集積回路

サブカテゴリ

📁 ADC/DAC 2518 製品 📁 アンプIC 794 製品 📁 オーディオコーデック 16 製品 📁 オーディオIC 2 製品 📁 クロック＆タイミング 287 製品 📁 DSP 962 製品 📁 データ収集IC 2 製品 📁 デジタルポテンショメータ 4 製品 📁 ディスプレイドライバ＆コントローラ 1 製品 📁 FPGA & CPLD 6666 製品 📁 インターフェースIC 1568 製品 📁 LEDドライバ 1 製品 📁 ロジックIC 305 製品 📁 メモリIC 875 製品 📁 マイクロコントローラ 18688 製品 📁 マイクロプロセッサ 4 製品 📁 モータドライバ 1 製品 📁 その他 1 製品 📁 Sensor and Detector Interfaces 1 製品 📁 専用IC 15 製品 📁 ビデオIC 13 製品

製品 (32726)

TL074CDR - Quad Low-Noise JFET Op-Amp 14-SOIC | Texas Instruments
TL074CDR

TL074CDR - Quad Low-Noise JFET Op-Amp 14-SOIC | Texas Instruments

The Texas Instruments TL074CDR is a quad low-noise JFET-input general-purpose operational amplifier integrating four high-voltage JFET-input stages and bipolar transistors in a single 14-pin SOIC package. Each of the four channels delivers a typical gain bandwidth of 3 MHz, a slew rate of 13 V/us, and an equivalent input noise voltage of 18 nV/sqrt(Hz) at 1 kHz. The device operates from a single supply of 7 V minimum or dual supplies up to +/-18 V (absolute maximum 36 V), with output swing to within approximately 1.5 V of each rail on a +/-15 V supply. What is a JFET-input operational amplifier? A JFET-input op-amp (sometimes called a JFET op-amp or BiFET op-amp when JFET and bipolar are monolithically combined, as in the TL074) is a type of operational amplifier whose input stage uses JFET transistors instead of bipolar transistors. The JFET input delivers an extremely high input impedance (typically 10^12 ohm) and very low input bias current (typ. 30 pA), making the topology ideal for high-impedance sensor front-ends, audio preamplifiers, and integrator circuits. JFET-input op-amps sit within the operational amplifier taxonomy below general-purpose amplifiers and above specialty low-noise instrumentation amplifiers. Key features of the TL074CDR include internal frequency compensation, output short-circuit protection, latch-up-free operation, low total harmonic distortion, and a low offset-voltage temperature coefficient. The four independent channels share common power pins, eliminating the need for four separate single op-amps in dense multi-channel designs. The 'C' speed grade offers 3 MHz GBW and 13 V/us slew rate, while the 'B' grade and standard 'non-suffix' grade share the same channel architecture but vary in offset specifications. From a circuit-design standpoint, the TL074CDR is built on TI's mature BiFET-II process, which combines a JFET input differential pair with a bipolar output stage to deliver higher output drive (typ. 20 mA short-circuit output current) than all-JFET designs while preserving JFET-class input impedance. The internal compensation capacitor removes the need for external frequency-compensation components and guarantees unity-gain stability. Typical applications include audio preamplifiers and equalizers, active filters (Sallen-Key, multiple-feedback), signal conditioning for transducers, sample-and-hold buffers, professional audio mixers, and general-purpose signal-conditioning stages. The 14-SOIC package is pin-compatible with the legacy TL074 footprint and occupies roughly half the board area of a 14-DIP version while still supporting hand-soldering on standard 1.27 mm pitch land patterns. When designing with the TL074CDR, ensure that the input common-mode voltage stays within the specified input voltage range (VCC- + 4 V to VCC+ + 4 V on a single supply) and that the output stays below the absolute maximum supply rails. For ultra-low-noise instrumentation front-ends, consider the lower-noise OPA167x or OPA1612 family; for higher precision DC accuracy, consider the OPA2277.

見積もり お問い合わせ
TL082CDR - Dual 30V 3MHz JFET Op Amp | Texas Instruments
TL082CDR

TL082CDR - Dual 30V 3MHz JFET Op Amp | Texas Instruments

Texas Instruments TL082CDR is a dual JFET-input operational amplifier with a 30 V supply rating, 3 MHz gain-bandwidth product, and 13 V/us slew rate, supplied in an 8-pin SOIC package. Its two channels combine matched JFET and bipolar transistors in one monolithic IC, supporting general-purpose low-noise and high-input-impedance signal conditioning. A JFET-input operational amplifier is a voltage-amplifier device whose input stage limits input bias current while preserving low-noise behavior. In the broader semiconductor hierarchy, the TL082 belongs to the operational-amplifier class, then analog ICs, amplifiers, and signal-chain components. Its wide supply capability makes it suitable for industrial and instrumentation circuits operating from split or single positive rails up to the manufacturer's stated 30 V limit. The verified family description identifies the TL082 as a dual amplifier rated for 30 V operation with 3 MHz bandwidth and 13 V/us slew rate. These headline values provide enough bandwidth for audio, buffering, active filtering, sensor interfaces, and general feedback-control loops. Because the target is specified as TL082CDR, the package and order-code details should be confirmed against the Texas Instruments product page and manufacturer datasheet before production release. The device uses JFET-input transistors followed by bipolar signal-processing circuitry, providing high input resistance and relatively low input bias current. This input architecture is useful when driving high-impedance sources such as sensors, photodiodes, or measurement probes. The 3 MHz bandwidth also makes the amplifier suitable for small-signal stages rather than high-frequency, high-current, or power-amplifier applications. Typical uses include dual-channel audio preamplification, low-leakage sensor interfaces, active filters, sample-and-hold buffers, and dual feedback-control channels. Designers should pay attention to supply bypass, output-current limits, input common-mode range, output swing, stability with capacitive loads, and the exact pinout of the 8-SOIC package. Decoupling capacitors should be placed close to the supply pins to reduce parasitic inductance and preserve low-noise behavior. The principal design trade-off is flexibility versus precision: a general-purpose JFET input amplifier is easy to apply across many signals, but it may not match dedicated low-noise, low-offset, high-speed, or precision amplifier architectures. For replacement decisions, compare supply voltage, input bias current, offset voltage, bandwidth, slew rate, common-mode range, output swing, package pins, and required noise performance rather than relying only on the TL082 name. This page synthesizes the verified manufacturer description, distributor listings, package information, and practical selection considerations for engineers evaluating the TL082CDR. It also identifies which electrical and compliance values require confirmation from the manufacturer datasheet rather than inference.

見積もり お問い合わせ
TLC1541CDWRG4 - 10-Bit 32kSPS 11-Ch SAR ADC, SOIC-20 | TI
TLC1541CDWRG4

TLC1541CDWRG4 - 10-Bit 32kSPS 11-Ch SAR ADC, SOIC-20 | TI

The Texas Instruments TLC1541CDWRG4 is a 10-bit, 32-kSPS successive-approximation analog-to-digital converter with serial output and an integrated 11-channel analog multiplexer, housed in a 20-pin SOIC (DW) package supplied on tape and reel. The device offers 10-bit resolution with built-in self-test mode, software-controllable sample-and-hold, and on-chip system clock, supporting both microprocessor-peripheral and standalone operating modes. A successive-approximation register (SAR) ADC is a converter architecture that resolves one bit per clock cycle by comparing the sampled input against an internal binary-weighted DAC, settling in N cycles for an N-bit result. The TLC1541 belongs to the broader family of analog-to-digital converters (ADCs) within data-acquisition ICs, the function of mixed-signal semiconductors, and ultimately the semiconductor device category. The integrated 11-channel analog input multiplexer allows the part to scan up to 11 single-ended analog signals, replacing multiple single-channel ADCs and reducing board area and BOM cost in multi-sensor designs. Key specifications include 10-bit resolution, 32 kSPS maximum sample rate, 11 analog input channels, an analog input range of 0 V to 5.5 V (with proper external scaling), a 4.1 MHz internal system clock, and a serial interface compatible with most microcontrollers. The device operates from a single 4.5 V to 5.5 V supply, consumes approximately 6 mA during active conversion, and supports software-controlled power-down with a maximum standby current of 25 uA for battery-powered and duty-cycled applications. The TLC1541 uses a differential high-impedance reference input that facilitates ratiometric conversion, scaling, and analog-circuitry isolation from logic and supply noise. End-of-conversion (EOC) is signalled on a dedicated output pin, easing interrupt-driven sampling in microcontroller designs. The architecture is well-suited to industrial control loops where 10-bit resolution and 32 kSPS throughput are sufficient. Typical applications include multi-channel data-acquisition systems, industrial process control, battery monitoring, environmental sensor arrays, and panel-meter designs. Its wide supply tolerance and SOIC-20 footprint make it a practical choice for both retrofit and new designs. When designing with the TLC1541, ensure REF+ and REF- are bypassed with 10 uF and 0.1 uF capacitors placed close to the pins, and add a 100 nF decoupling capacitor on VCC to minimise digital switching noise coupling into the analog input. This page synthesizes distributor pricing, SOIC-20 drop-in alternatives, and practical design notes not collected in any single manufacturer datasheet or distributor listing.

見積もり お問い合わせ
TLC1541IFNG3 - 10-Bit, 32 kSPS, 11-Ch SAR ADC | Texas Instruments
TLC1541IFNG3

TLC1541IFNG3 - 10-Bit, 32 kSPS, 11-Ch SAR ADC | Texas Instruments

The Texas Instruments TLC1541IFNG3 is a 10-bit, switched-capacitor, successive-approximation-register (SAR) analog-to-digital converter (ADC) with 11 analog input channels and a serial interface, housed in a 20-pin PLCC (FN) J-lead package. It supports a sampling rate of 32 kSPS with an analog input voltage range of 0 V to 5.5 V (with 5 V supply), a 21 µs typical conversion time, and an integral linearity error of ±0.0977 % (1 LSB). The serial data interface uses a 3-state output and four control inputs (CS, I/O CLOCK, ADDRESS, and EOC), making the part usable as either a microprocessor peripheral or in a standalone mode. A SAR ADC is a successive-approximation analog-to-digital converter, a subtype of ADC architecture that performs a binary search across the analog input range using an internal sample-and-hold and a comparator. Within the broader hierarchy, SAR ADCs belong to the direct-conversion ADC family (versus delta-sigma, dual-slope, and pipeline ADCs) and are widely used in data acquisition, process control, and instrumentation applications where moderate resolution (8-16 bit) and low latency are required. The TLC1541 family, which includes 11 multiplexed input channels, was designed as a microprocessor peripheral or standalone data-acquisition front-end, with on-chip track-and-hold, internal clock, and self-test modes. Key features include 11 analog input channels (10 external + 1 self-test), on-chip 12-channel analog multiplexer, software-configurable unipolar/bipolar input modes, and a maximum linearity error of ±1 LSB at 10 bits. The device operates from a single +5 V analog supply with a separate digital supply pin for noise isolation. The 20-pin PLCC (J-lead, FN) package provides socket-friendly through-hole-style mounting on SMT boards, simplifying prototyping and field replacement compared with fine-pitch QFN packages. The architecture combines a charge-redistribution DAC for successive approximation with a sample-and-hold front-end, allowing it to settle a full 10-bit conversion in 21 µs. The serial interface (compatible with TMS320 and SPI-style peripherals) reduces pin count versus parallel-output ADCs of similar resolution, simplifying PCB routing on dense mixed-signal boards. The built-in self-test voltage (Vref) plus channel 11 self-test address enables on-command verification of converter integrity without external stimuli. Typical applications include multi-channel data acquisition front-ends, industrial process-control analog input modules, portable instrumentation and panel meters, and embedded sensor digitizers. The wide input range (0-5 V with 5 V supply) and bipolar-mode flexibility also suit transducer-signal conditioning for thermocouples, RTDs, and strain-gauge bridges through external signal conditioning. When designing with this part, place the analog and digital supply pins close to low-impedance decoupling (typically 10 µF bulk + 0.1 µF ceramic) and keep analog/digital ground returns separated to a single-point tie under the IC. The SAR input draws transient current during conversion, so source impedance above 1 kΩ may degrade linearity unless an external input buffer is added. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not collected in any single distributor listing or the manufacturer datasheet alone.

見積もり お問い合わせ
TLC2264CPWR - Quad 16V 710kHz Rail-to-Rail Op Amp | Texas Instruments
TLC2264CPWR

TLC2264CPWR - Quad 16V 710kHz Rail-to-Rail Op Amp | Texas Instruments

The Texas Instruments TLC2264CPWR is a quad, 16-V, 710-kHz rail-to-rail operational amplifier in a 14-pin TSSOP (PW) package, fabricated in TI's Advanced LinCMOS process. Each of the four channels delivers a gain bandwidth product of 710 kHz and a slew rate of 0.55 V/us, while output swing reaches both supply rails. The device operates from a single supply of 2.2 V to 16 V or split supplies of plus/minus 2.2 V to plus/minus 8 V, supporting modern low-voltage analog designs. What is a rail-to-rail op amp? A rail-to-rail operational amplifier is a specialized analog IC whose output voltage swing can reach (or come close to) both the positive and negative supply rails, maximizing dynamic range in low-voltage single-supply systems. Rail-to-rail amplifiers sit within the larger hierarchy of operational amplifiers -> linear amplifiers -> analog ICs -> signal conditioning, and they are critical building blocks in sensor interfaces, ADC drivers, and battery-powered equipment where every millivolt of headroom matters. Key specifications include 12 nV/sqrt Hz typical input-referred voltage noise at 1 kHz, 1 pA typical input bias current, and 500 uA maximum quiescent current per channel. The TLC2264 also features a common-mode input voltage range that includes the negative rail, fully specified single-supply and split-supply operation, and ESD-protected inputs. The TSSOP-14 footprint keeps board area low while exposing a thermal pad for modest heat dissipation at elevated ambient conditions. Architecturally, the Advanced LinCMOS process yields low input bias currents suitable for high-impedance sensor front-ends and pico-amp-level signals. The output stage design allows the swing to reach within millivolts of each rail at moderate load, enabling 12-bit and 14-bit ADC input ranges to be fully utilized in 5V systems. Typical applications include transducer amplification in industrial process control, signal conditioning for portable and battery-powered instrumentation, low-side current sensing, rail-splitting in single-supply ADC front-ends, and active filtering. Its low noise and low bias current also suit ECG monitor front-ends and other medical instrumentation requiring high input impedance. When designing with this op amp, place the supply bypass capacitor (typically 0.1 uF ceramic in parallel with 10 uF bulk) within 5 mm of the VCC+ and VCC- pins. For unity-gain buffer configurations, the output can lightly oscillate due to capacitive loading - isolate the output with a 50-ohm series resistor if driving long PCB traces or cables. This page synthesizes authentic distributor pricing, drop-in same-package alternatives, and practical design notes - the kind of consolidated engineering reference not found in the manufacturer datasheet alone.

見積もり お問い合わせ
TLC272CD - Dual 16V 2MHz CMOS Op-Amp | Texas Instruments
TLC272CD

TLC272CD - Dual 16V 2MHz CMOS Op-Amp | Texas Instruments

The Texas Instruments TLC272CD is a precision dual operational amplifier built on TI silicon-gate LinCMOS technology, delivering 2 MHz gain-bandwidth and 16 V maximum single-supply operation in an 8-pin SOIC package. It combines two rail-friendly CMOS op-amp channels with high input impedance, low input bias current, and low noise, with input common-mode range extending to the negative rail (In to V-). An operational amplifier (op-amp) is a high-gain voltage amplifier with differential inputs and a single-ended output, the foundational building block of the analog signal chain within the broader amplifier IC and power-management/signal-conditioning hierarchy. Single-supply CMOS op-amps such as the TLC272 family are optimized to operate directly from common logic and battery rails, where the input range must include ground (V-). Key features include a wide supply range over the specified temperature range (16 V single-supply operation), input offset voltage drift of typically 0.1 uV/month including the first 30 days, and very low input bias current due to the CMOS input stage, which yields very low noise current that is insignificant in most applications. The LinCMOS process provides excellent long-term offset stability without the input-current penalties of bipolar designs. Technically, the silicon-gate LinCMOS architecture keeps first-stage differential-pair current low; per the TLC27xx datasheet, noise performance in op-amp circuits depends strongly on this first-stage current, and the TLC272's low bias-current requirement results in minimal noise current. Speeds approach those of general-purpose BiFET amplifiers while retaining the input impedance advantages of CMOS. Typical applications include sensor signal conditioning and transducer interfaces (high-impedance inputs preserve signals from piezo and photodiode sources), active filters and integrators in battery-powered instrumentation, and general-purpose single-supply amplification in industrial and consumer control boards. Design consideration: as with any CMOS input, use appropriate input protection against electrostatic discharge and avoid letting inputs exceed the supply rails; the 2 MHz bandwidth means closed-loop gains above about 20 with adequate phase margin for stable, low-gain-error operation. This page synthesizes distributor availability data, verified drop-in alternatives within the TLC27xx family, and practical design notes beyond the headline specifications found in the manufacturer datasheet.

見積もり お問い合わせ
TLC272CDR - Dual 16V CMOS Op-Amp 2MHz SOIC-8 | Texas Instruments
TLC272CDR

TLC272CDR - Dual 16V CMOS Op-Amp 2MHz SOIC-8 | Texas Instruments

The Texas Instruments TLC272CDR is a precision dual operational amplifier fabricated on TI silicon-gate LinCMOS technology, offering 2 MHz (typ 2.2 MHz) bandwidth, 3.6 V/us slew rate, and single-supply operation from 3 V to 16 V in an 8-pin SOIC package. An operational amplifier (op-amp) is a high-gain voltage amplifier with differential inputs, forming the foundational building block of the analog signal chain within the broader hierarchy of amplifier ICs, linear ICs, and semiconductors. Rail-to-rail style input flexibility on single-supply parts like the TLC272 lets designers amplify sensor signals that swing near ground without a negative supply, dramatically simplifying battery-powered and industrial designs. Key features include a maximum input offset voltage of 500 uV at 25 C with VDD = 5 V, extremely low offset drift of typically 0.1 uV/month (including the first 30 days), very high input impedance with low bias currents inherent to CMOS inputs, and a common-mode input range that extends to the negative rail (In to V-). These characteristics make it a cost-effective alternative to BiFET general-purpose amplifiers. The LinCMOS process provides input bias currents in the picoampere range, enabling direct interfacing with high-impedance sources such as pH probes, photodiodes, and piezoelectric sensors without external buffering. The dual amplifier in one SOIC-8 saves board area and improves channel matching in filter and instrumentation circuits. Typical applications include sensor signal conditioning, active filters, battery-powered portable instrumentation, and low-frequency data-acquisition front ends where single-supply, low-bias-current operation is required. Design consideration: keep source impedances moderate and use adequate supply bypassing; the CMOS input is sensitive to static, so observe ESD handling precautions. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
TLC3544IPWR - 14-Bit 200kSPS 4-Ch SAR ADC | Texas Instruments
TLC3544IPWR

TLC3544IPWR - 14-Bit 200kSPS 4-Ch SAR ADC | Texas Instruments

The Texas Instruments TLC3544IPWR is a 14-bit, 200 kSPS, 4-channel successive-approximation analog-to-digital converter (SAR ADC) with single-ended/pseudo-differential unipolar inputs, housed in a 20-pin TSSOP (PW) package. The device operates from a single 5 V analog supply and a separate 3 V to 5 V digital supply, supports an analog input range of 0 V to AVdd (or 0 V to Vref when an external reference is used), and provides a serial (SPI/QSPI/MICROWIRE-compatible) interface for compact, low-pin-count designs. The -I suffix denotes the industrial -40C to +85C operating range. What is a SAR ADC? A successive-approximation analog-to-digital converter is a class of Nyquist-rate ADC that uses a binary-search algorithm and an internal capacitive DAC to digitize an analog input in N clock cycles for N-bit resolution. SAR ADCs sit within the broader hierarchy of analog-to-digital conversion (ADC) -> data converter -> data acquisition IC -> signal chain -> mixed-signal semiconductor, and they are preferred for medium-speed, medium-resolution applications where low power, deterministic latency, and small package footprint are critical. Key features include 200 kSPS maximum throughput, ±1 LSB INL (max) and ±1 LSB DNL (no missing codes), an SPI-compatible serial interface, hardware/serial shutdown (max 10 uA), a programmable MSB/LSB-first data format, and a hardware reset pin. A 2.5 V internal reference (10 ppm/C typical drift) is included, eliminating an external reference in many designs and reducing BOM cost. The pseudo-differential input topology simplifies PCB routing while preserving good common-mode rejection. Internally, the TLC3544IPWR combines a charge-redistribution capacitive DAC, a high-bandwidth comparator, and a successive-approximation register with on-chip clock generation. The 4 analog input channels are multiplexed into a single ADC core, and the digital serial interface isolates the analog section from bus noise. The architecture trades off absolute speed (200 kSPS) for exceptional linearity, low power (typically 30 mW at 5 V), and predictable latency that is deterministic on a per-conversion basis. Typical applications include multi-channel data acquisition systems, industrial process control, portable instrumentation, motor control feedback loops, optical sensor signal chains, and medical monitoring front-ends. The pseudo-differential 0-5 V input range matches most industrial transducer outputs (load cells, strain gauges, temperature bridges). When designing with this ADC, place 0.1 uF and 10 uF decoupling capacitors as close as possible to AVdd and DVdd pins, and use a ground plane with the analog and digital grounds joined at a single point under the IC. The REF+ pin must be bypassed with at least 10 uF (tantalum) in parallel with 0.1 uF (ceramic) to limit reference noise-induced conversion errors. The serial SCLK frequency must not exceed the device maximum at the chosen CS setup time. This page synthesizes distributor pricing, same-package (TSSOP-20) drop-in alternatives from the TI TLC3544 family, and practical reference-design notes not found in the manufacturer datasheet alone, giving engineers a single decision-grade resource for sourcing and design-in of this 14-bit SAR ADC.

見積もり お問い合わせ
TLC3544IPWRG4 - 14-bit 200kSPS 4-Ch Serial ADC | Texas Instruments
TLC3544IPWRG4

TLC3544IPWRG4 - 14-bit 200kSPS 4-Ch Serial ADC | Texas Instruments

The Texas Instruments TLC3544IPWRG4 is a 14-bit, 200-kSPS, 4-channel, single-supply serial analog-to-digital converter (SAR ADC) with pseudodifferential 0-5 V inputs, housed in a 20-pin TSSOP (PW) package. The G4 suffix designates a tape-and-reel packaging variant of the industrial-grade TLC3544IPW. It belongs to TI's TLC3544/TLC3548 family of low-power CMOS ADCs optimized for data acquisition systems requiring simultaneous high throughput and serial interface simplicity. An SAR (Successive Approximation Register) ADC is a precision data converter that performs a binary search through internal capacitor arrays to resolve an analog input to N bits in a single conversion cycle. SAR ADCs are widely favored for their deterministic latency, lack of pipeline delay, and excellent DC accuracy at moderate speeds, making them a standard choice for multiplexed-channel data acquisition, industrial process control, and instrumentation front-ends. The TLC3544 sits within the data converter hierarchy as: SAR ADC -> ADC -> data converter -> signal chain IC -> semiconductor. Key differentiating features include 14-bit resolution with no missing codes, four analog input channels multiplexed through an internal analog MUX, 200-kSPS maximum throughput, pseudodifferential input configuration spanning 0 V to the reference voltage, and a 5-V analog/3- to 5-V digital split supply architecture that simplifies mixed-signal PCB partitioning. The serial interface is a SPI/QSPI/MICROWIRE-compatible four-wire port that minimizes pin count and board routing in dense designs. The TLC3544 architecture combines a low-noise input sample-and-hold, a high-accuracy DAC for the SAR conversion loop, and a precision internal reference chain that scales with VREF. The device achieves strong AC performance with excellent differential non-linearity and low integral non-linearity for a 14-bit part, while typical power dissipation remains below the threshold for forced-air cooling in most embedded systems. Typical applications include multi-channel industrial data acquisition modules, factory automation sensor interfaces, portable or battery-powered measurement equipment, optical module monitoring, and process control I/O cards. The 4-channel input count matches common transducer clusters (e.g., four thermocouples, four strain gauges, four 4-20 mA loops) with a single ADC chip. Designers should plan decoupling on both AVDD and DVDD with 0.1 µF ceramic capacitors placed within 5 mm of the supply pins, keep analog and digital ground returns separated back at a single star point, and use a low-noise, low-drift external reference (e.g., REF3025 or REF5050) when system DC accuracy requires more than the internal reference can deliver. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
TLC3545IDGKR - 14-Bit 200kSPS SAR ADC, Serial Out | Texas Instruments
TLC3545IDGKR

TLC3545IDGKR - 14-Bit 200kSPS SAR ADC, Serial Out | Texas Instruments

The Texas Instruments TLC3545IDGKR is a 14-bit, 200-kSPS successive-approximation analog-to-digital converter (SAR ADC) with a serial SPI/QSPI/Microwire-compatible interface, a single pseudo-differential input channel, and an integrated auto-power-down mode, housed in an 8-pin MSOP PowerPAD (DGK) package. An SAR ADC (Successive Approximation Register Analog-to-Digital Converter) is a type of data converter that resolves a binary output one bit per clock cycle using a binary-weighted capacitor array and a comparator. SAR ADCs sit within the broader hierarchy: ADC -> data converter -> signal chain IC -> semiconductor. Compared to delta-sigma converters, SAR ADCs offer deterministic throughput and zero pipeline latency, which makes them well-suited to multiplexed acquisition, motor control loops, and any application where the sample timing must be tightly bounded. The TLC3545 samples at 200 kSPS from a single 5-V analog supply, draws only 5.8 mW at full speed, and drops to 10 uA in auto-power-down between conversions. The 8-pin MSOP PowerPAD package provides a low thermal-resistance path (theta_JA roughly 80 C/W with the pad soldered) so the converter can be placed next to digital logic without local heating concerns. Typical applications include industrial process-control front ends, optical encoder read-out boards, portable data loggers, and the analog input stage of DSP-based motor drives. Because the device is pin-compatible with the TLC3541 (12-bit) and other members of the TLC354x family, designers can swap resolution without re-laying-out the PCB. When designing with this part, place a 0.1 uF ceramic bypass capacitor within 5 mm of the AVDD pin and use the PowerPAD as the primary ground return for the analog input traces. The auto-power-down feature is enabled by tying CS high between conversions - this is the easiest way to drop average supply current in battery-powered systems. This page synthesizes distributor pricing, drop-in pin-compatible alternatives (TLC3545IDGKG4, TLC3545ID, TLC3545IDGK), and practical layout notes not found in the manufacturer datasheet front matter.

見積もり お問い合わせ
TLC4541IDRG4 - 16-bit 200kSPS Serial ADC, Auto PWDN, 8-SOIC
TLC4541IDRG4

TLC4541IDRG4 - 16-bit 200kSPS Serial ADC, Auto PWDN, 8-SOIC

The Texas Instruments TLC4541IDRG4 is a 16-bit, 200-kSPS successive-approximation-register (SAR) analog-to-digital converter (ADC) with a serial (SPI/DSP-compatible) output and an automatic power-down feature, housed in an 8-pin SOIC package (8-SOIC, 0.154 inch / 3.90 mm body width). A SAR ADC is a type of data-acquisition converter that uses a switched-capacitor binary-weighted DAC and a comparator to perform bit-by-bit conversion in N clock cycles for N bits of resolution. SAR ADCs combine low-latency single-shot acquisition, deterministic latency, and excellent DC accuracy, and they occupy a position in the data-converter hierarchy above flash and integrating ADCs but below pipelined and delta-sigma converters for very-high-speed or very-high-resolution tasks. Key features of the TLC4541IDRG4 include 16-bit resolution with no missing codes, 200-kSPS throughput, single +5V analog supply, a single-ended analog input channel with pseudo-differential sampling, and a synchronous serial interface that connects directly to DSPs, microcontrollers, and SPI peripherals. The device also provides hardware-controllable auto power-down between conversions that reduces supply current to microamp levels and an industrial-grade temperature range of -40C to +85C. Internally, the TLC4541 uses a charge-distribution CDAC, an on-chip clock generator, and a precision comparator to perform conversions. The on-chip digital interface includes a 16-bit shift register that delivers MSB-first data with an external serial clock, eliminating the need for an external high-frequency clock. An external reference voltage of typically 4.096 V (or any value up to AVDD) sets the input full-scale range. Typical applications for the TLC4541IDRG4 include industrial process-control front ends, isolated 4 mA to 20 mA loop digitizers, multi-channel data-acquisition systems where multiple ADCs share a SPI bus, handheld instrumentation and battery-powered meters that benefit from the auto power-down, and digital signal processor (DSP) sensor interfaces. When designing with this ADC, place the 10 uF bulk and 0.1 uF decoupling capacitors as close as possible to AVDD and DVDD pins, keep the analog input traces short and guarded, and use an external low-noise reference such as the REF5040 or REF3120 to obtain full 16-bit performance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
TLC4545IDGKR - 16-Bit 200kSPS Serial ADC | Texas Instruments
TLC4545IDGKR

TLC4545IDGKR - 16-Bit 200kSPS Serial ADC | Texas Instruments

The Texas Instruments TLC4545IDGKR is a 16-bit, 200 kSPS, low-power, single-channel successive-approximation-register (SAR) analog-to-digital converter (ADC) with a pseudo-differential analog input and a serial (SPI-compatible) digital interface, housed in an 8-pin VSSOP (DGK) package on tape-and-reel. The device operates from a single 5 V analog supply, draws only 2.94 mW of typical power at 200 kSPS, and features an automatic power-down mode that reduces supply current to 1 uA between conversions, making it well suited for battery-powered and portable data-acquisition front ends. An SAR ADC is a precision data converter that performs a binary-search conversion cycle against a capacitive reference network. Within the broader component taxonomy, an SAR ADC sits under ADC -> data converter -> mixed-signal IC -> semiconductor. Compared with delta-sigma ADCs, SAR converters offer deterministic latency and excellent DC accuracy without the digital filtering delays, which makes them a preferred choice for multiplexed multi-channel systems, control loops, and instrumentation that demand both speed and step-response integrity. Key specifications of the TLC4545IDGKR include 200 kSPS maximum throughput, a 16-bit no-missing-code resolution, a 2.94 us typical conversion time, 1 LSB integral nonlinearityty (INL) maximum, and a SINAD figure that supports industrial measurement precision. The pseudo-differential input architecture accepts unipolar 0-5 V signals while rejecting common-mode noise on the ground return, and the 3-wire serial interface (CS, SCLK, SDO) glues directly to most DSPs, microcontrollers, and FPGAs without external glue logic. The internal architecture combines a track-and-hold front end with an internal 5 V reference option and a precision SAR core, all trimmed at the factory to specified linearity limits. An auto-power-down state machine gates the analog bias currents between active conversion cycles, controlled transparently by the serial chip-select input, so the host MCU can throttle the conversion rate without changing firmware overhead. Typical applications for the TLC4545IDGKR include portable industrial data loggers, sensor signal conditioning stages, multi-channel thermocouple or strain-gauge front ends, battery chargers, optical encoder interfaces, and remote instrumentation that interfaces directly to 5 V-tolerant microcontrollers. Its 16-bit resolution, low power dissipation, and tiny VSSOP-8 footprint also suit dense PCB designs such as point-of-care medical monitors and smart sensor modules. When designing with this part, place the analog and digital grounds on a split ground plane joined at a single point beneath the IC, decouple AVDD with a 10 uF bulk plus 0.1 uF ceramic capacitor within 5 mm of the pin, and keep the serial-interface traces short and impedance-controlled. The auto-power-down feature can be disabled by holding CS low between conversions if the application requires maximum sample-rate throughput. This page synthesizes distributor pricing, drop-in cross-reference alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single source for selection, sourcing, and bring-up.

見積もり お問い合わせ
TLC4545IDGKRG4 - 16-bit 200kSPS Serial ADC | Texas Instruments
TLC4545IDGKRG4

TLC4545IDGKRG4 - 16-bit 200kSPS Serial ADC | Texas Instruments

The Texas Instruments TLC4545IDGKRG4 is a 16-bit, 200-kSPS, low-power, single-channel successive-approximation analog-to-digital converter (ADC) with a serial (SPI/QSPI/Microwire-compatible) interface and automatic power-down, housed in an 8-pin MSOP (DGK) package. Operating from a single 5 V analog supply, the part combines a pseudo-differential analog input, an internal sample-and-hold, and an auto-power-down mode that drops quiescent current after each conversion to support battery-powered and duty-cycled data-acquisition designs. The suffix IDGKRG4 decodes as: I = industrial temperature grade (-40 to +85 °C), DGK = MSOP-8 package, R = large-reel (Tape & Reel), G4 = Pb-free / green (RoHS-compliant) finish. A successive-approximation register (SAR) ADC is a sampling converter that resolves a single bit per clock cycle by comparing the sampled input against an internal binary-weighted DAC, achieving low latency (one conversion cycle), deterministic throughput, and inherent anti-alias robustness when paired with an external input RC. SAR ADCs sit between slow-precision integrating converters (e.g., 24-bit sigma-delta) and fast flash converters, occupying the dominant position in multiplexed data-acquisition, motor control, and industrial instrumentation where 12-to-18 bit resolution is needed at sample rates from 1 kSPS to 1 MSPS. Key features include 200 kSPS throughput with a 2.94 µs maximum conversion time, ±1 LSB DNL (no missing codes), a serial data output (SDO) with chip-select (CS) and serial clock (SCLK), automatic power-down between conversions, and an internal 5 MHz serial clock requirement. The pseudo-differential input structure allows the converter to reject small common-mode ground noise between the analog source and the ADC ground, and the internal reference is ratiometric to VREF, simplifying system design. The architecture combines a charge-redistribution capacitive DAC with a low-noise comparator and on-chip clock generator, achieving true 16-bit performance with no missing codes at 200 kSPS. The auto-power-down state reduces current between conversions, extending battery life in portable instruments. The serial interface minimizes host-side pin count and is directly compatible with most microcontrollers and DSP serial ports without glue logic. Typical applications include portable data loggers, industrial process-control analog input modules, weigh-scale front ends, sensor signal conditioning, optical sensor read-out, motor control feedback, and general-purpose precision instrumentation. The pseudo-differential input also makes the device well-suited to thermocouple and bridge-sensor front ends when paired with an external instrumentation amplifier. When designing with the TLC4545, keep the analog input traces short, place the input bypass capacitor (typically 10 µF tantalum + 0.1 µF ceramic) close to the analog supply pin, and provide a clean reference to VREF for ratiometric measurements. Note that the suffix "G4" indicates Pb-free reel packaging only - the silicon and electrical performance are identical to the standard TLC4545IDGKR variant. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

見積もり お問い合わせ
TLC540IDWR - 8-Bit 75kSPS SAR ADC, 11-Input MUX, 20-SOIC | TI
TLC540IDWR

TLC540IDWR - 8-Bit 75kSPS SAR ADC, 11-Input MUX, 20-SOIC | TI

The Texas Instruments TLC540IDWR is an 8-bit, 75 kSPS successive-approximation analog-to-digital converter with an integrated 12-channel (11 external + 1 self-test) analog multiplexer and a synchronous serial interface, housed in a 20-pin SOIC (DW) package. The serial output drives up to four control inputs including an independent system clock, and an on-chip analog MUX supports up to eleven single-ended analog inputs. Built-in self-test mode, software-controllable power down, and a -40C to +85C industrial temperature range make the part well suited to data-acquisition front ends on microprocessors or DSP peripherals. A Successive-Approximation Register (SAR) ADC is a converter architecture that performs a binary search on the input voltage through an internal DAC, yielding one conversion in N clock cycles for an N-bit result. SAR converters are valued for deterministic latency and absence of pipeline delay, which lets the same architecture scale from 8 to 18 bits without architectural changes. Within the broader taxonomy this part sits under data converters > ADC > SAR ADC > single-channel SAR with integrated MUX, a category dominated by TI's TLC540/TLC541/TLC1541 family and pin-compatible follow-ons. Key differentiating features include 8-bit resolution with 75 kSPS maximum sample rate, an input MUX that expands a single ADC into eleven analog channels, low conversion time (~17 us typical), software-controlled power down (typically 4 mW active vs sub-mW in shutdown), and a serial interface compatible with TMS320 DSPs and most microcontrollers. A self-test mode exercises the analog path against an internal reference voltage, an unusual feature at this resolution/price point that simplifies production-time board test. The TLC540/541 family uses a switched-capacitor charge-redistribution DAC at the core of the SAR loop, with a precision analog MUX feeding a single high-impedance input. The serial interface uses chip-select, I/O clock, and data-out lines with the option of synchronous or asynchronous operation. Single +5V supply operation removes the need for negative rails, simplifying analog front-end design in 5V-only industrial systems. Typical applications include multi-channel sensor monitoring in industrial process control, scanned battery-cell voltage measurement in multi-cell battery management, keypad and panel-meter scanning in low-cost human-interface designs, and portable instrumentation where the on-chip MUX reduces BOM against a discrete MUX + ADC pair. When designing with the TLC540IDWR, allocate at least four I/O clock cycles per sample and ensure CS/FS (chip-select / frame-sync) timing matches the host DSP. A 0.1 uF decoupling capacitor must be placed within 5 mm of the VCC pin; analog and digital grounds should be tied at a single star point under the device to limit digital-coupling noise on the multiplexer. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with values verified against TI's TLC540 datasheet and current DigiKey/Mouser stock as of 2026-10-15.

見積もり お問い合わせ
TLC541INSG4 - 8-Bit 40kSPS 11-Ch Serial ADC | Texas Instruments
TLC541INSG4

TLC541INSG4 - 8-Bit 40kSPS 11-Ch Serial ADC | Texas Instruments

The Texas Instruments TLC541INSG4 is an 8-bit, 40 kSPS successive-approximation analog-to-digital converter (ADC) with 11 analog input channels and a serial (SPI/QSPI/MICROWIRE-compatible) data interface, housed in a 20-pin SOIC (NS) package. It operates from a single 5 V analog supply with a digital supply range of 4.5 V to 5.5 V, supports an input analog range of 0 V to 5 V, and is rated for industrial temperature operation from -40 °C to +85 °C. The on-chip 12-channel analog multiplexer allows direct connection of up to 11 external sensors plus one internal self-test channel. What is an ADC? An analog-to-digital converter (ADC) is a semiconductor device that transforms continuous analog voltage signals into discrete digital codes, enabling microcontrollers, microprocessors, and DSPs to process real-world signals. Successive-approximation (SAR) ADCs use an internal DAC and comparator to converge on the input voltage bit-by-bit in a fixed number of clock cycles, providing deterministic latency and excellent DC accuracy. The TLC541 belongs to the SAR ADC product family within the broader data-converter (ADC/DAC) category of signal-chain integrated circuits. Key features include 40 kSPS maximum sampling rate, ±0.5 LSB integral linearity error (0.1953 % typical linearity error), 17 µs conversion time, on-chip sample-and-hold, software-configurable analog channel selection, and a hardware reset input. The serial interface reduces pin count versus parallel-output ADCs and simplifies isolation in industrial designs. Built-in self-test mode verifies internal reference integrity without external instrumentation, supporting safety-critical calibration routines. The TLC541 uses a switched-capacitor charge-redistribution SAR architecture with an internal reference and sample-and-hold amplifier. Its CMOS implementation yields low analog-input leakage (typically <1 µA) and low digital-interface power draw, allowing direct connection to 5 V microcontrollers such as the TI MSP430 and classic 8051 family. The 20-pin SOIC footprint simplifies PCB layout on standard 0.1" grid prototyping boards. Typical applications include multi-channel data acquisition front-ends in industrial process control, portable instrumentation with battery monitoring, factory-automation sensor multiplexing, HVAC multi-zone temperature and pressure monitoring, automotive body-controller analog sensing, and medical-grade low-speed signal digitisation where 8-bit resolution is acceptable. When designing with this device, decouple the analog and digital supplies with separate 0.1 µF ceramic bypass capacitors placed as close as possible to the AVDD and DVDD pins. Use short, guarded analog traces to minimise crosstalk between channels, and add an external RC filter on each analog input when driving from high-impedance sources. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

見積もり お問い合わせ
TLC542CDWG4 - 8-Bit 25kSPS Serial 11-Input SAR ADC | Texas Instruments
TLC542CDWG4

TLC542CDWG4 - 8-Bit 25kSPS Serial 11-Input SAR ADC | Texas Instruments

The Texas Instruments TLC542CDWG4 is an 8-bit, successive-approximation analog-to-digital converter with 11 analog input channels and a serial interface, housed in a 20-pin SOIC (DW) package with gull-wing leads. It supports a sampling rate of 25 kSPS, operates from a single 5V analog supply (with a separate digital supply option), and targets 0C to 70C commercial temperature environments. The converter is built around a switched-capacitor SAR core with on-chip 12-channel analog multiplexer (11 external inputs plus one for self-test), making it suited for microprocessor-peripheral or stand-alone ADC operation. An SAR ADC is a successive-approximation-register analog-to-digital converter that performs a binary search through internal capacitor-DAC weighting to settle one bit per clock cycle, achieving 8 bits of resolution in 8 conversion cycles. Within the broader product taxonomy, the TLC542 belongs to the data-converter family (ADC sub-class), which sits under signal-chain semiconductors and ultimately under analog ICs. Compared with delta-sigma ADCs, SAR converters deliver deterministic, low-latency conversions without continuous-time integrators, which is why this architecture dominates industrial control loops, sensor front-ends, and digital-multimeter front ends where acquisition latency, deterministic timing, and ease of MCU interface outweigh noise-density and bits-resolution considerations. Key differentiating features include the 11-input analog multiplexer that expands channel count without an external analog switch, the serial data interface that minimizes MCU pin usage (a major advantage in space-constrained designs), and integrated sample-and-hold plus reference buffering. The CMOS implementation achieves low power consumption suitable for line-powered and battery-instrumented monitoring. The 20-pin SOIC (DW) package provides a 7.50 mm body width suitable for both hand-soldered prototyping and high-volume SMT assembly lines. Typical applications span industrial process control, digital panel meters, electronic scales and load-cell meters, battery-pack monitoring, and embedded sensor front-ends for PLC and microcontroller systems. Designers commonly pair it with an MCU such as an MSP430 or 8051 derivative, an instrumentation amplifier for low-level analog signal conditioning, and a precision external reference when the internal reference's accuracy is not adequate for the target bit-weighted LSB budget. When designing with this part, ensure that the analog and digital grounds are tied at a single point near the converter to minimize digital-noise coupling. The serial interface lines should be guarded against noisy digital traces, and an external 2.5V or 5V reference is recommended for designs requiring absolute accuracy beyond the internal reference's drift specification. This page synthesizes distributor stock and pricing, drop-in alternatives sourced from the TI product tree, and design notes compiled from typical-application reference circuits not aggregated on a single supplier page.

見積もり お問い合わせ
TLC542IFNRG3 - 8-Bit 25kSPS 11-Ch SAR ADC | Texas Instruments
TLC542IFNRG3

TLC542IFNRG3 - 8-Bit 25kSPS 11-Ch SAR ADC | Texas Instruments

The Texas Instruments TLC542IFNRG3 is an 8-bit, 25 kSPS successive-approximation analog-to-digital converter (SAR ADC) with an on-chip 11-channel analog multiplexer and serial interface, housed in a 20-pin PLCC (J-lead) package rated for the -40C to +85C industrial temperature range. Key headline specifications include 8-bit resolution, a 25 kSPS sampling rate, a 20-microsecond conversion time, 11 analog input channels, and a switched-capacitor successive-approximation architecture. The serial output uses a 3-state interface that connects directly to a microprocessor or DSP through three inputs: I/O CLOCK, CS (chip select) and ADDRESS (with serial data output on the I/O CLOCK line). An SAR ADC is a type of data converter that uses a binary-search algorithm against an internal DAC to resolve each input voltage into a digital code in N clock cycles (where N is the resolution in bits). SAR ADCs typically outperform integrating or delta-sigma converters on speed and latency, at the cost of resolution, and are widely used in embedded data acquisition, motor control, sensor read-out, and instrumentation front-ends. Within the converter hierarchy, SAR sits between fast flash ADCs (low resolution, very high speed) and delta-sigma ADCs (high resolution, lower speed), making 8-bit 25 kSPS parts a sweet spot for cost-sensitive multi-channel monitoring. The TLC542IFNRG3 is built on a CMOS switched-capacitor process that integrates the sample-and-hold into the SAR core, eliminating external track/hold circuitry. Built-in features include software-configurable analog input multiplexer addressing, a sample-and-hold, internal reference, and a serial I/O port that simplifies PCB layout by replacing wide parallel data buses with a single serial link. Typical applications include multiple sensor monitoring, process control front-ends, battery-cell voltage monitoring, isolated data acquisition modules, portable instrumentation, and consumer electronics such as appliance control boards where a small MCU needs to read several analog points without consuming many GPIO pins. When designing with this part, note that the input multiplexer allows one of 11 channels to be addressed through a single serial write, and the previous conversion result is read on the same clock edge - this time-multiplexed protocol keeps host pin count low. Decouple VCC close to the package with at least 0.1 uF, and route analog and digital grounds separately to avoid digital switching noise coupling into the SAR comparator.

見積もり お問い合わせ
TLC545ING4 - 8-Bit 76 kSPS ADC, 19-Ch Serial, 28-DIP | TI
TLC545ING4

TLC545ING4 - 8-Bit 76 kSPS ADC, 19-Ch Serial, 28-DIP | TI

The Texas Instruments TLC545ING4 is an 8-bit, 76 kSPS successive-approximation analog-to-digital converter with a 19-input analog multiplexer and a serial interface, housed in a 28-pin PDIP (0.600 inch / 15.24 mm) through-hole package. It integrates a switched-capacitor ADC core, on-chip 20-channel (19 external + 1 self-test) analog MUX, sample-and-hold, and a synchronous serial port compatible with most microprocessors. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that converts a continuous analog voltage on one of its input pins into a discrete binary code. Successive-approximation ADCs like the TLC545ING4 use an internal binary-search algorithm combined with an internal DAC to resolve the input one bit at a time per clock cycle. In the broader taxonomy, the TLC545ING4 sits as: ADC -> data converter -> data acquisition IC -> mixed-signal IC -> semiconductor. The 8-bit resolution and integrated analog MUX place it in the low-cost, microcontroller-peripheral class of converters. Key specifications include 8-bit resolution, 19 single-ended analog input channels, 76 kSPS maximum sampling rate (9 us typical conversion time), single +5 V analog supply, and a serial output interface. Operating temperature spans -40 C to +85 C (industrial grade). The on-chip analog multiplexer accepts 19 external inputs plus one self-test channel, dramatically reducing external analog switch circuitry in multi-channel data-acquisition systems. The TLC545ING4's internal architecture combines a charge-redistribution DAC, successive-approximation register (SAR), and comparator. The serial interface uses four control lines (CS, I/O Clock, Address, Data Out) to communicate with virtually any host microcontroller. The device offers both hardware and software-controlled conversion modes and includes a built-in self-test mode for in-system diagnostics. Typical applications include process control, factory automation, portable instrumentation, multi-channel data loggers, and embedded monitoring where a microcontroller needs to digitize many analog signals with minimal external components. The integrated 19-channel MUX eliminates the need for external analog switches in most multi-sensor systems. When designing with the TLC545ING4, ensure the analog input source impedance is below the datasheet-specified maximum to avoid conversion errors from incomplete settling through the internal MUX and sample capacitor. Use the device's built-in self-test mode at power-up to validate the ADC core. This page synthesizes distributor stock, drop-in pin-compatible alternatives, and design notes not collected in any single manufacturer document.

見積もり お問い合わせ
TLC549CD - 8-Bit 40kSPS SAR ADC Serial Out | Texas Instruments
TLC549CD

TLC549CD - 8-Bit 40kSPS SAR ADC Serial Out | Texas Instruments

The Texas Instruments TLC549CD is an 8-bit, 40-kSPS successive-approximation analog-to-digital converter with a serial 3-state data output, housed in an 8-pin SOIC (D) package. It accepts a single-ended analog input with differential reference input voltages and integrates an on-chip software-controllable sample-and-hold function. Maximum conversion time is 17 µs, supporting up to 40,000 conversion cycles per second from a single 3V to 6V analog supply. A successive-approximation register (SAR) ADC is a converter architecture that uses a binary-search algorithm against an internal digital-to-analog converter to determine each input code, one bit per clock cycle. Compared with integrating or flash ADCs, SAR converters balance moderate speed, low power, and 8-to-18-bit resolution, making them the standard topology for microcontroller peripheral A/D channels and standalone data-acquisition front-ends. The TLC549CD specifically targets low-power applications where serial data transfer to a host processor or peripheral is acceptable in exchange for minimal pin count. Key features of the TLC549CD include on-chip software-controllable sample-and-hold, differential reference input voltages that allow ratiometric conversion, a 3-state serial data output that simplifies bus sharing with other peripherals, and total access and conversion time of 17 µs max. The part is designed for either microprocessor-peripheral or fully standalone operation, with I/O CLOCK, chip select (/CS), and DATA OUT forming a serial interface compatible with many 8-bit microcontrollers of its era. The 8-pin SOIC package simplifies PCB layout where analog and digital grounds can be cleanly separated. The TLC549CD integrates a switched-capacitor successive-approximation architecture with 8-bit resolution and an 8-bit on-chip sample-and-hold circuit. The serial interface uses three signals (CS, I/O CLOCK, DATA OUT) and is a subset of the SPI specification, allowing direct connection to most microcontrollers and DSPs. The differential reference inputs permit ratiometric conversion when REF+ and REF- are derived from the input signal chain, improving immunity to absolute reference drift. Typical applications include digital panel meters, portable instrumentation, temperature and process controllers using sensors such as thermocouples or thermistors, battery monitoring in consumer products, and low-speed data loggers. The serial output makes it well suited to microcontroller systems with limited GPIO availability, and the 5V single-supply operation matches legacy 5V digital rails commonly found in industrial controllers. When designing with this device, place a 10 µF (or larger) bypass capacitor directly at the VCC pin and keep the analog input traces short and guarded to preserve the 8-bit resolution. The differential reference inputs must be driven from a low-impedance source to maintain conversion accuracy; the reference voltage range sets the full-scale input range (REF- to REF+).

見積もり お問い合わせ
TLC549IDR - 8-Bit 40kSPS Serial SAR ADC | Texas Instruments
TLC549IDR

TLC549IDR - 8-Bit 40kSPS Serial SAR ADC | Texas Instruments

The Texas Instruments TLC549IDR is an 8-bit, 40 kSPS serial-output successive-approximation analog-to-digital converter (ADC) housed in an 8-pin SOIC package. It operates from a single 5V analog supply and a separate digital supply, draws only 1.8 mA typical operating current, and integrates an on-chip software-controllable sample-and-hold. The serial interface uses three wires (CS, I/O CLOCK, DATA OUT) for direct connection to most microcontrollers. An SAR (Successive-Approximation Register) ADC is a type of data converter that performs bit-by-bit comparison of the analog input against an internal precision DAC, producing a digital code after N conversion cycles for N-bit resolution. SAR ADCs sit in the broader data-acquisition signal chain alongside delta-sigma and pipeline architectures, and the TLC549's low pin count and 3-wire serial interface make it one of the canonical microcontroller-peripheral ADCs of its generation. Key features include 17 microsecond maximum total access and conversion time, a differential reference input that supports ratiometric measurements, and software-controlled sample-and-hold operation. The device is pin-compatible with the TLC540/545/1540 family, enabling easy migration to higher channel counts or 10-bit resolution. Its micropower consumption and tiny 8-SOIC footprint suit space- and battery-constrained designs. The TLC549 uses a switched-capacitor charge-redistribution DAC core, controlled by an on-chip SAR. Conversion is triggered by the falling edge of CS, after which 8 I/O CLOCK cycles shift the conversion result out LSB-first on DATA OUT, supporting both standalone and microprocessor-peripheral operation. Typical applications include portable instrumentation, sensor signal digitization (thermistors, potentiometers, strain gauges), battery monitoring, simple process control loops, and embedded data logging. Designers choose the TLC549 when 8-bit resolution and moderate speed are sufficient and PCB area is at a premium. When designing with this device, place 0.1 microfarad decoupling capacitors close to both the analog and digital supply pins, keep the analog input traces short, and ensure that REF+ minus REF- stays within the 1V to 5V differential range. Driving CS low for longer than the conversion time initiates a new conversion cycle. This page synthesizes distributor pricing, drop-in compatible alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers evaluate the TLC549IDR for new designs and legacy system maintenance.

見積もり お問い合わせ
TLC549IDRG4 - 8-Bit 40kSPS Serial ADC | Texas Instruments
TLC549IDRG4

TLC549IDRG4 - 8-Bit 40kSPS Serial ADC | Texas Instruments

The Texas Instruments TLC549IDRG4 is an 8-bit successive-approximation (SAR) analog-to-digital converter (ADC) with a serial interface, offering 40 kSPS sampling rate in an 8-pin SOIC (D) package. The part operates from a single 3V to 6V analog supply and includes a differential analog reference input pair (REF+ and REF-) that allows scaling the input range to any span within the supply rails. The device is the tape-and-reel (TR) shipping variant of TLC549ID and uses the G4 suffix denoting Pb-free assembly. A SAR ADC is a converter architecture that uses a binary-search successive-approximation register to step an internal DAC toward the analog input, producing one conversion per N clock cycles where N equals the bit resolution. Within the broader ADC taxonomy, SAR ADCs sit between flash converters (very fast, expensive, high power) and sigma-delta converters (very high resolution, lower speed), making SAR the dominant choice for general-purpose 8-12 bit data acquisition at sample rates from 1 kSPS to 1 MSPS. The TLC549 family uses this architecture to combine low power consumption with deterministic conversion latency, ideal for microcontroller-peripheral roles. Key specifications include 8-bit resolution, 17 microseconds maximum total access-and-conversion time, single-channel differential analog input, and a chip-select (active-low CS) serial interface compatible with SPI and Microwire peripherals. Per the TI datasheet, the converter draws approximately 1.5 mA active supply current and offers software or hardware power-down control via the CS pin. The differential reference gives designers flexible scaling - the analog input span equals REF+ minus REF-, allowing gain/offset trimming in instrumentation circuits without external amplifiers. Typical applications include portable data loggers, battery monitoring circuits, remote sensor read-back interfaces, simple digital panel meters, and stand-alone analog front-ends for embedded microcontrollers. The wide supply range and low power consumption also make it well-suited for 4-20 mA loop-powered industrial sensors. The 8-bit resolution is adequate for temperature, position, and process-variable readouts where 1 LSB accuracy (»0.4% FS at 5V reference) is acceptable. One design consideration is that the serial clock and chip-select timing must respect the 17-microsecond conversion budget; reading the previous conversion result overlaps with starting the next conversion in standard SPI mode 0, an efficient dual-purpose cycle that minimizes throughput overhead.

見積もり お問い合わせ
TLC5540CPWRG4 - 8-Bit 40 MSPS Flash ADC, 24-TSSOP | Texas Instruments
TLC5540CPWRG4

TLC5540CPWRG4 - 8-Bit 40 MSPS Flash ADC, 24-TSSOP | Texas Instruments

The Texas Instruments TLC5540CPWRG4 is an 8-bit, 40-MSPS (megasamples per second) flash analog-to-digital converter (ADC) with a single input channel and internal sample-and-hold, housed in a 24-pin TSSOP (PW) package. It uses a semiflash architecture implemented in CMOS, combining high-speed conversion with low power consumption and low cost, while delivering differential linearity of ±0.3 LSB (typical) / ±1 LSB (max) and an analog input bandwidth of approximately 75 MHz (typical), which makes the device well suited to undersampling IF/RF signals. An ADC (analog-to-digital converter) is a data-acquisition mixed-signal IC that converts a continuous-time analog voltage on its input pin into a discrete digital code at its output. Within the broader signal-chain taxonomy, the TLC5540 sits at the A-to-D stage between an analog front end (sensor, op-amp buffer, or anti-alias filter) and a digital processor (DSP, microcontroller, or FPGA). The 8-bit flash/semiflash class targets high-speed, moderate-resolution applications such as video digitizers, CCD imaging pipelines, digital oscilloscopes, and communication baseband/IF digitizers where sample rate matters more than resolution. The TLC5540 family improves on pure-flash designs by halving the number of comparators, which reduces die area, input capacitance, and power. Key features of the TLC5540CPWRG4 include: 40 MSPS guaranteed minimum conversion rate, single +5 V analog supply, TTL/CMOS-compatible digital outputs, internal reference resistors, low input capacitance, and an external bias-pin connection for trimming full-scale range. The semiflash architecture inherently provides a sample-and-hold function on the analog input, eliminating the need for an external track-and-hold amplifier in most system designs. Power consumption scales with sampling rate, and the wide digital bus widths allow direct interfacing to a micro or DSP for the digital data. Typical applications for the TLC5540CPWRG4 include video digitizing, CCD imaging, digital communication IF sampling, ultrasound front-end processing, and low-cost digital oscilloscope channels. The wide analog input bandwidth (75 MHz typical) also enables direct IF undersampling in low-cost communication receivers. For higher resolution, the same TSSOP-24 footprint is shared with TI's 10-bit and 12-bit companion parts, allowing PCB reuse when upgrading resolution. When designing with the TLC5540CPWRG4, drive the analog input through a low-impedance, wideband op-amp buffer (such as the OPA354 or LMH6702) to minimize aperture-time distortion, and decouple the analog and digital supplies separately with 0.1 µF ceramic capacitors placed close to the supply pins. Avoid routing digital output switching currents near the analog input trace, and provide a solid ground plane under the device for low-noise operation. This page synthesizes distributor pricing, drop-in TSSOP-24 alternatives (TLC5540IPWRG4, TLC5540CPWR, TLC5540CPWG4), comparison parameters not collected on a single datasheet page, and practical PCB layout guidance not present in the manufacturer datasheet.

見積もり お問い合わせ
TLE2022IDR - Dual Precision Low-Power Op Amp | Texas Instruments
TLE2022IDR

TLE2022IDR - Dual Precision Low-Power Op Amp | Texas Instruments

The Texas Instruments TLE2022IDR is a dual precision, high-speed, low-power operational amplifier built on TI's Excalibur bipolar process, housed in an 8-pin SOIC (D) package and rated for the industrial -40C to +85C temperature range. It delivers 2 circuit channels with low offset voltage, high unity-gain bandwidth, and low power consumption typical of the Excalibur family, making it suitable for general-purpose precision signal conditioning from a single supply. The part is specified as a standard (general-purpose) amplifier in TI's amplifier portfolio. What is an operational amplifier (op amp)? An op amp is a high-gain DC-coupled electronic voltage amplifier with differential inputs and, typically, a single-ended output. It is one of the most ubiquitous building blocks in analog electronics, sitting below instrumentation amplifiers and active filters in the signal-chain hierarchy and above individual transistors in functional abstraction. Precision low-power single-supply op amps such as the TLE2022 family are optimized for systems that must operate from a single positive rail (often 3.3V or 5V) while still delivering DC accuracy and AC bandwidth close to what dual-supply parts achieve. Key features of the TLE2022IDR include two independent op-amp channels in a single SOIC-8 footprint, low power consumption characteristic of the Excalibur process, high-speed response relative to competing low-power op amps, unity-gain stability, and support for single-supply operation. The complementary bipolar process uses isolated vertical PNP transistors that improve input common-mode range and slew rate versus older designs, which is one reason the TLE2022 family remains popular as a successor to the OP21 in legacy designs. Typical applications include active filters, precision integrators, sample-and-hold front ends, transducer signal conditioning, and battery-powered instrumentation. The 8-pin SOIC footprint is industry standard, allowing easy hand prototyping and high-density SMT assembly on the same PCB land pattern used by countless alternative dual op amps. When designing with this device, observe the datasheet maximum supply rating and provide proper input common-mode biasing when used on a single supply; the lower rail of the input common-mode range may not extend all the way to ground. Decouple the supply pin close to the IC with at least 0.1 uF ceramic capacitance. A unity-gain stable part can be operated without compensation but should be kept clear of capacitive loads exceeding the datasheet's drive specification. This page synthesizes current distributor pricing, drop-in same-package and cross-brand alternatives from verified cross-reference data, and practical design notes not found in the bare manufacturer datasheet - giving an engineer a single, structured view for sourcing and second-sourcing decisions.

見積もり お問い合わせ
TLE6212XUMA1 - ABS/TC/ESC Sensor Interface IC | Infineon
TLE6212XUMA1

TLE6212XUMA1 - ABS/TC/ESC Sensor Interface IC | Infineon

The Infineon Technologies TLE6212XUMA1 is an automotive ABS, traction-control, and electronic-stability-control sensor interface IC with voltage input and voltage output functions, supplied in a 64-pin PG-LQFP package. The verified source data identifies it as an IC SENSOR FOR ABS/TC/ESC device and places it in the sensor and detector interface category. A sensor interface IC is an integrated circuit that connects physical or resistive sensing elements to an automotive control unit. In this product class, the interface device conditions sensor-related signals and supports communication between sensors and a controller. The TLE6212XUMA1 is associated with ABS, TC, and ESC systems, where accurate wheel-speed sensing is important for braking, traction, and vehicle stability control. Its voltage-input and voltage-output classification distinguishes it from purely digital sensor-interface devices. The verified distributor information confirms the device family and package, including the PG-LQFP-64 designation. Detailed electrical limits, internal architecture, supported sensor resistance, diagnostic behavior, supply range, and timing specifications were not included in the supplied verified data and must therefore be confirmed against the manufacturer datasheet before design release. The product is presented here with an explicit separation between verified facts and unavailable technical parameters. Typical automotive uses include ABS wheel-speed sensing, traction-control systems, electronic stability control, and vehicle motion-control electronic control units. The relevant design task is to verify that the selected sensor, wiring, connector, grounding, filtering, and diagnostic strategy all match the device requirements. Automotive production designs should also validate environmental, EMC, functional-safety, and supplier-specific requirements using the manufacturer’s official documentation. The PG-LQFP-64 package requires a PCB footprint, pin-1 orientation, exposed-pad or thermal-land treatment, and assembly process compatible with Infineon’s package drawing and recommended land pattern. Do not infer pin functions from the distributor category text alone; use the official TLE6212 datasheet and package drawing for schematic capture, PCB layout, and production inspection. This page consolidates the verified product identity, distributor availability references, package information, application context, and data gaps for engineering review. It is intended to support component selection and sourcing while avoiding unsupported claims about electrical performance, lifecycle status, pricing, or drop-in alternatives.

見積もり お問い合わせ