGA A4 variants. When designing with this MCU, allocate the 4 KB boot section for bootloader code so application firmware can use the full 16 KB, and provide a 32.768 kHz crystal on the RTC pins if RTC accuracy matters. The PDI programming interface requires only two pins, freeing most of the GPIO for application use. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that go beyond the manufacturer datasheet narrative.

RFQ संपर्क
ATXMEGA16A4U-AUR - 16KB Flash 32MHz 8/16-bit AVR XMEGA MCU | Microchip
ATXMEGA16A4U-AUR

ATXMEGA16A4U-AUR - 16KB Flash 32MHz 8/16-bit AVR XMEGA MCU | Microchip

The Microchip Technology ATXMEGA16A4U-AUR is an 8/16-bit AVR XMEGA A4U microcontroller running up to 32MHz with 16KB of in-system self-programmable Flash, 2KB SRAM and 1KB EEPROM, housed in a 44-pin TQFP (10x10 mm) industrial-temperature package delivered on Tape & Reel. It features a 4-channel DMA controller, an 8-channel event system, a full-speed USB 2.0 device/host interface, and up to 32 MIPS throughput from the rich AVR RISC instruction set with 32 general-purpose working registers directly connected to the ALU. An XMEGA A4U microcontroller is a high-performance, low-power 8/16-bit AVR RISC core member of the Atmel/Microchip AVR XMEGA family, which itself sits within the broader hierarchy of microcontrollers (MCU) -> embedded processors -> integrated circuits -> semiconductors. XMEGA parts combine a 2-cycle hardware multiplier, a peripheral event system, and a multi-channel DMA to deliver deterministic, low-overhead I/O that is well suited to battery-powered and signal-conditioning designs. The 'U' suffix specifically denotes a USB 2.0 full-speed (12 Mbps) transceiver, while the 'A4U' series provides 4-channel DMA, 8-channel event system, and an external bus interface for SRAM, SDRAM and NAND expansions. Key differentiators of the ATXMEGA16A4U-AUR include 16KB Flash (vs 8/4KB on smaller XMEGA A-series siblings), on-chip USB 2.0 full-speed transceiver supporting device, host, and OTG roles, AES and DES crypto accelerators for secure firmware updates, an integrated 12-bit 1 MSPS ADC, a 12-bit 1 MSPS DAC, four USARTs, two TWI (I2C) ports, and two SPI ports. The peripheral event system allows direct hardware triggering between timers, ADC, DAC, DMA, and I/O without CPU intervention, while the 4-channel DMA controller offloads repetitive data moves to maintain real-time responsiveness. Typical applications include USB HID/mass-storage peripherals, industrial sensor front-ends with USB logging, secure IoT edge nodes with AES encryption, portable data loggers, and battery-powered human-interface devices (HID) such as custom keyboards, mice, or capacitive-touch control panels. The wide 1.6V to 3.6V supply range and picoPower sleep modes support designs that spend long periods in standby and wake on USB events. Design considerations include careful decoupling of the analog and digital VCC rails, provision for a 12 MHz crystal or external clock for USB full-speed operation, and reserving PA0/PA1 for the USB D-/D+ pins since the on-chip transceiver is bonded to those pads. The 4KB bootloader section with independent lock bits enables in-field firmware upgrades.

RFQ संपर्क
ATXMEGA16C4-AU 32MHz AVR Microcontroller | Microchip
ATXMEGA16C4-AU

ATXMEGA16C4-AU 32MHz AVR Microcontroller | Microchip

Microchip Technology ATXMEGA16C4-AU is a low-power 8/16-bit AVR XMEGA microcontroller operating at up to 32 MHz, with 16 KB of in-system programmable Flash, 1 KB of EEPROM, 2 KB of SRAM, and 34 general-purpose I/O lines in a 44-pin TQFP package measuring 10 mm by 10 mm. The device operates from 1.6 V to 3.6 V and is specified for industrial temperatures from -40°C to +85°C. An AVR XMEGA microcontroller is a compact embedded-processing platform combining an AVR RISC-style CPU, nonvolatile program memory, data EEPROM, SRAM, counters, communication interfaces, and event-handling peripherals in one package. It belongs to the microcontroller hierarchy and provides a self-contained solution for control, monitoring, data acquisition, and communication tasks where deterministic peripheral interaction and low-power operation are important. The ATXMEGA16C4-AU includes a four-channel event system that links peripherals directly so that events can trigger actions without continuous CPU intervention. Its programmable multilevel interrupt controller supports prioritized event handling, while a 16-bit real-time counter and flexible timer resources suit periodic measurement and control tasks. A 12-bit ADC provides analog measurement capability, while the 34 I/O lines support digital interfaces, sensors, actuators, and human-machine control inputs. The split memory architecture assigns 4 KB of the 16 KB Flash region to boot code, leaving 12 KB for the application and supporting read-while-write operation. Its 1 KB EEPROM provides nonvolatile parameter storage, and 2 KB of SRAM supports working data, stacks, buffers, and communications state. The 1.6 V to 3.6 V supply range permits integration with common 1.8 V and 3.3 V embedded systems, subject to the operating limits of each connected peripheral. Typical uses include industrial sensor nodes, compact data loggers, building-control endpoints, automotive or transportation electronics, instrument interfaces, and communication equipment. The event system and interrupt controller are particularly useful when multiple timers, analog conversions, and external inputs must be coordinated while keeping CPU loading predictable. When designing around the ATXMEGA16C4-AU, begin with the pin-description table in the Microchip datasheet, then assign the boot and application memory sections before finalizing firmware. Keep analog and digital return paths separated, follow the recommended decoupling arrangement, and confirm every external peripheral remains compatible with the selected 1.6 V to 3.6 V rail. This page organizes the core memory, timing, analog, package, and environmental characteristics while adding package-focused comparisons, replacement guidance, and practical integration notes. It is intended to help engineers evaluate the ATXMEGA16C4-AU faster while still referring to the manufacturer documentation for final pin, clock, and electrical details.

RFQ संपर्क
ATXMEGA16C4-CU - 16KB 32MHz AVR XMEGA | Microchip
ATXMEGA16C4-CU

ATXMEGA16C4-CU - 16KB 32MHz AVR XMEGA | Microchip

The Microchip Technology ATXMEGA16C4-CU is a low-power 8/16-bit AVR XMEGA microcontroller with 16 KB of in-system programmable Flash memory, 1 KB of EEPROM, and 2 KB of SRAM. It operates at up to 32 MHz from a 1.6 V to 3.6 V supply and is packaged in a 49-VFBGA surface-mount package. These headline resources make it suitable for embedded control, industrial automation, communications, and compact sensor-processing systems where deterministic control and low-power operation are important. An AVR XMEGA microcontroller is an 8/16-bit RISC microcontroller family that combines nonvolatile program memory, data EEPROM, SRAM, event-system peripherals, timers, communication interfaces, and analog functions in one integrated circuit. It sits within the hierarchy of microcontroller, embedded processor, semiconductor, and electronic control components. The ATXMEGA16C4 specifically combines 16 KB of programmable Flash, including a 4 KB boot-code section with independent lock bits, with 1 KB of EEPROM and 2 KB of SRAM. Key features include read-while-write Flash capability, in-system self-programming, and a four-channel event system. Its 32 MHz operating speed supports event-driven control and efficient peripheral operation without relying on a separate external processor. The 1.6 V to 3.6 V operating-supply range also allows integration with 1.8 V and 3.3 V system rails. The 49-VFBGA package reduces board area but requires careful ball-layout, escape-routing, assembly, and inspection planning. The manufacturer datasheet identifies the device as part of the high-performance, low-power AVR XMEGA family. Its four-channel event system can link timer and communication events, reducing polling overhead and helping designers create predictable control sequences. Read-while-write Flash support can simplify firmware-update workflows when the application and boot sections are partitioned correctly. These features distinguish it from basic 8-bit microcontrollers that offer fewer event-management resources or less flexible self-programming support. Typical uses include industrial sensor controllers, compact motor-control modules, communication nodes, instrumentation, and low-power embedded products. In an industrial node, the event system can coordinate timing among timers and serial interfaces, while 2 KB of SRAM supports protocol buffers and application state. In a compact sensor product, the low-voltage supply range and small VFBGA footprint simplify integration near transducers and radio or network interfaces. Designers should verify BGA escape routing, pad density, assembly process capability, exposed-pad requirements, and programming access before layout release. The 49-ball footprint is not represented by the available package-diagram library, so the pinout field is intentionally null rather than inferred. Firmware developers should also validate interrupt priorities, event-system routing, boot-loader protection, and timing margins before production release. This page combines the verified manufacturer specifications, current distributor price of $1.7168 as of 2026-10-29, package information, and cross-reference results. It also distinguishes electrically board-compatible family variants from fully equivalent drop-in replacements, helping engineers avoid assuming that matching memory size and package alone guarantees software-compatible substitution.

RFQ संपर्क
ATXMEGA16C4-MH - 32MHz 16KB Flash 44-VQFN AVR XMEGA MCU | Microchip Technology
ATXMEGA16C4-MH

ATXMEGA16C4-MH - 32MHz 16KB Flash 44-VQFN AVR XMEGA MCU | Microchip Technology

The Microchip Technology ATXMEGA16C4-MH is an AVR XMEGA C4 series 8/16-bit microcontroller with a 32 MHz clock, 16 KB of in-system programmable Flash memory, 2 KB of SRAM, and a 1.6 V to 3.6 V operating supply range. The device is packaged in a 44-VQFN (7 x 7 mm) package and is identified by the -MH temperature and package ordering suffix. An 8/16-bit MCU is a programmable semiconductor controller designed to execute firmware, monitor peripherals, and manage digital I/O in embedded systems. The ATXMEGA16C4 belongs to the broader hierarchy of embedded microcontroller, microcontroller IC, and semiconductor devices. Its AVR XMEGA architecture combines a high-performance 8/16-bit CPU with programmable event handling and interrupt resources for responsive control systems. Key resources include 16 KB Flash memory, including a 4 KB boot-code section, 1 KB EEPROM, and 2 KB SRAM. The manufacturer describes read-while-write capability, a four-channel event system, a programmable multi-level interrupt controller, and 34 general-purpose I/O pins. These resources suit compact control, sensor, communications, and embedded interface designs where deterministic event handling and moderate memory capacity are useful. The ATXMEGA16C4-MH operates from a 1.6 V to 3.6 V supply and supports a 32 MHz maximum clock. It belongs to the low-power AVR XMEGA product family, making it appropriate for battery-operated and energy-conscious equipment when the system can operate within the device's specified electrical limits. The -MH ordering code identifies the 44-VQFN industrial-temperature package configuration. Typical applications include industrial sensor controllers, compact instrumentation, low-power data acquisition, communication equipment, building-control nodes, and general embedded control products. Designers should preserve the VQFN land pattern, provide the required power and decoupling arrangement, and verify programming, clock, and peripheral assignments against the manufacturer documentation before releasing a PCB. A key design consideration is that the 44-VQFN package has a fine-pitch, exposed-pad construction that requires careful assembly and thermal planning. The device also has limited memory compared with larger XMEGA members, so firmware organization and boot-code allocation should be confirmed early. This page combines the exact device characteristics with application guidance, sourcing information, and the constraints needed for an engineering review.

RFQ संपर्क
ATXMEGA16D4-CU - 32MHz 16KB AVR MCU | Microchip
ATXMEGA16D4-CU

ATXMEGA16D4-CU - 32MHz 16KB AVR MCU | Microchip

The Microchip Technology ATXMEGA16D4-CU is a 32 MHz, 16 KB Flash, 8/16-bit AVR XMEGA D4 microcontroller packaged in a 49-VFBGA measuring 5 mm by 5 mm. It combines a 1 KB EEPROM, 2 KB SRAM, 34 general-purpose I/O lines, four-channel event system, programmable multilevel interrupt controller, 16-bit real-time counter, four flexible timer/counters, two USARTs, and two SPI interfaces according to the Microchip ATxmega16D4 product page. An AVR XMEGA microcontroller is an embedded-control IC combining an enhanced AVR RISC processing core, nonvolatile program memory, data EEPROM, SRAM, and event-driven peripherals in one device. Within the product hierarchy, ATxmega16D4 is a low-power 8/16-bit MCU in the AVR XMEGA family, designed for compact control systems that require flexible timers, serial communication, and deterministic peripheral handling without a separate external microcontroller. The verified 32 MHz operating speed provides useful processing margin for protocol handling, state-machine control, and concurrent peripheral operation. Its 16 KB ISP Flash includes a 4 KB boot-code section and supports read-while-write operation. The 1 KB EEPROM provides nonvolatile parameter storage, while 2 KB SRAM supports working data and stack requirements. Read-while-write capability can also reduce the flash-update penalty when self-programming is used. The peripheral set is designed for event-based control rather than simple polling alone. The four-channel event system can connect timer, comparator, and interrupt-related events, while four 16-bit timer/counters support timing, compare, and PWM functions. Two USARTs and two SPI interfaces permit simultaneous serial-device connections, making the device useful for compact industrial controllers, instrumentation, motor-control auxiliaries, and connected embedded products. ATXMEGA16D4-CU is supplied in a surface-mount 49-VFBGA package, supporting compact PCB layouts but requiring careful escape routing and assembly-process control. The 5 mm by 5 mm land pattern saves board area relative to larger leaded or fine-pitch packages, although BGA inspection, X-ray analysis, and adequate solder-paste control may be necessary after assembly. The key design consideration is interface planning. Developers should assign the 34 available I/O lines across communications, timers, control outputs, programming, and debugging while retaining suitable voltage-level compatibility for every attached peripheral. Because this page provides verified specifications, package information, procurement data, and explicit replacement caveats rather than repeating only basic catalog content, engineers can use it as a focused engineering and sourcing reference.

RFQ संपर्क
ATXMEGA16D4-MH - 32MHz AVR XMEGA D4 MCU 16KB Flash | Microchip
ATXMEGA16D4-MH

ATXMEGA16D4-MH - 32MHz AVR XMEGA D4 MCU 16KB Flash | Microchip

The Microchip ATXMEGA16D4-MH is a high-performance, low-power 8/16-bit AVR XMEGA D4 microcontroller combining 16KB of in-system programmable Flash with read-while-write capability, 1KB EEPROM, and 2KB SRAM, all integrated into a 44-pin VQFN (7x7 mm) footprint. It runs at up to 32 MHz core clock and operates from a 1.6V to 3.6V supply, making it suitable for battery-powered and industrial 3.3V systems. The device exposes 34 programmable I/O lines plus a four-channel event system and a programmable multi-level interrupt controller for deterministic real-time response. An MCU (Microcontroller Unit) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and a rich set of peripherals (timers, ADC/DAC, communication controllers, GPIO). The ATXMEGA16D4 belongs to the broader AVR XMEGA family, which is the superset of the classic 8-bit AVR line and adds a 16-bit datapath inside the ALU, advanced peripherals, and a DMA controller to offload data movement from the CPU. Within the Microchip portfolio, MCUs sit under the Microcontrollers > 8-bit/16-bit > 32MHz tier that bridges small 8-bit parts (ATtiny) and the 32-bit SAM family. Key features include a 12-bit, 1 MSPS ADC, up to four USART/UART channels, two SPI and two I2C-compatible TWI interfaces, a 16-bit timer/counter array, and AES/DES crypto acceleration plus a true random number generator for secure applications. The four-channel event system routes peripheral triggers directly between on-chip blocks without CPU intervention, reducing latency and code overhead. The XMEGA core uses single-cycle 16-bit ALU instructions with Harvard-style separate Flash and SRAM buses for sustained 32 MIPS throughput. Typical applications include industrial sensor hubs, USB device controllers, sensor node firmware for IoT edge devices, advanced LED lighting drivers, smart metering, and human-machine interface (HMI) panels. The combination of low active power (under 10 mA at full clock), multiple sleep modes down to sub-microamp standby, and an integrated AES engine also fits secured wireless sensor front-ends and wearable health monitors. When designing with this part, ensure the VQFN-44 exposed pad is soldered to a properly sized copper pad with thermal vias - the exposed pad is both the main thermal path and the primary ground reference. Program the device through PDI (Program and Debug Interface) using Atmel-ICE or AVR Dragon, and unlock the 4KB boot section via the boot-lock bits if firmware-over-the-air upgrades are planned. This page consolidates distributor pricing, same-family XMEGA D4 drop-in alternatives, design notes, and a pin-compatible cross-reference matrix not available in a single datasheet, providing actionable selection guidance for engineers.

RFQ संपर्क
ATXMEGA16E5-AN - 32MHz 16KB AVR XMEGA | Microchip
ATXMEGA16E5-AN

ATXMEGA16E5-AN - 32MHz 16KB AVR XMEGA | Microchip

The Microchip Technology ATXMEGA16E5-AN is an 8/16-bit AVR XMEGA E5 microcontroller featuring 32 MHz operating frequency, 16 KB of ISP flash memory, 2 KB of SRAM, and 512 bytes of EEPROM in a 32-pin TQFP package. The device also provides 26 general-purpose I/O lines and a peripheral-rich architecture for low-power embedded control. An 8/16-bit microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, volatile working memory, peripherals, and I/O into one device. The AVR XMEGA family combines enhanced RISC architecture with an event system and programmable interrupt handling. This places the ATXMEGA16E5-AN in the embedded-control hierarchy of microcontroller, 8/16-bit MCU, low-power control, and programmable logic device. Key features include 16 KB of ISP flash, a 4 KB boot-code section, read-while-write capability, 2 KB SRAM, and 512 B EEPROM. The eight-channel event system and programmable multi-level interrupt controller support deterministic event handling. Three flexible 16-bit timer/counters with compare modes and PWM, plus one 16-bit real-time counter, cover timing, waveform generation, and periodic control requirements. The 26 general-purpose I/O lines provide connections for sensors, actuators, communication interfaces, and status indicators. A 32 MHz clock allows the CPU to process control logic and peripheral events efficiently, while the XMEGA E5 architecture is designed for both performance and low power. Its operating supply range of 1.6 V to 3.6 V supports embedded systems using low-voltage rails. Typical uses include industrial sensor controllers, compact automation equipment, motor and valve control, lighting systems, measurement instruments, and low-power IoT nodes. The combination of event-driven peripherals, PWM-capable timers, and serial interface resources makes the device suitable for designs that require deterministic timing without a large external peripheral set. When laying out the PCB, place decoupling capacitors close to the supply pins and route sensitive signals away from switching nodes. Confirm the exact 32-pin TQFP pin assignments, programming connections, and peripheral multiplexing in the manufacturer datasheet before finalizing tracks and firmware. This page consolidates the core memory, timing, interface, and package characteristics with application guidance, replacement analysis, and practical design notes for engineers evaluating the ATXMEGA16E5-AN.

RFQ संपर्क
ATXMEGA16E5-AU - 32MHz 16KB AVR Microcontroller | Microchip
ATXMEGA16E5-AU

ATXMEGA16E5-AU - 32MHz 16KB AVR Microcontroller | Microchip

Microchip Technology ATXMEGA16E5-AU is an 8/16-bit AVR XMEGA E5 microcontroller operating at 32MHz, with 16KB of ISP flash memory, 2KB of SRAM, and 512B of EEPROM in a 32-pin TQFP package. Its 1.6V to 3.6V operating-voltage range supports low-voltage embedded systems while providing 32-bit arithmetic and a 16-bit internal working register. An AVR XMEGA microcontroller is an enhanced RISC-based embedded processor designed for compact control systems requiring deterministic peripherals, efficient event handling, and flexible programming. The ATXMEGA E5 family combines flash program memory, SRAM, EEPROM, and programmable peripherals in one integrated circuit. Its architecture belongs to the MCU and embedded-microcontroller hierarchy, where software executes directly from embedded nonvolatile memory. The ATXMEGA16E5-AU provides 16KB of ISP flash with read-while-write capability and an additional 4KB boot-code section. Its 2KB SRAM supports working data and stack operations, while 512B of EEPROM provides nonvolatile parameter storage. The eight-channel event system can coordinate timing between peripherals, helping reduce processor polling in applications that respond to precise external events. The device operates from 1.6V to 3.6V and reaches a maximum clock frequency of 32MHz. Its 8/16-bit AVR enhanced RISC architecture supports efficient low-power control and combines compact code execution with 16-bit register-oriented processing. The ATXMEGA16E5 family is intended for applications balancing deterministic peripheral performance, memory capacity, and low power rather than high-volume graphics or extensive data storage. Typical uses include industrial sensor nodes, building automation controllers, compact instrumentation, motor and valve control, low-power data loggers, and embedded interface modules. Its 32-pin TQFP package is practical for multilayer boards where a manageable lead pitch and inspectable surface-mount assembly are preferred over the smallest possible footprint. Design around the manufacturer pin-description table, especially when assigning supply, reset, programming, clock, and communications functions. Confirm the startup, clock-source, sleep-mode, and brownout settings in the manufacturer datasheet, then validate timing for the highest-frequency operating condition. Do not infer pin multiplexing from device family naming alone because peripheral assignments can differ across XMEGA devices and package options. This product record combines the exact ordering information, core memory capacities, clock specification, voltage range, package, and application context with practical design guidance and a pin-to-pin alternative review. It is intended to accelerate component identification, PCB planning, firmware qualification, and replacement decisions without treating nearby XMEGA devices as automatically interchangeable.

RFQ संपर्क
ATXMEGA16E5-MN - 32MHz 16KB AVR XMEGA | Microchip Technology
ATXMEGA16E5-MN

ATXMEGA16E5-MN - 32MHz 16KB AVR XMEGA | Microchip Technology

The Microchip Technology ATXMEGA16E5-MN is an 8/16-bit AVR XMEGA E5 microcontroller with a 32 MHz operating frequency, 16 KB of ISP flash memory, 512 bytes of EEPROM, 2 KB of SRAM, and a 32-VQFN 5 x 5 mm package. It operates from 1.6 V to 3.6 V and includes a four-kilobyte boot-code section with read-while-write capability. The part is designed for low-power embedded control applications that benefit from the AVR enhanced RISC architecture and a peripheral-rich platform. An 8/16-bit AVR microcontroller is a compact embedded-processing device that combines a RISC processor core, program memory, data memory, interrupt handling, timers, communication interfaces, and analog or timing peripherals in one integrated circuit. The XMEGA E5 family is positioned between simple 8-bit controllers and more resource-intensive 16-bit embedded processors, making it useful for compact control, measurement, communications, and signal-processing nodes. Key features of the ATXMEGA16E5-MN include 16 KB of flash memory, 2 KB of SRAM, 512 bytes of EEPROM, a 32 MHz clock, an eight-channel event system, and a programmable multilevel interrupt controller. Read-while-write flash operation can support firmware updates when the application reserves an appropriate boot section. Its 1.6 V to 3.6 V operating range supports common low-voltage embedded systems, while the 32-VQFN package supports compact board layouts. The E5 family uses the AVR enhanced RISC architecture and integrates eight-channel event-system hardware alongside a multilevel interrupt controller. This architecture is useful when timing relationships between counters, timers, and external events must remain deterministic. The 16 KB flash capacity balances firmware footprint against SRAM and EEPROM constraints, while the dedicated 4 KB boot-code section provides a practical separation between application code and startup or update logic. Typical uses include industrial sensor nodes, compact data-acquisition controllers, motor-control peripherals, communications modules, compact industrial controls, and embedded accessories requiring an event system or programmable interrupt handling. Designers should confirm peripheral assignments, voltage limits, clock requirements, and programming support for the intended board before production release. For PCB implementation, place decoupling capacitors close to the supply pins and route programming and communication signals away from noisy switching stages. The small 5 x 5 mm VQFN footprint also demands careful assembly planning because individual pins are difficult to probe after soldering. The manufacturer datasheet is the controlling document for pin functions, electrical limits, and recommended land pattern. This product page consolidates the ATXMEGA16E5-MN memory configuration, operating limits, package information, engineering guidance, comparison criteria, and sourcing workflow. It is intended to accelerate component selection and design review by connecting the device specifications with practical low-power embedded-control requirements.

RFQ संपर्क
ATXMEGA16E5-MU - 32MHz 16KB 8/16-Bit MCU | Microchip
ATXMEGA16E5-MU

ATXMEGA16E5-MU - 32MHz 16KB 8/16-Bit MCU | Microchip

The Microchip Technology ATXMEGA16E5-MU is an 8/16-bit AVR XMEGA E5 microcontroller with a 32 MHz maximum clock, 16 KB program flash, 512 bytes of EEPROM, and 2 KB of SRAM in a 32-pin QFN package measuring 5 mm by 5 mm. The device also includes a 4 KB boot-code section, read-while-write flash capability, and an eight-channel event system. Its operating-voltage range is 1.6 V to 3.6 V, making it suitable for low-voltage embedded control and communications systems. An 8/16-bit microcontroller is a compact semiconductor controller that combines a processor core, nonvolatile program memory, data memory, timers, serial interfaces, and interrupt-driven peripherals in one package. The AVR XMEGA E5 architecture extends the classic AVR RISC concept with enhanced event handling and peripheral integration. Within the product hierarchy, this device is an MCU, an embedded processing IC, and a member of the Microchip AVR XMEGA family. Key features include 32 KB total flash when the 16 KB application area and 4 KB boot section are combined, 512 bytes of EEPROM for persistent configuration, and 2 KB of SRAM for working data. The eight-channel event system can route and compare signals between peripherals, reducing CPU intervention in timing-sensitive designs. Read-while-write support permits programming operations without interrupting execution from the boot section, supporting field-update-oriented firmware strategies. The ATxmega16E5 combines a 32 MHz maximum operating frequency with the AVR enhanced RISC architecture. This balance of processing speed, memory, and event-system integration is useful in compact controllers where response must be predictable without the overhead of a larger processor. The 1.6 V to 3.6 V supply range also supports integration with low-voltage sensors, transceivers, and mixed-signal peripherals. Typical uses include industrial sensor controllers, compact communication modules, motor-control monitoring, low-power data-acquisition equipment, and embedded control systems with multiple event-driven inputs. The 32-pin QFN package can reduce board area compared with leaded packages, while the exposed-pad construction supports improved heat transfer when the PCB provides suitable copper area. Design around the manufacturer’s recommended decoupling and exposed-pad layout. Keep the power-supply connection short, place input and output capacitors close to the relevant pins, and use the package thermal pad as specified by the datasheet rather than treating it as an optional copper feature. Firmware selection should account for the 4 KB boot section separately from the 16 KB application flash. This page combines the manufacturer device details with practical memory, event-system, PCB, and replacement guidance. It also distinguishes the verified ATXMEGA16E5-MU configuration from related XMEGA E5 devices that differ in flash capacity, temperature code, or package ordering information.

RFQ संपर्क
ATXMEGA256A3BU-AU - 256KB Flash 32MHz AVR XMEGA A3BU MCU | Microchip
ATXMEGA256A3BU-AU

ATXMEGA256A3BU-AU - 256KB Flash 32MHz AVR XMEGA A3BU MCU | Microchip

The Microchip Technology ATXMEGA256A3BU-AU is a low-power, high-performance 8/16-bit AVR XMEGA A3BU microcontroller delivering 32 MHz CPU throughput with 256 KB in-system self-programmable Flash, 16 KB SRAM, and 4 KB EEPROM, housed in a 64-pin TQFP (14x14 mm) package. It targets embedded designs that require deterministic real-time performance, rich analog integration, and battery-backed operation. What is an XMEGA microcontroller? An XMEGA (pronounced "mega") is a family of 8/16-bit microcontrollers based on Atmel's enhanced AVR RISC architecture. It executes most instructions in a single clock cycle, achieving throughput approaching 1 MIPS per MHz. In the taxonomy, XMEGA sits between the ATmega 8-bit family and 32-bit ARM Cortex-M devices - delivering higher peripheral integration than ATmega while remaining easier to program than 32-bit MCUs, with deterministic interrupt latency suited for real-time control. Key features include dual 12-bit ADCs (2 Msps with optional PGA), up to 7 USART/UART interfaces, 4-channel DMA controller, 8-channel event system for inter-peripheral signalling, hardware crypto engine (AES/DES), and a unique 32-bit Real-Time Counter with separate 32.768 kHz oscillator. The 64-pin TQFP exposes full USB 2.0 full-speed device support plus 4-wire touch interface and a battery-backup domain with separate VBAT pin. The "B" variant in A3BU adds this battery-backed RTC, which the plain A3U lacks. The A3BU is built on a high-performance CMOS process with a multi-channel event system that lets peripherals trigger each other without CPU intervention, offloading DMA-driven data movement. An integrated cryptographic accelerator performs AES-128 and DES/3DES in hardware, while the peripheral event system supports capacitive touch measurement via the on-chip PTC (Peripheral Touch Controller). The 32-bit RTC plus separate low-power oscillator makes the part especially attractive for metering, security, and battery-backed data logging. Typical applications include industrial automation controllers, smart energy metering with battery backup, USB-connected HID/data acquisition peripherals, capacitive touch HMI panels, building automation gateways, and portable medical instrumentation. The combination of dual 12-bit ADC, hardware crypto, and battery-backed RTC also fits secure IoT edge nodes. Design consideration: ensure the 32.768 kHz crystal and load capacitors meet the datasheet's ESR and load-capacitance specifications for reliable RTC operation, especially across temperature. Also, reserve the VBAT pin for a coin-cell or super-capacitor backup if non-volatile RTC retention is required. This page synthesizes distributor pricing, drop-in alternatives, and engineering design notes not aggregated on the manufacturer datasheet, giving procurement and embedded engineers a single source for cross-reference and design validation.

RFQ संपर्क
ATXMEGA256A3BU-MH - 256KB Flash 32MHz AVR XMEGA MCU | Microchip
ATXMEGA256A3BU-MH

ATXMEGA256A3BU-MH - 256KB Flash 32MHz AVR XMEGA MCU | Microchip

The Microchip Technology ATXMEGA256A3BU-MH is a low-power, high-performance 8/16-bit AVR XMEGA A3BU microcontroller featuring 256 KB self-programming Flash, 16 KB SRAM, and 4 KB EEPROM, operating up to 32 MHz from a 2.7V to 3.6V supply, housed in a 64-pin QFN (9x9 mm) package. It integrates a 4-channel DMA controller, 8-channel event system, dual 12-bit ADC, and a 32-bit Real-Time Counter with Battery Backup System (VBAT) for RTC retention. An AVR XMEGA microcontroller is a member of Microchip's 8/16-bit RISC MCU family that extends the classic AVR core with a wider 16-bit instruction path, hardware DMA, an event system for peripheral-to-peripheral signaling without CPU intervention, and rich analog peripherals. XMEGA parts sit between the 8-bit ATmega family and 32-bit ARM Cortex-M parts, making them well suited to mixed-signal embedded designs that need deterministic I/O timing and low active power. Key features of the ATXMEGA256A3BU include 256 KB Flash with an 8 KB boot code section, 16 KB SRAM, 4 KB EEPROM, 34 programmable I/O lines, dual 12-bit ADC, two 12-bit DAC channels, multiple USART/SPI/TWI interfaces, AES/DES crypto engine, and an RTC subsystem with VBAT pin (PF5) that keeps the 32-bit RTC running during main-battery loss. The 32 MHz peak core speed with a single-cycle 16-bit ALU delivers roughly 32 MIPS throughput while consuming only a few mA in active mode. The A3BU silicon uses Microchip's picoPower technology with multiple sleep modes down to sub-microamp standby, plus an event system that lets peripherals trigger each other so the CPU can stay asleep longer. The Battery Backup System preserves RTC state across main-power failures by switching the RTC supply onto VBAT, which is a key feature absent from the otherwise similar ATxmega256A3U. Typical applications include industrial sensor hubs, smart metering, building automation, low-power wireless sensor nodes paired with an external radio, motor control, USB device/embedded hosts, and battery-backed data loggers. The 32-bit RTC plus VBAT makes it a strong fit for any design that must keep wall-clock time through power cycles. When designing with this MCU, route VBAT through a backup supercap or coin cell, decouple the main VCC with 100 nF plus 4.7 µF bulk caps adjacent to each supply pin, and reserve a dedicated 6-pin PDI header for in-system programming because the QFN package cannot be socketed on most production boards. This page synthesizes distributor stock and pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
ATXMEGA256A3U-AN - 32MHz 256KB Flash 8/16-bit AVR MCU | Microchip
ATXMEGA256A3U-AN

ATXMEGA256A3U-AN - 32MHz 256KB Flash 8/16-bit AVR MCU | Microchip

The Microchip Technology ATXMEGA256A3U-AN is a low-power, high-performance 8/16-bit AVR XMEGA A3U microcontroller running at up to 32 MHz with 256 KB self-programming Flash program memory, 16 KB SRAM and 4 KB EEPROM, housed in a 64-pin TQFP (14x14 mm) package rated for 105 °C operation. The device delivers up to 32 MIPS throughput and integrates a 4-channel DMA controller, an 8-channel event system, a cryptographic AES/DES engine on the A3U family, and full-speed USB 2.0 device support, making it a peripheral-rich member of the Atmel AVR enhanced RISC architecture. Background Knowledge: An 8/16-bit AVR XMEGA microcontroller is a member of the RISC microcontroller family, sitting in the hierarchy 8-bit MCU -> AVR core -> XMEGA family -> A3U series -> 64-pin TQFP class. It executes most instructions in a single clock cycle, providing close to 1 MIPS per MHz, and combines deterministic interrupt response with rich analog and digital peripherals for embedded control. Key features include 256 KB Flash with 8 KB boot section, 4 KB EEPROM endurance up to 100,000 cycles, 16 KB SRAM, an internal 32 MHz calibrated oscillator, multiple USART/SPI/TWI interfaces, and a 12-bit ADC with up to 2 MSPS sampling. The A3U suffix designates the USB-equipped sub-family with hardware AES and DES crypto engines. The 1.6 V to 3.6 V supply range supports battery and industrial 3.3 V rails, while sleep current under 1 µA with RTC running enables energy-harvesting and portable designs. Typical applications include USB peripherals, building and industrial automation, motor control, sensor hubs, and human-machine interface (HMI) panels. The integrated full-speed USB 2.0 device interface is widely used for HID, CDC, and vendor-class peripherals without an external transceiver. Hardware AES/DES acceleration offloads secure communication tasks from the CPU, while the 12-bit ADC and high-resolution timers simplify BLDC and stepper motor control loops. Designers should size decoupling per 64-pin TQFP power pins and follow the Atmel AVR1003 application note for USB hardware design. Use the Atmel AVR Studio / Microchip Studio toolchain with the AVR Dragon or JTAGICE3 for in-system debug. The XMEGA A3U datasheet and AVR1020 migration note are the authoritative references for peripheral mapping and migration from earlier A3 (non-U) parts.

RFQ संपर्क
ATXMEGA256A3U-AU - 256KB Flash 32MHz 8/16-bit AVR XMEGA MCU | Microchip
ATXMEGA256A3U-AU

ATXMEGA256A3U-AU - 256KB Flash 32MHz 8/16-bit AVR XMEGA MCU | Microchip

The Microchip Technology ATXMEGA256A3U-AU is a low-power, high-performance 8/16-bit AVR XMEGA A3U microcontroller delivering up to 32 MIPS throughput at 32 MHz, integrating 256 KB of self-programming Flash program memory plus an 8 KB boot code section in a 64-pin TQFP (14x14 mm) package. It is part of the AVR enhanced RISC architecture family with single-cycle instruction execution. An 8/16-bit microcontroller (MCU) is a programmable system-on-a-chip that combines a CPU, Flash program memory, SRAM, EEPROM, and a rich set of peripherals on a single die. MCUs are the highest-volume category of integrated circuits and serve as the digital core of nearly every embedded product - from battery-powered IoT nodes to industrial motor drives - occupying the middle of the silicon hierarchy between simple discrete logic and full microprocessors. Key features include 16 KB SRAM, 4 KB EEPROM, a 4-channel DMA controller, an 8-channel event system, and 34 programmable I/O lines. The device operates from a 2.7V to 3.6V supply, supports LVTTL/LVCMOS-compatible I/O, and includes multiple communication interfaces (USART, SPI, TWI) plus a 12-channel 12-bit ADC and analog comparators. The A3U variant adds a USB 2.0 Full-Speed device interface absent from the non-U A3 series. The ATXMEGA256A3U uses a Harvard-architecture AVR CPU with a 3-stage pipeline and hardware multiplier, achieving 1 MIPS per MHz. The peripheral event system lets peripherals trigger one another without CPU intervention, freeing the core for application code. The 4-channel DMA controller can move data between peripherals and memory autonomously, further reducing CPU load for streaming or signal-processing tasks. Typical applications include building automation, industrial control, low-power IoT sensor nodes, motor control, metering, USB peripherals, and human-machine interfaces (HMI) with LCD segments. The wide peripheral set and large Flash make it well suited to data logging, LCD-keypad control panels, and protocol bridges that previously required external logic. When designing with this MCU, allocate adequate decoupling (typically 100 nF plus 10 uF bulk) close to each VCC pin, and follow the XMEGA AU manual guidance for PDI programming interface routing. The 64-pin TQFP footprint is shared with the rest of the ATxmega A3U family, allowing easy migration to the 192A3U, 128A3U, or 64A3U derivatives by code recompilation.

RFQ संपर्क
ATXMEGA256C3-MH - 256KB Flash 32MHz XMEGA C3 MCU | Microchip
ATXMEGA256C3-MH

ATXMEGA256C3-MH - 256KB Flash 32MHz XMEGA C3 MCU | Microchip

The Microchip Technology ATXMEGA256C3-MH is a high-performance, low-power 8/16-bit AVR XMEGA C3 microcontroller featuring 256 KB in-system programmable Flash (with 8 KB boot code section and read-while-write capability), 4 KB EEPROM, 16 KB SRAM, and a 32 MHz CPU core, housed in a 64-pin QFN (9x9 mm) package. What is an AVR XMEGA microcontroller? The XMEGA family is a modernized successor to the classic 8-bit AVR architecture, combining a 16-bit instruction set with an 8-bit datapath (often described as 8/16-bit). Within the broader taxonomy it sits as: microcontroller -> embedded MCU -> 8/16-bit MCU -> AVR -> AVR XMEGA -> XMEGA C3 series. The C3 sub-series adds high-speed analog and a four-channel event system, positioning it above entry-level ATmega parts in both peripheral count and computational throughput. Key differentiating specifications include 50 general-purpose I/O lines, five 16-bit timer/counters with capture/compare/PWM, a 16-bit real-time counter, a four-channel event system, a programmable multi-level interrupt controller, USB Device and AES/DES crypto engine. The 32 MHz core delivers 32 MIPS with single-cycle execution, while peripheral DMA on 4 channels reduces CPU load for data movement. The architecture integrates an on-chip programmable gain amplifier (PGA), a 12-bit 2 MSPS ADC, a 12-bit 1 MSPS DAC, and multiple communication interfaces including USART, SPI, TWI (I2C), and full-speed USB. The 1.6 V to 3.6 V wide operating voltage and five software-selectable sleep modes with sub-microamp standby current make it well suited to battery-aware designs that need to wake on event. Typical applications include industrial control panels, building automation (HVAC, lighting, metering), USB peripherals (HID, CDC, custom class), motor control boards, handheld battery-powered instruments, factory automation nodes, and medical/clinical devices. The combination of large Flash, integrated crypto, and DMA makes it a strong fit for networked sensor hubs and secure IoT edge nodes. Designers should note that pin count and footprint drive PCB layout decisions. The 64-QFN variant is the highest-density option in the C3 family. Power estimation should include peripheral current draw and clock tree contributions, especially when high-speed peripherals are enabled. This page synthesizes distributor pricing, drop-in alternatives in the same 64-QFN footprint, and practical design notes not assembled on the manufacturer datasheet or distributor catalog pages.

RFQ संपर्क
ATXMEGA32A4-AU - 32KB Flash 32MHz 8/16-bit AVR XMEGA MCU
ATXMEGA32A4-AU

ATXMEGA32A4-AU - 32KB Flash 32MHz 8/16-bit AVR XMEGA MCU

The Microchip Technology ATXMEGA32A4-AU is a low-power, high-performance 8/16-bit AVR XMEGA A4 microcontroller with 32 KB self-programming Flash, 4 KB SRAM, 1 KB EEPROM, and a 4 KB boot code section, packaged in a 44-pin TQFP (10x10 mm). It runs at up to 32 MHz delivering 32 MIPS throughput, with 34 general-purpose I/O lines, a 4-channel DMA controller, an 8-channel event system, and a programmable multi-level interrupt controller. Operating voltage range is 1.6 V to 3.6 V per the manufacturer datasheet. An AVR XMEGA microcontroller is an advanced 8/16-bit RISC architecture MCU that extends the classic AVR core with a richer peripheral set, DMA-driven I/O, an event system for inter-peripheral signaling, and a more capable interrupt controller, while keeping the AVR instruction set and toolchain compatibility. XMEGA sits above classic ATmega in the Microchip (formerly Atmel) AVR taxonomy, between ATmega and the SAM Cortex-M families in terms of performance and peripheral depth. It targets low-power embedded designs that need deterministic I/O without leaving the AVR ecosystem. Key features include 32 KB in-system programmable Flash with read-while-write support, 1 KB internal EEPROM for non-volatile data, five flexible 16-bit Timer/Counters with compare and PWM modes, two TWI (I2C-compatible) interfaces, five USARTs, two SPI ports, a 16-bit Real-Time Counter (RTC), a 12-channel 12-bit ADC, and AES/DES crypto accelerators. The DMA controller and event system offload repetitive I/O from the CPU, enabling efficient sensor and communication pipelines. The integrated bandgap reference and on-chip temperature sensor simplify analog designs. Architecturally, the A4 series uses the XMEGA core with single-cycle ALU operations, hardware multiplier, and a peripheral event system that allows peripherals to trigger each other without CPU intervention. The result is deterministic low-latency I/O at very low active currents, making the A4 family well suited to battery-powered measurement, sensor hubs, and human-interface products. Typical applications include industrial sensor nodes, smart metering, building automation controllers, low-power wireless sensor hubs (paired with an external radio), USB/HID peripherals, motor control edge nodes, and consumer human-interface devices. Choose the ATXMEGA32A4-AU when you need AVR toolchain continuity with XMEGA-grade peripherals in a 44-pin TQFP. Designers should plan a stable 1.6 V to 3.6 V rail with sufficient decoupling near the AVDD pins, route the event system lines carefully to avoid noise coupling into ADC inputs, and verify the boundary scan / PDI programming interface is accessible for in-system firmware updates. Selecting the A4 family preserves AVR toolchain investment while adding modern peripherals. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the standalone manufacturer datasheet.

RFQ संपर्क
ATXMEGA32A4-CU - 32MHz 32KB AVR Microcontroller | Microchip
ATXMEGA32A4-CU

ATXMEGA32A4-CU - 32MHz 32KB AVR Microcontroller | Microchip

The Microchip Technology ATXMEGA32A4-CU is an 8/16-bit AVR XMEGA A4 microcontroller operating at 32 MHz, with 32 KB of self-programming Flash, 4 KB of SRAM, and a 49-VFBGA 5 x 5 mm package. Its operating supply range is 1.6 V to 3.6 V according to the Mouser product listing. The device combines an AVR RISC processor with a hardware multiplier and integrated high-speed peripherals for compact embedded-control designs. An 8/16-bit microcontroller is a programmable semiconductor that executes firmware, reads sensor inputs, controls actuators, and manages communications in an embedded system. The ATxmega family belongs to the broader hierarchy of microcontrollers, embedded processors, and semiconductor components. Unlike a general-purpose application processor, this device emphasizes deterministic peripheral operation, event handling, direct memory access, and low-power embedded control while retaining familiar AVR software development. The ATXMEGA32A4-CU provides 32 KB of self-programming Flash program memory, including a 4 KB boot-code section, together with 4 KB SRAM and 1 KB EEPROM. Its integrated peripherals include a four-channel DMA controller, an eight-channel event system, an external bus interface, and communication resources listed for the family as five USARTs and two Two-Wire Interfaces. The 34 I/O pins provide connections for sensors, actuators, human-interface inputs, and external buses. The XMEGA architecture uses an event system to connect peripherals without requiring continuous CPU polling. This can reduce software overhead in designs that must respond to timer, communication, or external-signal events. The four-channel DMA controller is useful for transferring data between memory and peripherals, while self-programming Flash supports firmware maintenance and bootloader-based updates. Operating at 32 MHz provides additional processing headroom for protocol handling and control-loop calculations. Typical uses include industrial automation modules, compact sensor nodes, data-logging instruments, communication equipment, and low-power embedded controllers. Its 49-VFBGA package is particularly appropriate for space-constrained products where a reduced package area is valuable. Board assembly requires suitable BGA manufacturing and inspection capability, so designers must account for package geometry, solder-mask design, thermal management, and assembly yield during volume production. A key design consideration is that the small 5 x 5 mm BGA is not a simple through-hole or two-row-package substitution. Existing PCB layouts must match the exact 49-ball footprint, ball assignments, exposed-pad requirements, and manufacturer land pattern. Firmware should also be validated at the intended 1.6 V to 3.6 V supply conditions because timing and peripheral performance can vary with voltage and frequency. This page combines verified manufacturer and distributor specifications with package, sourcing, application, and replacement guidance. It also distinguishes genuine same-footprint alternatives from related XMEGA devices that have different memory sizes or order codes, helping engineers avoid treating functional similarity as drop-in compatibility.

RFQ संपर्क
ATXMEGA32A4-MH - 32MHz AVR Microcontroller | Microchip Technology
ATXMEGA32A4-MH

ATXMEGA32A4-MH - 32MHz AVR Microcontroller | Microchip Technology

Microchip Technology ATXMEGA32A4-MH is an 8/16-bit AVR XMEGA A4 microcontroller operating up to 32 MHz with 32 KB of self-programming Flash memory and a 44-VQFN 7 x 7 mm package. The device includes 4 KB of boot-code section space, 4 KB SRAM, 1 KB EEPROM, a four-channel DMA controller, an eight-channel event system, and an external bus interface. Its operating-voltage information spans 1.6 V to 3.6 V, while one distributor specification lists a 2.7 V to 3.6 V supply range for this package. An 8/16-bit AVR microcontroller is a compact embedded-processing component within the microcontroller, semiconductor, and embedded-systems hierarchy. The ATXMEGA family combines a Harvard-style RISC core, memory, timers, communication peripherals, and general-purpose I/O in one package. Compared with larger 32-bit microcontrollers, it provides a focused platform for real-time control, data acquisition, human-interface equipment, and low-power embedded products where 32 KB Flash is sufficient and deterministic peripheral operation is valuable. The principal features of the ATXMEGA32A4 include a 32 MHz maximum clock, 32 KB Flash organized as 16K x 16, 4 KB SRAM, 1 KB EEPROM, and 34 I/O ports. Peripherals include a four-channel DMA controller, an eight-channel event system, and an external bus interface. The 44-VQFN package provides a compact surface-mount solution for space-constrained PCB layouts, although its fine pitch requires careful assembly and land-pattern design. At the architectural level, the AVR enhanced RISC core executes instructions in a single clock cycle and can approach 1 MIPS per MHz. The DMA controller can transfer data without occupying the CPU for each peripheral transaction, while the event system routes peripheral signals between timer, comparator, and communication resources. This combination supports responsive control loops and coordinated sampling in industrial, communication, and consumer equipment. Typical uses include industrial monitoring, building-control interfaces, sensor hubs, programmable logic controllers, data loggers, and compact communication equipment. The combination of 34 I/O ports, four DMA channels, and an event system is particularly useful when multiple timers, counters, or serial peripherals must operate in a coordinated manner. A system requiring more Flash, SRAM, or peripherals may require a larger ATxmega model rather than this 32 KB A4 device. Designers should verify the exact pin functions, alternate-function mappings, clock requirements, and power behavior against the manufacturer datasheet before layout release. The 44-VQFN footprint requires a conservative solder mask and paste pattern, and unused pins must be connected according to the device guidance. Supply-voltage requirements should also be checked against the specific clock, peripheral, and operating-temperature conditions used by the product. This page consolidates verified distributor inventory, manufacturer feature information, package details, commercial pricing, application guidance, and design considerations. It also distinguishes genuine same-footprint alternatives from related devices that use different packages or materially different memory configurations, helping engineers avoid a replacement that cannot be soldered onto the existing PCB.

RFQ संपर्क
ATXMEGA32C3-AN - 32MHz 32KB Flash AVR Microcontroller | Microchip
ATXMEGA32C3-AN

ATXMEGA32C3-AN - 32MHz 32KB Flash AVR Microcontroller | Microchip

The Microchip Technology ATXMEGA32C3-AN is an 8/16-bit AVR XMEGA microcontroller operating at 32 MHz with 32 KB of in-system programmable Flash, 2 KB of EEPROM, 4 KB of SRAM, and a 64-TQFP 14 x 14 mm package. It is designed for embedded systems that require deterministic real-time control, flexible peripherals, and a compact surface-mount footprint. The device supports read-while-write operation and includes a dedicated 8 KB boot-code section. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals into one device. The ATXMEGA32C3 belongs to the hierarchy of 8/16-bit microcontrollers, embedded processors, and programmable control ICs. Its AVR architecture combines an instruction set optimized for embedded control with event-system and interrupt resources that help coordinate timing-sensitive tasks without relying entirely on software polling. Key features include 32 KB of Flash memory, 2 KB of EEPROM, 4 KB of SRAM, 50 general-purpose I/O pins, and a four-channel event system. The manufacturer describes the family as a programmable multilevel interrupt controller with 32 MHz processing. A 1.6 V to 3.6 V operating range supports low-voltage embedded systems, while the listed temperature rating of 105 C supports applications beyond conventional commercial temperature limits. The ATXMEGA family architecture places communication and timing functions close to the CPU. The event system can connect peripherals through direct event channels, reducing CPU intervention for deterministic tasks. The four-channel event system is particularly useful for high-speed timing, sensor acquisition, and signal-generation workflows where predictable event relationships are more valuable than raw instruction throughput. Read-while-write Flash operation can also simplify firmware-update or boot-related implementations. Typical uses include industrial control modules, compact sensor nodes, data-acquisition equipment, motor-control peripherals, communications equipment, and embedded accessories. Its 64-pin package provides substantially more I/O than smaller microcontroller packages while remaining manageable for automated assembly and multilayer PCB layouts. The 32 MHz clock rate and 32 KB memory footprint suit control-oriented designs that do not require a high-end processor or large graphical user interface. Design around the 1.6 V to 3.6 V supply range, decoupling requirements, clock configuration, programming interface, and exposed peripheral pins specified in the manufacturer datasheet. Confirm boot-loader, USB, ADC, timer, and communications requirements during device selection because firmware and peripheral availability depend on the exact family variant. This page combines manufacturer specifications, purchasing guidance, and drop-in alternatives to support engineering evaluation. For a new design, ATXMEGA32C3-AN offers a useful balance of processing speed, memory, real-time peripherals, and board area. It is most appropriate when deterministic event handling and AVR software compatibility matter more than the very small package area or low cost of a minimal 8-bit controller.

RFQ संपर्क
ATXMEGA32C3-AU - 32MHz 32KB Flash MCU | Microchip | TQFP-64
ATXMEGA32C3-AU

ATXMEGA32C3-AU - 32MHz 32KB Flash MCU | Microchip | TQFP-64

The Microchip Technology ATXMEGA32C3-AU is an 8/16-bit AVR XMEGA C3-series microcontroller operating at up to 32 MHz, with 32 KB of Flash memory, 2 KB of EEPROM, and 4 KB of SRAM in a 64-pin TQFP package. It is designed for compact embedded systems that require deterministic control, flexible serial communications, and low-power operation without relying on a high-pin-count package. A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, data memory, peripherals, and interface circuitry on one device. Within the embedded-control hierarchy, the ATXMEGA32C3 belongs to the AVR 8/16-bit MCU family and uses the Harvard-style AVR architecture, which separates program-memory access from the data-memory path. This structure supports efficient instruction execution in applications involving sensors, communication interfaces, motor control, and local human-machine interaction. The ATXMEGA32C3-AU combines 32 KB of in-system programmable Flash with read-while-write capability, 2 KB of EEPROM, and 4 KB of SRAM. Its four-channel event system can coordinate timing-sensitive tasks without excessive interrupt servicing. The device also provides a 12-bit ADC, multiple timer/counter resources, and serial interfaces suitable for industrial, consumer, and communication-oriented embedded products. The industrial-temperature ordering designation identifies it for extended-temperature equipment applications. Its 32 MHz operating speed provides useful performance for protocol handling, signal conditioning, sampling, and supervisory control. The four-channel event system is particularly valuable when several peripheral actions must occur with predictable timing. Program memory can be updated in-system, supporting configuration changes and firmware maintenance, while read-while-write operation allows code execution to continue when flash locations do not overlap the active program section. Typical uses include industrial sensor nodes, building-automation controllers, motor-control interfaces, compact data loggers, communication modules, and embedded measurement equipment. The combination of SRAM, EEPROM, timers, ADC channels, and serial peripherals allows one device to consolidate functions that might otherwise require several discrete components. The primary design consideration is package and firmware compatibility. A 64-pin TQFP footprint requires adequate PCB routing space, and new designs should follow the Microchip pin description, recommended decoupling, clock, and programming-interface layouts. Firmware replacement also requires review of boot sections, interrupt vectors, peripheral resources, and application-specific timing rather than treating every electrically similar device as functionally identical. This product record combines manufacturer specifications, package details, sourcing guidance, and engineering-focused design guidance to support initial component selection and board-level implementation. It also distinguishes exact ordering variants from genuine pin-compatible alternatives so that footprint and firmware decisions are not based solely on a matching package name.

RFQ संपर्क
ATXMEGA32C3-MH - 32KB Flash 32MHz 8/16-bit AVR XMEGA MCU | Microchip
ATXMEGA32C3-MH

ATXMEGA32C3-MH - 32KB Flash 32MHz 8/16-bit AVR XMEGA MCU | Microchip

The Microchip Technology ATXMEGA32C3-MH is a high-performance, low-power 8/16-bit AVR XMEGA C3 microcontroller running at 32 MHz, integrating 32 KB of in-system programmable Flash memory (with an 8 KB boot-code section and read-while-write capability), 2 KB EEPROM and 4 KB SRAM, all housed in a 64-pin VQFN (9x9 mm) exposed-pad package. An 8/16-bit microcontroller (MCU) is a single-chip computer built around an 8- or 16-bit data path that integrates a CPU core, non-volatile Flash program memory, volatile SRAM data memory, EEPROM for parameter storage, plus a rich set of on-chip peripherals (timers, ADC/DAC, communication controllers, GPIO). The ATXMEGA32C3 belongs to the XMEGA family in the broader hierarchy: 8/16-bit MCU -> microcontroller -> embedded processor -> semiconductor. It uses the AVR RISC instruction set with hardware multiplier, executes most instructions in a single clock cycle, and is targeted at industrial-grade, low-power embedded designs that need deterministic real-time response. Key features of the ATXMEGA32C3-MH include four flexible 16-bit Timer/Counter modules, a 12-channel event system, a four-channel DMA controller that moves data without CPU intervention, a 12-bit ADC and 12-bit DAC, USB device support, AES/DES crypto acceleration, and an operating voltage range of 1.6 V to 3.6 V. Its 32 MHz core delivers up to 32 MIPS of throughput, and the integrated PicoPower technology reduces active and sleep-mode current. Architecturally, the device pairs an event-driven peripheral fabric with the DMA controller, allowing analog conversion, packet transmission, and timer capture to run autonomously while the CPU sleeps. This architecture is well-suited to deterministic, low-latency control applications such as sensor hubs, motor control, and human-interface subsystems. Typical applications include industrial sensor interfaces, USB-enabled consumer devices, building automation controllers, smart-metering subsystems, and human-machine interface (HMI) panels. The wide 1.6V-3.6V supply range also allows direct battery operation. When designing with this device, ensure the 64-pin VQFN exposed pad is soldered to a sufficient ground copper pour for thermal and electrical performance. Decouple VDD with at least one 100 nF ceramic capacitor per supply pin placed as close as possible to the package. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing a single reference for engineers evaluating the ATXMEGA32C3-MH for new designs.

RFQ संपर्क
ATXMEGA32C3-MHR - 32KB Flash 8/16-bit AVR XMEGA MCU 64-QFN
ATXMEGA32C3-MHR

ATXMEGA32C3-MHR - 32KB Flash 8/16-bit AVR XMEGA MCU 64-QFN

The Microchip Technology ATXMEGA32C3-MHR is a high-performance, low-power 8/16-bit AVR XMEGA C3 microcontroller integrating 32 KB of in-system programmable Flash memory (with an 8 KB boot code section that supports read-while-write operation), 2 KB EEPROM, and 4 KB SRAM, housed in a 64-pin 9x9 mm QFN package. It executes instructions in a single clock cycle and reaches up to 32 MHz CPU throughput, delivering nearly 1 MIPS per MHz while keeping active power consumption low. The part supports a 1.6 V to 3.6 V supply range and is qualified for industrial temperature operation. What is an AVR XMEGA microcontroller? The XMEGA family extends Atmel's AVR enhanced RISC architecture into the 8/16-bit microcontroller segment. It belongs to the wider hierarchy: microcontroller (MCU) -> 8/16-bit MCU -> AVR core MCU -> XMEGA family. XMEGA devices are positioned between classic 8-bit AVR microcontrollers and 32-bit ARM Cortex-M parts, offering richer peripherals (DMA, event system, crypto engine on some variants) than classic AVR while retaining a single-cycle RISC core that is simple to program in C. Key features include a four-channel event system for inter-peripheral signaling without CPU intervention, a programmable multi-level interrupt controller, 50 general-purpose I/O pins, a full-speed USB device interface, multiple USART/SPI/TWI peripherals, a 12-bit ADC and DAC, and AES/DES crypto acceleration on selected variants. The 32 KB Flash supports application programming through boot-loader, JTAG, or PDI interfaces. Industrial-grade temperature range (-40C to +85C) and 1.6-3.6 V operation make it suitable for battery-powered and harsh-environment designs. A 12 mA maximum active supply current is specified in the brief, while sleep-mode currents are in the microamp range. Architecturally, the ATXMEGA32C3 uses the AVR enhanced RISC core with a multi-stage pipeline and Harvard bus architecture that allows instruction fetch and memory access to overlap. The four-channel event system routes peripheral triggers (timer, ADC, DMA) directly between peripherals, offloading the CPU. The 64-pin QFN package exposes the full peripheral set and supports up to 50 GPIO lines. Typical applications include industrial control panels, USB human-interface devices (HID), smart sensors with on-board crypto, low-power IoT edge nodes, building automation, and consumer electronics with touch or display interfaces. The AES/DES hardware accelerator enables secure firmware and authenticated sensor links. The part is widely used in designs that migrate from older ATmega MCUs but need more peripherals and lower active power. A key design consideration is decoupling: place 100 nF and 1 uF ceramic capacitors close to each VCC pin and provide adequate ground stitching under the QFN thermal pad to minimize EMI. Program/debug is performed through the PDI (Program and Debug Interface) two-wire protocol rather than JTAG on this device family. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ संपर्क
ATXMEGA32C4-AU - 32MHz 32KB MCU 44-TQFP | Microchip
ATXMEGA32C4-AU

ATXMEGA32C4-AU - 32MHz 32KB MCU 44-TQFP | Microchip

Microchip Technology ATXMEGA32C4-AU is an 8/16-bit AVR XMEGA C4 microcontroller operating at 32MHz, with 32KB Flash memory, 1KB EEPROM, and 4KB SRAM in a 44-pin TQFP package measuring 10mm by 10mm. The industrial-temperature device supports a 1.6V to 3.6V operating range and includes a 12-bit ADC. According to the manufacturer product page, the device also provides a four-channel event system and read-while-write Flash capabilities. An 8/16-bit microcontroller is a programmable semiconductor that combines a CPU core, nonvolatile program memory, data memory, and peripherals on one integrated circuit. The ATXMEGA32C4 belongs to the AVR XMEGA family, which extends the AVR enhanced RISC architecture into a larger 16-bit-oriented microcontroller platform. It sits within the hierarchy of microcontroller, embedded processor, semiconductor, and programmable control components used to monitor sensors and operate digital systems. The principal specifications include a 32MHz clock, 32KB of in-system programmable Flash divided into 16K by 16 organization, 4KB SRAM, and 1KB EEPROM. The 1.6V to 3.6V supply range supports low-voltage embedded designs, while the 12-bit ADC and four-channel event system provide analog measurement and hardware event-routing capabilities. The -AU suffix identifies the industrial-temperature ordering configuration shown in the verified distributor data. The AVR enhanced RISC architecture executes instructions in a single clock cycle and is designed for efficient embedded control. Read-while-write Flash allows program regions to remain accessible while another section is being programmed, while separate boot, SRAM, and EEPROM areas support firmware storage, working data, and nonvolatile parameter retention. The exact RAM organization, peripheral inventory, clock tree, and detailed analog performance should be confirmed in the manufacturer datasheet before final design release. Typical uses include industrial control modules, sensor-acquisition equipment, compact motor controllers, building automation nodes, and embedded instruments. The combination of 32KB Flash, 4KB SRAM, a 12-bit ADC, and a 32MHz processing clock is useful when a design needs moderate local computation without adopting a higher-pin-count or more complex system controller. The 44-TQFP package also exposes the mixed-signal and communication resources required by embedded control boards. Designers should verify the complete pin assignment, peripheral multiplexing, decoupling requirements, programming interface, and package drawing against the Microchip datasheet. Because the verified material confirms the TQFP44 package but does not provide a verified pin table, this listing does not infer individual signal names. PCB layouts should also preserve the manufacturer's recommended power, ground, and analog routing practices. This product record combines the verified manufacturer and distributor specifications, current pricing reference, package information, engineering-oriented use cases, and explicit data-gap controls. It also distinguishes confirmed device attributes from unverified details, helping engineers evaluate the ATXMEGA32C4-AU without mistaking packaging variants or functionally related devices for verified drop-in replacements.

RFQ संपर्क