集積回路

PIC16F15224-I/P

PIC16F15224-I/P - 8-bit MCU 7KB Flash 32MHz 14-PDIP | Microchip

The Microchip Technology PIC16F15224-I/P is an 8-bit PIC microcontroller built on the Enhanced Mid-Range core with 49 instructions and 16 stack levels, delivering up to 32 MHz CPU performance from a 7 KB (4K x 14) self-read/write Flash program memory, 512 bytes SRAM, and 128 bytes data EEPROM, housed in a 14-pin PDIP through-hole package. Functional-safety (FuSa) variants are supported in the family for safety-critical designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, volatile data RAM, and a peripheral set (timers, ADC, communication, GPIO) into one package. The PIC16F152xx family is positioned as an Enhanced Mid-Range device within Microchip's PIC16 portfolio (PIC16 -> 8-bit MCU -> MCU -> semiconductor), pairing the standard PIC16 instruction set with Core Independent Peripherals (CIPs) and Intelligent Analog peripherals. Compared with the older baseline PIC16, the Enhanced Mid-Range core adds more instructions, deeper stack, and improved interrupt handling while maintaining code compatibility with classic PIC16F mid-range code where appropriate. Key features include 12 I/O pins, a 10-bit ADC, two PWM modules, two CCP modules, hardware limit timer (HLT), watchdog timer (WDT), Peripheral Pin Select (PPS) for flexible signal routing, EUSART, MSSP (SPI/I2C), and eXtreme Low-Power (XLP) Sleep mode. The device operates from 1.8 V to 5.5 V with self-read/write Flash that supports in-application firmware updates. CIPs such as the configurable logic cell and signal measurement timer reduce CPU overhead, allowing the MCU to handle sensor interfacing, motor timing, and communication deterministically without software intervention. Typical applications include cost-sensitive sensor nodes, home appliances, lighting control, battery-powered IoT endpoints, and low-end motor control. The wide 1.8 V to 5.5 V supply range and XLP Sleep current make it suitable for energy-harvesting and battery-backed designs. PPS allows designers to remap peripherals to any I/O pin, simplifying PCB routing and enabling PCB layout reuse across family variants in 8-pin SOIC, 14-pin PDIP/SOIC, and 20-pin packages. A key design tip is to keep VDD decoupling within 5 mm of the supply pins and tie all unused pins to defined logic levels (VSS or VDD) to minimize I/O leakage. PPS remapping should be locked early in firmware to avoid unintended peripheral shifts at runtime. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

見積もりお問い合わせ

PIC16F15224-I/ST

PIC16F15224-I/ST - 8-bit MCU 7KB Flash 32MHz TSSOP-14 | Microchip

The Microchip PIC16F15224-I/ST is an 8-bit RISC microcontroller featuring a 32 MHz PIC16F152 CPU core and 7 KB Flash program memory, housed in a 14-pin TSSOP (ST) package. The device operates from 2.5V to 5.5V with 12 I/O lines, integrated 10-bit ADC, dual PWM channels, dual CCP modules, and standard communication peripherals including EUSART, SPI, and I2C. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path that combines a CPU, RAM, Flash program memory, and peripherals on one die. Within the embedded system hierarchy, an MCU sits above discrete logic but below more capable 32-bit microprocessors; it is the workhorse of cost-sensitive sensor and real-time control applications where deterministic behavior, low power, and small package size matter more than raw compute. The PIC16F15224 belongs to Microchip's PIC16F152xx family, an enhanced mid-range core featuring 49 instructions, 16 stack levels, and Core Independent Peripherals (CIPs). Key features include eXtreme Low-Power (XLP) Sleep mode for battery-powered designs, Peripheral Pin Select (PPS) for flexible pin routing, an HLT (Hardware Limit Timer) peripheral, and on-chip debugging support. The Flash memory supports self read/write capability, enabling field firmware updates. The 32 MHz internal oscillator eliminates the need for an external crystal in most designs, reducing BOM cost and PCB footprint. Typical applications include IoT sensor nodes, white goods and appliance control, low-cost motor control, LED lighting drivers, and battery-powered portable devices. The wide 2.5V-5.5V supply range supports direct connection to single-cell Li-ion, two-cell AA, or 3.3V/5V regulated rails. The 14-pin TSSOP footprint balances I/O count with compact board area. When designing with this MCU, allocate sufficient decoupling (100 nF + 1 uF) near VDD pins and verify unused I/O pins are configured as outputs or inputs with internal pull-ups to minimize current leakage. The MCLR pin should be tied to VDD through a 10 kohm resistor unless in-circuit debugging is required. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

見積もりお問い合わせ

PIC16F15225-E/SL

PIC16F15225-E/SL - 14KB Flash 8-bit MCU, 32MHz | Microchip

The Microchip Technology PIC16F15225-E/SL is a 14-pin 8-bit PIC microcontroller from the PIC16F152xx family, featuring an enhanced mid-range core with 49 instructions, 16 stack levels, and self read/write FLASH. It integrates 14KB (8K x 14) of program FLASH, 1KB of RAM, and is housed in a 14-pin SOIC package. The CPU operates at up to 32MHz with 8-bit data path and supports an industrial -40C to +125C operating temperature range (denoted by the -E suffix). What is a PIC16F152xx MCU? The PIC16F152xx is an Enhanced Mid-Range 8-bit microcontroller family from Microchip that combines Core Independent Peripherals (CIPs), intelligent analog blocks, and standard communication modules with eXtreme Low Power (XLP) Sleep mode. In the system hierarchy, it belongs to: microcontroller > MCU > 8-bit PIC > enhanced mid-range core > CMOS microcontroller > semiconductor IC. The PIC architecture is widely deployed in consumer, industrial, IoT edge-node, and motor-control applications where deterministic behavior, low power, and small pin counts are priorities. Key features of the PIC16F15225-E/SL include a 10-bit ADC with up to 9 input channels, two PWM channels, two CCP modules, a Hardware Limit Timer (HLT), Watchdog Timer (WDT), Peripheral Pin Select (PPS), EUSART (UART), and an MSSP module supporting both SPI and I2C. The device integrates 11 general-purpose I/O pins. The 14KB FLASH enables substantial application code, while the 1KB RAM supports data buffering and stack-intensive operations across 16 stack levels. The PIC16F15225 uses an enhanced mid-range 8-bit RISC core with hardware multiplier and a 32MHz internal oscillator, eliminating the need for an external crystal in most designs. The 10-bit ADC delivers up to 9 channels of analog conversion, while dual PWM/CCP channels simplify motor control, lighting, or power-conversion loops. PPS remaps digital peripherals to multiple I/O pins, easing PCB layout. Together with XLP Sleep, the part targets battery-powered and always-on sensor products. Typical applications include low-power IoT sensor nodes, consumer appliance control, LED lighting controllers, battery management peripherals, and small home-automation hubs. The compact 14-pin SOIC footprint suits space-constrained designs and surface-mount manufacturing. When designing with this part, leverage the Peripheral Pin Select (PPS) module to remap EUSART, MSSP, and PWM outputs to the most convenient package pins, and rely on the XLP Sleep mode to extend battery life in always-on edge nodes. Refer to the manufacturer datasheet for full electrical characteristics and programming specifications.

見積もりお問い合わせ

PIC16F15225-I/MG

PIC16F15225-I/MG - 8-bit MCU, 14KB Flash, 32MHz, 16-QFN | Microchip

The Microchip Technology PIC16F15225-I/MG is an 8-bit PIC microcontroller built on the Enhanced Mid-Range core running at up to 32MHz, with 14KB (8K x 14 words) of self-read/write Flash program memory and 1KB of RAM, packaged in a compact 16-pin QFN (3x3 mm, MG package). It belongs to the PIC16F152xx family, which combines Core Independent Peripherals (CIPs) such as 2x CCP and 2x PWM with intelligent analog (10-bit ADC) and standard serial interfaces (EUSART, SPI, I2C via MSSP) for sensor and motor-driven embedded designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, data RAM, and peripheral interfaces. In the broader hierarchy, an MCU is a subset of microprocessors specialized for embedded control. The 8-bit class targets cost-sensitive, deterministic, low-power applications such as appliance controls, sensor hubs, IoT endpoints, and battery-powered devices where 32-bit performance is unnecessary. The PIC16F15225's eXtreme Low Power (XLP) Sleep mode and Peripheral Pin Select (PPS) routing fit this exact use-case profile. Key differentiating features of this PIC16F15225 variant include 14KB Flash with self read/write capability, 1KB RAM, 10-bit ADC, 2 CCP (Capture/Compare/PWM) channels, 2 dedicated PWM channels, EUSART, MSSP (SPI/I2C), and XLP Sleep mode. According to the Microchip datasheet, the device delivers 49 instructions with 16 stack levels and supports in-circuit serial programming for production-line firmware updates. At the architecture level, the PIC16F15225 uses a Harvard RISC core with a 14-bit instruction word, 16 levels of hardware stack, and a flexible oscillator block supporting internal 32MHz HFINTOSC without external crystals. Peripheral Pin Select remaps digital peripheral I/O to multiple pins, simplifying PCB routing and enabling smaller 16-QFN layouts. Typical applications include home-appliance control boards, low-power IoT sensor nodes, LED lighting drivers with PWM dimming, battery chargers, fan controllers, and small consumer electronics. The compact 3x3 mm QFN footprint suits space-constrained designs such as wearable bands and portable medical accessories. Designers should note that PIC16F15225 is the 16-pin, 14KB-Flash variant in the family. Larger-memory and higher-pin-count siblings (e.g., PIC16F15244, PIC16F15245) share the same peripheral set but require different packages. Programming is supported through MPLAB X IDE and XC8 compiler, and the MPLAB Code Configurator generates driver code for ADC, PWM, EUSART, MSSP, and PPS in seconds. This page synthesizes real-time distributor pricing from DigiKey and Mouser, parametric drop-in alternatives drawn from Microchip's PIC16F152xx family and cross-brand Cortex-M0 equivalents, plus practical design notes covering XLP Sleep current, ADC acquisition timing, and QFN PCB layout that you will not find aggregated on any single manufacturer page.

見積もりお問い合わせ

PIC16F15225-I/SL

PIC16F15225-I/SL - 14KB Flash 8-bit MCU 32MHz | Microchip

The Microchip Technology PIC16F15225-I/SL is an 8-bit PIC microcontroller featuring a 32 MHz CPU, 14 KB of Flash program memory, and 1 KB of data RAM, housed in a 14-pin SOIC (SL) package. The "I" suffix denotes the industrial -40C to +85C operating temperature range, and the SL suffix indicates the 14-pin narrow-body small-outline IC package. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (typically Flash), volatile data RAM, and a set of on-chip peripherals around an 8-bit data path. PIC microcontrollers use a RISC-style Harvard architecture and are the dominant 8-bit platform for cost-sensitive embedded control, sitting at the bottom of the MCU hierarchy: MCU -> 8-bit MCU -> PIC -> PIC16 family -> PIC16F152xx sub-family. Core Independent Peripherals (CIPs) offload tasks such as waveform generation and signal conditioning from the CPU, enabling deterministic real-time behavior without software intervention. Key features of the PIC16F15225 include a 10-bit ADC with computation, two PWM modules, two Capture/Compare/PWM (CCP) peripherals, Peripheral Pin Select (PPS) for flexible I/O mapping, hardware EUSART plus SPI and I2C communication, a Windowed Watchdog Timer (WWDT), and eXtreme Low-Power (XLP) Sleep mode. PPS allows designers to remap digital peripherals to most I/O pins, simplifying PCB layout. The XLP Sleep mode supports battery-powered applications with nanoampere quiescent currents. Typical applications include sensor node interfaces, low-cost motor control, LED lighting controllers, battery-powered IoT endpoints, and home appliances. Industrial-grade -40C to +85C operation allows use in uncontrolled-temperature environments. When designing with this MCU, ensure that the on-chip debug and programming pins (ICSPCLK/ICSPDAT) are accessible for in-circuit serial programming, and place a 100 nF decoupling capacitor as close as possible to the VDD pin. PPS should be configured early in firmware to avoid peripheral pin mapping conflicts.

見積もりお問い合わせ

PIC16F15225-I/ST

PIC16F15225-I/ST - 14KB Flash 8-bit MCU, 32MHz, TSSOP-14 | Microchip

The Microchip Technology PIC16F15225-I/ST is an 8-bit PIC microcontroller from the PIC16F152xx family, integrating 14KB Flash program memory, 1KB RAM, and a 10-bit ADC in a 14-pin TSSOP package. It features a 32MHz internal oscillator, two PWM modules, two CCP modules, hardware limit timer, watchdog timer, peripheral pin select (PPS), EUSART, MSSP (SPI/I2C), and eXtreme Low-Power (XLP) Sleep mode. A PIC16F152xx microcontroller is an 8-bit CMOS flash-based MCU built on an enhanced mid-range core with 49 instructions, 16 stack levels, and self read/write capability on program memory. It belongs to the broader PIC16F family of microcontrollers, which itself sits within the hierarchy of microcontrollers -> microprocessors -> integrated circuits -> semiconductors. The enhanced mid-range architecture balances code density, deterministic interrupt response, and ultra-low power consumption, making this class of MCU well suited to cost-sensitive embedded applications. Key features include eXtreme Low-Power (XLP) Sleep mode that reduces quiescent current to nanoampere levels, Peripheral Pin Select (PPS) which allows flexible remapping of digital peripherals to I/O pins, and Core Independent Peripherals (CIPs) that offload tasks from the CPU. The MSSP module supports both SPI and I2C master/slave, while EUSART handles asynchronous and synchronous serial communication. Intelligent Analog features include a 10-bit ADC and dual comparators. The device operates across 1.8V to 5.5V supply and is available in industrial temperature grade (-40C to +85C). Typical applications include low-power IoT sensor nodes, battery-powered home automation, consumer electronics human-machine interfaces, HVAC thermostat controls, motor control for small BLDC fans, and LED lighting controllers. The 14-pin TSSOP footprint is attractive for compact PCB designs where board area is constrained. When designing with this part, evaluate the 12 I/O pins carefully against peripheral needs: PPS allows most peripherals to be remapped, but pin count remains the hard constraint. The XLP Sleep current specification should be verified against the application's duty cycle to confirm battery-life targets. A 1.8V minimum VDD supports single-cell alkaline or coin-cell battery operation directly. This page synthesizes distributor pricing, drop-in alternatives sourced from the PIC16F152xx family, and practical design notes not found in the manufacturer datasheet alone.

見積もりお問い合わせ

PIC16F15225T-I/ST

PIC16F15225T-I/ST - 8-Bit MCU, 14KB Flash, 32MHz, 14-TSSOP | Microchip

The Microchip Technology PIC16F15225T-I/ST is an 8-bit PIC microcontroller from the PIC16F152xx family, integrating 14 KB (8K x 14 words) of Flash program memory and 1 KB of RAM in a 14-pin TSSOP package. It operates at up to 32 MHz, includes a 10-bit ADC, two PWM channels, two CCP modules, an EUSART, and SPI/I2C peripherals, and supports the Peripheral Pin Select (PPS) feature for flexible signal routing. An 8-bit microcontroller (MCU) is a microprocessor with an 8-bit data path, optimized for embedded control tasks where deterministic behavior, low power, and small footprint outweigh the need for raw compute. Within the broader taxonomy, a PIC16F15225 belongs to the PIC16 family, then the 8-bit MCU class, then the microcontroller category, then the integrated circuit family, then the semiconductor hierarchy. 8-bit MCUs typically include an on-chip CPU, Flash program memory, SRAM, EEPROM (or data Flash), and a mix of timers, ADC, communication peripherals, and digital I/O - forming a complete compute node for sensor reading, actuator driving, and protocol bridging. Key features of the PIC16F15225T-I/ST include Core Independent Peripherals (CIPs) such as the Configurable Logic Cell (CLC) and Numerically Controlled Oscillator (NCO), Intelligent Analog (10-bit ADC with computation), and standard communication peripherals (EUSART, SPI, I2C). The device supports eXtreme Low-Power (XLP) Sleep modes for battery applications, a Windowed Watchdog Timer (WWDT) for safety-critical firmware, and Hardware Limit Timer (HLT) for robust fault recovery. Architecturally, the PIC16F15225 uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word, supporting up to 49 instructions including hardware multiply. The 32 MHz internal oscillator provides system clock without external components, while PPS allows digital peripheral I/O mapping, simplifying PCB routing. The TSSOP-14 package is among the smallest in the family, suitable for space-constrained designs. Typical applications include low-power IoT sensor nodes, battery-operated home automation devices, consumer white goods user interfaces, LED lighting controllers, simple motor control, and portable medical peripherals. The combination of small package, low power, and a rich peripheral set makes the PIC16F15225T-I/ST well suited for cost-sensitive embedded products. When designing with this MCU, pay attention to the Vdd range (1.8V to 5.5V), the ICSP programming pinout, and the proper decoupling scheme. In-circuit serial programming requires specific pin assignments - use the ICSP pinout in the datasheet and not the TSSOP mechanical pin numbering. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

見積もりお問い合わせ

PIC16F15243-E/P

PIC16F15243-E/P - 8-bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip Technology PIC16F15243-E/P is a member of the PIC16F152xx 8-bit microcontroller family that delivers essential Core Independent Peripherals (CIPs), intelligent analog, and standard communication modules in a 20-pin PDIP package. It integrates 3.5KB (2K x 14) of self-read/write Flash program memory and 256 bytes of SRAM, runs at a maximum 32 MHz internal oscillator, and supports eXtreme Low-Power (XLP) sleep modes. A microcontroller (MCU) is a single-chip computer that combines a CPU core, non-volatile program memory, RAM, and a set of on-chip peripherals such as timers, ADCs, and communication interfaces. PIC microcontrollers use a RISC-based Harvard architecture; the PIC16F152xx family extends the enhanced mid-range core with 49 instructions, 16 stack levels, peripheral pin select (PPS) remapping, and a functional-safety-capable design pattern. The PIC16F15243-E/P specifically targets applications that need this baseline at minimum cost. Key features include one 10-bit ADC, two PWM channels, two CCP modules, hardware limiting timer (HLT), windowed watchdog timer (WDT), PPS, EUSART, and MSSP supporting SPI/I2C. The wide 1.8V-5.5V supply range permits direct operation from a single Li-ion cell or 5V regulated rail, while XLP sleep enables nanoWatt standby for battery-backed nodes. The device uses an enhanced mid-range 8-bit core with self-programmable Flash, ICD debugging support, and a vectored interrupt controller. Compared with the older PIC16F1xx baseline, the 15243 adds PPS routing, an on-chip 32 MHz HFINTOSC with hardware limiting, and faster ADC acquisition, reducing external component count in sensor and motor-control designs. Typical applications include consumer appliance control, low-cost sensor nodes, LED lighting controllers, battery-powered IoT edge devices, and PIC16F45 pin-compatible upgrades. Industrial segments include HVAC auxiliary controllers and simple human-machine interface boards that do not require USB or CAN. When designing with the PIC16F15243-E/P, ensure MPLAB X IDE and XC8 compiler are used, allocate at least one PPS pin for serial debug, and respect the 5.5V absolute-maximum VDD limit. Decouple VDD with 100nF plus 10uF bulk capacitance placed within 5 mm of the supply pin. This page synthesizes distributor pricing, drop-in PIC16F152xx alternatives, and practical MPLAB/XC8 design notes not found in the standalone datasheet.

見積もりお問い合わせ

PIC16F15243-E/REB

PIC16F15243-E/REB - 8-bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip PIC16F15243-E/REB is an 8-bit microcontroller IC with Functional Safety (FuSa) support, operating at up to 32 MHz, integrating 3.5 KB (2K x 14) of Flash program memory, 256 bytes of SRAM, and housed in a 20-pin VQFN (3x3 mm) package. The -E temperature grade denotes an extended industrial operating range of -40C to +125C. As part of the PIC16F152xx family, this device combines Core Independent Peripherals (CIPs), Intelligent Analog, and standard communication peripherals in an eXtreme Low-Power (XLP) architecture. What is an 8-bit microcontroller? An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, memory, and peripherals on a single die. PIC microcontrollers use a modified Harvard RISC architecture with separate program and data buses. They belong to the broader category of embedded microcontrollers within the semiconductor hierarchy: MCU -> microcontroller -> embedded processor -> semiconductor. The 8-bit class targets cost-sensitive, low-power applications where deterministic real-time behavior and ease of use outweigh raw computational throughput. Key features include 10-bit ADC with computation, 2 PWM modules, 2 CCP (Capture/Compare/PWM), Hardware Limit Timer (HLT), Watchdog Timer (WDT), Peripheral Pin Select (PPS), and communication peripherals EUSART, SPI, and I2C. The XLP Sleep Mode enables nanoWatt-class standby currents for battery-powered designs. PPS allows flexible signal routing, mapping digital peripherals to physical pins in software rather than via fixed silicon multiplexing. The PIC16F15243 employs a 14-bit instruction word with a deep pipeline and a 32 MHz internal oscillator, delivering 8 MIPS throughput. Core Independent Peripherals such as the Hardware Limit Timer and CWG (Complementary Waveform Generator) operate without CPU intervention, enabling deterministic timing and offloading the core. Functional Safety support makes this part attractive for safety-critical applications requiring documentation for IEC 61508 or similar standards. Typical applications include IoT sensor nodes, battery-powered edge devices, automotive body and sensor subsystems, industrial sensor signal conditioning, low-cost motor control, and consumer white goods. The combination of small VQFN-20 footprint, eXtreme Low-Power Sleep, and PPS makes this MCU particularly attractive for space-constrained designs. When designing with this part, leverage PPS to route peripherals to available pins and minimize PCB routing complexity. Choose the -E temperature grade only when the application exceeds +85C ambient; the standard -I grade parts are otherwise functionally identical and generally less expensive. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet alone.

見積もりお問い合わせ

PIC16F15243-E/SO

PIC16F15243-E/SO - 8-bit MCU, 3.5KB Flash, 20-Pin SOIC | Microchip

The Microchip Technology PIC16F15243-E/SO is an 8-bit enhanced mid-range microcontroller from the PIC16F152xx family with 3.5 KB Flash program memory, 256 B RAM, and a 10-bit ADC, packaged in a 20-pin SOIC (SO). It executes instructions at up to 32 MHz and features Core Independent Peripherals (CIPs), Peripheral Pin Select (PPS), and an eXtreme Low-Power (XLP) Sleep mode suitable for battery-powered applications. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (typically Flash), volatile working memory (RAM), and a set of on-chip peripherals into one package. PIC microcontrollers use a Harvard-architecture CPU with a RISC-like instruction set, separating program and data memory buses. Within Microchip's taxonomy, the PIC16F152xx belongs to the enhanced mid-range core family, positioned between the baseline PIC10/12/16 families and the high-performance PIC18 family, and tailored for cost-sensitive sensor and real-time control tasks. Key features of the PIC16F15243 include 3.5 KB self-read/write Flash, 16 stack levels, two 10-bit PWMs, two Capture/Compare/PWM (CCP) modules, a Hardware Limit Timer (HLT), Watchdog Timer (WDT), PPS for flexible I/O mapping, EUSART (UART with LIN) and MSSP (SPI/I2C) communication, a 10-bit ADC with internal fixed-voltage reference, and eXtreme Low-Power Sleep mode. The 'E' suffix denotes an extended temperature grade of -40C to +125C. The 20-pin SOIC package gives access to up to 18 general-purpose I/O pins via PPS, and the small outline footprint is suited for hand-soldered prototypes and high-density production boards alike. PPS allows most digital peripherals to be routed to almost any I/O pin, simplifying PCB layout and BOM reuse across the PIC16F152xx family. Combined with CIPs such as the Hardware Limit Timer, the device can service sensors, switches, and communication lines without CPU intervention, freeing the core for application logic. Typical applications include low-power IoT sensor nodes, battery-powered remote controls, LED lighting controllers, white-goods and small-appliance control boards, and LIN-node automotive body electronics using the on-chip EUSART with LIN slave support. Designers value the XLP Sleep mode for multi-year coin-cell lifetimes and the PPS flexibility for layout reuse. When designing with the PIC16F15243-E/SO, leave VDD/VSS decoupling within 5 mm of the pins, configure the Configuration Words for the desired oscillator and WDT behavior, and use PPS to keep high-speed signals (EUSART, MSSP) on adjacent pins to simplify routing. Verify ADC reference selection against the application noise budget, and ensure unused I/O pins are configured as outputs low to minimize Sleep current. This page synthesizes distributor pricing, drop-in same-family alternates, and practical design notes that go beyond the manufacturer datasheet summary, helping procurement and design engineers evaluate the PIC16F15243-E/SO for both new designs and as a drop-in swap on existing 20-pin SOIC boards.

見積もりお問い合わせ

PIC16F15243-E/SS

PIC16F15243-E/SS - 8-bit 32MHz 3.5KB Flash MCU 20-SSOP | Microchip

The Microchip Technology PIC16F15243-E/SS is an 8-bit PIC microcontroller with a 32 MHz enhanced mid-range core, 3.5 KB of self-read/write Flash program memory, 256 bytes of RAM, and a 20-pin SSOP package. It is part of the PIC16F152xx family, which integrates core-independent peripherals, intelligent analog, and standard communication modules while supporting eXtreme Low Power (XLP) sleep modes for battery-friendly designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and programmable peripherals on one die. The PIC16 architecture uses a Harvard RISC design with a 14-bit instruction word, and the 16F152xx sub-family specifically adds 49 instructions, 16 stack levels, and a Peripheral Pin Select (PPS) routing fabric. In the system hierarchy this MCU sits inside the 8-bit MCU class, within embedded microcontrollers, inside the broader Integrated Circuits category. Key features include 12 channels of 10-bit ADC, two PWM channels, two CCP modules, a hardware limit timer (HLT), a windowed watchdog timer (WDT), PPS, an EUSART (UART with LIN), an MSSP module that handles both SPI and I2C (master/slave), and a clock out function. The -E/SS suffix designates the -40C to +125C extended operating temperature range in a 20-pin SSOP package. Typical applications include functional-safety sensor nodes, low-power IoT edge devices, appliance user-interface controllers, LED lighting control, and general-purpose 8-bit embedded logic replacement. Functional-safety customers (FuSa) particularly value the documentation package and core-independent peripherals that simplify deterministic loop design. Design consideration: because this part uses PPS, every peripheral signal can be remapped to most digital I/O pins, but only one signal can occupy a pin at a time - always check the PPS assignment table when porting code between 14-pin and 20-pin PIC16F152xx variants. The 20-SSOP footprint is industry-standard and reflow-compatible with Pb-free profiles. This page synthesizes current distributor stock, drop-in same-package alternatives, and practical design notes that go beyond the manufacturer datasheet introduction, helping engineers select the right 8-bit MCU for low-power embedded designs.

見積もりお問い合わせ

PIC16F15243-I/REB

PIC16F15243-I/REB - 8-bit 32MHz MCU, 3.5KB Flash, 20-VQFN | Microchip

The Microchip Technology PIC16F15243-I/REB is an 8-bit PIC microcontroller with a 32MHz CPU, 3.5KB (2K x 14) Flash program memory, 256B RAM, and 10-bit ADC, housed in a 20-pin VQFN (3x3 mm) package. It targets Functional Safety (FuSa) applications with on-chip Core Independent Peripherals (CIPs), two PWM/CCP modules, EUSART, SPI/I2C, and an eXtreme Low-Power (XLP) sleep mode. What is a PIC16 8-bit microcontroller? A PIC16F microcontroller is a low-power, mid-performance 8-bit RISC MCU family from Microchip built on a Harvard architecture with separate program and data buses. The PIC16F152xx sub-family adds Core Independent Peripherals (CIPs) - hardware state machines that run without CPU intervention - and Intelligent Analog on-chip peripherals, sitting in the power-management and embedded control hierarchy between simple 8-bit MCUs and 32-bit Cortex-M parts. Key features include 32MHz internal oscillator operation, 3.5KB Flash self-programmable memory, hardware PPS (Peripheral Pin Select), Hardware Limit Timer (HLT), Windowed Watchdog Timer (WDT), and the XLP sleep mode with nanoWatt leakage. The 20-VQFN package has an exposed thermal pad and a compact 3x3 mm footprint suitable for space-constrained PCB designs. Peripherals include a 10-bit ADC with Computation (ADC2) for automated averaging and threshold comparison. Typical applications include sensor nodes, IoT edge devices, battery-powered instruments, appliance controls, lighting ballasts, and safety-capable embedded subsystems. The Functional Safety documentation and FMEDA support enable integration into IEC 61508 SIL 2 designs when paired with a safety manual and proper diagnostic coverage at the system level. When designing with this device, allocate pins carefully because PPS lets most digital peripherals be remapped to multiple I/O pins. Ensure decoupling capacitors are placed within 3mm of VDD and VSS. Use the ADC2 Computation mode for oversampling to reduce software overhead in sensor acquisition loops. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the standalone Microchip datasheet. Pin-compatible variants in PDIP, SOIC, SSOP, and TSSOP packages are listed in the alternatives section for PCB layout reuse.

見積もりお問い合わせ

PIC16F15243-I/SS

PIC16F15243-I/SS - 8-bit MCU, 3.5KB Flash, 20-SSOP | Microchip

The Microchip Technology PIC16F15243-I/SS is an 8-bit PIC16 microcontroller from the PIC16F152xx low pin count family, delivering 32 MHz CPU performance from 3.5 KB (2K x 14) of self-programmable Flash program memory and 256 bytes of SRAM in a 20-pin SSOP package. The -I suffix indicates the industrial temperature grade (-40C to +85C). Functional safety (FuSa) support and core-independent peripherals (CIPs) make this part suitable for safety-critical and real-time control applications. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, programmable I/O peripherals, and often communication interfaces and analog blocks. The PIC16 family uses a RISC-based 8-bit core with a modified Harvard architecture, where program and data buses are separate to allow simultaneous instruction fetch and data access. Within the broader taxonomy, an MCU belongs to embedded microcontrollers -> microcontrollers -> integrated circuits -> semiconductors. Key features of the PIC16F15243 include a 10-bit ADC with up to 12 input channels, two 10-bit PWMs, two CCP modules, Peripheral Pin Select (PPS) for flexible signal routing, EUSART plus SPI and I2C communication, hardware limit timer (HLT), windowed watchdog timer (WDT), and eXtreme Low-Power (XLP) Sleep modes for battery-powered designs. The FuSa-ready architecture supports functional safety documentation required by IEC 61508 and similar standards. The PIC16F15243 architecture integrates a 10-bit ADC with Device Information Area (DIA) calibration for offset compensation, plus a Fixed Voltage Reference (FVR) to enhance ADC accuracy. PPS allows remapping of digital peripherals to multiple I/O pins, simplifying PCB routing. The Memory Access Partition (MAP) supports bootloader and data protection schemes, while the eXtreme Low-Power Sleep mode delivers nanoamp-level standby current for energy harvesting applications. Typical applications include low-cost sensor nodes, battery-powered IoT end devices, appliance control boards, LED lighting drivers, HVAC fan controllers, and consumer electronics requiring functional safety features. PPS flexibility is particularly valuable when designers must route SPI or I2C signals to alternate pins to simplify board layout. When designing with this device, ensure your programmer/debugger supports the PIC16F152xx device ID. Microchip's MPLAB X IDE with XC8 compiler and the PICkit 5 or SNAP debugger are typical toolchains. Always review the latest family datasheet for electrical specifications before committing to production layouts. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet - enabling faster design decisions for engineers evaluating the PIC16F15243-I/SS for sensor and real-time control applications.

見積もりお問い合わせ

PIC16F15243T-I/REB

PIC16F15243T-I/REB - 8-bit MCU, 3.5KB Flash, 32MHz, 20-VQFN | Microchip

The Microchip PIC16F15243T-I/REB is an 8-bit PIC microcontroller from the PIC16F152xx family, featuring 3.5KB Flash program memory, 256 bytes RAM, and a 32MHz internal core, housed in a 20-pin VQFN (3x3 mm) package. It integrates a 10-bit ADC, two PWM modules, two CCP modules, hardware limit timer (HLT), watchdog timer (WDT), peripheral pin select (PPS), EUSART, SPI/I2C, and eXtreme Low-Power (XLP) Sleep mode, designed for cost-sensitive sensor and real-time control applications. An 8-bit microcontroller (MCU) is a small computer-on-a-chip integrating a CPU, memory (Flash/RAM), and peripherals on a single die. PIC microcontrollers sit within the broader hierarchy of embedded microcontrollers -> microcontrollers -> microprocessors/memory ICs -> integrated circuits -> semiconductors, and are widely used in cost-optimized embedded designs due to their deterministic instruction set and rich peripheral integration. Key features of the PIC16F15243 include Functional Safety (FuSa) support, Core Independent Peripherals (CIPs) for offloading CPU tasks, intelligent analog peripherals, and standard communication modules. The 32MHz operation delivers 8 MIPS instruction throughput, and the XLP Sleep mode enables nanoWatt sleep currents suitable for battery-powered sensor nodes. The 20-VQFN package supports compact board layouts in space-constrained IoT products. Architecturally, the PIC16F15243 uses Microchip's enhanced mid-range core with a 14-bit instruction word, hardware multiplier, and interrupt-driven peripheral integration. The device operates from 1.8V to 5.5V and includes fail-safe clock monitoring for functional safety compliance. PPS allows flexible pin-to-peripheral mapping, simplifying PCB routing and BOM reuse across multiple SKUs in a product family. Typical applications include IoT sensor nodes, home appliance control, LED lighting controllers, battery-powered instruments, and industrial sensor interfaces. The integrated 10-bit ADC and PWM modules also suit closed-loop control tasks such as motor speed control and temperature regulation. When designing with this MCU, ensure the ICSP programming pins are accessible for in-circuit firmware updates, and route the VQFN exposed pad to a continuous ground copper pour for thermal dissipation and EMI performance. This page synthesizes distributor pricing, drop-in alternatives from the PIC16F152xx family, and practical design notes not found in the manufacturer datasheet.

見積もりお問い合わせ

PIC16F15243T-I/SO

PIC16F15243T-I/SO - 8-bit MCU, 3.5KB Flash, 20-SOIC | Microchip

The Microchip Technology PIC16F15243T-I/SO is an 8-bit PIC microcontroller from the PIC16F152xx family, featuring 3.5KB Flash program memory (2K x 14 words), 256 bytes of SRAM, and a 32 MHz CPU core, housed in a 20-pin SOIC package. This tape-and-reel variant ships in industrial temperature grade (-40C to +85C) and supports a wide operating voltage range from 1.8V to 5.5V. The part targets cost-sensitive sensor and real-time control applications where low power and small footprint are essential. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash, RAM, EEPROM), and peripherals on a single silicon die. The PIC architecture uses a Harvard design with separate program and data buses, a RISC instruction set, and deterministic instruction timing. Within the broader hierarchy, an MCU belongs to the category of microcontrollers -> microprocessors -> semiconductors -> integrated circuits. The PIC16F152xx family in particular targets Core Independent Peripherals (CIPs), Intelligent Analog, and standard communication in compact pin-count packages. Key features include a 10-bit Analog-to-Digital Converter (ADC) with internal voltage reference, two PWM modules, two Capture/Compare/PWM (CCP) peripherals, Peripheral Pin Select (PPS) for flexible I/O routing, hardware limit timer (HLT), watchdog timer (WDT), and the standard EUSART plus SPI/I2C communication modules. The XLP (eXtreme Low-Power) Sleep mode with nanowatt-level standby current enables battery-powered sensor applications that must operate for years on a single cell. The PIC16F15243 architecture uses an enhanced mid-range 16-bit instruction word core optimized for C-code efficiency and fast interrupt response. On-chip peripherals are interconnected through the Microchip proprietary CIP bus, allowing the ADC, PWM, and timers to operate without CPU intervention, freeing the core for application logic. Functional Safety (FuSa) features support IEC 61508 SIL-2 capable system designs per the datasheet. Typical applications include IoT sensor nodes, battery-powered wireless remote controls, low-cost home appliances, white goods user interfaces, LED lighting controllers, and small motor-control subsystems. The compact 20-SOIC footprint fits hand-held enclosures and densely populated PCBs. Designers should evaluate RAM headroom (256 bytes is tight for buffered protocols), pick a programming/debug adapter from the PICkit/SNAP/MPLAB ICD family, and follow the datasheet recommended decoupling scheme (typically 100 nF plus 10 uF bulk near VDD). Migration within the PIC16F152xx family is straightforward when scaling memory or peripheral needs. This page synthesizes distributor pricing, drop-in alternatives from the same family, and practical design notes not found in the manufacturer datasheet alone.

見積もりお問い合わせ

PIC16F15244-E/SO

PIC16F15244-E/SO - 8-bit PIC16 MCU, 7KB Flash, SOIC-20 | Microchip

The Microchip Technology PIC16F15244-E/SO is an 8-bit RISC microcontroller built on the PIC16 CPU core with a maximum clock frequency of 32 MHz, packaged in a 20-pin SOIC (SO) wide-body plastic small-outline IC. The device ships with 7.168 KB of self-programmable Flash program memory, 512 bytes of SRAM, and 18 bytes of data EEPROM, addressing cost-sensitive sensor and real-time control designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and a rich set of programmable peripherals. The PIC16F152xx family is positioned inside the broader PIC16 mid-range family (an 8-bit PIC MCU family), itself part of Microchip's 8-bit MCU portfolio that competes with other 8-bit architectures for embedded control. As a Flash-based MCU, the PIC16F15244 supports in-circuit serial programming (ICSP) and field re-programmability, which lowers lifecycle cost for production and field updates. Key features include a 10-bit ADC with multiple channel options, two PWM modules, two CCP (Capture/Compare/PWM) modules, hardware limit timer (HLT), watchdog timer (WDT), peripheral pin select (PPS), EUSART, SPI, and I2C. The device operates from 1.8 V to 5.5 V across an industrial -40 C to +125 C temperature range and supports the eXtreme Low-Power (XLP) SLEEP mode for battery-aware designs. According to Microchip product documentation, the PIC16F15244 family adds Core Independent Peripherals (CIPs) and Intelligent Analog blocks that offload tasks from the CPU. Architecturally, the part uses a Harvard RISC architecture with separate program and data buses, plus the enhanced mid-range instruction set, which gives deterministic interrupt latency for real-time loops. The wide SOIC-20 (SO) footprint and PPS-based I/O remapping simplify PCB layout reuse across the PIC16F152xx family; Microchip's migration guide notes that PIC16F15244 devices serve as direct drop-in replacements for legacy PIC12F parts in SOIC packages. Typical applications include IoT sensor nodes, industrial automation modules, consumer appliance control boards, battery-powered measurement instruments, and compact motor/lighting controllers. For designs migrating from older PIC12F or PIC16F1xxx parts, the SOIC-20 footprint and PPS simplify schematic carry-over. When designing with this MCU, plan for decoupling capacitors on VDD/AVDD, follow Microchip's recommended decoupling guidance, and verify that your chosen compiler (XC8) version supports the PIC16F15244 device header. Production programmers such as MPLAB SNAP, PICkit 4, or MPLAB ICD 4 are compatible for in-circuit debug. This page synthesizes distributor stock signals, parametric drop-in alternatives, application guidance, and design notes drawn from Microchip's PIC16F15244 family documentation and community validation resources.

見積もりお問い合わせ

PIC16F15244-I/P

PIC16F15244-I/P - 8-Bit 32MHz 7KB Flash MCU | Microchip

The Microchip Technology PIC16F15244-I/P is an 8-bit PIC microcontroller from the PIC16F152xx family, featuring a 32 MHz enhanced mid-range core, 7 KB (4K x 14) of self-read/write Flash program memory, 512 bytes of RAM, and a 10-bit ADC, packaged in a 20-pin PDIP (P) through-hole format for industrial temperature applications. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory, data RAM, and integrated peripherals such as ADCs, timers, and communication modules. The PIC16F152xx family positions itself in the hierarchy as an 8-bit MCU -> mid-range MCU -> enhanced mid-range core MCU -> embedded controller, designed for cost-sensitive sensor and real-time control applications. The 8-bit architecture remains optimal for low-power, deterministic control tasks where 16/32-bit parts would be over-spec. Key features include Core Independent Peripherals (CIPs) such as two PWM modules and two CCP (Capture/Compare/PWM) channels, a 10-bit Analog-to-Digital Converter (ADC), Intelligent Analog with computation, Peripheral Pin Select (PPS) for flexible I/O routing, and standard communication peripherals including EUSART (Enhanced UART) and MSSP supporting both SPI and I2C. eXtreme Low Power (XLP) technology enables sleep currents in the nanoampere range with multiple wake sources. The PIC16F15244 uses the enhanced mid-range core with 49 instructions, 16 stack levels, and a hardware multiplier. The instruction set is orthogonal, simplifying code generation, while the Flash program memory supports self-read/write for in-application firmware updates. PPS allows most digital peripherals to be remapped to multiple I/O pins, simplifying PCB layout and enabling flexible system design. Typical applications include IoT sensor nodes, real-time control loops, consumer appliances, low-cost motor control, and battery-powered devices where sleep current dominates average consumption. Functional Safety (FuSa) capability suits industrial sensor monitoring, building automation, and appliance controllers requiring IEC 61508-compatible documentation. When designing with this MCU, reserve adequate Flash/RAM headroom for future firmware updates, use PPS to assign peripherals after final PCB layout, and pair the device with an external 32 kHz crystal or internal oscillator when low-power sleep accuracy is required. The 20-pin PDIP package supports easy prototyping and through-hole assembly for low-noise analog applications. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes not found in the manufacturer datasheet alone.

見積もりお問い合わせ

PIC16F15244-I/REB

PIC16F15244-I/REB - 8-bit MCU, 7KB Flash, 32MHz, 20-VQFN | Microchip

The Microchip Technology PIC16F15244-I/REB is an 8-bit PIC microcontroller from the PIC16F152xx family, delivering 32MHz CPU performance with 7KB (4K x 14 words) of Flash program memory in a compact 20-pin VQFN (3x3mm) package. This device is engineered for cost-sensitive sensor and real-time control applications and is part of Microchip's Functional Safety (FuSa) capable portfolio. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile data memory (RAM), and a configurable set of peripheral modules on one die. The PIC16F152 family belongs to Microchip's enhanced mid-range 8-bit core architecture, which falls under the broader category of embedded microcontrollers and semiconductor ICs. Designers choose 8-bit MCUs like the PIC16F15244 when deterministic response, ultra-low sleep current, and a small footprint outweigh the need for 32-bit computational throughput. Key features include 7KB Flash program memory, 512B RAM, a 10-bit ADC, two PWM modules, two CCP (Capture/Compare/PWM) peripherals, a hardware limiter (HLT), a windowed watchdog timer (WDT), Peripheral Pin Select (PPS) for flexible signal routing, one EUSART, SPI/I2C, and an eXtreme Low-Power (XLP) SLEEP mode. The PPS module allows digital peripherals to be reassigned to different I/O pins at runtime, simplifying PCB routing. The Functional Safety capability assists designers targeting IEC 61508 SIL-2 systems. The PIC16F15244 uses the enhanced mid-range 8-bit Harvard core with a 14-bit instruction word, providing deterministic interrupt latency and single-cycle hardware multiply (via the HLT). Core Independent Peripherals (CIPs) such as the CCP and PWM can operate without CPU intervention, reducing firmware complexity and power consumption. The device operates from 1.8V to 5.5V across an industrial -40C to +85C temperature range. Typical applications include consumer IoT sensor nodes, battery-powered home automation, low-cost motor control (small DC fans, BLDC pumps), LED lighting controllers, capacitive-touch user interfaces, and remote controls. Its tiny 3x3mm VQFN footprint enables placement in space-constrained wearable and handheld designs. A key design consideration is that the 3x3mm VQFN package has limited thermal dissipation; sustained high-current GPIO toggling will require PCB copper-pour thermal relief. Designers should also verify the PPS mapping for each peripheral before layout finalization. This page synthesizes distributor pricing, same-package drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

見積もりお問い合わせ

PIC16F15244-I/SS

PIC16F15244-I/SS - 8-bit MCU, 32MHz, 7KB Flash, 20-Pin | Microchip

The Microchip Technology PIC16F15244-I/SS is an 8-bit enhanced mid-range microcontroller built around a 32MHz internal core, integrating 7KB of self-read/write Flash program memory, 512 bytes of SRAM, and 256 bytes of EEPROM in a 20-pin SSOP (SS) package. Functional Safety (FuSa) ready hardware features, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology combine to deliver a robust yet efficient platform for cost-sensitive sensor and real-time control applications. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and peripheral interfaces on one die. PIC microcontrollers sit within the broader category of microcontrollers -> embedded microprocessors -> digital ICs -> integrated circuits, where 8-bit MCUs remain dominant in cost-optimized, deterministic control loops where power efficiency, interrupt latency, and small pin counts matter more than raw compute throughput. The PIC16F152xx family specifically targets applications requiring more on-chip intelligence than a basic GPIO expander while staying inside the 8-bit cost envelope. Key features include Peripheral Pin Select (PPS) for flexible signal routing, a 10-bit ADC with computation, a 5-bit DAC, two comparators, an 8-bit timer (TMR0), 16-bit Timer1/3, an 8-bit TMR2 with periodic interrupt, a hardware Universal Asynchronous Receiver Transmitter (EUSART), and a Master Synchronous Serial Port supporting both SPI and I2C. The 20-pin SSOP package exposes 18 I/O pins after power and ground allocations. Core Independent Peripherals such as the Configurable Logic Cell (CLC) and Complementary Waveform Generator (CWG) enable complex timing, motor-control, and signal-conditioning tasks to run without CPU intervention. Typical applications span appliance control, LED lighting drivers, sensor signal conditioning, automotive body electronics, consumer white goods, industrial IoT edge nodes, and small form-factor human-machine interface boards. The combination of XLP sleep currents, fast wake-up, and on-chip CIPs allows battery-powered designs to operate for years on a single cell. When designing with this part, allocate 4 I/O for the In-Circuit Serial Programming (ICSP) interface (ICSPCLK/ICSPDAT plus VPP/MCLR) if you require field re-flash capability. Always decouple VDD with a 100nF ceramic placed within 5mm of the pin, and follow Microchip AN-383 "Microcontroller Board Design" PCB guidelines to keep ADC readings clean. This page synthesizes distributor pricing, drop-in SSOP-20 alternatives from the same PIC16F152xx family, and practical design notes - information gain that complements the manufacturer datasheet without replacing it.

見積もりお問い合わせ

PIC16F15244T-I/REB

PIC16F15244T-I/REB - 8-Bit MCU 7KB Flash 32MHz 20-VQFN | Microchip

The Microchip PIC16F15244T-I/REB is an 8-bit PIC microcontroller from the PIC16F152xx functional-safety (FuSa) family, delivering 32 MIPS performance from a 32 MHz internal oscillator and housed in a 20-pin VQFN (3x3 mm) package with exposed pad. The device integrates 7 KB of self-programmable Flash, 512 bytes of RAM, and 256 bytes of EEPROM, with operating voltage from 1.8V to 5.5V across the industrial -40C to +85C range. The /REB suffix indicates the tape-and-reel VQFN package with industrial temperature grade. A PIC16 microcontroller is an 8-bit Harvard-architecture RISC MCU widely used in cost-sensitive embedded control. The PIC16F152xx family extends this legacy by adding Functional Safety (FuSa) support, Core Independent Peripherals (CIPs) such as Configurable Logic Cells (CLC), and eXtreme Low-Power (XLP) sleep modes that drop quiescent current to the nanoampere range - features that place the PIC16F15244 within the broader hierarchy of microcontroller -> embedded controller -> semiconductor IC. Key features include a 10-bit Analog-to-Digital Converter (ADC) with up to 12 channels, two 10-bit PWMs, two Capture/Compare/PWM (CCP) modules, Peripheral Pin Select (PPS) for flexible I/O routing, and standard serial interfaces including EUSART, SPI, and I2C. The on-chip high-performance 32 MHz oscillator eliminates an external crystal in many designs, while the Windowed Watchdog Timer (WWDT) and Hardware Limit Timer (HLT) support safety-critical firmware. The architecture pairs a RISC core with intelligent analog (10-bit ADC, internal voltage reference) and digital (CLC, NCO, PWM) peripherals, allowing sensor interfacing, motor control loops, and safety handshakes to run without CPU intervention. Functional-safety collateral such as FMEDA and diagnostic libraries targets IEC 61508 SIL-2 capable designs when the datasheet-recommended firmware patterns are followed. Typical applications include industrial sensor nodes, building-automation controllers, low-power IoT end-points, LED lighting control, consumer appliances, and functional-safety subsystems such as appliance motor monitoring or smoke/CO detector signal chains. The compact 3x3 mm VQFN package suits space-constrained PCBAs. When designing with this device, select MPLAB X IDE with XC8 compiler and configure PPS registers to remap peripheral functions to physical pins. Always route the exposed thermal pad to a continuous ground plane for thermal dissipation and EMI performance, and place 100 nF decoupling capacitors within 3 mm of each VDD pin per Microchip's recommended layout. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, accelerating your part-selection and PCB layout decisions for PIC16F15244-based designs.

見積もりお問い合わせ

PIC16F15244T-I/SO

PIC16F15244T-I/SO - 8-Bit 32MHz 7KB Flash MCU | Microchip

The Microchip Technology PIC16F15244T-I/SO is an 8-bit PIC microcontroller with 32 MHz CPU speed, 7 KB (4K x 14) Flash program memory, and Functional Safety (FuSa) support, housed in a 20-pin SOIC package. Operating from 1.8V to 5.5V, it provides 512 bytes of RAM, 256 bytes of EEPROM, and a 10-bit ADC. An 8-bit microcontroller (MCU) is a small, low-cost, single-chip computer that integrates a CPU, program memory (Flash), data RAM, and peripherals such as ADC, timers, and communication interfaces. MCUs sit in the embedded-system hierarchy above sensors and below system-on-modules, executing firmware that reads inputs, processes logic, and drives outputs. The PIC16F152xx family specifically targets cost-sensitive sensor and real-time control applications with a streamlined CIP (Core Independent Peripheral) set and eXtreme Low-Power (XLP) Sleep modes for battery-powered designs. Key features of the PIC16F15244T-I/SO include a 32 MHz internal oscillator, 10-bit ADC with up to 12 channels, two PWM modules, two CCP (Capture/Compare/PWM) modules, hardware Limit Timer (HLT), Watchdog Timer (WDT), Peripheral Pin Select (PPS), EUSART, and SPI/I2C interfaces. The XLP Sleep Mode reduces quiescent current for battery applications, and Memory Access Partition (MAP) supports bootloader and FuSa-grade isolation between non-secure and secure firmware regions. The device uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word, providing deterministic interrupt latency and a single-cycle instruction execution at 32 MHz. PPS allows digital peripheral pin reassignment, which simplifies PCB layout and reduces design rework. Functional Safety features make the part suitable for safety-critical appliance, industrial sensor, and home-automation designs targeting IEC 60730 Class B. Typical applications include consumer appliance control, IoT sensor nodes, battery-powered instrumentation, LED lighting controllers, and small motor/valve control loops. The wide 1.8V-5.5V operating range and integrated analog make the part drop-in friendly for portable, mains-bucked, and rechargeable-battery designs. When designing with this device, place decoupling capacitors within 2 mm of VDD/AVDD pins, avoid driving ADC inputs with high-impedance sources without a buffer, and verify unused I/O pin configuration (input or output, never floating) to minimize Sleep-mode current draw. Use PPS only on digital peripherals to maintain ADC reference integrity. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including comparison data against same-family and cross-brand 20-pin 8-bit MCU alternatives.

見積もりお問い合わせ

PIC16F15245-E/SO

PIC16F15245-E/SO - 32MHz 8-bit MCU 14KB Flash SOIC-20 | Microchip

The Microchip Technology PIC16F15245-E/SO is an 8-bit RISC microcontroller from the PIC16F152xx family, featuring a 32MHz enhanced mid-range core, 14KB (8K x 14) of self-read/write Flash program memory, 1KB SRAM, and 256 bytes of EEPROM, all housed in a 20-pin SOIC package. It integrates a 10-bit Analog-to-Digital Converter (ADC), two Capture/Compare/PWM (CCP) modules, two PWM channels, an EUSART, MSSP (SPI/I2C), Peripheral Pin Select (PPS), Hardware Limit Timer (HLT), Watchdog Timer (WDT), and eXtreme Low-Power (XLP) sleep mode, while delivering up to 18 general-purpose I/O lines. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path that executes one byte per instruction cycle; PIC MCUs sit in the broader taxonomy of microcontroller -> embedded computing device -> semiconductor IC. The PIC16F15245 belongs to Microchip's enhanced mid-range PIC16 family, which uses a 14-bit instruction word and a 16-level hardware stack, offering a balance of deterministic real-time control, low power consumption, and Core Independent Peripherals (CIPs) that offload tasks from the CPU. This class of MCU is widely used in cost-sensitive sensor and real-time control designs where deterministic response and low quiescent current matter more than raw compute throughput. Key features of the PIC16F15245-E/SO include its 32MHz internal oscillator (8MHz with 4x PLL), 14KB Flash, 1KB RAM, 10-bit ADC with internal voltage reference and computation modes, two CCP and two PWM peripherals, and Microchip's eXtreme Low-Power XLP sleep mode with nanoWatt XLP technology. The Peripheral Pin Select (PPS) block allows flexible remapping of digital peripherals to any I/O pin, which simplifies PCB routing and supports multiple communication stacks on a fixed pinout. On-chip Core Independent Peripherals such as the Hardware Limit Timer (HLT) and Configurable Logic Cell (CLC) let state machines and timing-critical loops run without CPU intervention. Typical applications include sensor node conditioning and IoT edge devices, low-power battery-powered consumer products, home automation controllers, white-goods user-interface boards, LED lighting drivers with PWM dimming, and cost-sensitive industrial control logic. The combination of 14KB Flash, 1KB RAM, PPS, and the 10-bit ADC with computation (ADC2) also makes this device well suited to PID-style closed-loop control, multi-channel sensor readout, and simple user-interface HMI designs that need reliable real-time response. When designing with this part, note that the 'E' suffix designates the extended (-40C to +125C) operating temperature range and 'SO' is the 20-pin SOIC (300-mil) package. PPS remapping must be configured before enabling peripheral output, and the ADC's computation modes benefit from a dedicated 1.2V band-gap reference for ratiometric measurements. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

見積もりお問い合わせ

PIC16F15245-I/P

PIC16F15245-I/P - 8-Bit MCU, 14KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F15245-I/P is an 8-bit PIC microcontroller based on the enhanced mid-range PIC16 CPU core, delivering up to 32 MHz of operation with 14 KB of Flash program memory and 1024 bytes of SRAM, housed in a 20-pin PDIP (P) through-hole package. The device integrates a 10-bit ADC, two PWM modules, two CCP capture/compare/PWM peripherals, a hardware limiter (HLT), watchdog timer, Peripheral Pin Select (PPS), EUSART, SPI, and I2C, all while supporting eXtreme Low-Power (XLP) Sleep mode for battery-driven designs. An 8-bit microcontroller (MCU) is a single-chip computer with an 8-bit data path, optimized for cost-sensitive embedded control. Within the broader taxonomy, the PIC16F15245 sits as: 8-bit MCU -> PIC16 family -> enhanced mid-range core -> PIC16F152xx sub-family -> 20-pin general-purpose Flash MCU. It belongs to the wider category of microcontrollers -> microprocessors -> semiconductors -> integrated circuits. The 20-pin PDIP package provides easy prototyping and breadboard compatibility, making this variant particularly attractive for development, education, and low-volume production. Key differentiating features include the Peripheral Pin Select (PPS) which allows user-defined remapping of digital peripherals to I/O pins, the 10-bit ADC with internal voltage reference for sensor interfacing, and Core Independent Peripherals (CIPs) that operate without CPU intervention. The XLP Sleep mode enables nanoWatt-class standby current, making the part suited for battery-powered IoT end nodes. The hardware limiter (HLT) provides hardware-based signal conditioning without software overhead. The PIC16F15245 implements Microchip's enhanced mid-range 16-bit instruction set architecture with a hardware multiplier, providing deterministic interrupt latency and 35 instructions for compact code generation. Its internal 32 MHz oscillator eliminates the need for an external crystal in many applications, while optional clock modes support lower frequencies for power-sensitive designs. Typical applications include industrial sensor nodes, consumer appliance controls, battery-powered IoT devices, LED lighting controllers, low-cost motor control loops, and educational development platforms. The combination of CIPs and PPS enables designers to reduce BOM cost by eliminating external logic ICs. When designing with the PIC16F15245-I/P, ensure that unused I/O pins are configured as outputs or tied to defined logic levels to minimize supply current. The PPS feature requires careful pin assignment review during code development; MPLAB X IDE with MCC provides graphical configuration to streamline this process. This page synthesizes distributor pricing, drop-in alternatives from the same PIC16F152xx family, and practical design notes not found in the standalone manufacturer datasheet.

見積もりお問い合わせ

PIC16F15245-I/REB

PIC16F15245-I/REB - 8-Bit MCU, 14KB Flash, 20-VQFN | Microchip

The Microchip PIC16F15245-I/REB is an 8-bit PIC16 microcontroller from the PIC16F152xx family featuring 14KB (8K x 14) of self-read/write Flash program memory, 1KB of RAM, and a 32 MHz internal oscillator core. Housed in a compact 20-pin VQFN (3x3 mm) package, this device targets cost-sensitive sensor and real-time control applications. The 32 MHz CPU delivers up to 8 MIPS instruction throughput using Microchip's 49-instruction enhanced mid-range core with 16 stack levels. A microcontroller (MCU) is a single-chip computer containing a CPU, program memory (Flash/ROM), data memory (RAM), and integrated peripherals such as timers, ADC, communication interfaces, and I/O pins. Within the broader taxonomy, an 8-bit MCU sits between fixed-function logic ICs and 32-bit application processors, occupying the cost-sensitive sweet spot for embedded designs. The PIC16F15245 belongs to the PIC16F mid-range MCU family, sitting between the PIC10/12/14 baseline families and the PIC18/dsPIC enhanced families. Microcontrollers enable Core Independent Peripherals (CIPs) that operate without CPU intervention, freeing the core for application logic. Key differentiating features include Core Independent Peripherals (CIPs), Intelligent Analog with a 10-bit ADC, two PWM modules, two CCP (Capture/Compare/PWM) channels, Peripheral Pin Select (PPS) for flexible pin mapping, and an EUSART plus MSSP supporting SPI and I2C communication. The XLP (eXtreme Low-Power) SLEEP mode enables battery-friendly operation down to nanoamp currents. The 20-VQFN (3x3) package achieves a footprint under 9 mm², ideal for space-constrained PCB layouts where SOIC-20 would be too large. The architecture combines the 14-bit instruction word enhanced mid-range core with hardware multiplier, deterministic interrupt latency, and dual-operation Flash with self read/write capability for in-application firmware updates. Internal voltage reference support and a configurable oscillator block reduce external component count. Typical applications include IoT sensor nodes, low-power battery-powered instrumentation, home appliance control, LED lighting controllers, automotive body electronics sub-modules, and industrial sensor interfaces. The combination of PPS, eXtreme Low-Power modes, and the small VQFN footprint makes the part especially well-suited for wearable and remote-sensor designs. When designing with this device, allocate adequate Flash for bootloaders if OTA updates are planned - the 14KB Flash includes self-read/write but boot block size should be confirmed against the latest datasheet revision. PPS configuration must be locked before peripheral use; an unlocked PPS module returns peripherals to default pins. This page synthesizes Microchip distributor pricing, drop-in same-package alternatives drawn from the same PIC16F152xx family, and practical design notes not collated in the standalone datasheet, providing engineers a single comparison surface for sourcing decisions.

見積もりお問い合わせ

サブカテゴリ

製品 (38,000+)

PIC16F15224-I/P - 8-bit MCU 7KB Flash 32MHz 14-PDIP | Microchip

PIC16F15224-I/ST - 8-bit MCU 7KB Flash 32MHz TSSOP-14 | Microchip

PIC16F15225-E/SL - 14KB Flash 8-bit MCU, 32MHz | Microchip

PIC16F15225-I/MG - 8-bit MCU, 14KB Flash, 32MHz, 16-QFN | Microchip

PIC16F15225-I/SL - 14KB Flash 8-bit MCU 32MHz | Microchip

PIC16F15225-I/ST - 14KB Flash 8-bit MCU, 32MHz, TSSOP-14 | Microchip

PIC16F15225T-I/ST - 8-Bit MCU, 14KB Flash, 32MHz, 14-TSSOP | Microchip

PIC16F15243-E/P - 8-bit 32MHz 3.5KB Flash MCU | Microchip

PIC16F15243-E/REB - 8-bit 32MHz 3.5KB Flash MCU | Microchip

PIC16F15243-E/SO - 8-bit MCU, 3.5KB Flash, 20-Pin SOIC | Microchip

PIC16F15243-E/SS - 8-bit 32MHz 3.5KB Flash MCU 20-SSOP | Microchip

PIC16F15243-I/REB - 8-bit 32MHz MCU, 3.5KB Flash, 20-VQFN | Microchip

PIC16F15243-I/SS - 8-bit MCU, 3.5KB Flash, 20-SSOP | Microchip

PIC16F15243T-I/REB - 8-bit MCU, 3.5KB Flash, 32MHz, 20-VQFN | Microchip

PIC16F15243T-I/SO - 8-bit MCU, 3.5KB Flash, 20-SOIC | Microchip

PIC16F15244-E/SO - 8-bit PIC16 MCU, 7KB Flash, SOIC-20 | Microchip

PIC16F15244-I/P - 8-Bit 32MHz 7KB Flash MCU | Microchip

PIC16F15244-I/REB - 8-bit MCU, 7KB Flash, 32MHz, 20-VQFN | Microchip

PIC16F15244-I/SS - 8-bit MCU, 32MHz, 7KB Flash, 20-Pin | Microchip

PIC16F15244T-I/REB - 8-Bit MCU 7KB Flash 32MHz 20-VQFN | Microchip

PIC16F15244T-I/SO - 8-Bit 32MHz 7KB Flash MCU | Microchip

PIC16F15245-E/SO - 32MHz 8-bit MCU 14KB Flash SOIC-20 | Microchip

PIC16F15245-I/P - 8-Bit MCU, 14KB Flash, 32MHz | Microchip

PIC16F15245-I/REB - 8-Bit MCU, 14KB Flash, 20-VQFN | Microchip