インターフェースIC
サブカテゴリ
製品 (1151)
TMUX7208 - 44V Latch-Up Immune 8:1 MUX | Texas Instruments
The Texas Instruments TMUX7208 is a precision 8:1 single-channel multiplexer designed for high-voltage, high-performance signal routing. It operates from a single supply of 4.5V to 44V, dual supplies of ±4.5V to ±22V, or asymmetric supplies such as VDD=12V and VSS=-5V. The device features a low on-resistance of 4Ω (typical) and low charge injection of 3pC, making it suitable for precision analog applications. The TMUX7208 is available in a 16-pin TSSOP (PW) package and supports a wide operating temperature range of -40°C to +125°C. A multiplexer (MUX) is a device that selects one of several analog or digital input signals and forwards it to a single output line. The TMUX7208 is an analog multiplexer, specifically an 8:1 configuration, meaning it routes one of eight input channels to a common output based on the state of three address pins and an enable pin. This functionality is essential in data acquisition systems, test equipment, and industrial automation where multiple sensors or signals need to be sampled sequentially by a single ADC or measurement circuit. Key features of the TMUX7208 include latch-up immunity, which prevents damage from overvoltage or ESD events, and 1.8V logic-compatible inputs, allowing direct interface with low-voltage microcontrollers without level shifters. The device supports high current up to 300mA (max), making it robust for various loads. The low on-resistance and charge injection ensure minimal signal distortion and glitches during switching. The TMUX7208 uses a precision architecture with a break-before-make switching mechanism, preventing momentary shorting between channels. The device also features an enable pin that, when low, disconnects all channels, providing a high-impedance state. This is useful for power-down or isolation scenarios. The wide supply range and latch-up immunity make it ideal for industrial and automotive environments where voltage transients are common. Typical applications include data acquisition systems, test and measurement equipment, industrial process control, and battery monitoring systems. The TMUX7208 can be used to multiplex multiple sensor inputs into a single ADC, reducing component count and cost. Its high-voltage capability allows direct connection to 24V industrial buses without additional level shifting. When designing with the TMUX7208, ensure that the supply voltages are within the specified range and that the input signals do not exceed the supply rails. Proper decoupling capacitors on the supply pins are recommended to minimize noise. The address and enable pins should be driven with logic levels compatible with 1.8V to 5V, as the device is 1.8V logic compatible.
TMUX8108 - 100V Flat RON 8:1 MUX | Texas Instruments
The TMUX8108 is a modern high-voltage analog multiplexer from Texas Instruments, offering a single-ended 8:1 configuration with flat on-resistance (RON) and latch-up immunity. It operates with dual supplies, a single supply, or asymmetric supplies up to a maximum supply voltage of 100 V. The device supports bidirectional analog and digital signals on the source (Sx) and drain (Dx) pins, and all logic inputs support 1.8 V, 3.3 V, and 5 V logic levels, with the ability to connect as high as 48 V for system flexibility. An analog multiplexer is a device that routes one of several input signals to a common output based on digital control signals. In a single-ended 8:1 configuration, the TMUX8108 selects one of eight input channels and connects it to a single output. This functionality is essential in data acquisition systems, test equipment, and industrial automation where multiple sensors or signals need to be sampled sequentially by a single ADC or measurement circuit. The multiplexer acts as a signal router, enabling efficient use of expensive analog-to-digital converters and reducing component count. Key features of the TMUX8108 include a flat RON of 50 ohm, which minimizes distortion and ensures consistent performance across the input voltage range. The device provides latch-up immunity, preventing damage from overvoltage or overcurrent conditions. It supports a wide supply range up to 100 V, making it suitable for high-voltage industrial and automotive applications. The logic inputs are compatible with 1.8 V, 3.3 V, and 5 V systems, allowing direct interface with modern microcontrollers without level shifters. Technically, the TMUX8108 is built on a high-voltage CMOS process that enables low leakage currents and fast switching times. The flat RON characteristic is achieved through careful design of the switch architecture, ensuring that the on-resistance remains nearly constant across the entire analog input range. This reduces signal distortion and improves accuracy in precision measurement systems. The device also features break-before-make switching to prevent momentary shorting of channels during transitions. Typical applications include data acquisition systems, automated test equipment, industrial process control, and battery monitoring systems. In data acquisition, the TMUX8108 allows a single ADC to sample multiple sensor channels, reducing cost and board space. In battery monitoring, it can route individual cell voltages to a measurement circuit, enabling accurate state-of-charge estimation. The high-voltage capability makes it ideal for automotive 48 V systems and industrial 24 V or 48 V buses. When designing with the TMUX8108, ensure that the supply voltages are within the absolute maximum ratings and that the logic control signals are properly referenced to the logic supply. The device requires careful PCB layout to minimize parasitic capacitance and maintain signal integrity, especially in high-frequency applications. Additionally, consider the on-resistance and leakage current when calculating system accuracy, as these parameters affect the overall measurement error.
TMUXHS4412IRUAR - 20Gbps 4-Ch 2:1/1:2 Mux/Demux | Texas Instruments
The Texas Instruments TMUXHS4412IRUAR is a 4-channel, 20 Gbps bidirectional differential 2:1/1:2 multiplexer/demultiplexer in a 42-pin WQFN (RUA, 3.5 mm x 9 mm) package with exposed thermal pad, providing an 8 ohm on-state resistance and a typical -3 dB bandwidth of 13 GHz across each high-speed lane. The device supports USB 3.2 Gen 2x2, USB 3.2 Gen 1, USB 2.0, DisplayPort 1.4, SATA, PCIe Gen 3, SAS, and MIPI DSI/CSI by routing two differential sources to a single differential sink or vice versa with sub-130 ns propagation delay and 50 ps intra-pair skew. A high-speed multiplexer/demultiplexer (mux/demux) is a passive analog switch that selects one of multiple differential input pairs to a single output pair, enabling a host controller to share one PHY across two connectors, two PHYs across one connector, or to switch between redundant high-speed data paths. In the signal chain hierarchy the mux/demux sits between the protocol physical layer (PHY) and the connector, providing galvanic isolation between channels while preserving signal integrity at multi-gigabit NRZ and PAM3/PAM4 signaling rates. The TMUXHS4412 implements bidirectional switching so the same device serves either mux (2:1) or demux (1:2) topology without firmware configuration. Key differentiating features include 20 Gbps per-channel data rate (enabling USB 3.2 Gen 2x2 with two channels aggregated), 50 ps intra-pair skew, 8 ohm RON, 0.45 pF typical on-capacitance, sub-130 ns propagation delay, and dual supply support with 1.71 V to 1.98 V core and 3.0 V to 3.6 V I/O. The 42-pin WQFN (RUA) package provides a 31 C/W thermal pad-to-ambient resistance and supports -40 C to +105 C industrial operation. The architecture uses a pair of differential CMOS pass gates per channel with an integrated charge pump to maintain low RON across the full signal swing, plus on-chip termination resistors selectable through SEL pins. The bidirectional design means the same part handles both upstream and downstream switching, simplifying inventory and reducing PCB layout differences between mux and demux placements. Typical applications include USB Type-C port multiplexers, DisplayPort dual-mode source switching, PCIe lane failover, SATA port multipliers, and front-panel USB-C routing on motherboards, docking stations, and embedded computing platforms. The wide 3.0 V to 3.6 V supply range makes it compatible with both 3.3 V I/O rail and modern sub-1.8 V core supplies. When designing with the TMUXHS4412, route the high-speed differential pairs as 90 ohm differential impedance with length matching to within 5 mils, place decoupling capacitors within 2 mm of each supply pin, and solder the exposed thermal pad to a thermal land on a high-K board to maintain the full -40 C to +105 C temperature range without additional vias. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that are not consolidated in the manufacturer datasheet, including 8 ohm RON and 13 GHz bandwidth values verified from the TI TMUXHS4412 datasheet.
TMUXHS4446RETT - USB-C 10Gbps Alt Mode Crossbar Mux | Texas Instruments
The Texas Instruments TMUXHS4446RETT is a high-speed bidirectional passive crosspoint switch (crossbar, Xbar) that switches USB 3.2 Gen2 SuperSpeed and DisplayPort 1.4/2.1 (up to 10 Gbps UHBR10) signals over a USB Type-C interface, with 7-ohm typical on-resistance, a 6x4 mux configuration, and a 40-pin WQFN (6 mm x 3 mm) package with exposed pad. A crosspoint switch or crossbar mux is a switching matrix in which any input lane can be routed to any output lane, giving system designers complete flexibility in high-speed signal routing. In the USB Type-C ecosystem, crossbar switches sit between the SuperSpeed/sideband pins of the USB-C connector and a device's USB 3.2 or DisplayPort controller, resolving the orientation and alternate-mode ambiguity that the reversible Type-C connector introduces. As such, it belongs to the analog switch and multiplexer family within signal-switching ICs, sitting between the USB-C connector and the SoC in the system hierarchy. Key features include support for USB 3.2 Gen2 (10 Gbps) SuperSpeed lanes and DisplayPort 1.4/2.1 UHBR10 signaling, integrated low-speed SBU switching for DisplayPort auxiliary (AUX) channels, and a passive, bidirectional switch architecture that adds minimal signal degradation. The 7-ohm typical on-resistance minimizes insertion loss impact on high-speed differential pairs, helping preserve eye diagrams at 10 Gbps rates. Architecturally, the TMUXHS4446 is a passive FET-switch crossbar rather than an active redriver or retimer. This means it consumes minimal power, introduces no added latency, and does not regenerate the signal, so total channel budget must account for its on-resistance and capacitive loading. Passive switching makes it ideal when the host and device have adequate link budget and no equalization is required. Typical applications include USB Type-C docks and dongles that switch between USB 3.2 and DisplayPort alternate mode, notebooks and tablets routing DP 1.4/2.1 lanes to a USB-C port, monitors with USB-C inputs, and smartphone or mobile-compute platforms requiring USB-C orientation and alternate-mode switching. A key design consideration is that because the part is passive, total insertion loss across the connector, PCB traces, and switch must fit the USB 3.2 Gen2 or DP UHBR10 channel budget; keep routing short and impedance-controlled. Follow TI's datasheet layout guidance for the exposed-pad WQFN. This page synthesizes distributor pricing data, drop-in alternative analysis, and practical design notes that go beyond the manufacturer datasheet, giving engineers a single citable reference for the TMUXHS4446RETT.
TRS3221EIDBR - 3-5.5V RS-232 Transceiver, ±15kV ESD | Texas Instruments
The Texas Instruments TRS3221EIDBR is a 3-V to 5.5-V single-channel RS-232 line driver/receiver with ±15-kV IEC-ESD protection, packaged in a 16-pin SSOP (DB). It operates from a single supply rail and integrates a charge-pump that generates the ±RS-232 voltage swing from the input supply, so no external ±12 V rails are required. The device supports data rates up to 250 kbps and is rated for ±15-kV HBM, ±8-kV IEC 61000-4-2 contact, and ±15-kV IEC 61000-4-2 air-gap ESD strikes on the RS-232 bus pins. An RS-232 transceiver is a type of line driver/receiver IC that converts logic-level (typically 0/3.3 V or 0/5 V CMOS/CMOS) UART signals into the ±5 V to ±15 V voltage swings required by the TIA/EIA-232-F and ITU v.28 standards. It belongs to the broader interface-IC category, sitting between the UART block of a microcontroller/SoC and a DB-9 (or equivalent) connector on the serial port. Single-channel variants like the TRS3221E serve compact, point-to-point designs where two driver/receiver channels are not needed, helping shrink BOM cost and PCB area versus 2-channel parts. Key features include 1 driver and 1 receiver per channel, a dedicated enable input for power management, an auto-powerdown mode that drops quiescent current to 1 µA typical when the cable is disconnected, and an always-active supplementary receiver that monitors the ring-indicator path even in shutdown. The device meets or exceeds the TIA/EIA-232-F and ITU v.28 electrical specifications, and is offered in industrial temperature grades of -40 °C to +85 °C. A high-speed pin-compatible upgrade, the TRSF3221E, is available where 1 Mbit/s operation is required. The TRS3221E uses an on-chip switched-capacitor voltage converter with four external 0.1 µF charge-pump capacitors. The architecture tolerates supply rails as low as 3.0 V while still generating compliant ±5 V (minimum) RS-232 output swings, which is the headline advantage over legacy 5-V-only RS-232 transceivers. Drivers are slew-rate limited to keep EMI low, and the receivers include hysteresis to reject noise on long cables. Typical applications include industrial single-port serial ports, point-of-sale terminals, handheld data collectors, factory automation equipment, medical instruments with DB-9 serial interfaces, and any embedded system that needs a robust RS-232 link from a 3.3 V or 5 V UART. Designers often pair this part with a TVS array for additional surge protection when the cable is exposed to outdoor or industrial transients. When designing with the TRS3221EIDBR, place the four charge-pump capacitors (typically 0.1 µF X7R) as close as possible to the C0+, C0-, C1+, C1- pins to minimize supply ripple. Decouple VCC with a 0.1 µF + 1 µF combination near the pin, and respect the absolute-maximum ratings on the RS-232 outputs (typically ±13.2 V) by avoiding back-drive when the IC is unpowered. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
TRS3221EIRGTR - 3-5.5V RS-232 Transceiver, 250kbps, ±15kV ESD | Texas Instruments
The Texas Instruments TRS3221EIRGTR is a 3- to 5.5-V single-channel RS-232 line driver/receiver delivering 250 kbps data rate with ±15 kV IEC-ESD protection in a 16-pin VQFN (RGT) package measuring 3x3 mm with an exposed thermal pad. The device integrates one driver and one receiver, supports VCC operation from 3.0 V to 5.5 V (compatible with TTL/CMOS logic levels), and meets or exceeds the requirements of TIA/EIA-232-F and ITU v.28 standards. An RS-232 transceiver is a charge-pump-based interface IC that translates between TTL/CMOS logic levels (0-3.3 V or 0-5 V) and the ±5 V to ±15 V swing required by the legacy TIA/EIA-232-F serial communication standard. RS-232 transceivers belong to the broader interface IC family, which sits hierarchically between discrete level-shifters and protocol controllers (UARTs) in wired communication systems. RS-232 remains widely deployed in industrial equipment, point-of-sale terminals, medical instruments, and embedded debug ports where simplicity, point-to-point connectivity, and proven robustness outweigh the bandwidth advantages of USB or Ethernet. Key features include ±15 kV Human-Body Model (HBM) ESD protection on RS-232 pins, ±8 kV IEC 61000-4-2 contact discharge, ±15 kV IEC 61000-4-2 air-gap discharge, and an automatic powerdown feature that disables drivers when no valid RS-232 cable is detected. The on-chip dual charge pump requires only four external 0.1 µF capacitors, enabling true 5 V operation from a single 3.3 V supply without a separate ±12 V rail. The 250 kbps data rate is adequate for all standard RS-232 baud rates up to and beyond 115200 with margin to spare. The architecture combines a regulated switched-capacitor voltage doubler/inverter with a proprietary low-dropout RS-232 driver stage and a precision hysteresis receiver. ESD protection is implemented at the cable-side pins using TI's integrated silicon-controlled-rectifier (SCR) clamps. The 16-pin VQFN package's exposed pad provides a low thermal resistance path, which is useful when the part operates near the upper end of its 1 mA quiescent current budget in warm enclosures. Typical applications include industrial PLC programming ports, point-of-sale (POS) terminals, medical device serial consoles, battery-powered handhelds, and embedded debug UARTs that need robust ESD performance in the field. The TRS3221EIRGTR's small 3x3 mm footprint suits space-constrained designs such as USB-to-serial dongles, IoT gateways, and barcode scanners. When designing with this part, place the four charge-pump capacitors as close as possible to the C1+ / C1- / C2+ / C2- pins and keep the RS-232 trace lengths short to maximize ESD margin. Note that the TRSF3221E is the higher-speed (1 Mbit/s) pin-compatible alternative if 250 kbps is insufficient. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
TRSF3222CPW - 3V-5.5V RS-232 Transceiver, 2/2 Drivers | TI TSSOP-20
The Texas Instruments TRSF3222CPW is a 2-driver/2-receiver RS-232 line transceiver that operates from a single 3.0V to 5.5V supply in a 20-pin TSSOP package. It supports data rates up to 1 Mbit/s and accepts 5-V logic inputs when powered from a 3.3V rail, making it ideal for mixed-voltage system designs. A line transceiver is an interface device that bridges a logic-level UART (universal asynchronous receiver/transmitter) on a host microcontroller with the RS-232 standard, which swings between +12V and -12V on the bus side. It sits within the Interface IC hierarchy (RS-232 transceiver -> line transceiver -> interface IC -> integrated circuit) and converts TTL/CMOS logic levels to TIA/EIA-232-F compliant voltage levels while protecting the host from ESD events on the cable side. The TRSF3222CPW integrates a dual charge-pump that generates the required +5.5V and -5.5V rails from a single 3.3V supply using four small 0.1 uF external capacitors. Standby current is typically 1 uA, supporting low-power portable designs. The receivers remain active in shutdown, allowing wake-up characters to be detected without waking the host. ESD protection exceeds +/-15 kV HBM on the bus pins. Typical applications include industrial point-of-sale terminals, factory automation equipment, portable diagnostic instruments, and battery-powered barcode scanners where 3.3V logic must communicate with legacy RS-232 peripherals. The wide 3.0V-5.5V supply range also makes the part suitable for USB-to-serial bridges and embedded computing modules. When designing with this device, place the four charge-pump capacitors as close to the IC as possible to minimize loop inductance. The TSSOP-20 footprint requires standard surface-mount assembly with a maximum reflow temperature per JEDEC J-STD-020. Decouple VCC with a 0.1 uF ceramic plus a bulk tantalum if the supply impedance is high.
TS3A27518ERTWR - 6-Ch 2:1 Analog Mux, 240MHz | Texas Instruments
The Texas Instruments TS3A27518ERTWR is a bidirectional 6-channel 1:2 (SPDT) analog multiplexer/demultiplexer with 6.2 ohm on-resistance, 240 MHz bandwidth, and integrated IEC 61000-4-2 ESD protection, housed in a 24-pin WQFN (4x4 mm) package operating from a 1.65 V to 3.6 V single supply. An analog multiplexer is a signal-routing semiconductor that selects one of several input channels and connects it to a common output, functioning as a digitally controlled switch for both analog and digital signals. Within the signal-chain hierarchy, it sits between passive switches and full crosspoint matrices, and belongs to the broader family of interface and analog switch ICs used in power management and signal conditioning subsystems. Key features include low 6.2 ohm typical on-resistance for minimal signal attenuation, 21.5 pF typical switch capacitance, up to 240 MHz bandwidth for high-speed rail-to-rail signal handling, and -62 dB crosstalk and OFF isolation. The device also provides isolation in power-down mode (VCC = 0 V), and 1.8 V logic-threshold-compatible control inputs that allow direct interfacing with low-voltage microcontrollers. Architecturally, the TS3A27518E uses two control pins, each simultaneously controlling three 1:2 multiplexer sections, plus an enable pin that places all outputs in high-impedance mode. Integrated ESD cells rated to IEC 61000-4-2 on the signal pins eliminate the need for external TVS diodes in USB and port-protection designs, and the device is qualified for automotive applications. Typical applications include USB 2.0 high-speed signal switching, audio jack and headset detection, battery-powered portable equipment, and general-purpose analog signal routing in industrial systems. A key design consideration is on-resistance flatness across the signal range: at lower VCC the Ron rises, so budget for insertion loss at 1.65 V operation, and keep stub lengths short to preserve the 240 MHz bandwidth. This page adds value beyond the datasheet by synthesizing distributor pricing tiers, drop-in alternatives, cross-reference data, and practical design notes in one reference.
TS3A44159RGTR - 0.45Ω Quad SPDT Analog Switch | TI
The Texas Instruments TS3A44159RGTR is a 0.45-Ω quad-channel single-pole double-throw (SPDT) analog switch housed in a 16-pin VQFN (RGT) 3x3 mm package. Operating from 1.65 V to 4.3 V, it delivers low on-state resistance with excellent Ron matching across four independent 2:1 multiplexers and supports bidirectional signal flow on every channel. Two logic-level control inputs select between the NO/NC paths of all four switches simultaneously, simplifying firmware-driven signal routing. An analog switch is a solid-state semiconductor device that routes analog or digital signals between two or more terminals under the control of a logic-level signal. It belongs to the analog switch and multiplexer family, which sits inside the broader interface IC category of integrated circuits. Quad SPDT switches are commonly used to swap between two sources on four channels at once, an arrangement also called a 2-channel DPDT function in this device. Key features include 0.45 Ω typical on-state resistance, 50 pA typical switch leakage, break-before-make switching to prevent momentary channel cross-connection, and a -3 dB bandwidth greater than 35 MHz. The control inputs are 1.8 V logic-compatible, while supply operation extends from 1.65 V to 4.3 V. ESD protection on the switch pins exceeds 2000 V per the HBM model. Architecturally the part uses CMOS transmission gates with integrated charge-pump-derived well biasing, enabling low Ron and rail-to-rail signal swing on a single positive supply. Ron flatness is held tight across the input common-mode range, which preserves harmonic distortion performance in audio paths. The device draws only microamps of quiescent current, which is essential for battery-powered systems. Typical applications include portable audio routing between headphone jack and Bluetooth receiver, USB 2.0 high-speed signal switching, SPI/I²C bus multiplexing, smartphone audio codec path selection, and PDA or portable media player source switching. Industrial uses include 4-wire resistance measurement multiplexing and analog front-end signal routing. When designing with this part, ensure that the logic-high level on IN1/IN2 exceeds 0.85 x VDD and the logic-low is below 0.15 x VDD to guarantee full CMOS-level switching. Place 0.1 µF bypass capacitors within 5 mm of the VDD pin to keep digital control noise out of the analog path. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical PCB layout guidance not found in the manufacturer datasheet alone.
TS3A4741DCNR - 0.9Ω Dual SPST Analog Switch | TI SOT-23-8
The Texas Instruments TS3A4741DCNR is a 0.9 Ω low on-resistance, low-voltage, single-supply, dual single-pole single-throw (SPST) analog switch housed in an 8-pin SOT-23 (DCN) package. It integrates two independent normally open (NO) switches, each with a 1:1 (SPST) topology, designed for 1.8 V logic compatibility when operated from a single 3 V supply rail. What is an SPST analog switch? An SPST (Single-Pole Single-Throw) analog switch is a solid-state semiconductor device that routes analog signals by electrically connecting or isolating one signal path. The TS3A4741 belongs to the broader category of analog switches and multiplexers, a subfamily of interface ICs used for signal routing in mixed-signal and low-power systems. Compared with mechanical relays, analog switches offer far faster switching speeds, lower power, smaller PCB area, and no mechanical bounce, at the cost of lower absolute voltage and current handling. Key specifications include a 0.9 Ω typical on-resistance (Ron), 1.8 V CMOS-compatible digital logic inputs, rail-to-rail analog signal handling, very low quiescent current, and integrated ESD protection. The two switches operate completely independently, allowing them to be used as separate signal paths or as complementary paths in a single function. The device is fabricated in a CMOS process and supports fast switching speeds, low off-leakage current, and bidirectional analog signal flow. Its small SOT-23-8 footprint and 1.8 V logic compatibility make it well suited to portable and battery-powered designs. Typical applications include audio signal routing in portable devices, switching between two sensors in handheld instruments, power rail multiplexing in low-power systems, and general-purpose signal gating in test equipment and consumer electronics. When designing with the TS3A4741, ensure the analog signal stays within the supply rails to avoid distortion or excessive leakage, and add 0.1 µF decoupling close to VCC. For applications requiring normally closed (NC) switches, use the pin-compatible TS3A4742. This page synthesizes verified distributor pricing, same-brand and cross-brand drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
TS3A4751PWR - 0.9-Ohm Quad SPST Analog Switch | Texas Instruments
The Texas Instruments TS3A4751PWR is a bidirectional, 4-channel, normally-open (NO) single-pole single-throw (SPST) analog switch in a 14-pin TSSOP package. It operates from a single 1.6V to 3.6V supply, delivers a maximum on-state resistance of 0.9 ohm at a 3V supply, and handles rail-to-rail analog signals with fast switching speeds and very low quiescent power. An analog switch is an IC that routes or isolates analog signal paths under digital control. Within the signal-routing hierarchy, the TS3A4751 belongs to the SPST switch family, a subset of analog switches and multiplexers used in signal conditioning and power-management systems. Key features include 0.9-ohm maximum Ron at 3V (1.5-ohm maximum at 1.8V), Ron flatness of 0.4-ohm maximum at 3V, and Ron matching of 0.05-ohm maximum at 3V. The 1.8-V CMOS-compatible digital inputs allow direct interface with low-voltage GPIO when using a 3-V supply, eliminating level-shift circuitry. The device is available in 14-pin TSSOP (PW), 14-pin VQFN (RGY), and 2x2-mm micro X2QFN (RUC) packages. The low Ron supports power-switching and low-distortion signal paths, while rail-to-rail operation preserves full signal swing on 1.8V, 2.5V, and 3.3V rails. Typical applications include low-voltage power switching, audio signal routing in portable devices, battery-powered test points, and general-purpose signal muxing in smartphones, tablets, and industrial sensing modules. Its normally-open configuration makes it suitable for fail-safe, default-disconnected paths. When designing, remember that Ron rises at lower supply voltages: at a 1.8-V supply the maximum Ron is 1.5 ohm, so account for insertion loss and on-resistance flatness in high-fidelity or precision-current paths. According to TI datasheet, the TS3A4751 is the NO-switch counterpart within the TI low-voltage quad SPST family.
TS3A5018PWR - 10-Ohm Quad SPDT Analog Switch | Texas Instruments
The Texas Instruments TS3A5018PWR is a quad single-pole double-throw (SPDT) analog switch designed to operate from a 1.8V to 3.6V supply in a 16-pin TSSOP (PW) package rated from -40C to +85C. It handles both digital and analog signals, and signals up to V+ can be transmitted in either direction. An analog switch is a semiconductor device that selectively connects or disconnects an analog signal path under digital control. It is a fundamental signal-routing building block in the broader family of multiplexers, demultiplexers, and interface ICs. Analog switches provide a low-resistance path when ON and a high-impedance path when OFF, replacing bulky mechanical relays in audio/video routing, data acquisition, and communication systems. Key features include the wide 1.8V to 3.6V operating range (ideal for battery-powered and 3.3V systems), low 10-ohm ON-state resistance with excellent channel-to-channel matching, and low charge injection that minimizes glitches during switch transitions. All four SPDT switches share a common enable function so the entire device can be disabled to reduce power consumption. The TS3A5018 is built on TI CMOS process technology, providing low quiescent power dissipation and high reliability. Bidirectional signal flow means either of the two throw terminals can serve as the port, essential for multiplexing and demultiplexing on the same hardware. Turn-on and turn-off times are fast, supporting high-speed signal routing in data converters and communication interfaces. Typical applications include audio signal routing in portable devices, battery-powered data acquisition front ends, communication interface switching, and test equipment signal multiplexing. The low power consumption and wide supply range make it well suited for portable and industrial designs. Design consideration: the 10-ohm ON resistance introduces series attenuation in high-impedance circuits, so prefer low-impedance loads or buffer the switched node. Place a 0.1uF decoupling capacitor close to the V+ pin, and use the enable pin in battery designs to cut standby current when switching is idle.
TS3USB3000MRSER - DPDT USB 2.0/MHL Switch | TI | UQFN-10
The Texas Instruments TS3USB3000MRSER is a double-pole, double-throw (DPDT) analog switch that combines a USB 2.0 High-Speed (480 Mbps) switch and a Mobile High-Definition Link (MHL) switch in a single 10-pin UQFN (RSE) package measuring 1.5 mm × 2.0 mm. It supports a -3 dB bandwidth of 6.1 GHz on the MHL path and operates from a 2.3 V to 4.8 V supply. The device is designed to share a common USB or Micro-USB connector between USB 2.0 data and MHL video signals in mobile phones, tablets, and portable media devices. A USB switch IC is a special-purpose analog multiplexer that routes high-speed differential signals between a single downstream port and two upstream paths (host vs. MHL sink). In the hierarchy of power management and signal routing components, this part belongs to the USB interface IC category, sitting between the connector and the application processor. DPDT switches such as the TS3USB3000 are critical because they must pass 480 Mbps USB signals and up to 3 GHz MHL content with minimal insertion loss, low crosstalk, and high off-isolation. Key features of the TS3USB3000 include low on-resistance (Ron) on the USB data paths, low on-capacitance (Con) for high-bandwidth signal transmission, 1.8-V-compatible select pins for direct GPIO control from a mobile processor, and a quiescent current of approximately 5 uA. The wide supply range (2.3 V to 4.8 V) covers both 3.3 V system rails and the typical 3.8 V Li-ion battery range without additional regulation. The small 1.5 mm × 2 mm UQFN footprint makes it ideal for space-constrained mobile applications. The TS3USB3000 uses a charge-pump-less architecture with simple CMOS logic-level select inputs. The two select pins (S1 and S0 per TI documentation) determine whether the common port is routed to the USB path or the MHL path. Internal ESD protection on the signal pins improves robustness against connector-level transients, which is critical for hot-plug consumer electronics. Typical applications include smartphones and tablets with MHL-enabled video output, automotive infotainment systems that mirror mobile content via USB or MHL, portable media players, and USB/MHL dongles. The wide bandwidth also makes it suitable for any system needing to multiplex two high-speed differential pairs onto a single connector. When designing with this part, place the device as close as possible to the USB/MHL connector to minimize stub lengths and signal-integrity degradation. Use controlled-impedance differential routing (90 ohm) on both sides of the switch, and provide adequate ground stitching vias along the signal path to maintain return-current continuity. This page synthesizes distributor pricing, pin-compatible alternatives, and practical design notes that are not aggregated in any single manufacturer datasheet or distributor catalog page.
TS5A2053 - 10Ω SPDT Analog Switch | Texas Instruments
The TS5A2053 is a single-pole double-throw (SPDT) analog switch from Texas Instruments, designed to operate from 1.65 V to 5.5 V. It can handle both digital and analog signals, and signals up to V+ can be transmitted in either direction. The device features a low ON-state resistance of 10Ω (typical) and includes an enable pin for power management. It is available in the 8-pin VSSOP (DCU) package, making it suitable for space-constrained applications. An analog switch is a semiconductor device that selectively connects or disconnects an analog signal path based on a digital control signal. It is a fundamental building block in signal routing, multiplexing, and sample-and-hold circuits. Analog switches are part of the broader category of interface ICs, which manage signal integrity and connectivity between different subsystems in electronic systems. Key features of the TS5A2053 include a low ON-state resistance of 10Ω, which minimizes signal attenuation, and a wide operating voltage range from 1.65 V to 5.5 V, allowing compatibility with various logic levels. The device also offers fast switching speeds, with a typical turn-on time of 20 ns and turn-off time of 15 ns, making it suitable for high-frequency signal routing. The enable pin allows the switch to be disabled, reducing power consumption in standby modes. Technically, the TS5A2053 uses a CMOS process that provides low power consumption and high ESD robustness. The device has a bandwidth of 300 MHz, enabling it to pass high-frequency signals with minimal distortion. The ON-state resistance is flat across the input voltage range, ensuring consistent performance. The device also features break-before-make switching, preventing momentary short circuits between channels. Typical applications include audio signal routing, data acquisition systems, and test equipment. In audio systems, the low ON-state resistance and high bandwidth ensure minimal signal degradation. In data acquisition, the switch can route analog signals to an ADC, with the enable pin allowing power saving when not in use. In test equipment, the TS5A2053 can be used for signal multiplexing and routing. When designing with the TS5A2053, it is important to consider the ON-state resistance and its effect on signal integrity. For high-frequency signals, the parasitic capacitance of the switch can cause signal attenuation, so proper PCB layout and termination are recommended. Additionally, the enable pin should be tied to a defined logic level to avoid floating inputs.
TSB011 - Data Unverified, No Confirmed Electronic Component Found
The MPN TSB011 could not be confirmed as a specific electronic component from the verified web data retrieved for this query. Real-time distributor and manufacturer searches returned no unambiguous match for an electronic part with the exact designation TSB011. The search results instead surfaced several unrelated items that share similar designations: an ACCI TannerStone balustrade catalog item (TSB011), a Texas Instruments TSB11C01DL IEEE 1394 FireWire link-layer controller distributed via Rochester Electronics, an Adam Tech TSB-11 terminal block, and an ITT TSB-011 regulator pressure relief device technical service bulletin for automotive fuel systems. What this means: part-number prefixes such as TSB are not exclusive to a single manufacturer, and near-miss designations (TSB011 vs TSB11 vs TSB-011 vs TSB11C01DL) point to completely different products across mechanical, electrical, and automotive domains. Generating electrical specifications for this MPN from these results would risk fabricating data, so all specification values are marked for verification. What is likely related: if the intended part is the Texas Instruments TSB11C01DL, that device is an IEEE 1394 (FireWire) link-layer controller IC classified by DigiKey under Drivers, Receivers, Transceivers within Interface ICs, supplied through Rochester Electronics as an authorized aftermarket source. If the intended part is the Adam Tech TSB-11, that is a terminal block in the Connectors family. Recommended next step: confirm the exact manufacturer prefix and full MPN (including any package suffix) before ordering. This page will be updated once verified datasheet data is available.
TSI384-133ILV - PCIe to PCI-X Bridge 256-BGA | Renesas Electronics
The Renesas TSI384-133ILV is a single-lane PCI Express (PCIe) to PCI/PCI-X bridge IC housed in a 256-ball PBGA (17x17 mm) package. The device supports x1 PCIe link width (configurable to x4 in some variants per datasheet family), bridging PCIe upstream to legacy PCI/PCI-X peripherals, and supports PCI-X frequencies up to 133 MHz and conventional PCI up to 66 MHz. A PCI-to-PCI bridge is a transparent or non-transparent protocol converter that maps transactions between two distinct PCI-family bus segments. PCI Express bridges sit in the broader hierarchy of: PCIe bridge -> PCIe-to-PCI bridge -> I/O bridge -> peripheral controller IC -> interface logic. Within Renesas' PCI/PCIe product family the Tsi384 is the higher-performance, higher-pin-count sibling of the smaller Tsi381 (144-ball BGA, 13x13 mm) for space-constrained designs. Key features of the TSI384-133ILV include transparent, non-transparent, and opaque (semi-transparent) bridging modes, supporting multi-host systems and storage adapter applications requiring domain isolation. The bridge enables superior throughput with up to four PCIe lanes per the family datasheet and supports asymmetric upstream/downstream widths. Industrial temperature grade and RoHS-compliant terminations suit embedded, telecommunications, and industrial computing designs. Architecture-wise the TSI384 combines a hardened PCIe PHY/transaction layer with a PCI/PCI-X controller core operating in conventional or PCI-X mode. The 256-ball PBGA provides the necessary power, ground, and high-speed signal routing headroom for x1 to x4 PCIe widths. Operating supply voltage is 1.2 V core plus I/O rails, supplied via multiple pins. Typical applications include PCI-to-PCI bridging in industrial single-board computers, storage adapter cards requiring domain isolation, legacy I/O expansion for new PCIe-only processors, telecommunications line cards needing PCI/PCI-X peripherals, and embedded PCIe-to-PCI backplane designs. When designing with this part note that it is reported by some distributors as obsolete or under last-time-buy; confirm lifecycle before starting a new design. Use the Renesas cross-reference document to evaluate the smaller-footprint Tsi381-66ILV for cost-sensitive designs. This page synthesises distributor pricing, parametric comparison with cross-brand PCIe bridges, and practical design notes that complement the Renesas Tsi384 user manual referenced in the data sources.
TUSB2046BVFR - 4-Port USB 2.0 Full-Speed Hub | TI
The Texas Instruments TUSB2046BVFR is a 4-port USB 2.0 full-speed (12 Mbps) hub controller with one upstream port and four downstream ports, implemented as a pure state-machine (no CPU core) in a 32-pin LQFP (VF, 7x7 mm) package. It operates from a single 3.0 V to 3.6 V supply, drawing approximately 40 mA, over a 0 C to 70 C commercial temperature range. A USB hub controller is a dedicated interface IC that expands a single USB upstream connection into multiple downstream ports, handling enumeration, transaction translation at the protocol level, and per-port power management. Within the system hierarchy it sits in the connectivity layer: interface IC > USB controller > hub controller, alongside host controllers and device controllers in a complete USB subsystem. Key features include full compliance with the USB specification as a full-speed hub (TI design TID #30220231), integrated USB transceivers that eliminate external PHY components, and an optional serial EEPROM interface for storing customized VID/PID and configuration data. Support for Win95/DOS-style operation and a pure hardware state-machine architecture reduce firmware complexity to zero - the hub enumerates automatically on plug-in. The TUSB2046B is fabricated on a low-power 3.3 V ASIC CMOS process. Because there is no embedded microcontroller, no firmware development, flash programming, or in-circuit emulator is required, which shortens qualification cycles and removes a whole class of field-update failure modes. The device supports individual downstream port power switching and overcurrent status inputs for compliant bus-powered and self-powered hub designs. Typical applications include standalone USB hubs, monitor and keyboard-display hubs, industrial and medical equipment USB expansion, and adding USB ports to embedded systems built around host processors without native hub capability. For design, provide 0.1 uF decoupling at each supply pin, strap configuration pins (or fit the optional EEPROM) for power-mode selection, and size port power switches per downstream port load. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
TUSB2046BVFRG4 - 4-Port USB 2.0 Full-Speed Hub | Texas Instruments
The Texas Instruments TUSB2046BVFRG4 is a 4-port USB 2.0 full-speed hub controller operating at 12 Mbps from a 3.3 V supply, housed in a 32-pin LQFP (7x7 mm) package with an optional serial EEPROM interface and a 0C to +70C commercial operating range. A USB hub controller is an interface IC that expands a single upstream USB port into multiple downstream ports, handling enumeration, transaction translation at the protocol level, and port power management. It sits within the USB device hierarchy between the host controller and downstream peripherals, forming a sub-family of the broader USB interface and connectivity IC class within semiconductor interface products. Key features include one upstream port and four downstream ports compliant with the USB 2.0 specification at full speed (12 Mbps), support for both low-speed (1.5 Mbps) and full-speed downstream devices, an optional serial EEPROM interface for storing vendor ID / product ID configuration data, and overcurrent detection inputs with power-switch control outputs for per-port or ganged power switching. Implementation with a digital state machine instead of an embedded microcontroller eliminates firmware development and reduces BOM complexity. Technical depth: because the TUSB2046B is a pure hardware state-machine design, enumeration latency is deterministic and there is no firmware to qualify, update, or corrupt. The 3.3 V CMOS core with integrated 3.3 V regulator support keeps external components minimal, typically requiring only a 6 MHz or 48 MHz clock source, bypass capacitors, and the external power switches for downstream VBUS. Typical applications include PC monitor hubs, docking stations, industrial panel USB expansion, printer and multifunction peripheral front panels, and embedded systems requiring additional USB ports from a single host connection. The 12 Mbps full-speed rating suits HID devices, flash drives, and instrumentation rather than high-bandwidth video or mass-storage arrays. Design consideration: budget downstream VBUS power carefully - each downstream port may supply up to 500 mA at 5 V per the USB specification, so external power MOSFET switches and overcurrent sensing resistors must be sized for the aggregate load, and the OVERCURRENT inputs must be wired to the correct power-switch pins. This page synthesizes distributor pricing context, drop-in alternatives, lifecycle status, and practical design notes not found in the manufacturer datasheet alone.
TUSB320HAIRWBR - USB Type-C CC Logic, X2QFN-12 | TI
The Texas Instruments TUSB320HAIRWBR is a USB Type-C Configuration Channel (CC) logic and port controller in an industrial-grade (I-temp) active-high enable variant, packaged in a 12-pin X2QFN (RWB) measuring 1.6 mm × 1.6 mm. The device operates from a single 3.3 V supply and supports USB Type-C Specification 1.1 while remaining interoperable with 1.0 systems. It advertises and detects up to 3 A of VBUS current per Type-C current-mode rules and supports DFP (Source), UFP (Sink), and DRP (Dual Role) port roles selected through MODE pins. A USB Type-C Configuration Channel Logic IC is a state-machine controller that sits between a USB Type-C receptacle and the application processor or USB controller. Its job is to negotiate attach/detach events, cable orientation (CC1/CC2 polarity), role (host vs device), and current advertisement (default 500 mA, 1.5 A, or 3 A) through the CC1/CC2 pull-up and pull-down signalling defined by the USB-IF Type-C specification. Higher up the hierarchy it is an Interface IC > USB Interface IC; below it is the CC PHY layer. Key features include: integrated 5.1 kΩ CC pull-up resistors that can be toggled for DRP toggle, hardware MODE pin configuration (no firmware needed), active-high enable (EN) pin for power sequencing, low standby current with a dedicated low-power mode, and HBM ESD protection on CC pins. The X2QFN-12 RWB package keeps the device under 3 mm² footprint, ideal for compact dongles, hubs, and embedded platforms. Typical applications are any 5 V / 3 A USB Type-C ports that need a low-BOM CC controller: travel chargers, USB Type-C dongles, adapters, hubs, docking stations, smartphones, tablets, and notebooks. Because it operates as a standalone state machine with no MCU required, it is well-suited to cost- and board-area-sensitive designs. Design consideration: place the 100 nF decoupling capacitor within 2 mm of VCC and keep the CC traces short, matched, and away from switching nodes to preserve signal integrity. A 0 Ω or ferrite series resistor on VBUS is optional but recommended to limit inrush current at attach. This page synthesizes distributor pricing, drop-in alternatives, application pairings, and design notes not found in the manufacturer datasheet, optimized for engineers sourcing USB Type-C port controllers.
TUSB320LAIRWBR - USB Type-C CC Logic & Port Controller | TI
The Texas Instruments TUSB320LAIRWBR is a USB Type-C configuration channel (CC) logic and port controller housed in a 12-pin X2QFN (RWB) package measuring 1.6 mm x 1.6 mm. It supports USB Type-C Specification 1.1, is backward compatible with 1.0, advertises and detects up to 3 A of VBUS current, and operates from a 2.7 V to 5 V supply. Configuration modes include Host Only (DFP/Source), Device Only (UFP/Sink), and Dual Role Port (DRP) for accessories, hubs, smartphones, and laptops. The "L" variant removes I2C and adds GPIO-controlled mode selection for ultra-low-power BOMs. What is a USB Type-C port controller? A USB Type-C port controller is an interface IC that sits between a USB 2.0 data path and the Type-C receptacle, managing the Configuration Channel (CC) pins that detect cable attach/detach, determine plug orientation (CC1 vs CC2), advertise the source/sink current capability through Rp/Rd pull-up/pull-down resistors, and negotiate power-role swap for USB Power Delivery. It belongs to the broader hierarchy of interface ICs -> USB interface ICs -> Type-C controllers -> USB Power Delivery controllers, occupying the link layer just above the physical connector. Key differentiating features include integrated CC logic, automatic DRP toggle, support for audio and debug accessory modes, an active-high ENABLE pin, and an open-drain INT output for interrupt-driven host polling. The device is offered in both I2C-configurable (TUSB320I) and pin-strapped/GPIO (TUSB320L) variants within the same X2QFN-12 footprint, allowing PCB reuse between firmware-driven and BOM-optimized designs. Operating temperature is -40 C to +85 C (industrial). The TUSB320L architecture is a pure hardware state machine that samples the CC1/CC2 pins, drives the appropriate Rp current source or Rd pull-down, and reports attach/orientation events to the application processor through dedicated GPIO flags. This eliminates the firmware overhead of I2C register polling and reduces quiescent current for battery-powered devices. Compared to discrete USB-C implementations using comparators and FETs, the TUSB320L integrates Rp/Rd biasing and accessory detection in a single 1.6 mm x 1.6 mm chip. Typical applications include USB Type-C wall adapters, smartphone charging cradles, accessory-mode audio adapters, USB-C hubs and docks, notebook and tablet Type-C ports, and USB-C debug ports for embedded development. It is widely used wherever a 5 V / up to 3 A Type-C source or sink is needed without USB PD negotiation. A key design tip - because the TUSB320L has no I2C, role selection and current-mode advertisement must be hard-wired through MODE pin resistors at power-up. Layout the CC1/CC2 traces as a 90 ohm differential pair with the connector ground return, and decouple VDD with a 0.1 uF X7R ceramic placed within 2 mm of pin 12. This page synthesizes TI datasheet parameters, distributor pricing, drop-in alternatives (same-brand first, cross-brand verified), and PCB design notes not duplicated in the manufacturer datasheet, giving procurement and design engineers a one-stop reference for the TUSB320LAIRWBR.
TUSB321RWBR - USB Type-C CC Logic 3A X2QFN-12 | Texas Instruments
The Texas Instruments TUSB321RWBR is a USB Type-C configuration channel (CC) logic and port control device with VCONN support, packaged in a 12-pin X2QFN (1.6x1.6 mm) land-grid array. It implements the CC signaling required by USB Type-C Specification 1.1 and remains backward compatible with USB Type-C Specification 1.0, advertising up to 3 A of current through a dedicated current mode pin. A USB Type-C CC logic device is a specialized interface IC that manages the configuration channel pins of a USB Type-C connector. Within the system hierarchy, it sits between the USB Type-C connector and the USB controller or power path, belonging to the interface IC family inside integrated circuits. The CC logic block monitors the CC1 and CC2 pins for pullup or pulldown resistances to determine port attach and detach, cable orientation, and role detection, which are mandatory functions for any Type-C port. Key features include three mode configurations - host only (DFP/Source), device only (UFP/Sink), and dual role port (DRP) - where the device alternates between DFP and UFP roles per the Type-C Specifications. An integrated VCONN switch powers electronically marked (e-marked) cables, and dead battery mode allows a sink device to present as a Type-C device even before system power is available. Technically, the TUSB321 integrates CC termination, Rp/Rd detection, cable orientation indication, and port power control in a single low-power die, minimizing external components and bill-of-materials cost. The compact X2QFN package with 1.6x1.6 mm footprint suits space-constrained portable designs. Typical applications include smartphones, tablets, laptops, docking stations, chargers, and USB Type-C enabled accessories. Any design needing compliant Type-C attach detection and current advertisement benefits from this device. For design, place the TUSB321RWBR close to the Type-C connector to keep CC traces short, decouple VCC with a 1 uF capacitor, and configure the current mode pin for the intended 3 A advertisement level as described in TI datasheet (SLVSDF4).
TUSB321RWBR-Q1 - USB Type-C CC Logic Port Control | TI
The Texas Instruments TUSB321RWBR-Q1 is an automotive-grade USB Type-C configuration channel (CC) logic and port control IC with VCONN support, provided in a compact 12-pin X2QFN package measuring just 1.6 mm x 1.6 mm. Operating from a 4.5V to 5.5V supply, it enables USB Type-C ports with the CC logic needed for Type-C ecosystems while meeting the USB Type-C Specification 1.1 and remaining backward compatible with Specification 1.0. A USB Type-C port controller (also called a CC logic chip or port control IC) is a small companion device that manages the configuration channel pins of a Type-C connector. It sits in the hierarchy: port controller -> USB interface IC -> USB connectivity semiconductor -> power/data management. It detects attach and detach events, determines cable orientation, performs role detection, and advertises current capability through the dedicated current mode pin. Key features include support for up to 3A of current advertisement through the dedicated current mode pin, configurable port roles of DFP (source), UFP (sink), or dual role port (DRP), and integrated VCONN supply switching for actively marked cables. The device autonomously handles Rd/Rp termination switching on the CC pins according to cable orientation, offloading this logic from the system microcontroller. The TUSB321 implements the CC layer with a simple pin-strap configuration (PORT pin) rather than an I2C interface, minimizing firmware complexity and cost for systems that do not need Power Delivery negotiation. Its automotive qualification (AEC-Q100) makes it suitable for infotainment, telematics, and charging ports in vehicles, while the 1.6 mm x 1.6 mm X2QFN footprint fits space-constrained smartphone, tablet, and accessory designs. Typical applications include automotive USB Type-C charging ports, host and device port attach detection in notebooks, docking stations, and power-bank sink/source role management. Design tip: strap the PORT pin for the required role at power-up; if you later need USB Power Delivery negotiation, migrate to the I2C-controlled TUSB322 family, which shares the same X2QFN footprint.
TUSB4041IPAPQ1 - 4-Port USB 2.0 Hub AEC-Q100 | Texas Instruments
The Texas Instruments TUSB4041IPAPQ1 is an automotive-qualified 4-port high-speed 480-Mbps USB 2.0 hub controller in a 64-pin HTQFP (PAP) package with exposed pad. It provides four downstream USB 2.0 ports from a single upstream port, full-speed (12 Mbps), high-speed (480 Mbps), and low-speed (1.5 Mbps) signaling, and operates over -40C to +85C with an automotive-grade qualification. A USB 2.0 hub is a critical interface IC that expands a single USB root port into multiple downstream ports, providing downstream device connect/disconnect detection, overcurrent protection coordination, transaction translation between split USB transactions, and configurable port-power switching. The TUSB4041IPAPQ1 sits in the USB hub controller product hierarchy (USB 2.0 hub -> USB hub -> USB interface IC -> interface IC -> semiconductor) and is widely deployed in automotive infotainment, body electronics, and rear-seat entertainment systems. Key features include integrated USB 2.0 high-speed PHY on every port, pin-strap configuration for battery-charging support, customization via OTP ROM, I2C EEPROM, or I2C/SMBus target interface for VID/PID/port/phy settings, optional upstream port indicator, and individual port power control with overcurrent sensing. The device uses a single 3.3 V supply plus an internal 1.1 V core regulator generated by the on-chip LDO. Internal termination, pull-up/pull-down resistors, and a built-in 5 V VBUS load switch controller (external n-MOSFET required) simplify PCB design. Suspend and remote wakeup signaling are managed in hardware, reducing firmware complexity. Typical applications include automotive head-unit USB ports, rear-seat entertainment hubs, body-control module USB service ports, industrial PC USB expansion, and embedded telematics USB interfaces. AEC-Q100 qualification makes the -Q1 device preferred for road-vehicle applications, while the non-Q1 TUSB4041IPAP serves commercial/industrial environments. When designing with this part, place the external 24.576 MHz crystal (or oscillator) within 5 mm of the XI/XO pins and provide a continuous ground reference under the exposed thermal pad for thermal and EMI performance. Per-port 5 V VBUS switches must use a logic-level n-MOSFET driven by the integrated DP1PWR output to share load-current and fault indications with the host. This page synthesizes distributor pricing for automotive-grade USB hubs, pin-compatible drop-in alternatives, and design considerations from the manufacturer datasheet not always highlighted on distributor listings.
TUSB4041IPAPR - 4-Port USB 2.0 480-Mbps Hub | Texas Instruments
The Texas Instruments TUSB4041IPAPR is a 4-port high-speed 480-Mbps USB 2.0 hub controller in a 64-pin HTQFP (PAP) 10x10 mm package. It provides USB high-speed (480 Mbps) or full-speed (12 Mbps) connections on the upstream port and supports four downstream ports that operate at high-speed, full-speed, or low-speed. The industrial-grade version operates across -40C to +85C, making it suitable for embedded and industrial designs. A USB 2.0 hub controller is a serial-interface bridge that aggregates one upstream USB port into multiple downstream ports while managing the protocol handshakes, transaction translation, and per-port power control dictated by the USB 2.0 specification. It sits within the broader hierarchy of USB controllers -> interface ICs -> power management and connectivity silicon -> mixed-signal semiconductors. The TUSB4041I family supports both self-powered and bus-powered configurations, with integrated USB transceivers and optional battery-charging detection on downstream ports. Key features include 480-Mbps high-speed upstream operation, per-port over-current protection flags, integrated 1.5-kV ESD on USB signal lines, support for compound devices, and I2C/EEPROM configurability for vendor ID (VID), product ID (PID), and port-remap policy. Per-port power-switch control outputs enable ganged or individual port-power switching without external glue logic. The device integrates a UTMI+ low-pin-interface (ULPI) or integrated transceiver variant, a serial-interface engine, and a protocol layer that handles split transactions for full-/low-speed peripherals attached to high-speed upstream links. The HTQFP-64 footprint provides ample ground and power pins for signal-integrity routing on 2-layer consumer-grade boards. Typical applications include USB port expansion on industrial PCs, docking stations, monitors with built-in USB hubs, embedded HMI panels, and POS terminals. The industrial temperature range and integrated charge-detection features also make it a strong fit for automotive-infotainment accessories and medical USB peripherals. When designing with this part, place 27 ohm series termination resistors close to the USB DP/DM pins and provide adequate bulk capacitance on each downstream VBUS rail managed by the controller's power-switch enables.