Manajemen Daya
Subkategori
Produk (2.800+)
ITS4090QEPDXUMA1 - 90mΩ Quad Smart High-Side Switch | Infineon
The Infineon ITS4090QEPDXUMA1 is a 90 mΩ quad-channel smart high-side power switch in a PG-TSDSO-14 exposed-pad package, delivering four independent 750 mA outputs from a -0.3 V to 45 V supply range. It belongs to the PROFET 24V/48V family and integrates protection and diagnostic feedback, providing a single-IC solution for switching resistive, capacitive, and inductive industrial loads. A smart high-side switch is a power-distribution semiconductor that sits between a logic-level microcontroller and a ground-referenced load, switching the positive rail rather than ground. Compared with discrete MOSFETs and fuses, these devices integrate over-current, over-temperature, over-voltage, and short-circuit protection, plus a current-sense diagnostic pin. They sit in the hierarchy: load driver -> power distribution switch -> smart high-side switch -> power management IC, replacing legacy electro-mechanical relays and fuses in modern industrial and automotive designs. Key features include typical RDS(ON) of 90 mΩ per channel (140 mΩ at Tj = 125 °C), 750 mA nominal continuous current per channel, integrated reverse-battery protection via GND-path resistor, and a dedicated IS diagnostic pin that delivers a current proportional to load current for fault and load monitoring. The device supports PWM operation up to 1 kHz and offers 4 independent input pins for direct MCU control. Architecturally, the ITS4090Q-EP-D uses four vertical N-channel DMOS output stages driven by charge-pump gate drivers, a central bandgap reference for current sensing, and on-chip thermal sensors. The exposed-pad PG-TSDSO-14 package provides a thermal resistance suitable for 4 × 750 mA simultaneous operation when soldered to adequate copper area, removing the need for external heat sinking in most industrial enclosures. Typical applications include 24 V industrial automation outputs (PLC digital output modules, solenoid and valve drivers), 24 V/48 V building-automation relays and lighting, automotive body controllers for low-power loads, and replacement of electromechanical relays in safety-critical subsystems requiring diagnostic feedback. The wide supply range also tolerates 24 V truck and 48 V mild-hybrid bus voltages. When designing with this part, observe the datasheet recommendation of a 150 Ω resistor between the GND pin and ground for reverse-polarity protection, and ensure PCB copper area keeps junction temperature below 150 °C at maximum concurrent channel load. The IS diagnostic pin requires an external sense resistor and is not intended to drive an ADC directly. This page synthesizes distributor pricing, drop-in PROFET alternatives, and application guidance not collected on any single manufacturer or distributor page, supporting faster selection for industrial and automotive load-driving designs.
ITS4100S-SJ-N - 1A 60V Smart High-Side Switch | Infineon
The Infineon ITS4100S-SJ-N is a protected single-channel Smart High-Side NMOS-Power Switch monolithically integrated in Smart technology, housed in a PG-DSO-8 (DSO-8) package. It delivers up to 1 A continuous load current and tolerates a maximum supply voltage of 60 V, making it well suited to industrial 24 V sensor and actuator rails. The device integrates a vertical power FET, charge pump, CMOS-compatible logic input, and a comprehensive suite of embedded protection and diagnostic functions. A high-side power switch, also called a high-side driver or PROFET (protected FET), is a type of power distribution IC that sits between a positive supply rail and the load. By placing the switch on the high side rather than the low side, the load is grounded during off-state, which improves safety in automotive and industrial systems. The high-side switch category sits within the broader hierarchy of power management ICs, which also includes low-side drivers, half-bridges, and full H-bridges. Compared with discrete MOSFET plus driver designs, an integrated high-side switch significantly reduces PCB area, BOM count, and design complexity while delivering factory-tuned protection. Key features of the ITS4100S-SJ-N include a typical on-resistance of 70 mOhm, integrated overload protection with current limitation, short-circuit protection, thermal shutdown with auto-restart, overvoltage protection including load-dump resilience, and fast demagnetization of inductive loads. The logic input is CMOS-compatible and referenced to ground, simplifying connection to 3.3 V or 5 V microcontrollers. Reverse-battery protection is provided externally with a simple network. A small 1 nF ceramic output capacitor is sufficient for stable operation, and only a few external components are needed to implement a complete protected high-side drive. Typical applications for the ITS4100S-SJ-N include industrial sensor power distribution, PLC digital outputs, relay and solenoid replacement, lighting drivers, and small motor drivers. Its 60 V load-dump tolerance and robust protection make it especially attractive for 24 V industrial automation systems where reliability and immunity to transients are critical. In safety-oriented designs, the integrated diagnostics and protection features reduce the need for external fuses or supervisory circuits. When designing with this part, ensure proper thermal management under sustained high-current loads by providing adequate copper area on the PCB. The PG-DSO-8 thermal pad should be soldered to a sufficient copper pour to keep junction temperature within safe limits. Pay attention to the input pin logic thresholds - a logic low of less than 1.5 V guarantees turn-off, while a logic high above 3.5 V guarantees turn-on for typical 5 V CMOS logic levels. This page synthesizes Infineon distributor pricing, pin-compatible drop-in alternatives from the PROFET family and competitors, and practical design notes not found in the manufacturer datasheet. Source data is cross-referenced against Infineon's official product page and authorized distributors as of 2026-10-08.
ITS4100SSJNXUMA1 - 2A Smart High-Side Power Switch | Infineon
The Infineon ITS4100SSJNXUMA1 is a 2 A smart high-side power switch with an integrated N-channel vertical power MOSFET, housed in a PG-DSO-8 (exposed pad) package. Designed as a single-channel 1:1 power distribution switch, it delivers up to 2 A continuous load current with built-in overload, short-circuit, thermal shutdown (with auto-restart), overvoltage (including load dump), and reverse-battery protection. The device operates across a wide supply range typical of 12 V automotive systems and is part of Infineon's MINI-PROFET family. What is a high-side power switch? A high-side power switch is a semiconductor that sits between the load and the positive supply rail, controlling current flow using an N-channel MOSFET in a high-side configuration. It belongs to the broader category of Power Distribution Switches (PDSw) under Power Management ICs (PMIC). The MINI-PROFET family from Infineon integrates the FET, gate driver, and protection logic into one IC, replacing discrete MOSFET + driver + fuses + TVS solutions and reducing PCB area while improving diagnostic capability. Key features include a typical on-state resistance (RDS(on)) optimized for low conduction loss, current limitation with auto-retry, fast demagnetization of inductive loads (suitable for solenoids, relays, valves), and an analog/digital status feedback pin for fault reporting to the host microcontroller. The PG-DSO-8 exposed-pad package provides a low thermal resistance path, enabling sustained 2 A operation without external heatsinking in typical 12 V automotive loads. Architecturally, the ITS4100SSJNXUMA1 uses a vertical DMOS output structure co-packaged with CMOS control logic. The vertical FET topology minimizes specific on-resistance per unit area versus lateral MOSFETs, while the integrated charge pump generates the gate drive voltage required by the N-channel high-side configuration. Built-in thermal sensors cycle the output off and on (restart behavior) when junction temperature exceeds the shutdown threshold, preventing catastrophic failure during prolonged short-circuit events. Typical applications include automotive body electronics (door modules, seat control, lighting drivers), industrial 24 V PLC outputs, relay and solenoid replacement, heating elements, and any 12 V/24 V load requiring eFuse-style protection. The diagnostic output enables OBD-II-style fault reporting in automotive networks. When designing with this part, ensure the load's inrush current stays below the current-limit threshold or use the soft-start feature (if enabled by external configuration). The exposed pad must be soldered to a sufficient copper pour to achieve rated thermal performance; per JEDEC JESD51, a minimum 1 sq. inch of 1 oz copper on a 4-layer board is typical. This page synthesizes distributor pricing, drop-in alternative cross-references, and practical design notes that complement the official Infineon datasheet, offering information gain not available on any single distributor product page.
ITS4130QEPDXUMA1 - 650mA Quad Smart High-Side Switch | Infineon
The Infineon ITS4130QEPDXUMA1 is a 130 mΩ quad-channel smart high-side power switch from Infineon's PROFET™ Industrial family, rated at 650 mA per channel, housed in a 14-pin PG-TSDSO-14 exposed-pad package. The device integrates four independent high-side switches with on-state resistance of 205 mΩ typical at Tj=125°C, supporting 45 V load-dump tolerance for harsh industrial and automotive 24V/48V environments. A high-side power switch is a semiconductor switch that sits between the supply rail and the load, controlling current flow from the high side of the load to ground. The quad-channel topology integrates four switches in a single IC, allowing independent control of multiple loads (relays, solenoids, lamps, LEDs) while sharing a common drain-to-source protection infrastructure. Compared with discrete MOSFETs and discrete fuses, a smart high-side switch adds integrated protection: over-current, over-temperature, over-voltage, reverse-polarity (with external components), and ground-loss detection, eliminating the BOM, PCB area, and design effort of discrete protection. Key features include a single supply operating range, per-channel diagnostic feedback, very low typical RDS(ON) of 205 mΩ at Tj=125°C, integrated protection functions, and reverse-polarity protection achievable with an external 150 Ω power resistor between GND and ground. The PG-TSDSO-14 package provides an exposed thermal pad that lowers θJA, enabling sustained quad-channel operation at 650 mA per channel without external heatsinking in typical industrial ambient conditions. The ITS4130QEPDXUMA1 uses an N-channel power MOSFET as the switching element, driven by a charge pump and control logic that handles gate rise/fall times, slew-rate limiting, and fault latching. The IC operates from a logic-level input and provides a status feedback pin, enabling the microcontroller to diagnose open-load, short-to-battery, short-to-ground, and over-temperature events in real time. Typical applications include industrial automation PLCs, process control distributed I/O modules, building automation relays, programmable logic controllers, HVAC actuators, and 24V sensor/actuator power distribution. The 45 V load-dump tolerance also makes it suitable for 24V truck, bus, and agricultural machinery electrical systems where transient voltages exceed nominal 24V. When designing with this device, ensure that the GND pin is correctly referenced because reverse-polarity protection requires an external 150 Ω resistor or a reverse current diode plus 27 Ω series resistor in the GND path. Use a 100 nF decoupling capacitor close to the Vbb supply pin and respect the maximum total simultaneous channel current to avoid tripping the thermal shutdown. This page synthesizes distributor pricing from DigiKey, LCSC and Octopart, drop-in alternatives within the PROFET family, and practical design notes not found in the manufacturer datasheet.
ITS4140NHUMA1 - 200mA High-Side Smart Switch | Infineon
The Infineon ITS4140NHUMA1 is a 200 mA high-side power switch with an integrated vertical N-channel power FET, housed in a 4-pin PG-SOT223-4 (3+Tab) surface-mount package. The device operates from 4.9 V to 60 V supply, supports a 1:1 input-to-output topology, and embeds short-circuit protection, current limitation, overload protection, overvoltage protection (including load dump), and negative-voltage output clamping for inductive loads. A high-side switch is a power-distribution IC that controls a load by switching the positive supply rail rather than ground return; this topology, also called a smart power switch or PROFET, sits in the PMIC (Power Management IC) hierarchy between discrete MOSFETs and fully-integrated system-basis chips. Compared with an electromechanical relay, a high-side switch provides silent, bounce-free switching, integrated diagnostics, and far faster fault response; compared with a discrete MOSFET plus fuse, it self-protects without external components. The ITS4140N integrates a charge pump that drives the internal N-channel FET, a precise current limit, thermal shutdown, and ground-loss detection. Diagnostic feedback is provided through the IN/status pin, simplifying wire harness troubleshooting. Switching inductive loads such as solenoids, relays, and small motors is handled with internal active clamping that absorbs the back-EMF without external freewheeling diodes, simplifying PCB layout. Designed for 12 V and 24 V industrial environments, the part withstands load-dump transients per ISO 7637-2 and is suitable for automotive and truck body electronics where the supply bus can swing well above nominal. Its 200 mA continuous current limit makes it ideal for driving small lamps, signal LEDs, sensors, and logic-level loads without external heatsinking. When designing with this device, observe maximum input voltage (60 V) under worst-case load-dump, derate current with ambient temperature above 25C, and place the input capacitor within 5 mm of the Vbb pin. The exposed tab is the power-dissipation path and must be soldered to a copper pour of at least 100 mm squared. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
ITS4141NHUMA1 - 700mA Smart High-Side Switch | Infineon PROFET
The Infineon ITS4141NHUMA1 is a 700 mA single-channel smart high-side power switch housed in a PG-SOT223-4 (TO-261-4) surface-mount package with integrated vertical N-channel power FET, embedded protection, and diagnostic feedback. It operates from a load supply range of -10 V to 48 V (extended to 12 V to 45 V in PROFET Industrial datasheet specification) with a typical on-state resistance of 200 mΩ, and is intended for industrial automation, process control, and PLC digital output modules. What is a high-side power switch? A high-side power switch is a type of power distribution switch (sub-category: load driver) that sits between the positive supply rail and the load, controlling current flow by turning the integrated MOSFET on and off in response to a logic-level input. Within the broader taxonomy, the high-side switch belongs to: PMIC -> Power Distribution Switch -> Load Driver -> High-Side Switch. Infineon's PROFET family is the industry-leading implementation using a vertical N-channel FET for low R_DS(on) and high energy robustness. Key features include short-circuit protection with current limitation, overload protection, overvoltage protection including load-dump, undervoltage shutdown with auto-restart and hysteresis, plus an open-drain status diagnostic pin. The 200 mΩ R_DS(on) at 25 °C minimizes conduction losses, while the integrated charge pump drives the gate of the N-channel FET for true high-side switching with a standard 3.3 V or 5 V CMOS logic input. PG-SOT223-4 provides a low thermal resistance path via the central tab, enabling continuous 700 mA operation without external heatsinking. The architecture is built on Infineon's Smart Power technology - a vertical DMOS output stage with monolithic CMOS control logic. The diagnostic pin reports open-load, overtemperature, and overcurrent events back to the microcontroller, while the auto-restart behavior allows the part to recover automatically once a fault clears, reducing firmware complexity in PLC and process-control applications. Typical applications include 24 V industrial PLC digital outputs, factory-automation I/O modules, sensor and actuator power distribution, building-automation relay drivers, and battery-protected low-side-of-24V systems. The wide V_S range with load-dump tolerance makes it especially suited for 24 V truck and bus body-controller applications. When designing with this part, respect the 700 mA continuous current limit and place the tab solder pad on at least 1 cm² of copper pour to keep R_thJA low enough for the SOA. The status pin requires a pull-up resistor and is open-drain; ensure input transitions are below 5 V CMOS thresholds for noise-immune switching. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.
ITS4142NHUMA1 - 1.4A Smart High-Side Switch SOT-223 | Infineon
The Infineon ITS4142NHUMA1 is a single-channel smart high-side power switch with an integrated vertical N-channel power FET, housed in a 4-pin SOT-223 (PG-SOT223-4) surface-mount package. It delivers up to 1.4 A continuous load current and replaces electromechanical relays and discrete switching circuits with a robust solid-state solution that includes embedded protection and diagnostic functions. What is a high-side power switch? A high-side power switch is a semiconductor device placed between the positive supply rail and the load. By switching on the high side, the load is referenced to ground when off, eliminating ground loops and improving safety in industrial automation. High-side switches belong to the broader category of power distribution switches within power management ICs. Compared to low-side switches or electromechanical relays, smart high-side switches provide on-resistance control, fault feedback, and protection features in a single monolithic IC. The ITS4142N integrates short-circuit protection with current limitation, overload protection, overvoltage protection including load-dump transients, undervoltage shutdown with auto-restart and hysteresis, and inductive-load switching capability. These features enable it to drive resistive, inductive, and capacitive loads in harsh 12 V and 24 V automotive and industrial environments. The logic-level input is compatible with 3.3 V and 5 V microcontrollers, simplifying digital control. Architecturally, the device uses Infineon's SIPMOS vertical power MOSFET technology, which minimizes on-state conduction losses versus lateral MOSFETs. The integrated charge pump drives the gate of the N-channel FET to provide a true low-resistance path from supply to load. An onboard thermal shutdown circuit protects the die during overload events, while open-drain diagnostic feedback signals fault conditions to the host microcontroller. Typical applications include 24 V industrial PLC outputs, automotive body-control modules, relay replacement in HVAC and lighting systems, programmable logic controller digital outputs, and solenoid or valve drivers. With its wide operating voltage range and embedded protection, the ITS4142N is well suited for IEC 61131-2 compliant industrial digital outputs. When designing with this part, ensure that input debouncing and proper TVS protection are applied to the load lines for long-term reliability, and verify junction temperature under worst-case continuous load. A key design trade-off is RDS(on) versus quiescent current; the ITS4142N favors low on-resistance for minimal load-side dissipation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, supporting both new designs and relay-replacement retrofits.
ITS41K0SMENHUMA1 - 1Ω 60V 200mA Smart High-Side Switch | Infineon
The Infineon ITS41K0SMENHUMA1 (ITS41K0S-ME-N) is a 200 mA smart high-side N-channel power switch housed in a PG-SOT223-4 surface-mount package. It integrates a 1 Ω typical on-state MOSFET channel with full protection features for industrial load driving. The device operates from 4.9 V to 60 V supply rails and is part of the PROFET Industrial MINI-PROFET family. A high-side power switch (also called a load switch or smart switch) is a semiconductor device that controls power delivery to a downstream load by switching the positive supply rail. Compared with a discrete MOSFET plus fuse arrangement, a smart high-side switch integrates the switching transistor, gate driver, current limit, thermal protection, ESD protection, and diagnostic feedback into one IC. This integration reduces PCB area, eliminates external fuses, and provides fault reporting to the host microcontroller. The ITS41K0S family belongs to the broader Infineon PROFET (Protected MOSFET) product hierarchy used in industrial, home appliance, and building automation systems. Key features include a 60 V maximum load-dump tolerant supply rating, 800 mΩ maximum on-resistance (R_DS(on)), and 200 mA continuous load current capability. Built-in protection includes thermal shutdown with auto-restart, overcurrent protection with current limiting, overvoltage clamp (active clamp against automotive load-dump transients), ESD protection on the IN/DEN pins, and reverse-battery robustness with ground-loss tolerance. The PG-SOT223-4 package provides a thermal pad for PCB heat spreading and supports up to approximately 1 W dissipation with proper layout. Technically, the ITS41K0SMENHUMA1 uses an N-channel vertical power MOSFET with a charge pump to drive the gate above the supply rail, allowing true low-R_DS(on) high-side switching. A status feedback pin provides diagnostic information to the microcontroller. The device is qualified for industrial environments, supporting -40°C to +125°C junction operation. Typical applications include industrial PLC digital outputs, relay and solenoid replacement, building automation controls, home appliance driver stages (washing machines, dishwashers, white goods), and small motor or valve drivers. The 60 V rating makes it well suited for 24 V industrial bus systems with significant transient margin. When designing with this part, ensure the input capacitor (typically 100 nF close to the Vbb pin) and output capacitor are sized according to the application load profile. The exposed pad must be soldered to a copper pour of at least 1 cm² to keep junction temperature within safe limits at sustained loads. The diagnostic output requires proper pull-up configuration per the datasheet. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers select and source the ITS41K0SMENHUMA1 with confidence.
ITS4200SMENHUMA1 - 700mA 41V Smart High-Side Switch | Infineon
The Infineon ITS4200SMENHUMA1 is a protected single-channel Smart High-Side NMOS Power Switch in a SOT-223-4 (PG-SOT223-4) package with charge pump and CMOS-compatible input, monolithically integrated in Infineon Smart technology (PROFET™ Industrial family). The device delivers up to 0.7 A continuous load current, 41 V overvoltage protection (including load-dump), and embedded thermal shutdown, short-circuit protection with current limitation, and undervoltage shutdown. The logic-level CMOS input enables direct MCU GPIO control without level shifters. A high-side power switch (also called a smart high-side driver) is a power distribution IC that sits between a positive supply rail and a load, providing controlled turn-on, protection, and diagnostic feedback. Unlike a low-side switch (which switches the load to ground), a high-side switch returns load current directly to ground when the FET is on, eliminating ground-shift noise and offering short-to-ground protection by default. The high-side switch family sits inside the broader taxonomy: power switch IC -> power management IC -> semiconductor device. Related Infineon families include PROFET™, HITFET™, and SPOC™ for various current ranges. Key features include 0.7 A nominal load current, 41 V load-dump overvoltage protection, embedded thermal shutdown with restart, short-circuit current limitation, open-load detection in OFF state, and very low quiescent current (microamp range) for always-on applications. The CMOS-compatible input pin provides a clean logic interface with pull-down current. The monolithic Smart technology integration puts the vertical power FET, charge pump, and protection logic on a single die. The ITS4200S-ME-N variant (its full part designation behind the SP-number ITS4200SMENHUMA1) is targeted at industrial-grade applications requiring robust protection. The internal charge pump drives the gate of the N-channel MOSFET above the supply rail so the device behaves as an ideal high-side switch. Diagnostic feedback via the status pin supports advanced fault handling. According to the manufacturer datasheet, the part is not qualified for automotive use per Infineon policy. Typical applications include industrial PLC digital outputs, building automation relay replacement, USB downstream power switching, sensor and actuator power distribution, and small DC load control in 12 V and 24 V industrial systems. The wide operating voltage range (5 V to 41 V) covers 12 V and 24 V nominal buses including load-dump transients. When designing with this part, ensure the load current stays below 0.7 A nominal (1 A peak) and respect the SOT-223-4 thermal resistance (around 70 C/W on a standard 2-layer 1 oz PCB) by adding a copper pour under the tab. The status pin needs a pull-up resistor if diagnostics are required; leave it floating otherwise to minimize quiescent current. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
ITS4200SMEOHUMA1 - 700mA Smart High-Side Switch | Infineon
The Infineon ITS4200SMEOHUMA1 is a 700 mA smart high-side N-channel MOSFET power switch housed in a 4-pin PG-SOT223-4 (3 leads + tab) surface-mount package, monolithically integrated in Infineon's SMART technology. It delivers a typical on-state resistance of 150 mOhm, supports nominal operating voltages up to 45 V with load-dump protection, and provides an embedded CMOS-compatible input pin with internal charge pump for true logic-level gate drive. A smart high-side switch (also called a high-side driver, smart power switch, or PROFET) is a power-distribution IC that sits between an upstream supply and a downstream load, replacing a discrete MOSFET plus discrete protection circuitry. It belongs to the broader power-management category: high-side switch -> power distribution switch -> power management IC -> semiconductor. By placing the switch on the high side of the load, the device allows loads (such as lamps, solenoids, relays, or resistive heaters) to share a common ground return, simplifying PCB routing and improving system safety because fault currents flow back through the chassis ground. Key features include fixed current limiting, overtemperature shutdown with auto-restart, short-circuit protection with shutdown, overvoltage protection including load dump, ground-loss protection, and ESD protection on the input pin and the load output. The CMOS-compatible input is current-controlled, allowing direct drive from a microcontroller GPIO without level shifting. Reverse-battery protection is achieved through the body diode of the internal power MOSFET in conjunction with an external resistor. The architecture combines a vertical power DMOS output stage, a charge pump to generate the gate-drive voltage above the supply rail, and analog protection blocks for current sense, thermal sense, and voltage monitoring. This monolithic integration is what differentiates ITS-class parts from discrete FET-plus-driver solutions: it eliminates layout-induced parasitic inductance issues and provides guaranteed, tested protection thresholds rather than discrete-component tolerances. Typical applications include PLC digital outputs, sensor and actuator power distribution in industrial automation, body-control modules in automotive systems, LED driver switching, relay and solenoid drivers, and general 24 V industrial bus switching. Its 700 mA continuous current limit and 45 V transient rating make it especially suited to 24 V PLC and truck/bus 24 V systems where load-dump transients up to 45 V must be tolerated without damage. When designing with this device, place a reverse-polarity protection diode or P-MOSFET at the supply input to handle full-load reverse-battery events, and ensure adequate copper area on the tab (pin 4) for thermal dissipation. The current-controlled input means a single series resistor sets both the input current and the logic threshold; do not drive the input with a hard voltage source without this resistor. This page synthesizes distributor pricing, drop-in alternatives from authorized sources, and practical design notes not found in the manufacturer datasheet alone.
ITS4200SMEPHUMA1 - 1.4A Smart High-Side Switch | Infineon
The Infineon ITS4200SMEPHUMA1 is a protected single-channel Smart High-Side N-Channel MOSFET power switch with 1.4 A continuous load current, 150 milliohm typical on-state resistance (Rdson), and integrated vertical power FET monolithically fabricated in Infineon's Smart technology, housed in a 4-pin PG-SOT223-4 surface-mount package. The device operates across an extended -3 V to 45 V supply range and combines a charge pump with a CMOS-compatible logic input, enabling direct 3.3 V/5 V microcontroller GPIO drive without level shifting. A high-side power switch (also called a load switch, smart switch, or solid-state eFuse) is a power distribution switch placed between the supply rail and the load. Compared with discrete fuses, MOSFETs, and electromechanical relays, smart high-side switches integrate the power FET, gate driver, current sense, and protection state machine on a single die. The ITS4200S-ME-P belongs to the MINI-PROFET family from Infineon, optimized for high-current drive capability in the compact SOT-223-4 footprint. Within the broader taxonomy, this part is a power management IC (PMIC) sub-class: power distribution switch -> high-side switch -> smart high-side switch -> PROFET -> MINI-PROFET. Key features include current-controlled input, current limitation, short-circuit protection, undervoltage shutdown, overvoltage protection with load-dump resilience up to 45 V, thermal shutdown with auto-restart, and the ability to switch inductive loads. The CMOS-compatible logic input and the integrated charge pump simplify interface design and eliminate external bootstrap components, reducing BOM cost in 12 V/24 V systems. Architecturally, the ITS4200SMEPHUMA1 integrates a vertical N-channel DMOS output stage, on-chip charge pump for gate drive generation, current sense amplifier, and a fault state machine that handles short-circuit, overvoltage, undervoltage, and thermal events. This monolithic integration delivers a robust solid-state alternative to electromechanical relays, supporting harsh automotive electrical environments including cranking transients and load-dump surges on 12 V buses. Typical applications include automotive body electronics (interior lighting, seat control, mirror heating, HVAC actuators), industrial PLC outputs and solenoid drivers, and any 12 V/24 V bus requiring protected high-side switching. The AEC-Q100 qualification makes the part suitable for under-hood and passenger-compartment automotive modules where reliability under thermal cycling and electrical transients is mandatory. When designing with this device, ensure adequate PCB copper area on the tab/heatsink pad to dissipate I²R losses. The ITS4200SMEPHUMA1 includes built-in protection, but designers should still validate fault-recovery behavior with their specific load profile and verify inrush behavior at cold temperature extremes. This page synthesizes distributor pricing, drop-in MINI-PROFET alternatives, and practical design notes not found on the manufacturer datasheet alone.
ITS4200SSJDXUMA1 - 1.2A Smart High-Side Switch | Infineon PROFET
The Infineon ITS4200SSJDXUMA1 is a 200 mOhm single-channel smart high-side power switch built on Infineon's PROFET (Protected MOSFET) platform, housed in a PG-DSO-8 package. It delivers 1.2 A continuous load current with 6 V to 52 V operating supply range, integrating a vertical N-channel power MOSFET with comprehensive embedded protection and diagnostic functions for industrial and automotive 24 V loads. A smart high-side switch is a power distribution switch that sits between the supply rail and the load, providing controlled turn-on/turn-off, current limiting, and fault feedback. Within the broader taxonomy, this part belongs to the PROFET family -> intelligent power switch (IPS) -> high-side driver -> load driver -> power management IC. Compared to a discrete MOSFET plus fuse, the ITS4200SSJDXUMA1 eliminates external protection components, simplifies PCB layout, and provides real-time status feedback to the microcontroller. Key specifications include 200 mOhm typical on-state resistance (R_DS(on)), 1.2 A continuous drain current, 6 V to 52 V supply range, and 0.8 mA quiescent supply current. The device features overload protection, current limitation, short-circuit protection with thermal shutdown and auto-restart, overvoltage protection including load-dump transient tolerance, undervoltage shutdown, and fast demagnetization of inductive loads. A diagnostic status output flags open-load and overtemperature conditions back to the host MCU. The ITS4200SSJDXUMA1 uses Infineon's vertical DMOS process for low R_DS(on) per area and integrates charge pump, gate driver, sense-FET, and protection logic on a single die. The 8-pin DSO footprint exposes IN, OUT, GND, Vbb, and a single status pin, simplifying PCB routing versus multi-channel PROFET alternatives. Maximum power dissipation is 1400 mW. Typical applications include 24 V industrial relay and solenoid drivers, PLC digital outputs, automotive body electronics (lighting, door modules, seat controllers), and resistive/inductive load management. The 52 V load-dump tolerance makes it directly compatible with 12 V and 24 V automotive buses. When designing with the ITS4200SSJDXUMA1, place a 100 nF ceramic bypass capacitor close to Vbb and verify heatsinking for continuous 1.2 A loads above 25 C ambient. Use the status pin to flag fault conditions to the host MCU rather than relying on software polling of the output voltage. This page synthesizes Infineon distributor pricing, PROFET family drop-in alternatives (ITS4100SSJNXUMA1, BTS462TATMA1), and practical design guidance for 24 V load switching that the manufacturer datasheet alone does not consolidate.
ITS428L2ATMA1 - 5.8A Smart High-Side Power Switch | Infineon
The Infineon ITS428L2ATMA1 is a 5.8A single-channel smart high-side power switch in a PG-TO252-5-11 (TO-252-5 / DPAK-4 leads + tab) surface-mount package. It monolithically integrates a vertical N-channel power MOSFET with a charge pump, ground-referenced CMOS-compatible input, and diagnostic feedback, and is fabricated using Infineon's Smart SIPMOS technology. The part targets 5 V, 12 V, and 24 V DC grounded industrial loads and is part of the PROFET Industrial family. A high-side switch is a power-distribution topology in which the load is tied to ground and the switch sits between the positive supply rail and the load. Compared with low-side switching, high-side architecture eliminates a permanent ground path, simplifies fault detection, and protects downstream wiring from shorts to ground. Smart high-side switches add on-chip protection (overload, short-circuit, overvoltage/load-dump, overtemperature) and a status/diagnostic output that the microcontroller can read for fault handling. Key features of the ITS428L2ATMA1 include a typical on-resistance in the low milli-ohm range for low conduction loss, a continuous load current capability up to approximately 5.8 A, CMOS-compatible logic input for direct 3.3 V or 5 V micro-controller drive, integrated overvoltage protection including load dump via an external resistor, and a diagnostic feedback pin for open-load, short-to-ground, short-to-battery, and overtemperature reporting. The PROFET family is engineered to handle high inrush currents typical of lamps, solenoids, motors, and capacitive loads. Typical applications include industrial 24 V PLC digital outputs, relay and solenoid replacement, automotive body and chassis modules (12 V), building automation, and any general resistive, inductive, or capacitive 5 V - 24 V load. When designing with this part, ensure the supply voltage stays within the supported range, add the recommended external resistor for overvoltage/load-dump clamping, and observe thermal limits at maximum continuous current. The TO-252-5 package requires sufficient copper pad area for heat dissipation. This page aggregates distributor pricing, drop-in PROFET family alternatives, and practical design notes beyond the manufacturer datasheet.
ITS42K5DLDFXUMA1 - Dual 250mA PROFET High-Side Switch | Infineon
The Infineon ITS42K5DLDFXUMA1 is a dual-channel high-side power switch from the PROFET (Protected MOSFET) 24V/48V family, delivering two independent 250 mA channels in a compact 10-pin PG-TSON-10-2 (TSON EP) exposed-pad package. Each channel integrates a P-channel power MOSFET with on-state resistance of 2.5 ohm and a built-in freewheeling diode, providing clamped inductive-load switching up to 13.5 V supply operation. A PROFET high-side switch is a smart power switch that combines a MOSFET output stage, gate driver, and comprehensive protection circuitry in one IC. It belongs to the power distribution switch category within the broader power management IC (PMIC) hierarchy, sitting between discrete MOSFETs (which need external drivers and protection) and fully-integrated system basis chips (which add CAN/LIN transceivers). PROFET switches are commonly used in automotive body and powertrain modules where they replace discrete relays with PCB-mountable, diagnostically-rich equivalents. Key features include dual 250 mA continuous current per channel, 2.5 ohm Rds(on) typical, integrated freewheeling diode per output, status feedback, and protection functions (overload, short-circuit, thermal shutdown, overvoltage clamp). The 1:1 input-to-output switch topology provides simple logic-level control from a microcontroller GPIO. Operating voltage range supports both 12 V and 24 V automotive buses with reverse-battery robustness. Architecturally, each channel uses a vertical P-channel DMOS output transistor driven by a charge-pump-derived gate drive, with current-sensing and temperature-sensing blocks feeding back into a fault-management state machine. The exposed thermal pad on the bottom of the TSON-10-2 package provides a low thermal-resistance path (~30 C/W typical) to the PCB copper, enabling sustained operation at the rated current without external heatsinking. Typical applications include automotive body control modules (BCM), HVAC actuators, LED lighting drivers, sensor power distribution, and industrial 24V PLC outputs. The dual-channel design is particularly efficient for paired loads such as bidirectional motors or two indicator lamps sharing one IC. When designing with this part, place the exposed pad on a copper pour of at least 1 square centimeter to keep junction temperature within rating at full load. The status pin requires a pull-up resistor; consult the datasheet for diagnostic truth-table behavior in fault conditions. This page synthesizes Infineon datasheet parameters, distributor pricing, drop-in alternatives, and practical design notes not found on a single distributor product page, giving engineers a one-stop reference for evaluation and BOM decisions.
ITS4300SSJDXUMA1 - 400mA Smart High-Side Switch | Infineon
The Infineon ITS4300SSJDXUMA1 is a 400 mA smart high-side power switch with an integrated vertical N-channel power FET, housed in a PG-DSO-8 package. It provides embedded protection and diagnostic functions for 12 V and 24 V DC industrial applications, with a low typical on-state resistance of 300 mΩ and CMOS-compatible control interface. A high-side power switch (also called a smart high-side driver or PROFET) is a type of power distribution switch that sits between the supply rail and the load, replacing discrete MOSFETs, fuses, and relay circuits. The category hierarchy is: high-side switch -> load driver -> power distribution switch -> PMIC (Power Management IC) -> semiconductor. Smart high-side switches integrate overcurrent, short-circuit, thermal, overvoltage, and undervoltage protection, dramatically simplifying the BOM and improving system reliability. Key features include overload protection with current limitation, short-circuit protection, thermal shutdown with auto-restart, overvoltage protection including load-dump, shutdown on undervoltage, fast demagnetization of inductive loads, and ESD protection. The CMOS-compatible input makes it directly compatible with 3.3 V and 5 V microcontrollers. The device is qualified for industrial applications per JEDEC JESD47. Technically, the ITS4300S uses a vertical N-channel DMOS output stage driven by a charge pump that generates the gate boost voltage needed for full enhancement of the high-side FET. The integrated charge pump, current sense, and protection logic are all on a single piece of silicon, achieving a typical RDS(on) of 300 mΩ at 25°C. The fast demagnetization circuit handles the inductive kickback of relays, solenoids, and small motors, allowing unclamped inductive switching up to the device's internal energy rating. Typical applications include driving resistive, inductive, and capacitive loads in industrial automation, programmable logic controllers (PLCs), sensor power distribution, electromagnetic relay drivers, and any 12 V/24 V high-side switching application with low standby current requirements. The part is also used as a power management switch for low-current standby rails. When designing with this device, ensure the load current stays below 400 mA continuous and that the inductive load's energy does not exceed the device's single-pulse avalanche rating. A reverse-polarity protection diode or P-channel FET is recommended at the supply input since the ITS4300S does not include internal reverse-battery protection. Good PCB layout practices (wide traces, short ground returns) help minimize voltage transients. This page synthesizes distributor pricing, drop-in PROFET alternatives, and practical design notes not found in the manufacturer datasheet alone.
ITS4880R - 8-Ch 0.625A Smart High-Side Switch | Infineon
The Infineon ITS4880R is an 8-channel smart high-side power switch (PROFET Industrial family) delivering 0.625 A per channel for 24 V DC industrial loads, monolithically integrated in Smart SIPMOS technology. Each of the eight channels features an N-channel vertical power FET with charge pump, ground-referenced CMOS or Vbb/2-compatible input, and common diagnostic feedback, housed in a PG-DSO-36-26 power package. Operating supply range spans roughly 11 V to 45 V with 60 V load-dump transient capability for direct 24 V industrial bus use. A high-side switch is a power-distribution topology that places the MOSFET between the supply rail and the load, allowing logic-level signals to switch the grounded load safely. Within the broader semiconductor hierarchy, the ITS4880R sits in the PMIC > Power Distribution Switch / Load Driver category, often called a smart power switch or PROFET (Protected FET) when diagnostic and protection features are integrated. The 8-channel parallel architecture lets one IC replace eight discrete low-side drivers plus protection circuitry, reducing PCB area and BOM count in 24 V multi-load systems. Key features include 0.625 A nominal per-channel current, 8 independently controlled inputs, integrated charge pump for full N-channel enhancement, common diagnostic output, embedded protection (overload, short-circuit, over-temperature, ESD, and over-voltage clamp), and CMOS or Vbb/2 input compatibility. The common-diagnostic feedback pin reports open-load and overtemperature conditions to the host MCU, simplifying firmware state machines. Internally the ITS4880R combines a vertical DMOS output stage with a charge-pump gate driver and per-channel protection logic on a single Smart SIPMOS die. The Vbb/2 input option allows direct connection to 5 V microcontrollers without level shifters. Common diagnostic feedback consolidates eight per-channel fault signals into one pin, saving MCU GPIOs and reducing wiring complexity in 24 V PLC and industrial-automation backplanes. Typical applications include 24 V industrial automation (PLC digital outputs), process-control solenoid and valve drivers, building-automation relay replacement, sensor and indicator power distribution, machine-tool lamp and actuator control, and HVAC damper/valve arrays. The wide Vbb tolerance and load-dump rating make it well suited to factory-floor environments with long cable runs and inductive transients. When designing with this device, derate per-channel current to roughly 0.4-0.5 A continuous when all eight channels conduct simultaneously, because the PG-DSO-36-26 package shares thermal capacity. Always place a reverse-polarity and TVS clamp on Vbb, and use series inductance mitigation (freewheel diode or TVS) when switching solenoids or relays. This page synthesizes distributor pricing, drop-in alternatives from the Infineon PROFET family, and practical PCB design notes for 24 V industrial loads not found in the manufacturer datasheet alone.
ITS6080SEPDXUMA1 - 8A Smart High-Side Switch | Infineon
The Infineon ITS6080SEPDXUMA1 is a single-channel smart high-side power switch from Infineon's PROFET Industrial 75 mOhm family, delivering up to 8A continuous output current in a 14-pin PG-TSDSO package with exposed thermal pad. The device integrates a vertical N-channel power MOSFET with 75 mOhm typical on-state resistance, comprehensive protection features, and diagnostic feedback, designed for 12V and 24V industrial and automotive load-driving applications. A high-side switch (HSS) is a power distribution IC that sits between a positive supply rail and a load, allowing a low-voltage logic signal (typically 3.3V or 5V microcontroller GPIO) to control a much larger load current while providing protection against overloads, short circuits, and thermal faults. Compared with a discrete MOSFET plus fuse solution, an intelligent high-side switch integrates the power transistor, charge pump gate drive, current sense, and fault diagnostics into a single package, reducing PCB area, BOM count, and design complexity. The ITS6080 belongs to the family tree: high-side switch -> power distribution switch -> power management IC -> semiconductor. Key specifications include 75 mOhm typical on-resistance at 25C, an operating supply range of 5V to 34V (with load-dump survival up to 62V), 8A continuous drain current, and integrated protections including overload current limiting, short-circuit shutdown, thermal shutdown, over-voltage clamp, and ESD protection. The device offers proportional load current sense output for diagnostic monitoring and an active-low fault feedback pin for system-level safety. The ITS6080 employs a vertical DMOS output stage with an integrated charge pump that fully enhances the N-channel MOSFET regardless of supply voltage, achieving true low-Rds(on) across the full operating range. This contrasts with older P-channel high-side architectures that suffer from higher on-resistance at low supply voltages. The device is qualified to AEC-Q100 for automotive harsh environments. Typical applications include driving resistive, inductive, and capacitive loads such as solenoids, valves, relay coils, LED strings, motors, and heaters in body electronics modules, industrial automation PLCs, and process control systems. The 8A rating suits medium-power actuators where a robust, self-protected switch replaces discrete solutions. When designing with this device, derate the load current for ambient temperature and PCB copper area. Use a 100nF ceramic decoupling capacitor directly at Vbb and follow the application note's PCB layout guidelines to ensure the exposed pad dissipates heat efficiently into the copper plane. This page consolidates distributor pricing, PROFET family variants, and PCB layout recommendations not present in the standalone datasheet, providing a single engineering reference.
ITS711L1FUMA1 - 4-Ch Smart High-Side Switch 1.7A PG-DSO-20 | Infineon
The Infineon ITS711L1FUMA1 is a 4-channel smart high-side power switch built on Smart SIPMOS technology, housed in a PG-DSO-20-31 package and rated for 1.7A continuous output current per channel (4A total package capability). It operates over a load voltage range of 5V to 34V, making it directly suited to industrial 12V and 24V DC grounded load systems. Key features include an integrated charge pump for N-channel vertical power FET operation, ground-referenced CMOS-compatible logic inputs, embedded diagnostic feedback for each channel, and monolithic protection functions including over-load, over-voltage, over-temperature, and short-circuit handling. The PROFET (Protected FET) Industrial family design replaces electromechanical relays and discrete MOSFET driver circuits, providing a single-chip solid-state solution. The ITS711L1 is a member of the high-side switch category within the broader power distribution switch hierarchy. High-side switches sit between the supply rail and the load (versus low-side switches which sit between load and ground), allowing them to provide complete load disconnect and ground-referenced control logic. The 1:1 input-to-output ratio and four parallel outputs make this part suitable for driving multiple resistive, inductive, or capacitive loads from a single microcontroller I/O bus. Technical depth: the device integrates four vertical N-channel power MOSFETs, a charge pump to drive the high-side gates above the supply rail, CMOS input buffers, and per-channel sense/current-limit circuitry. Diagnostic feedback (open-drain status) lets the host microcontroller distinguish normal operation from open-load, short-to-ground, short-to-battery, and thermal shutdown events. The Smart SIPMOS process combines a vertical DMOS power stage with CMOS control logic on a single die. Typical applications include industrial automation PLC outputs, 24V solenoid and valve drivers, building management relay replacement, programmable logic controller (PLC) discrete outputs, and machine safety interfaces. The wide 5V-34V input range covers both 12V automotive subsystems and 24V industrial battery-backed rails. When designing with the ITS711L1FUMA1, derate output current at elevated ambient temperatures following the thermal resistance curve in the datasheet, and place sufficient copper pour under the exposed pad to keep junction temperature below the shutdown threshold. Inputs are CMOS-compatible, eliminating the need for level-shifters in 3.3V or 5V microcontroller systems. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers select and qualify the ITS711L1FUMA1 for production designs.
ITS716GFUMA1 - 4-Ch Smart High-Side Switch 2.3A | Infineon
The Infineon ITS716GFUMA1 is a 4-channel smart high-side power switch with integrated vertical power MOSFETs, delivering 2.3 A continuous current per channel in a PG-DSO-20-32 (20-pin SOIC) package. It provides embedded protection (overload, short-circuit, over-temperature, over-voltage) and diagnostic feedback for microcontroller-driven 12 V and 24 V DC grounded loads in industrial applications. A smart high-side switch is a semiconductor relay that sits between the supply rail and the load, replacing electromechanical relays and fuses. Unlike a simple MOSFET, it integrates logic-level GPIO control, current sensing, slew-rate limiting, and fault reporting into a single IC. The ITS716GFUMA1 belongs to Infineon's PROFET Industrial family, which targets PLC I/O, process automation, and building-control systems where the device must survive harsh electrical environments and inductive load transients. Key features include four independent channels each rated up to 2.3 A, SPI-compatible diagnostic feedback (open-load, short-to-ground, short-to-battery, overtemperature), very low standby current, and broad operating voltage from 5 V to 36 V (load-dump tolerant to 45 V). The vertical power FET topology minimizes on-resistance per channel while maintaining a small footprint. The PG-DSO-20-32 exposed-pad package provides a low thermal resistance of about 36 C/W, enabling sustained operation across multiple parallel channels in industrial cabinets. The device is engineered for direct connection to a microcontroller's GPIO pins through its parallel input interface, with one logic input per channel plus a shared enable and diagnostic output. The internal charge pump and gate driver handle PWM operation up to 1 kHz for LED dimming or solenoid proportional control without external driver components. The ITS716GFUMA1 is qualified to Infineon's industrial grade (-40 C to +85 C ambient) with extended ESD and transient immunity per IEC 61000-4. Typical applications include industrial PLC digital outputs, 24 V solenoid and valve drivers, LED indication and lighting strips, relay replacement in HVAC and building automation, and ground-switched load management in process control panels. Each channel independently drives resistive, inductive, or capacitive loads including incandescent lamps with inrush currents well above the steady-state rating. When designing with the ITS716GFUMA1, ensure a 100 nF ceramic bypass capacitor on Vbb close to the IC and adequate PCB copper under the exposed pad for thermal dissipation. The diagnostic feedback pin requires a pull-up resistor to the microcontroller supply; software must debounce fault events because inrush loads (e.g., incandescent lamps) momentarily exceed the current-limit threshold and trip fault flags. This page synthesizes distributor pricing, drop-in same-brand alternatives, and practical design notes not found in the manufacturer datasheet, structured for both human review and AI-search citation.
ITS724GFUMA1 - 4-Ch 3A Smart High-Side Switch | Infineon
The Infineon ITS724GFUMA1 is a 4-channel high-side vertical power MOSFET switch rated at 3.3 A continuous per channel, integrating charge pump, CMOS-compatible ground-referenced inputs, diagnostic feedback and overvoltage protection in Infineon's Smart SIPMOS technology, housed in a 20-pin PG-DSO-20-32 surface-mount package. Designed for 12 V and 24 V industrial DC loads, the device operates across a -10 V to 16 V supply range and provides embedded protective functions including current limiting, overtemperature shutdown, and load-dump protection with external resistor. The monolithic integration eliminates the need for discrete fuses, relays and protection circuitry. A smart high-side switch is a semiconductor relay used in industrial automation and automotive electronics to switch DC loads (solenoids, lamps, motors, valves) on the positive supply rail while providing diagnostic feedback to the microcontroller. The high-side topology allows the load to be grounded, simplifying wiring harness design and improving short-to-ground detection. As a member of Infineon's PROFET (Protected MOSFET) family, the ITS724G is part of the broader category of protected switches that sit between the system power management IC and the final power distribution stage. Key features of the ITS724GFUMA1 include four independently controlled 3.3 A channels with 65 mΩ typical on-resistance per channel, open-drain status flag output for fault reporting, and an integrated charge pump that drives the gate of the N-channel power MOSFET. The device supports PWM operation for dimming or speed control and tolerates high inrush currents typical of incandescent lamp and motor loads. Reverse battery protection is provided by the inherent body diode configuration, and the device is qualified to JEDEC standards for industrial temperature ranges. Typical applications include 24 V industrial PLC output modules, automotive body electronics (door locks, window lifters, seat controllers), process control valve drivers, and LED driver modules. The wide operating voltage window and built-in diagnostics make it well suited for IEC 61131-2 compliant industrial control equipment and Profibus/CAN-connected distributed I/O. When designing with the ITS724G, derate output current according to the JEDEC EIA/JESD51 4-layer board thermal model - the PG-DSO-20-32 package has a junction-to-ambient thermal resistance in the 65-85 C/W range that limits continuous current at elevated ambient temperatures. Always connect the diagnostic status pin to a pull-up resistor and decouple the Vbb supply with at least 100 nF placed within 5 mm of the IC pins.
IW3616 - 12W Dimmable LED Driver IC | Renesas/Dialog
The Renesas (formerly Dialog Semiconductor / iWatt) IW3616 is a two-stage AC/DC digital power controller designed for high-power-factor dimmable LED drivers up to 12W. It combines power factor correction (>0.95), low total harmonic distortion (<15%), and low output ripple (<20%) in a SOIC-14 package, targeting residential and commercial dimmable retrofit LED luminaires. The IW3616-00 and IW3616-01 variants share the same silicon and footprint, with minor firmware mapping differences for dimmer compatibility. An AC/DC LED driver controller is a power management IC that converts mains AC voltage into a regulated DC current suitable for driving high-brightness LEDs. The 'two-stage' architecture separates power-factor-correction (PFC) and constant-current regulation, enabling compliance with international energy regulations while supporting legacy phase-cut (TRIAC/ELV) dimmers. Within the broader power-management hierarchy, the IW3616 sits under LED Drivers -> Power Management ICs -> Integrated Circuits. Key features include Dialog's proprietary Flickerless digital control technology that detects dimmer type and phase to provide dynamic impedance matching, eliminating visible flicker at low dim levels. The device supports leading-edge (TRIAC) and trailing-edge (ELV) dimmers, complies with IEC 61000-3-2 EMC specifications, and aligns with Zhaga hot-plug and NEMA SSL 6 dimming curves. Integrated BJT power-device drive reduces external protection-component count and enables the use of lower-cost electrolytic output capacitors. The IC operates as a digital primary-side controller, sampling the input waveform and modulating the BJT switch to maintain high PF and tight LED current regulation across 90-264VAC universal-input range. Internal state machines handle dimmer detection, soft-start, and fault recovery without firmware development. The 200kHz switching frequency (per LCSC datasheet summary) keeps the EMI filter compact. Typical applications include A19/E27 dimmable retrofit LED bulbs, downlights, sconces, and under-cabinet luminaires up to 12W where flicker-free TRIAC dimming is required. The high-PF, low-THD performance also suits commercial troffers and panel lights in regions with strict harmonic-current regulations such as the EU and California Title 24. Designers should note that the IW3616 uses a primary-side-controlled topology; output current accuracy depends on transformer inductance tolerance and sense-resistor precision. Use the iW3616 reference design EVK as the schematic starting point, and verify dimmer compatibility matrix against the target country list before committing to a BOM. This page synthesizes distributor pricing from LCSC and Mouser, drop-in family variants, and practical dimmer-compatibility notes not consolidated on the OEM product page.
IW3616-01 - Flickerless 12W High-PF Off-Line LED Driver | Renesas
The Renesas (formerly Dialog Semiconductor) IW3616-01 is a two-stage, solid-state lighting (SSL) AC/DC off-line LED driver controller that combines high power factor (>0.95), low total harmonic distortion (<15%), and low output ripple (<20%) for dimmable LED retrofit luminaires up to 12 W. Housed in a 14-pin SOIC package, the device uses a BJT power switch architecture that reduces external protection components and supports lower-cost electrolytic output capacitors compared to MOSFET-based solutions. An LED driver is an AC/DC or DC/DC power converter that delivers a regulated constant current to a string of LEDs, ensuring consistent luminance and protecting the LEDs from line-voltage transients. Two-stage architectures use a power-factor-correction (PFC) front end followed by an isolated or non-isolated DC/DC stage, which separates the high-frequency energy storage from the dimming interface. The iW3616 sits within the broader power management IC hierarchy: LED driver -> AC/DC controller -> power management IC -> semiconductor. Key features of the IW3616-01 include flickerless dimming with both leading-edge (TRIAC) and trailing-edge (ELV) dimmer detection, IEC 61000-3-2 EMC compliance, Zhaga hot-plug interface compatibility, NEMA SSL 6 dimming curve mapping, and integrated protection (LED open-circuit, short-circuit, over-temperature, and over-voltage). The 200 kHz PWM switching frequency keeps the magnetic footprint small for compact lamp form factors. The iW3616-01 applies advanced digital control to detect the dimmer type and phase angle, providing dynamic impedance to interface the dimmer and control LED brightness simultaneously. By using a BJT power device instead of a MOSFET, it reduces component count in protection circuits and enables lower-cost electrolytic capacitor usage, making it attractive for cost-sensitive residential and commercial retrofit bulb designs. Typical applications include dimmable A19/E26/E27 retrofit bulbs, downlights, candelabras, and commercial troffers where flicker-free operation across a wide dimming range is mandatory. The high-PF and low-THD characteristics also make it suitable for regions enforcing strict harmonic current regulations such as the EU, California Title 24, and Energy Star requirements. When designing with the IW3616-01, use the manufacturer's reference design to select the input bulk capacitor, BJT switch, and snubber components, and follow the layout guidelines to keep the high-current loop area small for EMI compliance.
IXCP10M90S - 900V 100mA Switchable Current Regulator | IXYS
The IXYS IXCP10M90S is a 900V minimum breakdown, 1mA to 100mA switchable current regulator housed in an industry-standard JEDEC TO-220-3 package, delivering 40W of continuous power dissipation. It combines a high-voltage current source with an integrated on/off control pin (gate) that allows the current output to be switched by applying a negative voltage to the control terminal, while a resistor between the negative terminal and ground programs the regulated current setpoint. A current regulator is a two-terminal (or three-terminal when controllable) semiconductor that maintains a constant output current over a wide range of applied voltage and temperature. Unlike a series voltage regulator, a current regulator is placed in series with the load to enforce a defined current, making it ideal for high-impedance circuits, current references, and protection stages. The IXCP10M90S belongs to the linear regulator family, specifically the constant-current subset, and is closely related to current limiting diodes (CLDs) but with the added advantage of programmable current and electronic switching. Key features include 900V minimum breakdown voltage (protecting against high-voltage transients), 1mA to 100mA programmable current range via external resistor, low temperature coefficient achieved through threshold compensation, 40W continuous dissipation, and the integrated gate control pin for on/off switching. The JEDEC TO-220 outline ensures compatibility with standard heatsink hardware, while the S-class designation refers to IXYS' enhanced switchable current regulator family. Architecturally, the IXCP10M90S uses a high-voltage bipolar JFET process with on-chip threshold compensation, yielding a temperature-stable current source. The control pin functions as a JFET gate; applying a negative bias below the pinch-off threshold disables current flow, while leaving the pin open or tied high enables normal operation. This design enables fast on/off switching without breaking the high-voltage path. Typical applications include start-up circuits for switch-mode power supplies, PABX current sources and line terminations, highly stable voltage references, surge limiters and voltage protection, fast-acting non-destructive fuses, and biasing networks for high-voltage sensor arrays. Industrial 24V loop-powered instrumentation also benefits from its wide compliance range. Designers should size the heatsink for worst-case continuous dissipation, observe the 900V breakdown derating over temperature, and add a TVS across the device when used in inductive circuits to clamp turn-off transients. Bypass the gate pin with a small capacitor to improve noise immunity in electrically noisy environments. This page synthesizes IXCP10M90S distributor pricing, drop-in alternatives from the IXYS S-class family, and practical design notes not consolidated in the manufacturer datasheet alone.
IXDD609SI - 9A Low-Side Ultrafast MOSFET/IGBT Gate Driver | IXYS
The IXYS IXDD609SI is a 9A peak source/sink low-side gate driver IC in an 8-pin SOIC with an exposed pad (8-SOIC-EP), configured as a non-inverting driver with an enable input. It operates from a wide 4.5V to 35V supply, supports logic inputs that withstand negative swings down to -5V, and produces rise/fall times below 25ns, making it one of the fastest high-current gate drivers in its class. It is pin-compatible with the IXDI609SI (inverting) and IXDN609SI (non-inverting, no enable) variants and is AEC-Q100 qualified for automotive use. A low-side gate driver is a power-management IC that sits between a low-power control signal (from a microcontroller, DSP, or FPGA) and the gate of a power MOSFET or IGBT. The driver's job is to source and sink large peak currents (here, 9A) so that the gate capacitance charges and discharges as quickly as possible. Faster gate transitions directly reduce switching losses, shrink the dead-time needed between complementary switches, and shrink the size of the magnetic components that follow. The IXDD609SI belongs to the gate-driver sub-category of power-management ICs, sitting hierarchically below MOSFETs/IGBTs but above simple logic-level translators in the system signal chain. Key features include 9A peak source/sink drive, 4.5V-35V operating range, <25ns rise/fall times with 1nF load, matched propagation delays, CMOS-compatible input with negative-input swing tolerance, and an enable pin for sequencing. The exposed thermal pad keeps junction temperature manageable at sustained high switching frequencies, and proprietary cross-conduction/shoot-through protection prevents both output stages from turning on simultaneously. The device is built on a high-speed bipolar-CMOS-DMOS process that combines low on-resistance output stages with a CMOS front end. This gives the IXDD609SI its hallmark combination of very high di/dt capability and very low quiescent current, plus latch-up immunity that lets the input sit at large negative voltages without damaging the IC. Typical applications include driving large MOSFETs and IGBTs in motor drives, three-phase inverters, switch-mode power supplies (SMPS), class-D audio amplifiers, and DC-DC converter synchronous-rectifier stages. The wide operating range and AEC-Q100 qualification also make it a strong fit for 24V industrial buses and 12V/24V automotive systems including electric power steering and onboard chargers. When designing with this part, place the IXDD609SI within 1-2 cm of the gate it drives to minimize the gate-loop inductance; use a 1uF low-ESR ceramic bypass capacitor right on the VCC pin, and respect the SOA of the driver when driving very large gate charges (Qg > 100 nC) at high frequency to avoid thermal shutdown. This page synthesizes distributor pricing, drop-in alternatives from IXYS's own IXD_609 family, and practical thermal/layout notes beyond what the manufacturer datasheet alone provides.