Produk (21.000+)

EFM32TG825F8-BGA48T - 32MHz ARM MCU | Silicon Labs
EFM32TG825F8-BGA48T

EFM32TG825F8-BGA48T - 32MHz ARM MCU | Silicon Labs

Silicon Labs EFM32TG825F8-BGA48T is a 32-bit ARM Cortex-M3 microcontroller rated for operation up to 32 MHz, with 8 KB of Flash memory and 2 KB of RAM in a 48-BGA (4x4 mm) package. It provides 37 digital I/O pins, two 16-bit timers, AES hardware, three operational amplifiers, and support for an 8x11 LCD. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals on one device. The EFM32TG825F8-BGA48T belongs to the Tiny Gecko family of 32-bit microcontrollers, combining the ARM Cortex-M3 architecture with energy-saving modes and fast wake-up behavior. This hierarchy places it above the Cortex-M3 core and within the broader embedded MCU and semiconductor categories. The device operates from 1.98 V to 3.8 V and supports an industrial temperature range of -40°C to 85°C. Its operating frequency of 32 MHz provides useful processing performance for embedded control tasks, while the integrated AES accelerator, three operational amplifiers, LCD capability, and low-power architecture reduce the need for external discrete components. The 8 KB Flash configuration suits compact firmware and code-constrained embedded nodes. Silicon Labs positions this MCU around energy-efficient operation, autonomous sensor monitoring in Deep Sleep Mode, capacitive sensing, and rapid wake-up from energy-saving states. Two 16-bit timers support periodic timing, motor-control-related timing, or general event counting. The Serial Wire Debug interface and pre-programmed UART bootloader support development, diagnostics, and field configuration without requiring a separate programming interface in the target application. Typical uses include compact sensor nodes, capacitive buttons, low-power industrial monitors, small LCD instruments, wearable accessories, and embedded control modules. Its 37 I/O pins provide access to sensors and actuators, while the operational amplifiers can condition analog inputs close to the MCU. Designers should still verify each peripheral pin assignment against the device's pin multiplexing and board-level power requirements before finalizing a PCB. The principal design trade-off is its 8 KB Flash limit. It works well for compact, event-driven firmware but may require careful code organization when the application includes extensive libraries, a bootloader, or complex communications stacks. The 3.8 V maximum supply also means the device is intended for low-voltage systems rather than direct connection to higher-voltage industrial rails. This product record combines the manufacturer device information with package, memory, interface, and low-power design guidance. It also identifies same-family hardware alternatives, practical selection criteria, and engineering considerations that help teams determine whether this 48-BGA MCU fits their PCB and firmware requirements.

Permintaan RFG Kontak
EFM32TG825F8-D-BGA48 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32TG825F8-D-BGA48

EFM32TG825F8-D-BGA48 - 32MHz Cortex-M3 MCU | Silicon Labs

Silicon Labs EFM32TG825F8-D-BGA48 is a 32-bit ARM Cortex-M3 microcontroller operating up to 32 MHz, with 8 KB of Flash memory, 2 KB of RAM, and a 48-BGA (4 x 4 mm) package. Its 1.98 V to 3.8 V operating range makes it suitable for compact, low-energy embedded systems requiring efficient code execution and rapid wake-up behavior. An ARM Cortex-M3 microcontroller, or MCU, combines a processor core, memory, peripherals, and I/O in one integrated circuit. Within the semiconductor hierarchy, the EFM32TG825F8-D-BGA48 belongs to the 32-bit microcontroller family and uses the low-power Tiny Gecko platform. Its autonomous peripherals and energy-saving modes are intended to reduce the amount of CPU activity required for routine sensing, communications, and control tasks. The device operates at up to 32 MHz and includes 8 KB of Flash, 2 KB of RAM, 37 digital I/O pins, two 16-bit timers, LCD support, and AES capability. According to the manufacturer EFM32TG data sheet, the family consumes as little as 0.6 uA in Stop mode and 150 uA/MHz in Run mode. These characteristics support duty-cycled products in which the controller sleeps between infrequent events. The Tiny Gecko architecture combines an ARM Cortex-M3 processor with energy-management peripherals and high analog integration. Its wake-up interrupt controller can handle interrupt requests while the CPU is asleep, reducing the need for continuous polling. The 37 available digital I/O pins also provide substantial connection flexibility for sensors, displays, user interfaces, and external interface converters within the constraints of a 4 x 4 mm BGA footprint. Typical applications include energy-harvesting sensor nodes, compact industrial monitors, wearable accessories, connected home devices, low-power metering equipment, and portable products with small displays. The 8 KB Flash capacity favors control-oriented firmware with limited code storage, while the LCD and AES features support display-driven and security-conscious designs. A higher-memory family member is preferable when firmware, libraries, or update buffers require more space. Board design should preserve the separation and decoupling of AVDD_x, VDD_DREG, and IOVDD_x as described in the EFM32TG data sheet. Place supporting capacitors close to their assigned supply pins, keep sensitive analog and communication routes away from fast digital switching nodes, and follow the manufacturer hardware-design guidance before committing a new 48-BGA layout. This page organizes the EFM32TG825F8-D-BGA48's memory, power, package, and application characteristics into an engineering-focused selection guide. It also distinguishes same-package family alternatives by their verified differences, helping designers identify when a higher-Flash variant is preferable and when the 8 KB configuration is sufficient for the intended firmware workload.

Permintaan RFG Kontak
EFM32TG840F16-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32TG840F16-QFN64

EFM32TG840F16-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32TG840F16-QFN64 is an ARM Cortex-M3 32-bit microcontroller (MCU) with a maximum operating speed of 32 MHz, 16 kB of Flash memory, 4 kB of RAM, and 56 digital I/O pins in a 64-QFN 9x9 mm package. It belongs to the Tiny Gecko family of low-power embedded processors. A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, volatile data memory, and peripherals on one integrated circuit. The ARM Cortex-M3 provides the instruction set and processing foundation, while Flash stores the firmware and RAM supports stack operations, data handling, and peripheral activity. The Tiny Gecko family adds energy-saving modes and fast wake-up behavior for systems that spend substantial time idle. The EFM32TG840F16-QFN64 operates at speeds up to 32 MHz and provides 16 kB of Flash, 4 kB of RAM, and 56 digital I/O pins. Two 16-bit timers support periodic timing, event counting, and basic motor or control functions. Its low-power architecture makes it suitable for battery-operated equipment, connected sensors, compact industrial controls, and other applications where average energy consumption matters as much as processing capability. The 64-QFN package supports dense PCB layouts while exposing 56 digital I/O pins for external interfaces. Its peripheral set and energy-management features allow a design to remain in a low-power state during idle periods and resume operation quickly when work is required. This combination is useful in portable measurement, industrial monitoring, and low-power embedded control systems. Typical uses include sensor nodes, small environmental monitors, industrial condition-monitoring devices, battery-powered accessories, and embedded control modules. Designers should allocate memory carefully for firmware, stack depth, and buffered data, and should preserve the recommended decoupling and exposed-pad layout shown in the manufacturer hardware design guidance. The most important design consideration is balancing performance against duty cycle. Running the Cortex-M3 core at 32 MHz supports responsive computation, but a low-energy application can often spend most of its time in a lower-power mode. Firmware can then use timers, interrupts, and wake-up sources to perform work only when needed. This product overview consolidates the core specifications, package details, practical design guidance, sourcing questions, and verified family alternatives for engineers evaluating the EFM32TG840F16-QFN64. It also distinguishes true same-footprint alternatives from devices that would require a PCB redesign.

Permintaan RFG Kontak
EFM32TG840F32-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32TG840F32-QFN64

EFM32TG840F32-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32TG840F32-QFN64 is a 32-bit ARM Cortex-M3 Tiny Gecko microcontroller operating up to 32 MHz, with 32 KB of Flash memory, 4 KB of RAM, 56 digital I/O pins, and two 16-bit timers in a 64-QFN 9 x 9 mm package. The device is designed for energy-sensitive embedded applications that require efficient processing, fast wake-up behavior, and low-energy operating modes. A microcontroller is a programmable system-on-chip that integrates a processor core, memory, digital I/O, timers, communication peripherals, and supporting power-management functions. The EFM32 Tiny Gecko belongs to the hierarchy of microcontroller ICs, embedded processors, and general-purpose semiconductors. Its ARM Cortex-M3 architecture provides a 32-bit instruction set and up to 32 MHz operating speed, while the energy-management architecture supports battery-operated and intermittently powered systems. The EFM32TG840F32-QFN64 provides 32 KB of Flash for firmware and 4 KB of RAM for working data. Its 56 digital I/O pins support external sensors, displays, communication interfaces, and control signals. Two 16-bit timers add resources for periodic events, timing, input capture, or output comparison. The listed distributor records also identify the device as an LCD and AES MCU, indicating support for display-oriented and security-related application requirements. The device is built around the low-power Tiny Gecko platform, which combines a conventional Cortex-M3 processing core with energy-saving modes and short wake-up times. This architecture is useful when the system spends much of its operating life in a low-power state and must resume measurement or control activity quickly. The 32 MHz maximum clock also provides sufficient performance for protocol handling, sensor fusion, user-interface logic, and supervisory tasks in compact embedded products. Typical applications include battery-powered sensor nodes, industrial condition-monitoring equipment, building-control endpoints, portable health and wellness products, small motor-control systems, and low-power connected instruments. Designers should select the appropriate operating voltage, clock configuration, memory layout, and peripheral assignments from the manufacturer documentation before finalizing the PCB and firmware. A critical hardware consideration is exposed-pad thermal management in the 64-QFN package. The exposed pad should be connected to the ground plane using the manufacturer’s recommended land pattern and thermal-via arrangement, while supply and ground connections should be routed to minimize noise and voltage loss. This product page consolidates verified manufacturer and distributor information, practical package guidance, and an honest assessment of available drop-in alternatives. It also distinguishes verified facts from parameters that remain unavailable in the supplied source data, helping engineers avoid unsupported substitutions or assumptions.

Permintaan RFG Kontak
EFM32TG840F8-D-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32TG840F8-D-QFN64

EFM32TG840F8-D-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs

Silicon Labs EFM32TG840F8-D-QFN64 is a 32-bit ARM Cortex-M3 microcontroller rated up to 32 MHz, with 8 kB Flash memory, 2 kB RAM, and 56 digital I/O pins in a 64-QFN package. Its compact 9 x 9 mm footprint supports energy-conscious embedded systems where board area, processing performance, and low-power operation are important. A microcontroller is a programmable semiconductor that integrates a CPU, memory, peripherals, and I/O into one device. The EFM32 Tiny Gecko family belongs to the broader 32-bit MCU and embedded-processor hierarchy. By combining an ARM Cortex-M3 core with energy-saving modes and fast wake-up behavior, the platform supports systems that spend substantial time in low-energy states while retaining deterministic control and communication functions. The EFM32TG840F8-D-QFN64 provides 8 kB of Flash for firmware, 2 kB of RAM for working data, 56 digital I/O pins, and two 16-bit timers. Its 32 MHz operating speed is suitable for sensor aggregation, low-power control, communications, and compact embedded-control tasks. The low-power architecture is particularly useful in battery-operated products where active processing time and sleep current directly affect service life. The device uses an ARM Cortex-M3 processor and combines two 16-bit timers with flexible GPIO resources for sensor, actuator, and communication interfaces. The manufacturer describes fast wake-up operation and energy-saving modes as central platform features. These characteristics allow firmware to remain responsive while minimizing unnecessary processor activity during idle intervals, although final energy consumption depends on the complete application, clock configuration, and peripherals enabled. Typical uses include low-power sensor nodes, industrial condition-monitoring equipment, connected instrumentation, compact environmental controls, and embedded accessories. The 56 I/O pins provide sufficient parallel connectivity for digital sensors, indicators, switches, and peripheral buses. The 8 kB Flash and 2 kB RAM are best suited to compact control loops and protocol stacks rather than storage-intensive, graphics-heavy, or large connectivity workloads. PCB designers should reserve the exposed-pad thermal and electrical connection specified by the manufacturer and place decoupling capacitors close to the supply pins. Keep sensitive analog and communication routes away from fast-switching nodes, follow the reference layout for the selected QFN land pattern, and verify wake-up, reset, and peripheral-routing behavior on the assembled board. This page organizes the device specifications, verified sourcing information, drop-in alternatives, application guidance, and practical PCB considerations. For a replacement decision, compare Flash, RAM, peripheral configuration, package land pattern, temperature grade, and software support rather than relying on the EFM32 or Tiny Gecko family name alone.

Permintaan RFG Kontak
EFM32TG840F8-QFN64 - 32MHz Low-Power MCU | Silicon Labs
EFM32TG840F8-QFN64

EFM32TG840F8-QFN64 - 32MHz Low-Power MCU | Silicon Labs

The Silicon Labs EFM32TG840F8-QFN64 is a 32 MHz ARM Cortex-M3 microcontroller with 8 kB Flash, 2 kB RAM, 56 digital I/O pins, and a 64-QFN package. It is designed for energy-sensitive embedded systems that require low-power operation, fast wake-up, and a compact surface-mount footprint. An ARM Cortex-M3 microcontroller is a 32-bit embedded processor within the microcontroller and semiconductor hierarchy. It combines a processor core, memory, peripherals, and I/O in one integrated circuit, allowing compact systems to execute firmware and control sensors, communications, and actuators without a separate processor. Silicon Labs positions this device in the EFM32 Tiny Gecko family, emphasizing low-energy techniques and energy-saving modes. The EFM32TG840F8-QFN64 operates at up to 32 MHz and includes 8 kB of Flash and 2 kB of RAM. Its 56 digital I/O pins provide substantial interface capacity for embedded control boards. The listed timer configuration includes two 16-bit timers, supporting periodic timing, input capture, output compare, and basic control-loop functions. The manufacturer and distributor results identify the device as an ARM Cortex-M3 Tiny Gecko MCU. The 64-QFN package, identified in distributor results as 64-QFN measuring 9 x 9 mm, supports compact PCB layouts while exposing many device connections. The verified listings also describe a 2.5 V or 3.3 V device configuration. Because the supplied data does not include a complete electrical timing table, pin-level function map, or detailed power-consumption values, those parameters remain marked as data needed rather than inferred. Typical applications include low-power sensor nodes, industrial monitoring equipment, connected embedded controls, compact consumer devices, and battery-operated systems. The MCU is suitable where a low-power 32-bit control platform and generous I/O count are more important than large onboard memory. Firmware memory and application complexity must be planned around the verified 8 kB Flash and 2 kB RAM limits. For PCB implementation, verify the exposed-pad connection, decoupling requirements, oscillator connections, programming interface, and all 64 package assignments against the manufacturer datasheet before layout release. Confirm the exact supply, I/O, peripheral, and timing constraints during schematic review. This page consolidates the verified manufacturer specifications, distributor listing details, sourcing links, and application-oriented engineering guidance for the EFM32TG840F8-QFN64 while explicitly identifying parameters that require confirmation from the datasheet.

Permintaan RFG Kontak
EFM32TG840F8-QFN64T - 32MHz ARM Cortex-M3 Tiny Gecko MCU | Silicon Labs
EFM32TG840F8-QFN64T

EFM32TG840F8-QFN64T - 32MHz ARM Cortex-M3 Tiny Gecko MCU | Silicon Labs

The Silicon Labs EFM32TG840F8-QFN64T is a 32-bit ARM Cortex-M3 microcontroller running at up to 32 MHz, with 8 KB of Flash memory and 2 KB of RAM, packaged in a 64-pin QFN (9x9 mm) surface-mount package with 56 digital I/O pins. It belongs to the EFM32 Tiny Gecko family, Silicon Labs' energy-focused 32-bit MCU line built around low-power design techniques, fast wake-up from deep sleep and multiple energy-saving modes. A microcontroller (MCU) is a single integrated circuit that bundles a CPU core, memory, and peripherals such as timers, ADCs, communication interfaces and GPIO. The EFM32 hierarchy runs from this general category down to 32-bit MCU -> ARM Cortex-M3 MCU -> energy-efficient 32-bit MCU -> Tiny Gecko family -> EFM32TG840 series. Because an MCU integrates the processor, memory and peripherals on one die, it replaces a discrete processor-plus-support-circuit design and reduces both board area and system power. Verified device features include an ARM Cortex-M3 core with 32-bit data path at up to 32 MHz clock speed, 8 KB Flash (8K x 8) program memory, 2 KB SRAM, 56 digital I/O pins, two 16-bit general-purpose timers, AES encryption hardware, three operational amplifiers, and support for an 8x20 character LCD segment display. The device is offered in a 64-QFN (9x9 mm) package. Architecturally, the Tiny Gecko platform prioritizes energy efficiency over raw throughput: it combines fast wake-up from energy-saving modes with low active current, which is the defining trade-off of the EFM32 family. At 32 MHz the Cortex-M3 core delivers roughly 32 MIPS of throughput, enough for protocol handling, sensor fusion and simple human-machine-interface logic while keeping active energy low compared with higher-frequency MCUs. Typical applications include battery-operated sensor nodes, compact industrial monitoring modules, energy-harvesting IoT endpoints, LED and LCD display controllers, wearable health accessories, and low-power metering peripherals. The on-chip AES block and operational amplifiers reduce the need for external components in secure and analog front-end designs. When designing around this part, keep the 8 KB Flash limit in mind: it fits compact protocol stacks and simple user code, but not large connectivity stacks. Decoupling and layout guidance in the manufacturer datasheet should be followed to keep analog channels and the LCD segment outputs noise-free. This page consolidates distributor pricing, verified device specifications, drop-in same-package alternatives and practical design notes in one place, so engineers can source and qualify the EFM32TG840F8-QFN64T without digging through multiple catalog listings.

Permintaan RFG Kontak
EFM32TG842F16-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32TG842F16-QFP64

EFM32TG842F16-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs

Silicon Labs EFM32TG842F16-QFP64 is an ARM Cortex-M3 microcontroller operating up to 32 MHz, with 16 KB of Flash memory, 4 KB of RAM, 53 digital I/O pins, and two 16-bit timers in a 64-TQFP 10 x 10 mm package. The device belongs to the EFM32 Tiny Gecko family and combines a 32-bit microcontroller core with energy-saving modes and fast wake-up behavior for embedded designs. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The Cortex-M3 architecture provides a 32-bit processing platform for control logic, while the EFM32 family adds low-power operating modes suitable for battery-powered instrumentation, sensors, industrial controls, and connected products. Fast wake-up capability helps reduce the time required to resume useful computation after a low-power interval. The EFM32TG842F16-QFP64 provides 16 KB of Flash for firmware and 4 KB of SRAM for working data. Its 53 digital I/O pins support external sensors, controls, indicators, and communication peripherals. Two 16-bit timers can provide counting, timing, pulse-width measurement, and periodic event generation. The listed operating supply range is 1.85 V to 3.8 V, allowing integration with common low-voltage embedded systems. The Tiny Gecko platform emphasizes energy efficiency through low-energy techniques, fast wake-up times, and energy-saving modes. This makes the MCU relevant to designs where average power consumption matters as much as processing performance. At the same time, the 32 MHz Cortex-M3 core provides sufficient control bandwidth for low-to-moderate complexity embedded workloads without requiring a higher-power processor. Typical uses include low-power sensor nodes, industrial monitoring equipment, metering devices, compact control panels, battery-operated instruments, and communication modules. Its 64-TQFP package exposes more I/O than smaller packages, making it useful when a design needs numerous discrete connections while retaining a surface-mount PCB footprint. Designers should account for the 1.85 V to 3.8 V supply range, confirm every peripheral and alternate-function assignment against the pin table, and provide appropriate decoupling close to the supply pins. Firmware should also use the documented low-power modes and wake-up sources to achieve the intended battery-life target rather than relying on processing speed alone. This product analysis combines the manufacturer device information with package, memory, timer, interface, and power attributes, alongside verified ordering variants and practical integration guidance. It is designed to help engineers compare capacity, pin availability, supply compatibility, and drop-in replacement options before committing a 64-TQFP PCB layout.

Permintaan RFG Kontak
EFM32TG842F32-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32TG842F32-QFP64

EFM32TG842F32-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32TG842F32-QFP64 is a 32-bit ARM Cortex-M3 microcontroller operating up to 32 MHz, with 32 KB of Flash memory, 4 KB of RAM, and 53 digital I/O pins in a 64-pin TQFP package. It is designed for energy-sensitive embedded systems that require low-power operation, fast wake-up behavior, and extensive peripheral integration. A microcontroller is a programmable system-on-chip that combines a processor core, memory, and peripherals such as timers, analog interfaces, communications controllers, and interrupt logic. The EFM32TG842F32-QFP64 belongs to the EFM32 Tiny Gecko family, a low-power 32-bit MCU platform built around the ARM Cortex-M3 architecture. This hierarchy places it within embedded processors, microcontrollers, and energy-efficient IoT control devices. Key features include a 32 MHz Cortex-M3 core, 32 KB of Flash, 4 KB of RAM, 53 digital I/O pins, two 16-bit timers, a 12-bit ADC, LCD support, and AES hardware security. The EFM32 low-power platform provides autonomous peripheral operation, energy-saving modes, and fast wake-up times that help reduce the time the processor remains active. The EFM32TG842F32-QFP64 combines a conventional RISC processor with highly integrated analog and timing resources. Its AES accelerator supports secure firmware and communication tasks, while its LCD and analog peripherals reduce the need for external components in compact control panels. According to the family datasheet, the platform consumes as little as 0.6 µA in Stop mode and operates at approximately 150 µA/MHz in Run mode. Typical applications include battery-powered sensor nodes, industrial condition monitoring equipment, compact human-machine interfaces, metering devices, connected low-power accessories, and portable measurement products. The 53 I/O pins allow a single controller to supervise displays, sensors, actuators, and communication interfaces without an additional I/O expander. When laying out the board, keep the 32 MHz crystal or oscillator path compact and route high-current switching nodes away from analog inputs and the Cortex-M3 supply pins. Review the pin-description table in the manufacturer datasheet when assigning board functions, and confirm startup, debug, and programming requirements before releasing the PCB layout. This page combines manufacturer specifications, package details, drop-in alternatives, parameter comparisons, and practical design guidance to support component selection, firmware planning, and PCB footprint verification for the EFM32TG842F32-QFP64.

Permintaan RFG Kontak
EFM32TG842F8-D-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32TG842F8-D-QFP64

EFM32TG842F8-D-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs

Silicon Labs EFM32TG842F8-D-QFP64 is a 32-bit ARM Cortex-M3 microcontroller operating up to 32 MHz, with 8 KB of Flash memory, 2 KB of RAM, and 53 digital I/O pins in a 64-pin TQFP package measuring 10 mm by 10 mm. Its 1.98 V to 3.8 V operating-supply range supports low-voltage embedded systems. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and communication interfaces on one device. The EFM32 Tiny Gecko family belongs to the hierarchy of 32-bit MCU, embedded processor, microcontroller, and semiconductor. It is designed for compact products that require deterministic control, flexible peripheral routing, and low-energy operation without a separate external memory bus. The device provides 2 timers with 16-bit counters, configurable peripheral I/O locations, fast wake-up behavior, and energy-saving operating modes. Its 8 KB Flash stores firmware while 2 KB of RAM supports working data and stack operations. The 53 digital I/O pins provide connections for sensors, actuators, indicators, communications, and control logic. These features make the MCU suitable for energy-sensitive monitoring, industrial control, and connected embedded equipment. The EFM32 architecture combines an ARM Cortex-M3 32-bit RISC processor with configurable peripherals and energy-management hardware. According to the manufacturer datasheet, the Cortex-M3 core can achieve as much as 1.25 Dhrystone MIPS per MHz, while a Memory Protection Unit supports up to eight memory segments. A Wake-up Interrupt Controller handles events occurring while the processor is asleep, supporting responsive operation without continuous active processing. Typical uses include low-power sensor nodes, compact industrial controllers, energy-harvesting equipment, building controls, and connected IoT terminals. The device can serve systems that repeatedly sleep between measurements, wake for a task, process peripheral data, and return to a low-power state. Its 53 I/O pins also reduce the need for an external I/O expander in moderately connected designs. PCB implementation requires careful decoupling, clock planning, and exposed-pad layout according to the manufacturer package guidance. Place the recommended input and bypass capacitors close to their corresponding supply pins, route sensitive clock and reset signals away from fast-switching nodes, and provide a continuous ground reference. Firmware selection must also account for the 8 KB Flash limit and the specific peripheral set of the chosen device variant. This page consolidates the key electrical, memory, timing, package, and lifecycle characteristics of the EFM32TG842F8-D-QFP64, compares same-family hardware options, and provides practical guidance for firmware, PCB, and sourcing decisions.

Permintaan RFG Kontak
EFM32TG842F8-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32TG842F8-QFP64

EFM32TG842F8-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs

Silicon Labs EFM32TG842F8-QFP64 is an ARM Cortex-M3 Tiny Gecko microcontroller rated up to 32 MHz, with 8 kB Flash, 2 kB RAM, and 53 digital I/O pins in a 64-TQFP 10 x 10 mm package. It operates from a 1.85 V to 3.8 V supply, making it suitable for compact, energy-sensitive embedded systems that need substantial GPIO connectivity and low-power operation. A microcontroller is a programmable system-on-chip integrating a CPU core, memory, timers, communication peripherals, and I/O into one device. The EFM32 Tiny Gecko family combines an ARM Cortex-M3 processor with low-energy design techniques, fast wake-up behavior, and energy-saving modes. This places it within the hierarchy MCU, embedded processor, semiconductor, and energy-conscious embedded control. The EFM32TG842F8-QFP64 includes 8 kB of Flash for program storage and 2 kB of SRAM for working memory. Its 53 digital I/O pins provide broad integration opportunities, while two 16-bit timers support timing, pulse-width, and periodic-control tasks. Verified distributor data also identifies the device as an LCD and AES MCU, indicating dedicated support for embedded display and security-oriented applications. The 64-TQFP package provides 64 physical pins, enabling more peripheral and signal access than the 8 kB memory footprint alone might suggest. Because pin multiplexing determines which peripheral functions can be assigned simultaneously, designers should review the pin configuration tables before fixing a board layout. The 10 x 10 mm package is larger than common QFN packages but remains practical for industrial and consumer boards requiring broad lead-based connectivity. Typical uses include low-power sensor nodes, compact industrial controllers, wearable and wellness equipment, LCD-driven user interfaces, and security-equipped embedded controls. The 32 MHz Cortex-M3 core provides more compute headroom than lower-clock general-purpose microcontrollers while the Tiny Gecko power-management features support duty-cycled operation. The principal design constraint is memory sizing: 8 kB Flash and 2 kB RAM may be sufficient for small control loops but restrictive for protocol-heavy firmware, graphical interfaces, or extensive logging. Confirm the required code and data budget, peripheral pin mapping, and voltage tolerances before committing to this MCU. This product data combines the official specification page, distributor listings, and verified cross-reference results with engineering-focused application, comparison, and design guidance. It also distinguishes confirmed drop-in alternatives from parts that cannot safely replace this exact 64-pin device.

Permintaan RFG Kontak
EFM32TG842F8-QFP64T - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32TG842F8-QFP64T

EFM32TG842F8-QFP64T - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32TG842F8-QFP64T is an ARM Cortex-M3 32-bit microcontroller operating up to 32 MHz, with 8 kB Flash memory, 2 kB RAM, 53 digital I/O pins, and a 64-pin TQFP package measuring 10 mm by 10 mm. The device is designed for energy-sensitive embedded systems that require responsive processing, low-power operation, integrated analog functions, and flexible peripheral routing. An ARM Cortex-M3 microcontroller is a 32-bit embedded processor built around the ARM instruction set and designed for control-oriented applications. The EFM32 Tiny Gecko family combines the Cortex-M3 core with autonomous peripherals, energy-saving modes, fast wake-up behavior, LCD support, AES hardware, and analog resources. Within the embedded semiconductor hierarchy, this device belongs to the microcontroller, embedded processor, and energy-efficient IoT device-control categories. Key device attributes include a maximum clock frequency of 32 MHz, 8 kB of Flash, 2 kB of RAM, 53 digital I/O pins, two 16-bit timers, AES support, LCD capability, and three operational amplifiers. A 1.85 V to 3.8 V supply range permits operation from a regulated 3 V rail or a suitable low-voltage battery arrangement, subject to the detailed power-system requirements in the manufacturer datasheet. The Tiny Gecko architecture is intended to reduce processing overhead by allowing peripherals to perform routine tasks independently of the CPU. Low-energy techniques and sleep modes are especially useful in battery-powered products where the MCU must alternate between short active intervals and long low-power intervals. The family data sheet also identifies low Stop-mode consumption and approximately 150 uA/MHz Run-mode consumption as platform characteristics, while exact operating conditions must be evaluated for the selected package and operating configuration. Typical uses include low-power sensor nodes, compact industrial monitoring equipment, connected IoT controls, small LCD instruments, security-equipped portable products, and embedded consumer devices. AES hardware can support encrypted data transfer or protected firmware workflows, while the integrated op-amps and LCD interface reduce the need for separate components in compact systems. PCB design should preserve short, quiet analog connections around the operational amplifiers and place decoupling capacitance close to the supply pins. Confirm the exact pin assignments, exposed pad requirements, and power-entry sequence in the manufacturer pinout and application information before layout release. This page combines manufacturer specifications, application guidance, and replacement analysis for faster engineering review.

Permintaan RFG Kontak
EFM32WG230F64-QFN64 - 48MHz Cortex-M4F MCU | Silicon Labs
EFM32WG230F64-QFN64

EFM32WG230F64-QFN64 - 48MHz Cortex-M4F MCU | Silicon Labs

Silicon Labs EFM32WG230F64-QFN64 is a 32-bit ARM Cortex-M4F microcontroller with a 48 MHz operating frequency, 64 KB of Flash memory, and hardware AES support. It is packaged in a 64-QFN surface-mount package measuring 9 mm by 9 mm and operates from a 1.98 V to 3.8 V supply. The part combines a Cortex-M4F processor with DSP instruction support and a floating-point unit. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one compact device. The EFM32WG230 belongs to the Wonder Gecko family, which is positioned within the hierarchy of 32-bit microcontroller, embedded processor, and energy-conscious embedded-control IC. Its combination of compute capability and low-power operating modes makes it suitable for connected, portable, and industrial systems that process data while limiting energy use. Principal features include a 48 MHz Cortex-M4F core, 64 KB Flash, and dedicated AES hardware. The DSP instruction set accelerates common digital signal-processing operations, while the floating-point unit supports real-time arithmetic without requiring software emulation. Operation across a 1.98 V to 3.8 V supply range allows integration with low-voltage digital systems, subject to the voltage and timing limits stated in the manufacturer documentation. The Wonder Gecko architecture emphasizes energy efficiency through multiple low-power operating modes and rapid transitions into active processing. These characteristics distinguish the device from general-purpose Cortex-M4 microcontrollers designed primarily for maximum processing throughput. Designers can place the part between deep-sleep operation and active control, making it useful in systems where average power consumption is more important than continuous maximum-clock performance. Typical uses include battery-operated sensor nodes, connected industrial equipment, compact control modules, and low-power edge devices. Its 48 MHz processor is suitable for protocol handling, digital filtering, state-machine control, and general embedded processing. The AES accelerator can improve the efficiency of cryptographic workloads when the application requires encrypted or authenticated data transfer. PCB design must follow the 64-QFN land pattern and preserve adequate clearance around exposed and perimeter pads. Decoupling should be placed close to the supply pins, and signal-routing and grounding decisions should be checked against the pin-description table and recommended layout guidance in the manufacturer documentation. This page combines the core device characteristics with application guidance, package considerations, and a focused replacement assessment. It helps engineers distinguish the original EFM32WG230F64-QFN64 from related Wonder Gecko devices before committing a design to a specific footprint, memory configuration, or sourcing path.

Permintaan RFG Kontak
EFM32WG232F64-QFP64 - 48MHz Cortex-M4F MCU | Silicon Labs
EFM32WG232F64-QFP64

EFM32WG232F64-QFP64 - 48MHz Cortex-M4F MCU | Silicon Labs

The Silicon Labs EFM32WG232F64-QFP64 is a 32-bit ARM Cortex-M4F microcontroller operating up to 48 MHz, with 64 KB of flash memory and AES hardware support, packaged in a 64-QFN 9x9 mm package. It combines a 48 MHz Cortex-M4F processor, DSP instruction support, a floating-point unit, and low-power peripherals for embedded control applications. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and interfaces into one device. The EFM32WG232F64-QFP64 belongs to the Wonder Gecko family and is designed for compact, low-power embedded systems. Its architecture supports real-time control, communications, sensor acquisition, and human-interface functions without requiring a separate processor and supporting digital components. Key features include a 48 MHz ARM Cortex-M4F core, full DSP instruction support, a single-precision floating-point unit, and 64 KB of flash. AES acceleration supports efficient cryptographic operations. The specified 1.98 V to 3.8 V operating-supply range accommodates low-voltage 3.3 V systems, while configurable peripheral input and output locations help designers place communication and control functions on available pins. The Cortex-M4F architecture combines a 32-bit ARM instruction set with deterministic exception handling and DSP capabilities. At clock speeds up to 48 MHz, the device provides more computational headroom than slower general-purpose microcontrollers while retaining an event-driven operating model suited to battery-operated equipment. The floating-point unit accelerates common signal-processing operations without requiring software emulation. Typical uses include industrial sensor nodes, connected measurement equipment, building controls, compact motor controllers, low-power IoT terminals, and handheld instruments. Its 64 KB flash capacity is appropriate for moderate firmware workloads, while the AES peripheral is useful in designs that require encrypted data transfer or protected firmware-related communications. Board design must still confirm memory, peripheral, and security requirements against the complete device documentation. For a new layout, place decoupling capacitors close to the supply and ground pins, route sensitive signals away from fast-switching nodes, and preserve the manufacturer’s recommended exposed-pad connection and thermal land pattern. Because the orderable marking includes QFP64 while the manufacturer listing identifies a 64-QFN 9x9 mm package, verify the physical symbol, pin table, and land pattern before fabrication rather than inferring geometry from the suffix alone. This product record combines exact manufacturer and distributor attributes, supply-voltage and memory details, package information, application guidance, and practical design considerations. It also separates confirmed characteristics from parameters that require a direct datasheet check, helping engineers plan sourcing and PCB review with fewer specification assumptions.

Permintaan RFG Kontak
EFM32WG295F256-BGA120 - 48MHz Cortex-M4 256KB Wonder Gecko | Silicon Labs
EFM32WG295F256-BGA120

EFM32WG295F256-BGA120 - 48MHz Cortex-M4 256KB Wonder Gecko | Silicon Labs

Buy EFM32WG295F256-BGA120 Silicon Labs Wonder Gecko MCU, 48 MHz Cortex-M4F, 256 KB Flash, 120-BGA. Ideal for IoT, wearables, metering. Datasheet available.

Permintaan RFG Kontak
EFM32WG330F64-QFN64 - 48MHz Cortex-M4F MCU | Silicon Labs
EFM32WG330F64-QFN64

EFM32WG330F64-QFN64 - 48MHz Cortex-M4F MCU | Silicon Labs

Silicon Labs EFM32WG330F64-QFN64 is a 32-bit ARM Cortex-M4F Wonder Gecko microcontroller operating up to 48 MHz, with 64 KB of flash memory and a 64-QFN 9 mm × 9 mm package. It accepts a 1.98 V to 3.8 V supply and combines a floating-point unit, DSP instructions, autonomous peripherals, and energy-saving modes for compact embedded systems. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and communication interfaces into one device. The EFM32 Wonder Gecko platform belongs to the broader 32-bit embedded-controller hierarchy, combining real-time processing with low-power operation. Its autonomous peripherals can perform selected tasks with limited CPU intervention, helping conserve energy in sensor, communications, and embedded-control products. The EFM32WG330F64-QFN64 operates at up to 48 MHz and includes 64 KB of flash for firmware. Its Cortex-M4F core supports the full ARM DSP instruction set and hardware floating-point arithmetic, useful for filtering, control algorithms, and digital signal processing. The family is designed to consume as little as 0.65 µA in Stop mode and 211 µA/MHz in Run mode, according to the manufacturer datasheet. Integration is a major technical advantage. On-chip analog and autonomous peripherals reduce the need for separate sensors, timers, and interface components, while dedicated hardware can continue selected operations during low-energy periods. The 1.98 V to 3.8 V operating range supports low-voltage embedded systems, although the final rail tolerance must include voltage, temperature, and transient effects. Typical uses include wireless sensor nodes, connected industrial sensors, low-power monitoring equipment, consumer controls, and compact embedded-control platforms. The same 48 MHz Cortex-M4F architecture is also suitable for DSP-oriented routines that require deterministic execution without an external digital signal processor. PCB design should preserve the manufacturer's recommended power, decoupling, clock, and exposed-pad arrangements in the 64-QFN footprint. Confirm the complete pin assignment and exposed thermal pad connection in the manufacturer datasheet before routing analog, oscillator, and high-current supply signals. This page organizes the key operating specifications, qualified same-package alternatives, application guidance, and engineering considerations into one practical selection reference. It also highlights where flash capacity, peripheral sets, lifecycle status, and software migration requirements can affect replacement decisions.

Permintaan RFG Kontak
EFM32WG332F64-QFP64 - 48MHz Cortex-M4F 64KB MCU | Silicon Labs
EFM32WG332F64-QFP64

EFM32WG332F64-QFP64 - 48MHz Cortex-M4F 64KB MCU | Silicon Labs

The Silicon Labs EFM32WG332F64-QFP64 is a 32-bit ARM Cortex-M4F Wonder Gecko microcontroller operating up to 48 MHz, with 64 KB of flash memory in a 64-QFN 9 x 9 mm package. It operates from a 1.98 V to 3.8 V supply and combines a 64-bit ARM Cortex-M4F core, USB, and hardware AES support in a compact low-power design. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, peripherals, and communication interfaces on one device. The EFM32WG332 belongs to the Wonder Gecko family of 32-bit embedded microcontrollers, combining an ARM Cortex-M4F processor with energy-conscious peripherals for connected, low-power products. Its floating-point and DSP instruction support makes it suitable for control logic that must process mixed integer, signal, and floating-point workloads. The headline configuration combines a 48 MHz Cortex-M4F core, 64 KB flash, USB connectivity, and AES security in a 64-QFN package. The compact 9 x 9 mm package supports space-constrained circuit boards while providing 64 electrical contacts. Its 1.98 V to 3.8 V operating range is appropriate for systems using a regulated 3.3 V rail or compatible lower-voltage supply architectures. The Cortex-M4F architecture provides a 32-bit processing path with single-precision floating-point and DSP instructions. This allows efficient implementation of digital control, sensor processing, communications, and protocol handling without requiring a separate digital signal processor. Hardware AES and USB support further reduce the processing burden associated with secure data transfer and USB-connected equipment. Typical applications include energy-metering and utility equipment, building-automation controllers, industrial sensor nodes, portable medical accessories, connected security products, and compact USB peripherals. The Wonder Gecko platform is particularly relevant when a design needs strong processing performance, low-power operation, and integrated connectivity in a small package. Designers should assign all 64 package pins from the manufacturer pin-description table and preserve the exposed thermal-pad connection recommended for the selected PCB land pattern. Decoupling, clock stability, USB routing, and supply sequencing should follow the device reference circuitry. Firmware development should use the supported Silicon Labs toolchain and verify peripheral assignments against the exact package variant. This page consolidates the confirmed electrical identity, package information, connectivity features, replacement analysis, comparison parameters, and practical integration guidance for engineers evaluating the EFM32WG332F64-QFP64.

Permintaan RFG Kontak
EFM32WG380F256-QFP100T - 256KB Flash ARM Cortex-M4F MCU | Silicon Labs
EFM32WG380F256-QFP100T

EFM32WG380F256-QFP100T - 256KB Flash ARM Cortex-M4F MCU | Silicon Labs

The Silicon Labs EFM32WG380F256-QFP100T is an ARM Cortex-M4F Wonder Gecko microcontroller (MCU) delivering 48 MHz core speed, 256 kB of Flash, and 32 kB of RAM in a 100-pin LQFP (14x14 mm) package. The "T" suffix designates a Tray packaging option, suitable for low-volume production and prototyping on the same PCB footprint as the tape-and-reel variant. A microcontroller is a single-chip computer containing a CPU core, on-chip memory, and a rich set of digital and analog peripherals. The Cortex-M4F class belongs to ARM's energy-efficient 32-bit processor line, adding a hardware single-precision Floating Point Unit (FPU) and full DSP instruction set on top of the Cortex-M4 core. The EFM32 Wonder Gecko family is positioned as a low-power MCU sub-class under Silicon Labs' EFM32 Gecko portfolio, intended for battery-powered and energy-harvesting products. Key features include an integrated USB 2.0 Full-Speed device controller with on-chip PHY, hardware AES-128/256 cryptographic accelerator, 12-bit ADC, and a peripheral reflex system that lets timers and GPIO events trigger peripherals autonomously without waking the CPU. The MCU offers 93 GPIO, multiple serial interfaces (USART, SPI, I2C, USB), and a low-energy timer/counter suitable for Always-On designs. Energy efficiency is the defining characteristic of the EFM32WG platform. The device consumes as little as 0.65 microamps in Stop mode with retained RAM and runs at 211 A/MHz active, with fast 2 microsecond wake-up from sleep. The autonomous peripherals and energy-saving modes let designers push most of the system into nano-ampere sleep states while keeping wake-up responsiveness intact. Typical applications include industrial sensor nodes, smart metering, building automation, USB-enabled wearables, and portable medical devices where both DSP signal conditioning and ultra-low standby current are required. When designing with this device, pay attention to the 1.8-3.8V supply range and add bulk decoupling on VDD/VDD_USB. Verify the 100-pin LQFP pinout matches your PCB land pattern; tray (T) and tape-reel (R) suffixes share the identical silicon. This page synthesizes distributor pricing, drop-in same-family variants, and AEO-Q3.4 energy-saving design notes not aggregated in the manufacturer datasheet.

Permintaan RFG Kontak
EFM32WG840F64-QFN64 - 48MHz Cortex-M4F MCU | Silicon Labs
EFM32WG840F64-QFN64

EFM32WG840F64-QFN64 - 48MHz Cortex-M4F MCU | Silicon Labs

The Silicon Labs EFM32WG840F64-QFN64 is a 32-bit ARM Cortex-M4F microcontroller operating up to 48 MHz, with 64 KB of flash memory in a 64-QFN 9 x 9 mm package. The device combines a DSP instruction set, single-precision floating-point hardware, LCD-oriented peripherals, and AES security support in the EFM32 Wonder Gecko family. Its 1.98 V to 3.8 V operating range supports low-voltage embedded systems where compactness, energy efficiency, and integrated security are important. An ARM Cortex-M4F microcontroller is a 32-bit embedded processor that combines a general-purpose instruction set with DSP acceleration and a floating-point unit. The Cortex-M4F belongs to the wider microcontroller hierarchy, alongside ARM Cortex-M0, Cortex-M0+, Cortex-M3, and Cortex-M7 processors. Silicon Labs places the EFM32WG840F64-QFN64 within the EFM32 Wonder Gecko family, using low-energy operating techniques and fast wake-up behavior for battery-powered and energy-conscious products. The device runs at 48 MHz and includes 64 KB of flash memory for firmware and constants. Its Cortex-M4F architecture supports the DSP instruction set and hardware floating-point operations, which improve performance for digital filtering, control algorithms, audio processing, and other mixed integer-and-float workloads. The integrated AES capability supports encrypted data transfer or storage without requiring a separate cryptographic accelerator. The microcontroller is designed around a low-power platform featuring energy-saving modes and rapid wake-up capability. These characteristics are particularly useful in portable instruments, sensor nodes, industrial monitoring equipment, and connected products that spend most of their operating life in a low-energy state. The manufacturer also describes backup-battery operation for maintaining system operation when the main power source drains. Typical uses include low-power sensor nodes, compact industrial controllers, medical monitoring modules, connected security devices, energy meters, and control systems with a small display interface. The LCD connection and AES support make the device especially relevant to portable products that combine a human-readable display with protected data. Its 64-QFN package also supports space-constrained board layouts while exposing a substantial peripheral set through 64 contacts. Designers should verify the exact pin assignments, exposed-pad connection, decoupling requirements, and supported operating-temperature grade against the manufacturer datasheet before layout release. Because the device combines a 48 MHz processor with external memory, display, and radio interfaces, careful decoupling, controlled return paths, and signal-integrity layout are important. The QFN thermal pad should be connected according to the package and board-stackup guidance in the datasheet. This product record combines the key device characteristics with practical application guidance, pinout considerations, and verified drop-in alternatives. It is intended to help engineers assess the Cortex-M4F, 64 KB flash, 48 MHz performance, low-power operation, AES support, and 64-QFN footprint before committing the part to an embedded design.

Permintaan RFG Kontak
EFM32WG842F64-QFP64 - 48MHz Cortex-M4F 64KB MCU | Silicon Labs
EFM32WG842F64-QFP64

EFM32WG842F64-QFP64 - 48MHz Cortex-M4F 64KB MCU | Silicon Labs

Silicon Labs EFM32WG842F64-QFP64 is a 32-bit ARM Cortex-M4F Wonder Gecko microcontroller with a 48 MHz operating frequency, 64 KB of flash memory, and a 64-TQFP package. The device is designed for low-power embedded systems that require efficient 32-bit processing, integrated cryptographic hardware, and flexible serial connectivity. A microcontroller is a semiconductor integrated circuit containing a processor core, program memory, data memory, peripherals, and I/O in one package. It belongs to the embedded-controller hierarchy: microcontroller → 32-bit MCU → ARM Cortex-M4F MCU → EFM32 Wonder Gecko. Compared with a general-purpose processor, the EFM32WG842F64-QFP64 combines deterministic peripheral control with energy-saving operating modes, making it suitable for connected control products that must operate from limited power budgets. The principal device parameters are a 48 MHz clock, 64 KB of flash program memory, and a 1.98 V to 3.8 V supply range. The Cortex-M4F core includes the full DSP instruction set and floating-point unit, according to the manufacturer documentation, while product listings identify integrated AES and LCD-related capabilities. These features support signal processing, secure communication, and human-interface applications without requiring a separate high-performance processor. Memory and peripheral density make this MCU useful in industrial equipment, building controls, sensor gateways, metering equipment, and compact consumer devices. The 64-TQFP package provides 64 accessible package leads and a 10 mm by 10 mm footprint suitable for surface-mount assembly. Its 32-bit architecture also provides more computational headroom than 8-bit or 16-bit controllers for protocol stacks, data filtering, and control-loop calculations. Power-system design should account for the 1.98 V to 3.8 V operating range and the output requirements of every attached peripheral. Decoupling capacitors should be placed close to the supply pins, while unused inputs should be connected according to the pin-description table in the manufacturer datasheet. Firmware should use the documented clock, reset, and low-power configuration sequences to maintain reliable startup behavior. This product page combines the manufacturer-level device identity with a package-focused engineering comparison, practical design guidance, and clearly identified substitution constraints. It is intended to help engineers determine whether the EFM32WG842F64-QFP64 matches an existing 64-TQFP PCB design before requesting commercial availability and lead-time confirmation.

Permintaan RFG Kontak
EFM32WG940F64-QFN64 - 48MHz Cortex-M4F MCU | Silicon Labs
EFM32WG940F64-QFN64

EFM32WG940F64-QFN64 - 48MHz Cortex-M4F MCU | Silicon Labs

The Silicon Labs EFM32WG940F64-QFN64 is a 32-bit ARM Cortex-M4F Wonder Gecko microcontroller operating up to 48 MHz, with 64 KB of flash memory and a 64-QFN 9 x 9 mm package. It includes the DSP instruction set and a floating-point unit, while its 1.98 V to 3.8 V operating supply supports low-voltage embedded systems. USB and LCD-oriented capabilities make the device suitable for connected human-interface products. A microcontroller is an integrated circuit that combines a processor core, memory, peripherals, and I/O in one package. The EFM32WG940 belongs to the Wonder Gecko family and the wider EFM32 low-power embedded-product hierarchy. Its Cortex-M4F core executes compact embedded software, while dedicated peripherals reduce the processing burden for communications, timing, data acquisition, display interaction, and general-purpose control. The primary features include a 48 MHz Cortex-M4F core, 64 KB of flash memory organized as 64K x 8, full DSP instructions, and a hardware floating-point unit. The 1.98 V to 3.8 V supply range supports both low-voltage digital systems and designs operating from a regulated 3.3 V rail. Its 64-QFN package provides a compact surface-mount footprint for space-constrained products. The floating-point unit accelerates single-precision arithmetic without software emulation, while the DSP instruction set supports signal-processing workloads. These features are valuable for local filtering, control calculations, sensor conditioning, and user-interface logic. The 48 MHz operating speed provides additional performance margin for protocol handling and coordinated peripheral activity while retaining the low-power design focus associated with the Wonder Gecko family. Typical applications include USB-connected industrial controls, compact LCD human-interface panels, environmental monitoring terminals, building-automation nodes, portable instrumentation, and connected sensor equipment. A system requiring a small display, USB connectivity, and deterministic embedded control can use the MCU to combine user feedback and communications in one processor platform. PCB implementation should account for the 64-QFN 9 x 9 mm footprint, exposed-pad thermal requirements, and the manufacturer pin and land-pattern guidance. Confirm the exact package dimensions, pin assignments, and recommended PCB library geometry in the Silicon Labs EFM32WG940 datasheet before committing a board layout. This product page combines the principal EFM32WG940F64-QFN64 specifications, verified package and supply information, a focused replacement assessment, and practical design guidance. It helps engineers evaluate CPU performance, memory capacity, peripheral requirements, package constraints, and migration risk before integrating the microcontroller into an embedded design.

Permintaan RFG Kontak
EFM32WG942F64-QFP64 - 48MHz Cortex-M4F MCU | Silicon Labs
EFM32WG942F64-QFP64

EFM32WG942F64-QFP64 - 48MHz Cortex-M4F MCU | Silicon Labs

Silicon Labs EFM32WG942F64-QFP64 is a 32-bit ARM Cortex-M4F Wonder Gecko microcontroller operating at 48 MHz, with 64 KB of flash memory and 32 KB of SRAM, in a 64-pin TQFP package. It combines a high-performance Cortex-M4F processor with low-power operation, flexible peripherals, and integrated connectivity options for compact embedded systems. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, clock circuitry, and peripherals such as GPIO, timers, serial interfaces, and analog blocks. The EFM32 Wonder Gecko family belongs to the broader hierarchy of embedded processors, 32-bit microcontrollers, and mixed-signal semiconductors designed for industrial, consumer, communications, and IoT equipment. The EFM32WG942F64-QFP64 supports operation from a 1.98 V to 3.8 V supply range and combines 48 MHz processing performance with 64 KB of flash. Its 32-bit architecture provides greater addressing capability and computational headroom than many 8-bit or 16-bit control solutions. The 64-pin TQFP package also provides access to a broad selection of GPIO and peripheral functions while supporting conventional surface-mount assembly. Silicon Labs designs the Wonder Gecko family around an ARM Cortex-M4F core with floating-point capability and energy-focused peripherals. Low-power modes are important in battery-operated equipment because they allow the processor and unused peripherals to remain idle without continuously consuming active processing power. The combination of performance, memory, and power management supports responsive control systems without requiring a separate processor for every measurement or communication function. Typical applications include industrial sensor nodes, building automation controllers, portable measurement equipment, connected accessories, low-power IoT devices, and embedded monitoring systems. The device is particularly suitable when local control, serial communications, and compact PCB integration are required within a single microcontroller rather than a combination of processor, memory, and discrete interface components. Circuit design should account for the complete pin configuration, decoupling requirements, clock strategy, boot mode, and programming interface before layout. Because the QFP64 package exposes many signals, maintain short return paths for supply and ground, place bypass capacitors close to their associated supply pins, and follow the manufacturer datasheet for the exact pin assignments and alternate functions. This product record combines the core MCU specifications, package details, verified drop-in alternatives, application guidance, and design considerations needed for initial engineering evaluation. Final firmware behavior, peripheral routing, and production programming should be validated against the current Silicon Labs datasheet and the selected board-level design.

Permintaan RFG Kontak
EFM32ZG108F16-B-QFN24 - 24MHz Cortex-M0+ MCU | Silicon Labs
EFM32ZG108F16-B-QFN24

EFM32ZG108F16-B-QFN24 - 24MHz Cortex-M0+ MCU | Silicon Labs

The Silicon Labs EFM32ZG108F16-B-QFN24 is a 24 MHz ARM Cortex-M0+ 32-bit microcontroller with 16 kB Flash, 4 kB RAM, and 17 digital I/O pins in a 24-QFN 5 x 5 mm package. It is designed for compact, energy-sensitive embedded systems that require fast wake-up, low-power operation, and integrated peripherals. The device operates from 1.98 V to 3.8 V and provides two 16-bit timers, GPIO, communications interfaces, and analog functions in a single low-power package. A microcontroller is a programmable semiconductor that integrates a processor core, memory, digital I/O, timers, and peripherals on one integrated circuit. In the power-management hierarchy, this ARM Cortex-M0+ MCU belongs to the embedded-controller class and combines general-purpose 32-bit processing with energy-conscious peripherals. The EFM32 Zero Gecko family is particularly suited to battery-operated systems, smart meters, sensors, and industrial devices that spend substantial time in low-power states. Key features include 24 MHz processing performance, 16 kB of embedded Flash, 4 kB of SRAM, 17 GPIO pins, and 2 x 16-bit timers. Silicon Labs emphasizes low-power operation, including Stop-mode consumption as low as 0.5 uA and Run-mode consumption of 114 uA/MHz. The 1.98 V to 3.8 V operating range supports low-voltage systems, while the compact 24-QFN package helps reduce board area in wearable, metering, and embedded-control products. The EFM32ZG108 architecture combines an ARM Cortex-M0+ core with configurable peripheral locations and energy-saving hardware. Its 17 I/O pins can be assigned flexibly through the device configuration mechanism, reducing the need for external multiplexing in compact designs. Two 16-bit timers support periodic events, timing measurements, and motor or waveform control. The manufacturer documentation also identifies autonomous peripheral operation as a family-level feature that can reduce CPU involvement during selected low-energy tasks. Typical applications include smart energy meters, water and gas meters, industrial sensor nodes, portable medical accessories, compact environmental monitors, and low-power IoT devices. In these systems, the MCU can manage sensor acquisition, scheduled measurements, communications, and local status indication while retaining state through multiple energy-saving states. The 24 MHz Cortex-M0+ core provides sufficient performance for protocol handling and modest control tasks without requiring a higher-complexity processor. PCB implementation requires careful attention to the exposed pad, analog and digital supply connections, and high-frequency decoupling. The EFM32ZG family documentation states that AVDD_x, VDD_DREG, and IOVDD_x pins must be connected together at the PCB level, optionally with filtering. Follow the manufacturer pin-description table and hardware-design guidance before assigning tracks, and place decoupling capacitors close to their associated supply pins. This product page combines the manufacturer specifications with engineering-focused application guidance, pin and footprint considerations, drop-in alternatives, and parameter-by-parameter comparison. These details help engineers assess fit before committing the EFM32ZG108F16-B-QFN24 to a low-power embedded design.

Permintaan RFG Kontak
EFM32ZG108F16-QFN24 - 24MHz ARM Cortex-M0+ MCU | Silicon Labs
EFM32ZG108F16-QFN24

EFM32ZG108F16-QFN24 - 24MHz ARM Cortex-M0+ MCU | Silicon Labs

The Silicon Labs EFM32ZG108F16-QFN24 is an ARM Cortex-M0+ 32-bit microcontroller operating up to 24 MHz, with 16 kB Flash memory, 4 kB RAM, 17 digital I/O pins, and two 16-bit timers in a 24-QFN (5x5 mm) package. It is designed for energy-sensitive embedded systems that require low-power operation, fast wake-up behavior, and integrated peripherals. The device supports a 1.98 V to 3.8 V supply range according to the verified product data. A microcontroller is a programmable semiconductor that combines a processor core, memory, and peripherals on one integrated circuit. The EFM32ZG family belongs to the ARM Cortex-M0+ microcontroller hierarchy, where the Cortex-M0+ core provides an efficient 32-bit architecture for embedded control, sensor, and communication products. The Zero Gecko platform emphasizes energy efficiency through low-power modes, fast wake-up times, and autonomous peripheral operation. This makes the EFM32ZG108F16-QFN24 suitable for battery-powered equipment where average energy use is more important than maximum processing throughput. The EFM32ZG108F16-QFN24 combines 16 kB of Flash with 4 kB of RAM and 17 digital I/O pins in a compact 5x5 mm QFN package. Its two 16-bit timers provide dedicated timing resources for periodic sensing, motor control, or signal generation. The integrated hardware is intended to reduce the number of external components in small embedded products while retaining the low-power characteristics associated with the Zero Gecko family. The verified manufacturer datasheet describes the EFM32ZG family as consuming as little as 0.5 microamp in Stop mode and 114 microamps per megahertz in Run mode. These figures show the family-level power behavior: the Stop-mode figure is important for duty-cycled battery systems, while the Run-mode figure helps estimate active processing energy. The device also includes low-energy techniques, fast wake-up times, energy-saving modes, autonomous peripherals, and high analog integration. Typical applications include low-power sensor nodes, compact industrial monitoring devices, battery-operated accessories, portable measurement products, and connected embedded controls. A sensor node can keep the processor stopped for most of its operating cycle, wake on an external event, acquire a measurement, process it, and return to Stop mode. For motor or timing functions, the two 16-bit timers can offload periodic operations and reduce the need for continuous software polling. When designing a board around this MCU, preserve the exposed-pad and QFN land-pattern requirements and decouple the supply pins close to the device. Confirm the exact pin multiplexing, oscillator requirements, and exposed-pad connection against the manufacturer datasheet before layout release. The QFN package is compact, so thermal performance depends on the PCB copper area and the exposed pad rather than on package size alone. This page combines verified manufacturer and distributor information, a practical comparison of same-package alternatives, and engineering guidance for low-power PCB design. It is intended to help engineers identify the correct Zero Gecko variant, plan power budgets, and move from component selection to a manufacturable 24-QFN design.

Permintaan RFG Kontak