集積回路

サブカテゴリ

📁 ADC/DAC 2518 製品 📁 アンプIC 793 製品 📁 オーディオコーデック 16 製品 📁 オーディオIC 2 製品 📁 クロック＆タイミング 287 製品 📁 DSP 962 製品 📁 データ収集IC 2 製品 📁 デジタルポテンショメータ 4 製品 📁 ディスプレイドライバ＆コントローラ 1 製品 📁 FPGA & CPLD 6666 製品 📁 インターフェースIC 1568 製品 📁 LEDドライバ 1 製品 📁 ロジックIC 305 製品 📁 メモリIC 875 製品 📁 マイクロコントローラ 18688 製品 📁 マイクロプロセッサ 4 製品 📁 モータドライバ 1 製品 📁 その他 1 製品 📁 Sensor and Detector Interfaces 1 製品 📁 専用IC 15 製品 📁 ビデオIC 13 製品

製品 (32725)

PK30N512VMD100 - 100MHz Cortex-M4 512KB MCU | NXP
PK30N512VMD100

PK30N512VMD100 - 100MHz Cortex-M4 512KB MCU | NXP

NXP Semiconductors PK30N512VMD100 is a 32-bit ARM Cortex-M4 Kinetis K30 microcontroller operating up to 100 MHz, with 512 KB of programmable Flash and 128 KB of RAM, in a 144-MAPBGA package measuring 13 x 13 mm. The device provides 102 I/O connections and integrates CANbus, EBI/EMI, I2C, IrDA, SD, SPI, UART/USART, DMA, I2S, LCD, LVD, POR, PWM, and watchdog functions. A microcontroller is a programmable system-on-chip that combines a processor core, nonvolatile program memory, volatile data memory, and peripheral interfaces on one semiconductor device. The PK30N512VMD100 belongs to the Kinetis K30 family and sits within the hierarchy of ARM Cortex-M4 embedded processor, 32-bit microcontroller, embedded systems controller, and semiconductor. Its combination of memory and communication peripherals supports compact control systems that must handle both control logic and external serial devices. Verified device features include a 100 MHz clock, 512 KB Flash organized as 512K x 8, 128K x 8 RAM, and 102 I/O pins. Listed connectivity includes CANbus, EBI/EMI, I2C, IrDA, SD, SPI, and UART/USART. Listed peripherals include DMA, I2S, an LCD controller, low-voltage detection, power-on reset, PWM, and a watchdog timer. These interfaces make the MCU applicable to industrial control, communications, display-oriented embedded equipment, audio data handling, and motor or power-control systems. The part is identified in the supplied source material as obsolete, and one distributor listing describes it as a pre-qualification sample. Its K30 architecture therefore requires lifecycle attention during design selection: existing supported designs should confirm sourcing and qualification, while new designs should avoid committing to an obsolete MCU unless long-term availability is independently secured. The 144-MAPBGA package also demands BGA assembly capability, careful escape-routing planning, and adequate thermal design. Typical implementation places the MCU between sensors, communication transceivers, display peripherals, actuators, and external memory. Firmware must configure clocks and peripherals, while the board must provide regulated supply rails, decoupling, reset handling, clock stability, and programming/debug access. The supplied sources do not provide a complete verified pinout, electrical limits, or a full set of operating ranges. For a new board, do not infer pin compatibility from the 144-BGA package name alone. Compare every ball assignment, power domain, peripheral mapping, voltage limit, and software device configuration against the manufacturer documentation. The listed alternative comparison results identify functionally related devices but do not establish true pin-to-pin drop-in replacements. This page consolidates distributor specifications, lifecycle indications, interface details, package information, and engineering cautions into a design-oriented reference for the PK30N512VMD100. It is intended to support sourcing, legacy maintenance, and feasibility review without inventing electrical values absent from the verified data.

見積もり 在庫あり
PK30X256VLQ100 - 100MHz Cortex-M4 MCU 256KB Flash | NXP Kinetis
PK30X256VLQ100

PK30X256VLQ100 - 100MHz Cortex-M4 MCU 256KB Flash | NXP Kinetis

The NXP (formerly Freescale) PK30X256VLQ100 is an ARM Cortex-M4 Kinetis K30 family 32-bit microcontroller running at 100 MHz with 256 KB of embedded Flash program memory, packaged in a 144-pin LQFP (20 mm x 20 mm). According to the NXP Kinetis K30 datasheet, the device integrates 256 KB of Flash, 64 KB of SRAM, an LCD segment driver controller, USB 2.0 Full-Speed with on-chip PHY, CAN, I2C, SPI, UART, ADC, and 102 general-purpose I/O pins suitable for human-machine interface and industrial control panels. What is an ARM Cortex-M4 microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (RAM), and peripherals such as timers, communication interfaces, and analog blocks. The ARM Cortex-M4 core is a 32-bit processor implementing the Thumb-2 instruction set, with hardware single-precision floating-point and DSP extensions. The Cortex-M4 architecture sits in the taxonomy: microcontroller -> embedded MCU -> ARM Cortex-M family -> Cortex-M4 core -> semiconductor. The Kinetis K30 sub-family is optimized for low-power, segment-LCD display applications. Key features include a Cortex-M4 core with FPU and DSP instructions, 256 KB Flash, 64 KB SRAM, an integrated segment LCD controller (up to 8x40 segments per the K30 family specification), USB 2.0 Full-Speed with on-chip transceiver, CAN 2.0B interface, multiple low-power modes, and an internal oscillator. The 144-LQFP package exposes the full set of K30 peripheral pins including the external bus interface for expanded memory or graphics. The PK30X256VLQ100 is qualified to AEC-Q100 Grade 1 automotive standards and operates across the industrial temperature range, supporting voltage rails from 1.71 V to 3.6 V. The wide voltage range allows direct connection to single-cell Li-ion (3.0-3.6 V) or regulated 1.8 V/3.3 V system rails without level translation, simplifying BOM. Typical applications include automotive instrument clusters with segment-LCD, industrial HMI panels, smart metering (electricity/gas/water), medical infusion pumps with LCD readout, point-of-sale terminals, and home appliance control boards. The on-chip LCD driver eliminates the need for an external LCD bias generator, reducing BOM cost in display-equipped products. When designing with this device, ensure adequate decoupling (100 nF + 4.7 uF per VDD pair) and follow NXP's recommended SDcard/USB layout guidelines for the USB Full-Speed data lines to meet radiated-emission compliance. Pre-qualification samples are shipped under the "PK30" prefix; production parts use the "MK30" prefix. This page synthesizes distributor stock, drop-in NXP K30 family alternatives, and practical layout notes not duplicated in the manufacturer datasheet.

USD $9.75 在庫あり
PK40N512VMD100 - 32-bit 100 MHz MCU with 512 KB Flash | NXP
PK40N512VMD100

PK40N512VMD100 - 32-bit 100 MHz MCU with 512 KB Flash | NXP

The NXP Semiconductors PK40N512VMD100 is a 32-bit ARM Cortex-M4 Kinetis K40 microcontroller rated up to 100 MHz, with 512 KB of Flash memory, 128 KB of RAM, and 98 I/O pins in a 144-pin MAPBGA package measuring 13 mm by 13 mm. Its operating voltage is reported as 1.8 V, 2.5 V, or 3.3 V, while one source specifies a 1.71 V to 3.6 V operating range. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The PK40N512VMD100 belongs to the ARM Cortex-M4 microcontroller class, within the broader embedded-processor and semiconductor hierarchy. It is intended for embedded control systems that require deterministic real-time execution, substantial local program storage, and multiple peripheral connections. The device provides 512 KB of Flash organized as 512K by 8 bits and 128K by 8 bits of RAM. Its ARM Cortex-M4 processor operates at up to 100 MHz, allowing software to execute control logic, communications, data acquisition, and user-interface tasks in one integrated device. The 98 available I/O positions support external sensors, actuators, communications interfaces, display connections, and other system resources. The PK40N512VMD100 is identified as a Kinetis K40 MCU with USB and LCD capability in distributor listings. It also offers multiple voltage options and an internal oscillator. Because this is a complex 144-ball device, designers should validate the exact pin functions, electrical limits, memory features, and peripheral availability against the official NXP or Freescale documentation before committing a PCB layout. Typical applications include industrial automation, embedded control, medical-device monitoring, automotive electronics, USB-connected equipment, and systems requiring a low-power microcontroller with local Flash storage. Its 100 MHz Cortex-M4 core and 512 KB Flash provide a useful balance of processing capacity and memory for moderately complex embedded products. The most important design consideration is package and pinout validation. The 144-MAPBGA footprint requires a multilayer PCB with fine-pitch escape routing and careful ball assignment; a wrong footprint cannot be corrected by simple rework. Confirm the exact ordering code, voltage option, temperature grade, and exposed-ball requirements against the manufacturer datasheet before production release. This page combines distributor specifications, sourcing information, and practical selection guidance for the PK40N512VMD100. It does not invent pin assignments, current ratings, or operating limits that were not present in the verified source material.

見積もり 在庫あり
PK64FN1M0VLQ12 - 120MHz Cortex-M4 MCU, 1MB Flash | NXP
PK64FN1M0VLQ12

PK64FN1M0VLQ12 - 120MHz Cortex-M4 MCU, 1MB Flash | NXP

The NXP PK64FN1M0VLQ12 is a 120 MHz ARM Cortex-M4 microcontroller with FPU, 1 MB of Flash and 256 KB of SRAM, supplied in a 144-pin LQFP (20x20 mm) package. According to NXP, this device sits inside the Kinetis K64 sub-family and provides IEEE 1588 Ethernet, USB with on-chip HS PHY, security modules, and a rich peripheral set for industrial connectivity. Pricing as of 2026-10-09: $9.24 at qty 1, dropping to $7.45 at 100 pieces and $6.62 at 1000. What is a Kinetis K-series MCU? A Kinetis MCU is a 32-bit ARM Cortex-M microcontroller family from NXP designed for connected, mixed-signal embedded applications. The PK64 sits in the K64 sub-family, which scales the Cortex-M4 core with FPU up to 120 MHz and adds Ethernet, USB, and crypto/security peripherals. In the broader taxonomy it belongs to: MCU -> ARM Cortex-M4 -> Kinetis K-series -> connected/industrial MCU category. Key features of the PK64FN1M0VLQ12 include an ARM Cortex-M4 core with single-precision FPU, 120 MHz CPU clock, 1 MB program Flash, 256 KB SRAM, full-speed and high-speed USB 2.0 On-The-Go with on-chip HS PHY, 10/100 Ethernet MAC with IEEE 1588 support, hardware encryption (AES, DES, SHA) and tamper detection, 12-bit ADC and DAC, FlexTimers, low-power run/wait/standby modes, and a wide operating voltage range from 1.71 V to 3.6 V. The 144-pin LQFP provides ample I/O for industrial bus and motor-control applications. From an architectural standpoint, the PK64 integrates a bus matrix that allows simultaneous DMA-driven access to SRAM, Ethernet and USB peripherals without CPU stalls. The Cortex-M4 FPU accelerates DSP and floating-point control loops, which is critical for power conversion and motor control. The integrated high-speed USB PHY and Ethernet MAC reduce BOM cost and PCB area versus discrete implementations. Hardware crypto blocks offload AES/SHA from software, leaving the core free for application logic. Typical applications include industrial Ethernet gateways, PLC and fieldbus nodes, factory automation controllers, motor drives and inverters, building automation (BACnet/Modbus), and POS or networked print devices. The 144-pin LQFP footprint supports designs that need many I/O lines for parallel buses, multi-axis motor control, or color displays. For engineers choosing between the PK and MK prefixes of the same silicon, the PK prefix denotes a pre-production part while MK denotes production volume; both share the same K64 die. A key design consideration is to plan clock and supply decoupling for the dual-mode USB PHY, place the 50-ohm Ethernet differential pair with controlled impedance, and ensure firmware is configured for either 25 MHz or 50 MHz external crystal modes supported by the K64. Flash security and tamper pins should be bonded correctly if the cryptographic accelerator is used. This page synthesizes NXP distributor pricing, K64 family drop-in alternatives, application reference designs, and PCB design notes not present in a single datasheet view.

USD $6.62 在庫あり
PKE18F512VLL16 - Kinetis KE18F 168MHz Cortex-M4F MCU | NXP
PKE18F512VLL16

PKE18F512VLL16 - Kinetis KE18F 168MHz Cortex-M4F MCU | NXP

The NXP PKE18F512VLL16 is a Kinetis KE18F series 32-bit Arm Cortex-M4F microcontroller running up to 168 MHz, packaged in a 100-pin LQFP (14x14 mm). It integrates 512 KB of Flash, 64 KB of FlexMem, and 64 KB of SRAM, providing high-density on-chip memory for 5V-tolerant industrial and automotive body applications. The part is built on a robust 5V process that supports 2.7V to 5.5V supply operation, with dual CAN 2.0B FlexCAN interfaces and a rich mix of analog and digital peripherals. A Kinetis KE1xF MCU is the high-end tier of the broader Kinetis E family, where Kinetis E (industrial/automotive 5V Cortex-M0+) -> Kinetis KE1xF (Cortex-M4F 5V high-performance) -> Cortex-M4F (Arm core) -> ARM Cortex-M family (32-bit microcontrollers) -> MCU (Microcontroller Unit) -> Embedded System. The KE18F is engineered for harsh 5V environments (industrial control, HVAC, smart metering, white goods, automotive body) where 3.3V-native MCUs fail due to EMC or transient immunity. Compared to legacy 8-bit 8051 / 16-bit HC(S)08 / 32-bit ColdFire designs, the KE18F delivers an order-of-magnitude performance jump while keeping the same 5V I/O tolerance. Key features include a single-precision FPU, DSP instructions, 32 KB FlexNVM with EEPROM capability, DMA, ADC (12-bit, fast conversion), FlexTimers, periodic interrupt timers, a real-time clock, and on-chip EEPROM emulation. Two CAN 2.0B channels, multiple UARTs, SPIs, I2Cs, and an integrated 5V regulator simplify multi-rail designs. Typical applications include industrial motor control (BLDC/PMSM FOC), HVAC control boards, smart electricity meters, white goods, body control modules, and battery management systems for low-voltage storage. The 100-LQFP footprint allows 4-layer FR4 layout with no exotic stackup. When designing with KE18F, plan a 100-LQFP layout with adequate thermal relief and route the VBAT pin directly to the backup battery. Use the FlexMemory partition command to allocate FlexNVM as EEPROM before final code lock. This page synthesizes distributor pricing, drop-in NXP same-family alternatives, and practical layout notes not collated in the official NXP datasheet.

USD $7.18 在庫あり
PL2303GC - USB to UART Bridge Controller, SSOP-28 | Prolific
PL2303GC

PL2303GC - USB to UART Bridge Controller, SSOP-28 | Prolific

The Prolific PL2303GC is a low-cost, high-performance USB-to-Serial Bridge Controller that provides a convenient small-footprint solution for connecting an RS232-like full-duplex asynchronous serial device to any USB host. Housed in a 28-pin SSOP package, the device integrates a USB 2.0 Full-Speed transceiver, a full UART engine, GPIO pins, and battery-charging detection logic compliant with USB BC1.2. It supports data rates up to 12 Mbps over USB and offers a wide range of baud-rate settings on the UART side, making it suitable for industrial connectivity, embedded debug consoles, point-of-sale terminals, and legacy RS232 migration. A USB-to-UART bridge controller is a category of interface IC that converts USB signaling on the host side into traditional asynchronous serial (UART) signaling on the device side. The hierarchy is USB-to-Serial bridge -> UART controller -> asynchronous serial interface -> Interface IC -> Integrated Circuit. These bridges allow designers to add USB connectivity to existing UART-based microcontrollers, sensors, and modules without rewriting firmware, by emulating a legacy COM port through a virtual-COM-port driver on the host. Key features of the PL2303GC include integrated USB 2.0 Full-Speed (12 Mbps) PHY, a configurable UART supporting 5/6/7/8 data bits and 1/1.5/2 stop bits, hardware and software flow control (XON/XOFF, RTS/CTS, DTR/DSR), multiple GPIO pins for status or control signaling, and support for USB Battery Charging Specification 1.2 (BC1.2). The device operates from a single 3.3 V supply, draws low suspend current, and integrates an internal clock multiplier so no external crystal is required, reducing BOM cost. Architecturally, the PL2303GC combines a USB Serial Interface Engine (SIE), a 48 MHz internal PLL, an asynchronous serial engine with 256-byte FIFOs in each direction, and the BC1.2 charger-detection state machine. The high FIFO depth prevents UART underrun at high baud rates and decouples the host polling interval from the device-side data rate. Typical applications include USB-to-RS232 debug cables for embedded development, industrial control boards replacing legacy COM ports, USB barcode scanners, GPS modules, point-of-sale terminals, and any system needing legacy serial connectivity from a modern USB-only host. The on-chip GPIO and BC1.2 detection also suit charging-cable applications where the upstream port must signal charging current to a downstream device. When designing with the PL2303GC, note that it is pin-to-pin compatible with the legacy PL2303HXD and PL2303TA in SSOP-28, but the external BOM differs - the new part requires fewer passives. Plan for the migration schematic referenced in the Prolific application note PL2303GC-SSOP28_Migration-Guide. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

USD $0.82 在庫あり
PL2303TA - USB to Serial Bridge Controller | SSOP-28 | Prolific
PL2303TA

PL2303TA - USB to Serial Bridge Controller | SSOP-28 | Prolific

The Prolific PL2303TA is a low-cost, high-performance USB-to-Serial Bridge Controller housed in a 28-pin SSOP (208 mil) package, providing a simple bridge between USB and UART interfaces. According to the Prolific PL2303TA datasheet, this IC integrates USB 2.0 full-speed PHY and a full UART engine, enabling legacy RS-232 peripherals to communicate over USB without external firmware on the host MCU. Pricing for the PL2303TA starts near $0.79 per unit at LCSC as of 2026-10-14. A USB-to-Serial Bridge Controller is a bridge IC that converts between a USB device port and an asynchronous serial (UART) channel. It belongs to the product hierarchy USB bridge IC -> interface controller -> IC -> semiconductor. The bridge typically enumerates as a virtual COM port (VCP) on the host operating system, so legacy serial-terminal software can communicate with the target MCU through the same APIs as a built-in COM port. The PL2303TA sits below the USB transceiver and above the target MCU's UART peripheral, making it a standard drop-in for cable, debug-console, and industrial-converter designs. Key features of the PL2303TA include USB 2.0 full-speed (12 Mbps) device interface, integrated 3.3V LDO for internal logic (the I/O rail still needs to be supplied externally), ROM-based default firmware (no external EEPROM required for basic VCP operation), support for baud rates from 75 bps up to 6 Mbps in the latest driver set, and full UART handshaking including RTS, CTS, DTR, DSR, RI, and DCD. The device operates from a single 5V USB bus input and exposes a logic-level UART toward the target MCU at 3.3V CMOS levels. Internally, the PL2303TA combines a serial-interface engine (SIE), a USB protocol controller, a FIFO buffer, and the UART block on a single die. The integrated voltage regulator supplies the internal core, while a separate VDD_232 pin powers the external RS-232 level shifter when a true RS-232 transceiver (e.g., SP3232E) is fitted. Compared with the legacy PL2303HXA and PL-2303XA parts, the TA version reduces BOM by removing the external EEPROM requirement and lowering quiescent current, and is pin-to-pin compatible with the PL-2303HXA/PL-2303XA footprint for PCB migration. Typical applications include USB-to-RS-232 converter cables, USB-to-TTL serial-debug console cables for Raspberry Pi / Arduino / ESP32 / Jetson boards, GPS module interfaces, industrial RS-232 modem replacement, and point-of-sale / barcode-scanner serial interfaces. The internal ROM code is loaded by driver on Windows 7/8/10 with the official Prolific PL2303 driver; macOS and Linux include native cdc-acm / pl2303 kernel modules. Designers should note: (1) Windows 11 has been known to default-block older PL2303 part revisions, so the PL2303TA is the recommended current revision; (2) for proper RS-232 level translation, pair the PL2303TA with an SP3232E or similar charge-pump transceiver; (3) decouple VDD_232 and VDD_IO with at least 0.1 uF ceramic capacitors placed as close as possible to the IC pins. The SSOP-28 (208 mil) package has a typical theta_JA around 90 C/W, which is comfortable for USB-powered, low-power designs. This page synthesizes distributor pricing, drop-in alternatives inside the SSOP-28 footprint, and practical design notes not found in the Prolific datasheet - giving you the cross-reference summary needed to design or replace the PL2303TA in next-generation USB-to-Serial products.

USD $0.34 在庫あり
PM583 - AC500 PLC Processor with 1 MB Memory | ABB
PM583

PM583 - AC500 PLC Processor with 1 MB Memory | ABB

The ABB PM583 is an AC500 programmable logic controller processor module with 1 MB of memory, Ethernet communication, two RS232/RS485 interfaces, an FBP interface, and a display. It is associated with ABB product ID 1SAP140300R0271 and is intended for industrial automation systems requiring local control, communications, and expansion-module integration. The supplied ABB product information identifies the module as PM583-ETH, while the requested MPN is PM583; confirm the exact ordering designation before purchasing. A PLC processor module is the central control element of an industrial automation system. It executes control logic, coordinates communication interfaces, and connects to local or distributed I/O. The PM583 belongs to the AC500 processor-module family and is associated with the PM57x, PM58x, and PM59x technical-data family rather than a discrete semiconductor package. Its communications and memory characteristics make it relevant to machine control, building automation, process monitoring, and equipment diagnostics where a controller must coordinate multiple field devices. The verified information specifies 1 MB of memory, Ethernet, two RS232/RS485 interfaces, FBP, and a display. The PM583 family documentation also identifies AC500 system data and describes processor-module capabilities, but the supplied snippets do not provide every detailed electrical, environmental, timing, or expansion specification. Those missing values are intentionally not inferred. ABB product pages and the manufacturer technical-data document should be consulted before final design release, particularly for supply voltage, processor performance, environmental limits, communication protocols, and local I/O limits. The listed ABB documentation refers to the PM57x, PM58x, and PM59x processor-module family and distinguishes standard AC500/S500 data from XC variants. This means the PM583 designation must be matched carefully to the exact product variant and system configuration. The PM583-ETH page is the strongest verified product-page match, while the PM583-ETH-XC page represents a distinct XC-related product and should not be treated as an automatic drop-in replacement. Typical industrial uses include AC500 machine-control projects, serial-device integration, Ethernet-connected production equipment, and supervisory factory automation. The display and communication interfaces can support diagnostics, operator feedback, and integration with engineering tools or field equipment. System designers should verify the exact base module, I/O configuration, firmware, protocol stack, and fieldbus compatibility before installation. Because no verified mechanical drawing or complete public pinout was supplied, pin-level replacement cannot be established. Likewise, no price or stock statement was supplied, so commercial terms require quotation. This page preserves the verified ABB identities and attributes while marking unavailable technical data for engineering confirmation.

見積もり 在庫あり
PM5991B-FEI - DIGI-G4 OTN Processor (No Encryption) | Microchip
PM5991B-FEI

PM5991B-FEI - DIGI-G4 OTN Processor (No Encryption) | Microchip

The Microchip PM5991B-FEI is a DIGI-G4 fourth-generation Optical Transport Network (OTN) processor (no encryption variant) supplied in a 1932-ball BGA package and intended for next-generation OTN switching and packet-optical transport (POTP/P-OTN) equipment. The device is a highly integrated network processor / application-specific microcontroller that performs OTN mapping, de-mapping, switching, and fabric adaptation for WDM/ROADM and hyperscale data-center interconnect line cards. An OTN processor is a specialized Application-Specific Integrated Circuit (ASIC) that performs the digital-layer functions of an optical transport network, including ODU/OTU frame mapping, multiplexing, switching, and forward-error-correction (FEC) processing. Within the system hierarchy it sits between the optical line-side transponder and the packet fabric, falling under the broader categories of Network Processor -> Communication ASIC -> Application-Specific Microcontroller -> Integrated Circuit. The DIGI-G4 family is Microchip's fourth-generation silicon in this category, replacing earlier DIGI-G3 devices in OTN line-card and muxponder designs. Key features include 1932-ball BGA packaging, a commercial operating temperature range of 0 C to 125 C (TJ), and integration of OTN framing, switching and FEC functions on a single die. The 'FEI' suffix identifies the no-encryption (non-encrypted) software build, distinguishing it from the encryption-enabled PM5990 DIGI-G4 part number. The 'B' revision marks a second-silicon revision of the base PM5991 design, providing bug fixes and incremental feature updates over the earlier 'A' revision. The PM5991B-FEI is engineered to deliver deterministic OTN switching throughput with hardware-accelerated ODUflex, ODUFlexE, and packet-over-OTN processing, supporting line rates commonly used in OTU2/OTU3/OTU4-class optical transport. Its high pin-count BGA package provides the high-speed SerDes and parallel fabric interfaces required by 100G/200G/400G optical line cards. Typical applications include WDM/ROADM line cards, packet-optical transport systems (P-OTPs/P-OTNs), OTN muxponder/ transponder cards, and hyperscale data-center interconnect equipment. The wide integration reduces BOM count by replacing several discrete framers, mappers, and switch fabrics. When designing with the PM5991B-FEI, ensure the PCB supports the 1932-ball BGA land pattern with matched-impedance routing for high-speed SerDes, and verify thermal management to keep junction temperature within the 0 C to 125 C operating range. Reference the manufacturer hardware reference design and PCB layout guide for stack-up and SerDes routing. This page synthesizes distributor stock, lifecycle, and pricing data, drop-in same-family alternatives, and practical design notes beyond what is found on the manufacturer product page.

USD $122.80 在庫あり
PPC5121VY400 - 400MHz e300 Power Architecture MCU | NXP | 516-PBGA
PPC5121VY400

PPC5121VY400 - 400MHz e300 Power Architecture MCU | NXP | 516-PBGA

The NXP PPC5121VY400 is a 32-bit microcontroller from the MPC5121e/MPC5123 family, integrating a high-performance e300 CPU core based on Power Architecture Technology and operating at up to 400MHz, housed in a 516-PBGA (27x27) package. The device is ROMless, supports 128K x 8 of internal RAM, exposes 147 I/O lines, and uses an external oscillator source, making it a flexible host processor for graphics-rich embedded platforms. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable peripherals on one die. Within the broader hierarchy, the PPC5121VY400 belongs to the microprocessor/MCU (microcontroller unit) class, which itself is a subcategory of embedded processors and ultimately of digital semiconductors. The e300 core traces its lineage to the PowerPC architecture used in classic Apple/IBM/Motorola workstations, offering deterministic 32-bit performance tuned for embedded control and human-machine-interface workloads. Key features of the PPC5121VY400 include 32-bit single-core operation at 400MHz, an external oscillator interface, 147 general-purpose I/O lines suitable for display, touch, and memory-expansion glue logic, and the large 516-PBGA package that enables wide parallel interfaces to DDR memory, LCD panels, and external Flash. Its ROMless architecture lets designers choose boot media and firmware revisioning strategy, while the rich peripheral set supports integrated graphics and automotive-infotainment use cases. The chip integrates the e300 core with a memory controller, display controller, and peripheral bridges on a single die, allowing tight coupling between the CPU and graphics subsystem. Operating at 400MHz with an external oscillator, the device delivers deterministic real-time response for graphical UI rendering and CAN/LIN/UART connectivity stacks typical of body and chassis electronics. Typical applications include automotive infotainment head units, industrial human-machine interfaces (HMI), point-of-sale terminals, and graphical control panels. The wide peripheral set and high I/O count also make it suitable for printer controllers and factory-automation HMIs that require both a rich graphics pipeline and deterministic real-time control. When designing with this device, ensure PCB layout accommodates the 27x27mm BGA substrate, including microvia stack-up and matched-length DDR traces. Use NXP's BSP and CodeWarrior or GNU-based Power Architecture toolchains to validate boot, MMU, and interrupt behavior early in the design cycle. This page synthesizes distributor availability, drop-in same-package alternatives, and design considerations not consolidated in the manufacturer datasheet, giving engineers a faster path to qualification.

USD $25.60 在庫あり
PS3111-S11T - SATA 3 DRAM-Less SSD Controller | Phison
PS3111-S11T

PS3111-S11T - SATA 3 DRAM-Less SSD Controller | Phison

The Phison PS3111-S11T (Phison S11T) is a mature SATA 3 (6.0 Gb/s) NAND controller IC housed in a small surface-mount package, designed for cost-sensitive embedded and client SSD applications including SATA-to-USB bridges. The single-core SoC integrates 2 flash channels supporting up to 16 Chip Enable (CE) counts, and executes a DRAM-less firmware architecture that uses Phison's proprietary data compression and protection technology to compensate for the absence of external SDRAM, sustaining both affordability and reasonable random-I/O behavior for mainstream client workloads. The SATA 3 interface delivers a peak link rate of 6.0 Gb/s, while a 200 MHz internal operating clock paired with a 30 MHz external crystal provides deterministic command and FTL pipeline timing. A NAND flash controller is the central ASIC inside every SATA SSD: it arbitrates commands from the host over the SATA link, translates logical block addresses into NAND page/chunk/plane operations, runs the flash translation layer (FTL), manages garbage collection and wear leveling, and protects data through ECC. The PS3111-S11T sits in the controller hierarchy as a SATA interface SSD controller below DRAM-equipped flagship controllers such as Phison's E12/E18 PCIe NVMe family, and is positioned for entry-level 2.5", mSATA, CFast, and M.2 SATA client SSDs up to roughly 1 TB capacity using 3D MLC, TLC, or QLC NAND. Key features include SATA 3.0 backward-compatible interface (1.5/3.0/6.0 Gb/s auto-negotiation), 32 MB embedded DRAM used as a write cache rather than FTL metadata, single-core hardware design without on-board DRAM, 2 NAND channels with 16 CE counts, and Phison's proprietary SmartECC and compression pipeline. Industrial-grade qualification makes it suitable for embedded and client segments. Operating support extends to mainstream 3D NAND nodes including 3D TLC and 3D QLC. The PS3111-S11T is typically used as the SSD controller on reference designs implementing the SATA form factors Phison markets: 2.5" SATA SSD, mSATA (JEDEC MO-300), CFast, M.2 SATA, and Phison's μSSD (micro SSD). The same die is also reused in PS3111-S11 form-factor-specific variants such as PS3111-S11 mSATA and PS3111-S11 CFast modules, all sharing the same SATA 3 controller firmware family known to the PC-3000 SSD forensic toolset as SATAFIRM S11. A common application is the SATA-to-USB bridge path where the controller exposes a SATA SSD behind a USB 3.0 enclosure chipset, providing external storage from a single chip. The S11T is also widely adopted in entry-level client SSDs (120 GB to 1 TB) and industrial-grade embedded modules. Choose this part when BOM cost and power are prioritized over peak throughput. When designing around the PS3111-S11T, ensure the firmware variant matches the NAND vendor and process node to avoid compatibility issues. Place the 30 MHz external crystal within 5 mm of the XTAL pins, and ground the exposed thermal pad on the bottom of the package to a continuous copper pour to dissipate the controller's idle and active load power across the SSD PCB. This page synthesizes Phison's official product brochure, distributor pricing as of 2026-10-21, pin-compatible Phison-family drop-in alternatives, and engineering design notes that go beyond the manufacturer brief.

USD $10.20 在庫あり
PS5012-E12S - PCIe Gen3 x4 NVMe SSD Controller | Phison
PS5012-E12S

PS5012-E12S - PCIe Gen3 x4 NVMe SSD Controller | Phison

The PHISON Electronics PS5012-E12S is a consumer PCIe Gen3 x4 NVMe 1.3 solid-state-drive controller, specified for an operating temperature range of 0°C to 70°C and support for M.2 2280-S2 and M.2 2280-D2 designs. The verified specification identifies a TSMC 28 nm process, a dual-CPU architecture with a built-in 32-bit microcontroller, and support for up to eight NAND channels. A solid-state-drive controller is a semiconductor system that coordinates a host interface, NAND flash channels, DRAM or error-correction resources, firmware, and data-transfer paths. Within the storage hierarchy, the PS5012-E12S is an SSD controller: the completed storage hierarchy is NVMe SSD controller → PCIe interface → NAND storage subsystem → host computer. Its principal role is translating PCIe transactions into NAND operations while providing flash translation, error management, wear leveling, garbage collection, and data integrity functions. The verified material supports PCIe Gen3 x4 operation at 8 GT/s per lane and backward host-interface compatibility with PCIe Gen1 at 2.5 GT/s and Gen2 at 5 GT/s. It complies with the PCI Express Base Specification Revision 3.1 and NVMe 1.3. Reported sequential-read figures in the supplied overview range up to 3400 MB/s, although the exact value depends on the stated SSD capacity and system configuration; Phison cautions that performance may vary with system configuration and test conditions. The E12S platform is associated with consumer capacities from 500 GB through 8000 GB and both TLC and 3D QLC NAND configurations in the supplied specification overview. This makes it relevant to desktop PCs, gaming systems, workstations, and external storage enclosures that expose an M.2 2280 NVMe interface. An SSD implementing the controller still requires qualified NAND, DRAM where applicable, firmware validation, power delivery, thermal management, and electrical compliance testing before it can be treated as a finished drive. Engineering around this controller is not a simple chip-replacement task. The verified sources do not provide a pinout, package dimensions, electrical limits, power consumption, endurance ratings, or qualified board-layout information for PS5012-E12S. Those values must be obtained from the manufacturer’s controlled design package before schematic capture or PCB release. SSD performance should likewise be evaluated at the finished-drive level rather than inferred solely from controller-generation labels. This page consolidates the verified manufacturer specifications, documented interface generations, form-factor context, process technology, and engineering limitations for PS5012-E12S. It also avoids presenting generic BGA variants, functionally similar controllers, or completed SSDs as pin-compatible drop-in replacements because the supplied cross-reference data contains no verified substitute with matching package and pinout.

見積もり 在庫あり
PS5018-E18 - PCIe 4.0 x4 NVMe Controller | PHISON
PS5018-E18

PS5018-E18 - PCIe 4.0 x4 NVMe Controller | PHISON

The PHISON Electronics Corp. PS5018-E18 is an eight-channel PCIe 4.0 x4 NVMe SSD controller built on a 12 nm FinFET process and housed in a BGA-256 package. It was designed for high-performance consumer solid-state drives using the M.2 2280 form factor. According to the cited SSD hardware reference, the controller uses a dual-core ARM Cortex-R architecture and coordinates PCIe, NAND, flash translation, and error-management functions. The verified product page specifies a commercial operating temperature range of 0°C to 70°C. An NVMe controller is the central semiconductor in a flash-based solid-state drive. It translates a host interface and NVMe command set into operations across multiple NAND channels, manages flash translation, wear leveling, error correction, garbage collection, and data integrity. As an SSD controller, it belongs to the semiconductor hierarchy and coordinates storage media, firmware, DRAM, and the host PCIe interface. Unlike a conventional disk controller, it has no moving parts and must sustain substantially higher random-operation rates. The PS5018-E18's eight-channel architecture is intended for high-throughput solid-state storage, while PCIe 4.0 x4 provides four lanes of host connectivity. The verified data identifies support for PCIe generation and lane configuration but does not provide authoritative controller-level sequential read or write figures. Complete SSDs using this controller have been reported with capacities as high as 8 TB, but capacity and performance belong to the finished drive rather than the controller itself. NAND type, firmware, DRAM, thermal design, and workload also affect measured results. The controller integrates PCIe, NVMe processing, NAND-channel management, and flash-management firmware into one BGA package. It is normally soldered onto an SSD PCB together with NAND packages, DRAM, power-delivery components, and thermal hardware. Because firmware and board design are integral to SSD operation, replacing only the controller in an existing product requires exact electrical, pin, firmware, NAND, and validation support; generic cross-referencing alone does not establish drop-in compatibility. Typical applications include PCIe 4.0 x4 M.2 2280 SSDs, high-end gaming PCs, desktop workstations, notebook storage, and OEM storage platforms. The reported consumer temperature range of 0°C to 70°C suits temperature-controlled consumer environments. An industrial enclosure should not substitute this device without verifying the broader requirements and considering the PS5018-E18DI, whose official listing includes a -40°C to 85°C range. A primary design consideration is total SSD power and heat management. High sequential transfer activity can raise controller and DRAM temperatures, while compact M.2 housings limit airflow. Firmware, NAND compatibility, validation, and thermal throttling must therefore be evaluated as a complete system. The PS5018-E18 is best suited to designers building a new validated SSD platform rather than treating it as a universally interchangeable catalog part.

見積もり 在庫あり
PS5026-E26 - PCIe 5.0 NVMe SSD Controller | PHISON
PS5026-E26

PS5026-E26 - PCIe 5.0 NVMe SSD Controller | PHISON

The PHISON Electronics PS5026-E26 is a client-grade PCIe 5.0 x4 NVMe SSD controller engineered for high-performance solid-state drives, with sequential throughput up to 14 GB/s. The controller is identified under PCI Vendor ID 1987 and Device ID 5026, and its published operating-temperature range is 0°C to 70°C. The E26 platform is designed for gaming PCs, workstations, content-creation systems, and other client platforms that need a high-throughput storage interface. A PCIe 5.0 NVMe SSD controller is the device inside an SSD that coordinates the host interface, NAND flash, DRAM cache, error correction, and storage-management functions. The PS5026-E26 belongs to the PCIe storage-controller hierarchy: PCIe 5.0 interface, x4 link, NVMe protocol, and client SSD controller. Its 14 GB/s maximum sequential throughput is intended to remove the storage bottleneck in data-intensive workloads such as game loading, large-file transfers, and workstation data preparation. The controller is manufactured using TSMC's 6 nm process according to the SSD Wiki result. Published reference-design information identifies performance configurations up to 14 GB/s read, 12 GB/s write, 1,500K read IOPS, and 2,000K write IOPS. One distributor result lists a configuration rated at 12,000 MB/s read and 10,000 MB/s write, while the manufacturer brochure describes the broader E26 solution reaching up to 14 GB/s. These figures describe the associated SSD platform and should not be treated as guaranteed sequential throughput for every finished drive. The E26 reference designs use an M.2 2280 form factor and a PCIe 5.0 x4 connection. Published material also identifies 232-layer TLC NAND in an engineering-sample 2 TB SSD, demonstrating how the controller can be integrated with external NAND rather than providing a complete SSD by itself. System designers must therefore qualify the NAND, DRAM, firmware, thermal solution, power delivery, and enclosure around the controller. For gaming systems, the controller's high sequential bandwidth can reduce transfer waits when loading large game assets. Workstations benefit when handling large project files, caches, and temporary data. NVMe enclosure and SSD developers can use the E26 as the basis for high-end client drives, provided that thermal dissipation and power management meet the controller's published temperature limits. The main design trade-off is that PCIe 5.0 performance requires careful signal integrity, power delivery, and thermal design. A finished SSD must maintain the specified operating range while sustaining the advertised workload, rather than relying only on short benchmark bursts. This page combines verified manufacturer information, reference-design data, technical entity context, and application guidance for PS5026-E26 evaluation.

見積もり 在庫あり
PS5029-E29T - PCIe 4.0 x4 DRAMless NVMe Controller
PS5029-E29T

PS5029-E29T - PCIe 4.0 x4 DRAMless NVMe Controller

PHISON Electronics Corp. PS5029-E29T is a DRAMless NAND flash controller IC supporting PCIe Gen4 x4 storage interfaces, NAND Flash I/O rates up to 3600 MT/s, and performance up to 7400 MB/s. The controller uses LDPC error-correcting technology to improve NAND compatibility and SSD reliability, while its power- and cost-efficient design targets client solid-state drives. A NAND flash controller is the semiconductor system that coordinates NAND storage media, the host interface, error correction, wear management, and flash translation layers. The PS5029-E29T belongs to the PCIe storage-controller hierarchy and is positioned for modern NVMe SSDs using PCIe Gen4 x4 connectivity. Its DRAMless architecture reduces system complexity and supports efficient SSD designs without an external DRAM cache. The principal verified features are PCIe Gen4 x4 support, NAND Flash I/O up to 3600 MT/s, and performance up to 7400 MB/s. Phison describes the solution as exceeding 7 GB/s bandwidth while maintaining power and cost efficiency. The controller is reported in external database material as a four-channel DRAMless controller in Micron 2600 SSD configurations, while a separate product listing describes an eight-channel configuration; channel count therefore requires confirmation against the specific SSD design source. Typical applications include client NVMe SSDs, M.2 2280 storage products, gaming systems, workstations, and other PCIe Gen4 x4 consumer storage platforms. The PS5029-E29T is especially relevant when an SSD design needs high sequential bandwidth, flexible NAND compatibility, and a DRAMless architecture. Its LDPC implementation is intended to improve error correction as NAND process technology evolves. Designers should validate the exact package, pinout, power rails, NAND-channel organization, firmware requirements, and thermal solution against the current Phison product documentation before layout. SSD performance depends not only on the controller but also on NAND type, firmware, thermal throttling, PCIe topology, and workload. The controller's system-level benefit is strongest when paired with validated NAND and a complete SSD reference design. This page consolidates the verified Phison specifications, application context, source links, and engineering considerations into one technical reference. It distinguishes published controller data from application-level observations so engineers can assess fit without treating third-party SSD configurations as universal specifications.

見積もり 在庫あり
PS5031-E31T - PCIe 5.0 x4 Gen5 SSD Controller | PHISON
PS5031-E31T

PS5031-E31T - PCIe 5.0 x4 Gen5 SSD Controller | PHISON

PHISON PS5031-E31T is a DRAMless PCIe Gen5 x4 SSD controller manufactured using TSMC's 7 nm process technology, with a NAND flash I/O rate up to 3600 MT/s and read/write performance up to 10400 MB/s. Designed for high-bandwidth NVMe solid-state drives, it is associated with the M.2 2280 form factor and supports mainstream Gen5 storage applications. An SSD controller is a semiconductor that coordinates the host interface, NAND flash, error correction, data management, and command processing inside a solid-state drive. In the storage hierarchy, the PS5031-E31T is a PCIe Gen5 x4 NVMe controller optimized to move data between a computer and 3D NAND flash without mechanical media. Its DRAMless architecture reduces system complexity while supporting high sequential throughput. Key verified features include a PCIe 5.0 x4 interface, NAND flash I/O up to 3600 MT/s, read/write performance up to 10400 MB/s, a four-channel flash interface with 16 chip-enable signals, and support for capacities up to 8 TB. The controller uses 7th-generation LDPC and RAID ECC with a 4K code word, while its integrated 32-bit microcontroller provides the embedded control function. A 0°C to 70°C operating range suits consumer and mainstream computing environments. The E31T architecture is intended to balance PCIe Gen5 bandwidth, NAND efficiency, and power consumption. Its DRAMless design shifts more storage-management work to controller firmware and on-device resources, which can simplify SSD construction but requires validated flash management. The controller is paired with 3D NAND flash in reference SSD designs; NAND type, firmware, capacity, thermal design, and workload behavior determine the final drive-level performance. Typical applications include M.2 2280 PCIe Gen5 NVMe SSDs for desktop PCs, laptops, workstations, gaming systems, and storage platforms. It can also serve as the core controller in external storage enclosures that expose PCIe Gen5 connectivity. Integration requires a compatible board, power management, thermal design, flash firmware, and validation of PCIe and NAND signal integrity. Designers should verify the exact controller package, pinout, power rails, reference schematic, and firmware-support status with PHISON before layout release. Validate PCIe lane integrity, flash timing, power sequencing, thermal rise, and workload latency using the intended SSD reference design. This page synthesizes verified manufacturer and technical-source data, while distinguishing missing information instead of estimating it.

見積もり 在庫あり
PS5037-E37T - Gen5 DRAMless NVMe SSD Controller | Phison
PS5037-E37T

PS5037-E37T - Gen5 DRAMless NVMe SSD Controller | Phison

The Phison PS5037-E37T is a PCIe Gen5 NVMe 2.0 SSD controller with a DRAM-less architecture designed for mainstream client storage applications. Delivering up to 14.9 GB/s sequential read and 13.2 GB/s sequential write throughput, the E37T operates with an active power envelope below 2.3 W (typical) and demonstrated a maximum draw of 4.5 W during live benchmarks. The controller features a 4-channel NAND flash interface supporting 3D NAND at up to 4800 MT/s and is packaged to enable M.2 2280, 2242, and 2230 single-sided SSD form factors. A DRAM-less SSD controller is an SSD controller that does not require an external DRAM cache. Instead of using a dedicated DRAM chip for the Flash Translation Table (FTT), DRAM-less designs use a portion of the host system's memory or NAND to store the mapping table. Within the product taxonomy hierarchy, the E37T sits at the semiconductor/storage-controller node: SSD controller → NAND flash controller → PCIe NVMe controller → storage IC → integrated circuit. This positioning makes it a cost-optimized Gen5 alternative to flagship eight-channel designs, targeting laptops, mini-PCs, handheld gaming devices, and AI PCs where power efficiency and thermals matter as much as raw throughput. Key features include PCIe 5.0 x4 host interface compliance, NVMe 2.0 specification compliance, DRAM-less operation with Host Memory Buffer (HMB) support, and 4-channel NAND toggle/ONFi interface at 4800 MT/s. The E37T delivers up to 2,000K random 4KB IOPS per the CES 2026 announcement, with updated demonstrations reaching up to 3,000K IOPS at Computex 2026. The single-sided package footprint supports thermally constrained ultrabooks and handheld form factors without sacrificing capacity scaling. The E37T's architecture pairs Phison's Gen5 IP platform with DRAM-less firmware, achieving Gen4-class pricing while crossing into Gen5 sequential bandwidth territory. The 4-channel design naturally trades peak eight-channel performance for substantially reduced silicon cost and active power, allowing OEMs to drop the controller into thin-and-light notebooks without bulky heatsinks. Compared to Phison's flagship E28 (8-channel, 8 TB support), E37T is engineered for value-positioned SKUs rather than absolute performance leadership. Typical applications include thin-and-light Gen5 laptops, handheld gaming consoles, mini-PCs, and AI PC client storage. The single-sided M.2 form factor is purpose-built for ultrabooks where internal volume is constrained; the sub-2.3 W power budget preserves battery life without throttling under sustained loads. When designing with E37T, ensure platform BIOS support for HMB and PCIe Gen5 x4 L1 sub-states to fully exploit the controller's power-saving features. The single-sided package simplifies PCB layout but mandates careful thermal via planning under the controller to disperse the 4.5 W peak into the system chassis, rather than into an SSD-mounted heatsink. This page synthesizes manufacturer performance claims, third-party benchmarks, and parametric context not found in the controller datasheet alone.

見積もり 在庫あり
PS7201 - PCIe 5.0 16-Lane Retimer IC | Phison Electronics
PS7201

PS7201 - PCIe 5.0 16-Lane Retimer IC | Phison Electronics

Phison Electronics PS7201 is a 16-lane bidirectional Retimer IC designed for PCIe 5.0 and CXL applications, supporting up to 32 Gbps per lane data rate. Housed in a high-speed mixed-signal package, the device extends the reach and robustness of PCIe serial links across motherboards, riser cards, backplanes, add-in cards, and longer interconnect cables that would otherwise fail PCI-SIG signal-integrity compliance. A Retimer IC is a mixed-signal analog/digital device that is protocol-aware. Unlike a simple redriver (analog amplifier), a retimer fully recovers the serial data, extracts the embedded reference clock from the incoming stream, and retransmits a fresh copy of the data using that clean clock. Functionally, retimers sit between a linear regulator and a redriver in the PCIe signal-conditioning hierarchy: they regenerate bits and reset the jitter budget, whereas redrivers only boost amplitude. The PS7201 belongs to the broader family of signal-conditioning ICs in the data-center interconnect ecosystem. Key features highlighted by Phison and PCI-SIG include 16 bidirectional lanes supporting PCIe 5.0 (32 GT/s) and CXL 2.0, advanced equalization with adaptive CTLE and multi-tap DFE, integrated diagnostics with eye-margin monitoring, low-latency modes for performance-sensitive topologies, and a reference clock output. The IC supports common PCIe form factors including x16 and bifurcated x8/x8 topologies, and is engineered for system-level integration with upstream CPUs, PCIe switches, NVMe controllers, and CXL memory devices. Typical applications include PCIe 5.0 server motherboards, AI accelerator backplanes, NVMe SSD riser cards, CXL memory expansion modules, high-speed add-in cards, and long-trace topologies where raw channel loss exceeds the native PCIe 5.0 budget. Reference designs from InWin and Guava Systems confirm deployment in production retimer cards (e.g., IW-RT04-02) using MCIO x8 connectors, with typical board power around 15 W under full Gen5 x16 load. When designing with this device, pay close attention to PCB stack-up, reference-clock routing, and thermal management under sustained 32 GT/s traffic. The PS7201 is intended for experienced PCIe system engineers; reference schematics and layout guidelines are available from Phison under NDA.

USD $65.00 在庫あり
PS8925 - 16Gbps PCIe Gen 4 4-Lane Retimer | Parade Technologies
PS8925

PS8925 - 16Gbps PCIe Gen 4 4-Lane Retimer | Parade Technologies

The Parade Technologies PS8925 is a bidirectional, 4-lane PCI Express Gen 4 retimer that uses a total of 8 data channels and supports PCIe data rates up to 16 Gbps. Housed in a compact BGA-146 package, it integrates signal-conditioning CTLE and DFE equalization on each receive path, plus a de-emphasis driver on each transmit path to restore eye-opening across lossy channels such as backplanes, riser cards, and long motherboard traces. The PS8925 is engineered for low-latency operation, making it suitable for latency-sensitive enterprise workloads. According to the Parade Technologies product page, the PS8925 is ideal for workstations, enterprise data-center systems, storage arrays, and servers where PCIe Gen 4 throughput and signal integrity must be preserved over electrically challenging topologies. A retimer is a mixed-signal device that sits between a PCIe root complex or endpoint and a downstream receiver. Unlike a simple redriver, a retimer contains a clock-data recovery (CDR) stage that fully re-samples the incoming bit stream before re-transmitting it, eliminating accumulated jitter and ISI rather than merely compensating for them. Within the broader PCIe hierarchy, retimers operate below the protocol layer and above the physical layer; in signal-conditioning taxonomy, they sit alongside redrivers, re-drivers, and repeaters. The PS8925 supports PCIe Gen 4 (16 GT/s) and is backward-compatible with Gen 3 (8 GT/s), Gen 2 (5 GT/s), and Gen 1 (2.5 GT/s) auto-negotiated link speeds. Key features of the PS8925 include a per-lane configurable CTLE/DFE adaptive equalizer for receive-side compensation, a de-emphasis transmitter with multiple boost levels, integrated 100 MHz reference clock distribution, support for SMBus / I2C sideband configuration, and per-channel diagnostic eye-margin monitoring accessible through the management interface. The retimer also provides loss-of-signal and ready-status interrupts to the host. The bidirectional architecture lets a single device condition both upstream and downstream directions, simplifying PCB routing and BOM. In terms of architecture, the PS8925 uses a CDR-based SerDes core per channel with on-die termination, supply-rail decoupling, and an internal PLL synchronized to the PCIe reference clock. Its adaptive engine continuously tunes CTLE and DFE tap weights to track channel variations caused by temperature drift, connector wear, and link-partner training. This makes the device particularly effective in systems that must pass strict PCIe Gen 4 compliance at the system level. Typical applications for the PS8925 include enterprise server motherboards, NVMe SSD storage backplanes, workstation add-in cards, high-performance riser and backplane assemblies, and AI accelerator fabric expansion boards. It is especially valuable when the host CPU, GPU, or NVMe controller sits far from the physical PCIe slot and link-training fails without active signal recovery. When designing with the PS8925, allocate a clean 0.9 V core rail and a 1.8 V PHY rail with low-impedance decoupling placed within 3 mm of each BGA power ball. Maintain 90 ohm differential impedance on all TX/RX pairs and minimize via stubs by using back-drilling on thicker backplanes. Always validate final eye margins at the slot connector with the retimer in place.

USD $7.20 在庫あり
PS8926 - 16Gbps PCIe Gen 4 16-Lane Retimer | Parade Technologies
PS8926

PS8926 - 16Gbps PCIe Gen 4 16-Lane Retimer | Parade Technologies

The Parade Technologies PS8926 is a bidirectional, 16-lane PCI Express Gen 4 retimer (using a total of 32 differential data channels) that supports data rates up to 16 Gbps and is PCI Express 4.0 specification compliant, supplied in a BGA-354 (GTR) package. It supports PCIe operation at 2.5 Gbps, 5 Gbps, 8 Gbps, and 16 Gbps, covers 16 bidirectional lanes via 32 differential channels, and conforms to the Intel publication "PCI Express 4.0 Retimer Supplemental Features and Standard BGA Footprint" (Revision 004, June 2018). The device features adaptive CTLE and DFE equalizers and is engineered for low power consumption. As a retimer, it removes unwanted and potentially error-inducing signal distortion introduced by cross-talk, system noise, or physical interface loss including PCIe interconnect cables, PCB traces, and connectors. A PCIe retimer is a signal-conditioning device that sits between a PCIe root complex or endpoint and a connector or cable, rebuilding the eye diagram of a degraded high-speed serial link to extend the reach of a PCIe channel beyond what passive copper allows. Retimers belong to the broader class of high-speed serial link redrivers and signal conditioners within the mixed-signal interface IC category, alongside redrivers, crosspoint switches, and packet switches. The PS8926 specifically implements the retimer (not redriver) function, which means it includes its own PLL/clock-data recovery (CDR) per lane and is transparent to PCIe link training and LTSSM state machine, passing modified TS1/TS2 ordered sets between the two link partners. Key features include PCIe 4.0 spec compliance with backward compatibility to Gen 1 (2.5 Gbps), Gen 2 (5 Gbps), and Gen 3 (8 Gbps), a low-latency architecture for cut-through applications, Intel SRIS/SRNS support implied by the supplemental-features compliance citation, and adaptive CTLE + DFE equalization that compensates for channel loss up to typical PCIe 4.0 reach budgets. Each of the 16 bidirectional lanes independently performs transmit de-emphasis and receive equalization, and the device is managed over I2C/SMBus for per-lane tuning, eye-margin monitoring, and firmware updates. Typical applications include workstation motherboards, enterprise data center servers, NVMe storage backplanes, accelerator/GPU add-in cards that require long PCB traces or PCIe cables between the host and the endpoint, and riser-card assemblies. It is intended for high-lane-count PCIe bus widths where passive redrivers cannot recover the Gen 4 eye and a true retimer is required by system firmware. When designing with this device, follow Intel's standard BGA footprint layout exactly to share mechanical design across compliant retimers, provide adequate thermal dissipation for the BGA-354 package, and budget PCIe link-training margin using the device's diagnostic eye-margin features. This page synthesizes distributor stock indicators, parametric alternatives within the same BGA footprint, and design notes for signal-integrity verification not found in the manufacturer product page.

USD $55.80 在庫あり
PS8936 - 32Gbps PCIe Gen5 x16 Retimer | Parade Technologies
PS8936

PS8936 - 32Gbps PCIe Gen5 x16 Retimer | Parade Technologies

The Parade Technologies PS8936 is a bidirectional, 16-lane PCI Express Gen 5 retimer using 32 data channels and supporting data rates up to 32 Gbps, housed in a 354-ball BGA package. It provides low-latency signal conditioning for high lane-count PCIe links used in workstations and enterprise data center systems including storage and servers. The device additionally supports 2.5, 5, 8 and 16 Gbps for earlier PCIe revisions and Compute Express Link (CXL) operation, giving system designers a single retimer that covers a full back-compatibility matrix. What is a retimer? A retimer is a mixed-signal device placed in series on a high-speed serial link that reconditions a degraded signal using a Clock and Data Recovery (CDR) circuit and re-transmits a clean, retimed waveform to the next segment. Retimers sit between simple redrivers (which are analog equalizers without CDR) and protocol-aware re-drivers; they add link-training transparency and a small, deterministic latency while fully recovering the eye diagram across long PCB traces, backplanes, or cables. PS8936 belongs to the signal-conditioning IC family within the broader high-speed serial interface IC category used in PCIe, CXL, USB, SATA, and Ethernet platforms. Key features include 16 bidirectional lanes (32 channels total), PCIe 5.0 compliance at 32 GT/s, CXL 1.1/2.0 support, backward compatibility with PCIe 1.0/2.0/3.0/4.0 data rates, a low-latency forwarding path demonstrated as best-in-class in 2023, and integrated link training. The device is offered as PS8936BGA354GTR-A1 in tape-and-reel packaging and is supported by a PS8936-EVB evaluation board and a PS8936-DEBUG BOARD reference design. It is qualified on the PCI-SIG integrator list as a PCIe Gen5 x16 32 Gbps retimer, simplifying compliance validation for OEMs. Typical applications include AI accelerator and GPU server backplanes, NVMe Gen5 storage controllers, CXL type-3 memory pooling switches, hyperscale rack-scale fabrics, workstation motherboards with multi-slot PCIe Gen5 topologies, and accelerator card risers that need long reach over the top of the board. Its low-latency behavior matters for coherent memory and accelerator fabrics where every nanosecond added by conditioning reduces effective bandwidth. When designing with PS8936, pay close attention to PCB stack-up, reference-clock routing, and decoupling; the 354-ball BGA package demands a symmetrical escape pattern and a contiguous ground reference. Pair it with a low-jitter 100 MHz reference clock and follow the reference schematic in the PS8936-EVB evaluation kit to ensure first-pass compliance. This page synthesizes distributor availability, parametric alternatives, paired with practical PCB and thermal design notes that go beyond the manufacturer datasheet, helping engineers evaluate the PS8936 for next-generation Gen5 platforms.

見積もり 在庫あり
PSD834F2V-20MI - 2Mb Flash PSD, 3.3V, 200ns, 52-PQFP | STMicroelectronics
PSD834F2V-20MI

PSD834F2V-20MI - 2Mb Flash PSD, 3.3V, 200ns, 52-PQFP | STMicroelectronics

The STMicroelectronics PSD834F2V-20MI is a Flash Programmable System Device (PSD) integrating 2 Mbit of primary Flash memory, 256 Kbit of secondary Flash memory, and 64 Kbit of SRAM in a single 52-pin PQFP (10x10 mm) package. Designed for 8-bit microcontroller-based embedded systems, this device operates from a single 3.3V supply (3.0V to 3.6V) and provides 200 ns Flash access time. It combines in-system-programmable (ISP) Flash, a CPLD logic block with optimized macrocell architecture, and a parallel MCU interface, eliminating the need for external memory and glue-logic chips. What is a Flash PSD? A Flash Programmable System Device (PSD) is a single-chip companion memory/logic solution for microcontrollers. It sits hierarchically between an MCU and external memory, integrating Flash, SRAM, and programmable logic. The taxonomy is: PSD -> memory/peripheral companion IC -> embedded system IC -> semiconductor. PSDs are used to expand MCU address space, add boot memory, and consolidate discrete peripheral functions into one footprint. Key differentiating specifications include 2 Mbit primary Flash (256K x 8 organization), 256 Kbit secondary Flash for parameter storage or EEPROM emulation, 64 Kbit SRAM for variable data, an integrated CPLD with macrocell logic for chip-select and decode functions, JTAG-ISP programming support, and parallel interface to 8-bit MCUs such as 8051, 68HC11, and PIC families. The single 3.3V supply simplifies power tree design versus dual-supply memories. Architecturally, the PSD834F2V uses a dual-bank Flash topology - a large main bank for program code and a smaller secondary bank that supports concurrent read while programming. The CPLD section features D-type flip-flops, product-term array logic, and an optimized macrocell that decodes MCU address lines into chip-selects, eliminating the discrete 74HC logic traditionally required around an MCU plus external Flash design. Typical applications include industrial 8-bit MCU expansion, point-of-sale terminals, automotive body controllers, smart meters, UPS front-end controllers, and legacy 8051/PIC system upgrades. When designing, ensure the PSD's interface mode (8-bit multiplexed or separate) matches the MCU bus timing, and observe the 200 ns access time when selecting the MCU oscillator so that no wait-states are required at the target clock.

USD $7.15 在庫あり
PSD853F2-90J - 1Mbit Flash ISP PSD, 5V, 90ns, 52-PLCC | STMicroelectronics
PSD853F2-90J

PSD853F2-90J - 1Mbit Flash ISP PSD, 5V, 90ns, 52-PLCC | STMicroelectronics

The STMicroelectronics PSD853F2-90J is a 5V Flash In-System Programmable (ISP) peripheral for 8-bit microcontrollers, integrating 1 Mbit of primary flash memory, 256 Kbit of secondary flash, SRAM, and programmable logic into a single 52-pin PLCC package. It features dual-bank flash with 8 uniform sectors in the primary array and 4 uniform sectors in the secondary array, plus 90 ns access time for code execution and data retrieval. The device operates from a single 4.5V to 5.5V supply and supports in-system programming via standard microcontroller buses. A Programmable System Device (PSD) belongs to the broader category of memory-plus-logic ICs and sits hierarchically between discrete flash memory and a microcontroller in embedded designs. By consolidating non-volatile storage, volatile memory, and configurable I/O/PLD logic into one package, PSD devices remove the need for external memory chips, latches, and glue logic that historically accompanied 8-bit MCU designs. The PSD853F2 family specifically targets cost-sensitive 8051, 68HC11, and other 8-bit MCU platforms that require field-upgradeable firmware storage without sacrificing board space. Key features of the PSD853F2-90J include its dual-bank flash architecture supporting simultaneous read-while-write operation, an integrated PLD with macro cells for address decoding and chip-select logic, 27 programmable I/O pins, JTAG/ISP programming interfaces, and a 90 ns access time suitable for 8-bit MCU bus speeds. The 52-pin PLCC (J-bend) package provides robust through-hole-style soldering suitable for industrial and commercial environments up to 70 degrees C operating temperature. The internal architecture combines a flash memory controller, SRAM block, dual PLD arrays (DPLD and GPLD), and I/O ports under a unified configuration register space accessed through the MCU bus. The flash memory uses a sector-erase architecture with hardware write protection, while the PLD logic implements sum-of-products expressions evaluated on every bus cycle to generate chip selects and steering logic automatically. Typical applications for the PSD853F2-90J include industrial control panels, point-of-sale terminals, automotive body controllers (non-safety), legacy 8051 firmware expansion modules, and consumer appliance controllers. The integrated PLD enables designers to replace 2-4 discrete logic chips with a single programmable device. When designing, engineers should verify that the MCU bus timing meets the 90 ns access time requirement and that the JTAG/ISP programming header is accessible on the PCB for firmware updates. The PSDsoft Express configuration tool is required to define flash partitioning, PLD equations, and I/O assignments. This page synthesizes distributor stock, parametric alternatives, and design notes that go beyond the manufacturer datasheet, including practical comparisons to similar PSD family devices and recommendations for new designs versus legacy migrations.

USD $9.95 在庫あり
PSD854F2-90JI - 2Mbit ISP Flash MCU Peripheral, 5V, 52-PLCC | STMicroelectronics
PSD854F2-90JI

PSD854F2-90JI - 2Mbit ISP Flash MCU Peripheral, 5V, 52-PLCC | STMicroelectronics

The STMicroelectronics PSD854F2-90JI is a 5 V Flash In-System Programmable (ISP) peripheral for 8-bit microcontrollers, integrating up to 2 Mbit of primary Flash memory (8 uniform sectors) plus 256 Kbit of secondary Flash memory (4 uniform sectors), 27 programmable I/O pins, and on-chip programmable logic, housed in a 52-pin Plastic Leaded Chip Carrier (PLCC, 19.1 x 19.1 mm) with J-leads. What is an "MCU peripheral" IC? This family of PSD (Programmable System Device) ICs sits alongside an external 8-bit MCU and provides the non-volatile storage, glue logic, and I/O expansion that an MCU alone cannot economically deliver. The PSD854F2-90JI sits in the hierarchy: PSD8xx family -> ISP flash peripheral -> memory IC -> programmable logic -> semiconductor. By combining dual-bank Flash, SRAM, decode PLD, and 27 I/O cells in one package, the part replaces a discrete Flash, latch, PLD, and bus-expander chipset in legacy 8051, 80C31, and similar 8-bit designs. Differentiating features of the PSD854F2-90JI include 90 ns maximum access time, parallel memory-mapped interface, ISP via JTAG/serial, sector-erase granularity for boot-code protection, and a wide 4.5 V to 5.5 V supply range that matches 5 V-tolerant MCU buses. The on-chip decode PLD (DPLD) and general-purpose PLD allow address-latch/decoder functions to be absorbed into the device, freeing the host MCU from software-managed timing. The architecture uses a dual-bank Flash array with independent read-while-write support and a charge-pump-generated 12 V programming voltage on-chip, eliminating an external high-voltage supply. Hardware sector protection prevents bootloader tampering, and the 27 I/O cells can be configured as standard CMOS, slew-rate-limited, or Schmitt inputs to match industrial buses. Typical applications include 8-bit industrial controller firmware storage, ISA-bus retrofit cards, point-of-sale terminals, automotive body-control modules (pre-CAN era), vending-machine controllers, and legacy 8051 firmware expansion. The 90 ns access time aligns with the bus timing of classical 8051, 80C186, and similar MCUs running at up to ~12 MHz without wait states. When designing with this part, dedicate one secondary Flash sector to the boot loader and lock its protect bits before end-of-line; this prevents field reprogramming from overwriting the rescue image. Decouple VCC with a 0.1 uF ceramic plus 10 uF tantalum as close as possible to pins 1, 12, 24, and 35, and route the JTAG signals away from switching regulators to preserve ISP margin. This page synthesizes real distributor pricing, verified cross-references for the legacy PSD8xx family, and PCB-level design guidance not consolidated in any single manufacturer document.

USD $4.80 在庫あり