Mikrokontroler

Produk (20.000+)

PIC18LF2480T-I/ML - 40MHz 8-Bit MCU, 16KB Flash, ECAN, 28-QFN | Microchip
PIC18LF2480T-I/ML

PIC18LF2480T-I/ML - 40MHz 8-Bit MCU, 16KB Flash, ECAN, 28-QFN | Microchip

The Microchip Technology PIC18LF2480T-I/ML is an 8-bit PIC18 microcontroller delivering up to 40 MIPS of CPU performance from an enhanced RISC architecture, integrating 16 KB of Flash program memory, 768 bytes of SRAM, and 256 bytes of EEPROM in a 28-pin QFN (6x6 mm) package with an exposed thermal pad. The LF prefix designates the low-voltage (2.0 V to 5.5 V VDD) variant of the PIC18F2480 family, targeting battery-powered and energy-harvesting designs where the standard F part (4.2 V to 5.5 V) cannot operate. Onboard peripherals include a 10-bit ADC with up to 8 channels, an ECAN (Enhanced Controller Area Network) module, multiple timers, USART, MSSP (SPI/I2C), and nanoWatt Technology power management for sleep currents down to the nanoampere range. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (SRAM), and configurable peripherals. Within the taxonomy of semiconductors, an MCU falls under digital logic ICs -> microcontrollers -> 8-bit microcontrollers -> PIC18 family (Microchip). The PIC18 family specifically uses a 16-bit wide instruction set with an 8-bit data path, and is widely adopted in industrial control, automotive body electronics, and CAN-bus embedded designs. Key features of the PIC18LF2480T-I/ML include 25 digital I/O pins with individual direction and weak pull-up control, an enhanced CAN (ECAN) module that supports CAN 2.0B active with three transmit buffers and two receive buffers, and nanoWatt Technology that provides multiple idle/sleep modes (Idle, Sleep, and RTCC alarm wake-up) for ultra-low standby current. The instruction set is C-optimized, allowing efficient compilation from Microchip's XC8 toolchain, and the device supports in-circuit serial programming (ICSP) plus background debug via the ICD headers. The 28-QFN (6x6) package with exposed thermal pad (EP) gives the LF2480 a small PCB footprint while still offering good thermal dissipation for sustained 40 MHz operation across the -40C to +85C industrial temperature range. The QFN EP must be soldered to the ground plane on the PCB for both thermal and electrical performance. Typical applications include CAN-bus node controllers in automotive body and chassis ECUs, industrial sensor nodes using the 10-bit ADC, low-voltage handheld instrumentation (2x AA battery-powered), CAN-to-UART gateways, and sensor-actuator nodes on factory automation networks. Compared with the PIC18F2480 (standard F variant), the LF variant extends operation down to 2.0 V and adds nanoWatt Technology, making it the better choice for battery-powered and energy-efficient designs. When designing with this MCU, note that the 28-QFN EP must be soldered to a grounded copper pad for thermal and electrical performance; omitting this connection can raise die temperature under sustained 40 MHz operation and may cause erratic ADC readings due to ground bounce. The LF variant is specified for 2.0 V to 5.5 V operation; the standard F variant requires 4.2 V to 5.5 V. This page synthesizes distributor pricing, drop-in QFN-28 alternatives, and practical ECAN/battery design notes not found in the manufacturer datasheet alone.

Permintaan RFG Kontak
PIC18LF2480T-I/SO - 8-Bit 40MHz 16KB Flash MCU w/ ECAN | Microchip
PIC18LF2480T-I/SO

PIC18LF2480T-I/SO - 8-Bit 40MHz 16KB Flash MCU w/ ECAN | Microchip

The Microchip Technology PIC18LF2480T-I/SO is an 8-bit PIC18 microcontroller featuring a 40 MHz CPU core, 16 KB (8K x 16) of enhanced Flash program memory and 768 bytes of RAM, all integrated in a 28-pin SOIC wide-body package. The device integrates an ECAN (Enhanced Controller Area Network) module, a 10-bit analog-to-digital converter, nanoWatt power management and 25 digital I/O pins, targeting low-power embedded control with on-board automotive and industrial networking. A PIC18 microcontroller belongs to the 8-bit MCU class (microcontroller unit), which integrates a CPU, non-volatile program memory, RAM, peripherals and I/O on a single die. Within the taxonomy, the PIC18F family is the high-performance tier of Microchip's 8-bit PIC line, sitting above baseline PIC10/12/16 and offering higher MIPS, larger memories and richer peripherals such as ECAN, USB and the PMP. The PIC18LF prefix denotes the low-voltage F-variant supporting operation down to 2.0 V, while standard PIC18F parts operate from 4.2 V to 5.5 V. ECAN-enabled PIC18LF2480 is commonly used as a node in CAN 2.0B networks. Key features include a maximum 40 MHz internal oscillator (10 MIPS), 16 KB Flash, 768 B RAM, 256 B EEPROM, 25 I/O, 8 channels of 10-bit ADC, two 8-bit timers and three 16-bit timers, hardware ECAN, MSSP (SPI/I2C) and an enhanced USART. The nanoWatt power-management block delivers multiple idle and sleep modes with sub-microamp sleep currents, allowing the same firmware to span battery-powered and always-on line-powered applications. Architecturally, the PIC18LF2480 uses Microchip's Harvard-based 8-bit RISC core with a 16-bit instruction word and hardware multiplier. The ECAN engine supports CAN 2.0B active with multiple transmit/receive buffers, filters and masks. The 10-bit ADC uses a dedicated successive-approximation converter with selectable acquisition time, supporting mixed-signal applications such as sensor conditioning and motor control feedback. Typical applications include CAN nodes for automotive body and chassis modules, industrial field-bus sensor and actuator interfaces, low-power battery sensor transmitters, HVAC controllers, and appliance control boards. The wide 2.0-5.5 V operating range simplifies designs that must migrate between 3.3 V and 5 V rails without re-firmware. When designing with this part, reserve adequate decoupling on VDD/AVDD pairs, route the 40 MHz oscillator traces short and symmetrical, and follow the ECAN bus-layout guideline (twisted pair, 120 ohm termination at both ends). A dedicated bootloader or ICSP header is recommended for field firmware updates. This page synthesizes distributor pricing, drop-in 28-SOIC alternatives, and practical design notes for the PIC18LF2480T-I/SO not consolidated on the manufacturer datasheet.

Permintaan RFG Kontak
PIC18LF248T-I/SO - 8-bit MCU, 16KB Flash, CAN, 28-SOIC
PIC18LF248T-I/SO

PIC18LF248T-I/SO - 8-bit MCU, 16KB Flash, CAN, 28-SOIC

The Microchip Technology PIC18LF248T-I/SO is an 8-bit PIC18F-family microcontroller featuring an integrated CAN (Controller Area Network) module, 16KB of Flash program memory, 768 bytes of SRAM, and 256 bytes of EEPROM, housed in a 28-pin SOIC (SO) package. The LF prefix indicates the low-voltage variant supporting an operating voltage range of 2.0V to 5.5V. The T suffix denotes tape-and-reel packaging, while the I suffix designates industrial temperature grade (-40C to +85C). A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data memory, peripherals, and I/O into one IC. The PIC18F family uses Microchip's enhanced 8-bit RISC architecture with a 16-bit instruction word and 8-bit data path, providing up to 10 MIPS performance at 40 MHz. PIC18LF248 variants specifically target CAN-enabled embedded applications, placing them in the broader hierarchy of microcontrollers -> 8-bit MCUs -> PIC18 family -> CAN-enabled microcontrollers -> automotive/industrial networking. Key features of the PIC18LF248T-I/SO include 23 digital I/O pins, an internal 8 MHz oscillator (with PLL support up to 40 MHz), 10-bit ADC with up to 5 channels, two analog comparators, one 8-bit and three 16-bit timers, and an ECAN module supporting CAN 2.0B active. The device also includes USART, SPI, and I2C peripherals for serial communication. Power management features include multiple sleep modes, programmable brown-out reset, and a low-power watchdog timer. The PIC18LF248 architecture combines Harvard bus separation (separate program and data memory buses) with a 32-level hardware stack and 75 instructions including hardware multiply. The ECAN module supports both standard and extended CAN frames, with configurable acceptance filters and masks for flexible message handling. The device is well-suited for real-time control applications where deterministic interrupt response and CAN bus connectivity are required. Typical applications include automotive body and chassis networks (CAN nodes), industrial CANopen or DeviceNet nodes, building automation controllers, sensor interfacing with CAN uplink, and embedded control systems requiring CAN bus communication. The 28-pin SOIC package suits through-hole and surface-mount designs in space-constrained layouts. When designing with the PIC18LF248T-I/SO, ensure decoupling capacitors are placed close to VDD/VSS pairs, and configure the ECAN module properly for your bus topology with appropriate termination. The internal oscillator can reduce BOM cost but external crystal is recommended for CAN applications requiring tight baud-rate tolerance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Permintaan RFG Kontak
PIC18LF24J10-I/ML - 8-Bit 40MHz 16KB Flash MCU 28-QFN | Microchip
PIC18LF24J10-I/ML

PIC18LF24J10-I/ML - 8-Bit 40MHz 16KB Flash MCU 28-QFN | Microchip

The Microchip Technology PIC18LF24J10-I/ML is an 8-bit PIC18 microcontroller built on a RISC architecture that runs up to 40MHz (10 MIPS) and integrates 16KB of Flash program memory with 1KB of SRAM, housed in a 28-pin QFN (6x6 mm) package with an exposed thermal pad. Key features include 16KB (8K x 16) of Flash program memory, 1024 bytes of SRAM, 256 bytes of EEPROM-like data, 16 I/O pins, an enhanced USART with LIN support, two MSSP ports supporting SPI and I2C (with address masking), a 10-bit ADC with up to 10 channels, and two analog comparators. The device operates from 2.0V to 3.6V (LF variant) and supports industrial temperature range of -40C to +85C per the I suffix. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, typically used in cost-sensitive, deterministic real-time embedded applications. Within the broader taxonomy, an MCU belongs to microcontrollers -> microcomputers -> embedded processors -> semiconductors. The PIC18 family is Microchip's mid-range 8-bit line, succeeding the PIC16 and adding an enhanced instruction set, linear (un-paged) program memory, and richer peripherals while remaining compatible with legacy designs. The PIC18LF24J10 architecture pairs a Harvard-style RISC core with on-chip Flash and a 16-bit instruction word (16-bit Flash / 8-bit data RAM). Internal oscillator options, an 8x8 hardware multiplier, and self-programmability support field updates. The LF family is optimized for low-voltage operation and is pin-compatible with the F-family PIC18F24J10, enabling a smooth upgrade path to higher speed at 5V when needed. Typical applications include low-power sensor nodes, USB HID bridges (when paired with a USB transceiver), small appliances and home automation, industrial control and instrumentation, and LIN-enabled automotive body modules. Designers frequently choose this part when deterministic 8-bit control, robust peripherals, and Microchip's MPLAB X toolchain support are required at low BOM cost. When designing with the PIC18LF24J10-I/ML, ensure VDD decoupling uses 100nF plus bulk capacitance near the EP pad, respect the 2.0V-3.6V supply range, and use Microchip's ICD 3 / ICD 4 / PICkit 4 in-circuit debuggers for development. Trade-off: the LF family trades maximum frequency for lower voltage flexibility versus the F-family.

Permintaan RFG Kontak
PIC18LF24J10-I/SO - 8-Bit 40MHz 16KB Flash MCU | Microchip
PIC18LF24J10-I/SO

PIC18LF24J10-I/SO - 8-Bit 40MHz 16KB Flash MCU | Microchip

The Microchip Technology PIC18LF24J10-I/SO is an 8-bit PIC18J RISC microcontroller running at 40 MHz with 16 KB (8K x 16) of on-chip Flash program memory, packaged in a 28-pin SOIC wide-body (SO) tube. It belongs to Microchip's low-voltage "LF" PIC18J family, designed for 2.0 V to 3.6 V operation from a single lithium-cell or regulated supply rail. What is a PIC18 microcontroller? A PIC18 is Microchip's enhanced 8-bit Harvard-architecture RISC microcontroller family, positioned above the PIC16 mid-range and below the PIC24/dsPIC 16-bit families. Within the taxonomy it belongs to microcontroller -> embedded MCU -> semiconductor IC. PIC18 devices add 16-bit wide instructions, hardware multiply, linear program memory, and C-friendly addressing, while keeping the deterministic instruction cycle that PIC parts are known for. The PIC18LF24J10 specifically targets low-voltage, high-performance designs that need rich communication peripherals (USART with LIN, two SSP ports with I2C address masking) at modest memory cost. Key features include 16 KB Flash, 1024 bytes of SRAM, 256 bytes of EEPROM, 25 digital I/O pins, 10-bit A/D converter with up to 10 channels, two analog comparators, an enhanced USART, two MSSP ports, and Microchip's nanoWatt power-management technology with multiple idle and sleep modes. The 40 MHz internal oscillator (10 MIPS throughput) eliminates an external crystal in many designs and simplifies BOM. Architecture highlights: the PIC18LF24J10 uses a 16-bit instruction word with a single-cycle ALU, a 31-level hardware stack, and a priority-enabled interrupt controller. The 10-bit ADC delivers up to 10 channels through a shared sample-and-hold, and the nanoWatt feature set (RC_RUN, SEC_RUN, SEC_IDLE, sleep) lets the device draw only a few microamps in standby, making it a strong fit for battery-powered or energy-harvesting products. Typical applications include industrial sensor interfaces, low-power handheld instruments, USB-to-UART bridges (when paired with a USB transceiver), home-automation nodes, automotive body controllers (non-safety), and small appliances requiring LIN or I2C sensor networks. The 28-pin SOIC footprint is friendly to hand-soldering and through-pin replacement on legacy boards. Design consideration: when migrating from the PIC18F24J10 to this "LF" variant, verify that VDD never exceeds 3.6 V — the F-version supports 4.2 V to 5.5 V while the LF version is restricted to 2.0 V to 3.6 V. Always place a 0.1 uF decoupling capacitor as close as practical to VDD/SS and a 10 uF bulk capacitor near the supply pin. This page synthesizes distributor pricing, drop-in pin-compatible alternatives from the same PIC18J family, and practical design notes that go beyond what is in the manufacturer datasheet.

Permintaan RFG Kontak
PIC18LF24J10-I/SP - 8-bit 40MHz 16KB Flash MCU | Microchip
PIC18LF24J10-I/SP

PIC18LF24J10-I/SP - 8-bit 40MHz 16KB Flash MCU | Microchip

The Microchip Technology PIC18LF24J10-I/SP is an 8-bit PIC18J-series RISC microcontroller running at 40 MHz with 16 KB of Flash program memory (8K x 16), housed in a 28-pin SPDIP (through-hole DIP) package. It supports a wide operating voltage range of 2.0 V to 3.6 V (LF series, low-voltage variant) and integrates 1024 bytes of SRAM, making it well suited for low-power and battery-friendly embedded designs. The 'I' suffix denotes the industrial temperature grade of -40C to +85C. A PIC microcontroller (Programmable Interface Controller) is a compact embedded processor that combines a CPU core, Flash program memory, SRAM, EEPROM, and rich on-chip peripherals (UART, SPI, I2C, ADC, timers, PWM) into a single IC. PIC18 devices sit in the upper tier of Microchip's 8-bit portfolio, featuring an enhanced instruction set, hardware multiplier, and C-friendly architecture that bridges hobby and professional embedded development. Within Microchip's hierarchy they are positioned above PIC10/12/16 baseline and mid-range devices and below the 16-bit dsPIC and 32-bit PIC32 families. The PIC18LF24J10 family delivers up to 40 MHz operation from internal oscillator, 10-bit ADC, two USART modules, MSSP (SPI/I2C), two analog comparators, and nanoWatt power management features for sleep-mode current reduction. On-chip in-circuit serial programming (ICSP) and debug interfaces shorten development cycles with Microchip's MPLAB X IDE and PICkit/Snap tools. The 'J10' silicon variant is part of the PIC18 'J' family which targets cost-sensitive, low-voltage, low-power applications with internal oscillator flexibility. Designers migrating between PIC18LF24J10, PIC18LF25J10, PIC18LF26J10, and PIC18LF27J10 (more Flash and RAM) can preserve board layout while scaling memory. Typical applications include consumer electronics, industrial control, USB peripherals (with on-chip transceiver on some variants), sensor hubs, home appliances, and low-power IoT edge nodes. The 28-pin SPDIP package is favored for through-hole prototyping, educational kits, and ruggedized industrial assemblies. For volume production, the same die is offered in SOIC-28 (SO), QFN-28 (ML), and TQFP-44 footprints. Key design consideration: route the ICSP clock/data lines to a 5-pin header with proper isolation resistors to allow in-circuit debugging without programmer interference. The LF (low-voltage) variant cannot be operated above 3.6 V - choose the PIC18F24J10 (5 V tolerant) variant for 5 V rails or mixed-voltage systems. This page combines Microchip datasheet values, distributor stock and lead time data from DigiKey/Mouser, and curated drop-in alternatives not aggregated on the manufacturer product page.

Permintaan RFG Kontak
PIC18LF24J10-I/SS - 16KB Flash 8-bit MCU, 25MHz, 28-SSOP
PIC18LF24J10-I/SS

PIC18LF24J10-I/SS - 16KB Flash 8-bit MCU, 25MHz, 28-SSOP

The Microchip Technology PIC18LF24J10-I/SS is a low-power 8-bit PIC18 microcontroller featuring 16 KB of Flash program memory, 1024 bytes of SRAM, and a 25 MHz internal oscillator, all housed in a 28-pin SSOP package. It operates across a wide 2.0V to 5.5V supply range and includes 16 I/O ports plus enhanced serial peripherals such as two synchronous serial ports (I2C with address masking) and an enhanced USART with LIN master/slave capability. The LF prefix denotes the low-voltage variant optimised for battery-powered and energy-conscious designs. A PIC18 microcontroller is a high-performance 8-bit RISC MCU built around the PIC Harvard architecture, manufactured by Microchip Technology. The PIC18LF family sits within the broader PIC18 hierarchy as a low-voltage, low-power variant that shares core peripherals with standard PIC18F parts but operates at lower core voltages. PIC18 MCUs are widely adopted in cost-sensitive embedded designs because they combine deterministic interrupt behaviour, rich peripheral integration, and the MPLAB X toolchain ecosystem into a single in-system programmable silicon platform. Key features of the PIC18LF24J10 include 1024 bytes of EEPROM data memory, two 8-bit timers plus three 16-bit timers, a 10-bit ADC with up to 13 channels, two analog comparators, an enhanced capture/compare/PWM (ECCP) module, and a master I2C/SPI interface. The Flash memory supports self-programming and ICSP (In-Circuit Serial Programming) via the MPLAB Snap, PICkit, or ICD debuggers. The device also integrates a nanoWatt XLP (eXtreme Low Power) feature set with multiple idle, sleep, and deep-sleep modes for ultra-low standby current. The PIC18LF24J10 architecture uses a 16-bit instruction word with an 8-bit data path, an internal 31-level hardware stack, and a 25 MHz oscillator block that yields 10 MIPS throughput. Its wide voltage range and brown-out reset (BOR) circuitry allow direct Li-ion battery operation or USB-powered applications where voltage rails are unregulated. The enhanced USART supports RS-232, RS-485, and LIN 1.3 protocols without external transceivers in LIN slave mode, simplifying automotive body-electronics and industrial sensor-bus designs. Typical applications include USB-to-UART bridges, sensor signal conditioning nodes, low-power wireless sensor hubs, HVAC thermostat controllers, automotive body controllers (RKE, lighting, mirror), battery-powered metering devices, and small appliance control boards. The combination of large Flash, on-chip EEPROM, and dual serial ports makes the LF24J10 well suited to designs that need both storage for calibration constants and protocol translation in a single chip. When designing with the PIC18LF24J10, ensure decoupling capacitors (100 nF ceramic plus 10 uF bulk) are placed within 5 mm of the VDD and AVSS pins. The MCLR reset pin should be tied to VDD through a 10 kohm pull-up unless external reset control is required, and the ICSP clock/data lines must be reserved in the PCB layout for in-circuit programming access. This page consolidates real-time distributor pricing from DigiKey and Mouser, validated drop-in Microchip alternatives from the same PIC18LF J10 family, and practical design notes that are not duplicated in the manufacturer datasheet summary, helping procurement and design engineers accelerate component selection.

Permintaan RFG Kontak
PIC18LF24J10T-I/ML - 8-bit 40MHz 16KB Flash MCU 28-QFN | Microchip
PIC18LF24J10T-I/ML

PIC18LF24J10T-I/ML - 8-bit 40MHz 16KB Flash MCU 28-QFN | Microchip

The Microchip Technology PIC18LF24J10T-I/ML is an 8-bit PIC18J-series microcontroller with a 40 MHz core speed and 16 KB (8K x 16) of Flash program memory, housed in a 28-pin QFN (ML) 6x6 mm package. It operates from 2.0 V to 3.6 V and is targeted at low-voltage, low-power embedded designs that need strong serial connectivity. A PIC microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), working memory (RAM), and peripheral interfaces into one package. The PIC18 family sits in the middle of Microchip's 8-bit line, using an enhanced RISC architecture that executes one instruction per clock cycle (four in most), giving deterministic timing that is valuable for real-time control, sensor reading, and protocol bit-banging. The PIC18J sub-series is specifically designed for full-speed USB and high-throughput serial designs running at 3 V rails. Key features of the PIC18LF24J10 include 1024 bytes of RAM, hardware USB 2.0 full-speed with on-chip transceiver, two enhanced USARTs (one with LIN master/slave capability), two MSSP ports supporting SPI and I2C with address masking, a 10-bit ADC with up to 10 channels, and nanoWatt power management for sleep currents below 1 uA. The integrated USB peripheral removes the need for an external transceiver, reducing BOM cost and board area. The PIC18LF24J10 architecture uses a 16-bit modified Harvard structure: separate code and data paths, a hardware multiply, and a 31-level-deep stack. The on-chip regulator allows single-supply 3.3 V operation while preserving the speed advantage of 40 MHz, and the nanoWatt technology provides multiple power-managed modes (Idle, Sleep, and deep Sleep with RTCC) for battery-powered nodes. Typical applications include USB peripherals (HID class devices, CDC serial bridges, mass storage), sensor hubs with I2C/SPI expansion, low-cost industrial controllers, and consumer devices such as gaming peripherals, remote controls, and home-automation endpoints. The wide 2.0 V-3.6 V operating range and low-power modes also make it suitable for battery-powered handheld instruments. When designing with this part, verify that the application does not require the wider 5 V PIC18F24J10 variant - the LF letter indicates the 3.3 V-only core. Plan board layout for the QFN thermal pad, which must be soldered to a continuous ground plane for both electrical performance and thermal dissipation. This page synthesizes distributor pricing, drop-in alternatives drawn from the same PIC18J family, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
PIC18LF24J10T-I/SO - 16KB Flash 8-bit MCU, 28-SOIC | Microchip
PIC18LF24J10T-I/SO

PIC18LF24J10T-I/SO - 16KB Flash 8-bit MCU, 28-SOIC | Microchip

The Microchip Technology PIC18LF24J10T-I/SO is an 8-bit PIC18J-series microcontroller featuring 16 KB of Flash program memory, 1024 bytes of SRAM, and a 40 MHz internal oscillator, housed in a 28-pin SOIC wide-body package. The 'LF' prefix indicates the low-voltage 'F' process variant, supporting an operating voltage range of 2.0 V to 3.6 V, which is optimized for battery-powered and energy-harvesting designs. The 'T' suffix denotes a tape-and-reel packaging orientation, while 'I' signifies the industrial temperature grade of -40 C to +85 C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile and non-volatile memory, peripherals, and I/O onto one IC. The PIC18 family uses Microchip's enhanced RISC architecture and is positioned in the broader product taxonomy as: microcontroller -> 8-bit MCU -> PIC18 family -> low-voltage 'LF' sub-family. PIC18 LF devices incorporate nanoWatt technology for power-managed operation, allowing the designer to balance active processing throughput against deep-sleep standby current. Key features of the PIC18LF24J10 include 16 KB (8K x 16 words) of self-programmable Flash, 1024 bytes of data SRAM, 256 bytes of EEPROM, two 8-bit timers and three 16-bit timers, two analog comparators, a 10-bit ADC with up to 10 channels, two enhanced USART modules, two MSSP (SPI/I2C) ports, and a charge time measurement unit (CTMU) for capacitive touch sensing. The 40 MHz maximum CPU clock delivers up to 10 MIPS of throughput. Architecturally, the device uses a 16-bit instruction word with an 8-bit data path, two addressable register banks, and a hardware multiplier. The instruction pipeline and 31-level stack support C-compiled firmware. The CTMU peripheral enables mTouch capacitive touch interfaces with no external components beyond the sensing pad, while the nanoWatt power-management unit offers idle, sleep, and deep-sleep modes with current draw in the microamp range. Typical applications include low-power remote sensor nodes, USB-to-UART bridges, capacitive touch user interfaces, HVAC control panels, and small-format consumer appliances. The 28-SOIC wide-body package simplifies hand-soldering and rework for prototypes and low-volume products. When designing with this MCU, ensure decoupling follows the datasheet's 100 nF + bulk capacitor recommendation and that the MCLR reset pin has the proper 10 kohm pull-up. The CTMU calibration sequence must be run after each wake-up from deep sleep for accurate touch readings. This page consolidates distributor pricing, validated drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

Permintaan RFG Kontak
PIC18LF24J10T-I/SS - 40MHz 8-bit MCU 16KB Flash SSOP-28
PIC18LF24J10T-I/SS

PIC18LF24J10T-I/SS - 40MHz 8-bit MCU 16KB Flash SSOP-28

The Microchip Technology PIC18LF24J10T-I/SS is an 8-bit PIC18 microcontroller built on a RISC core and offered in a 28-pin SSOP package with Tape and Reel packaging. The device integrates 16KB of Flash program memory (8K x 16 words), 1KB of RAM, and runs up to 40MHz with an instruction-cycle time of 100ns. The "LF" prefix designates the low-voltage variant supporting 2.0V to 3.6V operation optimized for battery-powered and portable designs. What is a PIC18 microcontroller? The PIC18 family is Microchip's 8-bit enhanced Harvard-architecture RISC microcontroller line, belonging to the broader category of microcontrollers -> microprocessors -> embedded processors -> semiconductors. PIC18 parts add 16-bit-wide instructions, an 8x8 hardware multiplier, and a richer peripheral set compared with baseline PIC16 parts, making them suited to mid-complexity embedded control tasks. Microchip is the global leader in 8-bit MCU shipments, and PIC18 devices are widely used in industrial, consumer, and automotive body-electronics applications. Key features include a 10-bit ADC with up to 10 input channels, two analog comparators, two CCP (Capture/Compare/PWM) modules, five timers, an EUSART, and an MSSP (Master Synchronous Serial Port) configurable for SPI or I2C. The device also exposes up to 21 general-purpose I/O lines and integrates the nanoWatt power-management block with multiple Idle and Sleep modes for low-power applications. In-circuit debugging via ICD/ICSP is supported directly on the production PCB. Typical applications include low-power sensor nodes, USB HID peripherals (with external interface), battery-powered handheld instrumentation, and industrial control modules operating from a 3.3V rail. The wide operating voltage range and rich peripheral mix make it a common drop-in for designs that need deterministic 8-bit performance without the cost of a 32-bit MCU. When designing with this part, confirm the target board rail falls between 2.0V and 3.6V (the LF variant is not 5V tolerant - use PIC18F24J10 for 5V rails). Decouple VDD with a 100nF ceramic plus 10uF bulk capacitor placed within 5mm of the pins. For low-power designs, switch to RC_IDLE or Sleep during idle windows to draw single-digit microamp currents. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including a curated comparison against same-family Microchip PIC18F/LF parts and third-party equivalents sourced from verified cross-reference data.

Permintaan RFG Kontak
PIC18LF24J11-I/ML - 16KB Flash 8-bit XLP MCU 28-QFN | Microchip
PIC18LF24J11-I/ML

PIC18LF24J11-I/ML - 16KB Flash 8-bit XLP MCU 28-QFN | Microchip

The Microchip Technology PIC18LF24J11-I/ML is a low-voltage 8-bit PIC microcontroller from the PIC18 J-series family with nanoWatt XLP (eXtreme Low Power) technology, delivering 16 KB Flash and 4 KB RAM in a 28-pin QFN (6x6) package. It operates up to 48 MHz internal clock (12 MIPS), supports 2.0 V to 3.6 V supply, and integrates a 10-bit ADC plus multiple serial interfaces. What is an 8-bit PIC microcontroller? An MCU (microcontroller unit) is a single-chip computer integrating CPU, program memory (Flash), data memory (RAM), and peripherals. The PIC18 family is Microchip's high-performance 8-bit architecture, with the J-series adding nanoWatt XLP technology for deep-sleep currents under 100 nA. The LF prefix denotes the low-voltage (2.0-3.6 V) variant, while F variants operate 2.0-3.6 V at higher performance levels. Key features include 16 KB self-programmable Flash, 4 KB SRAM, 256 B EEPROM, two Enhanced USART, two MSSP (I2C/SPI), two comparators, a 10-bit ADC with up to 10 channels, and nanoWatt XLP power-saving modes. The 28-QFN (6x6 mm) package provides a compact surface-mount footprint with an exposed thermal pad. Typical applications include portable medical devices, low-power sensor nodes, USB peripherals (via external transceiver), industrial control, and battery-powered consumer products. The 48 MHz core at 3.3 V achieves 12 MIPS, fast enough for USB stacks and motor control loops. Designers should connect the exposed pad to ground for thermal dissipation, place a 0.1 uF decoupling capacitor adjacent to each VDD pin, and use the ICSP interface for programming. The LF variant is preferred for battery applications where 5 V tolerance is not required.

Permintaan RFG Kontak
PIC18LF24J11-I/SP - 8-Bit 48MHz 16KB Flash XLP MCU | Microchip
PIC18LF24J11-I/SP

PIC18LF24J11-I/SP - 8-Bit 48MHz 16KB Flash XLP MCU | Microchip

The Microchip Technology PIC18LF24J11-I/SP is an 8-bit PIC18J-series microcontroller featuring 16KB of Flash program memory, 48MHz maximum clock speed, and ultra-low-power XLP (eXtreme Low Power) technology, housed in a 28-pin SPDIP (SP) through-hole package. The 'LF' prefix designates the 2.5V/3.3V low-voltage variant optimized for battery-powered and energy-harvesting designs, while the 'I' suffix denotes the industrial -40C to +85C operating temperature range. The device integrates a 10-bit ADC, multiple communication peripherals (I2C, SPI, UART/USART), and brown-out detect/reset, POR, PWM, and WDT peripherals. A microcontroller (MCU) is a single-chip computer containing a processor core, program memory, data memory, and integrated peripherals. The PIC18 family uses Microchip's enhanced RISC architecture with a Harvard-style memory layout, separating program (Flash) and data (RAM) buses for predictable instruction execution. Within Microchip's taxonomy, the PIC18LF24J11 sits at the intersection of 8-bit MCU -> Flash MCU -> nanoWatt XLP -> PIC18J-series, giving engineers a balance of code density, peripheral flexibility, and sub-microamp sleep current. The 'J' series specifically targets cost-sensitive applications requiring deep-sleep current as low as 20nA typical, making it ideal for always-on sensor nodes. Key features include 16KB (8K x 16) Flash program memory, 3.68KB data RAM, 16 programmable I/O pins, and Peripheral Pin Select (PPS) for flexible signal routing. The 48MHz internal oscillator (equivalent to 12 MIPS throughput) eliminates external crystal requirements in many designs, while the 10-bit ADC with up to 10 channels supports direct sensor interfacing. Deep-sleep current of approximately 20nA extends battery life in dormant IoT endpoints, and the on-chip 2.5V/3.3V LDO regulator allows direct connection to a single Li-ion cell or two AA cells. Architecturally, the PIC18LF24J11 uses a 16-bit instruction word optimized for C-compiled code density, with 31-level hardware stack and interrupt-priority arbitration. The nanoWatt XLP feature set includes multiple low-power modes (Run, Idle, Sleep, Deep Sleep), enabling dynamic power scaling based on application workload. JTAG/ICSP debugging is supported through standard 2-wire or 4-wire interfaces. Typical applications include battery-powered sensor nodes, IoT edge devices, low-energy wireless sensor hubs, portable medical monitors, remote controls, energy harvesting systems, consumer electronics with sleep-dominant duty cycles, and industrial control modules requiring extended battery life. The 28-pin SPDIP package supports hand-soldering and breadboard prototyping, which suits engineers transitioning from development to small-batch production. When designing with this device, choose the LF variant for sub-3.3V operation; switch to the standard F variant (e.g. PIC18F24J11-I/SP) for 3.3V-only or 5V-tolerant applications. Maintain VDD decoupling within 5mm of the supply pin (100nF plus 10uF bulk) and respect the absolute maximum VDD of 3.6V for LF parts to avoid latch-up. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, including a curated comparison against same-family SPDIP variants and a 28-pin cross-reference matrix.

Permintaan RFG Kontak
PIC18LF24J11-I/SS - 8-bit 48MHz 16KB Flash MCU | Microchip
PIC18LF24J11-I/SS

PIC18LF24J11-I/SS - 8-bit 48MHz 16KB Flash MCU | Microchip

The Microchip Technology PIC18LF24J11-I/SS is an 8-bit PIC18 microcontroller with 16 KB Flash, 3.8 KB SRAM, and 48 MHz operation in a 28-pin SSOP package, designed for nanoWatt XLP extreme-low-power applications. It integrates a 10-bit ADC, USB 2.0 full-speed, multiple serial interfaces, and the Peripheral Pin Select (PPS) feature set that defines the PIC18 J-series family. What is an 8-bit PIC microcontroller? An 8-bit microcontroller is a single-chip computer that processes data 8 bits at a time and integrates CPU, Flash, RAM, peripherals, and I/O on one die. The PIC18 LF family (the LF prefix denotes the wide-voltage 2.0V-3.6V nanoWatt XLP variant) sits within Microchip's PIC18 architecture taxonomy: 8-bit PIC -> PIC18 -> PIC18 J-series -> PIC18F/LF24J11 sub-family. Compared with 32-bit ARM Cortex-M cores, a PIC18 trades raw MIPS for deterministic latency, ultra-low sleep current, and a mature MPLAB X toolchain backed by thousands of code examples. Key features of the PIC18LF24J11-I/SS include 16 KB of self-programmable Flash memory (8K x 16 words), 3.8 KB SRAM, deep-sleep current down to a few nanoamps typical, and the Peripheral Pin Select (PPS) module that remaps digital peripherals to any remappable I/O pin, simplifying PCB routing and BOM reuse across family variants. The architecture is built on an enhanced Harvard RISC core with a hardware multiplier, an 8-bit data path, and 16-bit instructions, achieving approximately 12 MIPS at 48 MHz. The integrated 10-bit ADC supports up to 13 input channels, while USB 2.0 full-speed with integrated transceiver enables HID, CDC, and proprietary USB device classes without external PHYs. Typical applications include battery-powered medical sensors, USB HID peripherals, industrial sensor nodes, and portable consumer devices that benefit from nanoWatt XLP standby current. The 28-pin SSOP footprint suits compact designs where board area is constrained. When designing with this part, configure the PPS registers during initialization to map peripherals to desired I/O pins, choose the deep-sleep mode for battery-life optimization, and reserve the I/O budget for the planned USB, UART, and ADC channels during PCB layout. Verify ECCN and licensing rules if used in end products with cryptography co-processors or secure boot modules. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers a faster path from selection to prototype.

Permintaan RFG Kontak
PIC18LF24J11T-I/ML - 8-Bit 48MHz XLP 16KB Flash MCU | Microchip
PIC18LF24J11T-I/ML

PIC18LF24J11T-I/ML - 8-Bit 48MHz XLP 16KB Flash MCU | Microchip

The Microchip Technology PIC18LF24J11T-I/ML is an 8-bit PIC18F XLP nanoWatt microcontroller with a 48 MHz maximum CPU clock, 16 KB (8K x 16) of Flash program memory, and 4 KB of RAM, housed in a 28-pin QFN (6x6 mm) package with exposed pad. The 'LF' prefix designates the 2.0V-3.6V low-voltage variant, while the 'T' suffix denotes Tape & Reel packaging and 'I' indicates the industrial -40C to +85C operating temperature range. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O on a single die. The PIC18 family is Microchip's 8-bit RISC architecture, sitting within the broader category of embedded microcontrollers, and is widely used in cost-sensitive, low-power, mixed-signal applications. The PIC18LF24J11 belongs to the PIC18 J-series, which adds Peripheral Pin Select (PPS) for flexible signal routing and nanoWatt XLP technology for ultra-low sleep currents, enabling battery-powered designs that run for years on a single cell. Key features include 12 MIPS peak performance, hardware multipliers, a 10-bit ADC with up to 13 channels, two analog comparators, two UART/USART modules, two I2C and two SPI interfaces, four 16-bit timers, and a deep-sleep mode drawing as little as 20 nA. The 28-QFN (6x6) package with exposed thermal pad provides good thermal dissipation in a compact 6 mm x 6 mm footprint suitable for space-constrained designs. Architecturally, the device uses a modified Harvard core with separate program and data buses, allowing instruction fetch and data access in the same cycle. The Peripheral Pin Select feature allows most digital peripherals to be remapped to any digital I/O pin at runtime, decoupling the PCB layout from the firmware's peripheral choices and dramatically simplifying board design. Typical applications include battery-powered sensor nodes, USB-to-UART bridges, low-cost consumer electronics, industrial control modules, and home appliances. The wide peripheral set also makes the device suitable for small human-machine interface (HMI) panels and motor-control companion logic. When designing with this part, place a 100 nF decoupling capacitor as close as possible to the VDD pin and a 10 uF bulk capacitor on the main supply rail. Configure unused I/O as outputs low to minimize power consumption, and leverage the deep-sleep mode with the on-board RTCC for wake-up timing on battery-operated nodes. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
PIC18LF24J11T-I/SO - 16KB Flash 8-bit MCU 28-SOIC | Microchip
PIC18LF24J11T-I/SO

PIC18LF24J11T-I/SO - 16KB Flash 8-bit MCU 28-SOIC | Microchip

The Microchip Technology PIC18LF24J11T-I/SO is an 8-bit PIC microcontroller with 16KB Flash and 4KB RAM in a 28-pin SOIC (7.50mm width) package, operating at up to 48MHz and 12 MIPS. As part of the PIC18 J-series, it features the nanoWatt XLP (eXtreme Low Power) technology platform and supports an operating voltage range of 2.0V to 3.6V, targeting low-power and battery-sensitive embedded systems. An 8-bit microcontroller (MCU) is a single-chip computer containing a CPU, Flash program memory, RAM data memory, and integrated peripherals such as ADC, timers, and communication interfaces. The PIC18 family uses a RISC-based Harvard architecture with a 16-bit instruction word and 8-bit data path, falling within the broader hierarchy of microcontroller -> embedded processor -> semiconductor IC. The 18J sub-family adds a 2.5V internal regulator rail and nanoWatt XLP power management for sleep currents below 100 nA typical. Key features of the PIC18LF24J11 include 16KB (8K x 16) self-programmable Flash, 4KB SRAM, 256B EEPROM-style data storage, an integrated 10-channel 10-bit ADC, two analog comparators, two USART, SPI, I2C, and two CCP/ECCP modules. The device also provides up to 21 digital I/O lines, four timers, and a 16-bit wide instruction path for compact C-code generation. The PIC18LF24J11 uses the enhanced mid-range core with hardware multiply, 32-level stack, and an internal 31 kHz to 8 MHz RC oscillator with PLL. nanoWatt XLP modes include Sleep, Idle, and Doze, allowing the core current to drop to <100 nA in RTCC-based Sleep with full RAM retention. Typical applications include battery-powered sensor nodes, wearables, remote controls, smart meters, USB HID/Human Interface Devices, and low-power industrial controllers. The wide supply range down to 2.0V supports single-cell lithium or two-AA battery designs, while the high 48MHz performance enables real-time control loops. When designing with the PIC18LF24J11T-I/SO, verify the SOIC-28 (0.295" / 7.50mm wide) footprint against your PCB library, as Microchip ships the same silicon in SOIC-28, QFN-28 (ML), and SPDIP-28 (SP) packages. Use MPLAB X IDE with the XC8 compiler and the PICkit 4 or Snap programmer for development. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
PIC18LF24J50-I/SP - 8-bit USB MCU 16KB Flash 28-SPDIP | Microchip
PIC18LF24J50-I/SP

PIC18LF24J50-I/SP - 8-bit USB MCU 16KB Flash 28-SPDIP | Microchip

The Microchip Technology PIC18LF24J50-I/SP is a low-power, high-performance 8-bit PIC18 microcontroller with integrated full-speed USB 2.0 (12 Mbps), 16 KB of Flash program memory, 4 KB of RAM, and an enhanced instruction set, housed in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. The LF suffix indicates the low-voltage variant supporting 2.0V to 5.5V operation, while the J50 family adds deep-sleep nanoWatt XLP power management that drops quiescent current to the microamp range for battery-powered designs. The core runs up to 48 MHz internal clock (12 MIPS) with hardware multiplier, 16-bit data path, and C compiler-friendly orthogonal architecture. The integrated USB 2.0 Full-Speed transceiver with on-chip pull-up resistors eliminates external PHY components for HID, CDC, mass-storage, and vendor-class device designs. The microcontroller also includes a 10-bit ADC up to 250 ksps, multiple PWM modules, comparators, and the standard PIC18 peripheral set. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, RAM, and configurable I/O peripherals. Within the broader taxonomy, the PIC18LF24J50-I/SP belongs to the 8-bit MCU category -> RISC microcontroller -> embedded controller -> semiconductor IC. The "LF" voltage class supports 2.0V-3.6V core operation natively while remaining 5.5V tolerant on digital I/O, bridging coin-cell and Li-ion battery designs with 5V-tolerant sensors and actuators without level translators. The "J" series designation refers to the enhanced peripheral set including the on-chip USB engine and deep-sleep XLP modes, while the "50" suffix denotes the USB 2.0 Full-Speed capable variant in the family. Key features include hardware Real-Time Clock Calendar (RTCC) with timestamps, 2 KB EEPROM emulation in Flash, Master Synchronous Serial Port (MSSP) supporting SPI and I2C, two Enhanced USART modules, charge time measurement unit (CTMU) for capacitive touch and mA-range current measurement, and configurable logic cells. The device supports self-programming via ICSP (In-Circuit Serial Programming) and runs the same MPLAB X IDE / XC8 toolchain as every other PIC18 part, simplifying firmware reuse across product lines. Typical applications include USB HID peripherals (keyboards, mice, custom input devices), CDC virtual COM ports, low-power sensor nodes, capacitive touch interfaces, battery-powered instrumentation, and industrial control nodes. The 5V-tolerant digital I/O makes the part directly compatible with 5V sensors without external level shifters. Trade-off consideration: at full 48 MHz the LF core requires the upper end of its 2.0V-3.6V rail, while deep-sleep operation preserves nanoamp quiescent current but disables USB - power profiles must be budgeted carefully for USB-suspended battery applications.

Permintaan RFG Kontak
PIC18LF24K22-E/SO - 16KB Flash, 48MHz XLP 8-bit MCU | Microchip
PIC18LF24K22-E/SO

PIC18LF24K22-E/SO - 16KB Flash, 48MHz XLP 8-bit MCU | Microchip

The Microchip Technology PIC18LF24K22-E/SO is a 28-pin, 8-bit PIC18 microcontroller built on the nanoWatt eXtreme Low Power (XLP) technology platform, providing up to 16KB of Flash program memory and 768 bytes of RAM in a wide SOIC package. It runs at up to 48MHz internal clock speed and supports an operating voltage range of 1.8V to 3.6V, making it well suited for low-power and battery-operated designs. The device integrates 256 bytes of EEPROM data memory and offers rich peripheral integration for mixed-signal embedded applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and programmable I/O peripherals on one silicon die. The PIC18 family is Microchip's high-performance 8-bit RISC architecture family, featuring a modified Harvard bus, 16-bit opcodes, and an instruction pipeline that allows most instructions to execute in a single cycle. Within the PIC18 K-line portfolio, the LF sub-family emphasizes low-voltage and battery-aware operation, and the PIC18LF24K22 in particular targets applications where sleep-mode nanosecond quiescent current is critical. Key differentiating features include the nanoWatt XLP deep sleep mode with current consumption down to a few nanoamps, integrated mTouch capacitive touch peripherals, multiple Enhanced USART, MSSP (SPI/I2C) ports, and a 12-bit A/D converter with up to 17 channels. The device also offers two analog comparators, a hardware RTCC, and the standard PIC18 CTMU charge-time measurement unit for precise time-of-flight or capacitive touch sensing. The wide SOIC package gives 28 pins of I/O and supports surface-mount assembly on standard 300-mil wide SOIC-28 land patterns. Architecturally, the PIC18LF24K22 uses a 16-bit modified Harvard RISC core with 31-level hardware stack, deterministic interrupt latency, and a vectored interrupt controller. The Flash memory is self-programmable under software control, allowing boot-loader or in-application firmware updates. The XLP power-management block includes ultra-low-power wake-up sources, on-board voltage regulator, and configurable sleep/wake states managed through the PCL, T0CON, and WDTCON registers. Typical applications include portable consumer electronics, battery-powered wireless sensor nodes, capacitive touch user interfaces, motor control for low-power BLDC and stepper drivers, HVAC thermostat controllers, and medical monitoring peripherals where extended battery life is essential. The -40C to +125C operating range and low-power design also suit automotive body electronics and industrial sensor front-ends. When designing with this part, observe the 1.8V minimum VDD for Flash programming, place a 100nF decoupling capacitor adjacent to each power pin, and follow Microchip's recommended layout for the analog and oscillator pins to avoid noise coupling into the ADC. The MSSP pins share I/O ports, so firmware must configure the correct PPS mapping for SPI vs I2C operation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
PIC18LF24K22-E/SS - 16KB Flash 8-bit MCU | Microchip | SSOP-28
PIC18LF24K22-E/SS

PIC18LF24K22-E/SS - 16KB Flash 8-bit MCU | Microchip | SSOP-28

The Microchip Technology PIC18LF24K22-E/SS is a 28-pin, low-power, high-performance 8-bit CMOS flash microcontroller in the PIC18LF XLP family with 16KB (8K x 16) of program Flash, 768 bytes of RAM, and 256 bytes of EEPROM, packaged in a 28-SSOP (0.209 inch / 5.30 mm body width). An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), data memory (RAM), EEPROM, and a set of peripherals such as timers, ADC, comparators, and communication interfaces onto one die. The PIC18LF family uses a modified Harvard RISC architecture that executes most instructions in one instruction cycle and reaches up to 16 MIPS throughput; the LF prefix indicates a wide operating voltage range that supports low-voltage (LF) operation, which makes the part suitable for battery-powered applications. Key features include a 48 MHz maximum oscillator input with a 16 MIPS core, nanoWatt XLP extreme-low-power technology for sleep currents in the nanoamp range, an on-chip 10-bit ADC with up to 17 channels, multiple Enhanced USART, MSSP (I2C/SPI), and capture/compare/PWM peripherals. The 256-byte EEPROM supports endurance of up to 1,000,000 erase/write cycles per Microchip datasheet characterization. The PIC18LF24K22-E/SS uses Microchip's nanoWatt XLP technology that delivers typical sleep currents below 100 nA with retention and features such as ultra-low-power wake-up, system clock gating, and peripheral disable. The wide 1.8V to 3.6V VDD range combined with internal oscillator choices enables battery- or energy-harvesting designs that previously required an external oscillator. Typical applications include low-battery sensor nodes, portable consumer devices, industrial control panels, USB HID peripherals, and home-automation or IoT endpoints. The combination of XLP sleep current, ADC, PWM, and a rich mix of serial interfaces makes it a flexible general-purpose 8-bit controller for both mains- and battery-powered products. When designing with this device, ensure that the configured system clock (HS, XT, EC, internal LF-INTOSC) matches the selected VDD range and that the MCLR pin is properly biased (POR) for current voltage. Use ICSP programming on dedicated PGD/PGC pairs to retain the device in-circuit during firmware updates. This page synthesizes distributor pricing, drop-in alternatives within the PIC18LF K22 family, and practical design notes that complement, but are not a substitute for, the manufacturer datasheet.

Permintaan RFG Kontak
PIC18LF24K22-I/ML - 16KB Flash 8-bit XLP MCU | Microchip
PIC18LF24K22-I/ML

PIC18LF24K22-I/ML - 16KB Flash 8-bit XLP MCU | Microchip

The Microchip Technology PIC18LF24K22-I/ML is an 8-bit PIC microcontroller in the nanoWatt XLP family with 16 KB (8K x 16) of Flash program memory, 768 bytes of RAM, and 256 bytes of EEPROM, housed in a 28-pin QFN (6 x 6 mm) package with an exposed thermal pad. It is the low-voltage (LF) variant of the PIC18F24K22 family, qualified for 1.8V to 3.6V operation, and executes instructions at up to 64 MHz (16 MIPS) from an internal oscillator block. The device integrates 25 analog-capable I/O pins, multiple communication peripherals (UART, SPI, I2C), a 10-bit ADC with up to 17 channels, comparators, and the eXtreme Low Power (XLP) sleep modes that draw currents in the nanoamp range, enabling multi-year battery life in always-on applications. A PIC18 microcontroller is an 8-bit Harvard-architecture MCU built around an enhanced RISC core with hardware multiplier, prioritized interrupts, and a peripheral set optimized for mixed-signal embedded designs. The PIC18 family sits above the baseline PIC10/12/16 families in Microchip's portfolio, targeting applications that require more memory, more peripherals, and C-compilable code while retaining the deterministic instruction set of the classic PIC architecture. Within the power-management IC hierarchy, the PIC18LFxxK22 series specifically targets low-voltage, low-power products where battery life and standby current dominate the design. Key features of the PIC18LF24K22 include 16 KB self-write Flash, 768 bytes SRAM, 256 bytes EEPROM, an internal 16 MHz oscillator (selectable up to 64 MHz via PLL), 10-bit ADC with computation, up to 5 PWM modules, three 8/16-bit timer/counters, two comparators, two Enhanced USART, two MSSP (SPI/I2C), and an ICD/ICSP debug interface accessible through two I/O pins. The QFN-28 (ML) package exposes the die thermal pad for improved θJA in compact designs. Typical applications include portable medical and wellness wearables, sensor nodes for IoT building automation, remote controls and consumer HMI, industrial battery-backed instrumentation, and low-power RF transmitter front-ends. The XLP nanoWatt features make the LF24K22 especially well suited to products that spend most of their lives in Sleep mode and wake briefly for measurement or communication. When designing, ensure the device remains within the 1.8V-3.6V LF supply window; substituting the PIC18F24K22 (F variant) allows operation up to 5.5V on the identical QFN-28 footprint. This page synthesizes Microchip datasheet specifications, current distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in a single manufacturer resource.

Permintaan RFG Kontak
PIC18LF24K22-I/MV - 8-bit XLP MCU 16KB Flash 28-UQFN | Microchip
PIC18LF24K22-I/MV

PIC18LF24K22-I/MV - 8-bit XLP MCU 16KB Flash 28-UQFN | Microchip

The Microchip Technology PIC18LF24K22-I/MV is an 8-bit PIC18LF microcontroller with nanoWatt XLP technology, featuring 16KB (8K x 16) of Flash program memory, 768 bytes of RAM, and a 64MHz CPU core, housed in a compact 28-pin UQFN (4x4 mm) package with industrial temperature grade (-40C to +85C). The 'LF' prefix denotes the low-voltage variant supporting operation from 1.8V to 3.6V, while the standard 'F' PIC18F24K22 operates from 2.3V to 5.5V. A microcontroller (MCU) is a single-chip computer containing a CPU, program memory (Flash), data memory (RAM), and programmable peripherals. The PIC18 family sits in Microchip's 8-bit hierarchy: PIC10/12/16/18 -> 8-bit MCU -> microcontroller -> embedded computing IC -> semiconductor. The 'LF' subfamily specifically targets ultra-low-power applications through nanoWatt XLP technology, enabling sleep currents in the nanoamp range. Key features include 16KB Flash self-programmable memory, 256 bytes of EEPROM, 10-bit ADC up to 17 channels, multiple PWM modules, EUSART, MSSP (SPI/I2C), and ultra-low-power sleep modes. The integrated 16MHz internal oscillator eliminates external crystals in many designs, while the 28-pin UQFN package provides compact 4x4 mm footprint with exposed thermal pad suitable for space-constrained applications. CIP (Core Independent Peripherals) reduce CPU overhead by handling tasks autonomously in hardware. The PIC18LF24K22 architecture uses an enhanced Harvard RISC core with 49 instructions and hardware multiplier, executing most instructions in a single cycle for predictable deterministic performance. CIP features like CLC, PPS, and NCO enable complex signal routing without CPU intervention, making it suitable for real-time sensor processing and motor control loops. Typical applications include low-power IoT sensor nodes, battery-powered medical devices, industrial control modules, consumer electronics HMI, USB peripherals, and automotive body electronics. The wide peripheral set and low-power modes also suit remote controls, smart metering, and wearable health monitoring. The industrial -40C to +85C temperature range supports harsh environment deployment. When designing with this device, configure the PPS (Peripheral Pin Select) module early to avoid pin conflicts. Use the internal 16MHz HFINTOSC to save BOM cost and board space, but verify timing margins against your application. Review the PIC18(L)F24K22 datasheet for current consumption tables under different clock and sleep configurations before finalizing power budgets. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone. The 28-UQFN (4x4) footprint is shared with the standard PIC18F24K22-I/MV and the tape-and-reel variant PIC18LF24K22T-I/MV, enabling layout reuse across the LF/F families.

Permintaan RFG Kontak
PIC18LF24K22-I/SO - 8-bit 64MHz 16KB Flash XLP MCU | Microchip
PIC18LF24K22-I/SO

PIC18LF24K22-I/SO - 8-bit 64MHz 16KB Flash XLP MCU | Microchip

The Microchip Technology PIC18LF24K22-I/SO is an 8-bit PIC18 microcontroller featuring nanoWatt XLP (eXtreme Low Power) technology, 16KB of Flash program memory, and a 64 MHz CPU core, offered in an industrial-grade 28-pin SOIC wide-body package. The "LF" prefix denotes the low-voltage F-version (1.8V-3.6V operation), while the "I/" suffix denotes the industrial operating temperature range (-40C to +85C) and the SOIC-28 wide-body 7.50 mm surface-mount package. A microcontroller is a single-chip computer that integrates a CPU core, volatile and non-volatile memory, programmable I/O peripherals, and dedicated hardware blocks (timers, ADC, communication peripherals) into one IC. The PIC18 family sits in Microchip's 8-bit MCU lineup with an enhanced RISC architecture and 16-bit-wide instruction words; the "LF24K22" series extends the family with XLP ultra-low-power modes, larger RAM, more peripherals, and a faster 64 MHz internal oscillator pipeline compared with the earlier K20 generation. Key features of the PIC18LF24K22 include 16KB (8K x 16 words) self-programmable Flash, 768 bytes of RAM, 256 bytes of EEPROM, a 10-bit ADC (with up to 17 channels), three CCP/ECCP modules, two USART (enhanced) modules, two MSSP (I2C/SPI) modules, and 25 general-purpose I/O pins. The device supports 1.8V to 3.6V single-supply operation with nanoWatt XLP Idle, Sleep, and deep-sleep modes that drop current consumption into the nanoampere range - critical for battery-powered and energy-harvesting designs. The architecture combines a high-performance 16-bit Harvard bus, hardware multiplier, C-compiler-friendly memory map, and on-chip debug via ICD. The 64 MHz oscillator drives a four-clock-per-instruction pipeline, delivering up to 16 MIPS throughput. The device also integrates a mTouch capacitive-touch sensing peripheral and a CTMU module for advanced touch interfaces. Typical applications include battery-powered wireless sensor nodes, low-power IoT endpoints, portable medical instrumentation, remote controls, e-metering / smart thermostats, and consumer products requiring USB-less general-purpose 8-bit control. The wide SOIC-28 footprint simplifies hand-soldering and rework during prototyping. When designing with this part, ensure decoupling with 100 nF ceramic capacitors placed within 5 mm of VDD/VSS pairs, and configure the CONFIG registers to enable the lowest-power Sleep mode compatible with the application's wake-up latency budget. Avoid leaving floating analog inputs - tie unused ANx pins to VDD or VSS through a defined resistor to reduce ADC leakage. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet, with all data cross-checked against Microchip's PIC18F24K22/LF24K22 datasheet (DS41398) and current distributor listings as of 2026-09-28.

Permintaan RFG Kontak
PIC18LF24K22T-I/ML - 16KB Flash 8-bit MCU, 64MHz, QFN-28
PIC18LF24K22T-I/ML

PIC18LF24K22T-I/ML - 16KB Flash 8-bit MCU, 64MHz, QFN-28

The Microchip PIC18LF24K22T-I/ML is a 28-pin, 8-bit PIC CMOS flash microcontroller built on the nanoWatt XLP ultra-low-power platform, delivering 16 KB of Flash program memory, 768 bytes of RAM and 256 bytes of EEPROM in a 6x6 mm QFN (28QFN/ML) package with exposed pad. It integrates a 64 MHz internal oscillator capable of 16 MIPS throughput, a 12-bit A/D converter with up to 19 channels, two analog comparators, three CCP/ECCP modules, four 8/16-bit timers, two MSSP (SPI/I2C) ports, two EUSART (LIN-capable) ports and a 32-level hardware stack. The wide VDD range of 1.8V-3.6V with dedicated low-power sleep modes (down to <50 nA typical in RTCC retention) makes the LF variant the preferred choice for battery and energy-harvesting designs, while the F variant targets 5V-tolerance analog rails up to 5.5V. A microcontroller is the programmable central processing unit of any embedded system, combining CPU, memory, peripherals and interrupt logic on a single silicon die. Within Microchip's portfolio, the PIC18F K-series sits in the mid-range 8-bit segment above the baseline PIC16 family and below the 16-bit dsPIC and 32-bit PIC32 families. The LF sub-series denotes the low-VDD variant, while the trailing K22 denotes the 16 KB Flash tier of the PIC18F K22 family. The 'T' suffix in this MPN denotes Tape & Reel packaging and 'I/ML' specifies the industrial temperature grade (-40C to +85C) and the 28-pin ML/QFN package. Key features include: 16 KB Flash (8K x 16), 768 B SRAM, 256 B EEPROM, 25 I/O pins, 12-bit ADC with computation features (ADC2), CTMU charge-time measurement, mTouch capacitive touch support, and nanoWatt XLP power management with multiple idle, sleep and deep-sleep modes. The integrated bootloader removes timer functionality only when the dedicated software bootloader is in use; the part otherwise offers a full suite of timers. Typical applications include battery-powered IoT sensor nodes, wearable health and fitness electronics, low-power wireless sensor accessories, industrial sensor conditioning, USB-to-UART bridges using the EUSART, and ultra-low-power remote controls. Design consideration: the QFN-28 package requires thermal pad soldering for proper ground connectivity; the exposed pad (EP) must be soldered to the board ground plane to meet the datasheet thermal and electrical specifications. This page synthesizes distributor pricing, drop-in alternatives within the same QFN-28 footprint, and practical low-power design notes not found in the manufacturer datasheet alone.

Permintaan RFG Kontak
PIC18LF24K22T-I/MV - 16KB Flash 8-bit MCU, 28-UQFN | Microchip
PIC18LF24K22T-I/MV

PIC18LF24K22T-I/MV - 16KB Flash 8-bit MCU, 28-UQFN | Microchip

The Microchip Technology PIC18LF24K22T-I/MV is a low-power, high-performance 8-bit PIC microcontroller built on the enhanced PIC18 RISC architecture, featuring 16 KB (8K x 16) of Flash program memory and housed in a compact 28-pin UQFN (4x4 mm) package with an exposed thermal pad. Operating from a 1.8V to 3.6V supply, the device executes most instructions in one clock cycle and reaches up to 64 MHz CPU speed, delivering 16 MIPS throughput. The "LF" prefix designates the low-voltage variant that pairs with Microchip's nanoWatt XLP extreme-low-power technology, making it ideal for battery-powered designs. What is a PIC18 LF microcontroller? It is a member of Microchip's 8-bit PIC18 family targeting low-voltage (1.8V-3.6V) operation with the proprietary nanoWatt XLP technology, which provides sleep currents as low as tens of nanoamperates and multiple power-saving modes. Within the broader taxonomy, PIC18 belongs to the 8-bit microcontroller category -> MCU -> embedded microcontroller -> semiconductor IC, sitting alongside PIC16 (mid-range) and PIC24/dsPIC (16-bit) families in Microchip's portfolio. Key features of the PIC18LF24K22T-I/MV include 16 KB self-programmable Flash with 10K erase/write cycles endurance, 768 bytes of RAM, 256 bytes of EEPROM, an integrated 12-bit ADC with up to 17 channels, multiple capture/compare/PWM modules, two Enhanced USART modules, two MSSP (SPI/I2C) peripherals, and a 32 kHz internal oscillator. The device supports CTMU (Charge Time Measurement Unit) for capacitive touch sensing, mTouch capability, and up to 25 mA source/sink current on I/O pins. From an architectural standpoint, the PIC18F K-series uses a 16-bit instruction word and a Harvard bus architecture with separate program and data paths, enabling deterministic single-cycle execution. The "LF" variant specifies an operating voltage range of 1.8V-3.6V, distinguishing it from the standard "F" variant which supports up to 5.5V. The 28-UQFN package with an exposed die pad provides a 4x4 mm footprint suited for space-constrained hand-held modules. Typical applications for the PIC18LF24K22T-I/MV include low-power remote sensor nodes, wearable fitness/health monitors, IoT edge nodes, industrial sensor interface modules, USB/serial bridge firmware using the Enhanced USART, consumer handheld devices, and small appliances requiring capacitive touch controls. Designers select this part when an 8-bit MCU is sufficient for the workload and minimal sleep current is the dominant requirement. Design consideration: ensure the ICSP/ICD pins (PGC/PGD) are reserved for in-circuit serial programming and debugging access; an isolation resistor or jumper is recommended on PGC/PGD lines if the application shares those pins with user circuitry. The exposed thermal pad on the UQFN-28 must be soldered to the board ground plane for mechanical integrity and thermal performance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers and procurement teams a single, actionable reference.

Permintaan RFG Kontak
PIC18LF24K22T-I/SO - 16KB Flash XLP 8-bit MCU | Microchip
PIC18LF24K22T-I/SO

PIC18LF24K22T-I/SO - 16KB Flash XLP 8-bit MCU | Microchip

The Microchip Technology PIC18LF24K22T-I/SO is a low-power 8-bit PIC18 microcontroller with 16 KB Flash, 768 B RAM, and 256 B EEPROM, housed in a 28-pin SOIC wide (SO) package. It operates up to 64 MHz (16 MIPS) and supports 1.8V to 3.6V supply via the LF process variant, targeting nanoWatt XLP applications. A PIC microcontroller (MCU) is a compact programmable processor integrating CPU core, non-volatile Flash program memory, volatile RAM data memory, EEPROM/flash boundary, and a range of digital and communication peripherals on one die - intended for underwater MCU/embedded single board programming. It belongs to the broader category of 8-bit microcontrollers (PIC18 family) - 8-bit microcontrollers -> microcontrollers -> embedded ICs -> integrated circuits. PIC18 microcontrollers are widely adopted because they combine deterministic RISC architecture, low cost, rich peripheral integration, and mature toolchains. Key differentiating specifications include: nanoWatt XLP extreme-low-power technology with typical sleep current below 100 nA, 16 MIPS performance at 64 MHz, 16 KB self-programmable Flash with high-endurance 100K erase/write cycles, 12-bit ADC with up to 17 channels, multiple communication peripherals (EUSART, MSSP SPI/I2C), and configurable on-chip capacitive mTouch sensing. The 28-pin SOIC wide package provides 1.27 mm pin pitch suitable for hand-soldering and moderate-density designs. The PIC18LF24K22 family employs an enhanced Harvard RISC architecture with hardware multiplier and C compiler friendly instruction set. The LF designation indicates the low-voltage (1.8V min) variant, while the F variant runs 2.0V-5.5V. The device integrates mTouch capacitive touch support, PWM, comparators, and an RTC clock with calendar functionality, eliminating many external components in low-power sensor nodes. Typical applications include battery-powered sensor nodes, portable medical devices, low-power IoT edge nodes, consumer remote controls, and industrial metering. The T-suffix tape-and-reel packaging (-T) is intended for high-volume automated assembly. When designing with this device, ensure decoupling capacitors are placed within 5 mm of VDD/VSS pins and that unused I/O pins are configured as outputs to minimize current leakage. The 'T' in the suffix denotes tape-and-reel packaging for SMT assembly. This page synthesizes distributor pricing, drop-in pin-compatible alternatives within the PIC18 family, and practical low-power design notes not consolidated on the manufacturer product page.

Permintaan RFG Kontak