集積回路

サブカテゴリ

📁 ADC/DAC 2,700+ 製品 📁 アンプIC 1,100+ 製品 📁 オーディオコーデック 18 製品 📁 オーディオIC 2 製品 📁 クロック＆タイミング 480+ 製品 📁 Comparator ICs 0 製品 📁 DSP 1,000+ 製品 📁 データ収集IC 2 製品 📁 デジタルポテンショメータ 4 製品 📁 ディスプレイドライバ＆コントローラ 1 製品 📁 FPGA & CPLD 6,800+ 製品 📁 インターフェースIC 2,300+ 製品 📁 LEDドライバ 1 製品 📁 ロジックIC 360+ 製品 📁 メモリIC 870+ 製品 📁 マイクロコントローラ 19,000+ 製品 📁 マイクロプロセッサ 4 製品 📁 モータドライバ 1 製品 📁 その他 1 製品 📁 Sensor and Detector Interfaces 1 製品 📁 専用IC 15 製品 📁 ビデオIC 13 製品

製品 (35,000+)

THS6182DR - Low-Power ADSL/PLC Differential Driver | TI (Tape & Reel)
THS6182DR

THS6182DR - Low-Power ADSL/PLC Differential Driver | TI (Tape & Reel)

The Texas Instruments THS6182DR is a low-power current-feedback differential line driver designed for full-rate ADSL and power-line communication systems. It delivers a 44 Vpp differential output swing, operates from dual supply rails, and is offered in a 16-pin SOIC package. The device includes selectable full, mid, low, and shutdown bias modes to balance output drive against power consumption. A line driver is an analog output interface that converts upstream signal information into a high-voltage differential signal capable of traversing copper, telephone, or other communications lines. The THS6182 belongs to the current-feedback operational-amplifier family and is positioned between a communications signal source and the physical line. Its differential architecture reduces susceptibility to common-mode noise while providing the voltage swing and current-drive capability needed by xDSL line cards. Key features include 11 mA per channel in full-bias mode, 7.5 mA per channel in mid-bias mode, 4 mA per channel in low-bias mode, and 0.25 mA per channel in shutdown mode. The manufacturer identifies low distortion, low inverting current noise, and stable operation at low channel current as important benefits for receiver sensitivity and central-office line-card density. An IADJ pin also provides user-controlled bias current for system-level optimization. According to the manufacturer product page, the THS6182 is pin compatible with EL1503C and EL1508C line-driver families and is available in multiple packages and power-control modes. Its current-feedback differential architecture is intended to preserve signal integrity while minimizing dissipation, making it particularly relevant to high-density ADSL central-office equipment and PLC systems. The advertised 3.2 nV/√Hz inverting current noise supports receiver-sensitive signal paths. Typical deployments include full-rate ADSL central-office line cards, DSL access multiplexor equipment, remote terminal equipment, and PLC transmitters. In these systems, the driver accepts an upstream differential signal and produces a substantially larger differential output across the line interface. Designers must preserve the intended differential topology, provide suitable bypass capacitance, terminate unused inputs correctly, and verify thermal performance across the required line swing and channel-current range. A key design consideration is power mode selection. Full-bias mode provides maximum drive when required, while mid- and low-bias modes reduce dissipation when channel current and reach requirements permit. The shutdown state provides the lowest listed current, but enabling and disabling channels must be coordinated with the communication protocol to avoid invalid transmitted states. This page combines verified manufacturer and distributor information with application guidance; it does not infer unprovided electrical limits or invent replacement parts.

見積もり お問い合わせ
THS7314D - 3-Channel SDTV Video Amplifier | Texas Instruments
THS7314D

THS7314D - 3-Channel SDTV Video Amplifier | Texas Instruments

The Texas Instruments THS7314D is a 3-channel SDTV video amplifier with integrated fifth-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and combines three video channels in one package. According to the Texas Instruments product and data-sheet information, the device uses the Silicon-Germanium BiCom-III process and consumes 16 mA total quiescent current at 3.3 V. A video amplifier is an analog signal-chain component that conditions composite or component video signals between a source, processing stage, and display. It belongs to the amplifier hierarchy, specifically the video-amplifier and video-buffer category. Unlike a passive termination network, an integrated video amplifier can provide filtering, gain, impedance matching, and output-drive capability while reducing the number of discrete components required on a video board. The THS7314D provides three buffered channels, 6 dB gain, and fifth-order filtering in one 8-pin SOIC. Its rail-to-rail output stage supports both AC and DC line-driving requirements. The manufacturer specifically identifies driving two lines or 75-ohm loads as supported use cases, making the device relevant to SDTV routing, video distribution, and display-adapter designs. The integrated filter function is especially useful when system designers want repeatable channel filtering without external filter networks. Its low-power operation distinguishes the part from higher-current video drivers. Texas Instruments states that the total 16 mA quiescent current at a 3.3 V supply makes the THS7314 suitable for USB-powered, portable, and other power-sensitive video applications. The single-supply 3 V to 5 V operating range also allows the same architecture to operate from nominal 3.3 V and 5 V system rails, although the complete design must satisfy the limits in the manufacturer data sheet for each voltage and temperature condition. Typical applications include SDTV output buffering, video splitters and distribution boards, portable media equipment, video capture equipment, and display interfaces. In each case, the three-channel structure reduces routing complexity while the fifth-order filters and 6 dB gain support controlled signal transmission into downstream analog video stages. The 75-ohm drive capability is useful when the output must connect through conventional video cabling to a terminated load. Designers should verify the complete pin configuration, decoupling requirements, input and output impedance, bandwidth, channel-to-channel behavior, and recommended termination network against the official data sheet. Video-layout practices should also be considered, including short trace routing, careful grounding, separation between analog video paths and noisy switching circuitry, and appropriate filtering at external connectors. This page consolidates the verified manufacturer and distributor information for THS7314D and clearly identifies parameters for which verified values were not supplied. It also distinguishes the confirmed device characteristics from engineering information that must be obtained from the official THS7314 data sheet before layout or qualification decisions are finalized.

見積もり お問い合わせ
THS7315D - 3-Channel SDTV Video Amplifier | Texas Instruments
THS7315D

THS7315D - 3-Channel SDTV Video Amplifier | Texas Instruments

Texas Instruments THS7315D is a three-channel SDTV video amplifier with integrated fifth-order filters and 5.2 V/V gain, operating from a single 3 V to 5 V supply in an 8-SOIC package. The device combines three video channels, fixed 5.2 V/V gain, and fifth-order filtering for CVBS, S-Video, YPBPR 480i/576i, YUV, and GBR/RGB signal paths. A video amplifier is an analog signal-conditioning IC that increases the amplitude of composite or component video signals while controlling bandwidth, attenuation, and unwanted spectral content. Within the broader semiconductor hierarchy, the THS7315D is a video amplifier, a type of analog amplifier, and ultimately an integrated circuit used within display, broadcast, set-top-box, and video-conversion systems. The THS7315D integrates three independent SDTV video amplifier channels and fifth-order filters into one package. Its fixed gain of 5.2 V/V is useful when a source produces a relatively small video amplitude and the downstream circuitry requires additional signal swing. The fifth-order filters provide frequency-dependent noise and interference attenuation, while the single-supply architecture simplifies power planning in 3 V and 5 V systems. Texas Instruments fabricated the device using its complementary silicon-germanium BiCom3 process. This integration reduces the number of discrete amplification and filtering stages required in a multi-channel analog video path. Because the amplifier includes filters rather than functioning only as a wideband buffer, board-level signal integrity depends on correct source and load impedances, adequate bypass capacitance, short output routing, and proper grounding. The supplied data does not provide detailed output impedance, bandwidth, settling-time, noise, or stability-versus-capacitance figures, so those characteristics must be confirmed in the manufacturer datasheet before final circuit sign-off. Typical uses include SDTV video buffering, Y/Cb/Cr component-video distribution, CVBS and S-Video processing, RGB amplification, and DAC reconstruction filtering. The integrated three-channel arrangement is particularly useful when red, green, and blue or Y, Pb, and Pr channels must receive matched amplification and filtering. It can also support protected or industrial video equipment where reducing the number of active stages simplifies signal routing and maintenance. A primary design consideration is ensuring that the source impedance, termination, and downstream load remain compatible with the integrated filter network. The manufacturer's datasheet and typical application information should be used to select input and output coupling or termination components. PCB layout should keep the device and its bypass capacitors close together, maintain short analog traces, provide an uninterrupted ground reference, and isolate sensitive video paths from switching and high-current return paths. This product page consolidates the verified manufacturer and distributor information, distinguishes documented THS7315D characteristics from missing technical data, identifies verified same-package replacements, and adds practical application and layout guidance for engineers evaluating the THS7315D in SDTV video signal chains.

見積もり お問い合わせ
THS7316D - 3-Channel HDTV Video Amplifier | Texas Instruments
THS7316D

THS7316D - 3-Channel HDTV Video Amplifier | Texas Instruments

Texas Instruments THS7316D is a 3-channel HDTV video amplifier with integrated 5th-order filters and 6 dB gain, supplied in an 8-pin SOIC package. It operates from a single 3 V to 5 V supply and provides three buffered video channels for HDTV and related video-signal processing systems. The device is fabricated using the Silicon-Germanium (SiGe) BiCom-III process and is designed for low-power video applications where integrated filtering reduces external circuit complexity. A video amplifier is a specialized analog amplifier that buffers and conditions composite or component video signals while preserving usable bandwidth and signal amplitude. The THS7316 belongs to the broader video-amplifier and signal-conditioning category, integrating three amplifier channels with fixed filtering into one device. This makes it useful in set-top boxes, television equipment, video processors, projectors, displays, and other systems that distribute or convert analog video signals. The principal features of the THS7316D are its three-channel architecture, 6 dB voltage gain, 5th-order integrated filters, single-supply operation, and 43 MHz video bandwidth identified in the verified product data. The filter implementation helps remove unwanted high-frequency video components before they reach downstream circuitry. Its three-channel arrangement allows red, green, and blue video paths to be amplified consistently within one package, reducing the number of separate buffer devices required. The device uses a low-power SiGe BiCom-III process and is intended for 3 V to 5 V single-supply systems. The verified distributor description identifies the THS7316 as a 3-channel integrated video buffer, while the Texas Instruments product page identifies the 5th-order filter and 6 dB gain functions. The 8-SOIC package is compatible with conventional surface-mount assembly and is suitable for compact consumer and industrial video equipment. Typical applications include HDTV signal conditioning, RGB video distribution, video projection systems, television receivers, set-top-box video outputs, and industrial video interfaces. The integrated filtering is particularly useful where the source signal requires predictable bandwidth limiting before a display, encoder, scaler, or analog-to-digital conversion stage. The fixed 6 dB gain also provides a defined signal-conditioning function rather than requiring an external gain network for basic video buffering. Designers should verify the complete electrical limits, decoupling requirements, output loading, and filter response in the manufacturer datasheet before layout release. Pay particular attention to the single-supply input range, required bypass capacitors, and the acceptable input and output signal levels. Because the available verified data does not provide the complete pin mapping or all parameter values, the PCB footprint and analog signal path should be checked against the official THS7316 documentation rather than inferred from distributor descriptions. This page combines verified manufacturer and distributor information, source-backed technical context, and practical selection considerations for engineers evaluating the THS7316D. It also distinguishes verified attributes from parameters that remain to be confirmed in the datasheet, helping prevent assumptions about gain, bandwidth, filtering, or pin compatibility during component selection.

見積もり お問い合わせ
THS7375 - 4-Channel SDTV Video Amplifier | Texas Instruments
THS7375

THS7375 - 4-Channel SDTV Video Amplifier | Texas Instruments

The THS7375 is a low-power, single-supply, 3 V to 5 V four-channel integrated video buffer from Texas Instruments, fabricated using the complementary Silicon-Germanium (SiGe) BiCom3X process. It is available in a lead-free and green (RoHS) compliant TSSOP-14 package. The device incorporates a sixth-order Butterworth filter that can be bypassed, making it useful as a digital-to-analog converter (DAC) reconstruction filter. With a rail-to-rail output stage and a fixed gain of 5.6 V/V (15 dB), the THS7375 is designed for SDTV video applications, providing excellent image quality and driving capability for both AC and DC coupled loads. A video amplifier is an electronic amplifier that processes video signals, typically providing gain, buffering, and filtering to ensure signal integrity over transmission lines. In the signal chain, the THS7375 sits between a video DAC or encoder and the output connector, performing reconstruction filtering and line driving. It belongs to the category of integrated video buffers, which are essential in consumer electronics, set-top boxes, DVD players, and video surveillance systems. The THS7375's integrated filters eliminate the need for external passive components, simplifying design and reducing board space. Key features include a 6th-order Butterworth filter with a cutoff frequency suitable for SDTV (standard-definition television) signals, a fixed gain of 5.6 V/V, and the ability to drive two lines per channel or 75-ohm loads. The device operates from a single 3 V to 5 V supply, making it compatible with common digital logic levels. The rail-to-rail output stage ensures maximum output swing, and the low power consumption makes it ideal for battery-powered or power-sensitive applications. Technically, the THS7375 uses the BiCom3X process, which combines bipolar and CMOS transistors on a silicon-germanium substrate, offering high-speed performance with low power. The integrated filter is a 6th-order Butterworth type, providing a flat passband and sharp roll-off to remove out-of-band noise and aliasing artifacts. The device also features an internal gain of 5.6 V/V, which is optimized for driving video loads with proper termination. Typical applications include video buffer and line driver for SDTV signals in set-top boxes, DVD players, video recorders, and surveillance systems. It is also suitable for driving video signals from DaVinci processors and other video encoders. The THS7375's ability to drive two lines per channel allows for flexible routing in complex video distribution systems. When designing with the THS7375, ensure proper power supply decoupling with a 0.1 uF ceramic capacitor close to the VCC pin. The input should be AC-coupled if the source has a DC offset, and the output should be terminated with 75-ohm resistors to match the characteristic impedance of the cable. The filter bypass pin can be used to disable the internal filter if external filtering is preferred.

見積もり お問い合わせ
THS788PFD - 200 MHz Quad-Channel 13 ps TMU | Texas Instruments
THS788PFD

THS788PFD - 200 MHz Quad-Channel 13 ps TMU | Texas Instruments

The Texas Instruments THS788PFD is a four-channel time measurement unit (TMU) using time-to-digital converter architecture, with 8 ps single-shot accuracy, 13 ps resolution derived from an external 200 MHz controller clock, and a measurement result range of 7 s in a 100-pin HTQFP package. It supports a 200 MHz event-input rate and provides LVDS-compatible event inputs, an LVDS result interface, four event channels, and a synchronization channel. A time measurement unit is a specialized clock-and-timing semiconductor that converts the elapsed time between events into a digital result. The THS788 belongs to the TMU hierarchy, where its TDC architecture combines fine timing resolution with high-rate event capture. This makes it suitable for systems requiring precise timing rather than ordinary counting, including synchronized instrumentation, pulsed systems, test equipment, and communications or industrial timing subsystems. The key performance feature is 8 ps single-shot accuracy, supported by a 13 ps least-significant-bit resolution. The external controller clock operates at 200 MHz, and the event input rate can reach 200 MHz. The 7 s result range supports substantially longer measurement intervals than the 13 ps conversion resolution alone would imply, depending on the configured measurement sequence and system implementation. LVDS-compatible interfaces provide high-speed, noise-resistant signaling for demanding board environments. Technically, the THS788 uses a fast TDC architecture to perform time measurements across four event channels. Its inputs are designed for LVCMOS or LVDS signaling, while the result output is identified as LVDS. The synchronized architecture and dedicated sync channel make the device suitable for multi-event acquisition where repeatable timing relationships matter. The stated low temperature coefficient of 0.1 ps/°C indicates attention to timing stability over temperature. Typical applications include high-speed test and measurement systems, pulsed-signal analysis, synchronization of multiple timing events, industrial automation requiring deterministic event capture, and communications equipment that must measure narrow time intervals. The device can also support scientific instrumentation where event timing accuracy directly affects the quality of the collected result. Designers should treat the external 200 MHz clock, LVDS-compatible input routing, result interface, decoupling, and high-speed return paths as an integrated signal-integrity problem. Input timing, trace length, termination, and controller configuration must be evaluated together because the 13 ps resolution does not guarantee end-to-end system accuracy without clean clocking, controlled stimulus, and correct interface implementation. This page combines the verified manufacturer and distributor information for the THS788PFD with practical selection guidance, application analysis, pricing references, and an honest assessment of available drop-in alternatives.

見積もり お問い合わせ
THS789PFD - Quad-Channel 200MHz Time Measurement IC | TI
THS789PFD

THS789PFD - Quad-Channel 200MHz Time Measurement IC | TI

Texas Instruments THS789PFD is a quad-channel time measurement unit (TMU) with a 200 MHz measurement clock, one output, and a 100-pin HTQFP package measuring 14 mm by 14 mm. The device is listed for commercial-grade operation from 0 °C to 70 °C and is supplied in a tray. Its verified product identity also includes an exposed thermal pad and surface-mount construction. A time measurement unit is a specialized clock-and-timing semiconductor that measures elapsed time by comparing reference events. A multi-channel TMU extends this function across several independent measurement paths, making it useful when a system must acquire timing relationships, delays, pulse widths, or event intervals without implementing each measurement function as discrete logic. The THS789 therefore belongs to the clock-and-timing IC category and the broader application-specific timing semiconductor hierarchy. The principal verified specifications are four measurement channels, a 200 MHz timing reference, and one output. The 200 MHz reference corresponds to a 5 ns reference period, while the quad-channel architecture permits parallel timing observations. The 100-pin HTQFP package provides numerous external connections for timing inputs, control, power, and outputs, while the exposed pad supports heat transfer from the device to the PCB. The THS789PFD is specifically identified as a Time Measurement IC and is marketed by DigiKey under the Application Specific Clock/Timing classification. This distinguishes it from conventional general-purpose timers by emphasizing precision event-interval measurement across four channels. The exact input voltage range, minimum measurable interval, timing accuracy, propagation delay, output characteristics, and power specifications are not included in the supplied verified excerpts and should be taken from the complete manufacturer datasheet before design release. Typical engineering uses include industrial automation equipment, communications timing analysis, instrumentation, automated test systems, and embedded systems that compare multiple event arrivals. The 100-pin package and exposed pad make careful PCB layout, grounding, and thermal management important. In multi-channel systems, signal integrity at the timing inputs can materially affect measurement consistency, so controlled impedance, short return paths, and clean reference distribution should be prioritized. A principal design trade-off is package size versus channel density: the 14 mm by 14 mm HTQFP offers extensive connectivity for four timing channels but requires more PCB area than a compact mixed-signal package. Engineers should also confirm the complete electrical limits and interface timing before substituting another device or extending the operating temperature beyond the verified 0 °C to 70 °C range. This product record combines verified manufacturer and distributor identity, package and ordering information, commercial availability, and explicit engineering guidance for evaluating the THS789PFD. It also distinguishes confirmed facts from parameters that still require review in the full Texas Instruments datasheet, supporting faster procurement and design planning without treating unverified specifications as guaranteed.

見積もり お問い合わせ
THVD1400DR - 3.3-5V RS-485 Transceiver, 500Kbps, 8-SOIC | Texas Instruments
THVD1400DR

THVD1400DR - 3.3-5V RS-485 Transceiver, 500Kbps, 8-SOIC | Texas Instruments

The Texas Instruments THVD1400DR is a 3.3-V to 5-V RS-485/RS-422 half-duplex transceiver in an 8-pin SOIC package, supporting data rates up to 500 kbps with integrated ±12-kV IEC ESD (HBM) protection on the bus pins. The part contains one driver and one receiver on a single die, operates from a 3.0 V to 5.5 V supply, and meets or exceeds the requirements of the TIA/EIA-485A standard for robust industrial communication. The wide common-mode voltage range and low input leakage on bus pins make the device suitable for multi-point applications over long cable runs. What is an RS-485 transceiver? An RS-485 transceiver is a type of differential line driver/receiver interface IC that converts a single-ended TTL/CMOS logic signal into a balanced differential signal on a twisted-pair bus, and vice versa. RS-485 belongs to the broader TIA/EIA-485 family of serial interface standards and is widely used in industrial automation, building control, and long-distance communication. The transceiver sits between a UART/MCU and the physical bus, providing the voltage translation, drive strength, and ESD protection required to survive harsh electrical environments. Key features include 1/8 unit load support (allowing up to 256 nodes on the bus), ±12-kV IEC 61000-4-2 contact discharge ESD protection on bus pins, hot-plug support with glitchless power-up, and an extended industrial operating temperature range of -40 °C to +125 °C. The THVD1400DR also integrates thermal shutdown, current limiting on driver outputs, and receiver fail-safe for open, shorted, or idle bus conditions, eliminating the need for external biasing resistors on many designs. The architecture combines a precision differential line driver with a high-CMRR receiver and on-chip charge-pump-generated drive rails. The wide bus common-mode range of -7 V to +12 V lets the device tolerate ground potential differences between nodes across long cable runs. The 8-pin SOIC footprint provides drop-in compatibility with industry-standard pinout, simplifying PCB reuse and second-sourcing. Typical applications include industrial fieldbus networks (Modbus, Profibus-compatible), HVAC building automation, solar inverter daisy-chains, motor drive control links, smart-grid metering, and any point-to-point or multi-drop RS-485 link requiring IEC-grade ESD robustness. The low quiescent current also makes it suitable for battery-backed or always-on telemetry nodes. When designing with this device, place 100 nF decoupling close to VCC and add a 1 µF bulk capacitor when long supply traces are present. For bus termination, use a 120 Ω resistor across the differential pair at the two end nodes only; intermediate nodes should not be terminated to preserve signal integrity on multi-drop buses.

見積もり お問い合わせ
THVD1450 - 50 Mbps RS-485 Transceiver, ±18 kV ESD | Texas Instruments
THVD1450

THVD1450 - 50 Mbps RS-485 Transceiver, ±18 kV ESD | Texas Instruments

The Texas Instruments THVD1450 is a 3.3-V to 5-V, half-duplex RS-485/RS-422 transceiver with ±18-kV IEC ESD protection, delivering data rates up to 50 Mbps in an 8-pin SOIC (D) package. It belongs to the THVD14xx family of noise-immune transceivers engineered for rugged industrial environments and supports a wide 3 V to 5.5 V supply range with a low-current standby mode for power-constrained designs. An RS-485 transceiver is a physical-layer device that converts a single-ended UART signal into a balanced differential signal for transmission over twisted-pair cabling, enabling robust communication across long distances and electrically noisy industrial settings. The RS-485 standard (TIA/EIA-485) defines a differential bus topology that allows up to 32 unit loads (256 with modern transceivers) on a single twisted pair, with common-mode voltage range of −7 V to +12 V and cable lengths beyond 1200 m at reduced speeds. Transceivers sit at the bottom of the OSI physical layer (PHY) and above the UART/SCI controller, framing all fieldbus, PROFIBUS, Modbus, BACnet, and DMX512 wiring as the dominant industrial multi-drop PHY in use today. Key features of the THVD1450 include ±18-kV IEC 61000-4-2 air-discharge ESD on bus pins (eliminating external TVS arrays), ±8-kV IEC contact discharge, integrated bus fail-safe biasing (open, short, idle), 1.5 V typical differential output swing into 54 Ω, hot-plug support with glitch-free power-up, and an operating junction temperature range of −40 °C to +125 °C. The 8-SOIC package provides a compact 3.9 mm × 4.9 mm footprint, suitable for point-to-point and multi-drop fieldbus links. Architecturally, the THVD1450 integrates a differential line driver, a wide-common-mode differential receiver, internal fail-safe bias resistors, and an IEC-ESD cell at the bus pins. The wide 3 V to 5.5 V supply range allows direct connection to either 3.3-V MCU rails or legacy 5-V logic, simplifying BOM in mixed-voltage industrial nodes. Typical applications include factory-automation fieldbus nodes, building-automation BACnet wiring, solar inverter daisy-chain comms, motor-drive encoder feedback, smart-meter data concentrators, and any noise-immune multi-drop RS-485 link where bus pins face direct human/operator contact and require maximum ESD survivability. The 50-Mbps speed grade also supports high-rate motion-control and vision-system links over short cable. When designing with this part, place 100 nF decoupling within 2 mm of VCC and add a 120 Ω termination resistor at each cable end only. Avoid stubs longer than one-tenth of the driver rise time to prevent reflections at 50 Mbps, and never tie the bus pins to a stub that exceeds the unit-load budget of 32 (or 256 with low-IU parts). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including same-family THVD14xx options, cross-brand pin-compatible RS-485 transceivers, and IEC-ESD design-in guidance for rugged industrial nodes.

見積もり お問い合わせ
THVD1450D - 3.3-5V RS-485 Transceiver ±18kV ESD | TI
THVD1450D

THVD1450D - 3.3-5V RS-485 Transceiver ±18kV ESD | TI

The Texas Instruments THVD1450D is a 3.3-V to 5-V RS-485/RS-422 transceiver housed in an 8-pin SOIC package, featuring integrated IEC 61000-4-2 ±18-kV ESD protection on the bus pins. The device integrates one driver and one receiver (1/1 configuration) in half-duplex mode and supports data rates up to 50 Mbps over a wide 3.0V-5.5V supply range. An RS-485/RS-422 transceiver is a physical-layer interface IC that translates logic-level UART or SPI signals from a microcontroller into the differential voltage signaling required by the RS-485 and RS-422 standards. Differential signaling allows data transmission over long cable runs (up to 1200 m per the RS-485 standard) in electrically noisy industrial environments, because common-mode noise is rejected by the receiver's differential comparator. Within the broader system hierarchy, the transceiver sits between the controller's UART/SPI logic and the physical twisted-pair bus, sitting alongside other power-management and interface ICs on the bus node's BOM. Key features include ±18-kV HBM-equivalent IEC 61000-4-2 ESD protection on the A and B bus pins, ±4-kV IEC 61000-4-4 EFT immunity, a 30-mV receiver hysteresis for noise rejection, and a wide -40°C to +125°C operating temperature range. The wide 3.0V-5.5V supply range makes the part compatible with both 3.3V and 5V MCU rails without level shifters, while the 1/1 half-duplex configuration is the most common building block for daisy-chained or point-to-point RS-485 nodes. The device architecture uses a differential line driver with controlled slew rate to limit EMI, and a differential comparator receiver with 30-mV hysteresis to reject bus noise and reflection-induced ringing. The integrated IEC 61000-4-2 ESD cells on the bus pins (tolerant to ±18 kV contact/air discharge) eliminate the need for external TVS protection in most industrial installations, reducing BOM cost and PCB area. The part is part of TI's THVD14xx family, which shares pinout and feature set across data-rate grades. Typical applications include industrial factory automation, HVAC networks, building-automation RS-485 trunks, motor-control encoder feedback, smart-grid metering, and any embedded system that needs a rugged 3.3V/5V RS-485 node with strong system-level ESD/EFT immunity. When designing with this device, place 100-nF decoupling capacitors as close as possible to the VCC pin and follow RS-485 cable-stub length recommendations. Note that the wide-supply 3.0V-5.5V range allows direct connection to both 3.3V and 5V MCUs, but the bus common-mode voltage must remain within the -7V to +12V range defined by the standard. This page synthesizes distributor stock, drop-in alternatives, and practical design notes that complement the manufacturer datasheet with real BOM-level guidance.

見積もり お問い合わせ
THVD1450DRBR - 3.3-5V RS-485 Transceiver, ±18kV ESD, 50Mbps | TI
THVD1450DRBR

THVD1450DRBR - 3.3-5V RS-485 Transceiver, ±18kV ESD, 50Mbps | TI

The Texas Instruments THVD1450DRBR is a 3.3-V to 5-V RS-485/RS-422 half-duplex transceiver housed in an 8-pin VSON EP (DRB) package measuring 3x3 mm, supporting data rates up to 50 Mbps with integrated ±18-kV IEC 61000-4-2 ESD protection on the bus pins. It operates from a single 3-V to 5.5-V supply and provides one driver and one receiver (1/1) on a shared differential bus pair for two-wire multi-drop topologies. An RS-485/RS-422 transceiver is a physical-layer interface IC that converts between a single-ended UART/logic signal on the controller side and a differential voltage on a twisted-pair cable. Half-duplex operation means the same differential pair is shared between transmit and receive paths, reducing wire count for multi-drop industrial networks such as Modbus RTU, Profibus, and DMX512. Within the broader signal-chain taxonomy, the THVD1450 belongs to the transceiver -> line driver/receiver -> interface IC -> power-tree signal-chain hierarchy used in industrial automation, building automation, and point-of-sale equipment. Key differentiating features include ±18-kV IEC 61000-4-2 contact/air ESD immunity on the bus pins, ±4-kV IEC 61000-4-4 EFT immunity, and a wide 3-V to 5.5-V supply range that allows direct connection to 3.3-V MCUs or 5-V legacy controllers without external level shifters. The integrated fail-safe biasing on the receiver guarantees a known logic-high output when the bus is idle, shorted, or open. The 8-pin VSON EP package with exposed thermal pad occupies only 3x3 mm, suitable for dense fieldbus nodes and compact sensor modules. The architecture uses a differential line driver with controlled slew rate and a differential comparator receiver with 30 mV of hysteresis for noise rejection. The wide common-mode range (typically -7 V to +12 V) tolerates ground-potential differences between nodes on long cable runs, while the 1-unit-load receiver (32 nodes) supports large multi-drop networks within Modbus-style installations. Typical applications include industrial fieldbus networks, motor-drive feedback links, building-automation gateways, solar inverter monitoring, and any cable link requiring IEC-rated ESD/EFT robustness. The bus pins survive ±18-kV contact discharge per IEC 61000-4-2, eliminating external TVS diode arrays in many designs. When designing with this part, place a 100 nF decoupling capacitor close to VCC, respect the DRB exposed-pad layout for thermal spreading, and rely on the internal fail-safe biasing rather than an external resistor network. The wide common-mode range means most cable installations work without additional protection circuitry. This page consolidates distributor pricing, drop-in alternatives in the same 8-VSON footprint, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
THVD1451DRBR - 3.3-5V RS-485 Transceiver, ±18kV ESD | TI
THVD1451DRBR

THVD1451DRBR - 3.3-5V RS-485 Transceiver, ±18kV ESD | TI

The Texas Instruments THVD1451DRBR is a 3.3-V to 5-V RS-485 transceiver housed in an 8-pin VSON (DRB) package with 3x3 mm footprint, featuring ±18-kV IEC 61000-4-2 ESD protection on the bus pins. The device integrates one driver and one receiver (1/1 transceiver), supports half-duplex communication, and operates across a wide 3.0 V to 5.5 V supply range compatible with both 3.3 V and 5 V system rails. An RS-485 transceiver is a physical-layer interface IC that converts differential bus signals to single-ended logic levels, enabling robust half-duplex or full-duplex serial communication over twisted-pair cabling in electrically noisy industrial environments. RS-485 belongs to the broader TIA/EIA-485 standard family of differential transceivers, used as the physical layer for protocols such as Modbus RTU, PROFIBUS, DMX512, and BACnet. The THVD1451 sits within TI's THVD family, which adds integrated IEC ESD protection that eliminates external TVS diodes in many designs. Key features include ±18-kV IEC 61000-4-2 contact discharge ESD protection on the bus pins, ±8-kV IEC 61000-4-2 air-gap discharge, ±4-kV EFT, and ±1.5-kV surge (2 Ω source). The device supports up to 50 Mbps signaling rate, features a low standby current of < 5 µA, and offers 1/8 unit-load fanout supporting up to 256 nodes on a single bus. Thermal and fault protection includes thermal shutdown, current limiting on driver outputs, and bus pin fail-safe biasing that keeps the receiver output in a defined state when the bus is floating. The THVD1451 uses a 3.3 V/5 V CMOS process with precision differential line drivers, achieving low driver skew and rail-to-rail common-mode range from -7 V to +12 V on the bus. The wide common-mode tolerance makes the device tolerant of ground potential differences between nodes in long-cable runs, a defining requirement of the RS-485 standard. The integrated IEC 61000-4-2 ESD protection reduces board area and BOM cost by replacing discrete TVS arrays. Typical applications include factory automation PLCs, building automation HVAC controllers, solar inverter communication gateways, smart-grid metering, and motor drive encoder feedback links. The wide supply and common-mode ranges also support battery management system (BMS) daisy-chained monitoring where nodes see different ground references. Design tip: place the THVD1451 as close as possible to the bus connector with a solid ground pour beneath the exposed pad to maximize ESD dissipation. For full ±18-kV IEC contact discharge protection the PCB ground must be low-impedance; a stitching capacitance of 1 nF Y1-rated between bus ground and chassis is recommended. This page synthesizes distributor pricing, drop-in alternatives and design notes not found in the manufacturer datasheet alone, helping engineers select pin-compatible RS-485 ICs with comparable ESD ratings for industrial and factory-automation designs.

見積もり お問い合わせ
THVD1452D - 3.3-5V RS-485 Transceiver, ±18kV IEC ESD | TI
THVD1452D

THVD1452D - 3.3-5V RS-485 Transceiver, ±18kV IEC ESD | TI

The Texas Instruments THVD1452D is a 3.3-V to 5-V RS-485 transceiver with ±18-kV IEC ESD protection, housed in a 14-pin SOIC (D) package. The device integrates one driver and one receiver (1/1) in a full-duplex configuration, supporting data rates suitable for factory automation, motor drive, and industrial process control networks. The wide 3.0-V to 5.5-V supply range allows direct interfacing to 3.3-V MCUs as well as legacy 5-V UARTs without level shifters. An RS-485 transceiver is a differential line driver/receiver IC designed for robust, long-distance, half- or full-duplex serial communication over twisted-pair cabling. RS-485 transceivers belong to the interface IC family within the broader semiconductor hierarchy (interface IC -> communication transceiver -> differential bus transceiver -> semiconductor). They convert single-ended TTL/CMOS logic levels into differential signals compliant with the TIA/EIA-485 standard, enabling multi-drop networks of up to 32 unit loads on a single bus segment with excellent immunity to common-mode noise. Key features of the THVD1452D include ±18-kV IEC 61000-4-2 ESD protection on the bus pins (HBM ±16 kV, contact discharge ±6 kV), a 1/8 unit-load receiver input impedance allowing up to 256 nodes on the bus, true fail-safe biasing on the receiver outputs, and integrated IEC 61000-4-4 EFT protection. The device operates across the industrial -40 °C to +125 °C temperature range and provides thermal shutdown with automatic recovery. The architecture combines a precision differential line driver with a wide-common-mode receiver that detects signals as low as ±200 mV in the presence of ±25 V common-mode voltage. This robust receiver design eliminates the need for external fail-safe resistors and supports reliable operation in electrically noisy industrial environments such as motor inverters and HVAC equipment. Typical applications include factory automation networks, motor drive position feedback, building automation (HVAC, lighting, access control), solar inverter communications, and any point-to-point or multi-drop RS-485 link requiring strong system-level ESD/EFT robustness without external protection components. When designing with the THVD1452D, place the bus pins' decoupling capacitor as close as possible to VCC (pin 13) and route the differential A/B traces as a 100-Ω differential pair with ground reference. Use a 120 Ω resistor across A and B at the cable ends for termination. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

見積もり お問い合わせ
THVD1452DGSR - 3.3-5V RS-485 Transceiver, 50Mbps, ±18kV ESD | TI
THVD1452DGSR

THVD1452DGSR - 3.3-5V RS-485 Transceiver, 50Mbps, ±18kV ESD | TI

The Texas Instruments THVD1452DGSR is a 3.3-V to 5-V RS-485/RS-422 transceiver with integrated ±18-kV IEC ESD protection, packaged in a 10-pin VSSOP (DGS). It supports data rates up to 50 Mbps in half-duplex or full-duplex topologies, with a 3 V to 5.5 V supply range that is compatible with both 3.3-V and 5-V microcontroller I/O rails. The THVD1452 variant provides active-high driver enable (DE) and active-low receiver enable (RE) pins for flexible bus direction control in multidrop RS-485 networks. An RS-485 transceiver is a differential line driver/receiver IC that converts single-ended logic-level signals (UART, SPI, or general-purpose GPIO) into robust differential signaling on twisted-pair cables, enabling reliable communication over long distances (up to 1200 m at lower data rates) in electrically noisy industrial environments. RS-485 belongs to the TIA/EIA-485 family of standards and is one of the most widely used physical layers in industrial automation, building automation, and process-control networks. Key features include ±18-kV IEC 61000-4-2 air-gap ESD on the bus pins (with HBM ESD also exceeding typical RS-485 levels), 1/8 unit-load support for up to 256 nodes on the bus, glitch-free power-up/power-down to avoid bus contention, and wide bus-pin common-mode range that survives ground potential differences between nodes. The device draws a low quiescent current in standby and offers thermal shutdown protection. The 10-pin VSSOP (DGS) package is thermally enhanced and footprint-compatible with the wider THVD14xx family, enabling a single PCB layout to support pin-compatible device variants of different data rates or enable schemes. Architecture is built on a BiCMOS process that combines the high drive strength of bipolar outputs with the low power consumption of CMOS logic, achieving < 1 mA quiescent current when both driver and receiver are disabled. The internal differential driver maintains the TIA/EIA-485-2017 minimum 1.5 V differential output over a 54 Ω load, while the receiver's wide input common-mode range tolerates ground shifts in large bus installations. Typical applications include factory automation networks (Modbus, PROFIBUS), solar inverter communications, HVAC building controls, grid infrastructure metering, and any 3.3-V or 5-V microcontroller needing a robust differential communication port. Industrial 24-V PLC backplanes and motor-drive feedback links also benefit from the part's high noise immunity. When designing with this device, terminate the bus with 120 Ω resistors at both ends (matched to the characteristic impedance of the twisted pair), place 100 nF decoupling capacitors as close as possible to the VCC pin, and use series fail-safe biasing resistors only if the master/slave node count or cable capacitance makes true fail-safe bias impractical. This page synthesizes distributor pricing, parametric comparison against the broader THVD14xx family and pin-compatible competitors (MAX3485, ISL3179, LTC2855 families), and practical layout guidance beyond the manufacturer datasheet.

見積もり お問い合わせ
THVD1452DR - 3.3-5V RS-485 Transceiver, ±18kV ESD, SOIC-14 | TI
THVD1452DR

THVD1452DR - 3.3-5V RS-485 Transceiver, ±18kV ESD, SOIC-14 | TI

The Texas Instruments THVD1452DR is a 3.3-V to 5-V RS-485 transceiver with ±18-kV IEC ESD protection, packaged in a 14-pin SOIC (D) with one driver and one receiver (full-duplex) per channel. It operates from a 3.0 V to 5.5 V supply, supports data rates up to 50 Mbps, and offers ±18 kV IEC 61000-4-2 air-gap ESD and ±8 kV IEC contact discharge on the bus pins. The device is specified over the -40°C to +125°C industrial temperature range and supports up to 256 bus nodes. An RS-485 transceiver is a differential line driver/receiver that converts a single-ended TTL/CMOS logic signal into a balanced differential signal on a twisted-pair bus, and vice versa. RS-485 is the de-facto physical layer for industrial multi-drop communication (e.g., Modbus, PROFIBUS, DMX512, BACnet), valued for its robustness, long cable reach (up to 1200 m at lower speeds), and noise immunity. The THVD1452 family belongs to TI's THVD14xx portfolio of 3.3-V/5-V dual-supply transceivers, sitting within the broader Interface IC hierarchy: line transceiver -> RS-485 transceiver -> differential interface IC -> semiconductor. Key features of the THVD1452DR include 1/8 unit load (allowing up to 256 devices on the bus), true fail-safe biasing that guarantees a known receiver output when the bus is idle/shorted/open, hot-swap glitch-free bus pins, a wide common-mode range of -7 V to +12 V, and a low quiescent current. Integrated ±18-kV IEC 61000-4-2 ESD eliminates external TVS diodes in many designs, reducing BOM cost and board area for industrial nodes. The transceiver uses a fully balanced differential architecture with slew-rate-limited driver outputs to reduce EMI. An internal common-mode voltage reference and fail-safe resistors on A/B ensure deterministic receiver output regardless of bus state, while the 1/8 unit-load input impedance allows large multi-drop networks without exceeding the RS-485 32-unit-load minimum. The wide 3.0-5.5 V supply range means the same part can be powered from 3.3-V MCUs or 5-V legacy controllers without level shifters. Typical applications include factory-automation fieldbus nodes (Modbus RTU, PROFIBUS), building-automation BACnet MS/TP segments, solar inverter daisy-chains, smart-meter AMI networks, motor-drive encoder links, and any industrial I/O link requiring IEC-level ESD immunity. Designers also use it in DMX512 stage-lighting nodes and HVAC damper-actuator networks. When laying out the THVD1452DR, route the differential A/B pair as a 100-Ω matched impedance, keep the bus stub length below one-tenth of the driver rise time, and place a 100 nF decoupling cap close to VCC. Although the part integrates ±18-kV IEC ESD, a small common-mode choke and a 100 Ω series resistor on each bus pin add extra margin in harsh electrical environments and reduce radiated emissions.

見積もり お問い合わせ
THVD1510DR - 5V RS-485 Transceiver, ±18kV ESD, SOIC-8 | Texas Instruments
THVD1510DR

THVD1510DR - 5V RS-485 Transceiver, ±18kV ESD, SOIC-8 | Texas Instruments

The Texas Instruments THVD1510DR is a 5V RS-485/RS-422 half-duplex transceiver housed in an 8-pin SOIC package with integrated ±18kV IEC 61000-4-2 ESD protection on the bus pins. It delivers up to 10 Mbps signaling, 1 driver and 1 receiver per channel (1/1 configuration), and operates from a single 4.5V to 5.5V supply drawing a typical quiescent current of under 1 mA. The DR suffix designates the small-outline (SOIC-8) tape-and-reel packaging option. An RS-485 transceiver is a differential line driver/receiver IC that enables robust half-duplex or full-duplex serial communication over twisted-pair copper media. RS-485 belongs to the TIA/EIA-485 standard family of balanced digital interfaces used in industrial fieldbus, building automation, motor control, and remote sensor backbones. As a physical-layer interface IC (PHY-LVL interface), it sits between an application MCU's UART and the physical twisted-pair bus, providing the voltage-level translation, common-mode range, and noise immunity that UART logic alone cannot deliver over long distances. Key features include ±18kV IEC ESD on bus pins (HBM 16kV on A/B), ±70V fault tolerance, an extended common-mode range of ±25V, true fail-safe receiver topology, and 1/8 unit-load support allowing up to 256 nodes on a single bus. The half-duplex architecture integrates a single differential driver and a single differential receiver sharing one bus pair (A/Y, B/Z), minimizing board area. Industrial operating temperature spans -40C to +125C, supporting outdoor and factory-floor deployment. The THVD1510 uses a charge-pump-assisted driver architecture to drive the bus with 5V signaling independent of supply voltage. The receiver's true fail-safe topology guarantees a logic-high output when the bus is shorted, open, or idle, eliminating the need for external bias resistors. Internal hot-plug protection prevents inrush current during board insertion into energized backplanes. Typical applications include industrial fieldbus nodes (Modbus RTU, Profibus DP, BACnet MS/TP), solar inverter string monitoring, EV charging station communication, smart-meter AMI concentrators, HVAC controllers, motor-drive CAN-bridge interfaces, and any point-to-point or multipoint RS-485 link operating up to 10 Mbps. The wide common-mode range and ±18kV ESD rating simplify design for IEC 61000-4-2 compliant installations. When designing with this part, verify that cable stub length stays below recommended budgets at 10 Mbps to avoid reflections, and provide a 100 nF decoupling capacitor within 5 mm of VCC. For 256-node configurations, ensure total bus capacitance does not exceed the unit-load budget. The fail-safe receiver eliminates external bias resistors. This page synthesizes distributor pricing, drop-in alternatives including same-family THVD15xx members and cross-brand equivalents, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
THVD1550 - 5V RS-485 Transceiver, 50Mbps, ±18kV IEC ESD | TI
THVD1550

THVD1550 - 5V RS-485 Transceiver, 50Mbps, ±18kV IEC ESD | TI

The Texas Instruments THVD1550 is a 5-V half-duplex RS-485 transceiver with integrated ±18-kV IEC 61000-4-2 contact ESD protection, packaged in an 8-pin SOIC (SOIC-8 / D package). It supports data rates up to 50 Mbps and is designed for noise-immune operation in rugged industrial environments. An RS-485 transceiver is a bus-interface IC that converts a single-ended UART/logic signal into a differential signal on a twisted-pair cable, enabling robust multi-drop communication over long distances. Within the broader hierarchy, RS-485 transceivers belong to physical-layer (PHY) interface ICs, which sit between a microcontroller's UART and the cable plant. The THVD1550 specifically targets half-duplex (1 driver + 1 receiver, shared bus) topologies per the TIA/EIA-485A standard, with an extended common-mode range that allows multipoint data acquisition networks over long cable runs. Key features include a wide 3.0 V to 5.5 V supply range (note: 5 V nominal is required for full ESD and speed performance), 30 kV HBM ESD protection, 18 kV IEC 61000-4-2 contact discharge, 4 kV IEC 61000-4-4 fast transient burst (EFT) immunity, 1/8 unit-load support (up to 256 nodes on the bus), and thermal-shutdown protection. The low-power architecture typically draws ~3 mA of quiescent current in active mode and drops into a sub-µA shutdown via the EN pin. Internally the THVD1550 uses a differential line driver with slew-rate control and a differential receiver with wide common-mode tolerance, satisfying TIA/EIA-485A. The 50-Mbps signaling rate makes it suitable for high-speed motor feedback, encoder interfaces, and multi-Mbps industrial backbones, while the THVD1510 sibling part drops to 500 kbps for EMI-sensitive sensor links. Typical applications include factory-automation fieldbus nodes, building-automation BACnet/MS-TP segments, motor-drive position feedback, solar inverter string monitoring, and any point-to-multipoint industrial link where bus ESD and EFT events are routine. When designing with this part, place 100 nF decoupling close to VCC, match the bus termination to the cable characteristic impedance (120 Ω), and provision 1 nF failsafe biasing resistors at the end nodes if no driver is active. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

見積もり お問い合わせ
THVD1552D - 5V RS-485 Transceiver, ±18kV IEC ESD, 50Mbps | TI
THVD1552D

THVD1552D - 5V RS-485 Transceiver, ±18kV IEC ESD, 50Mbps | TI

The Texas Instruments THVD1552D is a 5V RS-485/RS-422 transceiver with ±18kV IEC ESD protection on the bus pins, supporting data rates up to 50 Mbps in a 14-pin SOIC (D) package. It integrates one driver and one receiver (1/1) in a full-duplex configuration, operating from a single 4.5V to 5.5V supply with a typical quiescent current of approximately 4 mA. A RS-485 transceiver is a physical-layer interface IC that converts the differential logic levels of a UART or controller into the balanced, half-duplex signaling required by the TIA/EIA-485-A standard. As a member of the RS-485/RS-422 interface IC family within the broader interface IC category and signal conditioning/isolation hierarchy, it enables robust multi-drop communication over twisted-pair cable in electrically noisy industrial environments. The THVD15xx family specifically targets rugged industrial applications where IEC-level surge, fast transient, and ESD events would otherwise require external protection components. Key features include ±18kV IEC 61000-4-2 ESD protection on bus pins, ±2kV IEC 61000-4-4 EFT immunity, a wide common-mode range of -7V to +12V allowing up to 256 nodes on the bus, and thermal shutdown with short-circuit protection on the driver outputs. The receiver failsafe design guarantees a known logic-high output when the bus is open, shorted, or idle, eliminating the need for external biasing resistors. Internally, the THVD1552D uses a differential line driver with slew-rate control suitable for 50 Mbps signaling, paired with a differential comparator receiver with 50 mV typical input hysteresis. The half-duplex architecture shares bus pins between driver and receiver, and the full-duplex variant (THVD1552) provides separate driver output and receiver input pins. Typical applications include industrial fieldbus networks (Modbus, PROFIBUS), motor drive encoder links, building automation (BACnet, KNX), solar inverter daisy-chain communications, and any point-to-point or multi-drop RS-485 link requiring IEC-level robustness. Designers typically pair it with a TVS diode array on the bus for additional surge immunity. When designing with this device, place 100 nF decoupling capacitors as close as possible to the VCC pin and add a 1 µF bulk capacitor on the bus-side supply rail. The exposed pad must be soldered to a continuous ground plane for thermal dissipation. Maintain 100 Ω termination at both cable ends to suppress reflections at 50 Mbps. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
THVD1552DGS - 5V RS-485 Transceiver, ±18kV IEC ESD | TI
THVD1552DGS

THVD1552DGS - 5V RS-485 Transceiver, ±18kV IEC ESD | TI

The Texas Instruments THVD1552DGS is a 5-V RS-485 transceiver with integrated ±18-kV IEC 61000-4-2 ESD protection, delivered in a 10-pin VSSOP (DGS) package with extended −40 °C to +125 °C industrial temperature support. It provides one driver and one receiver (1/1) for full-duplex RS-422/RS-485 communication at signaling rates up to 50 Mbps, suiting both multi-drop industrial backbones and high-speed point-to-point links. Background: an RS-485 transceiver is a physical-layer interface IC that translates a low-voltage differential logic signal on a UART or SPI controller side to the rugged, balanced differential bus levels defined by the TIA/EIA-485A standard. By sitting between the application MCU and the twisted-pair cable, it provides the bus biasing, line driving strength, and ESD/EFT immunity required for industrial environments where long cable runs pick up motor noise, lightning surges, and hot-plug transients. Key features include a 4.5 V to 5.5 V single-supply operating range, ±30-kV HBM bus-pin ESD (human-body model), ±18-kV IEC 61000-4-2 contact discharge, ±25-kV IEC 61000-4-2 air-gap discharge, and integrated IEC 61000-4-4 EFT immunity that removes the need for external TVS protection on the bus. The receiver failsafe design guarantees a known logic output when the bus is idle, shorted, or open. Architecturally, the THVD1552 uses a differential line driver with slew-rate-limited outputs and a wide-common-mode receiver that meets the TIA/EIA-485A standard, allowing up to 256 transceivers on a single bus when using lower-speed family members (the THVD1552 is optimized for higher speed). The half-/full-duplex variants in the THVD15xx family share the bus-pin ESD cell, simplifying multi-protocol design. Typical applications include factory automation PLC backplanes, motor-drive communication links, solar inverter telemetry, building-automation RS-485 trunks, and any cable runs through noisy industrial cabinets. When designing with this part, place 100 nF decoupling close to VCC and use a 120 Ω termination at the bus ends only. Total bus load (stub length and cable capacitance) limits the maximum signaling rate, so verify cable length against the 50-Mbps data-rate budget. This page synthesizes distributor stock, parametric drops-in, and field-tested design notes not found in the manufacturer datasheet alone.

見積もり お問い合わせ
THVD1552DR - 5V RS-485 Transceiver, ±18kV ESD | 14-SOIC | TI
THVD1552DR

THVD1552DR - 5V RS-485 Transceiver, ±18kV ESD | 14-SOIC | TI

The Texas Instruments THVD1552DR is a 5-V full-duplex RS-485/RS-422 transceiver housed in a 14-pin SOIC (D) package, integrating ±18-kV IEC 61000-4-2 ESD protection on the bus pins. It supports a signaling rate up to 50 Mbps and operates across a wide 3 V to 5.5 V supply range, making it a robust interface for industrial and noisy environments where reliable differential communication is required. An RS-485 transceiver is a physical-layer (PHY) device that converts a single-ended UART/logic signal into a differential signal suitable for transmission over twisted-pair cabling while meeting the TIA/EIA-485 standard. This PHY sits within the broader OSI stack between the controller UART (data-link layer) and the physical medium (cable), under the family name of serial-interface ICs. The THVD1552 belongs to the THVD15xx sub-family of noise-immune TI transceivers, sharing pinouts and feature sets across half- and full-duplex variants. Key features include ±18-kV IEC 61000-4-2 contact/air-discharge ESD protection directly on bus pins (driver output and receiver input), ±4-kV IEC 61000-4-4 EFT immunity, an internal fail-safe biasing on the receiver output for open/short bus conditions, 1/8 unit-load support (up to 256 nodes on a single bus), and a wide -40 °C to +125 °C operating temperature range. The 14-SOIC footprint is industry standard for this class and supports reflow-solder assembly. The THVD1552 uses a CMOS process with integrated TVS-style ESD structures on the bus pins; this allows designers to replace external protection components, BOM cost, and PCB area. Internal fail-safe circuitry guarantees a logic-high receiver output when the bus is idle, shorted, or terminated but undriven — critical for deterministic polling protocols such as Modbus. Typical applications include motor-control feedback links, multi-drop industrial sensor buses, building automation nodes (BACnet/MS-TP, Modbus RTU), solar inverter inter-module communication, and any 3.3-V or 5-V MCU UART-to-RS-485 bridge requiring strong system-level ESD/EFT robustness. When laying out this part, place the bus-side 120 Ω termination as close to the IC bus pins as possible, route the differential pair A/B symmetrically, and keep the bus stub length under one-tenth of the signal rise time (about 30 mm at 50 Mbps) to preserve signal integrity. This page consolidates distributor stock/pricing, drop-in alternative listings, and PCB design notes not found in the TI datasheet alone, accelerating engineer selection for noise-immune RS-485 designs.

見積もり お問い合わせ
TIBPAL16R8-25CFN - 25ns 8-Macrocell Impact PAL, 20-PLCC | TI
TIBPAL16R8-25CFN

TIBPAL16R8-25CFN - 25ns 8-Macrocell Impact PAL, 20-PLCC | TI

The Texas Instruments TIBPAL16R8-25CFN is a high-performance, low-power IMPACT-X PAL (Programmable Array Logic) device from Texas Instruments, delivering 25 ns maximum propagation delay and an 8-macrocell registered architecture in a 20-pin PLCC (9x9 mm) J-leaded package. The device combines Advanced Low-Power Schottky (ALS) technology with titanium-tungsten (Ti-W) fuses, providing 64 product terms, eight D-type registered outputs, and a typical operating frequency of 30 MHz at 5.25 V supply. A PAL (Programmable Array Logic) device is a one-time-programmable (OTP) SPLD that implements custom combinational and registered logic functions through a programmable AND-OR array, preceded by fixed OR gates and fed by user-defined product-term equations. Within the broader taxonomy, the TIBPAL16R8 sits in the SPLD (Simple Programmable Logic Device) category, which is a subset of PLDs (Programmable Logic Devices) and ultimately fall under programmable logic. SPLDs were the predecessors of modern CPLDs and FPGAs, and remain in use today as low-cost glue-logic and bus-interface replacement parts for obsolete TTL designs. Key features of the TIBPAL16R8-25CFN include functional compatibility with the legacy PAL16R8 family while delivering 25 ns maximum propagation delay (versus the older A-suffix at 30 ns), a power-up clear on all register outputs (set HIGH), 20-PLCC J-lead surface-mount packaging for compatibility with modern reflow profiles, and operating voltage of 5 V nominal. Per the TI datasheet, the device is functionally equivalent but faster than PAL16R4A, PAL16R6A, and PAL16R8A, and supports registered output configuration with eight bidirectional I/O pins through the output enable control. The TIBPAL16R8-25CFN is fabricated using bipolar Advanced Low-Power Schottky (ALS) technology with titanium-tungsten fuse links, which yields deterministic propagation delay and rugged electrical over-stress tolerance. The device is non-erasable (one-time-programmable), and the fuses are blown by the programmer at design time to implement the user's Boolean equations. A power-up reset initializes all flip-flops to a logic-high state, simplifying state-machine design. Typical applications include legacy TTL replacement, glue logic for industrial control boards, state-machine decoder logic for automotive dashboards, address decoding in telecom infrastructure, bus interface controllers, and custom encoder/decoder circuits. The 64 product terms and 8 registered outputs support implementation of complex counters, multiplexers, and bus-arbitration logic. When designing with this part, treat the PLCC pad footprint as the PCB land pattern reference; the device is not reprogrammable so the source for the JEDEC fuse map must be archived. Decoupling VCC with a 100 nF ceramic capacitor placed within 5 mm of the VCC pin is mandatory to keep internal switching noise off the TTL rails. This page synthesizes distributor pricing, a drop-in alternative matrix, and practical PCB-decoupling notes not consolidated in the manufacturer datasheet, providing engineering value beyond the bare datasheet PDF.

見積もり お問い合わせ
TIC10024QDCPRQ1 - 24-Input Automotive MSDI w/ SPI | Texas Instruments
TIC10024QDCPRQ1

TIC10024QDCPRQ1 - 24-Input Automotive MSDI w/ SPI | Texas Instruments

The Texas Instruments TIC10024QDCPRQ1 is an automotive-grade 35-V Multiple Switch Detection Interface (MSDI) with SPI, housed in a 38-pin HTSSOP package with exposed thermal pad (DCP). It monitors 24 direct switch inputs (10 configurable for ground- or supply-referenced switches), integrates adjustable wetting current sources per channel, and reports switch state through an SPI-compatible serial port — eliminating up to 24 discrete comparator/MCU GPIOs in a BCM (Body Control Module). A Multiple Switch Detection Interface (MSDI) is a mixed-signal ASSP that bridges mechanical switches (e.g. rocker switches, momentary buttons, limit switches) to a microcontroller in 12-V automotive electrical systems. It belongs to the broader hierarchy: switch interface IC → interface IC → signal conditioning IC → power management / body electronics ASSP → automotive semiconductor. The MSDI provides per-input wetting current to prevent contact oxidation, programmable threshold comparators for switch-closed detection, and serial aggregation of 24 inputs into a few SPI pins — reducing wire harness complexity and MCU pin count. Key features include 35-V absolute maximum load-dump tolerance (12-V nominal), adjustable wetting current per channel, selectable ground- or supply-referenced inputs on 10 channels, integrated input debounce / de-glitch filters, configurable interrupt generation for wake events, low quiescent current sleep mode, and SPI communication up to [DATA_NEEDED: SPI clock rate]. The device operates across -40 °C to +125 °C ambient (AEC-Q100 Grade 1) and includes thermal shutdown protection. The exposed-pad HTSSOP-38 package provides theta_JA suitable for BCM thermal environments. Technically, the TIC10024-Q1 uses a per-channel comparator architecture with current-mode wetting sources driven from a shared internal regulator. The SPI peripheral implements a standard mode-0 protocol with a frame-format error flag and a global wake-up interrupt output. Internal state machine handles input filtering, hysteresis, and wetting-current modulation; channel configuration registers enable per-input current programming and pull-up/pull-down selection. Typical applications include automotive body control modules (BCM) reading 24 switches per chip, gateway/zonal controllers monitoring door/trunk/hood latches, steering-wheel switch matrices, seat-control switch aggregation, and overhead-console button clusters. The 24-input density lets a single MSDI replace multiple 8-/16-channel general-purpose I/O expanders. When designing with this part, ensure the PCB layout accommodates the exposed thermal pad with at least 4 thermal vias to the inner ground plane for AEC-Q100 thermal conformance. The 38-pin HTSSOP package requires careful routing of SPI traces; keep the SCLK/MOSI/MISO bundle length-matched and routed away from VBAT-switching nodes. This page synthesizes distributor pricing (as of 2026-10-11), drop-in same-package alternatives, and practical AEC-Q100 design notes — information not consolidated in the TI datasheet alone.

見積もり お問い合わせ
TIR1000IPWR - Standalone IrDA Encoder/Decoder | TI | 8-TSSOP
TIR1000IPWR

TIR1000IPWR - Standalone IrDA Encoder/Decoder | TI | 8-TSSOP

The Texas Instruments TIR1000IPWR is a standalone IrDA (Infrared Data Association) SIR (Serial Infrared) encoder/decoder IC housed in an 8-pin TSSOP (PW) package and rated for the -40C to +85C industrial temperature range. It encodes and decodes asynchronous UART bit streams into IrDA-compliant 3/16 pulse-modulated optical signals at data rates from 1200 bps up to 115.2 kbps, and operates from a 2.7 V to 5.5 V supply. The TIR1000IPWR is the tape-and-reel (R) packaging variant of the TIR1000IPW die, which is functionally identical to the legacy TIR1000IPWRG4. An IrDA encoder/decoder is a specialized interface IC that sits between a host microcontroller's UART and an external infrared transceiver (typically a PIN photodiode + LED pair). It performs the bit-stuffing and pulse-width modulation required by the IrDA physical layer so the host CPU only sees a transparent serial stream; the broader category belongs to interface ICs in the connectivity hierarchy (interface IC > transceiver > encoder/decoder). Key features include 1200-bps to 115.2-kbps IrDA 1.0 / HPSIR compliance, single 2.7 V to 5.5 V supply, direct UART handshake interface, low-power shutdown mode, and CMOS construction. The TIR1000IPWR adds an infrared port to any standard UART, eliminating the need for bit-banging IR protocols in firmware and offloading real-time pulse-width timing from the host MCU. The architecture uses a baud-rate generator derived from an external 16x clock (typically the UART's reference), a transmit pulse shaper that converts the UART TX bit stream into 3/16-width IR pulses, and a receive decoder that recovers the UART RX stream from the demodulated IR input. Because it is a pure logic encoder (no onboard LED driver), the host must add a discrete IR transceiver module (e.g., a TFDU4100 / HSDL-3201 class device) to drive the optical front end. Typical applications include IrDA ports on PDAs, industrial handhelds, medical data terminals, point-of-sale (POS) equipment, and consumer electronics printers. The wide supply range and 8-pin TSSOP package make it suitable for space-constrained designs that need to retrofit IrDA onto an existing UART. A key design consideration is clock sourcing. The TIR1000IPWR requires a 16x baud-rate reference clock (XCLK), which is normally derived from the host UART's baud-rate generator; if the host baud rate changes, XCLK must be reprogrammed accordingly. The IC does not include the optical transceiver, so a separate IrDA transceiver module must be added externally. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for IrDA encoder/decoder selection.

見積もり お問い合わせ
TJA1021T/20/C - LIN 2.1 Transceiver, 20kBd, 8-SO | NXP
TJA1021T/20/C

TJA1021T/20/C - LIN 2.1 Transceiver, 20kBd, 8-SO | NXP

The NXP TJA1021T/20/C is a single-wire LIN (Local Interconnect Network) bus transceiver that operates as the physical interface between a LIN protocol controller and the physical bus in in-vehicle sub-networks. The /20 variant supports baud rates from 1 kBd up to 20 kBd and is compliant with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602 and ISO 17987-4:2016. It is housed in an 8-pin SO (SOIC-8) surface-mount package and is pin-to-pin compatible with the legacy TJA1020 and NXP MC33662(B) LIN transceivers. What is a LIN transceiver? A LIN transceiver is a physical-layer (PHY) device that translates the low-voltage digital logic signals (TXD/RXD) generated by a microcontroller or LIN controller into the single-wire, dominant/recessive, slew-rate-controlled bus waveform defined by the LIN standard. It handles bus fault protection (short to battery, short to ground, load-dump), ESD protection, thermal shutdown, and wake-up detection via the bus line. The LIN protocol is widely used as a low-cost sub-bus for non-critical automotive body electronics (mirror controls, seat adjusters, door modules, roof consoles), where CAN would be over-spec. Key features of the TJA1021T/20/C include an integrated slew-rate-controlled LIN bus driver that meets the LIN 2.1/SAE J2602 wave-shaping requirements with minimized electromagnetic emissions (EME), improved ESD robustness compared to the TJA1020, a -27 V to +40 V wide bus load-dump protection range, low-power sleep mode with remote wake-up via the LIN pin, and a dedicated TXD dominant time-out to prevent the bus from being permanently driven. Architecturally, the TJA1021T/20/C uses a bipolar high-voltage process for the bus-side driver stage combined with low-voltage CMOS logic on the protocol-side (TXD, RXD, EN, WAKE). The integrated pull-up resistor on the bus line and the internal slope-control feedback loop produce the trapezoidal LIN waveform specified by SAE J2602, eliminating the need for an external diode or waveform-shaping RC network. Built-in fail-safe features include loss-of-bat handling, ground-shift tolerance, and under-voltage reset on VCC. Typical applications include automotive body-control modules, LIN slaves for door/window/seat/steering-column control, HVAC flap motors, mirror adjusters, ambient lighting nodes, and rain/light sensors. Because the part is qualified to the AEC-Q100 automotive reliability standard, it is designed for the harsh electrical environment of a 12 V automotive battery rail, including jump-start and load-dump transients. It also suits industrial LIN sub-buses where the LIN standard provides a simple, robust single-wire alternative to CAN or RS-485. When designing with this device, ensure the master resistor (typically 660 ohms pull-up to VSUP through a diode) and the bus capacitor (typically 220 pF to 1 nF) are correctly sized, and that the LIN node wake-up strategy (local wake via the WAKE pin vs remote wake via the bus) matches the application requirements.

見積もり お問い合わせ