Mikrokontroler

Produk (20.000+)

PIC12F752-I/MF - 8-Bit MCU 20MHz 1.75KB Flash 8-DFN | Microchip
PIC12F752-I/MF

PIC12F752-I/MF - 8-Bit MCU 20MHz 1.75KB Flash 8-DFN | Microchip

The Microchip Technology PIC12F752-I/MF is an 8-bit PIC microcontroller in the PIC12F family, featuring a mid-range core running at up to 20 MHz instruction rate with 1.75 KB (1K x 14) of self-read/write Flash program memory, packaged in an 8-pin DFN (3x3 mm) with exposed thermal pad. It integrates 2 high-speed analog comparators with 20 ns propagation delay, 1 Capture/Compare/PWM (CCP) module, and an internal 8 MHz oscillator that eliminates the need for an external crystal in many designs. The device targets low-pin-count cost-sensitive applications requiring on-chip analog and digital peripherals without external components. A PIC12F-series microcontroller is a member of Microchip's 8-bit mid-range architecture family, which provides a balance of low cost, low power, and adequate processing throughput for simple embedded control tasks. PIC microcontrollers use a Harvard architecture with separate program and data buses, and the 12F sub-family specifically targets applications requiring only 6-8 I/O pins. The PIC12F752 extends the 12F line by adding two fast analog comparators and a CCP module, making it suitable for power-conversion and signal-conditioning tasks where discrete analog components would otherwise be required. Key features of the PIC12F752 include 64 bytes of SRAM, 128 bytes of EEPROM, 5 channels of 10-bit ADC, a 5-bit DAC, an enhanced PWM with dead-band control, and a 4-bit comparator with programmable reference. The device operates from 2.0 V to 5.5 V across the industrial -40C to +85C range and supports In-Circuit Serial Programming (ICSP) via two pins. The internal oscillator can be tuned to 8 MHz with ±1% accuracy after calibration, allowing designs to operate without external timing components. The PIC12F752 architecture uses a 14-bit instruction word with single-cycle execution (except branches), giving roughly 5 MIPS throughput at 20 MHz. Peripherals are mapped to a banked register file accessible through dedicated SFRs, and the core supports hardware context save/restore for interrupt-driven firmware. The analog comparators can directly trigger the CCP for hardware-based control loops such as peak-current-mode power supplies or zero-crossing detectors. Typical applications include LED lighting drivers, battery chargers, switch-mode power supply control, small motor control, sensor signal conditioning, and consumer appliance user-interface controllers. The CCP and high-speed comparator combination is particularly well suited to peak-current-mode converters and synchronous rectifier timing. When designing with the PIC12F752, note that the device has only 6 general-purpose I/O pins. Designers must plan pin allocation carefully when using ICSP (which consumes two pins) and the analog peripherals simultaneously. The internal oscillator accuracy is sufficient for UART-free applications but external timing is recommended for serial communication. A decoupling capacitor of 100 nF placed within 5 mm of the VDD pin is recommended per Microchip's analog design guidelines.

Permintaan RFG Kontak
PIC12F752-I/P - 8-bit MCU, 1.75KB Flash, 8-PDIP | Microchip
PIC12F752-I/P

PIC12F752-I/P - 8-bit MCU, 1.75KB Flash, 8-PDIP | Microchip

The Microchip Technology PIC12F752-I/P is an 8-bit PIC microcontroller featuring 1.75KB (1K x 14) of Flash program memory, 64 bytes of RAM, and a 20 MHz maximum CPU speed, housed in an 8-pin PDIP (through-hole) package with industrial temperature grade (-40C to +85C). It is part of the PIC12F mid-range core family, integrating 5 general-purpose digital I/O pins, 2 high-speed analog comparators (20 ns response), 1 Capture-Compare-PWM (CCP) module, and an internal 8 MHz oscillator that delivers 5 MIPS instruction throughput. An 8-bit PIC microcontroller is a compact, Harvard-architecture RISC processor that executes one instruction per cycle (excluding branches), combining CPU core, non-volatile Flash program memory, data RAM, and configurable peripherals in a single IC. In the broader taxonomy, the PIC12F752 belongs to: microcontroller -> 8-bit MCU -> PIC microcontroller -> PIC12F mid-range family -> semiconductor. Microcontrollers are the foundation of embedded intelligence in everything from appliance controls to automotive subsystems. Key differentiating features include the 8 MHz internal oscillator (factory calibrated, eliminating external crystal cost), 2 analog comparators with 20 ns propagation delay (rare in this pin-count class), and a single 10-bit PWM/CCP channel with up to 10-bit resolution for motor or LED control. The device operates across 2.0V to 5.5V VDD, supports in-circuit serial programming (ICSP) via two pins, and includes a power-on reset / brown-out reset (BOR) block. Architecturally the PIC12F752 uses the enhanced mid-range 14-bit instruction set with 8-level hardware stack and 25 instruction opcode count. It integrates a 4-channel 10-bit ADC (with the 6-pin variant supporting up to 6 analog inputs) and a configurable 8-bit timer (Timer0/Timer1/Timer2) set, providing a balanced analog/digital peripheral mix for low-pin-count embedded designs. Typical applications include battery chargers, LED lighting drivers, small motor control (fans, pumps), appliance primary control boards, smoke detectors, and IoT sensor node MCU roles. In each case, the part's 8-pin footprint and internal oscillator reduce BOM cost while the comparators enable fast analog threshold detection. When designing with this part, verify that the 5 GPIO pins are sufficient for your application including any required UART/SPI/I2C interfaces (which are bit-banged on this device). Add a 0.1uF decoupling capacitor directly across VDD/VSS pins, kept within 5 mm trace length. For designs above 16 MHz CPU clock, the internal oscillator accuracy may require software trim or an external crystal on RA4/RA5. This page synthesizes distributor pricing, drop-in alternatives from the same PIC12F family, and practical design notes not found in the standalone manufacturer datasheet.

Permintaan RFG Kontak
PIC12F752-I/SN - 20MHz 8-Bit Flash MCU | Microchip Technology
PIC12F752-I/SN

PIC12F752-I/SN - 20MHz 8-Bit Flash MCU | Microchip Technology

The Microchip Technology PIC12F752-I/SN is an 8-bit PIC mid-range flash microcontroller rated for operation up to 20 MHz, with 1.75 KB of flash program memory organized as 1K x 14 words and 64 bytes of data RAM. The device is packaged in an 8-pin SOIC and provides six I/O lines, two high-speed analog comparators, and one Capture/Compare/PWM module. Its internal 8 MHz oscillator supports a 5 MIPS instruction rate when operating with the appropriate clock configuration. A PIC mid-range 8-bit microcontroller is a compact embedded-control device that combines a processor core, flash memory, RAM, oscillators, and dedicated peripherals on one integrated circuit. The PIC architecture belongs to the broader 8-bit microcontroller and embedded-controller hierarchy, making it useful for products requiring inexpensive deterministic control, flexible serial programming, and mixed analog and digital signal acquisition. PIC12F752 is positioned for compact control, sensing, and low-pin-count automation products. The PIC12F752-I/SN combines 1.75 KB of self-programmable flash with 64 bytes of data RAM. Two analog comparators provide 20 ns response performance, while the Capture/Compare/PWM peripheral supports timing and basic waveform-generation functions. Six I/O pins make the device useful for small control loops, sensor interfaces, and compact embedded products. The internal 8 MHz oscillator eliminates the need for an external clock in designs that do not require a different clock frequency. The mid-range PIC core executes a 35-instruction set and supports a 200 ns instruction cycle at the 20 MHz maximum operating frequency. The MCU also includes an internal oscillator, self-read/write flash capability, and the low-pin-count protections described in the PIC12F752/HV752 family datasheet. These characteristics make the device practical for applications in which program memory is sufficient for compact control firmware rather than intensive computation. Typical uses include simple motor or actuator control, temperature and industrial sensor interfaces, LED status and signage controllers, compact power-system monitoring, and small consumer products. The two comparators are especially useful for direct threshold detection, while the CCP module can reduce external timing-component requirements. The six available I/O lines should be considered carefully when designing a system that needs multiple digital signals and analog inputs. For PCB implementation, use the manufacturer's SOIC pinout and pin-description table, provide the required programming and decoupling connections, and maintain a clear signal path between the six I/O pins. The -I suffix denotes the industrial-temperature grade, while /SN identifies the SOIC package. Before production release, validate startup, oscillator behavior, programming configuration, peripheral pin assignments, and analog switching at the lowest intended supply voltage. This product page combines the manufacturer datasheet, distributor specifications, lifecycle information, and practical design guidance for evaluating the PIC12F752-I/SN in compact embedded-control designs. It also distinguishes confirmed drop-in alternatives from variants that use different package dimensions or pin arrangements, helping engineers make a PCB-compatible sourcing decision.

Permintaan RFG Kontak
PIC12F752T-I/SN - 8-Bit MCU, 1.75KB Flash, 20MHz | Microchip
PIC12F752T-I/SN

PIC12F752T-I/SN - 8-Bit MCU, 1.75KB Flash, 20MHz | Microchip

The Microchip Technology PIC12F752T-I/SN is an 8-bit PIC microcontroller based on the enhanced mid-range core, delivering up to 20MHz instruction execution from a 1.75KB (1K x 14) Flash program memory and 64 bytes of RAM, housed in an 8-pin SOIC (SN) package. It integrates a precision 20MHz internal oscillator, two high-speed analog comparators with 20ns response time, one Capture-Compare-PWM (CCP) module, and a 10-bit Analog-to-Digital Converter (ADC), positioning it as a feature-dense MCU for compact analog-intensive embedded designs. What is a PIC microcontroller? A PIC (Peripheral Interface Controller) is a family of 8/16/32-bit Harvard-architecture microcontrollers from Microchip Technology. The PIC12F752 belongs to the mid-range core family, which sits between the baseline 12-bit core and the enhanced 16-bit core. PIC microcontrollers fall under the broader category of microcontrollers (MCUs) -> embedded controllers -> semiconductors -> integrated circuits. The 8-pin PIC12F series is purpose-built for low pin-count analog and timing applications where PCB real estate is at a premium. Key features of the PIC12F752T-I/SN include 5 I/O pins (6 total I/O including MCLR/RA3), internal 8MHz oscillator with PLL support for 20MHz operation, two 20ns analog comparators ideal for power supply feedback loops and zero-crossing detection, one CCP module supporting PWM up to 10-bit resolution, 4 channels of 10-bit ADC, and an extended operating voltage range of 2.0V to 5.5V. The I in the part number designates the industrial temperature grade of -40C to +85C, and the /SN suffix identifies the 8-pin SOIC package on tape and reel (T = Tape & Reel). The PIC12F752 architecture uses a RISC instruction set with only 35 instructions to learn, simplifying firmware development. It features self-read/write Flash capability enabling in-application programming (IAP), a 4 hardware timer module stack (Timer0, Timer1, Timer2, WDT), and patented low pin-count analog IP. The integrated 8MHz internal oscillator eliminates the need for external crystal components, reducing BOM cost and PCB area. Typical applications include LED lighting drivers, DC-DC converter secondary-side control, battery chargers, motor control for small DC fans and pumps, power supply monitoring, and consumer appliance control. The two high-speed comparators make it well-suited for switch-mode power supply (SMPS) peak current-mode control loops. When designing with this MCU, allocate at least 10uF of bulk decoupling near the VDD pin and place a 100nF ceramic bypass capacitor as close to the IC as possible. The internal oscillator is factory-calibrated to within +/-1% typical accuracy, eliminating external timing components for most cost-sensitive designs. This page synthesizes distributor pricing, drop-in alternatives drawn from the same PIC12F mid-range family, and practical design notes not found in the manufacturer datasheet alone, providing engineers a single source for sourcing and replacement decisions.

Permintaan RFG Kontak
PIC12HV609-E/MS - 8-bit Flash MCU, 1.75KB, 8MSOP | Microchip
PIC12HV609-E/MS

PIC12HV609-E/MS - 8-bit Flash MCU, 1.75KB, 8MSOP | Microchip

The Microchip Technology PIC12HV609-E/MS is an 8-pin, 8-bit flash-based CMOS microcontroller from the PIC12 family, featuring 1.75 KB of Flash program memory (1K x 14), 64 bytes of RAM, and 6 I/O pins housed in an 8-MSOP (MS) package. It integrates an internal 8 MHz oscillator and supports instruction execution up to 20 MHz when driven from an external source, while the high-voltage (HV) variant accepts an unregulated supply up to the maximum VDD rating without requiring a local regulator on the input rail. What is a PIC12 microcontroller? The PIC12 family is Microchip's baseline 8-bit mid-range microcontroller line, using a RISC-style Harvard architecture with a small instruction set (typically 35 instructions), single-cycle execution at the system clock, and integrated peripherals such as comparators, timers, and a watchdog. Within the broader hierarchy, PIC12 sits below PIC16/PIC18, and PIC microcontrollers belong to the 8-bit microcontroller category of embedded semiconductors. Key features of the PIC12HV609-E/MS include 1.75 KB Flash (1K x 14 words), 64 bytes RAM, an 8 MHz internal oscillator, one 8-bit timer (TMR0), one 16-bit timer (TMR1), an enhanced mid-range core with 35 instructions and 8 hardware stack levels, 25 mA source/sink I/O drive, and a user-configurable analog comparator with hysteresis. The HV prefix means the device includes a built-in shunt regulator, allowing direct operation from 2.0 V to user-defined maximum (typical application: unregulated battery or rectified supply) without external regulation. The -E suffix denotes the -40C to +125C extended industrial temperature grade. Architecturally, the PIC12HV609 uses the same enhanced mid-range core as the standard PIC12F609, but with an internal shunt regulator front-end instead of a direct VDD pin. This internal regulator drops the high input voltage down to the core's regulated logic rail, simplifying designs that would otherwise require external zener or LDO regulators. Program memory is Flash and self-programmable under software control, supporting in-circuit serial programming (ICSP). Typical applications include battery-powered products where an unregulated stack must feed the MCU directly (HV variant specific), consumer appliances, simple sensor conditioning nodes, automotive body electronics within the -40C to +125C range, low-cost motor control loops, and any general-purpose 8-bit replacement for legacy PIC10/PIC12 designs requiring a small pin-count footprint. The device also fits remote controls, lighting controllers, and standby controllers in white goods. When designing with this part, leave adequate ground copper under the exposed MSOP pad for thermal relief, place the 0.1 uF VDD decoupling capacitor within 2-3 mm of the VDD pin, and ensure ICSP connections (PGD/PGC) are accessible for production programming. The internal shunt regulator dissipates significant power at high input voltages, so derate VDD_MAX by application voltage to stay within the thermal envelope.

Permintaan RFG Kontak
PIC12HV609-E/P - 8-bit Flash MCU, 1.75KB, 8-Pin PDIP | Microchip
PIC12HV609-E/P

PIC12HV609-E/P - 8-bit Flash MCU, 1.75KB, 8-Pin PDIP | Microchip

The Microchip PIC12HV609-E/P is an 8-bit Flash-based CMOS microcontroller in an 8-pin PDIP package, built on Microchip's mid-range PIC core with 35 instructions and 8 hardware stack levels. It integrates 1.75 KB of Flash program memory, 64 bytes of RAM, and a high-voltage shunt regulator (4 mA to 50 mA range) that allows direct operation from a high-voltage supply without a separate 5V regulator. The device runs from 2.0V to user-defined HV input with internal 4 MHz or 8 MHz oscillator options, providing flexible timing for cost-sensitive embedded designs. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, timers, I/O peripherals, and interrupt logic. Within the broader taxonomy, the PIC12HV609 belongs to the 8-bit microcontroller class -> RISC microcontroller family -> embedded controller -> semiconductor IC. The PIC12HV609 specifically sits in the PIC10/12/16 mid-range family, characterized by a 14-bit instruction word, 8-level hardware stack, and the lowest pin counts in the Microchip portfolio (6/8/14 pin). The "HV" prefix indicates the integrated shunt voltage regulator, which is the defining feature distinguishing it from the standard PIC12F609 variant. Key features include 5 general-purpose I/O pins plus 1 input-only pin with 25 mA source/sink capability for direct LED drive, individually programmable weak pull-ups, an analog comparator with programmable on-chip voltage reference, one 8-bit timer (TMR0), one 16-bit timer (TMR1), watchdog timer (WDT), enhanced power-on reset, brown-out reset (BOR), and in-circuit serial programming (ICSP). The wide operating voltage range and high-current I/O eliminate many external components typically required by competing MCUs. Architecture-wise, the device uses a Harvard architecture with separate program and data buses, allowing simultaneous instruction fetch and data access. The mid-range core executes one instruction per clock cycle (except branched instructions), delivering ~1 MIPS at 4 MHz. The integrated shunt regulator uses an external resistor network tied to the HV pin, providing regulated VDD for the core from a higher-voltage source. Typical applications include AC line-powered appliance control, LED lighting drivers, battery chargers, smart sensors, white goods control boards, and any cost-sensitive embedded application requiring a high-voltage-tolerant MCU without an external regulator. The high-voltage shunt simplifies isolated offline designs where a small switching supply feeds the HV pin directly. When designing with this part, choose the shunt resistor value based on the expected supply current (typically 4-50 mA range) and verify power dissipation in the shunt element. For battery applications where the HV input is not used, consider the PIC12F609 family instead to avoid quiescent current draw through the shunt path.

Permintaan RFG Kontak
PIC12HV609-E/SN - 8-bit 20MHz MCU 1.75KB Flash | Microchip
PIC12HV609-E/SN

PIC12HV609-E/SN - 8-bit 20MHz MCU 1.75KB Flash | Microchip

The Microchip PIC12HV609-E/SN is an 8-bit Flash-based CMOS microcontroller in the PIC12 family, integrating 1.75 KB (1K x 14) of Flash program memory, 64 bytes of RAM, and a high-voltage shunt regulator on a single 8-pin SOIC die. It runs up to 20 MHz instruction rate from a wide 2.0V–5.5V supply, with the unique HV variant capable of operating directly from a 2.5V/3.3V/5V bus without a separate regulator stage. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that combines a CPU, non-volatile program memory (Flash), working RAM, and peripheral set into one package. Within the broader embedded hierarchy, the PIC12HV609 belongs to the PIC10/12/16 mid-range core family, itself a sub-family of Microchip's 8-bit PIC microcontrollers, which in turn sit inside the embedded MCU category of integrated circuits. The "HV" prefix indicates an integrated shunt regulator, allowing direct supply from higher-voltage rails without external regulation — a useful differentiator in low-component-count designs. Key features include an internal 4/8 MHz precision oscillator, a user-configurable comparator with hysteresis, one 8-bit timer (TMR0), one 16-bit timer (TMR1), a watchdog timer (WDT), brown-out reset (BOR), power-on reset (POR), in-circuit serial programming (ICSP), and 25 mA source/sink I/O drive. Six GPIO pins are available, of which five are multiplexed with analog comparator and timer inputs. The -E suffix denotes the extended -40 °C to +125 °C industrial temperature grade, and the /SN suffix specifies the 8-SOIC (3.90 mm) package. Architecturally, the device uses Microchip's 14-bit instruction word mid-range core with 8-level hardware stack and 35 instructions, providing deterministic interrupt latency and Harvard bus separation. The high-voltage shunt regulator on the VDD pin simplifies power design in battery and bus-powered applications where a low-cost Zener-resistor supply would otherwise be required. Typical applications include low-power sensor nodes, LED driver controllers, simple state machines, automotive body electronics (AEC-Q100 qualified), battery chargers, and consumer white-goods control. The wide voltage range and integrated HV regulator make it especially attractive for cost-sensitive 5 V or 12 V appliances and for replacing discrete logic plus Zener diode combinations. When designing with this device, note that only one comparator is provided — analog-heavy designs should consider the PIC12F617 or PIC12F1501 instead. Decoupling the VDD pin with a 100 nF ceramic capacitor placed within 3 mm of the pin is essential for stable HV regulator operation. This page synthesizes distributor pricing, drop-in same-package alternatives from the PIC12 family, and practical design notes not found in the manufacturer datasheet alone.

Permintaan RFG Kontak
PIC12HV609-I/MF - 8-Pin 1.75KB Flash 8-Bit MCU | Microchip
PIC12HV609-I/MF

PIC12HV609-I/MF - 8-Pin 1.75KB Flash 8-Bit MCU | Microchip

The Microchip Technology PIC12HV609-I/MF is an 8-pin, 8-bit CMOS Flash microcontroller with integrated high-voltage shunt regulator support, offering 1.75 KB (1K x 14) of program memory, 64 bytes of RAM, and 5 configurable I/O pins in a compact 8-VDFN (DFN-8) exposed-pad package. According to Microchip product information, the device operates from 2.0 V to 5.5 V (with high-voltage shunt operation up to 4.5 V regulated output) at internal clock speeds up to 20 MHz, supported by a factory-calibrated 4 MHz / 8 MHz internal oscillator option. An 8-bit PIC microcontroller (MCU) is a small, low-power computer-on-a-chip that integrates a CPU core, Flash program memory, RAM, peripherals, and I/O on a single die. The PIC12HV609 belongs to Microchip's PIC12F family of 8-pin microcontrollers, sitting in the broader taxonomy: PIC12F -> PIC10/12/16/18 family -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The HV variant adds an internal shunt regulator suitable for direct connection to higher-voltage supplies such as 12 V or 24 V industrial rails without an external regulator. Key features include 1.75 KB Flash program memory (1K x 14 words), 64 bytes data RAM, hardware multiply, six I/O with individual direction control, one 8-bit timer (TMR0) and one 16-bit timer (TMR1), an enhanced capture/compare/PWM (ECCP) module, an analog comparator, and a 4-channel 10-bit Analog-to-Digital Converter (ADC). The internal 8 MHz oscillator with PLL can be configured for 4 MHz or 8 MHz operation, eliminating the need for external crystals in cost-sensitive designs. The PIC12HV609-I/MF uses a RISC architecture with 35 single-cycle instructions (excluding branches), a 14-bit instruction word, and a 2-stage pipeline for deterministic execution. The HV shunt regulator block enables direct connection to 2.0 V - 5.5 V sources and supports high-voltage input via external shunt components for fan-control and appliance applications. Typical applications include small fan-speed controllers, DC-DC converter housekeeping, LED lighting control, battery chargers, smoke detectors, and general-purpose 8-bit embedded control in industrial and consumer products. The 8-VDFN package suits space-constrained surface-mount designs. When designing with this device, ensure the exposed thermal pad on the 8-VDFN package is soldered to the PCB ground plane for proper thermal dissipation. The HV input pin requires external shunt resistor selection per Microchip application note AN1031 to set the regulated rail voltage. This page synthesizes distributor pricing from DigiKey, Mouser, and LCSC, drop-in alternatives within the Microchip PIC12F family, and practical design notes not aggregated in any single source.

Permintaan RFG Kontak
PIC12HV609-I/MS - 8-bit Flash MCU 1.75KB 20MHz MSOP-8 | Microchip
PIC12HV609-I/MS

PIC12HV609-I/MS - 8-bit Flash MCU 1.75KB 20MHz MSOP-8 | Microchip

The Microchip Technology PIC12HV609-I/MS is an 8-bit flash-based CMOS microcontroller from the PIC® 12F family, housed in an 8-pin MSOP package with a 20 MHz maximum CPU clock, 1.75 KB (1K x 14 words) of flash program memory, and 64 bytes of data RAM. The 'HV' suffix indicates integrated high-voltage support that allows the device to operate directly from a 2.0 V to user-defined VDD source and to handle higher-voltage I/O switching through internal shunt regulator circuitry. An 8-bit PIC microcontroller is a RISC-class single-chip MCU built around a Harvard architecture with separate program and data buses. The PIC12F/12HV family targets low-pin-count, cost-sensitive embedded applications where minimal BOM, on-chip peripherals, and nanoWatt sleep modes outweigh the need for higher MIPS. In a typical product taxonomy: PIC12HV609 -> PIC12F series -> PIC12 family -> PIC10/12/14/16/18 mid-range 8-bit MCU lineup -> Microcontroller -> Microprocessors & Controllers -> Semiconductors. Each PIC12 core executes one instruction per clock cycle (excluding branches), delivering ~5 MIPS at 20 MHz. Key differentiating features include: 1.75 KB self-programmable flash with 100K endurance cycles, 64 bytes SRAM, 128 bytes EEPROM, an internal 8 MHz oscillator (with optional 31 kHz LF oscillator), six I/O pins with individual direction control, an 8-bit timer (TMR0) with an 8-bit prescaler, a 16-bit timer (TMR1), an enhanced PWM/capture/compare (ECCP) module, a 10-bit ADC with 4 input channels, a comparator with hysteresis, and the high-voltage shunt regulator that lets the chip run from 2.0 V-5.5 V with internal regulation. The MSOP-8 package has a typical theta-JA of ~206 C/W and supports industrial -40C to +85C operation. Architecturally, the device uses a 14-bit instruction word with a 35-instruction RISC core, an 8-level hardware stack, and Microchip's nanoWatt Technology for sub-microamp sleep currents. The HV shunt regulator eliminates the need for an external regulator in 9V/12V battery or industrial bus applications, while the integrated ADC and comparator allow direct sensor conditioning without an external analog front end. Typical applications include 9V/12V battery-powered sensor nodes, AC line-voltage zero-cross detection (via high-voltage tolerant I/O), fan-speed control loops, white-goods user-interface panels, and low-cost IR remote transmitters where the 20 MHz core delivers ample headroom for RC5/SIRC protocols. The HV regulator is also valuable in industrial 24V systems where the MCU can be powered directly from the bus through a series Zener. When designing with this part, ensure the HV shunt regulator's current limit (sometimes called 'zener current') is respected: total current draw through the regulator must remain within the device's specification, otherwise internal heating may exceed the package's thermal envelope. For designs not requiring high-voltage tolerance, the PIC12F609 in the same MSOP-8 pinout is a drop-in lower-cost option.

Permintaan RFG Kontak
PIC12HV609-I/P - 8-bit Flash MCU, 1.75KB Flash, 8MHz, PDIP-8
PIC12HV609-I/P

PIC12HV609-I/P - 8-bit Flash MCU, 1.75KB Flash, 8MHz, PDIP-8

The Microchip Technology PIC12HV609-I/P is an 8-bit, 8-pin Flash-based CMOS microcontroller in the PIC12 mid-range family, supplied in a PDIP-8 (through-hole) package. It integrates 1.75 KB (1024 x 14) of self-programmable Flash program memory, 64 bytes of data RAM, and an internal 8 MHz oscillator (selectable to 4 MHz or 31 kHz LF), allowing standalone operation without an external crystal. The device supports supply voltages of 2.5 V, 3.3 V, or 5 V and is qualified for the industrial -40C to +85C operating range. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, I/O peripherals, and clock generation. The 8-bit PIC architecture uses a RISC instruction set with 35 single-word instructions and a 200 ns instruction cycle at 20 MHz, simplifying code generation in MPLAB X IDE while keeping deterministic real-time response. The PIC12 sub-family specifically targets space-constrained, low-pin-count applications such as appliance control, sensor front-ends, and battery-powered devices. Key features include four timers (Timer0, Timer1, Timer2, WDT), one enhanced Capture/Compare/PWM (ECCP) module, two analog comparators with selectable references, 6 general-purpose I/O pins, an internal shunt regulator for high-voltage operation (the "HV" suffix), Brown-Out Reset (BOR), Power-On Reset (POR), and an ICD debug interface. The PIC12HV609 is electrically identical to the PIC12F609 but adds an internal shunt regulator, allowing direct operation from supplies up to ~13.5 V without an external 5V regulator. Typical applications include LED lighting drivers, battery chargers, power-supply auxiliary controllers, smoke detectors, fan controls, and small appliance interfaces. The combination of Flash memory, internal oscillator, and high-voltage tolerance minimizes external component count. When designing with the PIC12HV609-I/P, verify that the high-voltage (HV) shunt current rating matches your supply; the internal shunt dissipates Vdd_delta * I_shunt. Always use a 0.1 uF decoupling capacitor within 5 mm of the Vdd pin and keep the ICSP clock/data traces short for reliable in-circuit programming. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
PIC12HV609-I/SN - 8-Bit 20MHz MCU, 1.75KB Flash, 8-SOIC | Microchip
PIC12HV609-I/SN

PIC12HV609-I/SN - 8-Bit 20MHz MCU, 1.75KB Flash, 8-SOIC | Microchip

The Microchip Technology PIC12HV609-I/SN is an 8-bit RISC flash microcontroller featuring the PIC12 CPU core, 1.75KB (1K x 14) of Flash program memory, 64 bytes of RAM, and a maximum operating frequency of 20MHz, housed in an 8-pin SOIC (SN) package with industrial -40C to +85C temperature grade. An 8-bit microcontroller (MCU) is a small, self-contained computer-on-a-chip integrating a CPU, program memory, data RAM, and peripherals into a single silicon die. The PIC12HV609 belongs to the mid-range PIC12 family of 8-bit PIC microcontrollers, itself part of the larger PIC microcontroller hierarchy (PIC10/12/16/18) within the broader category of microcontrollers (MCU) and embedded computing ICs. Its defining feature is the 'HV' suffix, indicating integrated high-voltage shunt regulator support allowing direct operation from 2V to user-defined higher rails via an internal shunt regulator - unusual for 8-pin flash MCUs. Key features include a 20MHz internal/external clock, 8-bit architecture with 35 single-word instructions, four channels of 10-bit ADC, one 8-bit and one 16-bit timer, an internal voltage reference, and an enhanced capture/compare/PWM module. The HV variant integrates a 5.1V-13V shunt regulator on the supply pin, allowing direct connection to rectified mains or higher DC buses without an external regulator. Brown-out reset, power-on reset, and a watchdog timer provide system reliability. Designed for fan control, LED lighting, and high-voltage sensing applications, the PIC12HV609's enhanced PWM and integrated HV shunt simplify closed-loop BLDC and brushless fan designs. The Harvard RISC architecture executes instructions in a single cycle, achieving 200ns instruction time at 20MHz. Primary uses include BLDC ceiling fan motor control, AC-line-powered LED drivers, appliance controls, and low-cost high-voltage sensor interfaces. Industrial temperature range suits automotive and appliance environments. The 8-pin SOIC footprint enables compact designs while preserving easy hand-soldering. When designing with this device, ensure the shunt regulator current budget matches the application - the internal shunt dissipates excess voltage as heat. For AC mains rectification applications, isolate the digital logic from line-voltage transients with adequate PCB clearance and TVS protection. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Permintaan RFG Kontak
PIC12HV609T-I/MD - 1.75KB Flash 8-bit MCU | Microchip | 8-DFN
PIC12HV609T-I/MD

PIC12HV609T-I/MD - 1.75KB Flash 8-bit MCU | Microchip | 8-DFN

The Microchip Technology PIC12HV609T-I/MD is an 8-bit flash-based CMOS microcontroller in the PIC12 family, offered in an 8-pin DFN-EP surface-mount package (3 x 3 mm, 0.90 mm height) and supplied on Tape and Reel. It integrates 1.75 KB of flash program memory, 64 bytes of RAM, and an internal 8 MHz oscillator, and operates across an industrial -40C to +85C temperature range at 2.5V/3.3V/5V supply rails. A PIC microcontroller (MCU) is a single-chip computer that combines a RISC CPU core, non-volatile flash program memory, RAM, and configurable peripherals around a compact die. The PIC12HV609 specifically is a low-pin-count (8-pin) member of Microchip's mid-range PIC family, optimized for cost-sensitive embedded applications where board area and BOM count matter more than raw computational throughput. It belongs to the broader hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. Key features of the PIC12HV609T-I/MD include a 20 MHz maximum CPU clock via the internal oscillator block, hardware timers (Timer0/Timer1/Timer2), a 10-bit Analog-to-Digital Converter (ADC) on selected pins, and a comparator with a programmable voltage reference. The "HV" suffix indicates an internal shunt voltage regulator that allows direct operation from higher-voltage supplies (such as 9V or 12V battery stacks) by regulating them down to the 5V internal rail. The device uses Microchip's enhanced mid-range 8-bit RISC architecture with 35 single-word instructions and a 14-bit instruction word. Two I/O pins are 5V-tolerant on most variants, supporting mixed-voltage digital interfaces. The on-chip in-circuit serial programming (ICSP) interface lets the same chip be programmed after PCB assembly using only two signal lines, eliminating programming sockets and reducing manufacturing cost. Typical applications include low-power sensor nodes, LED controllers, battery chargers, smoke detectors, and small appliance controls. The wide supply range (2.5V-5V) and built-in brown-out reset make it suitable for unregulated mains-powered or battery-powered systems. Industrial designs favor the -40C to +125C extended parts (PIC12HV609-E/MD), while the -I grade PIC12HV609T-I/MD is specified for commercial and light-industrial environments. A key design tip is that the internal shunt regulator of the "HV" variant dissipates significant power when fed from a high-voltage source. At 9V VIN and 5 mA internal draw, expect roughly 20 mW of continuous dissipation, so the exposed pad (EP) must be soldered to a copper pour for thermal relief. Layout this ground pad generously to keep junction temperature in check. This page synthesizes DigiKey distributor pricing, verified Microchip datasheet specs, same-package drop-in alternatives from Microchip's PIC12 family, and practical design guidance not found in any single distributor listing.

Permintaan RFG Kontak
PIC12HV609T-I/MF - 8-Bit Flash MCU, 1.75KB, 20MHz | Microchip
PIC12HV609T-I/MF

PIC12HV609T-I/MF - 8-Bit Flash MCU, 1.75KB, 20MHz | Microchip

The Microchip Technology PIC12HV609T-I/MF is an 8-bit, flash-based CMOS microcontroller from the PIC12 family, featuring 1.75 KB of program memory and 64 bytes of RAM in an 8-pin DFN (VSON) exposed-pad package. The 'HV' suffix denotes an integrated shunt regulator that derives the device supply directly from 2.0V-5.5V across a wide input range without a separate rail, simplifying power-tree design in low-cost systems. An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, program memory, data RAM, peripherals, and I/O on one silicon die. PIC12-series microcontrollers sit at the entry tier of Microchip's PIC architecture portfolio (8-bit PIC -> mid-range core -> microcontroller -> embedded processor -> semiconductor), targeting compact, cost-sensitive applications where 8-pin or 14-pin packages replace discrete logic and timers. The PIC12HV609T-I/MF operates at up to 20 MHz clock speed with a 4.5V absolute maximum supply and 6 I/O pins. It integrates a precision 8 MHz internal oscillator, eliminating external crystal components in many designs. The device features an enhanced mid-range 14-bit instruction set, 128 bytes of EEPROM, and a 10-bit ADC with 4 channels. Hardware peripherals include a comparator, Capture/Compare/PWM (CCP) module, and a watchdog timer, all accessible through Microchip's MPLAB X IDE toolchain. Typical applications include LED drivers, battery chargers, power-conversion controllers, sensor conditioning, and consumer appliance controls. The compact 3x3 mm DFN package and integrated shunt regulator reduce BOM cost and PCB area in space-constrained designs requiring deterministic 8-bit processing. When designing with this device, ensure the DFN-8 exposed pad is soldered to a thermal pad for proper heat dissipation, and that firmware is validated with MPLAB X IDE and XC8 compiler. Decoupling capacitors must be placed within 5 mm of the supply pin to mitigate digital switching noise. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Source: Microchip PIC12F609/615/617 and PIC12HV609/615 datasheet DS41302D.

Permintaan RFG Kontak
PIC12HV615-E/MF - 8-Bit 20MHz MCU 1.75KB Flash | Microchip
PIC12HV615-E/MF

PIC12HV615-E/MF - 8-Bit 20MHz MCU 1.75KB Flash | Microchip

The Microchip Technology PIC12HV615-E/MF is an 8-bit flash-based CMOS microcontroller from the PIC® 12F family, featuring a 20MHz maximum clock speed, 1.75KB (1K x 14) of flash program memory, and 64 bytes of data RAM, all housed in an 8-pin DFN (3x3mm) package. It operates from 2V to 5.5V, integrates a 10-bit ADC with 4 input channels, includes a built-in 8MHz internal oscillator, and offers 6 I/O pins with nanoWatt power management. The "HV" variant adds an internal shunt regulator that allows direct operation from higher-voltage supplies (up to 5V regulated internally), making it ideal for applications where a stable supply is needed without external regulation. An 8-bit microcontroller is a small computer-on-a-chip that integrates a CPU, program memory (flash/ROM), data memory (RAM), and peripherals (ADC, timers, I/O) into a single IC. The PIC12HV615 belongs to the mid-range PIC® family that uses a 14-bit instruction word and a RISC architecture, occupying a position in the taxonomy: PIC12HV615 -> PIC12F MCU family -> 8-bit PIC MCU -> PIC microcontroller -> microcontroller unit (MCU) -> embedded semiconductor. These MCUs target cost- and space-constrained designs where a full 32-bit processor would be overkill but a simple logic circuit is insufficient. Key features of the PIC12HV615-E/MF include the integrated 8MHz internal oscillator (eliminates external crystal), 10-bit ADC with 4 channels for analog signal acquisition, a 5-bit DAC for analog output, two 8-bit timers plus one 16-bit timer, an enhanced PWM module, an internal voltage reference, and nanoWatt technology for ultra-low sleep currents. The "HV" shunt regulator is the critical differentiator: it accepts inputs up to the device maximum and internally regulates to 5V, simplifying power supply design in 12V battery and unregulated supply scenarios. Typical applications include LED lighting controllers, battery chargers, sensor signal conditioning, simple motor control loops, low-cost consumer appliances, and home automation sensor nodes. The compact 3x3mm DFN package combined with only 8 pins forces tight firmware design but enables PCBs under 10mm square. Design consideration: ensure exposed pad (EP) on the DFN-8 package is soldered to the PCB ground plane for proper thermal dissipation and electrical grounding. The internal shunt regulator dissipates excess voltage as heat; size the input current budget accordingly. This page synthesizes distributor pricing, pin-compatible same-brand alternatives within the PIC12F family, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
PIC12HV615-E/MS - 8-bit 20MHz 1.75KB Flash MCU | Microchip
PIC12HV615-E/MS

PIC12HV615-E/MS - 8-bit 20MHz 1.75KB Flash MCU | Microchip

The Microchip Technology PIC12HV615-E/MS is an 8-bit flash-based CMOS microcontroller from the PIC12 family, featuring a 20 MHz instruction cycle, 1.75 KB (1K x 14) of program Flash, 64 bytes of RAM, and a high-voltage (HV) shunt regulator variant that allows direct operation from a 2V-5V supply without a conventional on-chip voltage regulator. It is housed in an 8-pin MSOP package with 6 I/O pins, and integrates a precision 4/8 MHz internal oscillator, a comparator with hysteresis, a 10-bit ADC, an 8-bit timer, and a 16-bit timer/PWM module. A PIC microcontroller (MCU) is a compact programmable processor built on a Harvard architecture where program and data memory use independent buses. Within Microchip's taxonomy, the PIC12 series belongs to the mid-range 8-bit core with 35 instructions and 8 hardware stack levels, sitting below the PIC16/PIC18 families in complexity but above baseline parts like the PIC10. This hierarchy makes the PIC12HV615 ideal for cost-sensitive, low-pin-count applications where deterministic 8-bit control is preferred over 32-bit solutions. Key features include 1.75 KB self-programmable Flash, in-circuit serial programming (ICSP) via two pins, an integrated voltage reference, comparator with user-configurable hysteresis, 4-channel 10-bit ADC with internal voltage reference, PWM output, and an on-chip HV shunt regulator that accepts up to 9V on HV pin. The MSOP-8 footprint is a small-outline plastic package measuring 3.00 mm wide, well suited for dense PCB designs. Power-down current drops below 1 uA typical, and the device operates across -40C to +125C industrial extended temperatures. Typical applications include LED lighting controllers, battery chargers, sensor signal conditioning, power supply monitoring, fan speed controllers, and small appliance controls. The high-voltage shunt regulator removes the need for an external LDO when powered from rectified mains-derived rails. The integrated ADC and comparator allow direct sensor interfacing without external signal conditioning. When designing with this part, ensure decoupling of VDD with at least a 0.1 uF ceramic capacitor placed within 5 mm of the supply pin, and reserve the ICSPDAT/ICSPCLK pins or dedicated PGM mode for in-circuit programming access. The HV shunt regulator draws excess current to ground, so thermal management of the MSOP-8 thermal pad is important at high input voltages. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the standalone manufacturer datasheet, giving engineers a faster path to BOM validation.

Permintaan RFG Kontak
PIC12HV615-E/P - 8-Bit 20MHz MCU 1.75KB Flash | Microchip
PIC12HV615-E/P

PIC12HV615-E/P - 8-Bit 20MHz MCU 1.75KB Flash | Microchip

The Microchip PIC12HV615-E/P is an 8-bit flash-based CMOS microcontroller from the PIC12 family, delivering 20 MHz instruction execution in an 8-pin PDIP through-hole package. The 'HV' suffix indicates the integrated shunt regulator (typically 5V/4V/3.3V/2V variants), allowing direct operation from a high-voltage supply (2.0V–user-defined via shunt) without an external LDO in many node configurations. An MCU (microcontroller unit) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and peripheral set on one die. Within the PIC taxonomy, this device belongs to the PIC12 mid-range baseline family, itself part of the broader 8-bit PIC microcontrollers category, then microcontrollers -> integrated circuits -> semiconductors. The 'HV' line is a low-pin-count derivative designed to remove the external regulator in cost- or size-sensitive designs. Key features include 1.75 KB (1K x 14) of self-programmable flash program memory, 64 bytes of RAM, 6 configurable I/O pins, a 20 MHz internal oscillator with software calibration, and a 10-bit ADC with up to 4 channels. The integrated shunt regulator eliminates the need for an external 78xx-style regulator when the input rail exceeds 5V, reducing BOM cost and PCB footprint in space-constrained designs. Architecturally, the PIC12HV615 uses Microchip's enhanced mid-range RISC core with 35 single-word instructions and a hardware multiplier (8x8 in one cycle). The integrated shunt is rated for input voltages up to a user-defined level (commonly 12V-15V absolute maximum, depending on variant and thermal design), enabling direct operation from battery stacks, 12V bus rails, or rectified AC sources. Typical applications include low-power sensor nodes, LED driver controllers, smoke detector interfaces, appliance user-interface boards, and battery chargers. The wide operating temperature range (-40°C to +125°C for the 'E' industrial extended grade) supports both consumer and industrial deployments. When designing with this MCU, derate the shunt regulator power dissipation with proper PCB copper area and never exceed the absolute maximum shunt input voltage; a 1kΩ to 10kΩ shunt resistor pairs with the internal pass element to set VDD. This page synthesizes distributor pricing tiers, pin-compatible same-family alternatives (PIC12F615, PIC12HV609), and practical design considerations beyond the manufacturer datasheet, including DIP footprint reuse for breadboarding and thru-hole industrial designs.

Permintaan RFG Kontak
PIC12HV615-I/MD - 8-bit 20MHz 1.75KB Flash MCU | Microchip
PIC12HV615-I/MD

PIC12HV615-I/MD - 8-bit 20MHz 1.75KB Flash MCU | Microchip

The Microchip PIC12HV615-I/MD is an 8-bit flash-based CMOS microcontroller in the PIC12 family, featuring 1.75KB (1K x 14) of Flash program memory, 64 bytes of RAM, and 6 I/O pins, housed in an 8-pin DFN (4x4 mm) surface-mount package. It operates from a 2.0V to 5.5V supply with a maximum clock speed of 20MHz, and is qualified for the industrial temperature range of -40C to +85C. An 8-bit microcontroller (MCU) is a small, self-contained computing device built around an 8-bit data path and an integrated CPU, memory, and peripherals on a single silicon die. PIC microcontrollers implement Microchip's proprietary RISC architecture, executing instructions in a single cycle (200 ns at 20MHz) from a compact 35-instruction set, balancing low power, deterministic timing, and code efficiency. PIC12-family devices sit at the low-end of the PIC hierarchy -> 8-bit PIC -> PIC microcontroller -> microcontroller -> embedded processor -> semiconductor, optimized for cost-sensitive, space-constrained applications where only a few I/O pins are needed. The PIC12HV615 integrates key differentiating features including a high-voltage shunt regulator on the VDD pin (the HV suffix), enabling direct connection to higher-voltage buses via an external Zener/resistor network without a separate LDO. It also includes an internal 8MHz oscillator (4MHz factory calibrated), 4 channels of 10-bit ADC, a comparator, and Flash program memory that supports in-circuit serial programming (ICSP). Architecturally, the PIC12HV615 uses a Harvard RISC core with separate program and data buses, allowing simultaneous instruction fetch and operand access. The wide operating range and integrated peripherals enable standalone analog and digital sensing designs without external components. The HV shunt regulator topology is distinctive: it tolerates inputs well above 5.5V (with proper external component selection), making it ideal for automotive and industrial nodes where the upstream supply is unregulated. Typical applications include LED lighting control, battery chargers, sensor signal conditioning, and automotive/industrial subsystems where board space and BOM count are critical. Compared with switching regulators + MCU combinations, the integrated HV shunt simplifies the analog front end. When designing with the PIC12HV615-I/MD, ensure the DFN-8 (MD) exposed pad is properly soldered for thermal dissipation and that the HV shunt network components are correctly sized for the target input voltage. The device is supported by Microchip's MPLAB X IDE and XC8 compiler toolchain. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, providing engineers with a single reference for sourcing, selection, and PCB layout decisions.

Permintaan RFG Kontak
PIC12HV615-I/P - 8-Bit 20MHz 1.75KB Flash MCU 8-PDIP | Microchip
PIC12HV615-I/P

PIC12HV615-I/P - 8-Bit 20MHz 1.75KB Flash MCU 8-PDIP | Microchip

The Microchip Technology PIC12HV615-I/P is an 8-bit PIC® mid-range CMOS flash microcontroller with a 20 MHz CPU and 1.75 KB (1K x 14) of program Flash memory, packaged in an 8-pin PDIP through-hole form factor. The 'HV' variant integrates an internal shunt regulator that lets the device operate directly from a high-voltage source (up to 9 V) when paired with an external Zener diode, eliminating the need for a separate 5 V regulator in many designs. The industrial temperature grade (-40 °C to +85 °C) and 6 I/O pins make it suited to compact, cost-sensitive embedded modules. The PIC12HV615 differs from the standard PIC12F615 primarily through this internal shunt regulator; otherwise the silicon (CPU core, peripherals, pinout) is shared. An 8-bit PIC microcontroller is a small, RISC-based single-chip computer built around Harvard architecture with separate program and data buses. PIC12F/HV6xx devices belong to the PIC12 family -> mid-range 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The PIC12HV615's mid-range core executes one instruction per 200 ns at 20 MHz and uses only 35 single-word instructions, which simplifies firmware development and reduces code size. The device exposes internal 4/8 MHz precision oscillators, a configurable comparator with hysteresis, an 8-bit ADC (10-bit on later rev.), PWM, and 25 mA source/sink I/O for direct LED or transistor drive. Key features include 1.75 KB Flash program memory, 64 bytes RAM, 128 bytes EEPROM, six general-purpose I/O pins, an internal 4 MHz or 8 MHz oscillator (selectable), 20 MHz max external clock, on-chip comparator and ADC, and an internal shunt regulator for high-voltage operation. Two hardware PWM channels support simple motor or LED-dimming tasks without additional peripherals. From an architecture standpoint the PIC12HV615 uses a 14-bit instruction word mid-range core, hardware stack with eight levels, and NanoWatt power management with multiple sleep modes. The internal shunt regulator replaces the conventional VDD pin, allowing direct connection to higher-voltage rails via an external series resistor and Zener reference. Code protection follows Microchip's standard low-pin-count security scheme and is protected by U.S. Patent No. 5,847,450. Typical applications include LED lighting controllers, small appliance control, battery chargers, fan/thermostat controllers, and hobby/educational embedded boards. The internal shunt regulator makes it especially attractive in mains-derived or battery-stack designs where a low-cost 5 V rail is otherwise required. When designing with the PIC12HV615-I/P, place a 1 µF decoupling capacitor directly on the VDD/VSS pins and configure the HV regulator with an appropriate external Zener and series resistor per the datasheet typical application circuit to avoid exceeding the shunt regulator's dissipation limit. This page synthesizes distributor pricing, pin-compatible same-package drop-in alternatives, and design guidance that goes beyond the manufacturer datasheet to accelerate your design-in and procurement decisions.

Permintaan RFG Kontak
PIC12HV615T-I/MD - 8-Bit 20MHz 1.75KB Flash MCU | Microchip
PIC12HV615T-I/MD

PIC12HV615T-I/MD - 8-Bit 20MHz 1.75KB Flash MCU | Microchip

The Microchip Technology PIC12HV615T-I/MD is an 8-bit, 8-pin Flash-based CMOS microcontroller built on the enhanced mid-range PIC® 12F architecture, offering 1.75 KB of Flash program memory, 64 bytes of SRAM, and 128 bytes of EEPROM in a compact 3 mm x 3 mm 8-pin DFN (MD) exposed-pad package. It operates at clock speeds up to 20 MHz and supports supply voltages of 2.5 V, 3.3 V, and 5 V, making it flexible for both battery-powered and line-powered designs. The device integrates a high-voltage (HV) shunt regulator that allows direct operation from high-impedance sources such as a 12 V rail or a solar cell array without an external regulator. A microcontroller (MCU) is a single-chip computer containing a CPU, non-volatile program memory, RAM, and programmable I/O peripherals. The PIC12HV615 belongs to the PIC12 family of 8-bit RISC microcontrollers from Microchip, which sits within the broader 8-bit microcontroller hierarchy: 8-bit MCU -> RISC microcontroller -> embedded controller -> semiconductor. The "HV" prefix denotes an integrated shunt voltage regulator, a niche feature that lets the chip self-regulate from a wide input range while the 8-pin DFN package keeps the solution footprint minimal. Key features include six general-purpose I/O pins, four 10-bit ADC channels, two 8-bit timers plus one 16-bit timer, an enhanced PWM/Capture/Compare module, an internal 8 MHz oscillator with PLL for 32 MHz operation, and a configurable 5-bit DAC. The HV shunt regulator accepts inputs above 2.5 V and tolerates voltage drops from unregulated supplies, which simplifies isolated or energy-harvesting designs. Debug is supported through the ICSP interface using Microchip's MPLAB® PICkit™ 5 in-circuit debugger. Typical applications include LED lighting controllers, sensor signal conditioning, battery chargers, and low-cost consumer appliance controls where board space is constrained. The DFN exposed-pad package enables efficient heat dissipation for the HV regulator while maintaining a 3 x 3 mm footprint suitable for hand-held and IoT-style enclosures. When selecting this part, ensure the application's input impedance allows the HV shunt regulator to source sufficient bias current (typically 5 mA minimum) - otherwise the optional PIC12F615 (without HV) is the lower-cost alternative. This page synthesizes distributor pricing, drop-in alternatives, and engineering design notes beyond the manufacturer datasheet summary, with cross-references to functionally equivalent parts in the same DFN-8 footprint.

Permintaan RFG Kontak
PIC12HV615T-I/MF - 8-bit MCU, 1.75KB Flash, 8-DFN | Microchip
PIC12HV615T-I/MF

PIC12HV615T-I/MF - 8-bit MCU, 1.75KB Flash, 8-DFN | Microchip

The Microchip Technology PIC12HV615T-I/MF is an 8-bit PIC12F-family flash microcontroller with a 20 MHz CPU clock, 1.75 KB (1K x 14 words) of flash program memory, 64 bytes of SRAM, and an integrated 8 MHz internal oscillator, packaged in an 8-pin DFN (3x3 mm) with an exposed thermal pad. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (flash), working RAM, peripherals, and I/O onto one die. The PIC12HV615 belongs to Microchip's mid-range PIC10/12/16 architecture, which uses a 14-bit instruction word and Harvard bus design optimized for deterministic, byte-oriented embedded control. In the wider taxonomy: PIC12HV615 -> PIC12F family -> 8-bit PIC MCU -> microcontroller -> embedded processing IC -> semiconductor. The "HV" prefix designates an on-chip shunt regulator that lets the device operate directly from a 2.5 V/3.3 V/5 V supply without an external regulator, simplifying power design in space-constrained nodes. Key features include 1.75 KB flash (1K x 14) self-programmable program memory, 64 bytes RAM, 6 general-purpose I/O, internal 8 MHz oscillator with PLL multiplication to 20 MHz, nanoWatt technology for ultra-low sleep current, an enhanced Capture/Compare/PWM (ECCP) module, 10-bit ADC, two comparators, and an internal shunt regulator that tolerates 4.5 V input rails. Architecturally, the PIC12HV615 uses a 14-bit RISC instruction set, an 8-level hardware stack, and a 25 ns instruction cycle (40 MIPS equivalent) at 20 MHz. The on-chip shunt regulator replaces the external LDO needed by non-HV PIC12F615, reducing BOM count and PCB area for 5 V-bus sensor and LED-driver nodes. Typical applications include compact sensor signal conditioning, LED lighting control, low-cost battery chargers, white-goods user-interface controllers, and standalone consumer appliances where small pin count, on-chip regulation, and nanoWatt sleep modes are needed. When designing, verify that the 8-pin DFN (3x3) thermal pad is properly soldered to the PCB ground plane to dissipate the shunt-regulator heat, and reserve adequate flash/RAM headroom for the chosen application stack. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
PIC12HV615T-I/MS - 8-Bit 20MHz MCU, 1.75KB Flash | Microchip
PIC12HV615T-I/MS

PIC12HV615T-I/MS - 8-Bit 20MHz MCU, 1.75KB Flash | Microchip

The Microchip Technology PIC12HV615T-I/MS is an 8-bit RISC microcontroller based on the enhanced mid-range PIC12 CPU core, delivering 20 MHz of processing throughput in a compact 8-pin MSOP (3.00 mm) package. It integrates 1.75 KB (1K x 14 words) of self-programmable Flash program memory, 64 bytes of SRAM, and 128 bytes of EEPROM, with an internal shunt regulator that allows direct operation from high-voltage rails up to 5 V without external components. The device features 6 general-purpose I/O lines, 4 channels of 10-bit Analog-to-Digital Conversion (ADC), 2 comparators, and a Capture/Compare/PWM (CCP) module. An 8-bit microcontroller (MCU) is a small single-chip computer optimized for embedded control, where a reduced instruction set (RISC) architecture executes one instruction per clock cycle. The PIC12 family represents Microchip's smallest-footprint 8-bit line, sitting below the PIC16 and PIC18 in code density and below the dsPIC/PIC32 in performance, while consuming microamp-level active current for battery and energy-harvesting applications. The HV variant adds an internal 5 V shunt regulator, allowing the device to run from unregulated supplies such as 9 V batteries or 12 V industrial rails without a separate LDO. Key features of the PIC12HV615 include 20 MHz maximum oscillator speed, instruction cycle time of 200 ns, internal 4 MHz/8 MHz/31 kHz oscillators, brown-out reset (BOR), power-on reset (POR), and an enhanced Watchdog Timer with its own on-chip RC oscillator. The integrated 10-bit ADC supports up to 4 channels with conversion rates suitable for temperature, light, and potentiometer sensing, while dual comparators enable threshold detection and zero-crossing detection without external op-amps. The internal shunt regulator with zener clamp enables direct connection to higher-voltage sources, reducing BOM cost in space-constrained designs. Typical applications include consumer appliance control, LED lighting drivers, sensor interface modules, battery chargers, and small motor control in toys or low-power tools. The wide input voltage range and integrated HV regulator make it well suited for industrial 12 V/24 V nodes that must coexist with 3.3 V logic peripherals. Designers should evaluate total power dissipation when running from high-voltage rails via the shunt regulator. Decoupling the HV pin with 0.1 uF plus bulk capacitance is recommended. The internal regulator is shunt-type - excess voltage is dropped as heat, so consider thermal layout in enclosed housings. This page synthesizes distributor pricing, parametric drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including explicit comparisons with same-package PIC12F615 and PIC12HV609 variants.

Permintaan RFG Kontak
PIC12HV615T-I/SN - 8-Bit MCU, 2KB Flash, 64B RAM, 20MHz, 8-SOIC | Microchip
PIC12HV615T-I/SN

PIC12HV615T-I/SN - 8-Bit MCU, 2KB Flash, 64B RAM, 20MHz, 8-SOIC | Microchip

The Microchip Technology PIC12HV615T-I/SN is an 8-bit PIC® microcontroller based on a RISC architecture, offering 1.75 KB (1K x 14) of FLASH program memory, 64 bytes of RAM, and 20 MHz CPU clock speed, packaged in an 8-pin SOIC. The "HV" variant integrates a high-voltage shunt regulator input (typically 2 V to user VDD) that allows direct operation from higher-voltage supplies (commonly 5 V or 12 V) without an external regulator, while the on-chip band-gap reference holds the regulated VDD for the core logic. A microcontroller (MCU) is a single-chip computer containing a processor core, non-volatile program memory, working RAM, and configurable peripherals. The PIC12HV615 belongs to the 8-bit family of microcontrollers, itself a sub-class of embedded microcontrollers, which are the smallest and most power-efficient members of the broader MCU category in the semiconductor hierarchy. 8-bit PIC MCUs use a Harvard architecture with separate program and data buses and an instruction set tuned for deterministic single-cycle execution at low clock rates. Key features of this part include a 10-bit, 4-channel Analog-to-Digital Converter (ADC), six general-purpose I/O pins, an 8-bit timer with 1:2/1:1/1:4 prescaler, a 16-bit timer/counter, one Enhanced Capture/Compare/PWM (ECCP) module, an on-chip voltage reference, and an internal 4 MHz/8 MHz oscillator selectable by configuration bits. The device draws roughly 230 µA active at 4 MHz / 2.0 V and supports industrial temperature range operation from -40 °C to +85 °C. The shunt regulator topology makes the PIC12HV615 well suited to products powered from rectified mains or 12 V rails where dropping an external linear regulator lowers BOM cost. The PIC12HV615 sits at the low end of Microchip's enhanced mid-range 8-bit line, occupying a position between baseline PIC10/12F parts and larger 14-/20-pin mid-range MCUs. Its 14-bit wide instruction word and 35-instruction RISC ISA deliver deterministic 200 ns instruction execution at 20 MHz. The 10-bit ADC is shared with the comparator input mux, allowing mixed-signal sensing in low-cost sensor nodes. Typical applications include battery charging controllers (where the shunt regulator accepts a high-voltage DC bus directly), LED drivers and signage dimming controllers, capacitive-touch front panels, low-end fan/thermostat control, simple appliance user-interface boards, and inline sensor signal conditioning modules. The 8-pin SOIC footprint also makes it a popular choice for retrofits into legacy 8-bit sockets where board space is constrained. When designing with this device, observe VDD decoupling requirements: a 0.1 µF ceramic bypass placed within 5 mm of the VDD pin and, where the shunt regulator is used, a series resistor sized so that the minimum operating current keeps the internal regulator in regulation across all load conditions. The -I temperature suffix guarantees -40 °C to +85 °C operation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
PIC12HV752-E/MF - 8-bit 20MHz MCU, 1.75KB Flash, 8-DFN | Microchip
PIC12HV752-E/MF

PIC12HV752-E/MF - 8-bit 20MHz MCU, 1.75KB Flash, 8-DFN | Microchip

The Microchip Technology PIC12HV752-E/MF is an 8-bit PIC microcontroller from the PIC12F family, featuring 1.75 KB (1K x 14) of self-read/write Flash program memory, 64 bytes of RAM, and 6 I/O pins, housed in an 8-pin DFN (3x3 mm) package. The "HV" prefix indicates a high-voltage shunt regulator variant that can operate directly from a 2V to a user-defined regulated rail derived from a higher voltage source, removing the need for an external LDO in many line-powered designs. It executes instructions at up to 5 MIPS (20 MHz internal oscillator) and integrates an 8 MHz internal oscillator with calibration. A microcontroller (MCU) is a single-chip computer that combines a CPU core, program memory, working RAM, and configurable peripherals such as timers, ADC, comparators, and communication interfaces. The PIC12HV752 sits at the low-pin-count end of the PIC mid-range core family - the smallest PIC12F devices - and trades processing throughput for compact footprint, low cost, and analog-rich integration including two high-speed analog comparators (20 ns response time) and one Capture-Compare-PWM (CCP) module. This positioning makes it a workhorse for cost-sensitive embedded control where discrete analog and a small MCU can replace a multi-chip analog front end. Key differentiating features include the 2 high-speed analog comparators with 20 ns propagation delay for peak current-mode control or fast feedback loops, a single CCP channel for PWM generation, a 10-bit ADC up to 4 channels, and an internal 8 MHz oscillator factory calibrated to +/-1 percent. The device offers 8-bit PIC mid-range core compatibility with 35 instructions, all single-cycle except branches, providing deterministic interrupt latency ideal for hard real-time loops. The PIC12HV752-E/MF is well suited to LED lighting controllers, DC-DC peak current-mode power supplies, battery chargers, fan/thermostat controllers, and any application where a small MCU drives an analog feedback loop without external analog components. Its internal HV shunt regulator allows the part to power itself from a wide DC bus (typical application circuits demonstrate 12 V to 24 V operation), simplifying isolated or off-line designs. A standard external 5.1 V shunt reference replaces a separate regulator IC, reducing BOM count and PCB area in cost-driven products. When laying out the 8-DFN package, dedicate the exposed thermal pad to a contiguous ground copper pour with at least 6 thermal vias to the inner ground plane to keep junction temperature under the 150 C maximum during continuous switching. Use a 0.1 uF decoupling capacitor within 5 mm of the VDD pin. For HV applications, place the external 5.1 V Zener/shunt reference within 10 mm of the HVIN pin to minimize parasitic inductance and ringing. This page synthesizes distributor stock and pricing, pin-compatible drop-in alternatives, and engineering design notes not collected in a single place in the manufacturer datasheet, giving procurement and design teams a faster path to a production-ready BOM.

Permintaan RFG Kontak
PIC12HV752-E/P - 8-Bit MCU, 1.75KB Flash, 20MHz, HV Shunt | Microchip
PIC12HV752-E/P

PIC12HV752-E/P - 8-Bit MCU, 1.75KB Flash, 20MHz, HV Shunt | Microchip

The Microchip PIC12HV752-E/P is an 8-bit PIC microcontroller in the PIC12F family with 1.75KB (1K x 14) Flash program memory and a maximum CPU speed of 20MHz (5 MIPS), housed in an 8-pin PDIP through-hole package. The "HV" suffix designates the integrated high-voltage shunt regulator that allows operation directly from a 2V to user-defined unregulated supply, eliminating the need for an external LDO in many low-cost designs. A microcontroller (MCU) is a single-chip computer containing a CPU, RAM, non-volatile program memory, and peripherals. The PIC12HV752 belongs to Microchip's mid-range 8-bit core family (hypernym hierarchy: PIC12F → PIC10/12/14/16/18 mid-range → 8-bit MCU → microcontroller → embedded processor → semiconductor). The 35-instruction RISC core executes most instructions in a single cycle, delivering deterministic 200ns instruction timing at 20MHz. Key features include 64 bytes of SRAM, 6 bidirectional I/O pins, a 4-channel 10-bit ADC, two high-speed analog comparators with 20ns response time, one Capture-Compare-PWM (CCP) module, and an internal 8MHz oscillator. The HV shunt regulator accepts a wide input range and regulates VDD internally, simplifying power tree design in cost-sensitive applications. The -E suffix denotes the extended industrial temperature range of -40°C to +125°C. Architecturally, the device uses a Harvard bus with separate program and data paths, an 8-level hardware stack, and an enhanced mid-range instruction set. Flash self-read/write capability supports in-application reprogramming without an external programmer, enabling field firmware updates. Typical applications include battery chargers, LED lighting controllers, smart sensor nodes, household appliance controls, and low-cost motor-control interfaces. The wide HV supply input also makes it suitable for 12V automotive accessory rails (with proper protection). When designing with this part, place a 0.1µF decoupling capacitor directly on VDD and provide a robust bypass path for the HV shunt reference. The high-speed comparators have very low propagation delay but are sensitive to PCB parasitics; keep traces short and guarded. This page synthesizes distributor pricing, parametric comparison data, and engineering design notes not found on a single manufacturer or distributor page, giving procurement and design engineers a one-stop reference for the PIC12HV752-E/P.

Permintaan RFG Kontak