集積回路

サブカテゴリ

📁 ADC/DAC 3,100+ 製品 📁 アンプIC 1,700+ 製品 📁 オーディオコーデック 18 製品 📁 オーディオIC 2 製品 📁 クロック＆タイミング 650+ 製品 📁 Comparator ICs 1 製品 📁 DSP 1,100+ 製品 📁 データ収集IC 2 製品 📁 デジタルポテンショメータ 4 製品 📁 ディスプレイドライバ＆コントローラ 1 製品 📁 FPGA & CPLD 7,100+ 製品 📁 インターフェースIC 3,100+ 製品 📁 LEDドライバ 1 製品 📁 ロジックIC 450+ 製品 📁 メモリIC 870+ 製品 📁 マイクロコントローラ 20,000+ 製品 📁 マイクロプロセッサ 4 製品 📁 モータドライバ 1 製品 📁 その他 1 製品 📁 Sensor and Detector Interfaces 1 製品 📁 専用IC 15 製品 📁 ビデオIC 13 製品

製品 (38,000+)

THS3091D - 235MHz Current-Feedback Op Amp | Texas Instruments
THS3091D

THS3091D - 235MHz Current-Feedback Op Amp | Texas Instruments

Texas Instruments THS3091D is a single, high-voltage, low-distortion current-feedback operational amplifier with a 235 MHz gain-bandwidth product, 7300 V/us slew rate, and operation across a ±5 V to ±15 V supply range. The device is supplied in an 8-pin SOIC package and is intended for applications requiring large, linear output signals, including pin drivers, power-FET drivers, VDSL line drivers, and arbitrary waveform generators. A current-feedback operational amplifier is a voltage-input, current-output amplifier architecture whose closed-loop bandwidth is primarily controlled by the feedback resistor rather than by a single fixed gain-bandwidth product. In the THS3091D, this architecture supports high-speed operation while maintaining low distortion. The result is useful where conventional voltage-feedback amplifiers would require excessive gain, where signal amplitude and slew rate must remain accurate, or where a capacitive load must be driven through a carefully designed feedback network. Key features include a 235 MHz bandwidth, 7300 V/us slew rate, and a high-voltage capability covering ±5 V to ±15 V supplies. The current-feedback topology provides high speed without relying on a voltage-feedback gain-bandwidth relationship of the same form. Its low-distortion characteristic supports signal-chain designs in which waveform fidelity and amplitude linearity are more important than micropower operation or rail-to-rail input/output capability. The THS3091D is optimized for high-voltage, large-signal output stages. Its supply range permits bipolar or split-supply operation when the circuit requires an output centered around ground, while dual positive supplies can also be used when the signal and output are referenced above ground. Because it is a current-feedback device, feedback-resistor selection is central to achieving the intended bandwidth, gain, and stability rather than treating the feedback network as a passive gain-setting detail. Typical uses include semiconductor pin drivers, power-FET gate drivers, VDSL line-driver outputs, high-voltage arbitrary waveform generation, and instrumentation requiring wide-band signal amplification. In each case, the 235 MHz bandwidth and 7300 V/us slew rate provide the speed needed to preserve large-amplitude waveforms, while the low-distortion architecture helps maintain signal fidelity. The 8-pin SOIC package permits conventional surface-mount assembly. Designers should use the manufacturer datasheet for the complete pin assignment, recommended feedback values, output-current capability, input and output range, and stability constraints. The THS3091D is not a rail-to-rail input or output device, so input common-mode and output swing requirements must be checked against the selected supply voltages. Current-feedback amplifiers can be sensitive to feedback-component tolerances, parasitic capacitance, and capacitive loading. This page consolidates the verified THS3091D product data, lifecycle information, source links, and selection guidance. It also distinguishes the SOIC THS3091D from other package or orderable variants and records unavailable electrical details explicitly rather than inferring them from unrelated THS309x-family members.

見積もり お問い合わせ
THS3092D - Dual 160MHz High-Speed Amplifier | Texas Instruments
THS3092D

THS3092D - Dual 160MHz High-Speed Amplifier | Texas Instruments

The Texas Instruments THS3092D is a dual high-voltage, low-distortion, high-speed current-feedback operational amplifier with 160 MHz bandwidth, 5700 V/µs slew rate, and operation from ±5 V to ±15 V, housed in an 8-pin SOIC package. It delivers two amplifiers per package and is designed for large, linear output swings into demanding loads. A current-feedback operational amplifier is a voltage-feedback amplifier variant whose closed-loop bandwidth and stability are shaped primarily by feedback resistance rather than by a fixed gain-setting capacitance. In the signal-chain hierarchy, the THS3092D belongs to the operational-amplifier, analog-amplifier, and broader semiconductor categories. Its current-feedback architecture is useful where high speed, large output voltage, and low distortion must coexist. Key verified characteristics include 160 MHz small-signal bandwidth, 5700 V/µs slew rate, ±5 V to ±15 V supply operation, 14 pA/√Hz noninverting current noise, 17 pA/√Hz inverting current noise, and 2 nV/√Hz voltage noise. The manufacturer datasheet also identifies low-distortion operation suited to high-voltage arbitrary-waveform driver applications. The device uses a dual amplifier configuration to support two independent signal paths or differential drive arrangements. Its current-feedback topology is particularly appropriate for video, communications, test-and-measurement, and power-driver interfaces where large output swings and fast transient response are required. Designers should still verify gain-bandwidth behavior, load capacitance, output-current limits, and stability for the selected feedback network. Typical applications include high-voltage arbitrary waveform generation, power FET and VDSL line driving, video-signal conditioning, instrumentation, and industrial control interfaces. The broad supply range permits operation from ±5 V through ±15 V, while the high-speed characteristics support fast edge rates and low-distortion signal transfer. A key design consideration is feedback-resistor selection. Because current-feedback amplifiers depend on the feedback impedance, use the manufacturer-recommended values and check the complete gain, bandwidth, and stability relationship for the target load. Decoupling, grounding, and output-stage protection also become important when driving capacitive or high-resistance loads. This page combines verified manufacturer and distributor information, practical application guidance, and explicit design trade-offs for engineers evaluating the THS3092D. It is intended to support component selection, circuit planning, and datasheet-driven review rather than replace the manufacturer datasheet.

見積もり お問い合わせ
THS3095D - High-Speed Current-Feedback Amplifier | Texas Instruments
THS3095D

THS3095D - High-Speed Current-Feedback Amplifier | Texas Instruments

Texas Instruments THS3095D is a single high-voltage, low-distortion, high-speed current-feedback operational amplifier with power-down capability, supplied in an 8-pin SOIC package. The device operates from ±5 V to ±16 V, supports a 6000 V/µs slew rate, and can deliver 310 mA output current. Its low-distortion architecture is intended for large, linear output signals and high-speed waveform applications. The THS3095D includes a power-down pin, PD, that places the amplifier in a low-power standby state and reduces quiescent current from 9.5 mA to 500 µA. The current-feedback operational amplifier is a voltage-feedback amplifier subtype optimized for high-speed signal chains where gain bandwidth and stability can be affected by feedback impedance. Unlike a conventional voltage-feedback amplifier, the THS3095D uses a current-feedback topology that supports high slew rate, broad bandwidth, and low distortion when driven with suitable feedback resistors. It is used where signals must be amplified with high amplitude and fidelity, including pin drivers, power-FET drivers, and arbitrary-waveform generators. Key features include a ±5 V to ±16 V supply range, 6000 V/µs slew rate, 310 mA output-current capability, and a dedicated power-down function. The power-down control can simplify power management in systems that need to disable the amplifier between active intervals. The wide supply range allows operation from split analog rails in communications, instrumentation, industrial, and test equipment. For high-voltage output applications, the THS3095D is designed to preserve signal quality while driving demanding loads. Its low-distortion current-feedback architecture is particularly useful for large-signal waveform generation, where slew rate and output-current capability determine how faithfully large voltage steps can be reproduced. The device is not intended as a general-purpose precision-voltage-feedback amplifier; design calculations should use the manufacturer data sheet for feedback-resistor selection and stability verification. Typical applications include arbitrary-waveform generators, pin and power-FET drivers, VDSL line-driver circuits, communication equipment, and high-speed instrumentation. The amplifier can be used where a high-voltage output swing and rapid transient response are more important than very low offset voltage. The 8-pin SOIC package makes the THS3095D suitable for conventional surface-mount PCB assembly. The primary design consideration is the power-down interface and the feedback network. Keep the power-down control signal electrically defined, place the feedback resistors close to the amplifier pins, and use short, low-inductance connections for high-speed output stages. Review the manufacturer application guidance before selecting resistor values or adding capacitive load to the output. This page combines verified manufacturer and distributor information with practical selection and design guidance.

見積もり お問い合わせ
THS3096D - Dual 160 MHz Current-Feedback Amplifier | Texas Instruments
THS3096D

THS3096D - Dual 160 MHz Current-Feedback Amplifier | Texas Instruments

Texas Instruments THS3096D is a dual, high-voltage, low-distortion current-feedback operational amplifier with power-down in a 14-pin SOIC package. The verified product data identifies it as a two-circuit current-feedback amplifier with a 160 MHz gain-bandwidth product, operating across a ±5 V to ±15 V supply range. Each amplifier includes a power-down control, allowing the device to enter a lower-power standby state when the output no longer needs to remain active. A current-feedback operational amplifier is a voltage-feedback amplifier subclass optimized for high-speed closed-loop gain stages. Unlike the dominant signal error of a conventional voltage-feedback amplifier, current-feedback amplifiers distribute distortion differently across frequency and gain. This makes them useful when a design must preserve low distortion while operating at high bandwidth, particularly with resistive feedback networks. The THS3096 family's main verified characteristics include dual-channel operation, 160 MHz bandwidth, a 14-SOIC package, and an extended operating-temperature range of -40°C to 85°C for the ordered THS3096D variant. The manufacturer identifies the devices as suitable for large linear output signals. The power-down feature adds an important system-level control: a system can reduce dissipation and disable the output path without removing the complete analog subsystem from the board. The THS3096D uses a current-feedback topology rather than the conventional voltage-feedback architecture used by many general-purpose op amps. Its two channels, wide supply range, and high operating bandwidth make it a candidate for analog signal-conditioning blocks that need substantial output swing and speed. Designers should still evaluate the exact gain, output-voltage, output-current, noise, and stability limits in the manufacturer datasheet before finalizing a circuit. Typical applications identified by Texas Instruments include power MOSFET and power-FET drivers, PIN-diode drivers, and VDSL line drivers. These applications benefit from the combination of wide supply capability, high speed, and low distortion. The dual-channel organization can also reduce board area when two related drive or signal-conditioning functions are required within the same system. The primary design consideration is that current-feedback amplifiers require appropriate feedback resistors and careful attention to board layout. Resistor values should follow the manufacturer's gain table rather than being copied directly from a voltage-feedback design. Ground, supply, and feedback paths should be short, and output-current demand must remain within the datasheet limits. This page consolidates verified manufacturer and distributor information, distinguishes documented characteristics from parameters requiring confirmation, and provides application, comparison, and design guidance beyond a basic distributor listing. Pricing reflects the available unit-price reference as of 2026-10-28, while unverified electrical details are explicitly marked for engineering review.

見積もり お問い合わせ
THS3112ID - Dual 110 MHz Current-Feedback Amplifier | Texas Instruments
THS3112ID

THS3112ID - Dual 110 MHz Current-Feedback Amplifier | Texas Instruments

Texas Instruments THS3112ID is a dual, low-noise, high-output-current current-feedback amplifier with a 110 MHz gain-bandwidth product, supplied in an 8-pin SOIC package. The device provides two amplifiers, 2.9 pA/√Hz noninverting current noise, 10.8 pA/√Hz inverting current noise, and the drive required by communication equipment, video-distribution circuits, motor drivers, and piezo drivers. A current-feedback amplifier is a voltage-feedback amplifier variant whose closed-loop bandwidth depends primarily on the feedback resistor rather than the closed-loop gain. This architecture is useful in high-speed signal paths because it can preserve bandwidth as gain increases, provided the feedback network, source impedance, and output loading are designed correctly. In the signal-chain hierarchy, the THS3112ID belongs to the operational-amplifier family, specifically high-speed current-feedback instrumentation amplifiers used for analog signal conditioning. The THS3112ID offers a 110 MHz gain-bandwidth product and low current noise, making it appropriate for wideband transimpedance, video, communications, and buffered-signal applications. Its current-feedback architecture supports high output drive, which is valuable when driving downstream analog stages, cable terminations, or capacitive loads. The dual configuration also allows two independent high-speed amplifier channels in one package, reducing board area in stereo, differential, or multi-channel signal-conditioning systems. In a transimpedance application, the inverting input serves as the summing node and a feedback resistor converts photocurrent or sensor current into voltage. The 10.8 pA/√Hz inverting current noise directly affects sensitivity in this topology. The 2.9 pA/√Hz noninverting current noise is especially relevant when the amplifier is configured with a non-inverting gain path. Capacitance at the summing node should be minimized because it interacts with the feedback network and can create peaking or instability. The device is commonly considered for communication equipment, video distribution, motor drivers, and piezo drivers. In video paths, the wide bandwidth allows larger closed-loop bandwidth than a conventional general-purpose amplifier. In motor and piezo systems, the high output-current capability can improve drive into reactive loads, although stability and safe operating limits must be checked for the actual load and output waveform. For PCB implementation, use a short feedback loop and place feedback resistors close to the inverting input. Keep the non-inverting input and ground-return paths compact to minimize parasitic capacitance and feedback from adjacent high-speed signals. Avoid capacitive loading directly at the output; use an isolation resistor when driving long cables or highly capacitive loads. This product page combines the manufacturer’s device information with package, lifecycle, and sourcing details, plus application guidance, design notes, and verified drop-in replacement analysis. Use the manufacturer datasheet pin-description table and ordering information as the authoritative references for final schematic, footprint, and qualification decisions.

見積もり お問い合わせ
THS3120ID - 475mA High-Output CFA | Texas Instruments
THS3120ID

THS3120ID - 475mA High-Output CFA | Texas Instruments

Texas Instruments THS3120ID is a single, low-noise, high-output-drive current-feedback operational amplifier rated for 475 mA output current, with a 130 MHz gain-bandwidth product and 1700 V/us slew rate. The device operates from +5 V to +15 V or -5 V to -15 V and is offered in an 8-pin SOIC package. A dedicated power-down function provides a controlled way to reduce power consumption when the amplifier is not required to operate. A current-feedback operational amplifier is a voltage-input, current-output amplifier topology that uses feedback to control gain. It belongs to the broader operational-amplifier and analog-signal-chain hierarchy. Unlike a conventional voltage-feedback amplifier, the THS3120ID transfers signal current through the feedback network, which supports high bandwidth, high slew rate, and strong drive capability in applications involving video, communications, instrumentation, and active filtering. The principal features of the THS3120ID are its 475 mA output-current capability, 130 MHz bandwidth, and 1700 V/us slew rate. Together, these characteristics allow the amplifier to generate large-amplitude, high-frequency signals while driving demanding loads. The low-noise architecture supports applications where amplifier noise would otherwise obscure weak signals. Power-down functionality helps reduce system power when the circuit is inactive, although its effect on overall energy use depends on the complete design. The current-feedback topology requires attention to feedback-resistor selection and compensation. Unlike a voltage-feedback amplifier, the THS3120ID generally does not provide a conventional gain-bandwidth product controlled by a single feedback resistor. Its gain, stability, and expected bandwidth depend on the feedback network and source impedance. Designers should use the manufacturer datasheet's recommended feedback values and evaluation methods when setting gain, particularly for large signals, low-frequency filtering, or capacitive-load drive. Typical applications include video-signal buffering, high-speed instrumentation, communications-interface amplification, active filters, and test-equipment output stages. The high output drive is useful when driving downstream stages through cables, terminations, transformers, or capacitive loads. The low-noise performance also makes the amplifier relevant to precision signal chains where preserving small-signal content is important. The 8-pin SOIC package supports conventional PCB assembly and thermal evaluation with conventional copper routing. A key design consideration is power-supply headroom. Because the output can reach 475 mA, both supply rails and the package must support the intended output amplitude and frequency. Output-voltage swing, output-current limit, supply voltage, and thermal dissipation should be checked together rather than independently. PCB layout should minimize feedback-loop area, keep the feedback network close to the amplifier, and provide adequate ground and supply return paths. This product data combines the manufacturer product information with practical guidance on current-feedback gain selection, feedback resistors, output drive, power-down control, and PCB implementation. It also identifies same-family alternatives and clearly separates electrically similar options from parts that require footprint, feature, or application verification before substitution.

見積もり お問い合わせ
THS3121ID - 475mA High-Output-Drive Current-Feedback Op Amp | Texas Instruments
THS3121ID

THS3121ID - 475mA High-Output-Drive Current-Feedback Op Amp | Texas Instruments

The Texas Instruments THS3121ID is a single low-noise, high-output-drive current-feedback operational amplifier with a 130 MHz unity-gain bandwidth, 1700 V/µs slew rate and 475 mA maximum output drive current, offered in an 8-pin SOIC (D) package. The same amplifier is also offered in an MSOP-8 PowerPAD (DGN) package for space-constrained layouts. A current-feedback amplifier (CFA) is a type of operational amplifier in which the inverting input node operates as a low-impedance summing junction and the feedback network sets the gain, rather than the gain being set by a differential input pair. This architecture allows closed-loop bandwidth to stay essentially flat as gain changes, which places the CFA in the broader hierarchy of voltage-feedback operational amplifiers -> analog signal-conditioning amplifiers -> integrated amplifier ICs. CFAs are the preferred building block for wideband, high-impedance-sensing and cable-driver stages where voltage-feedback op amps lose stability at low noise gains. Key features of the THS3121 include 130 MHz unity-gain bandwidth for low distortion at 10 MHz, a very high 1700 V/µs slew rate that produces large output voltage swings at high frequencies, and up to 475 mA of output current, allowing it to drive low-impedance loads, long cables, and capacitive loads without external buffers. The device is specified for wide supply operation of ±5 V to ±15 V, and the manufacturer describes it as a low-noise, high-output-drive amplifier intended for high-performance analog signal chains. Internally, the THS3121 uses a current-feedback core whose bandwidth is set by the external feedback resistor rather than by a fixed gain-setting network, so a single amplifier can serve gain stages from roughly 1 V/V to 20 V/V while keeping distortion low. Because the output stage can source and sink several hundred milliamps, the part maintains large-signal integrity into 50 ohm and 32 ohm loads, and its drive capability reduces the need for external output buffers in instrumentation chains. Typical applications include low-noise instrumentation preamplifiers, high-speed current-sense amplifiers, video and broadcast distribution buffers, ultrasonic and audio driver stages, laboratory test equipment, and general-purpose high-speed analog signal conditioning. The same footprint also serves any application needing accurate gain at 10 MHz with low harmonic distortion. When designing with the THS3121, choose the feedback resistor carefully because its value directly sets both bandwidth and gain in a current-feedback amplifier, and check that the load does not exceed the specified 475 mA output drive. Place the feedback resistor close to the inverting input pin to minimize parasitic capacitance that would otherwise reduce stability. This page consolidates manufacturer device data, drop-in replacement options in the same SOIC-8 footprint, and practical layout and stability guidance that are not collected together in the manufacturer datasheet.

見積もり お問い合わせ
THS3201D - 1.8 GHz Current-Feedback Amplifier | Texas Instruments
THS3201D

THS3201D - 1.8 GHz Current-Feedback Amplifier | Texas Instruments

The Texas Instruments THS3201D is a single current-feedback operational amplifier with a 1.8 GHz unity-gain bandwidth, a 10,500 V/µs slew rate, and an operating supply range of ±3.3 V to ±7.5 V. The device is packaged in an 8-pin SOIC for high-speed instrumentation, arbitrary waveform generation, and high-resolution or high-sample-rate analog-to-digital converter drive applications. A current-feedback amplifier is a voltage-input, current-output amplifier topology that commonly uses feedback resistors to establish gain. Unlike a conventional voltage-feedback amplifier, its closed-loop bandwidth can remain comparatively stable as feedback resistance changes, making the THS3201D suitable for demanding high-bandwidth signal chains. Within the broader semiconductor hierarchy, the THS3201D is an analog operational amplifier, then an amplifier IC, and finally a signal-chain IC. The principal performance features are its 1.8 GHz unity-gain bandwidth, 10,500 V/µs slew rate, and broad ±3.3 V to ±7.5 V supply range. These characteristics support fast edge generation and accurate amplification of high-frequency waveforms. The manufacturer datasheet also identifies low-distortion operation as a key benefit for arbitrary waveform drivers and high-resolution, high-sampling-rate ADC applications. The THS3201D combines wide supply flexibility with high-speed edge-rate capability. Its current-feedback architecture is particularly relevant when driving capacitive ADC inputs, where large input capacitance can otherwise reduce the effective bandwidth of a voltage-feedback amplifier. Designers must nevertheless evaluate gain-setting resistors, source and load impedances, PCB parasitics, and output-current requirements as a complete signal chain rather than relying only on headline bandwidth. Typical uses include arbitrary waveform generation, high-speed ADC input drivers, communications test equipment, and instrumentation requiring low distortion at high frequency. In these systems, the amplifier converts a source waveform into a sufficiently large, fast, and accurate signal to meet the driven device's input requirements. The SOIC-8 package also supports conventional surface-mount PCB assembly. The primary design consideration is gain configuration. A current-feedback amplifier generally uses separate input and feedback resistors, and their values influence bandwidth, noise, stability, and output drive. PCB layout should minimize trace capacitance and maintain short feedback paths. Decoupling capacitors should be positioned close to the supply pins, while output routing should avoid long traces or capacitive loads that could compromise stability. This product page combines the verified manufacturer specifications, distributor availability information, package details, pricing status, application guidance, and design considerations in one searchable reference. It also distinguishes confirmed device facts from parameters that require confirmation from the complete datasheet, avoiding unsupported assumptions about electrical characteristics that are not present in the supplied search record.

見積もり お問い合わせ
THS3202D - 2GHz Dual Current-Feedback Amplifier | Texas Instruments
THS3202D

THS3202D - 2GHz Dual Current-Feedback Amplifier | Texas Instruments

The Texas Instruments THS3202D is a dual current-feedback amplifier with 2 GHz unity-gain bandwidth, a 9000 V/us slew rate, and dual amplifiers in an 8-SOIC package. Designed with BiCOM-II technology, it targets high-frequency, low-distortion signal paths and supports supply rails from ±3.3 V to ±7.5 V. A current-feedback amplifier is a voltage-feedback amplifier subclass that uses an inverting input as the principal high-frequency feedback node. Unlike a conventional voltage-feedback amplifier, its bandwidth and phase behavior are less dependent on closed-loop gain. The THS3202D uses this architecture for high-speed amplification where large signals, high slew rate, and low distortion are more important than the familiar gain-bandwidth relationship of voltage-feedback devices. The verified manufacturer information identifies a 2 GHz unity-gain bandwidth and a 9000 V/us high slew rate. These headline specifications make the device suitable for video and test-and-measurement signal chains, active filtering, communications equipment, and other applications that drive distortion-sensitive loads at high frequency. The dual configuration allows two amplifier channels to share one package while preserving consistent high-speed performance. BiCOM-II is the process technology named by Texas Instruments for the THS3202 family. The family is designed for low distortion at high frequencies, with the manufacturer explicitly positioning it for loads sensitive to distortion. Its current-feedback topology makes gain-setting resistors and feedback-branch layout especially important; resistor values, parasitic capacitance, and trace geometry must be controlled to preserve intended bandwidth and stability. The THS3202 is offered by Texas Instruments in SOIC-8, MSOP-8, and MSOP-8 with PowerPAD packages according to the verified product-page snippet. The THS3202D ordering suffix denotes the SOIC-8 configuration in the supplied distributor result. Typical signal-chain uses include video amplification, communications interfaces, instrumentation, active filters, and high-speed buffers, subject to the device's complete datasheet limits and external-component recommendations. For implementation, begin with the manufacturer datasheet's recommended feedback and gain-setting networks rather than treating the 2 GHz bandwidth as an unconditional operating frequency. Keep the feedback loop compact, use low-inductance routing, provide adequate bypassing, and verify stability and distortion with the intended load and signal amplitude. The distinction between voltage bandwidth, closed-loop gain, slew rate, and output loading is essential when comparing this part with other high-speed amplifiers. This page consolidates the verified manufacturer identity, package information, headline performance, pricing availability, and engineering guidance for the THS3202D. It is intended to help engineers identify whether this dual current-feedback amplifier matches a high-speed signal-chain requirement before requesting a quote or reviewing the full manufacturer documentation.

見積もり お問い合わせ
THS4001CD - 270MHz High-Speed Voltage-Feedback Amplifier | TI
THS4001CD

THS4001CD - 270MHz High-Speed Voltage-Feedback Amplifier | TI

The Texas Instruments THS4001CD is a single-circuit, voltage-feedback operational amplifier designed for high-speed video and signal-conditioning systems. Its headline specifications are 270 MHz gain-bandwidth product, greater than 400 V/µs slew rate, and less than 30 ns settling time. The device is packaged in an 8-pin SOIC (D) package. A voltage-feedback operational amplifier is a high-gain amplifier that uses voltage feedback to control its closed-loop response. This architecture belongs to the operational-amplifier family, within analog signal-chain ICs and the broader semiconductor category. Voltage-feedback amplifiers are especially useful for wideband signal amplification because they can provide high bandwidth and fast slew performance without relying on the slower settling behavior commonly associated with current-feedback implementations. The THS4001 combines several performance characteristics intended for demanding analog systems. Its 270 MHz gain-bandwidth product supports operation at high closed-loop signal frequencies, while its slew rate above 400 V/µs allows large output-voltage transitions to occur rapidly. According to the Texas Instruments THS4001 data sheet, settling time is below 30 ns for the stated test condition. The device also provides output-drive capability of 100 mA and low video distortion, including 0.15° differential phase and 0.1% differential-gain bandwidth of 60 MHz. The THS4001 operates across dual supply voltages from ±15 V down to ±2.5 V. Its voltage-feedback configuration supports conventional resistor-based gain networks and stable operation as a high-speed closed-loop amplifier. The manufacturer positions the device for wide-range video applications, where broad bandwidth, rapid slew rate, and low differential gain and phase errors are important for preserving signal fidelity. Typical uses include video routing, video buffering, waveform conditioning, high-speed instrumentation, and test-equipment signal chains. It can also be used where a low-voltage, high-speed feedback amplifier is needed around sensors, converters, or communications interfaces. The 100 mA output-drive capability makes it relevant to stages that must drive downstream circuitry while preserving large-amplitude signal transitions. Circuit implementation requires careful attention to feedback-loop stability, parasitic capacitance, grounding, and trace impedance. Short, direct feedback paths and symmetrical routing help preserve the intended 270 MHz bandwidth. Decoupling capacitors should be placed close to the supply pins, while controlled impedance and adequate ground-plane continuity are important in designs operating at high signal rates. This product page consolidates the manufacturer specifications, package information, drop-in family alternatives, comparison data, and application guidance needed to evaluate the THS4001CD before PCB implementation. Use the Texas Instruments data sheet as the controlling reference for pin assignments, electrical limits, test conditions, and recommended operating procedures.

見積もり お問い合わせ
THS4001ID - 270MHz High-Speed Voltage-Feedback Op Amp
THS4001ID

THS4001ID - 270MHz High-Speed Voltage-Feedback Op Amp

Texas Instruments THS4001ID is a single-channel, high-speed voltage-feedback operational amplifier with 270 MHz bandwidth, slew rate above 400 V/μs, and settling time below 30 ns, housed in an 8-pin SOIC package. It is designed for high-speed video and instrumentation circuits requiring wide bandwidth, fast transient response, and strong output-drive capability. A voltage-feedback operational amplifier is an amplifier category in which the inverting input provides the feedback path. This architecture supports closed-loop gain control while maintaining high bandwidth and slew rate. Within the integrated-circuit hierarchy, the THS4001ID belongs to the amplifier IC, operational amplifier, and high-speed analog signal-chain categories. The principal performance characteristics are 270 MHz small-signal bandwidth, greater than 400 V/μs slew rate, less than 30 ns settling time, and 100 mA output drive. Video performance includes 60 MHz bandwidth with 0.1 dB differential gain variation, 0.15° differential phase, and very low distortion. These figures make the amplifier appropriate for video routing, active filtering, pulse shaping, and test-equipment input stages. The THS4001 operates from dual supplies ranging from ±2.5 V to ±15 V. Its voltage-feedback configuration permits gain to be established with external resistors while retaining high-speed performance. The combination of wide bandwidth and slew rate reduces distortion for large or rapidly changing signals, while the settling-time specification is particularly useful when accurate waveform recovery is required after a transition. Typical uses include professional video distribution, broadcast and monitoring equipment, high-resolution imaging interfaces, active filters, laboratory instrumentation, and general-purpose high-speed signal conditioning. Its 8-pin SOIC package supports conventional surface-mount assembly, although careful component placement and short feedback paths are important at these operating frequencies. For high-speed layouts, minimize trace lengths around the input and feedback pins, use a low-inductance ground reference, and place input and feedback components close to the amplifier. Avoid long PCB routes and excessive capacitance on sensitive input nodes, because parasitic reactance can reduce bandwidth and increase ringing. This product page combines the manufacturer specifications with application guidance, pin-layout requirements, comparison information, and practical design considerations. It is intended to help engineers determine whether the THS4001ID provides the required bandwidth, slew rate, voltage range, package, and drive capability without overlooking layout-related performance losses.

見積もり お問い合わせ
THS4011ID - 290MHz High-Speed Amplifier | Texas Instruments
THS4011ID

THS4011ID - 290MHz High-Speed Amplifier | Texas Instruments

The Texas Instruments THS4011ID is a single-circuit, low-distortion voltage-feedback operational amplifier with 290 MHz bandwidth, a 310 V/µs slew rate, and a 37 ns 0.1% settling time. Designed for low-voltage operation, the device uses a ±5 V supply architecture and is packaged in an 8-pin SOIC. According to the manufacturer datasheet, the THS4011 also provides 110 mA output-current drive capability and consumes 7.8 mA per channel. A high-speed voltage-feedback amplifier is a wide-bandwidth operational amplifier that uses negative feedback to control gain, bandwidth, and output impedance. Within the broader semiconductor hierarchy, this amplifier belongs to the operational-amplifier family, then to linear and signal-conditioning ICs. Its combination of large bandwidth, high slew rate, and low distortion makes it appropriate for systems that process fast analog waveforms while requiring predictable signal amplitude and timing. The headline performance of the THS4011 includes 290 MHz bandwidth, 310 V/µs slew rate, 37 ns settling time to 0.1%, and 110 mA typical output-current drive. The manufacturer datasheet also specifies low-distortion performance of -80 dBc at 1 MHz and input-voltage noise density of 7.5 nV/√Hz. These characteristics are particularly valuable in video, communications, test-and-measurement, and high-speed feedback networks where bandwidth alone does not fully describe usable amplifier performance. The amplifier uses a voltage-feedback architecture optimized for high-speed closed-loop operation. Its 310 V/µs slew rate allows the output to follow rapidly changing input signals, while the 37 ns settling specification provides a useful basis for timing design. The 110 mA output-drive capability supports wider bandwidth into heavier loads than a small-signal amplifier with limited drive current, although load stability and parasitic capacitance still require careful evaluation. Typical applications include analog video amplification, communications infrastructure, high-speed instrumentation, active filters, and low-distortion signal-conditioning stages. In each case, the amplifier can be used with external feedback components to establish the required closed-loop gain. The device is also suitable for test equipment requiring rapid transient response, provided the PCB layout controls parasitic capacitance and the selected gain remains stable at the required frequency. A key design consideration is that high bandwidth and slew rate do not eliminate the need for careful analog layout. Keep feedback-loop components close to the amplifier, use short and symmetric signal paths, and provide local supply bypassing. Designers should also check output swing, input common-mode range, load current, and stability for each operating point rather than relying only on the 290 MHz small-signal bandwidth figure. This product page combines the THS4011ID electrical characteristics, application guidance, pin-package information, and a parameter-by-parameter comparison with available alternatives. It also emphasizes practical PCB, output-drive, feedback, and signal-integrity considerations that help engineers evaluate the device beyond a basic distributor specification summary.

見積もり お問い合わせ
THS4012CD - 290MHz Dual High-Speed Amplifier | Texas Instruments
THS4012CD

THS4012CD - 290MHz Dual High-Speed Amplifier | Texas Instruments

Texas Instruments THS4012CD is a dual low-distortion voltage-feedback amplifier with 290 MHz bandwidth, a 310 V/µs slew rate, and a 37 ns settling time to 0.1%. Each channel operates from ±4.5 V to ±16 V and is housed in an 8-pin SOIC package. The device is designed for wideband signal chains that require high speed, low distortion, strong output drive, and accurate waveform reproduction. A high-speed voltage-feedback amplifier is a voltage-input amplifier that uses negative feedback to control gain and bandwidth. The THS4012 belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. Its voltage-feedback architecture supports signal conditioning, active filtering, video processing, communications, instrumentation, and test-equipment applications where conventional general-purpose amplifiers cannot provide sufficient bandwidth or slew rate. Key performance characteristics include 290 MHz small-signal bandwidth, 310 V/µs slew rate, and 37 ns settling time to 0.1%. The dual amplifier also provides 110 mA typical output-current drive, 7.8 mA supply current per channel, 7.5 nV/√Hz voltage-noise density, and low distortion characterized by THD of −80 dBc at 1 MHz. These specifications make the THS4012CD suitable for preserving high-amplitude, high-frequency waveforms without excessive slew distortion. The THS4012 family is specifically positioned for low-distortion and high-speed applications. Its 290 MHz bandwidth supports wideband video and communications paths, while the 310 V/µs slew rate permits rapid transitions through large voltage swings. The 37 ns settling time is useful in pulse, waveform-generation, and feedback-control systems that need signals to stabilize rapidly after a transition. Dual-channel operation also reduces the number of amplifiers required when two independent channels are needed. Typical applications include professional video equipment, communications receivers, high-speed instrumentation, active filters, signal conditioners, pulse-processing circuits, and wideband test systems. Two amplifiers can be configured independently for dual-channel processing or together for differential and other multichannel signal-chain functions. The 8-pin SOIC package supports conventional surface-mount assembly while keeping the implementation compact. Designers should preserve the feedback network and input/output impedance assumptions associated with the manufacturer’s recommended high-speed layout. Short feedback paths, careful grounding, controlled supply bypassing, and separation of sensitive inputs from output and supply traces help maintain stability and low distortion. Differential impedance and termination values should be calculated from the actual line standard rather than inferred solely from the 290 MHz bandwidth. This product page combines the manufacturer’s device characteristics with practical application guidance, package information, and verified drop-in alternatives. It is intended to help engineers evaluate the THS4012CD for bandwidth, distortion, output-drive, supply, layout, and replacement requirements before committing to an 8-pin SOIC design.

見積もり お問い合わせ
THS4012ID - 290 MHz Dual High-Speed Amplifier | Texas Instruments
THS4012ID

THS4012ID - 290 MHz Dual High-Speed Amplifier | Texas Instruments

The Texas Instruments THS4012ID is a dual, low-distortion voltage-feedback amplifier with 290 MHz gain-bandwidth product, 310 V/us slew rate, and 37 ns 0.1% settling time, housed in an 8-pin SOIC package. The device provides two amplifiers per package, 110 mA output-current drive capability, and 7.8 mA supply current per channel, making it suitable for high-speed signal-conditioning systems requiring fast response and low distortion. A voltage-feedback operational amplifier is an amplifier that uses feedback around a high-gain differential input stage to control closed-loop gain and bandwidth. Within the signal-chain hierarchy, the THS4012ID belongs to the operational-amplifier family, which supports analog signal conditioning, current-to-voltage conversion, buffering, gain adjustment, and active filtering. Its high closed-loop bandwidth makes it particularly useful when signals must be amplified or routed without substantial attenuation at high frequencies. Principal performance features include 290 MHz bandwidth, 310 V/us slew rate, and 37 ns settling to 0.1%. The low-distortion architecture is specified for low total harmonic distortion, while the 7.5 nV/sqrt(Hz) input-voltage-noise figure supports sensitive high-speed signal paths. Each channel can source or sink up to 110 mA, providing useful drive capability for downstream stages, termination networks, and active filter elements. The THS4012 uses a voltage-feedback topology intended for closed-loop operation with resistive feedback components. Its 290 MHz bandwidth and 310 V/us slew rate support video, communications, test-and-measurement, and instrumentation applications. The dual configuration saves board area when two amplified channels are required, while the 7.8 mA-per-channel supply current keeps power demand manageable compared with many high-speed amplifiers. Typical uses include high-speed video amplification, analog signal conditioning, active filtering, pulse shaping, communications interfaces, and precision test equipment. The reported 70 MHz video bandwidth makes the device relevant to video-processing chains, while its fast settling behavior is useful when waveforms must stabilize rapidly after a transition. PCB implementation should minimize feedback-loop length, preserve symmetric routing around the amplifier, and provide local supply bypassing. Short ground returns and careful control of parasitic capacitance are particularly important at 290 MHz. Component tolerances, board leakage, and probe or fixture loading should also be checked against the required closed-loop gain and bandwidth. This product page combines manufacturer specifications, package details, application guidance, and drop-in replacement analysis with practical PCB and signal-integrity considerations. It is intended to help engineers select the THS4012ID, evaluate equivalent amplifiers, and plan a high-speed amplifier layout without relying on a single raw specification list.

見積もり お問い合わせ
THS4021ID - 290 MHz Low-Noise Op Amp | Texas Instruments
THS4021ID

THS4021ID - 290 MHz Low-Noise Op Amp | Texas Instruments

Texas Instruments THS4021ID is a single-channel, ultra-low-noise voltage-feedback amplifier featuring 2 GHz gain-bandwidth performance, 290 MHz closed-loop bandwidth, 470 V/µs slew rate, and 30 ns settling time to 0.1%, all in an 8-pin SOIC package. It is designed for high-speed signal chains requiring low voltage noise. A voltage-feedback amplifier is an active analog signal-conditioning device that uses negative feedback to control gain and bandwidth. The THS4021 belongs to the operational-amplifier hierarchy, combining low input-referred voltage noise with high-speed closed-loop operation. This combination makes it suitable for communications receivers, imaging systems, instrumentation, test equipment, and other circuits that must preserve small signals at high frequencies. According to the Texas Instruments THS4021 product page and manufacturer datasheet, principal features include 2 GHz gain-bandwidth product, 290 MHz closed-loop bandwidth, 470 V/µs slew rate, and 30 ns settling time to 0.1%. The device is a single amplifier rather than a dual amplifier, reducing channel count where only one high-speed signal path is required. Its low voltage noise is particularly important when amplification occurs before a downstream converter or measurement stage. The amplifier uses a voltage-feedback architecture, which provides direct control of gain through external feedback components when configured for inverting, non-inverting, and summing operation. The high gain-bandwidth product supports operation over a broad frequency range, while the 290 MHz closed-loop bandwidth defines its practical response in the gain configuration used by the design. The 470 V/µs slew rate helps preserve large-amplitude, high-frequency waveforms without excessive distortion. Typical uses include low-noise communications front ends, imaging and photodetector signal paths, high-speed instrumentation, analog test equipment, and clock or data conversion interfaces. The device can also serve in broadband transimpedance and active-filter stages where low noise and rapid settling are both valuable. Actual signal bandwidth depends on gain, feedback impedance, output loading, trace impedance, and the bandwidth of surrounding components. PCB implementation should use short, controlled-impedance connections and minimize parasitic capacitance at the high-impedance input node. Place feedback components close to the amplifier, provide a stable low-impedance supply reference, and follow the manufacturer pinout and layout guidance. Termination, decoupling, and probe measurements must be treated as part of the complete high-frequency circuit rather than as isolated component choices. This product page combines the manufacturer specifications, package details, verified source links, application guidance, and a conservative drop-in cross-reference assessment. It also distinguishes a confirmed same-package option from alternatives that lack sufficient evidence for PCB-level substitution, helping designers compare options without treating electrically similar amplifiers as guaranteed pin-to-pin replacements.

見積もり お問い合わせ
THS4031 - 100MHz 1.6nV Low-Noise Op Amp | Texas Instruments
THS4031

THS4031 - 100MHz 1.6nV Low-Noise Op Amp | Texas Instruments

The Texas Instruments THS4031 is a single-channel, ultra-low voltage noise, high-speed voltage feedback amplifier delivering a 100-MHz bandwidth at gain of 2, a 100-V/us slew rate, and a 60-ns settling time (0.1%). It operates from a supply range of +/-5V to +/-15V, provides 90 mA output drive, and draws only 8.5-mA supply current per channel, in an 8-pin HVSSOP (DGK) package with power pad. A voltage feedback amplifier is a type of operational amplifier that uses voltage feedback to set closed-loop gain, offering high bandwidth and low distortion. It is a fundamental analog signal-chain building block used in buffer, filter, and gain stages. The THS4031 belongs to the high-speed amplifier family, a subset of operational amplifiers designed for fast, low-noise signal conditioning. Key features include ultra-low 1.6 nV/Hz voltage noise, very low distortion (THD = -72 dBc at 1 MHz with RL = 100 ohm, -90 dBc at 1 MHz with RL = 1k ohm), and a low 0.5-mV typical input offset voltage. The amplifier is stable in gains of -1 or greater with a 275-MHz unity-gain bandwidth, ensuring stable operation in high-frequency signal paths. The THS4031 uses a complementary bipolar process that achieves low noise and high speed simultaneously, providing excellent AC performance while maintaining low DC errors. The HVSSOP (DGK) package is compact and thermally efficient when its power pad is soldered to a copper plane. Typical applications include communication systems, imaging systems, active filters, and ADC drivers. In communication receivers, the 1.6 nV/Hz noise floor preserves signal integrity; in imaging systems, the 60-ns settling time enables accurate pixel processing; the 90-mA output drives heavy loads directly. Design tip: decouple supplies with 0.1-uF ceramic capacitors close to the supply pins, and solder the thermal pad to a ground plane for adequate heat dissipation. The device is RoHS compliant and operates over the -40C to +85C industrial temperature range.

見積もり お問い合わせ
THS4031CD - 100MHz Low-Noise Voltage Feedback Op Amp | TI (Tape & Reel)
THS4031CD

THS4031CD - 100MHz Low-Noise Voltage Feedback Op Amp | TI (Tape & Reel)

The Texas Instruments THS4031CD is a 100 MHz single-channel low-noise voltage-feedback operational amplifier delivering a 100 V/us slew rate and 60 ns settling time to 0.1%, supplied in an 8-pin SOIC (D) package on tape and reel. A voltage-feedback operational amplifier is a high-gain differential amplifier whose closed-loop bandwidth is set by the feedback network and the amplifier's gain-bandwidth product. Within the signal-chain hierarchy, it sits in the amplifier IC category alongside current-feedback and fully differential amplifiers, serving as a building block for filters, gain stages, buffers, and driver circuits in analog front ends. Key features of the THS4031 include a 100 MHz bandwidth at a gain of 2, unity-gain stability with a 275 MHz open-loop bandwidth, an ultra-low input voltage noise of [DATA_NEEDED: input voltage noise], and high DC precision with 90 dB CMRR. The device operates from supplies up to +/-16 V (32 V total), giving wide signal-swing headroom uncommon in lower-voltage high-speed amplifiers. The bipolar input architecture of the THS403x family combines very low voltage noise with high-speed settling, making it well suited for driving ADC inputs and video-type loads. According to the TI datasheet, the amplifier achieves 60 ns settling to 0.1% for a 2 V step, which supports high-throughput data-acquisition systems requiring fast, accurate settling between channel switches. Typical applications include ADC input drive in instrumentation, active filter stages in test and measurement equipment, video and high-speed signal conditioning, and IF-stage gain blocks in communications receivers where low noise and 100 MHz bandwidth are required. Design-wise, the THS4031 is unity-gain stable, but layout discipline matters at these speeds: minimize feedback-loop area, keep the gain resistor values low, and decouple supply pins with 0.1 uF ceramics placed close to pins 7 and 3 to preserve bandwidth and stability. This page adds value beyond the TI datasheet by synthesizing distributor availability, drop-in same-brand alternatives (THS4031IDR/THS4031ID), and practical high-speed layout guidance in one citable reference.

見積もり お問い合わせ
THS4031CDGNR - 100MHz Low-Noise Op Amp | Texas Instruments
THS4031CDGNR

THS4031CDGNR - 100MHz Low-Noise Op Amp | Texas Instruments

The Texas Instruments THS4031CDGNR is a single-channel, 100 MHz low-noise high-speed voltage-feedback amplifier delivering 1.6 nV/Hz input voltage noise, 100 V/us slew rate, and 90 mA output current in an 8-pin MSOP (DGN, PowerPAD HVSSOP) package. A voltage-feedback operational amplifier is a differential-input, high-gain amplifier whose closed-loop bandwidth is set by an external feedback network, making it the workhorse of the analog signal chain within the broader amplifier family: op amp -> linear amplifier -> signal conditioning IC. Unlike current-feedback topologies, voltage-feedback parts allow symmetric impedances and conventional filter topologies, which is why they dominate precision and low-noise designs. Key features of the THS4031CDGNR include ultra-low 1.6 nV/Hz voltage noise for high dynamic range, 100 MHz bandwidth at a gain of 2, and very low distortion of -72 dBc THD at 1 MHz. The 60 ns settling time to 0.1% supports fast data-acquisition loops, and the PowerPAD MSOP-8 package provides a low thermal-resistance path for reliable high-output-current operation. Architecturally, the THS403x family uses a bipolar high-speed complementary process that trades moderate quiescent power for exceptionally low input voltage noise, which dominates total noise in low-impedance sources. The 0.5 mV typical input offset voltage keeps DC accuracy adequate for AC-coupled and gain-trimmed designs. Typical applications include communications receiver front ends, imaging signal chains, ADC and DAC buffer stages, IF amplifiers, and test-and-measurement instrumentation where noise floor directly limits resolution. Design consideration: keep feedback resistors low (hundreds of ohms) so resistor noise does not swamp the 1.6 nV/Hz amplifier noise, and use the PowerPAD soldered to a copper pour for thermal dissipation. This page adds value beyond the datasheet by synthesizing distributor stock links, drop-in alternative analysis, and practical design notes in one place.

見積もり お問い合わせ
THS4031CDR - 100MHz Low-Noise Voltage Feedback Op Amp | TI
THS4031CDR

THS4031CDR - 100MHz Low-Noise Voltage Feedback Op Amp | TI

The Texas Instruments THS4031CDR is a 100 MHz single-channel low-noise voltage-feedback operational amplifier delivering a 100 V/us slew rate and 60 ns settling time to 0.1%, supplied in an 8-pin SOIC (D) package on tape and reel. A voltage-feedback operational amplifier is a high-gain differential amplifier whose closed-loop bandwidth is set by the feedback network and the amplifier's gain-bandwidth product. Within the signal-chain hierarchy, it sits in the amplifier IC category alongside current-feedback and fully differential amplifiers, serving as a building block for filters, gain stages, buffers, and driver circuits in analog front ends. Key features of the THS4031 include a 100 MHz bandwidth at a gain of 2, unity-gain stability with a 275 MHz open-loop bandwidth, an ultra-low input voltage noise of [DATA_NEEDED: input voltage noise], and high DC precision with 90 dB CMRR. The device operates from supplies up to +/-16 V (32 V total), giving wide signal-swing headroom uncommon in lower-voltage high-speed amplifiers. The bipolar input architecture of the THS403x family combines very low voltage noise with high-speed settling, making it well suited for driving ADC inputs and video-type loads. According to the TI datasheet, the amplifier achieves 60 ns settling to 0.1% for a 2 V step, which supports high-throughput data-acquisition systems requiring fast, accurate settling between channel switches. Typical applications include ADC input drive in instrumentation, active filter stages in test and measurement equipment, video and high-speed signal conditioning, and IF-stage gain blocks in communications receivers where low noise and 100 MHz bandwidth are required. Design-wise, the THS4031 is unity-gain stable, but layout discipline matters at these speeds: minimize feedback-loop area, keep the gain resistor values low, and decouple supply pins with 0.1 uF ceramics placed close to pins 7 and 3 to preserve bandwidth and stability. This page adds value beyond the TI datasheet by synthesizing distributor availability, drop-in same-brand alternatives (THS4031IDR/THS4031ID), and practical high-speed layout guidance in one citable reference.

見積もり お問い合わせ
THS4031IDGNR - 100MHz Low-Noise VFB Amplifier | Texas Instruments
THS4031IDGNR

THS4031IDGNR - 100MHz Low-Noise VFB Amplifier | Texas Instruments

The Texas Instruments THS4031IDGNR is a single-channel, 100-MHz low-noise voltage-feedback amplifier delivering 100 V/us slew rate and an ultra-low 1.6 nV/√Hz input voltage noise, housed in an 8-pin HVSSOP (DGN) PowerPAD package rated from -40C to +85C. A voltage-feedback amplifier (VFA) is an operational amplifier in which the feedback network controls the differential input voltage, giving it a constant gain-bandwidth product. Within the signal-chain hierarchy, the VFA sits in the amplifier family (op amp -> amplifier -> analog signal conditioning IC) and is the classical choice where the designer wants the gain-bandwidth trade-off of a conventional feedback topology rather than the fixed-gain behavior of a current-feedback amplifier (CFA). The defining feature of the THS4031 is its 1.6 nV/√Hz voltage noise, among the lowest available in its class, which directly improves SNR in wideband analog front ends. It is stable in noise gains of 1 V/V or greater, delivers 100 V/us slew rate, and exhibits low distortion with THD of -72 dBc at 1 MHz into low-impedance loads and -90 dBc at 1 MHz into 1 kΩ. The typical input offset voltage is only 0.5 mV, and the output drives approximately 90 mA, enough for back-terminated 50-ohm and 75-ohm video/RF lines. Architecturally, the THS4031 pairs a low-noise bipolar input stage with a high-bandwidth voltage-feedback core, and the DGN PowerPAD package provides a low thermal-resistance path to the PCB so the die stays cool at high supply voltages of up to ±16 V. This combination of noise, bandwidth, and drive makes it suitable for communications receivers, imaging signal chains, ADC input drivers, and IF/RF gain blocks. Typical applications include low-noise gain stages ahead of high-speed ADCs, ultrasound and CCD imaging front ends, and broadband test-and-measurement amplification. The supply range of ±4.5 V to ±16 V supports both ±5 V and ±15 V analog rails. Design consideration: at high closed-loop gains the 100 MHz bandwidth scales down by the gain-bandwidth product, so budget bandwidth at your actual noise gain and use the PowerPAD soldered to a solid ground plane. This page adds distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
THS4031IDR - 100MHz Low-Noise Voltage Feedback Op-Amp | TI
THS4031IDR

THS4031IDR - 100MHz Low-Noise Voltage Feedback Op-Amp | TI

The Texas Instruments THS4031IDR is a single-channel, ultra-low-noise, high-speed voltage-feedback operational amplifier delivering a 100 MHz bandwidth at a gain of 2 (275 MHz unity-gain stable bandwidth), a 100 V/µs slew rate, and 90 dB CMRR, housed in an 8-pin SOIC (D) package rated for -40C to +85C operation. A voltage-feedback amplifier (VFA) is a type of operational amplifier in which the feedback network senses voltage at the input pins, as opposed to a current-feedback amplifier (CFA) which senses current. Within the signal-chain hierarchy, the op-amp belongs to the amplifier IC family, which sits under linear ICs and ultimately analog semiconductors. Voltage-feedback topologies are preferred where symmetric input impedance, precision DC accuracy, and conventional feedback network design techniques are required. Key differentiating features of the THS4031 include its ultra-low input voltage noise, high 100 MHz bandwidth at G=2, 60 ns settling time to 0.1%, and high output drive capability. The 90 dB CMRR and low voltage noise make it particularly effective in the first stages of low-level signal chains, where noise floor directly limits dynamic range and resolution. Architecturally, the THS4031 uses a voltage-feedback input stage optimized for low noise rather than lowest power, trading quiescent current for wideband, low-noise performance. The output stage is designed with high drive capability to support communications and imaging loads, maintaining AC performance into practical capacitive and resistive loads encountered in real signal chains. Typical applications include communications receivers and transmitters, imaging systems, high-speed data acquisition front ends, IF and RF gain blocks, and low-noise buffer stages for ADC drivers, where the combination of 100 MHz bandwidth and ultra-low voltage noise directly improves system SNR. A key design consideration is power-supply decoupling: at 100 MHz bandwidth, place low-inductance 0.1 µF ceramic capacitors directly at the supply pins and use a solid ground plane to prevent instability. Also verify gain-bandwidth margin, as the 100 MHz bandwidth is specified at a gain of 2. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in a single manufacturer datasheet, providing unique cross-reference value for engineers and buyers.

見積もり お問い合わせ
THS4031Q-Q1 - 100MHz 1.6nV Low-Noise Op Amp AEC-Q100 | TI
THS4031Q-Q1

THS4031Q-Q1 - 100MHz 1.6nV Low-Noise Op Amp AEC-Q100 | TI

The Texas Instruments THS4031Q-Q1 is an automotive-qualified (AEC-Q100) version of the THS4031, an ultra-low voltage noise, high-speed voltage feedback operational amplifier delivering 100 MHz bandwidth at a gain of 2, 100 V/us slew rate, and just 1.6 nV/rtHz input voltage noise. It comes in an HTSSOP-8 PowerPAD (DDA) package for enhanced thermal dissipation. A high-speed operational amplifier is a voltage feedback amplifier optimized for wide bandwidth and fast settling, sitting within the amplifier IC hierarchy of linear signal chain components. The THS4031 family (single THS4031, dual THS4032) is engineered specifically for applications where low voltage noise dominates system SNR, such as communications receivers and imaging front ends. Key features include ultra-low 1.6 nV/rtHz voltage noise, 100 MHz bandwidth (G = 2), 100 V/us slew rate, and 70 ns settling time to 0.1%. Distortion is very low: THD = -72 dBc at 1 MHz into 100 ohms and -90 dBc at 1 MHz into 1 kohm. Input offset voltage is a low 0.5 mV (typ) with 90 mA output current drive capability, allowing the amplifier to directly drive low-impedance loads and ADC inputs. The voltage feedback architecture remains stable in gains of -1 V/V or greater, and the PowerPAD package provides a low thermal resistance path that keeps junction temperatures safe during high-output-current operation. The Q-Q1 suffix denotes AEC-Q100 qualification and PPAP support for automotive design flows. Typical applications include automotive communications and imaging systems, wideband transimpedance and RF/IF gain stages, active filters, and ADC buffer drivers where 1.6 nV/rtHz noise preserves dynamic range. Design consideration: use a low-impedance feedback network (typically below 1 kohm) because resistor thermal noise can easily exceed the amplifier's intrinsic 1.6 nV/rtHz; also solder the PowerPAD to a copper pour for rated thermal performance.

見積もり お問い合わせ
THS4032CD - 100MHz Dual Low-Noise Amplifier | Texas Instruments
THS4032CD

THS4032CD - 100MHz Dual Low-Noise Amplifier | Texas Instruments

Texas Instruments THS4032CD is a dual-channel, low-noise, high-speed voltage-feedback amplifier with 100 MHz bandwidth, 100 V/us slew rate, and a low-noise density of 1.6 nV/sqrt(Hz). It is packaged in an 8-pin SOIC for instrumentation, communications, imaging, and high-speed analog signal-chain applications. The device is designed to combine wideband frequency response with low input-voltage noise and low distortion. A voltage-feedback amplifier is a general-purpose analog building block that uses negative feedback to control gain and bandwidth. Within the broader operational-amplifier hierarchy, the THS4032 belongs to the low-noise, high-speed precision-amplifier class. Its dual configuration provides two amplifiers in one package, allowing designers to implement matching gain stages, differential circuits, filters, line drivers, or two independent channels while reducing board area. The manufacturer datasheet identifies several performance characteristics suited to demanding analog front ends. The THS403x family offers 100 MHz bandwidth at a gain of 2, 100 V/us slew rate, and approximately 70 ns settling time. Input-voltage noise is 1.6 nV/sqrt(Hz), while typical input offset voltage is 0.5 mV. Distortion values cited in the family documentation include -72 dBc and -90 dBc under specified 1 MHz test conditions. The amplifier is stable in gains of -1 or greater. The THS4032 is particularly useful for buffering analog-to-digital converters, processing communications signals, and amplifying low-level imaging waveforms. Its combination of bandwidth and low noise is valuable when a signal must retain both temporal fidelity and amplitude accuracy. The 8-pin SOIC package also supports conventional surface-mount assembly and prototyping workflows. Designers should use the manufacturer datasheet for the exact input and output swing limits, supply-current behavior, electrical characteristics over temperature, pin assignments, and recommended operating conditions. Feedback-network values, source and load impedances, and PCB trace geometry can materially affect high-speed stability and distortion. Input and output paths should therefore be short, and sensitive inputs should be isolated from return currents and switching-node energy. This product page consolidates manufacturer specifications, sourcing guidance, verified replacement candidates, and practical high-speed layout considerations into an engineering-focused reference for evaluating the THS4032CD in precision analog systems.

見積もり お問い合わせ
THS4041CD - 165MHz High-Speed Amplifier | Texas Instruments
THS4041CD

THS4041CD - 165MHz High-Speed Amplifier | Texas Instruments

The Texas Instruments THS4041CD is a single, C-stable, high-speed voltage-feedback amplifier with 165 MHz bandwidth, 400 V/µs slew rate, and unity-gain stability in an 8-pin SOIC package. The device operates from ±5 V to ±16 V, equivalent to a 10 V to 32 V total supply range. It is designed to drive capacitive loads and provides low distortion, including typical THD of -75 dBc at 1 MHz. A high-speed operational amplifier is a voltage-feedback amplifier optimized for wide bandwidth, rapid output transitions, and low distortion. Its hierarchy is operational amplifier, voltage-feedback amplifier, analog signal-conditioning IC, and semiconductor. The THS4041 occupies the high-speed end of that hierarchy, making it appropriate for video-line drivers, ADC input buffering, active filtering, and other circuits that require accurate signals across a broad frequency range. The THS4041CD provides a -3 dB bandwidth of 165 MHz and a slew rate of 400 V/µs. Because it is stable at all gains in both inverting and noninverting configurations, feedback design does not need to be restricted to unity gain. Its C-stable architecture allows it to drive capacitive loads, while typical output drive capability of 100 mA supports practical buffer and line-driver configurations. The device uses a conventional voltage-feedback signal path for high-speed amplification and filtering. Its combination of bandwidth, slew rate, unity-gain stability, and capacitive-load drive addresses common limitations of general-purpose operational amplifiers. The listed distortion figure of -75 dBc at 1 MHz shows that the amplifier can preserve signal fidelity in demanding high-frequency circuits without relying on a highly specialized output architecture. Typical uses include video-line driving, ADC input buffering, high-speed active filtering, signal conditioning, and communications or instrumentation signal paths. The same 8-pin SOIC footprint simplifies evaluation across the THS4041 family, while the 165 MHz bandwidth provides ample margin for signal-chain blocks that operate below the amplifier's small-signal limit. Circuit design should account for the amplifier's high slew rate and bandwidth because excessive capacitive loading, poorly placed compensation or feedback components, and long high-speed traces can create ringing or instability. Use the manufacturer's pin description and typical application circuits when assigning inputs, power, feedback, and decoupling connections, and verify the completed layout with appropriate test equipment. This page organizes the THS4041CD specifications, packaging information, commercially relevant purchasing details, same-package alternatives, and practical circuit guidance. It is intended to help engineers identify whether the amplifier's speed, stability, supply range, and SOIC footprint fit a specific design before committing to a component.

見積もり お問い合わせ