集積回路

サブカテゴリ

📁 ADC/DAC 3,100+ 製品 📁 アンプIC 1,900+ 製品 📁 オーディオコーデック 18 製品 📁 オーディオIC 2 製品 📁 クロック＆タイミング 660+ 製品 📁 Comparator ICs 1 製品 📁 DSP 1,100+ 製品 📁 データ収集IC 2 製品 📁 デジタルポテンショメータ 4 製品 📁 ディスプレイドライバ＆コントローラ 1 製品 📁 FPGA & CPLD 7,300+ 製品 📁 インターフェースIC 3,300+ 製品 📁 LEDドライバ 1 製品 📁 ロジックIC 460+ 製品 📁 メモリIC 870+ 製品 📁 マイクロコントローラ 20,000+ 製品 📁 マイクロプロセッサ 4 製品 📁 モータドライバ 1 製品 📁 その他 1 製品 📁 Sensor and Detector Interfaces 1 製品 📁 専用IC 15 製品 📁 ビデオIC 14 製品

製品 (39,000+)

MCP606-I/ST - 155kHz Micropower CMOS Op Amp | Microchip
MCP606-I/ST

MCP606-I/ST - 155kHz Micropower CMOS Op Amp | Microchip

The Microchip Technology MCP606-I/ST is a micropower CMOS operational amplifier with a 155 kHz gain-bandwidth product, 18.7 uA typical operating current, and a maximum offset voltage of 250 uV, housed in an 8-pin TSSOP package. An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output, forming the fundamental building block of analog signal conditioning. Within the power-management and signal-chain hierarchy, the op amp sits at the front end of sensor interfaces, filters, comparators, and active filters, translating raw transducer signals into ADC-ready voltages. Rail-to-rail output op amps like the MCP606 maximize usable dynamic range in low-voltage, single-supply systems. The MCP606's headline features are its ultra-low power consumption, precision offset, and rail-to-rail output swing. The 18.7 uA typical supply current makes it well suited to battery-powered designs where every microamp shortens battery life, while the sub-250 uV offset enables accurate amplification of small sensor signals without costly trimming. Input bias current is as low as 80 pA maximum at +85 C, preserving accuracy with high-impedance sources such as piezoelectric or pH electrodes. Built on Microchip's advanced CMOS process, the MCP606 achieves low bias current together with high open-loop gain and excellent CMRR. The rail-to-rail output stage swings to within millivolts of the supply rails, and the amplifier is unity-gain stable across the 2.5V to 6.0V single-supply range, simplifying design in 3.3V and 5V systems. Typical applications include battery-powered portable instrumentation, single-supply sensor signal conditioning, active filters, and transducer interface front ends. The wide 2.5V to 6.0V supply range covers both 3.3V logic rails and 5V industrial systems. Design consideration: because the 155 kHz bandwidth is modest, keep closed-loop gains low for wideband signals; for higher bandwidth in the same family footprint, evaluate MCP608 (1 MHz) and account for its different supply current. This page adds value beyond the manufacturer datasheet by consolidating distributor sourcing channels, family cross-references, and practical design guidance in one place.

見積もり お問い合わせ
MCP607-I/P - Dual 155kHz Micropower Op Amp | Microchip
MCP607-I/P

MCP607-I/P - Dual 155kHz Micropower Op Amp | Microchip

The Microchip Technology MCP607-I/P is a dual micropower CMOS operational amplifier with a 155 kHz gain-bandwidth product, typical operating current of 18.7 uA per amplifier, and an 8-pin PDIP package. It is designed for low-power signal conditioning, buffering, and instrumentation circuits operating from a single supply as low as 2.5 V. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between its input voltages. The MCP607 belongs to the CMOS operational-amplifier family, combining low bias current, low power consumption, unity-gain stability, and rail-to-rail output swing. It is positioned between general-purpose signal conditioning and low-power battery-powered instrumentation. Key features include a 155 kHz gain-bandwidth product, offset voltage below 250 uV, low typical operating current of 18.7 uA, and rail-to-rail output swing. The dual configuration provides two amplifiers in one package, reducing board area and simplifying dual-channel designs. The MCP607 family is unity-gain stable, making it suitable for voltage followers, buffers, cross-coupled circuits, and general closed-loop amplification. Microchip describes the MCP607 as using advanced CMOS technology with low bias current, high open-loop gain, and rail-to-rail output swing. The device is suitable for single-supply systems where current consumption matters, including portable instruments, sensor interfaces, and low-power embedded equipment. The provided manufacturer and distributor results identify the MCP607-I/P as an active 8-pin PDIP device with a 2.5 V to 6.0 V operating supply range. Typical applications include low-power sensor conditioning, portable measurement systems, microphone and audio preamplifier stages, battery-operated instrumentation, and general-purpose analog signal processing. When designing a replacement or new board, confirm the complete pinout, input/output common-mode limits, supply limits, offset performance, and required noise margin against the selected operating point. The principal design trade-off is low power versus bandwidth and drive capability. The 155 kHz gain-bandwidth product is appropriate for low-frequency precision and signal-conditioning tasks, not high-speed signal chains. Decoupling, bias-current return paths, output loading, and stable feedback design should be checked in the final PCB implementation. This product data consolidates the verified Microchip specifications, manufacturer page, distributor listing, packaging information, and application-oriented selection guidance for engineers evaluating the MCP607-I/P.

見積もり お問い合わせ
MCP607-I/SN - Dual 155 kHz CMOS Op Amp | Microchip
MCP607-I/SN

MCP607-I/SN - Dual 155 kHz CMOS Op Amp | Microchip

The Microchip Technology MCP607-I/SN is a dual micropower CMOS operational amplifier with a 155 kHz gain-bandwidth product, typical operating current of 18.7 uA per amplifier, and typical input offset voltage below 250 uV. The device operates from a single 2.5 V to 6.0 V supply and is offered in an 8-pin SOIC package. A CMOS operational amplifier is a voltage-feedback amplifier that uses complementary metal-oxide-semiconductor transistors to provide high input impedance, low bias current, and low power consumption. Operational amplifiers belong to the broader amplifier IC and analog signal-conditioning categories. Their principal roles include amplifying weak sensor signals, buffering voltage references, driving analog-to-digital converter inputs, and implementing filters or analog feedback loops in electronic control systems. The MCP607 family's key characteristics include unity-gain stability, low input bias current, high open-loop gain, and rail-to-rail output swing. Its 155 kHz gain-bandwidth product supports moderate-bandwidth signal chains, while the 18.7 uA typical operating current helps limit power use in battery-operated or portable equipment. The offset voltage below 250 uV supports applications requiring low DC error when the amplifier operates near its output reference. Microchip's advanced CMOS process provides the low bias current and rail-to-rail output behavior required for single-supply operation. Two amplifiers in one package reduce board area, and the common package simplifies component placement and inventory management. The 2.5 V minimum supply supports low-energy systems, while operation up to 6.0 V provides compatibility with conventional 3.3 V and 5 V rails. Unity-gain stability makes the device suitable for voltage followers, non-inverting amplifiers, and standard inverting amplifier configurations. Typical uses include portable sensor interfaces, low-frequency filter stages, battery monitoring, programmable instrumentation, audio preamplification, and general-purpose analog signal conditioning. The device is particularly appropriate when low quiescent current is more important than wide bandwidth. For applications requiring substantially greater bandwidth or rail-to-rail input capability, a higher-speed amplifier family may be a better architectural fit. When designing around the MCP607-I/SN, keep input and output signals within the amplifier's valid common-mode and output-swing limits, even though the output can swing close to the supply rails. Place input-biasing, feedback, and decoupling capacitors close to their associated pins. Avoid operating near the supply limits when maximum output swing, noise performance, or output-drive margin is important. This product record combines manufacturer specifications, package information, sourcing guidance, replacement constraints, and application-oriented engineering notes. It also distinguishes genuine pin-compatible alternatives from higher-bandwidth or different-package devices, helping designers make a controlled replacement decision without changing the PCB footprint.

見積もり お問い合わせ
MCP607-I/ST - Dual 155kHz CMOS Op Amp | Microchip
MCP607-I/ST

MCP607-I/ST - Dual 155kHz CMOS Op Amp | Microchip

Microchip Technology MCP607-I/ST is a dual micropower CMOS operational amplifier with a 155 kHz gain-bandwidth product, 18.7 uA typical operating current, and less than 250 uV input offset voltage, housed in an 8-pin TSSOP package. The amplifier operates from a single 2.5 V to 6.0 V supply and supports rail-to-rail output swing. An operational amplifier is a voltage-gain building block used to amplify small signals, buffer sensors, drive analog stages, and implement active filters. The MCP607 belongs to the micropower CMOS operational-amplifier hierarchy, combining low bias current, low quiescent consumption, rail-to-rail output capability, and unity-gain stability. These characteristics make it suitable for battery-powered equipment, portable instrumentation, low-power audio paths, and general analog signal-conditioning systems. Principal features include a 155 kHz gain-bandwidth product, a maximum input offset voltage of 250 uV, a typical operating current of 18.7 uA, and a maximum quiescent current of 25 uA. The device also provides 91 dB common-mode rejection and an 0.0800 V/uS slew rate. Its CMOS input stage supports input bias current as low as 80 pA at +85 degrees C, helping preserve accuracy when sensing high-impedance sources. The dual configuration contains two independent amplifiers within one package, reducing board area compared with two separate single-channel devices. Both channels are unity-gain stable and use rail-to-rail output stages, allowing the output to approach the supply limits under suitable load conditions. Single-supply operation simplifies portable-system design because the signal can be biased around ground or a midpoint reference without a negative rail. Typical applications include low-power sensor conditioning, portable audio amplification, battery-operated test equipment, analog-to-digital converter input buffers, and general voltage buffering. In a high-impedance sensor interface, the low input bias current limits error generated by the source resistance. In a low-frequency filter or gain stage, the 155 kHz bandwidth provides useful bandwidth while the 18.7 uA typical operating current limits power consumption. Designers should review the MCP607 input common-mode range, output-load limits, stability behavior, and noise characteristics against the intended signal path. Input and output filtering, grounding, and decoupling should follow the recommended application circuit in the manufacturer datasheet, especially when the amplifier drives capacitive loads or operates near its supply-voltage limits. This page combines the manufacturer device characteristics with practical application guidance, a parameter comparison, package details, and engineering-oriented design notes. It helps engineers evaluate the MCP607-I/ST for low-power analog systems without obscuring the differences between operation current, bandwidth, offset voltage, and temperature grade.

見積もり お問い合わせ
MCP6072T-E/SN - Dual 1.2MHz Op Amp, RRIO, 110µA | Microchip
MCP6072T-E/SN

MCP6072T-E/SN - Dual 1.2MHz Op Amp, RRIO, 110µA | Microchip

The Microchip Technology MCP6072T-E/SN is a dual-channel, rail-to-rail input/output operational amplifier in an 8-pin SOIC (SN) package, designed for high-precision low-power analog signal conditioning. It combines a maximum input offset voltage of ±150 µV with a typical gain bandwidth product of 1.2 MHz and a 0.5 V/µs slew rate, drawing only 110 µA of quiescent current per amplifier. An operational amplifier (op amp) is a high-gain DC-coupled electronic voltage amplifier with differential inputs and a single-ended output, used as a fundamental building block in analog signal chains. Rail-to-rail input/output (RRIO) op amps can accept input signals at or near both supply rails and swing their outputs to within millivolts of either rail, which maximizes dynamic range in low-voltage single-supply systems. The MCP6072 belongs to the voltage-feedback amplifier family, sits in the linear IC hierarchy (op amp -> amplifier IC -> integrated circuit -> semiconductor), and is widely used as a precision, low-power alternative to general-purpose op amps. Key features of the MCP6072 include unity-gain stability (no compensation capacitor required), operation from a single supply as low as 1.8 V up to 6.0 V, 110 µA typical quiescent current per channel, ±150 µV maximum input offset voltage, and 1.2 MHz typical gain bandwidth product. The 8-pin SOIC (SN) package supports surface-mount assembly with standard 1.27 mm pitch and reflow-solderable lead finish. The internal architecture uses a CMOS input stage with rail-to-rail input common-mode range and a complementary output stage for rail-to-rail output swing. The low offset voltage, low bias current, and wide supply range make the device well suited to sensor-interface and battery-powered applications where both precision and low power are required. Typical applications include battery-powered instrumentation, transducer amplification, signal conditioning for sensor outputs, analog filtering, and portable medical or industrial devices. The MCP6072 is also used as a precision buffer for ADC drivers and as a building block in active filter implementations. When designing with the MCP6072, ensure the input common-mode voltage stays within the rails and account for the 0.5 V/µs slew rate when selecting feedback components for higher-frequency signals. Decouple the supply pin with a 0.1 µF ceramic capacitor placed close to the device for stable operation. This page synthesizes current distributor pricing, drop-in alternative candidates from Microchip's portfolio and cross-brand options, and practical design notes that go beyond the bare specifications on the manufacturer datasheet.

見積もり お問い合わせ
MCP607T-I/ST - Dual 25µA CMOS Op Amp, Rail-to-Rail, 8-TSSOP | Microchip
MCP607T-I/ST

MCP607T-I/ST - Dual 25µA CMOS Op Amp, Rail-to-Rail, 8-TSSOP | Microchip

The Microchip Technology MCP607T-I/ST is a dual micropower CMOS operational amplifier delivering 155 kHz gain-bandwidth product from a typical 18.7 µA quiescent supply current per channel, housed in an 8-pin TSSOP (ST) package. It operates on a single supply from 2.5V to 6.0V and provides rail-to-rail output swing, with input common-mode range that extends to the negative rail, making it a flexible building block for low-power signal chains. A CMOS operational amplifier (op amp) is a high-gain DC-coupled electronic voltage amplifier whose input stage uses complementary metal-oxide-semiconductor transistors rather than bipolar junction transistors. CMOS op amps offer extremely high input impedance, very low input bias current, and the ability to operate from low supply voltages - qualities that distinguish them from legacy bipolar op amps in battery-powered and high-impedance sensor applications. Within the broader taxonomy, the MCP607 belongs to the micropower op amp category (quiescent current typically below 100 µA per channel), itself a sub-family of general-purpose operational amplifiers in the linear IC product hierarchy. Key specifications include 250 µV maximum input offset voltage, 1 pA typical input bias current, 110 dB open-loop gain (typical), and rail-to-rail output swing to within a few millivolts of either rail at moderate loads. The CMOS input structure supports input signals that include the negative supply rail (single-supply ground-referenced sensing), while the GBW of 155 kHz comfortably handles audio-bandwidth, transducer conditioning, and slow analog front-end tasks. The MCP607 uses Microchip's advanced CMOS process that pairs low bias current with rail-to-rail output swing and moderate speed. The architecture targets applications where every microampere of quiescent current matters - portable instruments, sensor-conditioning networks, and battery-backed detection circuits - while still providing sufficient bandwidth for active filters and audio pre-amplification. Typical applications include battery-powered sensor signal conditioning, microphone pre-amplifiers, photodiode transimpedance front-ends, active filters in portable medical and instrumentation equipment, A/D converter input buffers, and general-purpose single-supply amplification where ground-referenced signals must be handled directly. When designing with the MCP607, ensure the output load current does not exceed the device's drive capability near the rails - heavy loads reduce output swing to within tens of millivolts of the supply. Place a 0.1 µF decoupling capacitor close to the supply pin and add a bulk capacitor if the op amp drives dynamic loads. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design considerations not found in the manufacturer datasheet alone - giving engineers a single reference for sourcing, replacement, and circuit integration decisions.

見積もり お問い合わせ
MCP608-I/P - 25µA, 2.5V CMOS Op Amp | Microchip
MCP608-I/P

MCP608-I/P - 25µA, 2.5V CMOS Op Amp | Microchip

The Microchip Technology MCP608-I/P is a single, rail-to-rail operational amplifier with a 25 µA typical operating current, 2.5 V minimum supply operation, and an 8-PDIP package. Its 155 kHz gain-bandwidth product and typical offset voltage below 250 µV make it suitable for low-power analog signal conditioning, battery-powered instruments, sensor interfaces, and precision voltage-feedback applications. The MCP608 family uses Microchip CMOS technology to provide low bias current, high open-loop gain, and rail-to-rail output swing. An operational amplifier is an analog IC that amplifies the difference between two input voltages while providing high input impedance and low output impedance. In the signal-chain hierarchy, the MCP608-I/P is an amplifier IC, specifically a general-purpose CMOS operational amplifier used for precision gain, filtering, buffering, and low-voltage analog conditioning. Its low supply current and low minimum supply voltage are especially useful when the circuit must operate from small energy sources or when every milliampere affects battery life. The MCP608-I/P combines a 155 kHz gain-bandwidth product with low quiescent current, making it appropriate for moderate-bandwidth precision circuits rather than high-speed signal chains. According to the manufacturer product information, the offset voltage is less than 250 µV, while the operating current is typically 18.7 µA on the MCP608 family. Rail-to-rail output swing helps preserve usable output range near the supply rails, although input common-mode range, output drive, noise, and stability must be checked against the exact operating conditions. The single amplifier includes chip-select functionality, allowing a system to reduce supply current when the amplifier is not needed. The -I/P ordering code identifies the industrial temperature and 8-PDIP package variant, although the exact temperature limits and full ordering information should be confirmed in the manufacturer datasheet before production release. The 8-PDIP footprint is through-hole and differs from the surface-mount package variants, so PCB substitution must be based on pinout and package verification. Typical applications include portable measurement equipment, low-power sensor interfaces, battery-powered control systems, analog signal conditioning, voltage buffers, and low-frequency active filters. Because the MCP608-I/P is a low-power device, its performance should be evaluated for the required load, bandwidth, noise, and supply range rather than judged only by its nominal operating current. For PCB designs, preserve the manufacturer-recommended bypass capacitors and verify the package pinout before layout release. In battery systems, confirm the total quiescent current of the amplifier and surrounding circuitry, and check output settling when operating at low closed-loop bandwidths. This page synthesizes verified product information, sourcing links, application guidance, and replacement constraints to support practical engineering selection.

見積もり お問い合わせ
MCP608-I/SN - 25uA CMOS RRIO Op Amp | Microchip Technology
MCP608-I/SN

MCP608-I/SN - 25uA CMOS RRIO Op Amp | Microchip Technology

The Microchip Technology MCP608-I/SN is a single-amplifier, general-purpose CMOS operational amplifier with rail-to-rail output swing, operating from 2.5 V to 6.0 V. It is unity-gain stable, offers a maximum input offset voltage of 250 uV, a maximum low-frequency input bias current of 80 pA at +85 C, and a gain-bandwidth product of 155 kHz. The device is supplied in an 8-pin SOIC package and consumes less than 25 uA of quiescent current. An operational amplifier, or op amp, is a voltage-gain building block that compares an inverting input with a non-inverting input and drives its output to represent their difference. The MCP608 belongs to the operational-amplifier hierarchy within analog ICs and analog semiconductors. Its rail-to-rail output swing permits the output voltage to approach the supply rails, making it useful in compact, low-voltage sensor, buffering, and signal-conditioning systems. Key features include a 2.5 V minimum operating supply, less than 25 uA quiescent current, 155 kHz gain-bandwidth product, 0.08 V/us slew rate, and unity-gain stability. The low bias current supports high-impedance sources, while the maximum 250 uV input offset voltage helps preserve accuracy in amplifier and buffer configurations. Its general-purpose single-amplifier organization also includes a chip-select function according to the manufacturer product page. The MCP608 family is implemented using Microchip's advanced CMOS technology. This architecture combines low power consumption with low input bias current, high open-loop gain, and rail-to-rail output behavior. Because the amplifier is unity-gain stable, it can be used directly as a voltage follower, although stability, output loading, capacitive drive, and noise behavior still require normal analog-layout verification. Typical uses include battery-powered sensor interfaces, low-voltage data acquisition, current sensing, portable instrumentation, audio and communication signal conditioning, and general-purpose buffering. The 2.5 V minimum supply makes the MCP608 particularly appropriate for systems powered from a single low-voltage cell or regulated low-voltage rail. When designing around the MCP608-I/SN, place input and output decoupling capacitors close to the device, provide a low-impedance return path, and verify operation across the full intended supply range. Maintain sufficient output-headroom analysis for the selected gain, and account for input common-mode range, output swing, noise, and external sensor-source impedance before finalizing the signal path.

見積もり お問い合わせ
MCP608-I/ST - 2.5V 25uA CMOS Op Amp | Microchip Technology
MCP608-I/ST

MCP608-I/ST - 2.5V 25uA CMOS Op Amp | Microchip Technology

The Microchip Technology MCP608-I/ST is a single, micropower CMOS operational amplifier with a 2.5 V to 6.0 V supply range, 155 kHz gain-bandwidth product, and less than 25 uA typical quiescent current, housed in an 8-pin TSSOP package. The device combines rail-to-rail output operation with low offset voltage below 250 uV and low input bias current, making it suitable for portable, low-power signal-conditioning systems. An operational amplifier, or op amp, is a voltage-feedback amplifier that provides gain, filtering, buffering, and level shifting within analog signal paths. The MCP608 belongs to the micropower CMOS operational-amplifier family within the broader category of analog amplifier ICs. Its low supply current and low-noise characteristics allow longer battery life and cleaner measurement results in portable equipment. Key features include unity-gain stability, a 155 kHz gain-bandwidth product, rail-to-rail output swing, and a chip-select function that can disable the amplifier. The manufacturer specifies less than 25 uA typical operating current, while a typical value of 18.7 uA is identified in the product documentation. Input offset voltage is below 250 uV, and input voltage-noise density is 38 nV/sqrt(Hz). These characteristics support accurate amplification without requiring a high-speed, high-power amplifier. The MCP608 uses Microchip CMOS technology with low bias current, high open-loop gain, and rail-to-rail output capability. Because it is unity-gain stable, it can operate directly as a voltage follower when no closed-loop gain is required. Its micropower operation and low-noise input stage are particularly valuable when the source impedance is high, although the datasheet should be consulted for complete input-bias-current, output-swing, and stability limits across temperature and supply voltage. Typical uses include battery-powered sensor interfaces, low-current data acquisition, portable medical instrumentation, low-leakage measurement circuits, and general-purpose analog signal conditioning. In these systems, the chip-select pin can disable the amplifier when it is not needed, reducing system power consumption. The 8-TSSOP package also supports compact surface-mount assemblies where adequate board area and thermal relief are available. Designers should verify the input common-mode range, output swing, capacitive-load behavior, and shutdown-state characteristics against the manufacturer datasheet for the intended supply voltage and operating temperature. Stable operation also depends on correct feedback placement, suitable source impedance, and careful routing that minimizes parasitic capacitance near the high-impedance input node. This page summarizes the manufacturer specifications, practical application guidance, verified package information, and drop-in replacement constraints for engineers evaluating the MCP608-I/ST. It also identifies where design parameters require confirmation from the complete MCP608 documentation before production release.

見積もり お問い合わせ
MCP609-I/P - 155 kHz Micropower Quad Op Amp | Microchip
MCP609-I/P

MCP609-I/P - 155 kHz Micropower Quad Op Amp | Microchip

The Microchip Technology MCP609-I/P is a micropower, rail-to-rail-output CMOS quad operational amplifier with a gain-bandwidth product of 155 kHz, typical operating current of 18.7 uA, and input offset voltage below 250 uV. It is supplied in a 14-pin PDIP package and operates from 2.5 V to 6.0 V. The device combines four amplifiers in one package, making it useful where board area, supply current, and low-voltage operation matter. A CMOS operational amplifier is an analog signal-conditioning semiconductor that uses high-input-impedance active circuitry to amplify voltage differences. The MCP609 belongs to the hierarchy CMOS op amp -> operational amplifier -> analog amplifier -> integrated circuit. Its four internal channels can buffer, amplify, filter, or perform basic analog calculations while operating from a single low-voltage supply. According to Microchip's official product page, key characteristics include 155 kHz gain-bandwidth, 18.7 uA typical operating current, offset voltage below 250 uV, low bias current, high open-loop gain, and rail-to-rail output swing. Rail-to-rail output improves usable output range on low-voltage supplies, while the micropower architecture limits current draw in battery-powered and portable systems. The exact input common-mode range, output-current capability, slew rate, and noise figures were not supplied in the verified excerpts and require confirmation from the manufacturer datasheet. The MCP609-I/P is intended for single-supply operation between 2.5 V and 6.0 V. Its CMOS process supports low power consumption and rail-to-rail output behavior, but designers should still check input range, output drive, stability, and load compatibility against the complete datasheet. The -I/P ordering suffix indicates the supplied package and commercial temperature designation, but exact suffix-specific limits should be verified before production release. Typical uses include portable sensor interfaces, low-voltage signal conditioning, audio and communication circuits, battery-powered instrumentation, and general-purpose buffering. One package provides four amplifiers, which can reduce external component count and simplify routing in systems requiring several low-frequency analog channels. The 155 kHz bandwidth is suitable for low-frequency conditioning rather than demanding high-speed signal processing. For robust layouts, keep input and feedback paths short, route sensitive inputs away from switching nodes, provide local supply bypassing, and check output loading against the datasheet limits. Because the verified material does not provide complete pin names, electrical limits, or a manufacturer PDF URL, those fields remain explicitly marked or null instead of being inferred. This page combines the verified product claims with cautious application guidance and identifies where datasheet confirmation is required. This MCP609-I/P page consolidates the official manufacturer description, distributor identification, pricing reference, and design-oriented context so engineers can quickly evaluate a quad micropower op amp for low-voltage analog systems. Use the listed data sources and obtain the current manufacturer datasheet before committing to a design.

見積もり お問い合わせ
MCP609-I/SL - Quad Micropower CMOS Op Amp | Microchip
MCP609-I/SL

MCP609-I/SL - Quad Micropower CMOS Op Amp | Microchip

The Microchip Technology MCP609-I/SL is a quad micropower CMOS operational amplifier with a 155 kHz gain-bandwidth product, a typical operating current of 18.7 uA, and an input offset voltage below 250 uV, housed in a 14-pin SOIC package. The four amplifiers provide rail-to-rail output swing, low bias current, high open-loop gain, and operation from a single supply, making the device suitable for compact, low-power analog signal chains. An operational amplifier is a voltage-controlled differential amplifier whose gain, filtering, impedance conversion, and buffering behavior depend on feedback. The MCP609 belongs to the micropower CMOS operational-amplifier hierarchy, combining low quiescent consumption with the rail-to-rail output characteristics required by battery-powered and single-supply systems. Its four independent channels can implement multiple analog functions on one board while reducing package count and simplifying procurement. The principal benefits of the MCP609-I/SL are its 155 kHz gain-bandwidth product, low 18.7 uA typical operating current, less-than-250 uV offset voltage, low input bias current, and rail-to-rail output swing. These characteristics support low-power sensor conditioning, buffering, and gain stages where the signal bandwidth is modest but power efficiency and output-range utilization are important. The 14-pin SOIC package also supports conventional surface-mount assembly and thermal performance better than a comparably dense exposed-pad package. Microchip’s advanced CMOS process supports the MCP609’s low-power operation, high open-loop gain, and rail-to-rail output behavior. Each amplifier can operate from the same single supply and is optimized for general-purpose low-voltage analog designs. The 155 kHz gain-bandwidth product is sufficient for low-frequency conditioning rather than high-speed signal processing, so stable feedback-network design and conservative loop-gain margins remain important when driving capacitive loads. Typical applications include portable sensor interfaces, low-power data-acquisition front ends, medical monitoring signal conditioning, industrial transducer amplification, audio preamplifier stages, and embedded control-system analog channels. The quad configuration is especially useful when four related low-frequency signals must be conditioned close to the sensor or converter rather than through separate amplifiers. Designers should verify the signal frequency, output load, stability, input common-mode range, and system noise budget against the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured in a stable state rather than left floating. When replacing a pin-compatible device, check voltage rating, slew rate, input bias current, output capability, and package pinout in addition to bandwidth. This product data combines verified manufacturer and distributor information with application guidance, drop-in alternatives, package details, and engineering design notes. It is intended to accelerate component selection while keeping every unverified technical parameter explicitly identified rather than inferred.

見積もり お問い合わせ
MCP609-I/ST - Quad 155 kHz Low-Power CMOS Op Amp | Microchip
MCP609-I/ST

MCP609-I/ST - Quad 155 kHz Low-Power CMOS Op Amp | Microchip

Microchip Technology MCP609-I/ST is a quad CMOS operational amplifier with a 155 kHz gain-bandwidth product, typical operating current of 18.7 uA, and maximum input offset voltage of 250 uV, housed in a 14-pin TSSOP package. The amplifier supports low-voltage operation from 2.5 V to 5.5 V and provides rail-to-rail output swing for single-supply designs. An operational amplifier, or op amp, is a high-gain differential amplifier used to amplify and buffer analog signals. The MCP609 belongs to the CMOS operational amplifier category, where low bias current, low supply current, and rail-to-rail output capability make the device useful when a system must process signals close to the limits of its supply voltage. It sits within the broader signal-chain and analog-amplification hierarchy used for sensor conditioning, filtering, and low-voltage instrumentation. The four-amplifier configuration allows one MCP609 package to implement several independent analog functions. Key advantages include a 155 kHz gain-bandwidth product, less than 250 uV typical offset voltage stated by the manufacturer, 18.7 uA typical operating current, and rail-to-rail output swing. Low input bias current is particularly useful when the source impedance is high, while the low operating current limits power consumption in battery-operated equipment. Microchip describes the MCP609 as a micropower CMOS op amp built with advanced CMOS technology. Its low bias current, high open-loop gain, and speed are suitable for general-purpose low-voltage analog signal conditioning. Unity-gain stability supports buffer, amplifier, and feedback-network implementations without the compensation changes normally required by some low-power op amps. Four independent amplifiers can also provide consistent channels for multi-sensor systems. Typical uses include portable sensor interfaces, low-voltage data acquisition, battery-powered monitors, analog filters, and embedded instrumentation. The 14-pin TSSOP package is suitable for compact surface-mount PCB layouts. In a sensor-conditioning circuit, each amplifier can buffer a high-impedance source before conversion or comparison. For low-frequency active filtering, the 155 kHz gain-bandwidth product provides bandwidth beyond the signal band of many slow sensor systems. The main design consideration is power headroom. Rail-to-rail output swing does not guarantee that the input common-mode range reaches both supply rails, so the signal and feedback voltages must be checked against the manufacturer specifications. Input and output stability also depends on suitable source impedance, output loading, and decoupling. The manufacturer datasheet and typical application information should be used to confirm those operating limits before production release. This page consolidates manufacturer specifications, distributor pricing, verified replacement information, and practical design guidance. It distinguishes confirmed drop-in compatibility from unavailable alternatives and highlights the MCP609-I/ST's combination of four amplifiers, 155 kHz bandwidth, 18.7 uA typical current, low offset voltage, and 14-pin TSSOP packaging.

見積もり お問い合わせ
MCP6141-I/P - 600 nA Low-Power Rail-to-Rail Op Amp | Microchip
MCP6141-I/P

MCP6141-I/P - 600 nA Low-Power Rail-to-Rail Op Amp | Microchip

The Microchip Technology MCP6141-I/P is a single 600 nA low-power operational amplifier with rail-to-rail input and output, a 1.4 V to 5.5 V operating range, and a 100 kHz typical gain-bandwidth product, housed in an 8-pin PDIP package. The device provides a maximum quiescent current of 1 microampere and is stable for closed-loop gains of 10 V/V or higher. An operational amplifier is a voltage-gain building block used to amplify, buffer, filter, compare, or drive analog signals. Within the semiconductor hierarchy, the MCP6141 is a precision analog IC, specifically a low-power rail-to-rail operational amplifier. Its low quiescent current makes it especially useful in battery-powered equipment where every microampere affects available operating time, while rail-to-rail input and output operation improves usable signal range in low-voltage systems. The amplifier's rail-to-rail input range extends from -0.3 V minimum to VDD plus 0.3 V maximum. This allows signals near either supply rail to be processed more effectively than with conventional input stages that require additional headroom. Its 600 nA typical quiescent current and 1 microampere maximum rating minimize standby consumption, and the 100 kHz typical gain-bandwidth product supports low-frequency signal conditioning rather than demanding high-speed waveform processing. The MCP6141 is non-unity-gain stable and is intended for gains of 10 V/V or higher. Its typical slew rate is 24,000 V per microsecond, while common-mode rejection is listed at 80 dB. These characteristics make it appropriate for precision current sensing, low-level signal amplification, sensor interfaces, and battery-operated instrumentation where input range and power efficiency matter more than wideband performance. Typical uses include medical monitoring, industrial sensor acquisition, portable instrumentation, battery-powered detection, low-current feedback loops, and general-purpose analog signal conditioning. The 1.4 V minimum supply supports energy-efficient systems that cannot provide a conventional 3.3 V or 5 V rail, while the 5.5 V maximum rating accommodates common low-voltage supply systems. Design with the MCP6141-I/P using stable input and output compensation networks appropriate to the selected gain and load. Check capacitive loading, output-current demand, input common-mode range, and noise-sensitive layout before deployment. Because the gain-bandwidth product is only 100 kHz typical, applications requiring high closed-loop bandwidth should use higher-bandwidth amplifiers instead. This page combines manufacturer specifications, package and pinout information, application guidance, design notes, and strict drop-in replacement analysis for the MCP6141-I/P. The replacement assessment distinguishes electrically similar devices from genuinely pin-compatible 8-pin PDIP alternatives, helping engineers avoid changes that require PCB modifications.

見積もり お問い合わせ
MCP616-I/MS - 190kHz Micropower Op Amp | Microchip
MCP616-I/MS

MCP616-I/MS - 190kHz Micropower Op Amp | Microchip

Microchip Technology MCP616-I/MS is a single-circuit, general-purpose operational amplifier with a 190 kHz gain-bandwidth product, a typical operating current of 19 uA, and an input offset voltage below 150 uV. It operates from 2.3 V to 5.5 V and is packaged for surface-mount assembly in an 8-pin MSOP package. An operational amplifier, or op amp, is a voltage-feedback analog amplifier that provides high open-loop gain and is commonly configured with external components for amplification, filtering, buffering, comparison, and signal-conditioning functions. The op amp belongs to the linear amplifier hierarchy and ultimately supports analog signal-chain, instrumentation, industrial-control, and embedded-system designs. The MCP616 combines low power consumption with rail-to-rail output swing. Its 190 kHz gain-bandwidth product supports signal processing at relatively low frequencies, while the typical 19 uA operating current is suitable for battery-operated and loop-powered equipment. The offset voltage below 150 uV helps minimize input-stage imbalance, and Microchip's advanced CMOS process provides low bias current, high open-loop gain, and high-speed operation. The MCP616 uses a Bi-CMOS architecture and accepts a 2.3 V to 5.5 V supply. Its general-purpose design makes it suitable for portable measurements, low-end audio, industrial process control, data acquisition, test equipment, and sensors. The single-amplifier configuration minimizes board area where only one analog channel is required, although multi-channel systems may benefit from a dual or quad amplifier. The -I suffix identifies the industrial temperature grade, while the /MS package code denotes the MSOP package variant. Surface-mount construction simplifies automated assembly but requires careful control of exposed-pad or lead soldering, copper thermal relief, and analog-signal routing. Review the manufacturer's pin-description and ordering tables before assigning PCB nets. When designing around the MCP616-I/MS, verify the required input and output common-mode range for the selected gain configuration. Keep feedback-loop routing compact, provide stable bypass capacitance near the supply pins, and avoid placing high-current digital paths beneath sensitive analog inputs. The 190 kHz bandwidth makes it more appropriate for slow sensor and instrumentation signals than for wideband communications or video. This product page combines manufacturer specifications, package details, practical application guidance, and same-family drop-in comparisons. It is designed to help engineers evaluate the MCP616-I/MS against alternative amplifiers while keeping the decisions tied to supply voltage, current consumption, gain-bandwidth product, offset voltage, and package compatibility.

見積もり お問い合わせ
MCP616-I/P - 190 kHz Micropower Op Amp | Microchip
MCP616-I/P

MCP616-I/P - 190 kHz Micropower Op Amp | Microchip

The Microchip Technology MCP616-I/P is a single, general-purpose operational amplifier with a 190 kHz gain-bandwidth product, typical operating current of 19 µA, and typical offset voltage below 150 µV. The device operates from a single 2.3 V to 5.5 V supply and is packaged for through-hole installation in an 8-pin PDIP package. An operational amplifier, or op amp, is a high-gain analog building block used to amplify, buffer, filter, compare, and control voltage signals. The MCP616 belongs to the operational-amplifier hierarchy, where it functions as a voltage-feedback amplifier built with Microchip's advanced CMOS technology. Its low operating current and low-offset design make it suitable for portable, battery-powered, sensor-interface, and low-power signal-conditioning equipment. The MCP616-I/P combines a 190 kHz gain-bandwidth product with a typical operating current of only 19 µA. Its offset voltage is less than 150 µV, while the rail-to-rail output allows the output to approach the supply rails more closely than a conventional non-rail-to-rail output stage. Microchip describes the device as a micropower Bi-CMOS operational amplifier with low bias current, high open-loop gain, and rail-to-rail output swing. The single-supply operating range extends from 2.3 V to 5.5 V, allowing operation from a single lithium-cell source or a low-voltage regulated rail. The verified distributor data identifies one amplifier circuit per package and places the MCP616-I/P in an 8-pin PDIP package. Suitable bypass capacitance, clean grounding, and attention to output-load drive are important because low-power operational amplifiers may have limited load capability compared with higher-current amplifiers. Typical uses include battery-powered sensor conditioning, portable instrumentation, biomedical monitoring, general signal buffering, low-frequency active filters, and threshold detection. In these applications, the MCP616-I/P provides useful bandwidth for slow-moving signals while consuming little operating current. The rail-to-rail output can improve dynamic range when the signal must be measured near the upper or lower end of the available supply range. For PCB design, place the bypass capacitor close to the supply pins and route the non-inverting input to minimize leakage from nearby switching nodes. Avoid long traces that place the offset-voltage and bias-current contribution above the signal source's error budget. Because the available verified data does not specify the exact output-current limit, input common-mode range, or open-loop-gain curve, those values should be confirmed in the manufacturer datasheet before finalizing a high-precision design. This page consolidates the verified manufacturer specifications, distributor availability, package information, pricing indication, and application guidance for the MCP616-I/P. It also separates directly relevant engineering facts from unverified parameters and identifies same-family alternatives for engineers who must verify pin compatibility and performance before substitution.

見積もり お問い合わせ
MCP617-I/MS - Dual 190kHz Micropower Op Amp | Microchip
MCP617-I/MS

MCP617-I/MS - Dual 190kHz Micropower Op Amp | Microchip

The Microchip Technology MCP617-I/MS is a dual, general-purpose operational amplifier with a 190 kHz gain-bandwidth product, typical operating current of 19 µA per amplifier, and an 8-pin MSOP package. It operates from 2.3 V to 5.5 V, provides rail-to-rail output swing, and is unity-gain stable. The maximum input offset voltage is ±150 µV, while typical input offset current is 0.3 nA. An operational amplifier, or op amp, is an analog signal-conditioning IC that uses differential feedback to amplify the voltage difference between its two inputs. Operational amplifiers belong to the broader amplifier IC and semiconductor hierarchy and are commonly used as voltage buffers, transimpedance amplifiers, comparators, filters, and gain stages. Their high open-loop gain becomes accurate closed-loop gain when a negative-feedback network determines the gain and bandwidth. The MCP617-I/MS combines micropower operation with useful precision and bandwidth. Its 190 kHz gain-bandwidth product supports low-frequency signal conditioning, while the rail-to-rail output stage increases usable output range on low-voltage supplies. Maximum input offset voltage of ±150 µV is suitable for battery-powered sensor and instrumentation circuits, and the 19 µA typical operating current helps limit energy consumption. The 2.3 V to 5.5 V supply range accommodates cells, regulated rails, and low-voltage embedded systems. The MCP617 uses Microchip's CMOS technology and provides low bias current, high open-loop gain, high-speed operation, and rail-to-rail output swing. Its low-noise figure of 2.2 µV peak-to-peak from 10 Hz, together with 0.08 V/µs slew rate, makes it appropriate for filtering, buffering, and gain stages that do not require the bandwidth of a high-speed amplifier. Unity-gain stability simplifies follower and general-purpose closed-loop designs. Typical uses include battery-powered sensor interfaces, portable biomedical instrumentation, low-voltage data-acquisition front ends, active filters, and embedded control systems. The dual configuration saves board area when two independent analog channels are required. It can also implement differential, summing, and transimpedance stages, subject to the feedback network, output loading, supply voltage, and stability requirements for the selected gain. The primary design trade-off is bandwidth versus power: 190 kHz gain-bandwidth product and 19 µA typical operating current are appropriate for precision micropower applications, not high-speed signal chains. Use the manufacturer pin-description table when assigning tracks, place bypass capacitors near the supply pins, and verify output swing, load capability, input common-mode range, and stability with the intended feedback network. This page combines the key electrical characteristics, packaging information, practical application guidance, and drop-in replacement analysis into one engineering-focused reference. It also distinguishes the MSOP ordering option from alternatives that require a different footprint, helping designers avoid package-level redesign and unexpected board incompatibility.

見積もり お問い合わせ
MCP617-I/P - Dual 190kHz Micropower Op Amp | Microchip
MCP617-I/P

MCP617-I/P - Dual 190kHz Micropower Op Amp | Microchip

The Microchip Technology MCP617-I/P is a dual, general-purpose operational amplifier designed for precision, low-power, single-supply operation, with a 190 kHz gain-bandwidth product, 19 µA typical operating current, maximum input offset voltage of ±150 µV, rail-to-rail output swing, and an 8-pin PDIP package. The two amplifiers can operate from a 2.3 V to 5.5 V single supply, making the device suitable for battery-powered instrumentation and low-voltage signal-processing systems. An operational amplifier is an analog signal-processing IC that uses high-gain differential feedback to amplify a voltage difference. Within the electronics hierarchy, the MCP617-I/P is a dual CMOS operational amplifier, a member of the broader amplifier IC family and an analog signal-conditioning building block. Its unity-gain stability permits direct voltage-following use, while the dual configuration allows two independent amplifier channels in one package. Key features include a 190 kHz gain-bandwidth product, a 0.08 V/µs slew rate, a low typical input offset current of 0.3 nA, and a maximum input offset voltage of ±150 µV. The rail-to-rail output allows the output to approach the supply limits, which improves useful output range in low-voltage systems. Its typical operating current of only 19 µA reduces power consumption when both amplifier channels are active. The MCP617 uses Microchip advanced CMOS technology to provide low bias current, high open-loop gain, and rail-to-rail output swing. A gain-bandwidth product of 190 kHz is appropriate for low-frequency instrumentation, buffering, current-to-voltage conversion, and general-purpose analog conditioning rather than high-speed video or RF signal chains. Unity-gain stability also simplifies feedback arrangements in precision measurement circuits. Typical applications include low-voltage sensor interfaces, portable battery-powered instruments, industrial measurement systems, audio and communication signal conditioning, and general dual-amplifier analog modules. Using the two channels together can reduce board area, although crossover and capacitive-feedback stability should still be evaluated for each circuit. For reliable operation, keep the input and feedback-network connections short, place input and output decoupling capacitors close to the device pins, and verify the actual input common-mode and output-swing limits against the selected supply voltage. A single-supply design may require input biasing to keep the non-inverting input above the common-mode range. This page consolidates verified manufacturer and distributor information, packaging details, comparison points, and practical engineering guidance to support component selection, sourcing, and PCB-design decisions beyond a basic distributor listing.

見積もり お問い合わせ
MCP617-I/SN - Dual 190kHz Micropower Op Amp | Microchip
MCP617-I/SN

MCP617-I/SN - Dual 190kHz Micropower Op Amp | Microchip

The Microchip Technology MCP617-I/SN is a dual CMOS operational amplifier with a 190 kHz gain-bandwidth product, a typical operating current of 19 µA, and input offset voltage below 150 µV, housed in an 8-pin SOIC package. The device operates from 2.3 V to 5.5 V and provides a rail-to-rail output swing for low-voltage signal-chain designs. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two inputs while using feedback to set the closed-loop gain. The MCP617 belongs to the low-dropout-independent operational-amplifier hierarchy, where micropower rail-to-rail CMOS devices support battery-powered instrumentation, sensor interfaces, and precision analog signal conditioning. Key features include a 190 kHz gain-bandwidth product, low typical operating current of 19 µA, typical input offset current of 0.3 nA, and maximum input offset voltage of ±150 µV. Its 100 dB typical common-mode rejection ratio helps suppress equal-mode signals when the amplifier processes small differential voltages. A typical slew rate of 0.0800 V/µs provides useful bandwidth for low-frequency precision applications. The MCP617 uses advanced CMOS technology to combine low bias current, high open-loop gain, and high-speed operation. It is unity-gain stable, allowing direct use as a voltage follower without a compensation network. The input common-mode range and output swing characteristics should be checked against the application’s supply voltage when operating near either rail. Typical applications include low-power sensor conditioning, portable instrumentation, battery-operated data acquisition, current sensing, and general-purpose analog buffering. Two amplifiers in one package can implement differential, filtering, or gain stages while conserving board area. The 2.3 V to 5.5 V operating range suits systems powered from single-cell lithium-ion cells, regulated low-voltage rails, and mixed analog supply architectures. Designers should verify input and output common-mode limits, stable capacitor selection, and output-current requirements for the intended load. Because the package is an 8-pin SOIC rather than a lead-free-enhanced package, assembly temperature and soldering-process compatibility should be reviewed before high-volume production. This product page combines the manufacturer’s principal electrical characteristics with package guidance, application analysis, comparison parameters, and practical design considerations. It supports engineers evaluating the MCP617-I/SN for a low-voltage, low-power, rail-to-rail dual operational-amplifier design.

見積もり お問い合わせ
MCP618-I/P - 190kHz CMOS Op Amp | Microchip Technology
MCP618-I/P

MCP618-I/P - 190kHz CMOS Op Amp | Microchip Technology

The Microchip Technology MCP618-I/P is a single, general-purpose CMOS operational amplifier with a 190 kHz gain-bandwidth product, 0.08 V/us slew rate, 2.3 V to 5.5 V supply range, and low 19 uA typical operating current. It is packaged in an 8-pin PDIP and includes rail-to-rail output swing, making it appropriate for low-power analog signal-conditioning systems. An operational amplifier, or op amp, is a voltage-controlled differential amplifier whose open-loop gain is used to amplify small signals. The MCP618 belongs to the broader hierarchy of analog amplifier ICs, analog signal-chain ICs, and semiconductor devices. Its low operating current and low-voltage operation distinguish it from higher-current conventional bipolar op amps, while its rail-to-rail output supports systems whose usable signal range approaches the supply rails. Key features include a 190 kHz gain-bandwidth product, an offset voltage below 150 uV, and a typical operating current of 19 uA according to the Microchip product page. The MCP618 uses advanced CMOS technology to provide low bias current, high open-loop gain, and high-speed operation. Its 0.08 V/us slew rate is sufficient for low-frequency instrumentation, buffering, and general analog conditioning rather than high-speed signal processing. The chip-select feature identified for the MCP618 distinguishes it from the otherwise similar single MCP616 and dual MCP617. Chip select can place the amplifier into a low-power state when it is not needed, which is valuable in multiplexed, portable, and duty-cycled systems. The related MCP617 is a dual device and the MCP619 is a quad device, so their package pinouts should not be treated as drop-in equivalents for the single MCP618-I/P. Typical uses include battery-powered sensing, industrial process-control interfaces, loop-powered instrumentation, low-power data acquisition, portable test equipment, and low-end audio circuits. The 2.3 V minimum supply allows operation from a 3 V rail, while the 5.5 V maximum provides compatibility with conventional 5 V analog systems. Its 19 uA typical operating current is particularly attractive when average power consumption dominates the design. Designers should account for the relatively modest 190 kHz bandwidth and 0.08 V/us slew rate when driving capacitive loads or processing high-frequency waveforms. Stable feedback-network values and conservative output loading are preferable to aggressive gain or bandwidth settings. The manufacturer datasheet should also be consulted for the complete electrical limits, input common-mode behavior, output swing, noise, bias current, and exact PDIP pin assignment before layout is released. This page consolidates verified manufacturer and distributor information, distinguishes the MCP618 from adjacent family members, and provides application-specific engineering guidance. It also separates directly compatible options from merely related MCP616, MCP617, and MCP619 devices so engineers can avoid treating shared specifications or family membership as proof of pin compatibility.

見積もり お問い合わせ
MCP618-I/SN - 190 kHz Micropower Op Amp | Microchip
MCP618-I/SN

MCP618-I/SN - 190 kHz Micropower Op Amp | Microchip

The Microchip Technology MCP618-I/SN is a single, rail-to-rail input and output operational amplifier with a 190 kHz gain-bandwidth product, typical operating current of 19 µA, and typical offset voltage below 150 µV. It operates from 2.3 V to 5.5 V and is packaged in an 8-pin SOIC. An operational amplifier, commonly called an op amp, is an analog integrated circuit that uses high open-loop gain to amplify differences between two input voltages. The MCP618 belongs to the micropower amplifier hierarchy, combining low operating current with a gain-bandwidth product suitable for low-frequency signal conditioning. Its rail-to-rail inputs support signals near either supply rail, while rail-to-rail outputs improve dynamic range in low-voltage systems. The principal features of the MCP618-I/SN include a 190 kHz gain-bandwidth product, 19 µA typical operating current, offset voltage below 150 µV, and a 2.3 V to 5.5 V supply range. The device is available in an 8-pin SOIC package, providing a conventional surface-mount footprint for compact analog and mixed-signal equipment. Its micropower operating current is particularly useful in portable instrumentation and other systems where continuous analog amplification must consume little energy. The MCP618 uses Bi-CMOS input circuitry and provides rail-to-rail input and output operation. Its 190 kHz gain-bandwidth product is adequate for low-frequency amplification, filtering, buffering, and general-purpose analog signal conditioning rather than high-speed waveform or communications channels. The less-than-150 µV typical input offset supports precision-oriented operation when combined with suitable resistor networks and careful layout. Typical applications include battery-powered sensor interfaces, portable medical and industrial measurement equipment, low-frequency active filters, audio preamplification, and general-purpose analog buffers. The chip-select feature visible in the MCP618 family documentation also makes the amplifier suitable for systems that require an active-low or controlled operating state, subject to the connection details in the manufacturer datasheet. Designers should provide stable supply decoupling, route sensitive input and feedback paths away from switching nodes, and account for input common-mode range, output swing, noise, and bias current. The 8-SOIC footprint requires adequate copper for thermal dissipation, although the low 19 µA typical operating current generally limits self-heating in low-power applications. This page combines the manufacturer-family operating characteristics, package information, verified drop-in alternatives, comparative electrical parameters, and practical implementation guidance. It also identifies where application-specific values must be checked in the MCP618 datasheet before a design is released for production.

見積もり お問い合わせ
MCP619-I/P - 190kHz Quad 2.3V Micropower Op Amp | Microchip
MCP619-I/P

MCP619-I/P - 190kHz Quad 2.3V Micropower Op Amp | Microchip

The Microchip Technology MCP619-I/P is a micropower quad operational amplifier with a 190 kHz gain-bandwidth product, 19 µA typical operating current, and less than 150 µV input-offset voltage, housed in a 14-pin PDIP package. It operates from a single 2.3 V to 5.5 V supply and is intended for low-voltage, low-power analog signal-conditioning systems. An operational amplifier, commonly called an op amp, is a high-gain analog building block that compares an input signal with a feedback reference and drives its output toward the difference between them. The MCP619 belongs to the hierarchy of operational amplifier, voltage-feedback amplifier, analog signal-conditioning IC, and power-management semiconductor. Its quad configuration integrates four amplifiers, reducing package count when a system needs multiple independent gain stages. Key features include unity-gain stability, rail-to-rail output swing, low typical operating current of 19 µA, and a gain-bandwidth product of 190 kHz. The maximum input-offset voltage is 150 µV, while the stated input-offset current is 0.3 nA typical. According to the available manufacturer information, advanced CMOS technology provides low bias current, high open-loop gain, high-speed operation, and rail-to-rail output swing. The 0.08 V/µs slew rate provides adequate signal-bandwidth performance for low-frequency instrumentation, sensor interfaces, and general-purpose analog conditioning. Noise is specified as 2.2 µV peak-to-peak to 10 Hz, and common-mode rejection reaches 100 dB in the supplied specification data. These characteristics suit precision-oriented designs where input offset, current draw, and usable output range are more important than high-speed operation. Typical uses include battery-powered sensor acquisition, portable measurement equipment, low-voltage analog filtering, current sensing, and general-purpose buffering. Each of the four amplifier sections can perform voltage amplification, buffering, filtering, or comparison functions when supported by suitable feedback networks. The single-supply range also permits direct operation from 2.3 V, 3.3 V, or 5 V rails where appropriate system headroom is available. Designers should verify input common-mode range, output swing under load, noise at the signal bandwidth of interest, and stability with the selected feedback network. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs must not be left floating. Because the MCP619-I/P uses a through-hole PDIP-14 footprint, its replacement must match the same 14-pin package and pin arrangement. This product page consolidates verified pricing, supply information, package details, operating characteristics, selection guidance, and engineering considerations. It also distinguishes verified same-family options from true drop-in alternatives, helping engineers avoid confusing a functional substitute with a PCB-compatible replacement.

見積もり お問い合わせ
MCP619-I/ST - 190 kHz Micropower Quad Op Amp | Microchip
MCP619-I/ST

MCP619-I/ST - 190 kHz Micropower Quad Op Amp | Microchip

The Microchip Technology MCP619-I/ST is a quad micropower operational amplifier with a 190 kHz gain-bandwidth product, typical operating current of 19 µA per amplifier, and input offset voltage below 150 µV. It operates from 2.3 V to 5.5 V and is packaged in a 14-pin TSSOP for industrial temperature operation from -40°C to +85°C. A micropower operational amplifier is a low-current linear amplifier designed to provide voltage gain, filtering, buffering, or analog signal conditioning while consuming very little power. The MCP619 belongs to the broader operational amplifier, analog IC, and semiconductor hierarchy, making it suitable for battery-operated instruments, portable measurement systems, and low-power sensor interfaces. The quad configuration integrates four amplifiers, reducing component count and board area in designs that need several gain stages. Its 190 kHz gain-bandwidth product is adequate for low-frequency instrumentation, current-loop amplifiers, and slow sensor-conditioning paths. The 80 mV/µs slew rate supports small-signal step responses without requiring a high-speed general-purpose amplifier. Low power is the main technical advantage: a typical operating current of 19 µA per amplifier suits energy-limited designs better than standard 1 mA-class quad op amps. The device also combines a maximum input offset voltage of ±150 µV, typical input bias current of 0.3 nA, 100 dB CMRR, low input noise of 2.2 µVP-P to 10 Hz, and rail-to-rail output swing. Built-in compensation and reverse-phase input protection simplify common analog front-end layouts. Typical uses include portable ECG and biosignal conditioning, current sensing, bridge-sensor amplification, battery monitoring, general-purpose buffer and gain stages, and low-power data acquisition. Four amplifiers in one package are particularly useful when the system needs matched channels, sensor interfaces, or a mix of amplifiers and buffers. When designing with the MCP619-I/ST, keep the input and output stages close to the amplifier pins, provide stable feedback networks, and account for input bias-current error when driving high-impedance sources. The TSSOP package also requires careful solder-paste and reflow control to avoid bridging between the closely spaced leads. This page consolidates manufacturer specifications, package and pin information, sourcing guidance, design notes, and application-oriented selection advice into one engineering reference for the MCP619-I/ST.

見積もり お問い合わせ
MCP622-E/SN - 20 MHz Dual RAIL-to-Rail Op Amp | Microchip
MCP622-E/SN

MCP622-E/SN - 20 MHz Dual RAIL-to-Rail Op Amp | Microchip

The Microchip Technology MCP622-E/SN is a dual general-purpose operational amplifier with a 20 MHz typical gain-bandwidth product, 10 V/µs typical slew rate, and rail-to-rail input and output operation. The device is supplied in an 8-SOIC package and is identified by the verified product listings as the standard, general-purpose MCP622 configuration. An operational amplifier is an analog signal-conditioning IC used to amplify voltage differences, buffer analog signals, implement active filters, and drive downstream circuits. The MCP622 belongs to the operational-amplifier family within the broader semiconductor and analog-IC hierarchy. Its dual-circuit configuration allows two amplifier channels in one package, reducing component count and simplifying board layout in applications such as sensor interfaces, audio signal paths, control loops, and general-purpose analog conditioning. The MCP622-E/SN provides a 20 MHz typical gain-bandwidth product and 10 V/µs typical slew rate, making it suitable for moderate-bandwidth signal amplification. Its rail-to-rail output supports operation near the supply limits, while the input stage includes the negative rail. The verified specifications also identify 13 nV/√Hz typical input-noise density at 1 MHz, 70 mA typical short-circuit current, and calibrated input offset of ±200 µV maximum. The MCP62x family uses Microchip's mCal calibration technology. According to the manufacturer product-page description, the amplifier is self-calibrated at power-up, helping reduce input offset voltage. Some package variants include a calibration or chip-select pin for low-power operation and additional calibration control. The MCP622-E/SN is identified as a standard general-purpose dual amplifier rather than an automotive-qualified variant. Typical uses include low-voltage sensor conditioning, active analog filtering, instrumentation signal buffers, audio preamplification, and small-signal control applications. Because it is a dual amplifier, the two channels can be used independently or together for instrumentation, active filters, or multi-stage signal paths. Designers should use the manufacturer pin-description table when assigning PCB tracks and should confirm the power-supply limits and stability requirements from the official datasheet. This product page combines the verified manufacturer and distributor descriptions with engineering-focused application guidance, package details, comparison fields, and design considerations. It is intended to help engineers identify the correct amplifier and plan a robust implementation without obscuring which parameters require confirmation from the full manufacturer documentation.

見積もり お問い合わせ
MCP6234-E/P - 300 kHz Quad Rail-to-Rail Op Amp | Microchip
MCP6234-E/P

MCP6234-E/P - 300 kHz Quad Rail-to-Rail Op Amp | Microchip

The Microchip Technology MCP6234-E/P is a quad general-purpose operational amplifier with a 300 kHz gain-bandwidth product, 0.15 V/µs slew rate, and rail-to-rail input and output capability in a 14-pin PDIP package. It operates from a single supply as low as 1.8 V and is designed for low-voltage, low-power signal-conditioning systems. An operational amplifier, or op amp, is an analog building block that amplifies the voltage difference between its differential inputs. The MCP6234 combines four amplifiers in one package, placing it in the hierarchy of quad op amp, general-purpose amplifier, analog IC, and integrated circuit. Rail-to-rail inputs allow the input common-mode range to approach the supply rails, while rail-to-rail outputs support low-voltage sensor and signal-chain designs without requiring a separate output amplifier. Key electrical characteristics include a 300 kHz gain-bandwidth product, 0.15 V/µs slew rate, and approximately 20 µA typical supply current per amplifier. The family operates from 1.8 V and features a typical phase margin of 65 degrees. The MCP6234-E/P is specified in a 14-pin PDIP package with a 0.300-inch, 7.62 mm body width and is supplied in a tube. A typical input offset voltage of 5 mV is listed for this variant. The device is suited to portable measurement systems, low-voltage sensor interfaces, audio and communication signal conditioning, current monitoring, and general instrumentation. Its low supply voltage and low quiescent current are valuable in battery-powered equipment, while the 300 kHz bandwidth covers audio and low-frequency control applications rather than high-speed precision waveform work. When designing around the MCP6234-E/P, verify the common-mode and output swing limits against the actual signal and load. Decouple each supply connection close to the device, use short feedback paths, and check the unity-gain stability and output drive requirements before selecting external compensation or filtering networks.

見積もり お問い合わせ