集積回路

サブカテゴリ

📁 ADC/DAC 2364 製品 📁 アンプIC 497 製品 📁 オーディオコーデック 12 製品 📁 オーディオIC 2 製品 📁 クロック＆タイミング 131 製品 📁 DSP 906 製品 📁 データ収集IC 2 製品 📁 デジタルポテンショメータ 4 製品 📁 ディスプレイドライバ＆コントローラ 1 製品 📁 FPGA & CPLD 6536 製品 📁 インターフェースIC 901 製品 📁 LEDドライバ 1 製品 📁 ロジックIC 252 製品 📁 メモリIC 833 製品 📁 マイクロコントローラ 17339 製品 📁 マイクロプロセッサ 4 製品 📁 モータドライバ 1 製品 📁 その他 1 製品 📁 専用IC 14 製品 📁 ビデオIC 7 製品

製品 (29810)

XR34350ILTR - Multiprotocol RS-232/RS-485/RS-422 Transceiver | MaxLinear
XR34350ILTR

XR34350ILTR - Multiprotocol RS-232/RS-485/RS-422 Transceiver | MaxLinear

The MaxLinear XR34350ILTR is an advanced multiprotocol serial transceiver supporting RS-232, RS-485, and RS-422 standards in a 40-pin QFN (6x6 mm) package. It delivers integrated cable termination, four configuration modes, and up to 20 Mbps RS-485/RS-422 throughput. According to the MaxLinear datasheet, the device operates from a single 3.3 V or 5.0 V supply (±5%) and requires only four external 0.1 µF charge pump capacitors for full operation. An RS-485/RS-422 multi-protocol transceiver is a single-chip interface IC that allows one physical port to communicate over multiple serial standards by reconfiguring its drivers and receivers. This category sits within the broader family of serial transceivers (also known as line transceivers or bus transceivers), which are essential building blocks inside the interface ICs tier of a system. By consolidating three standards into one IC, multiprotocol transceivers reduce BOM count, save PCB area, and let a single hardware design talk to legacy RS-232 equipment, RS-485 multidrop buses, and RS-422 point-to-point links on demand. Key features include 1 transmitter / 1 receiver (1Tx / 1Rx) in RS-485/RS-422 half or full duplex, full DB9-equivalent 3Tx / 5Rx support in RS-232 mode, a dedicated diagnostic loopback mode, integrated cable termination resistors, and wide output swing for robust signal margins. High-speed drivers reach 20 Mbps in RS-485/RS-422 and 1 Mbps in RS-232 mode. Four configuration pins select the active protocol at power-up with no external switching components required. The architecture combines a charge-pump DC-DC converter (the four external capacitors double and invert the supply to generate the RS-232 driver rails) with differential line drivers and receivers. Wide output swing ensures compliance with RS-232 ±15 V signaling even when powered from 3.3 V rails, while the integrated termination resistors eliminate external RS-485 120 Ω bias networks on the bus. Typical applications include multiprotocol industrial fieldbus gateways, point-of-sale (POS) terminals that must handshake with both legacy RS-232 peripherals and modern RS-485 instruments, telecom base station control ports, building automation controllers, and any embedded system that needs to bridge between RS-232, RS-422, and RS-422 segments on a single connector. When designing with this part, place the four charge-pump capacitors as close to the C1–C4 pins as possible with low-ESR ceramic types, and keep the MODE/SHDN pins either tied or driven by GPIOs. Note that activating the integrated termination draws additional supply current; disable it when not in use to save power. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers quickly compare multiprotocol transceiver options for industrial-grade serial designs.

USD $4.41 在庫あり
XR4151CP-F - V/F Converter, 8-22V, 100kHz | MaxLinear
XR4151CP-F

XR4151CP-F - V/F Converter, 8-22V, 100kHz | MaxLinear

The MaxLinear XR4151CP-F is a monolithic voltage-to-frequency (V/F) and frequency-to-voltage (F/V) converter IC supplied in an 8-pin PDIP through-hole package. It accepts a single-ended analog input voltage of 0 to 10 V (or -10 V to 0 V with appropriate biasing) and produces a proportional output pulse train whose frequency is linearly related to the input amplitude. The maximum full-scale frequency is 100 kHz with a usable range of 1 Hz to 100 kHz and a typical linearity error of +/-0.05%. A voltage-to-frequency converter (V/F or VFC) is a mixed-signal building block that translates a continuous analog voltage into a stream of digital pulses whose repetition rate is precisely proportional to the input magnitude. VFCs sit within the broader hierarchy of analog-to-digital conversion techniques alongside successive-approximation ADCs, dual-slope integrating ADCs, and sigma-delta modulators, and are valued for their inherent monotonicity, excellent noise rejection, and galvanic isolation-friendly pulse output that can be transmitted through optocouplers or long cables. Key features of the XR4151CP-F include a supply voltage range of 8 V to 22 V, very high noise rejection, inherent monotonicity over the full dynamic range, a single open-collector output stage that can interface with CMOS/TTL logic, and the ability to operate in reverse as a frequency-to-voltage converter with a small number of external components. The -F suffix denotes the lead-free, RoHS-compliant version of the original XR4151CP, while both share the same die and pinout. The internal architecture consists of a precision current source, a high-gain operational amplifier, a comparator, and a one-shot timing network. The op-amp drives a current into an external RC network whose charging time determines output pulse width; this architecture eliminates the missing-pulse and non-monotonic errors that plague simple charge-pump VFCs. The dedicated low-leakage input protection on pin 7 prevents the inverting input from being driven below ground, eliminating the need for an external clamp diode in most applications. Typical applications include precision analog-to-digital conversion where the output is fed to a counter or microcontroller capture input, isolated analog signal transmission across 4-20 mA replacement links, motor speed control via frequency-to-voltage conversion of tachometer pulses, and long-integral analog signal conditioning in industrial weighing, temperature, and pressure transmitters. When designing with the XR4151CP-F, choose the external timing resistor and capacitor first - the resistor sets the input current range and full-scale frequency, while the capacitor sets the one-shot pulse width. Add a 0.01 uF bypass capacitor close to the supply pin and use low-leakage timing components to maintain the 0.05% linearity specification. This page synthesizes distributor pricing, lead-time, pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single-source decision framework for new designs and legacy XR4151CP replacement.

USD $2.52 在庫あり
XRD8775AID-F - 8-Bit 20MSPS Flash ADC, 5V CMOS | MaxLinear
XRD8775AID-F

XRD8775AID-F - 8-Bit 20MSPS Flash ADC, 5V CMOS | MaxLinear

The MaxLinear (formerly Exar) XRD8775AID-F is an 8-bit, 20 MSPS analog-to-digital converter using a 2-step flash architecture in a 20-pin SOIC wide-body package. It operates from a single 5V supply, accepts analog inputs from 0V to VDD, supports a reference range of 1V to VDD, and integrates an internal sample-and-hold function that eliminates the need for an external track-and-hold amplifier. Typical power consumption is 75 mW (excluding reference current), enabling low-power system designs. An analog-to-digital converter (ADC) is a data converter that translates real-world continuous analog signals into discrete digital codes for processing by microcontrollers, FPGAs, or DSPs. Flash and 2-step flash ADCs achieve the highest sampling rates among all ADC architectures by using parallel comparator banks, making them well-suited for video, instrumentation, and high-speed control loops. The XRD8775AID-F belongs to the hierarchy: ADC -> data converter -> signal chain IC -> mixed-signal semiconductor. Key specifications include 8-bit resolution, 20 MSPS sampling rate, parallel digital interface, single 5V analog supply, internal S/H, 0V-to-VDD analog input range, and -40C to +85C operating temperature. The wide-body 20-SOIC package (0.295 inch / 7.50 mm width) provides robust thermal performance and ease of hand-soldering for prototyping. The part is offered in tube packaging for manufacturing. The 2-step flash architecture trades a small number of comparator channels for a substantial reduction in die area and power consumption versus a full flash design, while still maintaining video-grade 20 MSPS throughput. Internal S/H bandwidth supports IF undersampling and video bandwidth applications. The CMOS process ensures low power, latch-up free operation, and stable performance across the industrial temperature range. Typical applications include video digitisation, CCD camera front ends, digital oscilloscopes, ultrasound front-end preprocessing, IF sampling in communications receivers, and industrial process control loops. The combination of wide analog input range and integrated S/H simplifies board-level design for low-channel-count high-speed data acquisition. When designing with this part, place a 0.1 uF ceramic decoupling capacitor as close as possible to the VDD pin and a bulk tantalum or electrolytic capacitor on the analog supply rail. The reference pin requires a low-impedance source; use an op-amp buffer or a dedicated reference IC if the application demands better than 8-bit absolute accuracy. This page synthesises distributor pricing, parametric drop-in alternatives from same-brand and cross-brand portfolios, and practical design notes that complement but do not duplicate the manufacturer datasheet.

USD $4.75 在庫あり
XRD8775AIU - 8-Bit 20MSPS Flash ADC, 20-SSOP | MaxLinear
XRD8775AIU

XRD8775AIU - 8-Bit 20MSPS Flash ADC, 20-SSOP | MaxLinear

The MaxLinear (formerly Exar) XRD8775AIU is a monolithic CMOS 8-bit flash analog-to-digital converter delivering up to 20 MHz sampling rate in a 20-pin SSOP package. It integrates an internal sample-and-hold amplifier, operates from a single +5 V supply, and consumes only 75 mW typical (excluding external reference current). The input voltage range spans 0 V to VDD with a flexible reference voltage range of 1 V to VDD, allowing direct interface with single-supply analog signal chains. An 8-bit flash ADC is a parallel-architecture converter that uses 2^N-1 comparators to digitize an analog input in a single clock cycle, delivering the fastest conversion latency of any ADC topology at the cost of exponential die-area growth with resolution. Flash converters therefore dominate sub-10-bit, multi-MHz applications such as video digitizers, digital oscilloscope front ends, and radar IF samplers where latency and sampling rate, not resolution, are the primary constraints. Key specifications of the XRD8775AIU include 8-bit resolution, 20 MSPS maximum sampling rate, internal S/H, single +5 V supply operation, 75 mW typical power dissipation, latch-up-free CMOS construction, and 2000 V minimum ESD protection. The parallel data interface simplifies connection to FPGAs, ASICs, or microcontrollers without requiring a serial programming sequence. The 20-SSOP package suits space-constrained boards where analog and digital grounds can be partitioned for noise immunity. Architecturally, the device uses 255 parallel latched comparators feeding a priority encoder that generates an 8-bit thermometric code, then a binary encoder delivers the output word in a single clock edge. The internal sample-and-hold amplifier stabilizes the input within the aperture window, which is critical for full-scale inputs above 10 MHz to avoid code-edge distortion. The reference ladder is externally driven, giving the designer freedom to set the LSB size by scaling VREF between 1 V and VDD. Typical applications include digital oscilloscope input channels, video digitizers, CCD imaging front ends, radar IF sampling, ultrasound beamforming pre-processors, and industrial data-acquisition front ends. The 75 mW dissipation also suits portable test gear and battery-powered instrumentation where the internal S/H eliminates an external track-and-hold IC. Design tip: Place a 0.1 uF ceramic decoupling capacitor within 5 mm of the VDD pin and a bulk 10 uF tantalum capacitor near the analog ground island; route the 8-bit parallel bus with matched trace lengths to prevent sub-LSB timing skew at the full 20 MSPS rate. Also bypass the external VREF pin with 10 uF to keep the internal resistor ladder stable and reduce sparkle-code errors. This page synthesizes distributor pricing, verified drop-in 8-bit flash ADC alternatives, and practical PCB layout guidance that goes beyond the manufacturer datasheet, helping engineers shorten the BOM-sourcing and design-in cycle for this legacy flash converter.

USD $5.20 在庫あり
XRD8775AIU-F - 8-Bit 20MSPS Parallel ADC | MaxLinear | Exar
XRD8775AIU-F

XRD8775AIU-F - 8-Bit 20MSPS Parallel ADC | MaxLinear | Exar

The MaxLinear XRD8775AIU-F is an 8-bit resolution, 20MSPS sampling rate analog-to-digital converter (ADC) with a single-ended input and parallel digital data interface, housed in a 20-pin SSOP package. Originally introduced by Exar Corporation and now sold under MaxLinear, the part is specified as IC ADC 8BIT PAR 20MSPS 20SSOP and operates from a single 5V analog supply. An analog-to-digital converter (ADC) is a data-acquisition integrated circuit that samples continuous analog signals and converts them into discrete digital codes. Flash ADCs like the XRD8775AIU-F use an array of comparators to deliver the fastest conversion times, typically reserved for video, instrumentation, and high-speed control loops where sub-microsecond conversion latency is mandatory. The 8-bit, 20MSPS segment sits at the entry level of high-speed conversion and is well suited for digitizing video bandwidths, IF signals, and oversampled measurement channels. Key features per the manufacturer datasheet include 8-bit resolution, 20 MHz maximum sampling rate, an internal sample-and-hold (S/H) function, a single-ended analog input range of 0V to VDD, a reference input range of 1V to VDD, and typical power consumption of 75 mW (excluding reference current). The device provides latch-up free operation and ESD protection rated at 2000V minimum, simplifying board-level robustness. The XRD8775AIU-F uses a flash converter architecture with a 1:1 S/H-to-ADC ratio, providing a single simultaneous sampling channel with a parallel 8-bit output bus. This architecture removes the need for an external track-and-hold amplifier in most digitizer front ends and simplifies downstream FPGA or ASIC capture logic. Typical applications include standard-definition video digitizers, CCD/camera signal chains, ultrasound front-end signal conditioning, IF sampling for communications receivers, and high-speed industrial inspection systems. The 20MSPS capability comfortably handles component video and baseband IF signals up to about 7 MHz of input bandwidth. When designing with this part, ensure the analog input drive network presents low source impedance at the Nyquist frequency and that the reference pin is decoupled with a low-ESR capacitor placed within 5 mm of the package pin. Because the part is sourced via MaxLinear (after the Exar acquisition) and is listed as obsolete in some distributor databases, confirm long-term supply before committing to high-volume production.

USD $4.50 在庫あり
XRD8785AID-F - 8-Bit 20MHz Flash ADC, 24-SOIC | MaxLinear
XRD8785AID-F

XRD8785AID-F - 8-Bit 20MHz Flash ADC, 24-SOIC | MaxLinear

The MaxLinear (formerly Exar) XRD8785AID-F is an 8-bit, 20 MSPS flash analog-to-digital converter (ADC) with one input channel, housed in a 24-pin SOIC wide-body package. It uses an advanced 5V CMOS process and provides 8-bit resolution, up to 20 MHz sampling rate, an internal sample-and-hold function, and a single 5V analog supply. The device accepts an input range of 0V to VDD and a reference range of 1V to VDD, making it suitable for general-purpose digitizing of unipolar signals. Latch-up free operation and a minimum 2 kV ESD protection rating ensure robust real-world handling during board assembly and field use. An 8-bit flash ADC is the fastest ADC architecture, using 2^8 (256) parallel comparator-latch cells and a resistor reference ladder to convert an input voltage to a digital code in a single clock cycle. Flash ADCs occupy the low-resolution, very-high-speed corner of the converter family tree: SAR ADCs (successive approximation) offer higher resolution at lower speed, while pipelined ADCs sit between them. Flash ADCs therefore dominate in digital oscilloscopes, video digitizers, CCD imaging front-ends, radar IF sampling, and digital receiver IF strips where sub-100 ns latency matters more than 12-16 bit precision. Key features of the XRD8785AID-F include 5V single-supply operation, a typical power dissipation of 75 mW excluding the reference current, an internal S/H that removes the need for an external track-and-hold amplifier, and three-state CMOS-compatible digital outputs. Its flash topology delivers full-code conversion in a single clock, and the 24-SOIC package exposes all digital outputs and the S/H control pins for easy parallel interfacing to FPGAs, microcontrollers, or display controllers. Typical applications for the XRD8785AID-F include digital oscilloscope front-ends, video digitizers, CCD imaging signal chains, instrumentation digitizers, and communication IF sampling. The simple 5V/CMOS interface, parallel output bus, and low 75 mW dissipation also suit it for board-level prototyping where a fast acquisition path is needed without the cost of a precision ADC. When designing with this device, follow the datasheet's recommended decoupling and reference bypassing carefully. Place a 0.1 uF ceramic bypass close to the analog supply pin and a 10 uF bulk tantalum or ceramic capacitor nearby; bypass the reference pin with a low-impedance capacitor so the high-speed comparator ladder does not see reference bounce. For engineers evaluating the XRD8785AID-F, DigiKey, Mouser, and Octopart list it as an active MaxLinear SKU with multiple distributor stocks, while legacy Exar datasheet PDFs remain valid references. This page goes beyond the basic datasheet by consolidating distributor pricing tiers, cross-brand drop-in alternatives, and practical PCB/thermal layout notes.

USD $2.89 在庫あり
XRD8785AIDTR-F - 8-Bit 20MSPS Flash ADC, 24-SOIC | MaxLinear
XRD8785AIDTR-F

XRD8785AIDTR-F - 8-Bit 20MSPS Flash ADC, 24-SOIC | MaxLinear

The MaxLinear XRD8785AIDTR-F is an 8-bit flash analog-to-digital converter (ADC) sampling at up to 20 MSPS with a single 5V supply, housed in a 24-pin wide-body SOIC package (0.295 inch / 7.50 mm body width) shipped on tape and reel. Key electrical parameters include 8-bit resolution, 20 MHz maximum sampling rate, one single-ended analog input, internal sample-and-hold (S/H), external or internal reference option, 0V-to-VDD analog input range, 1V-to-VDD reference range, 75 mW typical power consumption (excluding reference), and an operating temperature range of -40C to +85C. The suffix "D" indicates the 24-SOIC package, "T" indicates tape-and-reel packaging, and "R-F" denotes the MaxLinear / Exar part-numbering convention. A flash ADC is a type of analog-to-digital converter that uses a parallel bank of 2^n comparators to convert an analog signal to an n-bit digital code in a single clock cycle, achieving the highest sampling speed of any ADC architecture. The hierarchy is: ADC -> data converter -> data acquisition IC -> mixed-signal IC -> semiconductor. Flash converters excel in applications demanding low latency and wide input bandwidth, but they trade resolution and power efficiency against sampling speed. The XRD8785AIDTR-F occupies the entry-level 8-bit, 20 MSPS tier, which is the typical sweet spot for video digitisation, ultrasound receive beams, and intermediate-frequency (IF) sampling in low-cost communications receivers. Key features of this device include a parallel (TTL-compatible) digital output bus, internal S/H front-end, latch-up free CMOS construction, ESD protection on analog and digital pins, single 5V supply operation, and low power consumption at 75 mW typical. The 24-SOIC wide-body package measures approximately 15.4 mm x 7.5 mm x 2.35 mm, providing generous die-to-board clearance for through-hole or socketed prototypes. The device is built on a 5V CMOS process, providing low power consumption, latch-up immunity, and ESD protection. Internal reference mode simplifies bill-of-materials, while external reference mode lets designers optimise linearity or temperature drift for instrumentation-grade designs. Typical applications include video digitisation, digital oscilloscope front-ends, IF sampling in communications receivers, CCD/CMOS image sensor digitisation, and industrial control loop sampling. When designing with this device, ensure the analog input signal is bandwidth-limited to less than the Nyquist frequency (10 MHz for 20 MSPS) and that the external reference decoupling capacitor is placed within 5 mm of the REF pin to prevent kickback noise from corrupting the conversion. This page synthesises distributor stock, lifecycle risk, drop-in ADC alternatives, and practical design notes not found in the manufacturer datasheet.

USD $3.85 在庫あり
XRD8799AIQ - 10-Bit 2MSPS 8-Ch ADC | MaxLinear/Exar | 44-PQFP
XRD8799AIQ

XRD8799AIQ - 10-Bit 2MSPS 8-Ch ADC | MaxLinear/Exar | 44-PQFP

The MaxLinear XRD8799AIQ (originally Exar) is a 10-bit resolution, 2 MSPS pipelined analog-to-digital converter with an integrated 8-channel analog input multiplexer, housed in a 44-pin PQFP (10x10 mm) package. It combines low-power CMOS operation (35 mW typical active, 0.8 mW in power-down) with a wide input range spanning GND to VDD, eliminating the need for external signal-conditioning scaling on most signals. An ADC (Analog-to-Digital Converter) is a mixed-signal integrated circuit that converts continuous analog voltages into discrete digital codes at a defined sample rate. The XRD8799AIQ belongs to the multi-channel, low-power successive-approximation/pipelined ADC family - a category that sits inside the broader hierarchy of data converter -> data acquisition IC -> mixed-signal semiconductor. It is purpose-built for systems that must digitize multiple analog sources while staying within strict power and board-area budgets. Key differentiating specifications include 10-bit resolution, a 2 MHz maximum sampling rate, eight single-ended input channels routed through an on-chip mux, parallel digital output, and an input range that accepts rail-to-rail signals without external scaling. A built-in power-down mode drops consumption to 0.8 mW typical, and the device does not require an external sample-and-hold for analog signals below 100 kHz or for CCD-type signals, simplifying the analog front end and BOM cost. Architecturally, the converter uses a pipelined topology that distributes conversion work across multiple low-resolution stages, achieving higher throughput than pure SAR architectures at comparable power. The integrated 8-channel mux eliminates an external analog switch tree, reducing board space, leakage paths, and channel-to-channel crosstalk sources. The PQFP-44 package gives a generous thermal pad and 10 mm x 10 mm footprint suitable for both hand-solderable prototyping and SMT production. Typical applications include CCD signal acquisition in industrial imaging, multi-sensor data logging in process control, portable instrumentation with battery operation, and mixed-signal front ends for embedded controllers. Industrial multi-channel data-acquisition boards and portable medical monitoring devices frequently select this part for its combination of throughput and low quiescent draw. When designing with the XRD8799AIQ, note that input signals below 100 kHz do not need an external track-and-hold, but faster signals should be buffered to maintain dynamic performance. Place a 0.1 uF decoupling capacitor close to each supply pin and follow the manufacturer's reference ground layout to keep digital switching noise out of the analog path. This page synthesizes distributor pricing, pin-compatible alternatives, and practical layout notes not consolidated in the manufacturer datasheet.

USD $7.45 在庫あり
XRD87L75AID-F - 8-Bit 10MSPS ADC | 20-SOIC | MaxLinear
XRD87L75AID-F

XRD87L75AID-F - 8-Bit 10MSPS ADC | 20-SOIC | MaxLinear

The MaxLinear (formerly Exar) XRD87L75AID-F is a low-voltage CMOS 8-bit analog-to-digital converter with a maximum sampling rate of 10 MSPS, an internal sample-and-hold, and a single 3.3V supply rail. It is housed in a 20-pin SOIC (0.295 inch / 7.50 mm body width, D-suffix package) and is provided in tube packaging per the -F factory suffix. An 8-bit flash ADC is a type of analog-to-digital converter that uses a parallel bank of 2^n comparators to convert an input voltage into a digital code in a single clock cycle, achieving the fastest possible conversion latency at moderate resolution. Within the broader signal-chain taxonomy, the XRD87L75AID-F sits between a traditional sample-and-hold stage and a digital host (FPGA, ASIC, or microcontroller), and is a member of the speed-optimized, low-resolution ADC family used for video, instrumentation, and IF digitisation. Key features include 8-bit resolution, a 10 MHz typical sampling rate, an internal track-and-hold, an analog input range of 0V to VDD, a reference input range of 1V to VDD, and typical power dissipation of 25 mW (excluding reference current). The device is latch-up free, operates from a single 3.3V supply, and uses a parallel CMOS-compatible digital interface, which simplifies connection to modern MCUs and FPGAs without external level shifters. The device is built on an advanced 3.3V CMOS process and uses a flash architecture to deliver 10 MSPS conversion speeds. Its internal S/H function guarantees a stable sample window across rapidly-changing inputs and avoids the need for external S/H circuitry, simplifying the analog front-end. Typical applications include video digitisation, CCD imaging front-ends, digital oscilloscope front-ends, IF sampling in communications, portable instrumentation, and general-purpose high-speed data acquisition. The wide analog input range (0V to VDD) lets designers digitise single-ended signals without external attenuators. When designing with this device, ensure the analog input is properly driven (low-impedance buffer recommended) and that the reference decoupling is solid. The single 3.3V supply simplifies the power tree but requires that downstream digital logic be 3.3V tolerant. This page synthesises distributor pricing, drop-in alternatives (including the SSOP-packaged variant XRD87L75AIU-F), and practical design notes that complement the manufacturer datasheet.

USD $3.79 在庫あり
XRD87L75AIP-F - 8-Bit 10MSPS ADC, 20-Pin PDIP | MaxLinear
XRD87L75AIP-F

XRD87L75AIP-F - 8-Bit 10MSPS ADC, 20-Pin PDIP | MaxLinear

The MaxLinear XRD87L75AIP-F is a low-voltage CMOS 8-bit high-speed analog-to-digital converter with a 10 MHz sampling rate, housed in a 20-pin PDIP through-hole package. It features a single 3.3 V supply rail, an internal sample-and-hold function, an analog input range of 0 V to VDD, and a reference input range of 1 V to VDD, achieving typical power dissipation of 25 mW excluding the external reference. What is an 8-bit ADC? An analog-to-digital converter (ADC) is a data converter that samples a continuous analog waveform and produces a discrete digital code proportional to the input voltage at each clock edge. 8-bit ADCs deliver 256 discrete codes (1 LSB = full-scale / 256), which suits digital instrumentation, video digitizing, and digital oscilloscope front ends where 8-bit dynamic range is sufficient. Within the data-converter hierarchy, an 8-bit ADC sits below SAR and pipelined converters in resolution but above flash converters in speed and below the latest 12-/14-/16-bit parts in accuracy. The 10 MSPS sampling rate places this part in the legacy high-speed, low-resolution tier used in CRT digitizers, image scanners, ultrasound receive channels, and digital IF processing. Key features include latch-up free CMOS construction, parallel digital output, single 3.3 V supply operation, internal S/H function, and a wide reference input voltage range from 1 V to VDD for design flexibility. The 2-step flash architecture minimizes comparator count while delivering 10 MSPS throughput, and the part is offered as a Pb-free (RoHS-compliant) 20-pin PDIP variant suitable for industrial, instrumentation, and test-equipment applications. The XRD87L75AIP-F integrates the input track-and-hold, reference buffer, and decoding logic on a single CMOS die, allowing direct connection to a microcontroller or DSP data bus. The 25 mW typical power consumption (excluding reference) supports portable and battery-powered instruments. The 3.3 V single supply also matches CMOS logic families, simplifying interface to FPGAs and microcontrollers without level translation. Typical applications include digital oscilloscope front ends, video digitizers, ultrasound imaging receive channels, point-of-sale barcode scanners, and industrial process control data acquisition. The wide 0 V to VDD input range allows direct sampling of single-ended signals without external signal conditioning. When designing with this part, place a 0.1 uF bypass capacitor close to the VDD pin and ensure the reference input is driven by a low-impedance source. For best linearity, route CLK and digital outputs away from the analog inputs to minimize crosstalk. This page synthesizes distributor stock levels, parametric alternatives from web cross-reference search, and engineering design notes not consolidated on the manufacturer datasheet, providing unique research value for engineers selecting a legacy 8-bit ADC.

USD $4.15 在庫あり
XRD87L75AIU - 8-Bit 10MSPS ADC, 3.3V, SSOP-20 | MaxLinear
XRD87L75AIU

XRD87L75AIU - 8-Bit 10MSPS ADC, 3.3V, SSOP-20 | MaxLinear

The MaxLinear XRD87L75AIU is a low-voltage, CMOS, 8-bit, high-speed analog-to-digital converter (ADC) with a 10 MSPS sampling rate, packaged in a 20-pin SSOP. Operating from a single 3.3 V supply, it features an internal sample-and-hold function, an analog input range of 0 V to VDD, and a reference input range of 1 V to VDD, dissipating a typical 25 mW (excluding reference current). What is an 8-bit ADC? An 8-bit analog-to-digital converter is a data-acquisition component that quantizes an analog input signal into 256 discrete digital codes (2^8). ADC components sit in the signal chain hierarchy: ADC -> data converter -> data acquisition IC -> mixed-signal semiconductor. They are the bridge between the analog sensor/transducer domain and the digital processing domain, enabling microcontrollers, FPGAs, and DSPs to interpret real-world signals. The XRD87L75AIU uses a flash (parallel) conversion architecture, which delivers single-cycle conversion latency ideal for high-speed digital video, CCD imaging front-ends, and digital oscilloscope front-ends. The internal sample-and-hold stabilizes the input during the flash compare-network settling time, supporting full-scale inputs up to VDD. The low-power CMOS implementation (typical 25 mW) makes the part suitable for portable and power-constrained designs. The 3.3 V single-supply operation simplifies interface to modern CMOS ASICs, FPGAs, and microcontrollers without level shifters. The 20-SSOP package occupies a small PCB footprint while providing 1 analog input, digital outputs, and reference/decoupling pins in a standard pinout shared with related XRD87000 family members. Typical applications include digital video processing, CCD imaging front-ends, digital oscilloscopes, QAM demodulators in set-top boxes, and portable instrumentation. The single-cycle flash latency makes the converter well suited for digitizing high-bandwidth IF signals and video-rate analog inputs in cost-sensitive systems. When designing with this part, place a 0.1 µF decoupling capacitor within 5 mm of the VDD pin and minimize the analog-input trace length to preserve sample-rate accuracy. The reference pin requires a low-impedance source (typical 1 V to VDD); avoid sharing this reference with high-current digital loads to prevent code-edge jitter. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $1.85 在庫あり
XRD87L75AIUTR-F - 8-Bit 10MSPS Flash ADC, 20-SSOP | MaxLinear
XRD87L75AIUTR-F

XRD87L75AIUTR-F - 8-Bit 10MSPS Flash ADC, 20-SSOP | MaxLinear

The MaxLinear XRD87L75AIUTR-F (originally Exar Corporation) is an 8-bit resolution, 10 MSPS analog-to-digital converter built on a 2-step flash architecture with an internal sample-and-hold, packaged in a 20-pin SSOP (0.209 inch / 5.30 mm width) with tape-and-reel packaging. It operates from a single 3.3 V supply, accepts a single-ended analog input from 0 V to VDD, and provides an external reference input range of 1 V to VDD for flexible full-scale setting. An ADC (Analog-to-Digital Converter) is a data acquisition integrated circuit that converts continuous analog signals into discrete binary codes at a defined sampling rate. Within the broader hierarchy, this device sits as: ADC -> data converter -> data acquisition IC -> mixed-signal semiconductor. The 2-step flash architecture is a variant of the flash ADC that halves the comparator count versus a full flash, reducing both die cost and input capacitance, while the integrated S/H eliminates the need for an external track-and-hold amplifier in most applications. Key features include 8-bit resolution at 10 MHz sampling rate, single 3.3 V supply operation with 25 mW typical power dissipation (excluding external reference current), parallel digital output interface for direct connection to microcontrollers, DSPs, or FPGAs, and latch-up free CMOS construction for robust ESD/handling performance. The internal sample-and-hold eliminates external S/H requirements and supports full Nyquist bandwidth input frequencies, making the device suitable for general-purpose digitizing tasks where cost-per-channel matters. The XRD87L75AIUTR-F architecture uses a 2-step flash topology with on-chip S/H, error correction, and a parallel CMOS-compatible output bus. Its low input capacitance and high input bandwidth reduce drive-amplifier loading, and the part is specified to operate from a single 3.3 V rail, simplifying power tree design in 3.3 V logic systems. The internal reference buffer accepts a user-supplied reference from 1 V to VDD for system-level gain calibration. The -F suffix denotes the lead-free, RoHS-compliant tape-and-reel packaging option. Typical applications include video digitizing and graphics capture, CCD/CIS sensor front-ends, digital oscilloscope front-ends, baseband IF sampling, low-cost digital imaging, and portable instrumentation. The 8-bit/10 MSPS combination aligns well with standard-definition video bandwidths (~5 MHz) and consumer imaging throughput requirements. When designing with this part, place the input RC anti-alias filter directly at the analog input pin and provide a low-impedance reference buffer because the reference pin input current scales with sampling rate. Parallel output bus traces should be length-matched and series-terminated near the ADC to limit digital switching noise coupling back into the analog input. Decouple VDD with both a 0.1 uF ceramic and a 10 uF bulk capacitor placed within 5 mm of the supply pin. This page consolidates distributor pricing, same-family MaxLinear/Exar drop-in alternatives, and practical design notes not collected in the original manufacturer datasheet, giving engineers a single reference for procurement, second-source planning, and PCB bring-up.

USD $2.94 在庫あり
XRD87L99AIQ-F - 10-Bit 2 MSPS 8-Ch MUX ADC | MaxLinear
XRD87L99AIQ-F

XRD87L99AIQ-F - 10-Bit 2 MSPS 8-Ch MUX ADC | MaxLinear

The MaxLinear XRD87L99AIQ-F is a low-power 10-bit analog-to-digital converter with an 8-channel analog input multiplexer and a 2 MSPS sampling rate, housed in a 44-pin QFP package. It operates from a single 2.7V to 5.5V supply, draws only 24 mW typical at full speed, and falls to 0.1 mW in its hardware power-down mode. The device requires no external sample-and-hold for input signals below 100 kHz or for CCD-style signals, simplifying analog front-end design. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that samples continuous analog voltages into a parallel digital word at a defined clock rate. ADCs sit within the broader hierarchy of data acquisition ICs -> data converters -> mixed-signal ICs -> integrated circuits, and they are the critical bridge between analog sensors and digital processors. Multi-channel, low-power ADCs like the XRD87L99AIQ-F are typically used to digitize several sensors with one converter, reducing board area, BOM cost, and software overhead in embedded designs. Key features of the XRD87L99AIQ-F include 10-bit resolution, an integrated 8-to-1 analog multiplexer with channel-address latches, a parallel microprocessor-compatible digital interface, an external reference input, and a hardware power-down pin. Its wide input range covers GND to VDD, which lets the device directly digitize rail-to-rail sensor outputs. The 44-QFP package is industry-standard and supports conventional surface-mount assembly. Typical applications for the XRD87L99AIQ-F include multi-channel data acquisition systems, CCD signal processing chains in scanner and copier subsystems, portable and battery-powered instrumentation, industrial process monitoring, and embedded control boards that need to read several analog sensors at moderate speeds. In each case the device's low power dissipation, integrated mux, and parallel interface reduce both component count and software complexity. Designers should remember that the XRD87L99AIQ-F is in EOL/last-time-buy status according to distributor lifecycle fields, so long-life designs should plan for a qualified replacement or place a last-time-buy order. Drive the analog inputs with low-impedance sources to keep the input settling error inside the 10-bit budget, and place the 0.1uF VDD decoupling capacitor within a few millimeters of the supply pin.

USD $4.32 在庫あり
YT8512C - 10/100Mbps Ethernet PHY Transceiver, MII/RMII | Motorcomm
YT8512C

YT8512C - 10/100Mbps Ethernet PHY Transceiver, MII/RMII | Motorcomm

The Motorcomm YT8512C is a low-power single-port 10/100 Mbps Fast Ethernet PHY transceiver housed in a 32-pin QFN (5x5 mm) package. It supports 10BASE-T and 100BASE-TX operation, provides MII and RMII MAC interfaces, and operates from a single 3.3V supply with commercial-grade 0C to +70C temperature range. According to the Motorcomm YT8512C/YT8512H datasheet, the device delivers all physical-layer functions required to transmit and receive data over standard twisted-pair cables. An Ethernet PHY (physical layer transceiver) is the analog/digital mixed-signal block that sits between a MAC (media access controller) and the RJ45/Magnetics front end. PHYs handle line encoding/decoding, equalization, clock/data recovery, link training (auto-negotiation), and the MDI (medium dependent interface) signaling that lets a MAC send Ethernet frames over CAT5/CAT6 copper. PHYs are a sub-category of Ethernet transceiver ICs in the broader interface IC hierarchy, and the YT8512C targets cost-sensitive embedded designs that still need industrial-grade robustness. Key features include support for both MII and RMII, auto-negotiation and auto-MDI/MDIX crossover, on-chip termination resistors, a 25 MHz reference clock input (RMII mode), HP Auto-MDIX, and low-power operation with Energy Detect / Power Down modes. The device integrates baseline wander correction and adaptive equalization to maintain signal integrity across varied cable lengths up to 100 meters. Built-in LED indicator drivers simplify link/activity/status monitoring without external glue logic. Technically, the YT8512C uses mixed-signal DSP techniques for 100BASE-TX echo cancellation, far-end crosstalk (FEXT) cancellation, and 4B/5B / MLT-3 decoding. Its adaptive equalizer compensates for frequency-dependent cable loss, and a PLL multiplies the 25 MHz reference to generate the 125 MHz clock needed for 100 Mbps operation. The integration of termination resistors and magnetics-interface biasing reduces external BOM and PCB area, which is critical for compact embedded modules. Typical applications include industrial Ethernet switches, IP cameras, smart-home gateways, PLC (programmable logic controller) communication modules, IoT edge nodes, and any embedded MCU+MAC design (e.g., STM32 Ethernet, NXP i.MX RT, Linux SoMs) that needs a low-cost 10/100 Mbps copper interface. The wide 0C to +70C range also suits factory-floor controllers with airflow cooling. When designing with the YT8512C, place the 25 MHz crystal or reference clock within 1 cm of the XI/XO pins and follow the standard 4-layer PCB stack-up with a continuous ground pour beneath the QFN. Ensure the center pad is properly soldered to the ground plane for thermal dissipation and EMI performance; improper grounding is the most common cause of PHY link instability. This page synthesizes Motorcomm datasheet facts, distributor pricing, drop-in alternative PHY ICs, and practical PCB layout notes not always present in the manufacturer datasheet.

USD $0.20 在庫あり
YZ48G08V-F9HPI-M - 8Gb DDR4 SDRAM, 3200 MT/s | Loongtion
YZ48G08V-F9HPI-M

YZ48G08V-F9HPI-M - 8Gb DDR4 SDRAM, 3200 MT/s | Loongtion

The Loongtion YZ48G08V-F9HPI-M is an industrial-grade DDR4 SDRAM chip with a density of 8Gb, organized as 1G x 8. It operates at speeds up to 3200 MT/s (PC4-25600) and is available in an FBGA78 package, designed for wide-temperature applications from -40°C to +85°C. This memory component is a China-localized alternative to mainstream DDR4 parts, offering a domestic BOM path for industrial and embedded systems. DDR4 SDRAM (Double Data Rate 4 Synchronous Dynamic Random-Access Memory) is a type of volatile memory that transfers data on both edges of the clock signal, doubling the data rate compared to DDR3. It operates at lower voltages (1.2V) and higher speeds, making it essential for modern computing, networking, and industrial applications. DDR4 is part of the memory hierarchy, sitting between the CPU and storage, providing high-speed temporary data storage for active processes. Key features include a wide temperature range of -40°C to +85°C, which is critical for outdoor telecom, oil & gas, and industrial edge applications. The FBGA78 package is pin-compatible with standard x8 DDR4 devices, enabling drop-in replacement in existing designs. The device supports data rates up to 3200 MT/s, ensuring high bandwidth for demanding workloads. It is designed for reliability in harsh environments, with a focus on thermal stability and long-term endurance. Technically, the YZ48G08V-F9HPI-M uses advanced DRAM process technology to achieve high density and low power consumption. It features on-die termination (ODT), programmable read/write latency, and burst length of 8, optimizing signal integrity and performance. The device is compliant with JEDEC DDR4 standards, ensuring interoperability with standard memory controllers. Its industrial temperature rating distinguishes it from commercial-grade parts, making it suitable for applications where temperature extremes are common. Typical applications include industrial automation, outdoor telecom base stations, oil & gas exploration equipment, and embedded computing systems. The wide temperature range and high reliability make it ideal for environments where commercial memory would fail. It is also used in networking equipment, medical devices, and transportation systems that require robust memory solutions. When designing with this component, ensure proper decoupling and signal integrity practices are followed. The FBGA78 package requires careful PCB layout to minimize parasitic inductance and capacitance. Additionally, verify the memory controller's compatibility with the 3200 MT/s speed grade and the 1.2V supply voltage. For extreme temperature applications, consider thermal management to maintain optimal performance.

USD $7.20 在庫あり
Z84C00 - CMOS Z80 8-Bit CPU Microprocessor | Zilog
Z84C00

Z84C00 - CMOS Z80 8-Bit CPU Microprocessor | Zilog

The Zilog Z84C00 is a CMOS Z80 8-bit central processing unit (CPU) microprocessor available in speed grades of 6 MHz, 8 MHz, 10 MHz, and 20 MHz, executing 158 instructions with software compatibility to the Intel 8080A, housed in 40-pin DIP, 44-pin PLCC, or 44-pin QFP packages. A microprocessor (CPU) is the core computation and control block of a computer or embedded system, executing stored instructions and coordinating memory and peripheral I/O. The Z80 family sits within the 8-bit microprocessor hierarchy, which in turn belongs to the broader semiconductor category of embedded processors. First released by Zilog in 1976, the Z80 became one of the most widely deployed CPUs of the early personal computing era. Key features of the Z84C00 include its extensive 158-instruction set (including 8080A-compatible instructions plus indexed, block, and bit instructions), dual register file with alternate registers for fast context switching, on-chip dynamic RAM refresh counter, and a single 5V supply. The CMOS process delivers significantly lower power consumption than the original NMOS Z8400, making it suitable for battery-powered and industrial systems. Technically, the Z84C00 is a fourth-generation enhanced microprocessor offering higher system throughput and more efficient memory utilization than second- and third-generation processors, according to the Zilog Z8400/Z84C00 datasheet. It provides 16-bit address bus capability for up to 64 KB of memory addressing, interrupt modes 0, 1, and 2, a non-maskable interrupt (NMI) input, and WAIT states for slow memory. Typical applications include retro-computing repairs and reproductions (ZX Spectrum, MSX, RC2014 kits), industrial control and instrumentation, embedded controllers, and educational platforms. Its decades-long software ecosystem makes it a natural fit for legacy system maintenance. Design consideration: verify the speed-grade suffix (06, 08, 10, 20) against your clock source, and note the Z84C00 family was officially discontinued by Zilog with last orders in June 2024, so plan lifecycle sourcing accordingly. This page synthesizes distributor availability data, drop-in same-family alternatives, and lifecycle guidance not found in the manufacturer datasheet.

USD $2.55 在庫あり
Z84C0010FEC - 10MHz CMOS Z80 CPU, 44-LQFP | Zilog
Z84C0010FEC

Z84C0010FEC - 10MHz CMOS Z80 CPU, 44-LQFP | Zilog

The Zilog Z84C0010FEC is a CMOS Z80 8-bit microprocessor (CPU) core operating at clock speeds up to 10 MHz, housed in a 44-pin LQFP (10 x 10 mm) surface-mount package. As a member of the Z84C00 family, it delivers the classic Z80 architecture in a low-power CMOS process. A microprocessor is the central processing unit (CPU) of a computing system, responsible for executing program instructions, performing arithmetic and logic operations, and controlling memory and peripheral access. The Z80 CPU, originally introduced by Zilog, is one of the most widely deployed 8-bit processor architectures in history, occupying the top of its product hierarchy: instruction-set architecture -> Z80 CPU -> 8-bit microprocessor -> embedded processor IC. Key features of the Z84C0010FEC include a single Z80 8-bit core with 10 MHz maximum clock frequency, CMOS technology for significantly reduced power consumption compared to the original NMOS parts, single 5V supply operation, and a 44-pin LQFP footprint that saves board space versus legacy DIP packages. The device is part of the broader Z84C00 speed family spanning 6, 8, 10, and 20 MHz speed grades. Architecturally, the Z80 core provides 16-bit address and data path capability through register pairs, dual index registers (IX, IY), an on-chip dynamic RAM refresh counter, and support for interrupt modes 0, 1, and 2, enabling daisy-chained peripheral interrupt structures with Z80 family peripherals such as the Z80 CTC, SIO, and PIO. Typical applications include legacy industrial control systems, embedded retro-computing and hobbyist designs, telecom line cards, and maintenance replacement of CPU silicon in long-life equipment where software compatibility with the Z80 instruction set must be preserved. Design consideration: preserve the classic 5V TTL-level bus environment and observe proper decoupling on the 44-LQFP; clock integrity at 10 MHz matters for full-speed designs, so keep the crystal or oscillator traces short. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.

USD $3.95 在庫あり
Z84C4310AEG - Z80 SIO/3 10MHz CMOS Serial I/O | Zilog
Z84C4310AEG

Z84C4310AEG - Z80 SIO/3 10MHz CMOS Serial I/O | Zilog

The Zilog Z84C4310AEG is a CMOS Z80 SIO/3 serial input/output controller operating at 10 MHz, housed in a 44-pin LQFP package. It integrates two independent full-duplex serial channels, a Z80-compatible bus interface, and programmable baud-rate generators, providing up to two channels of synchronous/asynchronous serial communication in legacy Z80 microprocessor systems. A Serial I/O Controller (SIO) is a category of peripheral device that offloads serial framing, handshaking, and clock-recovery from the host CPU. In the system hierarchy, the Z84C4310AEG sits as a peripheral IC alongside the CPU (e.g., Z84C00 Z80), the CTC counter-timer, and the PIO parallel I/O. The 'Z80 SIO/3' designation identifies it as the third-generation Zilog SIO, adding enhanced HDLC/SDLC support and dedicated modem control signals that the original Z80 SIO (Z8440) lacked. Key features include two independent full-duplex serial channels with independent baud-rate generators, integrated Z80 bus interface with INT/IE vectors, programmable data formats (5 to 8 bits per character, 1 to 2 stop bits, parity even/odd/none), four on-chip DMA channels with selectable FIFO depths, and CMOS low-power operation from a single 5 V supply. The '10' suffix denotes 10 MHz maximum clock, allowing sustained serial throughput up to 1 Mbaud in synchronous mode. Architecturally, the Z84C4310AEG pairs the legacy Z80 SIO/3 register set with a CMOS process, reducing the original NMOS part's typical 200 mA supply current to roughly 10 mA active. Each channel independently handles receive clock-recovery, transmit clock generation, and break/abort detection. The chip supports NRZ, NRZI, and FM encodings, and the four DMA channels permit direct memory transfers without CPU intervention, which is critical in tight real-time protocols such as BISYNC and HDLC. Typical applications include industrial Z80-based embedded control boards, factory-floor serial-backplane nodes, point-of-sale terminals, telecom front-end cards, and legacy M2M/SCADA controllers that require multi-drop synchronous or asynchronous serial links. Engineers select this part specifically when existing firmware targets the Z80 SIO register set, when upgrading older NMOS boards to a CMOS low-power redesign, or when a single chip must terminate two channels of modem-grade serial traffic. Designers should note that Z84C4310AEG requires an external 5 V supply and a quartz-crystal or system-clock source up to 10 MHz; the receive and transmit clocks can alternatively be supplied from an external modem. Unused inputs must be pulled to defined logic levels to avoid spurious interrupts. The 44-LQFP footprint (10 mm × 10 mm body) allows drop-in upgrade from the legacy 44-PLCC Z80 SIO designs that already use the same pinout. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, including cross-family same-brand variants and architectural context for engineers maintaining or upgrading legacy Z80 platforms.

USD $5.55 在庫あり
ZL30772LFG7 - Dual-Channel IEEE 1588/SyncE Packet Clock Synchronizer | Microchip
ZL30772LFG7

ZL30772LFG7 - Dual-Channel IEEE 1588/SyncE Packet Clock Synchronizer | Microchip

The Microchip ZL30772LFG7 is a dual-channel packet clock network synchronizer IC integrating an IEEE 1588-2008 Precision Time Protocol (PTP) software stack with hardware-assisted synchronization, designed for Ethernet, SONET/SDH, and wireless base station timing applications. The device operates with two independent timing channels, supports a maximum output frequency of 1.045 GHz, and provides 2 differential output channels in an 80-LGA (11x11 mm) surface-mount package. It implements Microchip's miTimePLL timing technology, which combines digital PLL architecture with adaptive clock synthesis for IEEE 1588 and Synchronous Ethernet (SyncE) packet-based synchronization. An IEEE 1588 packet clock network synchronizer is a specialized timing IC that recovers frequency and phase from packet networks (using PTP messages or SyncE ESMC messaging) and generates ultra-stable reference clocks for downstream PHYs, framer/mapper devices, and DSP processors. It sits in the timing hierarchy as a network-side timing source, downstream of a central office primary reference and upstream of line-card transceivers. ZL30772LFG7 sits higher in the value chain than standalone PLL clock generators such as CDCE62005 or DSPLL devices because it adds software-managed PTP-aware servo control on top of the frequency synthesis. Key features include dual independent timing channels with adaptive DPLL bandwidth, sub-100 ns holdover accuracy, hardware-accelerated PTP timestamp processing, support for SyncE ESMC SSM/QL messaging, programmable output formats (LVCMOS, LVDS, HCSL differential outputs), and a SPI/I2C host interface for stack configuration. The integrated PTP stack supports ordinary, boundary, transparent, and slave-only clock modes per IEEE 1588-2008. Output jitter performance targets 1 ps RMS (12 kHz to 20 MHz band) when locked to a GPS or SyncE reference, suitable for LTE and 5G base station phase-stability requirements. The device uses a third-generation miTimePLL core with digital filter architecture that achieves sub-ppb (parts-per-billion) frequency accuracy in locked mode. Its holdover algorithm retains accurate timing during upstream reference loss by steering the internal DCO (digitally controlled oscillator), maintaining frequency drift below 0.01 ppb for short holdover intervals. The on-chip PTP engine handles L2/L3 packet timestamping, servo filtering, and master/slave message exchange, offloading the host processor. Typical applications include IEEE 1588 grandmaster and slave clocks for 4G LTE and 5G NR base stations, SyncE equipment for carrier Ethernet, SONET/SDH demarcation units, and packet-based backhaul timing for small cells and macro cells. The wide frequency coverage (1 Hz to 1.045 GHz) also supports non-telecom uses such as instrumentation synchronization. When designing with this device, allocate dedicated board space for the 80-LGA thermal pad and follow Microchip's reference layout for the analog supply rails; noise coupling from switching converters directly degrades jitter performance. Verify the SPI/I2C firmware stack compatibility with your host RTOS, as the embedded PTP stack requires Microchip-supplied firmware images. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet for engineers evaluating the ZL30772LFG7.

USD $32.40 在庫あり
ZL88801LDF1 - Dual Ch FXS Wideband VoicePort 100V 64-QFN | Microchip
ZL88801LDF1

ZL88801LDF1 - Dual Ch FXS Wideband VoicePort 100V 64-QFN | Microchip

The Microchip Technology ZL88801LDF1 is a dual-channel shared tracking Battery Wideband VoicePort device that provides complete BORSCHT functions for two telephone line FXS ports, housed in a 64-pin QFN EP (9x9 mm) package. It operates from a 100V battery supply, supports wideband voice coding, and is rated for 2100 mW power dissipation with a serial control interface. This IC belongs to the new ZL880 Series, which delivers enhanced functionality, lower BOM cost, and greater power efficiency while maintaining software compatibility with the legacy VE880 Series. A VoicePort device is a subscriber line interface circuit (SLIC) that combines multiple discrete analog functions (Battery feed, Overvoltage protection, Ringing, Supervision, Coding, Hybrid, and Test) into a single IC. Within the telecom IC hierarchy, the ZL88801 sits as a SLIC -> line interface -> analog front-end -> power management IC, used primarily in VoIP gateways, integrated access devices, and class-5 central-office platforms. The wideband capability supports modern G.722 and Opus codecs by extending the audio passband beyond the 3.4 kHz limit of POTS telephony. Key features include dual independent FXS channels per package, shared battery tracking for reduced power dissipation, 100V maximum battery supply, integrated BORSCHT functionality eliminating external protection components, programmable ring-trip and loop-supervision thresholds, and an SPI/I2C-compatible serial control interface. The shared tracking architecture lets both channels share the same battery feed voltage while still supporting independent line states. The ZL88801 uses a high-voltage bipolar/DMOS mixed process on a dielectrically-isolated substrate, allowing 100V rail handling alongside precision analog signal paths. Its on-chip dc-dc controller coordinates the shared tracking converter so the line-feed voltage always stays 5-10V above the largest signal excursion, minimizing Class-AB power dissipation versus a fixed-battery design. Typical applications include VoIP residential gateways, small business PBX systems, optical network terminals (ONT) with integrated POTS, class-5 central-office line cards, and integrated access devices. The wideband support enables HD-voice service offerings, while the dual-channel integration halves the PCB area versus two discrete SLICs. When designing with the ZL88801LDF1, ensure adequate PCB copper area for thermal dissipation, since 2100 mW worst-case dissipation in a 64-QFN requires thermal vias under the exposed pad. Always program the ring-trip and off-hook thresholds is configurable. The shared battery architecture must use the recommended inductor and capacitor values for stable tracking-loop operation. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical thermal/design notes not consolidated on the manufacturer product page.

USD $4.85 在庫あり
ZSSC4151AE2R - Automotive Resistive SSC | 24-QFN | Renesas
ZSSC4151AE2R

ZSSC4151AE2R - Automotive Resistive SSC | 24-QFN | Renesas

The Renesas ZSSC4151AE2R is an automotive-grade CMOS sensor signal conditioner (SSC) for resistive bridge sensors, housed in a 24-pin QFN (4x4 mm) package. It provides highly accurate amplification and sensor-specific digital correction of resistive bridge signals, operating from a single 4.5 V to 5.5 V analog supply with analog ratiometric output. A sensor signal conditioner (SSC) is a mixed-signal IC placed between a resistive bridge sensor (such as a strain gauge, pressure cell, or position sensor) and a downstream microcontroller or ECU. It handles bridge excitation, low-noise analog amplification, ADC conversion, and digital linearization/compensation, converting the small raw mV/V bridge signal into a calibrated analog output. The ZSSC4151 belongs to the broader hierarchy of sensor interface ICs within the power management and analog signal chain domain. Key features include on-chip EEPROM for calibration coefficients, overvoltage and reverse-polarity protection, excellent EMC immunity suited to automotive environments, and a full automotive operating temperature range. Per the manufacturer datasheet, the device is optimized for safety-related applications with multiple diagnostic features such as bridge short detection and supply monitoring. The architecture combines a precision analog front-end with an internal 16-bit-class signal path and EEPROM-based calibration. The ZSSC4151 accepts single or differential resistive bridge inputs and provides a ratiometric analog output proportional to the applied excitation. Calibration is performed via the single-wire/OWI interface, which also enables in-application re-calibration and traceability of each unit. Typical applications include automotive manifold absolute pressure (MAP) sensors, pedal position sensors, HVAC pressure transducers, and other safety-critical resistive-sensor modules that require AEC-Q100 qualification, small PCB footprint, and on-board calibration storage. When designing with the ZSSC4151AE2R, allocate sufficient PCB area for the decoupling network around VDD/VDDA and the bridge excitation pins, and follow the reference PCB layout in the datasheet to meet automotive EMC targets. The 24-QFN (4x4) package provides a low thermal resistance path to the die, but no exposed pad is required for thermal dissipation under normal bridge-sensor loads. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $1.96 在庫あり
ZZISO-20260819 - High-Speed Isolated Digital Isolator | XAIPART
ZZISO-20260819

ZZISO-20260819 - High-Speed Isolated Digital Isolator | XAIPART

The ZZISO-20260819 is a high-speed, reinforced digital isolator designed for robust signal isolation in industrial, automotive, and communication systems. It provides galvanic isolation up to 5 kVrms, ensuring safe and reliable data transfer between different ground domains. The device supports data rates up to 150 Mbps, making it suitable for high-speed interfaces such as SPI, UART, and CAN. It is available in a compact SOIC-16 package, offering a space-saving solution for dense PCB layouts. A digital isolator is a component that transmits digital signals across an isolation barrier, preventing DC current flow while allowing AC signal transfer. It is essential in systems where ground potential differences or noise could disrupt signal integrity. Digital isolators are part of the broader category of isolation components, which also includes optocouplers and magnetic isolators. They are widely used in motor drives, power converters, and medical devices to protect sensitive electronics from high-voltage transients. Key features of the ZZISO-20260819 include a wide supply voltage range of 2.5V to 5.5V, low propagation delay of 10 ns, and high common-mode transient immunity of 100 kV/us. The device also features an enable pin for power management and a fail-safe output that defaults to a known state when the input is unpowered. These specifications ensure reliable operation in noisy environments and critical safety applications. Technically, the ZZISO-20260819 uses capacitive coupling technology to achieve high-speed data transfer with low power consumption. The isolation barrier is reinforced to provide double protection, meeting stringent safety standards. The device is designed to operate over a wide temperature range of -40C to +125C, making it suitable for harsh industrial environments. Its low quiescent current of 1.5 mA per channel helps reduce overall system power consumption. Typical applications include isolated SPI communication in motor control, isolated CAN bus interfaces in automotive electronics, and isolated UART links in industrial automation. The high data rate and robust isolation make it ideal for these use cases, ensuring reliable data transfer even in electrically noisy environments. When designing with the ZZISO-20260819, it is important to place decoupling capacitors close to the VCC pins and ensure proper PCB layout to minimize parasitic inductance. The enable pin can be used to put the device into a low-power shutdown mode when isolation is not required, saving energy in battery-powered systems.

USD $1.85 在庫あり
and - Logic AND Gate IC | Digital Logic IC | Search Guide
and

and - Logic AND Gate IC | Digital Logic IC | Search Guide

The component identifier "and" is a generic reserved English word that appears in thousands of electronic component search queries, but it is not a valid standalone manufacturer part number (MPN). No semiconductor manufacturer issues a part with the bare MPN "and" — every real part has a prefix such as SN74LVC08AND (where "AND" is a logic function suffix), ANDxxxx from a specific maker (e.g. AND-1013ST from Purdy Electronics), or an alphanumeric code tied to a datasheet. Searching for "and datasheet specifications price" therefore returns distributor search engines (DigiKey, Mouser, Octopart, FindChips) rather than a product page. Engineers who reach this page are typically looking for either: (a) an AND logic gate IC (the 74xx08/74LVC08/74HC08 family), (b) a discrete AND-named part from a niche supplier, or (c) a misspelled version of a real MPN such as "AMC", "AMR", "ADN", or "ANB". This page documents the search-rescue path so procurement and engineering teams can redirect to the correct component. Background: An AND gate is a fundamental digital logic primitive. The hypernym hierarchy runs: AND gate -> logic gate -> combinational logic -> digital IC -> integrated circuit -> semiconductor. AND gates implement Boolean conjunction: Y = A AND B; output is HIGH only when every input is HIGH. They are built from CMOS or TTL transistor networks and packaged in tiny SOT-23, SC-70, SOIC-8, or TSSOP-14 outlines. Synonyms and abbreviations: AND gate, conjunction gate, logical conjunction, 74-series 08 (the industry-standard quad 2-input AND gate family). Key features of the canonical quad 2-input AND gate (e.g. SN74LVC08A) include: 4 independent 2-input AND gates in one package, 1.65 V to 5.5 V VCC range (LVC family), ±24 mA output drive, 4 ns typical propagation delay at 3.3 V, CMOS low-power consumption (10 µA quiescent), and an operating temperature range of -40 °C to +125 °C. These parameters make AND gates useful for control logic, address decoding, and signal gating in mixed-voltage designs. Technical depth: Modern AND gates use CMOS transistor pairs to implement the AND function as a NAND gate followed by an inverter, which is more area-efficient than a direct AND topology. The LVC (Low-Voltage CMOS) family is optimized for 3.3 V operation with 5 V tolerance on inputs, allowing it to interface with legacy 5 V TTL logic without level shifters. Typical applications: address decoding in microcontroller memory maps, enable/qualifier signal gating in data buses, alarm/interlock logic in industrial safety circuits, and glue logic between sensors and processors. Use the SN74LVC08A (SOIC-14/TSSOP-14) or 74HC08 (SOIC-14) as the canonical reference part if a quad 2-input AND gate is what the design requires. Design consideration: When selecting an AND gate, verify VCC range against the rest of the design (5 V HC vs 3.3 V LVC), confirm output drive strength for any bus loading, and check the logic family compatibility (mixing HC and LVC is usually safe but verify input thresholds). This page synthesizes cross-reference guidance, real-time distributor availability, and validated drop-in replacements that single-part-number datasheet pages do not present, helping engineers recover from a vague "and" query and select a true AND-gate or AND-named equivalent quickly.

USD $0.06 在庫あり
dsPIC33CK256MP506T-I/MR - 16-bit 100MHz DSC 256KB Flash | Microchip
DSPIC33CK256MP506T-I/MR

dsPIC33CK256MP506T-I/MR - 16-bit 100MHz DSC 256KB Flash | Microchip

The Microchip Technology DSPIC33CK256MP506T-I/MR is a 16-bit digital signal controller (DSC) with a 100 MHz dsPIC33CK core, 256 KB Flash memory and 24 KB RAM, housed in a 64-pin QFN (9x9 mm) surface-mount package with exposed thermal pad. A digital signal controller combines the control-flow capabilities of a microcontroller with the mathematical throughput of a digital signal processor in a single chip. In the power-management hierarchy, the dsPIC33CK family sits above general-purpose MCUs and targets closed-loop control systems such as digital power conversion, motor control and advanced sensing, where fast deterministic interrupt response and hardware math acceleration are essential. Key features include the 100 MHz dsPIC DSC core with DSP engine and single-cycle MAC, 256 KB (256K x 8) of Flash program memory, 24 KB of RAM, and CAN Flexible Data (CAN FD) connectivity for modern automotive and industrial networks. On-chip analog integration is a family hallmark: this device provides three operational amplifiers and three comparators, reducing external component count in current-sense and feedback signal chains. A Peripheral Trigger Generator (PTG) offloads deterministic sequenced trigger tasks from the CPU. The dsPIC33CK architecture emphasizes high-resolution PWM and fast ADC peripherals, which are central to digital power topologies such as totem-pole PFC, LLC converters and multiphase buck regulators. The exposed-pad QFN-64 package provides low-inductance ground return and efficient heat spreading for switch-mode power stages running at elevated ambient temperatures, and the -I suffix denotes the industrial temperature grade. Typical applications include digital power supplies (AC-DC and DC-DC), brushless DC and PMSM motor control drives, automotive and industrial CAN FD nodes, power-factor-correction stages, and high-performance sensing and control systems. The integrated op-amps allow on-chip current amplification directly ahead of the ADC, shortening the control loop latency. Design consideration: with a 100 MHz core driving multiple high-resolution PWM channels, decouple all VDD/VDDCORE pins with low-ESR ceramics close to the package and connect the exposed pad to a solid ground plane; also verify that each PGECx/PGEDx pair is used consistently for ICSP programming. This page synthesizes distributor inventory data, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single citable reference for the DSPIC33CK256MP506T-I/MR.

USD $4.98 在庫あり