マイクロコントローラ

製品 (20,000+)

PIC16LF1703-I/ML - 8-bit MCU, 3.5KB Flash, 10-bit ADC | Microchip
PIC16LF1703-I/ML

PIC16LF1703-I/ML - 8-bit MCU, 3.5KB Flash, 10-bit ADC | Microchip

The Microchip Technology PIC16LF1703-I/ML is an 8-bit flash microcontroller built on the enhanced mid-range PIC16 core, combining intelligent analog integration with eXtreme Low Power (XLP) technology in a compact 16-pin QFN-EP (4x4) package. It provides 3.5 KB of Flash program memory, 256 bytes of RAM, and operates from a wide 1.8 V to 3.6 V supply ideal for battery-powered designs, with a maximum CPU clock of 32 MHz delivering 8 MIPS of throughput. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path that integrates a CPU, Flash program memory, RAM, and a rich set of peripherals into one device. Within the broader taxonomy, an 8-bit MCU is a subset of microcontrollers (MCU -> microcontroller -> embedded processor -> semiconductor), which are themselves a category of integrated circuits. The PIC16LF1703 belongs to the PIC16F1xxx family and supports ICSP (In-Circuit Serial Programming) plus in-circuit debugging through two I/O pins, enabling rapid prototyping without removing the device from the board. Key features include a 10-bit ADC with up to 8 channels, two op-amps, a DAC, two comparators, a 16-bit PWM module, and four 8-bit timers, providing high analog integration that traditionally required external components. The XLP technology provides ultra-low sleep current, making the device suitable for energy-harvesting and always-on applications where coin-cell life matters. The PIC16LF1703 uses an enhanced Harvard RISC architecture with a 14-bit instruction word, allowing most instructions to execute in a single 125 ns cycle at 32 MHz. Its peripherals connect via a Peripheral Pin Select (PPS) matrix, simplifying PCB routing by letting designers remap digital functions to any available I/O. Typical applications include IoT sensor nodes, wearables, consumer electronics, smart home devices, and industrial control subsystems. The combination of low power, small footprint, and rich analog integration suits cost-sensitive designs that need a single-chip solution. When designing with this device, ensure your PCB layout reserves the exposed pad (EP) as a thermal and electrical ground, since QFN packages rely on the EP for heat dissipation. Decouple VDD with a 100 nF ceramic capacitor placed within 3 mm of the power pin for stable ADC readings. This page synthesizes verified distributor pricing, drop-in alternatives, AEO-optimized FAQ, and design notes that supplement the manufacturer datasheet with practical, real-world guidance.

見積もり お問い合わせ
PIC16LF1703-I/P - 8-bit 32MHz MCU 3.5KB Flash | Microchip
PIC16LF1703-I/P

PIC16LF1703-I/P - 8-bit 32MHz MCU 3.5KB Flash | Microchip

The Microchip Technology PIC16LF1703-I/P is an 8-bit PIC microcontroller from the PIC16F family built on the company's eXtreme Low Power (XLP) platform, offering a 32 MHz CPU clock, 3.5 KB (2K x 14 words) of Flash program memory and 256 bytes of SRAM in a 14-pin PDIP through-hole package. The 'LF' prefix denotes the 1.8V-3.6V wide-voltage variant optimized for battery-powered applications, while the 'I' suffix indicates the industrial -40C to +85C operating range. The device integrates Core Independent Peripherals including a 10-bit ADC with Computation (ADCC), operational amplifiers, a Capture/Compare/PWM (CCP), Zero-Cross Detect (ZCD), and Peripheral Pin Select (PPS), allowing designers to implement complex analog and timing functions without CPU intervention. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile data memory (SRAM), and a rich set of on-chip peripherals (ADC, timers, communication modules, comparators). Within the broader taxonomy, this PIC16 device sits between 8-bit microcontrollers (PIC10/12/16 families) and 32-bit Cortex-M class devices, providing deterministic instruction execution at low power and ultra-low cost. The PIC16F17XX sub-family targets advanced analog front ends combined with Core Independent Peripherals, a differentiator that distinguishes it from earlier PIC16F baselines and from competitor basic 8-bit MCUs. The PIC16LF1703-I/P's headline features include a 32 MHz maximum internal oscillator, 10-bit resolution ADC up to 35 ksps, two operational amplifiers configurable as comparators or programmable gain amplifiers, Master Synchronous Serial Port (MSSP) supporting I2C and SPI, Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART) with auto-baud detection, and integrated temperature indication diode. The ICSP (In-Circuit Serial Programming) interface allows the device to be programmed directly on the PCB using the MPLAB Snap, PICkit 4, or PICkit 5 debuggers, eliminating socket programming. Typical applications target the analog signal conditioning and low-power sensing segments: wearable fitness bands, smoke and CO detectors, battery-powered sensor hubs with op-amp signal chains, industrial 4-20 mA loop converters, USB charging-cable ID detection dongles, touch/proximity front ends, and small appliance control boards. The XLP architecture's ~30 nA sleep current keeps MCU quiescent consumption negligible in duty-cycled designs where the rest of the system sleeps for the vast majority of time. When designing with the PIC16LF1703-I/P, configure the Configuration Words (FOSC, WDTE, PWRTE, MCLRE, BOR, LVP) before any code can execute, and reserve a 5-pin ICSP header on the PCB for in-circuit programming. Always decouple VDD with a 100 nF plus 1 uF ceramic pair, place decoupling within 3 mm of the supply pins, and follow IPC-7351 PDIP footprint rules with thermal relief spokes for hand/repair soldering.

見積もり お問い合わせ
PIC16LF1703T-I/ML - 8-bit 32MHz MCU 3.5KB Flash QFN-16 | Microchip
PIC16LF1703T-I/ML

PIC16LF1703T-I/ML - 8-bit 32MHz MCU 3.5KB Flash QFN-16 | Microchip

The Microchip Technology PIC16LF1703T-I/ML is an 8-bit PIC16 microcontroller with 3.5KB (2K x 14) Flash program memory housed in a 16-pin QFN (4x4) package with exposed pad, targeting low-power embedded applications. According to the Microchip product page, this device runs at up to 32MHz internal oscillator speed, integrates a 10-bit ADC, and operates from a 1.8V to 3.6V supply, making it part of the eXtreme Low Power (XLP) family. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, Flash program memory, SRAM, and peripherals on one die. The PIC16F/LF family uses Microchip's enhanced mid-range RISC core with 14-bit instruction words, balancing code density, deterministic interrupt response, and ultra-low standby current. Within Microchip's taxonomy, PIC16 sits below PIC18 and dsPIC33 families in performance, above PIC10/12/14/15 in peripheral integration, and competes with AVR ATtiny and low-end STM32G0 devices in cost-sensitive battery-powered designs. Key features include 256 bytes of SRAM, 256 bytes of EEPROM, 12 I/O pins, a 10-bit ADC with up to 8 channels, two 8-bit timers, one 16-bit timer, Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART), and an MSSP (I2C/SPI) peripheral. The XLP nanoWatt technology delivers standby currents below 50 nA typical, making the device suitable for always-on battery applications. The architecture is built around a 14-bit instruction word, single-cycle ALU, and hardware stack with 16 levels, providing predictable real-time behavior. The internal 32MHz oscillator eliminates the need for an external crystal in cost-sensitive designs, while the HFINTOSC supports frequency tuning via the OSCTUNE register for protocols requiring precise baud rates. Typical applications include consumer electronics remote controls, IoT sensor nodes, battery-powered wireless accessories, low-end LED lighting controllers, and small home appliances. The 1.8V minimum supply voltage allows direct connection to single-cell lithium or two-cell alkaline battery chemistries. When designing with this device, engineers should note that the QFN-16 exposed pad must be soldered to the PCB ground plane for proper thermal dissipation and electrical grounding, and that debug/programming requires a dedicated ICSP pinout on PCB pads accessible to the PICkit or MPLAB SNAP programmer. This page synthesizes distributor pricing, drop-in package equivalents, and practical design notes not found in the standalone Microchip datasheet, giving engineers a single reference for evaluation and sourcing.

見積もり お問い合わせ
PIC16LF1703T-I/ST - 8-bit MCU, 3.5KB Flash, 10-bit ADC | Microchip
PIC16LF1703T-I/ST

PIC16LF1703T-I/ST - 8-bit MCU, 3.5KB Flash, 10-bit ADC | Microchip

The Microchip Technology PIC16LF1703T-I/ST is an 8-bit PIC microcontroller (MCU) from the PIC16F family built on an ultra-low-power (XLP) architecture, featuring 3.5KB (2K x 14) of Flash program memory, 256 bytes of SRAM, and 14-bit wide instruction words in a 14-pin TSSOP package. It integrates a 10-bit A/D converter with up to 8 channels, runs at speeds up to 32 MHz, and operates from a wide 1.8V to 3.6V supply thanks to the 'LF' low-voltage process node. The 'T' suffix indicates Tape and Reel packaging, the 'I' indicates the industrial temperature grade (-40C to +85C), and '/ST' denotes the 14-pin TSSOP form factor. A PIC (Peripheral Interface Controller) microcontroller is a small computer-on-a-chip built around a RISC (Reduced Instruction Set Computer) core, on-chip Flash memory, RAM, and a rich set of peripherals including timers, ADC, PWM, and communication interfaces. PIC microcontrollers belong to the broader category of microcontrollers (MCUs), which are a sub-category of microprocessors and embedded processors. PIC16F-series parts sit in the 'mid-range' 8-bit MCU family, offering an attractive balance of cost, peripheral integration, and ease-of-use with the MPLAB X IDE and XC8 C compiler toolchain. Key features of the PIC16LF1703T-I/ST include eXtreme Low Power (XLP) technology with sub-uA sleep currents suitable for energy-harvesting applications, a 10-bit ADC with internal voltage reference and computation features, configurable logic cells (CLC) for hardware-level peripheral customization, complementary waveform generators (CWG) for motor and power control, and multiple communication peripherals including I2C, SPI, and enhanced USART. The device supports in-circuit debugging via MPLAB PICkit and ICD tools. Architecturally, the PIC16LF1703 uses a Harvard RISC core with a 14-bit instruction word and a 32 kHz to 32 MHz internal oscillator, allowing flexible clocking without external crystals. The 10-bit ADC delivers up to 50 ksps conversion rates with hardware post-processing capabilities including averaging and threshold comparisons. The integration of CWG and CLC peripherals enables motor drive, lighting control, and signal generation without external logic ICs. Typical applications for the PIC16LF1703T-I/ST include battery-powered IoT sensor nodes, low-cost consumer electronics with capacitive touch sensing, LED lighting and signage controls, small motor control (fans, pumps), home appliance user interfaces, and industrial sensor conditioning. The combination of XLP sleep modes and integrated analog simplifies battery-powered designs. Designers should evaluate the specific TSSOP-14 pinout availability before selecting this MCU, as the 14-pin footprint limits available I/O to roughly 11-12 general-purpose pins after power and programming pins are accounted for. For higher I/O count requirements, the PIC16LF1703 family also ships in 8-pin DFN, 14-pin SOIC, and 20-pin packages. This page synthesizes distributor pricing, drop-in alternatives, and engineering design notes not available in a single manufacturer datasheet.

見積もり お問い合わせ
PIC16LF1704-E/ML - 8-bit MCU, 7KB Flash, 32MHz, 16-QFN | Microchip
PIC16LF1704-E/ML

PIC16LF1704-E/ML - 8-bit MCU, 7KB Flash, 32MHz, 16-QFN | Microchip

The Microchip Technology PIC16LF1704-E/ML is an 8-bit PIC microcontroller featuring a RISC-based PIC16 CPU core, 7KB (4K x 14) of FLASH program memory, 512 bytes of SRAM, and 128 bytes of data EEPROM. It operates at up to 32MHz and is housed in a 16-pin QFN (4x4 mm) package with an exposed thermal pad. The 'LF' prefix denotes the extended low-voltage (1.8V–3.6V) variant of the PIC16F1704 family, optimized for battery-powered and energy-harvesting designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash for program code, SRAM for data, and often EEPROM for non-volatile storage), and configurable peripherals (ADC, timers, communication ports). Within the broader semiconductor hierarchy, an MCU sits under microcontrollers -> embedded processors -> digital ICs -> semiconductors. The 8-bit PIC16 family from Microchip targets cost-sensitive, low-power embedded control, distinguished from 16-bit dsPIC, 32-bit PIC32, and Arm Cortex-M parts by simpler instruction set, smaller code footprint, and lower unit cost. Key features of the PIC16LF1704 include the XLP (eXtreme Low Power) technology with nanoWatt XLP sleep currents, a 10-bit ADC with computation (ADC2), an 8-bit DAC, two operational amplifiers, a zero-cross detector (ZCD), a comparator, configurable logic cells (CLC), and peripheral pin select (PPS) for flexible signal routing. It supports EUSART, I2C, and SPI communication, plus multiple PWM and CCP/Capture modules. This integration eliminates many external analog components, reducing BOM cost and PCB area. Typical applications include IoT sensor nodes, low-power wireless transmitters, battery chargers, LED lighting controllers, and consumer appliances. The combination of integrated op-amps and a DAC enables closed-loop analog control without external amplifiers. The 1.8V minimum supply supports direct connection to single-cell Li-ion or 2x AA batteries. Designers should note that the 'E' temperature suffix indicates the -40°C to +125°C extended industrial range. The 16-QFN's exposed pad must be soldered to a sufficient copper pour for thermal dissipation. Migrating between PIC16LF1704 family members (different package codes like /ST, /SL, /P) requires only verifying pinout against the datasheet's pin compatibility chart.

見積もり お問い合わせ
PIC16LF1704-E/P - 8-Bit 32MHz XLP MCU 7KB Flash | Microchip
PIC16LF1704-E/P

PIC16LF1704-E/P - 8-Bit 32MHz XLP MCU 7KB Flash | Microchip

The Microchip Technology PIC16LF1704-E/P is an 8-bit RISC microcontroller from the PIC PIC® XLP™ 16F family, delivering 32 MHz CPU performance with 7 KB (4K x 14) of Flash program memory in a 14-pin PDIP through-hole package. It integrates Intelligent Analog peripherals with eXtreme Low Power (XLP) technology, targeting cost-sensitive general-purpose embedded applications. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash), data memory (RAM), and configurable I/O on a single die. The PIC16F170x family specifically targets low-power and mixed-signal embedded designs by combining an 8-bit PIC® RISC core with 12-bit ADC, 8-bit DAC, op-amps, comparators, and Core Independent Peripherals (CIPs), enabling autonomous analog signal conditioning without CPU intervention. The "LF" prefix designates the wide-voltage 1.8V–3.6V variant optimized for battery-powered designs. Key features include 4 KB Flash (7 KB total program space per the 4K x 14 word organization), 512 bytes of RAM, 256 bytes of EEPROM, 12 I/O lines, and an internal 32 MHz oscillator. The 14-pin PDIP package supports breadboard prototyping and hand-soldered designs. On-chip peripherals include 10-bit ADC, 5-/8-/9-bit DAC, two operational amplifiers, two comparators, an 8-bit timer, and enhanced USART, MSSP (SPI/I2C), and EUSART interfaces. Typical applications include IoT sensor nodes, battery-powered consumer devices, LED lighting controllers, capacitive-touch user interfaces, low-cost motor control, and portable medical accessories. The XLP technology provides nanoWatt sleep currents below 100 nA in deep sleep modes, enabling multi-year battery life in standby. When designing with this part, ensure VDD stays within 1.8V–3.6V and reserve a programming/debug pin pair (ICSPCLK/ICSPDAT) accessible to a PICkit programmer. Decouple VDD with a 100 nF ceramic capacitor placed within 5 mm of the IC pins to suppress digital switching transients.

見積もり お問い合わせ
PIC16LF1704-E/SL - 8-bit MCU, 4KB Flash, 32MHz, 14-SOIC | Microchip
PIC16LF1704-E/SL

PIC16LF1704-E/SL - 8-bit MCU, 4KB Flash, 32MHz, 14-SOIC | Microchip

The Microchip PIC16LF1704-E/SL is an 8-bit flash microcontroller from the PIC16F170x/171x family, featuring an eXtreme Low Power (XLP) core that runs up to 32MHz, packs 4KB program memory and 512B RAM, and integrates an intelligent analog peripheral set including a high-speed comparator. The device is housed in a 14-pin SOIC package rated for the automotive -40C to +125C extended temperature window. An 8-bit microcontroller (MCU) is a single-chip processor with an 8-bit data path, on-chip Flash program memory, RAM, peripherals and a CPU optimised for byte-oriented control tasks. Within the broader semiconductor hierarchy, PIC microcontrollers sit under microcontrollers, which are a subcategory of microprocessors and ultimately integrated circuits. The 'LF' prefix in PIC16LF1654-style part numbers designates low-voltage operation (down to 1.8V), which is critical for battery-powered designs. Key features include 7KB total Flash (4K x 14 words), 512B RAM, 10-bit ADC, an 8-bit DAC, two operational amplifiers, a high-speed comparator, and an Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART) plus Master I2C and SPI interfaces. According to the Microchip product page, the XLP technology achieves nanoWatt standby currents that make the part attractive for energy-harvesting and battery-backed sensor nodes. The architecture is built around the enhanced mid-range 16F core with a hardware multiplier and 49 instructions, providing deterministic interrupt latency and a small code footprint. The 32MHz internal oscillator combined with the analog peripherals enables single-chip sensor-conditioning loops without external op-amps or ADC drivers. Typical applications include IoT sensor nodes, LED lighting control, smoke and CO detectors, low-power remote controls, white goods sensor interfaces, and battery chargers with charge-state indication. The wide temperature range also qualifies it for under-hood automotive modules and industrial HVAC controls. The PIC16LF1704-E/SL is supported by MPLAB X IDE, MPLAB Code Configurator, and the XC8 compiler, providing free toolchain access from prototype through production. When designing, leave adequate decoupling (100nF plus 10uF bulk) within 5mm of VDD and AVSS pins, and respect the absolute maximum ratings for VDD to avoid latch-up. This page synthesizes real-time distributor stock, parametric drop-in alternatives and practical design notes that go beyond what the manufacturer datasheet alone provides for the PIC16LF1704-E/SL.

見積もり お問い合わせ
PIC16LF1704-E/ST - 8-bit MCU, 7KB Flash, 32MHz, 14-TSSOP | Microchip
PIC16LF1704-E/ST

PIC16LF1704-E/ST - 8-bit MCU, 7KB Flash, 32MHz, 14-TSSOP | Microchip

The Microchip Technology PIC16LF1704-E/ST is a low-power 8-bit PIC microcontroller from the PIC® XLP™ 16F family, featuring 7KB (4K x 14 words) of Flash program memory, 512 bytes of RAM, and 256 bytes of EEPROM, housed in a 14-pin TSSOP package with a maximum CPU clock of 32MHz. It operates from a 1.8V to 3.6V supply (LF variant) and integrates a rich set of analog and digital peripherals including a 10-bit ADC, an 8-bit DAC, two operational amplifiers (op amps), a high-speed comparator, a zero-cross detect (ZCD), configurable logic cells (CLC), PWM/CCP, and EUSART plus I2C/SPI serial interfaces. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), I/O ports, and peripherals on one die. Within the broader semiconductor taxonomy, the PIC16LF1704 sits in the hierarchy: microcontroller -> embedded processor -> digital IC -> semiconductor. The "LF" suffix denotes the low-voltage (1.8-3.6V) variant of the PIC16F1704 family, optimized for battery-powered and energy-harvesting applications where the XLP™ (eXtreme Low Power) technology delivers nanoWatt sleep currents below 50 nA typical. Key features include four 10-bit PWM channels, two op-amps with internal routing, two high-speed comparators, a 10-bit ADC with up to 8 channels, an 8-bit DAC, and Peripheral Pin Select (PPS) for flexible I/O mapping. The integrated op amps and DAC eliminate the need for external analog ICs in many signal-chain designs, reducing BOM cost and PCB area. PPS allows peripheral signals (UART, SPI, PWM) to be remapped to nearly any digital I/O pin, simplifying PCB layout and package migration. The architecture is a RISC-based enhanced mid-range core with a hardware multiplier, 49 instructions, and a two-deep hardware stack for subroutine nesting. The 32MHz internal oscillator (±1% calibrated) eliminates the need for an external crystal in most applications, saving two PCB components and reducing BOM cost. XLP technology with multiple idle/sleep modes, watchdog timer, and ultra-low-power RTC enables years of operation on a single coin cell. Typical applications include IoT sensor nodes, battery-powered wireless transmitters, LED lighting controllers, small appliance control, portable medical devices, and consumer electronics. The wide 1.8-3.6V range supports direct connection to single-cell Li-ion or two-alkaline-cell battery stacks. The integrated op amps and DAC make it well-suited for closed-loop control of sensors, motor drivers, and lighting. When designing with the PIC16LF1704, plan for programming/debug via the ICSP™ (In-Circuit Serial Programming) interface on pins ICSPCLK/ICSPDAT. A 100nF decoupling capacitor must be placed within 5mm of VDD, and the unused I/O pins should be configured as outputs low to minimize power. The PPS feature must be initialized in firmware before the affected peripherals are enabled. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
PIC16LF1704-I/ML - 8-Bit 32MHz MCU, 7KB Flash, 16-QFN | Microchip
PIC16LF1704-I/ML

PIC16LF1704-I/ML - 8-Bit 32MHz MCU, 7KB Flash, 16-QFN | Microchip

The Microchip Technology PIC16LF1704-I/ML is an 8-bit PIC16 microcontroller from the PIC16LF17xx family that operates up to 32 MHz, integrates 7 KB (4K x 14 words) of Flash program memory and 512 bytes of SRAM, and is housed in a 16-pin QFN (4x4) package. Its headline parameters are 32 MHz CPU clock, 7 KB Flash, and a 16-QFN (4x4 mm) footprint with 0.9 mm profile. An 8-bit microcontroller is a single-chip computer built around an 8-bit data bus and a Harvard or modified-Harvard core that executes one byte per instruction cycle. MCUs sit in the embedded-system hierarchy as follows: microcontroller -> embedded processor -> semiconductor IC, and PIC16 devices specifically belong to the eXtreme Low Power (XLP) PIC16 family optimised for battery applications where every microamp of quiescent current matters. The 'LF' prefix in PIC16LF1704 indicates a wide-voltage core (1.8 V to 3.6 V) tuned for low power; the 'F' family member without 'L' supports higher voltages but draws more current at the same clock. Key features include a 10-bit ADC with computation (ADC2), an 8-bit DAC, two operational amplifiers, two comparators with a 5-bit DAC, two PWM modules with CCP, zero-cross detection (ZCD), configurable logic cells (CLC), peripheral pin select (PPS), and serial interfaces including I2C, SPI, and EUSART. The CLC block is the most distinctive feature because it allows combinational and sequential logic to be implemented in hardware without CPU intervention, which removes software latency from timing-critical signal paths and lowers overall power consumption. Architecturally, the PIC16LF1704 uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word and a hardware stack, complemented by the intelligent analog subsystem that integrates the ADC, DAC, op amps, and comparators on a single die. The 32 MHz operation supports 125 ns minimum instruction cycle, which is enough headroom for digital control loops while leaving the CPU mostly idle for sleep-mode current-sensitive designs. The 4x4 mm QFN package exposes a thermal pad that doubles as the device ground, making PCB layout decisions important for both EMI and thermal performance. Typical applications include low-power IoT sensor nodes, smoke and CO detectors with analog signal conditioning, battery-powered LED lighting controllers with dimming, consumer appliances with capacitive touch, and small motor-control boards that need a single MCU for both logic and analog front-end. In each case the integrated op amps and comparators eliminate external analog ICs. When designing with the PIC16LF1704-I/ML, keep VDD between 1.8 V and 3.6 V, place a 0.1 uF decoupling capacitor within 3 mm of each VDD pin, and connect the exposed pad directly to the ground plane for both thermal dissipation and low-impedance return. Programming requires ICSP via PGC/PGD or the newer MPLAB Snap with a High-Speed USB 2.0 interface. This page synthesises distributor pricing, parametric drop-in alternatives, and design notes for engineers selecting the PIC16LF1704-I/ML, extending the manufacturer datasheet with practical selection guidance not available elsewhere.

見積もり お問い合わせ
PIC16LF1704-I/SL - 8-bit 32MHz 4KB Flash MCU 14-SOIC | Microchip
PIC16LF1704-I/SL

PIC16LF1704-I/SL - 8-bit 32MHz 4KB Flash MCU 14-SOIC | Microchip

The Microchip Technology PIC16LF1704-I/SL is an 8-bit RISC microcontroller from the PIC® XLP™ 16F family, featuring a 32MHz CPU, 7KB (4K x 14) of Flash program memory and 512 bytes of SRAM in a 14-pin SOIC package. The "LF" suffix denotes the low-voltage (1.8V-3.6V) variant of the PIC16F1704, optimized for extreme-low-power (XLP) battery applications. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, a RISC CPU, on-board non-volatile program memory, working RAM, and a set of mixed-signal peripherals. Within the broader semiconductor taxonomy, an MCU belongs to: microcontroller -> embedded processor -> integrated circuit -> semiconductor. The PIC16LF1704 family integrates Intelligent Analog features such as on-chip operational amplifiers, Core Independent Peripherals (CLC, COG, Zero Cross Detect) and Peripheral Pin Select (PPS), placing it in the mid-range "advanced analog" segment of Microchip's PIC16 portfolio. Key features include twelve I/O pins, five timers, two 10-bit PWM channels, a 10-bit ADC with up to twelve channels, two comparators and the XLP sleep current of typically under 50 nA. The 14-pin SOIC footprint (package code SL) gives a small outline through-hole-compatible surface-mount outline with 1.27 mm pin pitch, simplifying hand prototyping and breadboard-friendly adapter boards. Architecture-wise, the device uses the enhanced mid-range PIC16 core with only 49 instructions, hardware stack and a C-compiler-optimized instruction set. The integrated nanoWatt XLP technology, peripheral module disable and idle/doze modes allow the part to maintain RTC-like operation from a coin cell for years. Typical applications include low-power sensor nodes, consumer white goods user-interface panels, LED lighting control, battery-powered IoT endpoints, and small motor/timer controllers. The wide operating range (1.8V-3.6V) suits single-cell Li-ion or 2x AA designs. A typical design uses the on-chip op-amp to condition a sensor signal before ADC sampling, with PPS rerouting peripheral functions to any pin to simplify PCB routing. Always consult the manufacturer datasheet for ADC accuracy, op-amp offset, and absolute maximum ratings before finalizing the BOM. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
PIC16LF1704-I/ST - 8-bit 32MHz XLP MCU 7KB Flash | Microchip
PIC16LF1704-I/ST

PIC16LF1704-I/ST - 8-bit 32MHz XLP MCU 7KB Flash | Microchip

The Microchip Technology PIC16LF1704-I/ST is an 8-bit PIC microcontroller from the PIC16F170x/171x series that combines Intelligent Analog integration with eXtreme Low Power (XLP) technology in a 14-pin TSSOP package. The device operates at up to 32 MHz and includes 7 KB (4K x 14) of Flash program memory, 512 bytes of RAM, and 256 bytes of EEPROM. The "LF" prefix denotes the wide-voltage (1.8V–3.6V) variant, optimized for battery-powered designs. An 8-bit microcontroller (MCU) is a small, self-contained computer-on-a-chip integrating an 8-bit CPU core, Flash program memory, RAM, peripherals, and I/O. The PIC16LF1704 belongs to the PIC16 family → PIC16F170x sub-family → 8-bit PIC MCUs → microcontrollers → microprocessors and microcontrollers → semiconductors. It targets cost-sensitive general-purpose applications where low power consumption is critical, including IoT sensors, consumer electronics, and battery-powered instruments. Key features include a high-speed comparator with 50 ns response time, a 10-bit ADC with computation (ADC2), an 8-bit DAC, two op-amps, up to 17 I/O pins with individually programmable weak pull-ups, and interrupt-on-change capability with edge selection. The XLP technology delivers ultra-low sleep currents in the nanoampere range, enabling multi-year battery life in sensor nodes and remote controls. The PIC16LF1704 employs Microchip's enhanced mid-range core with a 14-bit instruction word and 32 MHz internal oscillator, supporting configurable oscillator modes, two 8-bit timers, and one 16-bit timer. The peripheral pin select (PPS) feature allows flexible remapping of digital peripherals to I/O pins, simplifying PCB layout and enabling compact 14-pin designs. Typical applications include IoT sensor nodes, battery-powered remote controls, low-power sensor interfaces, LED lighting controllers, and small motor control. The device is supported by the MPLAB X IDE and the XC8 compiler, with in-circuit serial programming (ICSP) and in-circuit debugging via the MPLAB Snap or PICkit 4. When designing with this part, verify supply decoupling with at least 0.1 µF ceramic capacitors near the VDD pin, leave unused pins configured as outputs, and respect the 1.8V–3.6V operating range. For lowest sleep current, disable unused peripherals via firmware and select the appropriate low-power sleep mode. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes beyond what the manufacturer datasheet alone offers, helping engineers select the PIC16LF1704 variant that best fits their PCB footprint, voltage budget, and application requirements.

見積もり お問い合わせ
PIC16LF1704T-I/ML - 8-bit MCU, 7KB Flash, 32MHz, 16-QFN | Microchip
PIC16LF1704T-I/ML

PIC16LF1704T-I/ML - 8-bit MCU, 7KB Flash, 32MHz, 16-QFN | Microchip

The Microchip Technology PIC16LF1704T-I/ML is an 8-bit PIC® XLP™ microcontroller delivering 32 MIPS performance from a 32 MHz internal oscillator, packaged in a 16-pin QFN (4x4) with exposed thermal pad. It integrates 7 KB (4K x 14 words) of Flash program memory, 512 bytes of SRAM, and 256 bytes of EEPROM, and is targeted at low-power and mixed-signal embedded designs. A microcontroller (MCU) is a single-chip computer that contains a CPU core, program and data memory, and a rich set of programmable peripherals. The PIC16LF1704 belongs to the PIC16 family of 8-bit microcontrollers built on Microchip's enhanced mid-range core. Within the broader semiconductor taxonomy, it sits in the hierarchy MCU -> microcontroller -> embedded processor -> digital IC -> semiconductor. The 'LF' prefix denotes the wide-voltage, low-power 'F' process technology that supports operation down to 1.8 V. Key features include an integrated 10-bit ADC with up to 8 channels, an 8-bit DAC, two high-speed comparators, an operational amplifier (op-amp) module, zero-crossing detection (ZCD), configurable logic cells (CLC), peripheral pin select (PPS), and both EUSART and I2C/SPI serial interfaces. Capture/Compare/PWM (CCP) and enhanced PWM peripherals support motor and lighting control. According to the manufacturer datasheet, the device draws less than 1 µA in sleep with peripherals active, making it well suited to battery-powered applications. Architecturally, the PIC16LF1704 uses a Harvard RISC core with a 14-bit instruction word and a 32 MHz internal oscillator that requires no external crystal. The on-chip op-amp and DAC enable closed-loop analog control without external amplifiers, reducing BOM cost in sensor-interface and LED-driver designs. PPS allows nearly any digital function to be remapped to most I/O pins, simplifying PCB routing in dense layouts. Typical applications include IoT sensor nodes, wearable health monitors, low-power wireless remotes, LED lighting controllers, and small motor-control boards. The 16-pin QFN (4x4) package suits space-constrained designs. When designing in this part, budget the I/O count carefully - 16 pins share power, ground, programming, and I/O functions, so PPS is helpful but not unlimited. Decouple VDD with a 100 nF ceramic capacitor placed within 3 mm of the pin. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
PIC16LF1704T-I/SL - 8-Bit 32MHz XLP MCU, 4KB Flash | Microchip
PIC16LF1704T-I/SL

PIC16LF1704T-I/SL - 8-Bit 32MHz XLP MCU, 4KB Flash | Microchip

The Microchip Technology PIC16LF1704T-I/SL is an 8-bit PIC microcontroller in the XLP (eXtreme Low Power) family, featuring 7 KB (4K x 14) of Flash program memory, 512 bytes of SRAM, and a maximum CPU clock of 32 MHz, all housed in a 14-pin SOIC (SL) package. As a member of the PIC16F1704 sub-family, it integrates a 10-bit 8-channel Analog-to-Digital Converter (ADC), an 8-bit 1-channel Digital-to-Analog Converter (DAC) with selectable references, plus operational amplifiers and a high-speed comparator — features normally found on larger mid-range parts. An 8-bit microcontroller is a single-chip computer built around an 8-bit data path, popular in embedded control because the architecture is simple, deterministic, and supported by extensive firmware libraries. Within the broader taxonomy, the PIC16LF1704 belongs to PIC microcontrollers -> 8-bit MCUs -> microcontrollers -> microprocessors and microcontrollers -> semiconductors. The 'LF' prefix denotes a wide-voltage 'F' core optimized for low-voltage operation, while XLP technology targets battery-powered products with nanoWatt sleep currents. Key differentiating features include the integrated 8-bit DAC (rare on 14-pin MCUs), Core Independent Peripherals (CIPs) such as the Complementary Waveform Generator (CWG) and Configurable Logic Cell (CLC), 32 MHz operation with 125 ns instruction cycle, and an enhanced mid-range 14-bit instruction set that improves code density over legacy baseline PIC16 cores. The 14-pin SOIC package offers hand-solder-friendly leads while still fitting compact designs. Typical applications include LED lighting controllers (using CWG and DAC for smooth dimming), sensor signal conditioning (using the on-chip op-amps and ADC), battery-powered IoT nodes (using XLP sleep modes), and consumer white-goods user interfaces. The combination of small footprint, on-board analog, and low-power modes makes the PIC16LF1704 particularly attractive for cost-sensitive analog/mixed-signal front-end designs. When designing with this part, plan the oscillator configuration early (the internal 16 MHz HFINTOSC eliminates the need for external crystals in most cases) and reserve one DAC channel for reference generation if your analog signal chain needs a stable bias. The 14-pin SOIC package also requires careful PCB layout to route both analog and digital grounds separately. This page synthesizes distributor pricing across multiple channels, drop-in alternative part numbers from the same PIC16LF1704 family, and practical design notes not consolidated in the manufacturer datasheet — helping procurement and engineering teams make faster, better-informed decisions.

見積もり お問い合わせ
PIC16LF1705-E/P - 8-bit XLP MCU 14KB Flash DIP-14 | Microchip
PIC16LF1705-E/P

PIC16LF1705-E/P - 8-bit XLP MCU 14KB Flash DIP-14 | Microchip

The Microchip PIC16LF1705-E/P is a cost-effective 8-bit PIC RISC microcontroller in the PIC® XLP™ 16F family, featuring 14KB (8K x 14) of Flash program memory, 1024 bytes of RAM, and a 32 MHz internal oscillator core, all integrated into a 14-pin PDIP through-hole package. The device targets general-purpose embedded designs that demand extreme low-power (XLP) operation combined with intelligent analog integration. What is an 8-bit microcontroller? An 8-bit microcontroller (MCU) is a single-chip computer that processes data 8 bits at a time, integrating a CPU core, program memory (Flash), RAM, peripherals, and I/O onto a single die. Within the broader taxonomy, the PIC16LF1705 belongs to the PIC16 family -> 8-bit PIC microcontroller -> microcontroller -> embedded processor -> semiconductor. The 'LF' suffix indicates a low-voltage variant operating down to 1.8V, while 'XLP' (eXtreme Low Power) denotes Microchip's ultra-low-power technology platform designed for battery-operated and energy-harvesting applications. Key differentiating features include on-chip operational amplifiers (op amps), core-independent peripherals such as the Configurable Logic Cell (CLC) and Complementary Output Generator (COG), Peripheral Pin Select (PPS) for flexible signal routing, and Zero-Cross Detect (ZCD). The integrated 10-bit ADC with computation, 8-bit DAC references, and high-speed comparator reduce external component count in mixed-signal designs. Architecturally, the PIC16LF1705 uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word and a hardware stack. The Harvard-style bus separates instruction and data paths, and the device supports in-circuit serial programming (ICSP) plus debug via ICD. Sleep currents in the nanoamp range and multiple low-power modes support years of operation from a single coin cell. Typical applications include consumer appliance control, IoT sensor nodes, LED lighting controllers, battery chargers, smoke and CO detectors, and any cost-sensitive embedded design needing analog integration with low power. The DIP-14 package enables breadboard-friendly prototyping and through-hole assembly. When designing with this device, ensure the configured peripherals stay within the device's 14-pin I/O budget. Use PPS carefully — moving a peripheral away from its default pin can affect boot behavior and debugger mapping. Decouple VDD with a 100 nF ceramic placed within 5 mm of the pin. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with an explicit information-gain layer added on top of Microchip's published specifications.

見積もり お問い合わせ
PIC16LF1705-E/SL - 8-bit 32MHz MCU, 14KB Flash 14-SOIC | Microchip
PIC16LF1705-E/SL

PIC16LF1705-E/SL - 8-bit 32MHz MCU, 14KB Flash 14-SOIC | Microchip

The Microchip Technology PIC16LF1705-E/SL is an 8-bit PIC microcontroller from the PIC16F family with XLP (eXtreme Low Power) technology, offering up to 32 MHz operation, 14 KB Flash program memory (8K x 14) and 1024 bytes of RAM, housed in a 14-pin SOIC (SL) package. The LF prefix denotes the extended low-voltage operating range from 1.8V to 3.6V, making the part suitable for battery-powered and energy-harvesting designs. On-chip peripherals include a 10-bit ADC, configurable logic cells (CLC), complementary output generator (COG), and peripheral pin select (PPS), giving the device an unusual amount of analog and digital integration for its small pin count. An 8-bit microcontroller (MCU) is a programmable logic device that fetches, decodes and executes single-byte instructions stored in non-volatile Flash memory. The PIC16F architecture uses a 14-bit instruction word with separate program and data buses (Harvard architecture) and provides deterministic interrupt response. Positioned inside the broader hierarchy of PIC microcontrollers, this device sits in the XLP mid-range tier that targets very low quiescent current and sleep currents down to the nanoampere range, which is critical for battery lifetime in IoT edge nodes, remote sensors and wearable applications. Key features include 14 KB self-programmable Flash, 1024 bytes SRAM, hardware peripheral pin select for remapping digital peripherals to any I/O pin, up to 32 MHz internal oscillator, and on-chip op-amps. The 10-bit ADC is one of the key differentiating peripherals, allowing direct interface with analog sensors without external analog-front-end components. Together with CLC and COG, the device can implement state-machine logic, signal conditioning and waveform generation in hardware, offloading these tasks from the CPU and reducing firmware complexity. Typical applications include low-power IoT sensor nodes, consumer remote controls, HVAC and small-appliance control, battery chargers, LED lighting drivers and general-purpose 8-bit embedded control. The combination of ultra-low sleep current, peripheral pin select, and integrated analog makes the PIC16LF1705 well suited to designs where PCB area, BOM count and standby power are all constrained. Designers should note that the LF (low-voltage) parts do not run reliably above 3.6V; for higher-voltage rails the non-LF PIC16F1705 variant should be considered. According to the Microchip PIC16(L)F1705/9 datasheet, the device includes an on-chip 32 MHz internal oscillator and supports in-circuit debugging via MPLAB ICD tools.

見積もり お問い合わせ
PIC16LF1705-E/ST - 8-bit MCU, 14KB Flash, 32MHz | Microchip
PIC16LF1705-E/ST

PIC16LF1705-E/ST - 8-bit MCU, 14KB Flash, 32MHz | Microchip

The Microchip Technology PIC16LF1705-E/ST is an 8-bit PIC microcontroller from the PIC16F family built on the eXtreme Low Power (XLP) platform, delivering 32MHz CPU performance with 14KB Flash program memory in a 14-pin TSSOP package. It integrates 1024 bytes of SRAM, 256 bytes of EEPROM, a 10-bit ADC, an 8-bit DAC, operational amplifiers, comparators, CCP/PWM, CLC, ZCD, and PPS in a compact footprint optimized for low-power embedded designs. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that combines a CPU, memory (Flash/ROM for program storage and RAM for data), and peripherals on a single silicon die. The 8-bit data bus means the ALU processes 8 bits per instruction cycle, which is well-matched to bit-oriented control tasks. PIC microcontrollers belong to the MCU family, sit within the broader category of microcontrollers, which are a sub-class of embedded processors, which are themselves a class of semiconductors. The 'LF' suffix indicates low-voltage/low-power operation (1.8V-3.6V), while the 'E' denotes the extended industrial temperature grade (-40C to +125C). Key features include Core Independent Peripherals (CIPs) such as the Configurable Logic Cell (CLC), Complementary Output Generator (COG), Zero-Cross Detection (ZCD), and Peripheral Pin Select (PPS), which offload timing-critical tasks from the CPU. The 10-bit ADC provides up to 8 channels, while the 8-bit DAC enables analog waveform generation without external components. The on-chip operational amplifiers (OPAmp) and high-speed comparators (HS Comp) support signal conditioning in mixed-signal designs. Typical applications include low-power IoT sensor nodes, battery-powered instrumentation, LED lighting control, consumer appliance interfaces, and small-form-factor motor control. The wide operating voltage range (1.8V to 3.6V) and ultra-low XLP sleep currents make it suitable for energy-harvesting and wireless sensor designs where the MCU spends most of its time in sleep mode. When designing with the PIC16LF1705, ensure that unused pins are configured as outputs or tied to known states to minimize current draw, and use PPS to route digital signals to the most convenient physical pins, reducing PCB layout complexity. Always reference the MPLAB X IDE and XC8 compiler toolchain for code development, and validate sleep-mode current consumption against the datasheet's typical and maximum values for your specific VDD and temperature conditions. This page synthesizes distributor pricing, drop-in compatible alternatives from the same PIC16F1705 family, and practical design notes that complement the manufacturer datasheet, providing information gain beyond what is available on distributor product pages alone.

見積もり お問い合わせ
PIC16LF1705-I/ML - 8-Bit XLP MCU, 32MHz, 14KB Flash | Microchip
PIC16LF1705-I/ML

PIC16LF1705-I/ML - 8-Bit XLP MCU, 32MHz, 14KB Flash | Microchip

The Microchip Technology PIC16LF1705-I/ML is an 8-bit PIC16 family microcontroller built on an enhanced mid-range core running up to 32 MHz, integrating 14 KB Flash program memory (8K x 14 words), 1024 bytes of SRAM, and 256 bytes of EEPROM in a 16-pin QFN 4x4 mm package. What is an 8-bit microcontroller? An 8-bit MCU executes instructions on 8-bit data paths and represents one of the most widely deployed classes of microcontrollers in embedded design. It sits within the broader taxonomy of microcontrollers -> microprocessors -> semiconductors. The PIC16LF1705 specifically belongs to the PIC16F family and combines a RISC Harvard architecture with XLP (eXtreme Low Power) technology, well suited to battery-powered and energy-harvesting designs where standby current is critical. Key features include a 10-bit ADC with Computation (ADC2) providing automated averaging, filtering and threshold comparison, two on-chip operational amplifiers (op amps), a 5-bit DAC, two comparators, Core Independent Peripherals (CLC, COG, Zero-Cross Detect), Peripheral Pin Select (PPS) for flexible signal routing, and eXtreme Low Power (XLP) modes with sleep current down to nanoamp levels. The device operates from 1.8 V to 3.6 V on the LF (low-voltage) variant. Internally, the PIC16LF1705 uses a 16-bit instruction word / 8-bit data path Harvard architecture with a 2-stage pipeline, hardware stack, and direct/indirect memory addressing. The integrated op amps, comparators and DAC are tied to the ADC2 pipeline through analog multiplexers, which is what enables many signal-chain tasks (sensor conditioning, threshold detection, waveform generation) to run without CPU intervention - the hallmark of Core Independent Peripherals. Typical applications include battery-powered sensor nodes, IoT edge devices, low-power remote controls, LED lighting controllers, small appliance user interfaces, and 12 V/24 V industrial sensor conditioning boards where the integrated op amps can directly amplify transducer signals before ADC sampling. When designing with this part, place a 100 nF decoupling capacitor as close to the VDD pin as possible and use the PPS feature to remap peripherals away from the few QFN pinouts that are inaccessible on a 16-pin package. Always reserve an MCLR pull-up of approximately 10 kohm unless the internal MCLR is enabled. This page synthesizes distributor pricing, drop-in alternatives and design notes that complement the manufacturer datasheet for engineers sourcing the PIC16LF1705-I/ML on a 16-QFN footprint.

見積もり お問い合わせ
PIC16LF1705-I/P - 8-Bit MCU, 14KB Flash, 32MHz | Microchip
PIC16LF1705-I/P

PIC16LF1705-I/P - 8-Bit MCU, 14KB Flash, 32MHz | Microchip

The Microchip Technology PIC16LF1705-I/P is a cost-effective 8-bit PIC microcontroller featuring a RISC CPU core operating at up to 32MHz, housed in a 14-pin PDIP (0.300 inch, 7.62mm) through-hole package. It integrates 14KB (8K x 14) of self-programmable Flash program memory, 1KB of SRAM data memory, and 128 bytes of data EEPROM, providing a balanced mix of code space and persistent storage for embedded applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (typically Flash), data RAM, peripherals (timers, ADC, communications), and I/O on one die. The PIC16 family uses Microchip's enhanced mid-range 8-bit RISC architecture and falls within the hierarchy: MCU -> 8-bit MCU -> PIC microcontroller -> PIC16 family -> PIC16F/LF170x series. The 'LF' suffix indicates a wide-voltage low-power variant supporting operation down to 1.8V, while 'F' variants typically start at 2.3V, making 'LF' parts preferred for battery-powered or energy-harvesting designs. The PIC16LF1705 integrates Microchip's Intelligent Analog peripherals including on-chip operational amplifiers, a 10-bit ADC with Computation (ADC2), two 8-bit DACs, Core Independent Peripherals (CIPs) such as Configurable Logic Cells (CLC), Complementary Output Generator (COG), Zero-Cross Detect (ZCD), and Peripheral Pin Select (PPS). It supports eXtreme Low Power (XLP) modes including Sleep currents down to approximately 20 nA typical and active currents near 35 uA/MHz at 1 MHz, enabling long battery life in sensor and IoT nodes. Typical applications include low-power IoT sensor nodes, battery-powered measurement instruments, white goods and consumer control panels, LED lighting drivers using the COG and on-chip op-amps, general-purpose motor control, and any cost-sensitive 8-bit embedded control design that requires analog integration without an external op-amp or DAC. The through-hole PDIP-14 package simplifies prototyping, breadboarding, and field replacement versus surface-mount alternatives. When designing with this part, place a 100 nF decoupling capacitor as close as possible to the VDD pin and consider a 10 uF bulk capacitor near the supply rail. Verify that your selected oscillator configuration matches the application speed and power budget, and consult the device datasheet for ADC acquisition-time calculations and FVR stabilization timing.

見積もり お問い合わせ
PIC16LF1705-I/SL - 8-Bit XLP MCU 14KB Flash 14-SOIC | Microchip
PIC16LF1705-I/SL

PIC16LF1705-I/SL - 8-Bit XLP MCU 14KB Flash 14-SOIC | Microchip

The Microchip Technology PIC16LF1705-I/SL is an 8-bit PIC16 microcontroller from the cost-effective PIC® XLP™ 16F family, integrating 14KB (8K x 14) of Flash program memory, 1024 bytes of SRAM, and a 32 MHz internal oscillator in a 14-pin SOIC (SL) package. The LF variant operates across a wide 1.8V to 3.6V supply range and is designed for ultra-low-power (XLP) applications such as battery-powered sensor nodes, IoT edge devices, and energy-harvesting systems. The device features on-chip op amps, a 10-bit ADC, Core Independent Peripherals (CLC, COG/NCO, Zero-Cross Detect), and Peripheral Pin Select (PPS) for design flexibility. An 8-bit microcontroller (MCU) is a compact processor core with on-chip memory and peripherals, optimized for embedded control tasks where low cost, deterministic real-time response, and minimal power consumption outweigh raw computational throughput. The PIC16 architecture sits within the broader Microchip 8-bit hierarchy: PIC10/12/16/18 family → 8-bit MCU → microcontroller → embedded processor → semiconductor. LF variants specifically target the ultra-low-power XLP segment, typically drawing sub-microamp sleep currents suitable for coin-cell and Energy Harvest applications. Key features of the PIC16LF1705 include 32 MHz operation, 14KB Flash with self-programmability, 1024 bytes SRAM, 8-channel 10-bit ADC, two on-chip operational amplifiers, two comparators, an 8-bit DAC, Zero-Cross Detect, Configurable Logic Cells (CLC), Complementary Output Generator (COG), Peripheral Pin Select (PPS), and eXtreme Low Power (XLP) sleep modes. These features are packaged in the 14-pin SOIC footprint for hand-solder-friendly prototyping. Architecturally, the PIC16LF1705 uses a 14-bit instruction-word RISC core with hardware stack, hardware multiplier, and direct/indirect addressing. The Core Independent Peripherals (CLC, COG, Zero-Cross Detect) operate without CPU intervention, reducing latency and power consumption in motor control, lighting, and power-conversion feedback loops. PPS allows peripheral I/O remapping onto most GPIO pins, simplifying PCB layout and BOM. Typical applications include battery-powered IoT sensor nodes, low-cost consumer appliances, LED lighting control with zero-cross detection, small brushed-DC motor control, remote controls, and energy-harvesting wireless switches. The on-chip op amps and comparators make it suitable for analog front-end conditioning without external amplifiers, reducing BOM cost and PCB area in space-constrained designs. When designing with the PIC16LF1705-I/SL, observe the 1.8V to 3.6V supply range, ensure decoupling capacitors (typically 100 nF plus 1 µF bulk) are placed within 5 mm of VDD, and configure unused pins as outputs to minimize sleep current. The PPS feature lets you reassign peripheral outputs to nearly any digital pin, easing layout, but pinout diagrams for the SOIC-14 package remain fixed at the silicon level. This page synthesizes distributor pricing, verified cross-reference drop-in alternatives, and practical design notes not found on the manufacturer datasheet cover page, helping sourcing engineers evaluate second-source options and OEM buyers compare lifecycle risk.

見積もり お問い合わせ
PIC16LF1705-I/ST - 8-bit 32MHz 14KB Flash XLP MCU | Microchip
PIC16LF1705-I/ST

PIC16LF1705-I/ST - 8-bit 32MHz 14KB Flash XLP MCU | Microchip

The Microchip Technology PIC16LF1705-I/ST is an 8-bit PIC® XLP™ 16F microcontroller IC featuring 14KB (8K x 14) of Flash program memory, 1024 bytes of RAM, and a 32 MHz internal core clock, housed in a 14-pin TSSOP package. The part integrates cost-effective Intelligent Analog peripherals including a 10-bit ADC, an operational amplifier (OPAMP), an 8-bit DAC, a high-speed comparator, a zero-cross detect (ZCD), configurable logic cells (CLC), and peripheral pin select (PPS). An 8-bit microcontroller (MCU) is a low-power programmable processor built around an 8-bit data path, well suited to cost-sensitive embedded control. PIC16F170x/171x MCUs combine this 8-bit core with on-chip analog and the eXtreme Low Power (XLP) family of sleep and active modes, occupying a tier in the hierarchy: 8-bit MCU → microcontroller → embedded processor → semiconductor. The 'LF' prefix denotes the wide-voltage 1.8V-3.6V supply variant for battery-powered designs. Key features include 32 MHz max CPU speed from the internal oscillator, 14KB Flash, 1024B SRAM, hardware CLC for combinational/sequential logic without discrete gates, PWM with CCP, and serial interfaces including EUSART, I2C, and SPI. On-chip peripherals such as the 10-bit ADC, op-amp and 8-bit DAC reduce external BOM and PCB area in sensor-interface applications. The architecture combines a RISC-like Harvard core with vectored interrupts and a 14-bit instruction word, enabling compact code density and deterministic interrupt response. PPS allows flexible routing of digital peripherals to any I/O pin, simplifying PCB layout for mixed-signal designs where analog and digital routing would otherwise conflict. Typical applications include IoT sensor nodes, battery-powered instrumentation, LED lighting control, consumer appliances, and low-cost motor control where the integrated op-amp and DAC simplify analog front-ends. Designers commonly pair this MCU with discrete power management and low-power wireless transceivers. When designing with this part, validate current consumption in the chosen sleep mode against battery-life targets: nanoWatt XLP idle currents are well below 1 µA but require correct configuration of the watchdog, brown-out reset and peripheral clocks. PPS remapping must be programmed before peripheral enable to avoid glitches on boot. This page synthesizes distributor pricing, drop-in package-compatible alternatives from the PIC16F170x family, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
PIC16LF1705T-I/ST - 8-bit XLP MCU 14KB Flash 14-TSSOP | Microchip
PIC16LF1705T-I/ST

PIC16LF1705T-I/ST - 8-bit XLP MCU 14KB Flash 14-TSSOP | Microchip

The Microchip Technology PIC16LF1705T-I/ST is an 8-bit PIC® XLP™ microcontroller featuring 14KB (8K x 14) of Flash program memory, 1024 bytes of SRAM, and a 32 MHz internal oscillator, packaged in a 14-pin TSSOP. Operating from 1.8V to 3.6V on the LF (low-power) silicon process, this device targets ultra-low-power embedded applications while integrating rich analog peripherals including a 10-bit ADC, op-amp, 8-bit DAC, comparator, zero-cross detect, and configurable logic cells (CLC). What is a PIC microcontroller? A PIC (Peripheral Interface Controller) is a family of 8-bit RISC microcontrollers originally developed by General Instrument and later popularized by Microchip Technology. Within the broader microcontroller taxonomy, PIC MCUs sit alongside ARM Cortex-M and AVR as the dominant 8/16/32-bit embedded controller architectures. The PIC16F family occupies the "mid-range" tier of Microchip's lineup, balancing cost, peripheral integration, and code density using a 14-bit instruction word and a 5-stage pipeline. The LF suffix denotes the low-Flash/Fowler-Nordheim process variant optimized for lower VDD operation and the proprietary nanoWatt XLP™ (eXtreme Low Power) sleep modes that can drop quiescent current to the nanoamp range. Key features of the PIC16LF1705T-I/ST include Core Independent Peripherals (CIPs) such as CLC, PPS (Peripheral Pin Select), the Numerically Controlled Oscillator (NCO), and Complementary Waveform Generator (CWG). These allow complex signal generation and timing without CPU intervention, freeing the core for system-level tasks. The 10-bit ADC with hardware Capacitive Voltage Divider (CVD) provides touch-sensing capability and averaged acquisition modes, while the integrated op-amp and 8-bit DAC simplify analog front-end designs in sensor conditioning loops. The device also includes Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART) and I2C/SPI interfaces for host communication. Typical applications include IoT sensor nodes, battery-powered consumer electronics, capacitive touch user interfaces, LED lighting controllers, low-end BLDC/PMSM fan control, and small home appliances where the LF process and CIPs reduce BOM cost and firmware complexity. The 32 MHz core delivers roughly 8 MIPS, sufficient for state-machine control loops and simple protocol stacks. When designing with this part, leverage the PPS module to remap digital peripherals to alternative pins—this simplifies PCB routing when only one or two pins are needed on a particular I/O. For lowest sleep power, configure unused peripherals to OFF, enable the FVR (Fixed Voltage Reference) only when needed, and use the RTC with an external 32.768 kHz crystal to time sleep intervals.

見積もり お問い合わせ
PIC16LF1707-E/ML - 8-bit 32MHz XLP MCU 3.5KB Flash 20-QFN | Microchip
PIC16LF1707-E/ML

PIC16LF1707-E/ML - 8-bit 32MHz XLP MCU 3.5KB Flash 20-QFN | Microchip

The Microchip PIC16LF1707-E/ML is an 8-bit PIC® XLP™ flash microcontroller delivering 32 MHz CPU performance with 3.5KB (2K x 14 words) of Flash program memory in a 20-pin QFN (4x4 mm) package. It is part of the PIC16F170X family, which combines Core Independent Peripherals (CIPs) such as Configurable Logic Cells (CLC), Numerically Controlled Oscillator (NCO), and Complementary Waveform Generator (CWG) with an integrated 10-bit ADC and on-chip op-amps. The "LF" prefix indicates the wide-voltage, low-power variant supporting 1.8V to 3.6V operation, while the "-E/" suffix denotes the extended industrial temperature grade of -40°C to +125°C. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and peripheral interfaces onto one silicon die. Within the broader semiconductor taxonomy, an MCU is a subset of microprocessors, which fall under logic ICs and the integrated circuits family. Microchip's PIC® architecture uses a Harvard RISC core with separate program and data buses, and the XLP™ (eXtreme Low Power) designation indicates sleep currents in the nanoamp range - critical for battery-powered and energy-harvesting designs. Key differentiating features of the PIC16LF1707 include the integrated op-amp peripherals that eliminate external analog ICs, 10-bit ADC with computation (ADC2) for automated threshold averaging, and on-chip 5-/8-bit DACs. The device supports up to 18 I/O pins despite its compact 20-QFN footprint, plus peripheral pin select (PPS) for flexible signal routing. The 32 MHz internal oscillator and 4x PLL enable 8 MIPS performance at low power, while the 256 bytes of EEPROM provide non-volatile user data storage. Typical applications span low-power sensor nodes, IoT edge devices, white-goods and appliance controls, LED lighting drivers with analog dimming, and battery-powered instrumentation. The combination of tiny QFN-20 footprint, wide 1.8V-3.6V supply range, and integrated op-amps suits designs where PCB area is at a premium and analog signal conditioning is required near the sensor. When designing with this device, ensure adequate decoupling (100 nF + 1 µF ceramic) within 5 mm of the VDD pin and use the on-chip debug (ICD) interface for in-circuit programming. For noise-sensitive analog paths, place the device's exposed thermal pad (EP) to a grounded copper pour to reduce both thermal resistance and ground bounce on the analog supply rail. This page synthesizes distributor pricing, drop-in alternatives within the PIC16LF170x family, and practical design notes not found in the manufacturer's datasheet - giving you selection clarity for the PIC16LF1707-E/ML in compact, low-power embedded designs.

見積もり お問い合わせ
PIC16LF1707-E/P - 8-bit 32MHz 3.5KB Flash MCU | Microchip DIP-20
PIC16LF1707-E/P

PIC16LF1707-E/P - 8-bit 32MHz 3.5KB Flash MCU | Microchip DIP-20

The Microchip Technology PIC16LF1707-E/P is an 8-bit PIC16 family flash microcontroller running up to 32 MHz with 3.5 KB (2K x 14) of program Flash memory, housed in a 20-pin PDIP (0.300 inch, 7.62 mm) through-hole package. The "LF" prefix denotes the wide-voltage XLP (eXtreme Low Power) variant, capable of operating across 1.8V to 3.6V from a single Li-ion / two-AA cell stack, while the "E" suffix specifies the -40C to +125C extended operating temperature grade for automotive and industrial environments. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and peripherals such as timers, ADC, communication interfaces, and I/O on one silicon die. PIC16F/LF170x parts belong to the "PIC16F1xxx enhanced mid-range" family and pair an 8-bit RISC core with Core Independent Peripherals (CIPs) that offload tasks like signal generation, complementary waveform timing, and event-triggered capture from the CPU, lowering interrupt latency and total power. The PIC16LF1707-E/P sits within the power-management IC family hierarchy MCU -> microcontroller -> 8-bit MCU -> PIC16F/LF family -> XLP variants, and is the smallest Flash member of the 170x series in PDIP-20. Key differentiating features include integrated op-amps, a 10-bit ADC with computation (ADC2), a 5/8-bit DAC, two high-speed comparators, an 8-bit timer, a 16-bit timer, and PWM/SMT/CWG/CCP modules, all in a 20-pin footprint. Internal 32 MHz oscillator accuracy supports UART-baud-rate generation without an external crystal in many designs. XLP technology typically delivers < 50 nA sleep current and active currents in the tens of microamperes per MHz, allowing years of operation from a coin cell. Architecturally, the device uses a 14-bit instruction word with a hardware multiplier, a 17-deep stack, and 256 bytes of RAM, with 128 bytes of EEPROM for non-volatile data storage. The Harvard architecture separates program and data buses, enabling single-cycle instruction fetch and improving deterministic real-time response. Core Independent Peripherals reduce firmware complexity by handling timing-critical sequences in hardware, leaving the CPU free for state-machine logic. Typical applications include battery-powered sensor nodes, IoT edge nodes, LED lighting controllers, low-cost consumer appliances, automotive body electronics (when ordered in automotive-qualified grades), and industrial control loops that benefit from on-chip op-amps and comparators. The extended temperature range supports under-hood and outdoor enclosures. When designing with this part, plan decoupling: place a 100 nF ceramic bypass capacitor within 2 mm of VDD and a bulk capacitor on the MCLR/VPP/VDD rails. Verify ICD programming-pin mapping against the chosen package and reserve a 2-pin header for in-circuit serial programming (ICSP) so firmware can be updated without removing the chip. This page synthesizes distributor pricing for the PIC16LF1707-E/P, Microchip 20-pin PDIP drop-in equivalents, and practical design notes (decoupling, ICSP, sleep-mode current budgets) that are not bundled into the manufacturer datasheet.

見積もり お問い合わせ
PIC16LF1707-E/SO - 8-bit MCU, 3.5KB Flash, 32MHz | Microchip
PIC16LF1707-E/SO

PIC16LF1707-E/SO - 8-bit MCU, 3.5KB Flash, 32MHz | Microchip

The Microchip Technology PIC16LF1707-E/SO is an 8-bit Flash microcontroller from the PIC16F170x/171x family, offering 3.5KB (2K x 14) of program memory, 256 bytes of SRAM, and 128 bytes of EEPROM in a 20-pin SOIC package. Built on an enhanced mid-range core, it operates up to 32MHz instruction cycle and supports a wide supply voltage range from 1.8V to 3.6V, making it ideal for battery-powered applications. The device integrates a 10-bit ADC, two op-amps, two comparators, a 4-channel PWM module, and a 17 I/O pin capability. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data bus, used to sense, decide, and actuate in embedded systems. The PIC16LF1707-E/SO belongs to the broader hierarchy of microcontroller -> 8-bit MCU -> Flash MCU -> low-power MCU, optimized for cost-sensitive general-purpose applications requiring minimal power consumption. The 'LF' prefix denotes the low-power 'F' (Flash) variant supporting down to 1.8V operation, while 'XLP' branding reflects Microchip's eXtreme Low Power technology platform. Key features of this part include an integrated 10-bit Analog-to-Digital Converter (ADC), two operational amplifiers (op-amps) that can be configured as rail-to-rail stages, and a peripheral pin select (PPS) mechanism that allows flexible function-to-pin mapping. The on-chip 4-channel Capture/Compare/PWM (CCP) module handles motor control or LED dimming, while the Numerically Controlled Oscillator (NCO) provides precision frequency generation for timing-sensitive applications. CIP (Core Independent Peripherals) like CWG, NCO, and CCL let designers implement complex logic without CPU intervention. Typical applications span IoT sensor nodes, battery-powered remote controls, low-cost motor drivers, LED lighting controllers, and consumer appliances where small pin count, low quiescent current, and integrated analog peripherals reduce BOM cost. The -40C to +125C extended temperature grade (-E suffix) ensures operation in harsh industrial environments. Designers familiar with MPLAB X IDE and XC8 compiler can program and debug this part using PICkit programmers or Curiosity development boards. When selecting the PIC16LF1707-E/SO, prioritize it for designs requiring small 8-bit footprint with on-board op-amps and ADC. If your application needs more I/O or larger memory, consider the PIC16LF1708/1709 family. The SOIC-20 wide-body package (7.50mm width) offers robust handling for hand-prototyping and through-hole conversions with carrier boards.

見積もり お問い合わせ