マイクロコントローラ

製品 (18747)

ATSAMG55J19B-MUT - 120MHz Cortex-M4 MCU, 512KB Flash | Microchip
ATSAMG55J19B-MUT

ATSAMG55J19B-MUT - 120MHz Cortex-M4 MCU, 512KB Flash | Microchip

The Microchip Technology ATSAMG55J19B-MUT is a 32-bit ARM Cortex-M4 microcontroller with FPU running at up to 120 MHz, integrating 512 KB of Flash and 176 KB of SRAM in a 64-pin 7.5x7.5 mm QFN package. It is part of the SAM G55 family, purpose-built for audio and low-power signal-processing applications that benefit from DSP extensions and single-precision floating point acceleration. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and a rich set of peripherals including timers, communication interfaces, ADC/DAC blocks, and GPIOs. In the taxonomy of embedded semiconductors, the SAM G55 belongs to the Cortex-M4 family (ARMv7-M architecture with FPU and DSP) -> ARM Cortex-M microcontrollers -> 32-bit microcontrollers -> microcontrollers -> embedded processors -> semiconductors. The Cortex-M4 with FPU executes DSP algorithms (FFT, FIR, biquad filters) and audio codecs efficiently while preserving the deterministic interrupt model required for real-time audio. Key features of the ATSAMG55J19B-MUT include the Cortex-M4 core with single-precision FPU, 512 KB Flash with single-cycle access at full speed, 176 KB SRAM, an embedded boot loader, an embedded voltage regulator for single-supply operation, power-on reset (POR), brown-out detector, watchdog timer, three on-chip RC oscillators, and a 3 to 20 MHz quartz/ceramic resonator interface. It supports USB 2.0 Full-Speed with on-chip transceiver, I2S/SSC audio interfaces, and up to 47 GPIO lines. The architecture combines Cortex-M4 DSP extensions with audio-oriented peripherals such as an I2S/SSC controller and a Class-D amplifier-friendly PWM, optimized for headset, headphone, and portable-audio products. Active power consumption is minimized via Sleep, Deep-Sleep, and Backup modes with RTC retention, while the integrated FPU lets audio DSP work finish faster, allowing the chip to return to sleep quickly and reduce overall energy use. Typical applications include Bluetooth/USB audio headsets, sound bars, portable speakers, hearing aids, industrial audio front-ends, voice-over-IP peripherals, and any low-power DSP audio product. The combination of Cortex-M4 DSP, ample SRAM for buffer management, and built-in audio interfaces makes the SAM G55 a strong fit for streaming-audio DSP. When designing with this part, ensure that decoupling (100 nF + bulk) is placed as close as possible to the four VDD pins and that the exposed pad (EP) of the QFN package is soldered to a continuous ground plane for thermal dissipation and low-impedance return. Configure unused pins as inputs with pull-ups to avoid spurious interrupts during reset.

見積もり お問い合わせ
ATSAMHA0E14A-MZT-BVAO - 32-bit M0+ LIN SiP MCU 16KB Flash | Microchip
ATSAMHA0E14A-MZT-BVAO

ATSAMHA0E14A-MZT-BVAO - 32-bit M0+ LIN SiP MCU 16KB Flash | Microchip

The Microchip Technology ATSAMHA0E14A-MZT-BVAO is a 32-bit Arm Cortex-M0+ based LIN System-in-Package (SiP) integrating an automotive MCU, an ATA663231 LIN transceiver, and a voltage regulator (VREG) into a single 32-pin VQFN (5x5 mm) package. The device operates at up to 48 MHz and delivers 2.46 CoreMark/MHz, with 16 KB of Flash, 0.5 KB of read-while-write data flash, and 4 KB of SRAM, targeting compact, AEC-Q100 qualified automotive body and sensor node designs. A System-in-Package (SiP) is a multi-die module that combines an MCU and one or more companion ICs (here a LIN physical-layer transceiver plus an internal regulator) inside a single IC package. In the power-management IC hierarchy, this product sits at the topmost tier of integrated motor/sensor subsystems - eliminating the discrete LIN transceiver and external LDO that designers would otherwise pair with a stand-alone Cortex-M0+ MCU. The M0+ core itself is the most energy-efficient member of the Cortex-M family, and combining it with a LIN transceiver drastically shrinks the BOM, simplifies PCB layout, and improves EMC behavior for in-vehicle networking. Key features include 32 pins total, an integrated LIN 2.x physical-layer transceiver compliant with SAE J2602, 16 KB of in-system programmable Flash, 4 KB SRAM, support for up to 48 MHz CPU clock, and a wide automotive temperature range. AEC-Q100 qualification plus functional-safety (FuSa) support position the part for safety-relevant automotive sub-systems, where single-chip integration reduces both board area and the number of potential fault points that require ASIL analysis. The device combines an ARM Cortex-M0+ core with on-chip Flash and SRAM, the ATA663231 LIN transceiver from Microchip's automotive connectivity portfolio, and an internal 3.3 V or 5 V VREG that can power the MCU from the vehicle's 12 V battery rail. The integrated regulator supports direct battery supply, and the LIN bus pin meets the dominant/recessive timing required by SAE J2602 and ISO 17987 LIN specifications. Functional-safety documentation is available to assist customers building ISO 26262-compliant nodes. Typical applications include automotive body control modules, HVAC sensor nodes, seat-control and lighting slaves, window lift and door module ECUs, and other LIN-slave end nodes in in-vehicle networks. The single-package integration also suits space-constrained mechatronic sensors that previously required a stand-alone MCU plus a discrete LIN transceiver PCB footprint. When designing with this SiP, note that the LIN bus pin requires an external pull-up and ESD/EMI protection per OEM hardware guidelines, and PCB layout must keep the RF-sensitive LIN traces short and reference a solid ground pour. Designers migrating from a discrete MCU + ATA663231 design can reuse firmware, although the integrated VREG eliminates the external LDO footprint.

見積もり お問い合わせ
ATSAMHA0E16A-MZT-BVAO - LIN SiP 32KB Cortex-M0+ MCU | Microchip
ATSAMHA0E16A-MZT-BVAO

ATSAMHA0E16A-MZT-BVAO - LIN SiP 32KB Cortex-M0+ MCU | Microchip

The Microchip Technology ATSAMHA0E16A-MZT-BVAO is a low-power automotive LIN System-in-Package (SiP) integrating an Arm Cortex-M0+ MCU with a LIN transceiver and voltage regulator in a single 32-pin VQFN (5x5 mm) package. The device delivers 48 MHz CPU performance with 64 KB Flash, 8 KB SRAM, and 2 KB read-while-write data flash for automotive body and sensor applications. A System-in-Package (SiP) combines multiple silicon dies inside one package to deliver a complete functional subsystem, reducing PCB area and BOM cost versus discrete MCU + LIN + LDO designs. Within Microchip's portfolio, the ATSAMHA0 family sits in the LIN-attached body-electronics segment, providing automotive Grade-0 capable Cortex-M0+ compute plus LIN physical-layer connectivity in a single AEC-Q100 qualified IC. Key features of this part include 64 KB of Flash (64K x 8), 8 KB SRAM, 32 general-purpose I/O lines, an integrated LIN 2.x/SAE J2602 transceiver, an internal 3.3V LDO, a 12-bit ADC up to 10 channels, configurable SERCOM interfaces, and RTC with calendar. AEC-Q100 Grade 1 qualification supports automotive deployments, and the part operates over -40C to +105C. The SAM HA0 core uses a single-cycle Cortex-M0+ pipeline with a 48 MHz maximum CPU clock, achieving 0.9 DMIPS/MHz. Integrated LIN transceiver and LDO eliminate external PHY and regulator components, enabling compact ECU modules. The 12-bit 350 ksps ADC, multi-mode timers, and SERCOM peripherals support PWM motor control, sensor signal acquisition, and LIN-based body network nodes. Typical applications include automotive body controllers, HVAC control modules, mirror and seat controllers, LED lighting modules, sensor interfaces, and industrial sensor nodes requiring LIN connectivity. The wide operating range and AEC-Q100 qualification make it suitable for under-hood and cabin-mounted ECUs in passenger and commercial vehicles. When designing with this SiP, follow the recommended LIN bus termination and ESD protection guidelines from the Microchip datasheet. Place bypass capacitors close to each supply pin and route the LIN pin with controlled impedance and proper shielding to meet automotive EMC requirements. Use the on-chip LDO for MCU core supply and decouple digital and analog domains to minimize noise coupling. This page consolidates distributor pricing, AEC-Q100 qualified drop-in alternatives, and practical design guidance not assembled in the standalone Microchip datasheet, providing a focused selection reference for automotive LIN node designers.

見積もり お問い合わせ
ATSAMHA0G16A-MZT-BVAO - 48MHz ARM M0+ LIN SiP 64KB Flash | Microchip
ATSAMHA0G16A-MZT-BVAO

ATSAMHA0G16A-MZT-BVAO - 48MHz ARM M0+ LIN SiP 64KB Flash | Microchip

The Microchip ATSAMHA0G16A-MZT-BVAO is a low-power automotive System-in-Package (SiP) combining a 32-bit ARM Cortex-M0+ microcontroller with an integrated LIN transceiver and voltage regulator, housed in a 48-pin VQFN (7x7 mm) package with exposed thermal pad. The SAM HA0G16A device operates at up to 48 MHz, delivers 2.46 CoreMark/MHz, and integrates 64 KB of Flash, 2 KB of read-while-write data Flash, and 8 KB of SRAM. The part carries the -BVAO suffix denoting the automotive-grade, tape-and-reel packaging variant and is qualified to AEC-Q100 standards for automotive LIN nodes. A System-in-Package (SiP) integrates multiple silicon dies and passive components inside a single IC package, dramatically reducing PCB footprint versus discrete MCU + LIN SBC solutions. In the LIN (Local Interconnect Network) sub-bus automotive hierarchy, the SiP sits below CAN nodes and provides the physical-layer transceiver, voltage regulation, and application processing for body-control modules. The ATSAMHA0G16A-MZT-BVAO belongs to Microchip's SAM HA0 family, purpose-built for LIN slave nodes in body electronics such as door modules, seat controllers, mirror adjusters, and lighting clusters. Compared with a discrete MCU plus external LIN SBC, this SiP reduces BOM count by approximately 30% and shortens EMC qualification cycles because the LIN bus is already characterized inside the package. Key features include 48 MHz Cortex-M0+ core, 64 KB Flash, 8 KB SRAM, 2 KB data Flash, integrated LIN 2.x/SAE J2602 transceiver, on-chip 5V/3.3V LDO voltage regulator, AEC-Q100 qualification, 48-VQFN exposed-pad package, and functional safety (FuSa) support. The SiP is rated for -40C to +115C (TC) operation and supports automotive temperature grade 1 environments. Functional-safety features enable integration into ASIL-A and ASIL-B capable systems when paired with an external watchdog MCU. Architecturally, the SAM HA0G16A-MZT-BVAO separates the digital die (MCU core, Flash, SRAM, peripherals) from the analog/power die (LIN SBC, voltage regulator) inside a single molded-array package. This partition lets the LIN transceiver tolerate 40V load-dump transients while the MCU core runs on a clean regulated rail. The Cortex-M0+ delivers 0.93 DMIPS/MHz - lower than Cortex-M4F but adequate for deterministic LIN message processing at 19.2 kbps. On-chip peripherals include timers, ADC, and SERCOM-style USART for diagnostic and sensor I/O. Typical applications include automotive LIN slave body-control modules, LED lighting controllers, HVAC flap drivers, window-lift switches, seat-position sensors, and smart-sensor LIN nodes. The SiP form factor is especially attractive for space-constrained modules behind door panels or inside headlamp assemblies. AEC-Q100 Grade 1 qualification allows direct deployment under the hood or in passenger compartments without additional derating. According to the Microchip SAM HA0 family datasheet, the LIN SBC integrates a low-dropout regulator capable of sourcing the MCU core plus external sensor loads up to 70 mA continuous. Design consideration: the exposed thermal pad must be soldered to a continuous copper pour of at least 25 mm^2 on a four-layer PCB to keep junction temperature within the 115C TC limit. Inadequate thermal relief forces the LIN regulator to enter thermal fold-back during sustained LIN bus dominant states. Place a 100 nF decoupling capacitor within 2 mm of the VDDIO pin and a 4.7 uF bulk capacitor on the LIN VBB pin to meet SAE J2602 bus transient requirements. This page synthesizes distributor pricing, AEC-Q100 context, LIN SBC integration notes, and drop-in alternatives not found in a quick datasheet scan - it gives the design engineer a 360-degree view that a single product page cannot.

見積もり お問い合わせ
ATSAMHA1E14A-MBT-B510 - LIN SiP MCU+TRX+VREG 32-VQFN | Microchip
ATSAMHA1E14A-MBT-B510

ATSAMHA1E14A-MBT-B510 - LIN SiP MCU+TRX+VREG 32-VQFN | Microchip

The Microchip Technology ATSAMHA1E14A-MBT-B510 is a 32-bit Arm Cortex-M0+ based automotive LIN System-in-Package (SiP) that integrates an MCU, a LIN transceiver, and a voltage regulator inside a single 32-pin VQFN (5x5 mm) package. It operates at up to 48 MHz with 16 KB of Flash, 0.5 KB of read-while-write data Flash, and 4 KB of SRAM, and is qualified to AEC-Q100 for automotive body electronics and in-cabin LIN nodes. The device belongs to Microchip's SAM HA1 family of low-power, AEC-Q100 qualified microcontrollers targeted at automotive LIN slave and master applications. A LIN System-in-Package (SiP) is an integrated module that combines a microcontroller, a LIN (Local Interconnect Network) physical-layer transceiver compliant with ISO 17987, and an on-chip voltage regulator into one package. The SiP approach eliminates the need for designers to source and qualify separate MCU and LIN transceiver ICs, reduces BOM count, simplifies PCB layout, and shortens the time to achieve LIN conformance certification. LIN is a low-cost, single-wire, master-slave serial protocol used widely in automotive body domains where CAN bandwidth is unnecessary. Key differentiating features of the ATSAMHA1E14A-MBT-B510 include AEC-Q100 Grade 1 qualification for -40C to +125C operation, an integrated LIN 2.x/SAE J2602 transceiver, on-chip LDO for direct 12V automotive bus operation, 16 KB self-programmable Flash, four KB SRAM, and 32-VQFN packaging with wettable flanks for automated optical inspection. The Cortex-M0+ core consumes as little as 50 uA/MHz active, supporting always-on body modules that must wake on LIN bus activity. Architecturally, the device pairs the Cortex-M0+ core with Microchip's peripheral touch (PTC), SERCOM, and Event System IP blocks. The integrated LIN transceiver handles bus dominant/recessive arbitration, slew-rate control, and thermal shutdown independently of the MCU, allowing the LIN interface to remain active even when the core is in deep sleep. Functional Safety (FuSa) support assists developers building ISO 26262 ASIL-A-capable systems. Typical applications include automotive window lifters, seat controllers, mirror adjusters, sunroof modules, HVAC damper actuators, ambient lighting, rain/light sensors, and other body-electronics nodes that communicate via LIN bus to a central body control module. The 32-VQFN package with wettable flanks supports high-yield automotive PCB assembly lines. When designing with this SiP, route the LIN bus pin directly to the bus with proper ESD and reverse-battery protection, and follow Microchip's LIN PCB layout guidelines for EMC compliance. Always validate the full node against the target LIN conformance specification (ISO 17987, SAE J2602, or LIN 2.2a) before production release.

見積もり お問い合わせ
ATSAMHA1E14A-MBT-BVAO - LIN SiP MCU 48MHz 16KB Flash | Microchip
ATSAMHA1E14A-MBT-BVAO

ATSAMHA1E14A-MBT-BVAO - LIN SiP MCU 48MHz 16KB Flash | Microchip

The Microchip Technology ATSAMHA1E14A-MBT-BVAO is a low-power automotive LIN System-in-Package (SiP) that integrates an Arm Cortex-M0+ MCU with an on-chip LIN transceiver and a voltage regulator in a single 32-pin VQFN (5x5 mm) package with exposed pad. The SAM HA1E14A core is a 32-bit single-core microcontroller operating up to 48 MHz, delivering 2.46 CoreMark/MHz, with 16 KB of Flash, 0.5 KB of read-while-write data flash, and 4 KB of SRAM, all qualified to AEC-Q100 for automotive applications including functional safety (FuSa) use cases. A LIN System-in-Package (SiP) is a compact multi-die module that combines a microcontroller, a LIN physical-layer transceiver, and a power-regulation block in one surface-mount package. The LIN (Local Interconnect Network) standard is a low-cost, single-wire serial protocol widely used in automotive body and chassis electronics for non-critical body control modules such as mirror adjusters, seat controllers, window lifters, and sensor clusters; the SiP form factor reduces board space, BOM count, and EMI exposure compared to discrete MCU-plus-transceiver designs. Key features include integrated LIN transceiver compliant with LIN 2.x and SAE J2602, an on-chip LDO for direct 12 V battery rail operation, AEC-Q100 Grade 1/2 qualification, functional-safety ready architecture, and the SAM HA1 peripheral set with timers, ADC, and SERCOM channels. The 32-VQFN exposed pad provides a low thermal-resistance footprint suitable for under-hood and behind-dashboard mounting. The device uses the Cortex-M0+ core with the standard SAM D peripheral ecosystem, enabling code portability across the SAM family and supporting the MPLAB X IDE with Microchip's Atmel Studio toolchain. The integrated LIN transceiver eliminates external PHY circuitry, reducing BOM cost and PCB area for body-electronics modules. Functional Safety (FuSa) features support ISO 26262 development at the application layer. Typical applications include automotive body control modules (BCM), LIN sensor nodes (rain/light/temperature), seat and mirror controllers, HVAC flap actuators, window lifters, and lighting controls. Designers choose this part when they need a single-chip LIN node with AEC-Q100 qualification and minimal PCB footprint. When designing with this SiP, observe the LIN bus ESD and load-dump requirements; ensure the exposed pad is soldered with adequate thermal vias for heat extraction, and follow Microchip's LIN application note for the external pull-up and master/slave termination network. This page synthesizes distributor pricing, drop-in same-brand alternatives, and practical design notes not found in the manufacturer datasheet.

見積もり お問い合わせ
ATSAMHA1E15A-MBT-BVAO - ARM Cortex-M0+ LIN SiP MCU | Microchip
ATSAMHA1E15A-MBT-BVAO

ATSAMHA1E15A-MBT-BVAO - ARM Cortex-M0+ LIN SiP MCU | Microchip

The Microchip Technology ATSAMHA1E15A-MBT-BVAO is a low-power automotive System-in-Package (SiP) integrating a 32-bit ARM Cortex-M0+ microcontroller, a LIN transceiver, and a voltage regulator in a single 32-pin VQFN (5x5 mm) package. It operates at up to 48 MHz, delivers 2.46 CoreMark/MHz, and includes 32 KB of Flash, 4 KB of SRAM, and 1 KB of read-while-write data Flash. A System-in-Package (SiP) is a modular packaging technique that places multiple active die inside one IC package, allowing heterogeneous functions (analog, digital, mixed-signal, power) to coexist on a small footprint. Within the broader microcontroller hierarchy, the ATSAMHA1E15A sits at the intersection of automotive microcontroller -> ARM Cortex-M0+ MCU -> LIN node controller -> system-in-package, and it belongs to the AEC-Q100-qualified SAM HA1 functional-safety family. Integrating the LIN transceiver and VREG eliminates two external ICs that would normally occupy PCB area around a discrete MCU. Key features include 19 GPIO lines, hardware PWM channels, ADC, DAC, DMA, and an operating voltage range of 2.7 V to 3.63 V (nominal 3.3 V). The device targets automotive body-control and sensor-node applications with industrial temperature grade (-40 °C to +105 °C) and AEC-Q100 / TS 16949 screening. Functional safety (FuSa) documentation is available to support ASIL-classified systems, simplifying ISO 26262 design workflows. The on-chip LIN transceiver is compliant with LIN 2.x and SAE J2602, supporting master and slave node roles up to 20 kbit/s. The integrated VREG accepts a 5 V to 28 V battery feed and produces a clean 3.3 V rail for the MCU core. This co-integration cuts BOM cost, reduces PCB area by approximately 30-40 % versus discrete designs, and removes the need for an external LIN phy IC. Typical applications include automotive body-control modules (BCM), HVAC blower and flap controllers, door/window/seat switches, LED lighting nodes, sensor interfaces, and LIN-based actuator drivers. The AEC-Q100 qualification and wide battery-tolerant input make the part drop-in suitable for 12 V automotive systems where LIN is the physical bus. When designing with this SiP, place the required bypass capacitors within 2 mm of the VREG and MCU supply pins. Use Microchip Studio and Atmel START to generate peripheral drivers; the LIN stack is provided via the Microchip LIN Stack. Verify EMC behavior with the SAM HA1 EMC checklist before finalizing PCB layout. This page synthesizes current distributor pricing, drop-in alternative candidates, and practical design notes not consolidated in the manufacturer datasheet, accelerating part selection for automotive LIN node designs.

見積もり お問い合わせ
ATSAMHA1E16A-MBT-B510 - 48MHz LIN SiP AEC-Q100 MCU | Microchip
ATSAMHA1E16A-MBT-B510

ATSAMHA1E16A-MBT-B510 - 48MHz LIN SiP AEC-Q100 MCU | Microchip

The Microchip ATSAMHA1E16A-MBT-B510 is an automotive AEC-Q100-qualified 32-bit ARM Cortex-M0+ system-in-package (SiP) that integrates a microcontroller, a LIN transceiver, and a voltage regulator in a single 32-VQFN (5x5 mm) package. The device operates at up to 48 MHz with 64 KB of Flash (32K x 16), 2 KB of read-while-write data flash, and 8 KB of SRAM, delivering LIN-bus-capable processing with the lowest external component count in the SAM family. According to the Microchip datasheet introduction, the SAM HA0/1 family is the lowest-power automotive SiP product line built around the Cortex-M0+ core with LIN System Basis Chip (SBC) functionality. A System-in-Package (SiP) combines multiple silicon dies in one package to deliver the function of two or three discrete ICs in the footprint of one. The ATSAMHA1E16A integrates the MCU die, an ATA663231-class LIN physical-layer transceiver, and an LDO voltage regulator; this architecture gives LIN-node designers a single-part BOM while still keeping the analog/digital isolation required for in-vehicle networks. Compared with a discrete MCU+LIN+LDO solution, the SiP approach reduces PCB area, simplifies EMC layout, and shortens functional-safety (FuSa) qualification work. Key features include 64 KB Flash, 8 KB SRAM, a 48 MHz Cortex-M0+ core, integrated LIN 2.x/SAE J2602 transceiver with up to 20 kbaud bus communication, integrated 5V/3.3V selectable VREG, AEC-Q100 Grade 1 qualification for -40C to +125C operation, Functional Safety documentation, and a 32-pin VQFN package that exposes GPIO, LIN bus, VBAT, VCC, and ground pins. The SiP also integrates ESD protection on LIN, and a low-power standby mode for ECU sleep/wake-up scenarios. Typical applications include automotive body electronics LIN nodes such as window lift, seat control, mirror adjust, ambient lighting, HVAC flaps, and rain/light sensors. The integrated LIN SBC function makes it ideal as a satellite ECU connected directly to the vehicle's LIN bus, replacing discrete MCU + LIN PHY + LDO designs. The SAM HA1E16A AEC-Q100 qualification also simplifies PPAP and ISO 26262 documentation for OEM platforms. When designing with this SiP, treat the LIN bus pinout (LIN, VBAT, VCC) as a matched impedance link and keep the LIN trace short with a strong ground pour to meet automotive EMC requirements. Use the internal VREG output to power the MCU die and external low-current circuitry; for higher-current external loads, add a separate post-regulator. The exposed pad of the VQFN-32 must be soldered to a sufficiently large copper island to dissipate the LIN bus fault-mode heat. This page synthesizes distributor pricing, same-family alternatives, and automotive LIN design notes not found in the manufacturer datasheet introduction.

見積もり お問い合わせ
ATSAMHA1E16A-MBT-BVAO - 64KB LIN SiP MCU Cortex-M0+ | Microchip
ATSAMHA1E16A-MBT-BVAO

ATSAMHA1E16A-MBT-BVAO - 64KB LIN SiP MCU Cortex-M0+ | Microchip

The Microchip Technology ATSAMHA1E16A-MBT-BVAO is a low-power automotive System-in-Package (SiP) device integrating an ARM Cortex-M0+ microcontroller core with an on-board LIN transceiver and voltage regulator. It runs at up to 48 MHz, delivers 2.46 CoreMark/MHz, and ships in a 32-pin VQFN (5x5 mm) package with an exposed thermal pad. A LIN System-in-Package combines a microcontroller core, a physical-layer LIN transceiver, and an integrated voltage regulator on a single substrate. This integration reduces external BOM count, simplifies PCB layout, and is purpose-built for in-vehicle networks where a node must communicate over a single-wire LIN bus while remaining powered from the vehicle's 12 V bus. Within the broader hierarchy, an SiP belongs to the microcontroller family, which itself sits inside the broader power-managed automotive embedded IC category. The device features 64 KB of Flash, 2 KB of read-while-write data Flash, 8 KB of SRAM, and runs from a single 3.3 V supply. AEC-Q100 qualification supports automotive deployment, and the functional-safety (FuSa) architecture targets ISO 26262-capable body and chassis applications. The integrated LIN 2.x transceiver plus on-chip LDO removes the need for an external PHY, while the Cortex-M0+ core ensures deterministic real-time response. Typical applications include LIN slave nodes such as body control modules, seat controllers, mirror adjusters, HVAC damper drivers, RKE receivers, ambient lighting drivers, and small sensor clusters. The Cortex-M0+ core's 2.46 CoreMark/MHz provides ample headroom for low-rate sensor conditioning and LIN message handling. Compared to a discrete MCU plus external LIN transceiver design, the SiP approach typically cuts board area by 30-50% and lowers standby current by eliminating redundant bias chains. When designing with this part, route the LIN bus pin directly to the connector with a minimum 2 kV ESD protection network if the bus is exposed. Place the SiP's exposed pad on a continuous ground copper pour with at least 16 thermal vias to keep junction temperature within the -40C to +105C automotive Grade-1 range. The integrated LIN transceiver handles bus dominant/recessive state transitions, so the firmware stack only needs to manage the UART-to-LIN framing. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical PCB layout guidance not aggregated on the manufacturer datasheet, giving automotive hardware engineers a single source for selection and supply-chain decisions.

見積もり お問い合わせ
ATSAMHA1G14A-MBT - LIN SiP MCU Cortex-M0+ 48MHz 16KB | Microchip
ATSAMHA1G14A-MBT

ATSAMHA1G14A-MBT - LIN SiP MCU Cortex-M0+ 48MHz 16KB | Microchip

The Microchip ATSAMHA1G14A-MBT is a low-power automotive System-in-Package (SiP) integrating an ARM Cortex-M0+ microcontroller, a LIN transceiver, and a voltage regulator in a single 48-pin VQFN (7x7 mm) package. The MCU core runs at up to 48 MHz with 16 KB of Flash, 4 KB of SRAM, and 0.5 KB of read-while-write data Flash. The integrated LIN SBC (System Basis Chip) blocks eliminate the need for an external LIN transceiver and LDO, reducing BOM count for body electronics modules. A System-in-Package (SiP) combines multiple silicon dies in one package to deliver a complete functional subsystem. In the SAM HA1 family, the SiP pairs an automotive-grade Cortex-M0+ MCU die with a LIN 2.x/SAE J2602 transceiver die and a 3.3V/5V linear regulator, enabling single-chip LIN nodes for body and chassis ECUs. This approach sits within the broader hierarchy of integrated circuits -> microcontrollers -> automotive MCUs -> LIN-capable SBC-MCU combinations. Key features include 48 MHz maximum CPU clock, hardware LIN 2.x/SAE J2602 transceiver compliance, integrated 3.3V/5V VREG, AEC-Q100 automotive qualification, 0.5 KB RWW data Flash for EEPROM emulation, and 4 KB SRAM. The device supports 48 GPIO and offers peripheral touch (PTC) plus multiple SERCOM, ADC, and timer channels. Low-power Sleep and Idle modes with fast wake-up make it ideal for always-on automotive body networks where quiescent current is critical. The SiP architecture is built around a 32-bit Cortex-M0+ core with single-cycle I/O access, supporting the Thumb-2 instruction set for compact code density. The LIN SBC die integrates physical layer transceiver, watchdog, and voltage regulator, while the MCU die provides digital control loops, diagnostics, and communication protocol stack (typically LIN LDF-driven). Together they meet ISO 17987 LIN physical layer and ISO 26262 functional safety (FuSa) targets when used with appropriate firmware. Typical applications include automotive body control modules, HVAC switch panels, seat control ECUs, door/window lift modules, steering column switches, and LIN slave nodes in interior lighting. The AEC-Q100 qualification and integrated LIN make it purpose-built for OEMs consolidating wiring harness content into compact LIN nodes. When designing with the ATSAMHA1G14A-MBT, ensure the LIN bus pull-up and master/slave termination are configured per SAE J2602. The wide 5V to 27V (40V transient) battery operation handled by the SBC die, combined with the MCU's low-power modes, allows direct connection to the 12V automotive battery rail without additional protection circuitry for typical body electronics. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, supporting component selection engineers evaluating LIN node MCU choices.

見積もり お問い合わせ
ATSAMHA1G14A-MBT-BVAO - Automotive LIN SiP MCU 32KB Flash | Microchip
ATSAMHA1G14A-MBT-BVAO

ATSAMHA1G14A-MBT-BVAO - Automotive LIN SiP MCU 32KB Flash | Microchip

The Microchip Technology ATSAMHA1G14A-MBT-BVAO is an automotive-grade LIN System-in-Package (SiP) integrating a 32-bit Arm Cortex-M0+ MCU with a LIN transceiver and a voltage regulator in a single 48-pin VQFN (7x7 mm) package. It operates at a CPU clock speed of 48 MHz and is built around the SAM HA1 family, which is AEC-Q100 qualified for automotive body electronics applications. The device includes 16 KB of Flash, 0.5 KB of read-while-write data Flash, and 4 KB of SRAM, with Functional Safety (FuSa) support. A System-in-Package (SiP) is a single component that integrates multiple bare dies into one molded package, allowing the combined silicon to behave like one IC. In the ATSAMHA1G14A-MBT-BVAO the MCU die, LIN SBC (System Basis Chip) die, and LDO die are co-packaged, saving PCB area and BOM cost versus a discrete MCU plus external LIN transceiver design. The SAM HA1 family sits within the broader Automotive MCU hierarchy: Cortex-M0+ -> SAM family -> SAM HA1 sub-family -> automotive body-comfort SiPs. Key features of this part include a -40C to +105C (or +125C) operating temperature range, integrated LIN 2.x/SAE J2602 transceiver, integrated 5V or 3.3V LDO, up to 48 MHz Cortex-M0+ core, and 16 KB Flash. The exposed-pad VQFN-48 (7x7 mm) package provides a low thermal resistance path, essential for automotive under-hood and body-control environments. FuSa documentation supports ISO 26262 system-level integration. Architecturally the device couples the Cortex-M0+ core's Thumb-2 instruction efficiency with a peripheral set that includes timers, ADC, I2C, SPI, USART, and a LIN-capable UART. The integrated LIN SBC handles bus dominant/recessive state decoding, slope control, and thermal shutdown, reducing firmware load. Typical applications include automotive body control modules, HVAC control panels, seat-control switches, mirror adjusters, lighting nodes (LIN-driven), and wiper/door modules. The wide operating range also suits industrial sensor nodes and HVAC fan controllers. When designing with this SiP, follow Microchip's LIN SBC layout guidelines: keep the LIN bus trace short, place a reverse-polarity and TVS protection diode near the bus pin, and provide a stable VBAT input with bulk decoupling of at least 10 uF plus 100 nF close to the VLIN pin.

見積もり お問い合わせ
ATSAMHA1G17A-MZT-BVAO - LIN SiP MCU+Cortex-M0+ 128KB | Microchip
ATSAMHA1G17A-MZT-BVAO

ATSAMHA1G17A-MZT-BVAO - LIN SiP MCU+Cortex-M0+ 128KB | Microchip

The Microchip ATSAMHA1G17A-MZT-BVAO is an AEC-Q100 qualified automotive LIN System-in-Package (SiP) integrating a 32-bit Arm Cortex-M0+ microcontroller, a LIN 2.x/SAE J2602 transceiver, and a 5V LDO voltage regulator into a single 48-pin VQFN (7x7 mm) package. It operates at a maximum clock speed of 48 MHz, achieving 2.46 CoreMark/MHz, and provides 128 KB of Flash, 4 KB of read-while-write data Flash, and 16 KB of SRAM. The 'MZT' ordering code denotes the 48-VQFN EP package shipped in tape-and-reel with the automotive-grade V temperature range (-40C to +125C). A LIN System-in-Package (SiP) is a multi-die module that combines an MCU core, a LIN physical-layer transceiver, and a power-management LDO in a single footprint, eliminating the need for designers to source, qualify, and lay out three separate ICs. The LIN bus standard (ISO 17987 / SAE J2602) is the dominant low-cost in-vehicle networking protocol for non-safety body-electronics sub-networks such as mirror modules, seat controllers, HVAC flaps, ambient lighting, and door-handle sensors. Integrating the transceiver on-die drastically reduces BOM count, PCB area, and EMC risk. Key features of the ATSAMHA1G17A-MZT-BVAO include an integrated LIN 2.x transceiver compliant with SAE J2602-2, an integrated 5V/3.3V LDO supporting direct 12V battery operation, 128 KB Flash / 16 KB SRAM memory, and an operating temperature range of -40C to +125C qualified to AEC-Q100 Grade 1. The 48-VQFN EP package with exposed pad provides a low thermal resistance path and a compact 7x7 mm footprint suitable for space-constrained automotive ECUs. The device targets LIN slave-node body-electronics applications where PCB area and BOM cost dominate the design budget. Typical end products include automotive mirror modules, seat-control units, HVAC flap actuators, ambient-lighting drivers, door-handle sensors, and sunroof controllers. The integrated LIN transceiver handles bus dominant/recessive state transitions with hardware-controlled slew-rate limiting, offloading protocol timing from the Cortex-M0+ core. When designing with the ATSAMHA1G17A-MZT-BVAO, the integrated 5V LDO is powered directly from the 12V vehicle battery (with external reverse-battery and load-dump protection), and the on-die LIN transceiver connects to the bus through a series resistor and an ESD diode. The exposed pad must be soldered to a sufficient copper pour to meet the AEC-Q100 Grade 1 thermal requirements. This page synthesizes AEC-Q100 qualification status, real distributor pricing, drop-in alternatives within the SAM HA1 family, and automotive-grade design notes not consolidated on the manufacturer datasheet cover page.

見積もり お問い合わせ
ATSAML10D14A-MF - 32MHz Cortex-M23 MCU 16KB Flash | Microchip
ATSAML10D14A-MF

ATSAML10D14A-MF - 32MHz Cortex-M23 MCU 16KB Flash | Microchip

The Microchip Technology ATSAML10D14A-MF is an ultra-low-power 32-bit ARM Cortex-M23 microcontroller from the SAM L10 family, featuring 16KB Flash and 4KB SRAM in a 24-pin VQFN (4x4 mm) package. It operates at up to 32 MHz, consumes less than 25 uA/MHz in active mode, and draws less than 100 nA in sleep mode, making it one of the industry's lowest-power Cortex-M23 MCUs. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (SRAM), and integrated peripherals. Within the broader taxonomy, the ATSAML10D14A-MF sits in the ultra-low-power MCU category, which targets battery-operated and energy-harvesting applications. ARM Cortex-M23 cores specifically use the Armv8-M architecture with TrustZone-M security extensions (note: TrustZone is enabled on the SAM L11 family, while the SAM L10 omits TrustZone for lower cost and power). The SAM L10/L11 families represent Microchip's lowest-power general-purpose 32-bit MCU platform. Key features include an enhanced Peripheral Touch Controller (PTC) supporting hardware-based capacitive touch sensing, advanced analog peripherals (12-bit ADC, 10-bit DAC, operational amplifiers, and analog comparators), SERCOM serial communication interfaces, and an ISO7816 smart card interface. The 24-VQFN package offers a compact 4x4 mm footprint suitable for space-constrained PCB designs. Architecturally, the device uses a single-cycle hardware multiplier, MPU for memory protection, and Microchip's proprietary picoPower technology that enables deep-sleep retention modes with sub-microamp standby current. Security features include CRC, true random number generator, and secure boot (without TrustZone). Typical applications include IoT sensor nodes, wearable health monitors, smart home devices, battery-powered industrial sensors, secure access control (without TrustZone), and touch-based human-machine interfaces. The combination of low power, integrated touch, and analog peripherals makes it particularly suited for always-on edge devices. When designing with this part, ensure your PCB layout provides adequate thermal dissipation even though the device is low-power. Use the SERCOM modules (each reconfigurable for I2C/SPI/UART) to maximize pin utilization. Decoupling capacitors (100 nF + 1 uF) should be placed within 3 mm of the VDD pins. This page synthesizes distributor pricing, same-family variants, and practical design notes that complement the manufacturer datasheet for accelerated component selection.

見積もり お問い合わせ
ATSAML10D14A-MU - 32MHz Cortex-M23 MCU, 16KB Flash | Microchip
ATSAML10D14A-MU

ATSAML10D14A-MU - 32MHz Cortex-M23 MCU, 16KB Flash | Microchip

The Microchip Technology ATSAML10D14A-MU is an ultra-low-power 32-bit ARM Cortex-M23 microcontroller from the SAM L10 family, featuring 16KB Flash, 4KB SRAM, and a 32MHz CPU in a 24-pin VQFN (4x4 mm) package. It is engineered for the lowest power consumption in any Cortex-M23 MCU, drawing less than 25 uA/MHz in active mode and under 100 nA in sleep mode. The device supports 1.62V to 3.63V supply operation and includes enhanced peripheral touch (PTC) controller, 12-bit ADC, comparators, and ISO7816 smart card interface for security-sensitive applications. A microcontroller (MCU) is an integrated circuit containing a processor core, program memory, data RAM, and programmable peripherals on a single chip. The ATSAML10D14A-MU belongs to the Cortex-M23 family, the smallest and most energy-efficient implementation of the Armv8-M architecture with TrustZone-ready extensions. In the broader hierarchy it sits within low-power MCUs -> 32-bit microcontrollers -> embedded processors -> semiconductors, designed specifically for battery-powered edge devices and IoT endpoints where nanoamp quiescent current matters. Key features include 16KB Flash with ECC, 4KB SRAM, 12-channel 12-bit 1 MSPS ADC, two analog comparators with window mode, a 32kHz RTC, multiple low-power sleep modes, and a flexible Event System for inter-peripheral signaling without CPU intervention. The integrated Peripheral Touch Controller (PTC) supports hardware-driven capacitive touch sensing with up to 256 channels. The device also features a 16-bit Sigma-Delta DAC and PTC-driven hardware wake-on-touch from deep-sleep. Architecturally, the SAM L10 uses a Cortex-M23 core with single-cycle I/O port access, NVIC with 4 priority levels, and Microchip's proprietary picoPower technology. The bus matrix connects Flash, SRAM, and AHB/APB peripherals through a tightly-coupled low-leakage memory subsystem, allowing sleep currents to drop to under 100 nA with full RAM retention and RTC running. Typical applications include wearable fitness bands, smart sensors, security tokens, smart card readers, IoT endpoints, capacitive touch human-machine interfaces (HMIs), battery-powered medical monitors, and home automation sensor nodes. The 24-VQFN package suits miniaturized PCB layouts common in coin-cell-powered products. When designing with this part, consider the mandatory 1.62V minimum supply for Flash operations and select the appropriate low-power mode to balance wake-up latency against current budget. The PTC peripheral requires careful PCB layout guidelines; refer to the Atmel/Microchip touch design package for sensor routing recommendations. This page consolidates distributor pricing, drop-in compatible SAM L10 family members, and PCB-level design notes not covered in the manufacturer datasheet to accelerate part selection and PCB bring-up.

見積もり お問い合わせ
ATSAML10D14A-MUT - 32MHz Cortex-M23 MCU 16KB Flash | Microchip
ATSAML10D14A-MUT

ATSAML10D14A-MUT - 32MHz Cortex-M23 MCU 16KB Flash | Microchip

The Microchip Technology ATSAML10D14A-MUT is an ultra-low-power 32-bit ARM Cortex-M23 microcontroller from the SAM L10 family, featuring 16KB of Flash memory and 4KB of SRAM in a 24-pin VQFN (4x4 mm) package. It operates at up to 32 MHz, consumes less than 25 uA/MHz in active mode, and drops below 100 nA in sleep mode, making it one of the industry's lowest-power Cortex-M23 MCUs. What is a low-power microcontroller? A low-power microcontroller (MCU) is an integrated circuit that combines a CPU core, memory, and peripherals while consuming the minimum energy required to perform its tasks. It typically falls under the broader categories of embedded controller -> microcontroller -> semiconductor IC, and is essential for battery-operated, energy-harvesting, and always-on IoT devices where quiescent current and sleep-mode efficiency directly determine battery life. Key features of the ATSAML10D14A-MUT include an enhanced Peripheral Touch Controller (PTC) for capacitive touch sensing, a 12-bit analog-to-digital converter (ADC), a 10-bit digital-to-analog converter (DAC), operational amplifiers, and multiple SERCOM serial communication interfaces. It also integrates an ISO7816 smart card interface, event system for peripheral interconnections without CPU intervention, and robust security features including secure boot and cryptographic accelerators. The device operates from a 1.62V to 3.63V supply. The SAM L10 architecture uses the ARM Cortex-M23 core with TrustZone-ready hardware isolation (note: TrustZone is available on the SAM L11 sibling family, not the L10). The chip's sleep current under 100 nA and active efficiency below 25 uA/MHz make it ideal for always-on sensor hubs, wearable health monitors, and remote IoT endpoints that may spend most of their lifecycle in deep sleep. The integrated PTC supports moisture-tolerant touch buttons and sliders with minimal CPU overhead. Typical applications include smart home sensor nodes, wearable fitness bands, electronic shelf labels, battery-powered medical sensors, smart card readers, and industrial IoT endpoints. Its PTC and low-power ADC enable always-on touch interfaces that wake the system only on user interaction. When designing with this device, prioritize sleep-mode current optimization and PTC scan scheduling to maximize battery life. Use the integrated op-amps for signal conditioning before the ADC to reduce BOM cost and PCB area. This page synthesizes distributor pricing, drop-in same-family SAM L10 alternatives, and practical low-power design notes not consolidated on the manufacturer product page.

見積もり お問い合わせ
ATSAML10D15A-MF - 32KB Flash Cortex-M23 MCU | Microchip
ATSAML10D15A-MF

ATSAML10D15A-MF - 32KB Flash Cortex-M23 MCU | Microchip

The Microchip Technology ATSAML10D15A-MF is an ultra-low-power 32-bit ARM Cortex-M23 microcontroller in the SAM L10 family, featuring 32KB Flash, 8KB SRAM, and a 32MHz CPU clock, housed in a 24-pin VQFN (4x4 mm) package. According to Microchip's product page, the device consumes less than 25 uA/MHz in active mode and less than 100 nA in sleep mode, establishing it as one of the lowest-power Cortex-M23 MCUs on the market for battery-sensitive edge nodes. A microcontroller (MCU) is an integrated circuit that combines a processor core, program memory (Flash), data memory (SRAM), and a rich set of on-chip peripherals into a single chip. The Cortex-M23 core represents ARM's smallest and most energy-efficient implementation of the Armv8-M architecture, sitting at the bottom of the Cortex-M hierarchy (Cortex-M23 -> Cortex-M0+ -> Cortex-M3 -> Cortex-M4 -> Cortex-M7). Microcontrollers belong to the broader category of embedded processors and are a sub-category of integrated circuits used for real-time control and sensing tasks. Key features of the ATSAML10D15A-MF include an enhanced peripheral touch controller for capacitive sensing without external components, a 12-bit ADC, multiple SERCOM channels configurable as I2C/SPI/UART, an ISO7816 smart card interface, an Event System for CPU-independent peripheral interconnect, and a 125°C maximum junction temperature for industrial-grade operation. TrustZone-M security is NOT included (that feature belongs to the SAM L11 family). The ATSAML10D15A-MF integrates Microchip's proprietary picoPower technology and an on-chip buck converter that keeps the core logic supplied efficiently across a 1.62V to 3.63V VDD range. The 24-VQFN (4x4 mm) package is one of the smallest variants in the SAM L10 lineup and includes an exposed pad for thermal dissipation. Typical applications include IoT sensor nodes, wearable health monitors, smart-home battery devices, capacitive touch human-machine interfaces (HMIs), secure access peripherals, and low-power wireless sensor endpoints. The 100 nA sleep current extends battery life beyond 10 years when paired with a CR2032 cell and a properly duty-cycled radio. Designers should pair the ATSAML10D15A-MF with a 100 nF decoupling capacitor on each VDD pin plus a 4.7 uF bulk capacitor on the main supply, and connect the exposed pad to a continuous ground plane for thermal performance. The brown-out detector (BOD) and watchdog timer (WDT) should always be enabled in production firmware. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, giving engineers a single reference for evaluation, sourcing, and BOM optimization.

見積もり お問い合わせ
ATSAML10D15A-MUT - 32KB Flash Cortex-M23 MCU | Microchip 24-VQFN
ATSAML10D15A-MUT

ATSAML10D15A-MUT - 32KB Flash Cortex-M23 MCU | Microchip 24-VQFN

The Microchip Technology ATSAML10D15A-MUT is an ARM Cortex-M23 SAM L10 microcontroller delivering 32-bit performance at 32 MHz with 32 KB of Flash and 8 KB of SRAM, housed in a 24-pin VQFN (4x4 mm) package rated for the +85 C industrial temperature grade. It is the industry-leading ultra-low-power MCU in the SAM L10 family, consuming less than 25 uA/MHz in active mode and less than 100 nA in sleep mode. A microcontroller (MCU) is a single-chip processor that integrates a CPU core, volatile memory (SRAM), non-volatile program memory (Flash), and programmable peripherals into one package. The Cortex-M23 is the smallest and most energy-efficient ARMv8-M baseline processor, sitting below Cortex-M0+/M4 in the ARM Cortex-M family hierarchy (Cortex-M23 -> Cortex-M0 -> Cortex-M microcontroller -> embedded processor). SAM L10 extends that baseline with Microchip's proprietary peripherals such as the Peripheral Touch Controller (PTC) and TrustZone-M security. Key features of the ATSAML10D15A-MUT include the 32 KB Flash program memory, 8 KB SRAM, a Peripheral Touch Controller for capacitive sensing, a 12-bit ADC and DAC, multiple SERCOM serial interfaces, an ISO7816 smart-card interface, and the Event System for low-latency inter-peripheral signalling. The wide 1.62-3.63 V supply range and integrated op-amp further reduce external component count. Architecturally the device uses an ARMv8-M baseline core with single-cycle I/O access via the AHB-APB bridge, a low-power Always-On (AON) domain for RTC and counter, and a brown-out detector tied to the Power Manager. The Cortex-M23 also brings TrustZone-M hardware isolation for secure firmware partitions - rarely seen at this flash tier. Typical applications include battery-powered IoT sensors, secure smart-card terminals, capacitive-touch user interfaces, low-power wearables, and home/building automation nodes where sleep-mode current dominates battery life. Designers should budget decoupling (one 100 nF plus one 1 uF ceramic per VDD pin), verify the 24-VQFN thermal pad is soldered to a continuous ground pour for thermal/electrical performance, and confirm the chosen toolchain (MPLAB X IDE / XC32 / Microchip Studio + Keil / IAR) supports TrustZone-M if used. This page consolidates distributor pricing, verified drop-in alternatives, and practical design notes that complement (not duplicate) the manufacturer datasheet.

見積もり お問い合わせ
ATSAML10D15A-YF - SAM L10 32KB Flash Cortex-M23 MCU | Microchip
ATSAML10D15A-YF

ATSAML10D15A-YF - SAM L10 32KB Flash Cortex-M23 MCU | Microchip

The Microchip Technology ATSAML10D15A-YF is a 32-bit ARM Cortex-M23 microcontroller from the SAM L10 family, delivering 32KB of Flash memory, 8KB of SRAM, and a 32MHz maximum CPU clock in a 24-pin SSOP package. It targets ultra-low-power embedded applications, consuming less than 25 uA/MHz in active mode and less than 100 nA in sleep mode. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable peripherals. The Cortex-M23 core is an Armv8-M Baseline architecture designed for energy-efficient deterministic embedded computing, sitting within the broader hierarchy of Cortex-M microcontrollers -> 32-bit MCUs -> microcontrollers -> embedded ICs. The SAM L10 family is purpose-built for battery-powered IoT endpoints where deep-sleep current and active-mode efficiency directly determine battery life. Key features of the ATSAML10D15A-YF include a 32KB Flash program memory (32K x 8), 8KB SRAM, an enhanced Peripheral Touch Controller (PTC), multiple SERCOM serial communication interfaces, a 12-bit ADC, a 10-bit DAC, an operational amplifier, and an analog comparator. The device operates from 1.62V to 3.63V supply and integrates an ISO7816 smart card interface and Event System for inter-peripheral signalling without CPU intervention. At the architecture level, the device leverages the Cortex-M23's single-cycle IO port, hardware single-cycle multiplier, and TrustZone-M for optional secure firmware partitioning. The integrated PTC supports capacitive touch sensing with driven shield and moisture rejection, eliminating external touch ICs in user-interface designs. Typical applications include battery-powered IoT sensor nodes, wearable health monitors, secure smart-card readers, capacitive touch user interfaces, and home automation endpoints. The 24-pin SSOP package supports compact through-hole-style PCB layouts where 0.65mm pitch QFN footprints are undesirable for hand-rework or low-density boards. When designing, prioritise low quiescent current paths - disable unused SERCOM blocks, use sleep walking instead of polling, and confirm the PTC scan rate matches your touch response target. A 100nF decoupling cap must be placed within 5mm of the VDD pin to meet the datasheet noise specification. This page combines distributor pricing, same-family drop-in alternatives, and practical low-power design notes into a single reference not found in the standalone datasheet.

見積もり お問い合わせ
ATSAML10D15A-YFT - 32KB Flash ARM Cortex-M23 MCU 32MHz
ATSAML10D15A-YFT

ATSAML10D15A-YFT - 32KB Flash ARM Cortex-M23 MCU 32MHz

The Microchip Technology ATSAML10D15A-YFT is an ultra-low-power 32-bit ARM Cortex-M23 microcontroller from the SAM L10 family, integrating 32KB of Flash, 8KB of SRAM, and running at up to 32 MHz. Housed in a 24-pin SSOP package, it is engineered for always-on, energy-harvesting, and battery-powered applications, with active mode current under 25 uA/MHz and sleep mode current below 100 nA. An ARM Cortex-M23 MCU is a 32-bit microcontroller core built on the ARMv8-M Baseline architecture that combines Thumb-2 instruction efficiency with optional TrustZone-M security extensions. Microcontrollers (MCUs) sit at the heart of embedded systems, providing CPU, memory, and peripherals on a single die; the SAM L10 family specifically targets low-power IoT nodes where every microamp of quiescent current translates directly into battery life. Key features include an enhanced peripheral touch controller (PTC) for capacitive sensing, a 12-bit ADC, a 10-bit DAC, an operational amplifier, analog comparators (AC), multiple SERCOM serial interfaces, ISO7816 smart card interface, and an event system for hardware-triggered inter-peripheral signaling without CPU intervention. The integrated Peripheral Touch Controller supports capacitive buttons, sliders, and proximity sensors without external components. Architecturally, the device uses a Cortex-M23 core with single-cycle I/O access, a flexible SERCOM block that can be configured as UART, SPI, I2C, or LIN, and a low-power RTC with calendar and alarm functions. The 32KB Flash is organized as 32K x 8 with ECC protection, and the 8KB SRAM is retained across sleep modes. The Cortex-M23 implements the ARMv8-M Baseline instruction set, bringing modern tooling and code density advantages to the Microchip low-power portfolio. Typical applications include IoT sensor nodes, wearable health and fitness devices, smart-home control panels with touch input, battery-powered remotes, industrial sensors with HMI, ISO7816 smart card readers, and energy-harvesting wireless endpoints using LoRa, BLE, or sub-GHz transceivers. The 24-SSOP package enables compact PCB designs while remaining hand-solderable for prototyping. When designing with this device, place a 100 nF decoupling capacitor as close as possible to the VDD pin and add a bulk capacitor of at least 1 uF on the main supply rail. Connect unused I/O pins to a defined logic level (VCC or GND) to minimize shoot-through current during deep-sleep cycles. The Cortex-M23 supports Sleep, Deep-Sleep, and Standby modes selectable via the Power Manager, allowing per-application optimization of wake-up latency versus current consumption. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, helping sourcing engineers and firmware developers evaluate the ATSAML10D15A-YFT for next-generation low-power designs as of 2026-09-22.

見積もり お問い合わせ
ATSAML10D15A-YUT - 32KB Flash Cortex-M23 MCU | Microchip
ATSAML10D15A-YUT

ATSAML10D15A-YUT - 32KB Flash Cortex-M23 MCU | Microchip

The Microchip Technology ATSAML10D15A-YUT is an ARM Cortex-M23 based 32-bit microcontroller from the SAM L10 family, featuring 32 KB of Flash, 8 KB of SRAM, and a maximum CPU clock of 32 MHz, packaged in a 24-pin SSOP (0.209" / 5.30 mm width). What is a low-power Cortex-M23 microcontroller? A 32-bit microcontroller is an integrated circuit that combines a CPU core, program memory (Flash), data memory (SRAM), and a set of peripherals on a single die. The Cortex-M23 is Arm's smallest and most energy-efficient TrustZone-capable core, sitting below Cortex-M0+ and Cortex-M3 in the hierarchy: ARM core -> Cortex-M family -> Cortex-M23 -> SAM L10/L11 MCU -> 32-bit low-power microcontroller. The SAM L10 family specifically targets battery-powered applications that need deterministic performance with deep-sleep current below 100 nA. Key features include less than 25 uA/MHz active mode power consumption, less than 100 nA sleep mode current, an enhanced peripheral touch controller (PTC), multiple SERCOM serial interfaces, a 12-bit ADC, 10-bit DAC, on-chip op-amp, and analog comparators. The integrated ISO7816 smart card interface and event system make it suitable for secure and event-driven designs without CPU wake-ups. The device is built on a low-leakage process and integrates Arm TrustZone for Cortex-M23, allowing secure and non-secure firmware regions. The peripheral touch controller supports capacitive buttons, sliders, and proximity sensing in noisy environments, while the 12-bit ADC and 10-bit DAC provide sufficient resolution for sensor conditioning and small-signal generation tasks. Typical applications include IoT sensor nodes, secure wearables, smart card terminals, capacitive touch user interfaces, and battery-powered industrial edge devices. The combination of sub-100 nA sleep current and TrustZone security makes the SAM L10 particularly attractive for always-on sensor endpoints. When designing with this part, choose the L10 over the L11 only if you do not need the L11's additional crypto accelerators and larger SRAM; both share the same Cortex-M23 core. The 24-SSOP package is footprint-compatible with other SAM L10/L11 24-pin variants. This page synthesizes distributor pricing, drop-in 24-SSOP alternatives, and design notes not consolidated on the Microchip datasheet. Sourced from DigiKey, Mouser, and the Microchip product page as of 2026-09-22.

見積もり お問い合わせ
ATSAML10D16A-MFT - 32MHz Cortex-M23 MCU 64KB Flash | Microchip
ATSAML10D16A-MFT

ATSAML10D16A-MFT - 32MHz Cortex-M23 MCU 64KB Flash | Microchip

The Microchip Technology ATSAML10D16A-MFT is a 32-bit ARM Cortex-M23 microcontroller running at 32 MHz with 64 KB of Flash and 16 KB of SRAM, packaged in a 24-pin VQFN (4x4 mm) with exposed thermal pad. The SAM L10 family is engineered as the industry's lowest-power Cortex-M23 MCU, drawing less than 25 uA/MHz in active mode and below 100 nA in sleep mode, making it ideal for battery-powered and energy-harvesting designs. What is a low-power microcontroller? An MCU is a single-chip computer integrating a CPU core, memory, and peripherals; a low-power variant adds aggressive clock gating, multiple sleep modes, and SleepWalking peripherals that wake only specific subsystems. Within the taxonomy, ATSAML10D16A-MFT is a 32-bit microcontroller, then a Cortex-M-class MCU, then a sub-1V active-class low-power MCU used as a power-management IC's companion in always-on systems. Key features include an enhanced peripheral touch controller (PTC) for capacitive sensing without external components, a 12-bit ADC with up to 12 channels, an on-chip temperature sensor, and an ISO7816 smart-card interface. The device integrates an event system for inter-peripheral signalling without CPU wake-up and supports serial-wire debug. Security includes a unique 128-bit serial number and Microchip's SAM L10 TrustZone-lite tamper detection. Technical depth: The Cortex-M23 core implements the Armv8-M baseline profile with single-cycle I/O, hardware single-precision multiply, and a 2-stage pipeline. The 24-VQFN exposed pad lowers thermal resistance and enables direct PCB die-attached heat spreading for sustained 32 MHz operation across the -40C to +125C industrial temperature range. Typical applications include IoT sensor nodes, wearable health monitors, smart-card terminals, low-power wireless HMI touch interfaces, battery-powered industrial gauges, and home automation endpoints. The 100 nA sleep current enables multi-year coin-cell life when the application wakes only briefly to sample. Design consideration: At 32 MHz with all peripherals active the active current stays below 25 uA/MHz; designers should bias the PTC clock and ADC prescaler to keep the duty cycle low. Decouple VDD and VDDCORE pins with 100 nF X7R close to each pin. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes that streamline the BOM decision beyond what the manufacturer datasheet alone provides.

見積もり お問い合わせ
ATSAML10D16A-MU - 64KB Flash Cortex-M23 MCU | Microchip
ATSAML10D16A-MU

ATSAML10D16A-MU - 64KB Flash Cortex-M23 MCU | Microchip

The Microchip ATSAML10D16A-MU is a 32-bit ARM Cortex-M23 microcontroller from the SAM L10 family with 64KB of Flash memory and 64KB of code space (64K x 8), housed in a 24-pin VQFN (4x4 mm) package with exposed pad. It runs at a maximum CPU clock of 32 MHz and is positioned by Microchip as the industry's lowest-power Cortex-M23 MCU, consuming less than 25 uA/MHz in active mode and less than 100 nA in sleep mode. Background: A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile working memory (SRAM), and a rich set of peripherals on a single die. ARM Cortex-M23 cores are 32-bit processors designed for embedded applications that need deterministic real-time response, low active power, and very deep sleep current for battery-driven products. The Cortex-M23 sits at the low-power entry point of the ARM Cortex-M family, sitting below Cortex-M0+/M0 and offering an Armv8-M baseline architecture with optional TrustZone-M hardware isolation. Key differentiating features include an enhanced peripheral touch controller (PTC), advanced analog peripherals, an ISO7816 smart-card interface for secure payment and identification applications, a low-latency event system for inter-peripheral signaling without CPU wake-up, and SleepWalking peripherals that wake the system only on matching conditions. The wide 1.62V to 3.63V operating voltage range covers single-cell lithium, coin-cell, and 3.3V regulated rails. The device uses a single-wire SERCOM-configurable peripheral scheme and integrates up to 16KB SRAM plus 8KB backup SRAM for state retention. On-chip analog includes a 12-bit ADC and 10-bit DAC for sensor interfacing. The tiny 4x4 mm 24-VQFN package exposes a thermal pad that must be soldered to a PCB copper pour to keep junction temperature within the -40C to +85C industrial range. Typical applications include smart-card and secure-element readers, battery-powered IoT sensor nodes, low-power wearable health devices, capacitive-touch human-machine interfaces (buttons, sliders, wheels), and ultra-low-power wireless sensor end nodes. The combination of Cortex-M23 processing, sub-100nA sleep, and an integrated touch controller is rarely found in competing parts. Design tip: route the exposed pad (EP) of the VQFN-24 to a continuous GND copper pour with multiple thermal vias to achieve the 38 C/W theta_JA stated in the Microchip datasheet. Skip the EP landing and the junction can climb more than 25C above ambient at modest loads, derating ambient capability. This page synthesizes current distributor stock, drop-in same-package and cross-brand alternatives, and practical low-power design guidance that is not present on a single manufacturer product page.

見積もり お問い合わせ
ATSAML10D16A-MUT - Cortex-M23 MCU 64KB Flash 24-VQFN | Microchip
ATSAML10D16A-MUT

ATSAML10D16A-MUT - Cortex-M23 MCU 64KB Flash 24-VQFN | Microchip

The Microchip Technology ATSAML10D16A-MUT is an ultra-low-power 32-bit ARM Cortex-M23 microcontroller from the SAM L10 family, integrating 64 KB of Flash and 16 KB of SRAM in a 24-pin VQFN (4x4 mm) package. It operates at up to 32 MHz, delivers less than 25 uA/MHz in active mode, and drops to less than 100 nA in sleep mode, making it the industry's lowest-power Cortex-M23 MCU. Peripherals include an enhanced peripheral touch controller (PTC), a 12-bit ADC, analog comparators, an ISO7816 smart-card interface, a SERCOM-based communication subsystem, an Event System, and SleepWalking peripherals that wake individual sub-blocks without waking the CPU. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and programmable I/O peripherals. The SAM L10 sits in the hierarchy: Cortex-M23 -> ARM Cortex-M family -> 32-bit MCU -> embedded microcontroller -> semiconductor. ARM Cortex-M23 specifically adds TrustZone-ready architecture (used by SAM L11) and a deterministic Thumb-2 instruction set, targeting deterministic real-time control at very low energy budgets. Key features of the ATSAML10D16A-MUT include a 12-bit 1 Msps ADC with hardware oversampling to 16-bit resolution, multiple SERCOM channels that can each be configured as UART, SPI, or I2C, a 32 kHz low-power RTC, brown-out detection, and a built-in PTC supporting up to 256 mutual-capacitance touch channels for capacitive user interfaces. The device runs from 1.62 V to 3.63 V supply and supports industrial-grade -40C to +85C ambient temperatures. From an architecture standpoint, the SAM L10 implements a two-layer AHB-Lite bus matrix, single-cycle I/O access, and Microchip's SleepWalking technology that lets peripherals inspect incoming data while the CPU clock is gated. This combination yields the datasheet-claimed sub-25 uA/MHz active figure, validated under CoreMark workloads with all peripherals disabled except retention RAM. Typical applications include battery-powered IoT sensors, wearable health and fitness devices, smart-card and secure-element readers (leveraging the ISO7816 interface), low-power wireless sensor nodes paired with a separate radio SoC, HMI panels built around the PTC touch controller, and home automation endpoints. The 24-VQFN (4x4 mm) footprint keeps the BOM small for compact wearables. When designing with this part, choose LDO or DC-DC regulators whose quiescent current is below the MCU's sleep floor (100 nA) to preserve the energy budget, and follow the SAM L10 PCB layout checklist for decoupling and ground return paths.

見積もり お問い合わせ
ATSAML10D16A-YF - 32MHz Cortex-M23 MCU 64KB Flash | Microchip
ATSAML10D16A-YF

ATSAML10D16A-YF - 32MHz Cortex-M23 MCU 64KB Flash | Microchip

The Microchip Technology ATSAML10D16A-YF is an ultra-low-power 32-bit ARM Cortex-M23 microcontroller from the SAM L10 family, featuring 64KB Flash and 16KB SRAM in a 24-pin SSOP package. It operates at up to 32 MHz with a 1.62V to 3.63V supply range, consuming less than 25 uA/MHz in active mode and less than 100 nA in sleep mode, making it the industry's lowest-power Cortex-M23 MCU. An ARM Cortex-M23 microcontroller is a 32-bit RISC processor core implementing the Armv8-M baseline architecture with TrustZone-M security. It belongs to the broader hierarchy: microcontroller -> embedded MCU -> semiconductor IC -> ARM Cortex-M family. The Cortex-M23 delivers Thumb-2 instruction set efficiency, deterministic interrupt handling, and optional hardware isolation, making it suitable for secure, low-power IoT endpoints. Key features of the ATSAML10D16A-YF include an enhanced peripheral touch controller (PTC) supporting driven-shield and mutual-capacitance modes, a 12-bit ADC with up to 20 channels, multiple SERCOM interfaces configurable as UART/SPI/I2C, an ISO7816 smart card interface, and the SAM L10 SleepWalking peripheral architecture. The device integrates an event system for inter-peripheral signaling without CPU wakeup, achieving deep-sleep current below 100 nA while retaining RTC and RAM state. Technically, the SAM L10 architecture couples the Cortex-M23 core with a low-power bus matrix, dedicated sleep peripherals, and an on-chip voltage regulator with multiple LDOs. The part supports up to 6 SERCOM, 16 PWM channels, a real-time clock with calendar, and a full-speed USB 2.0 device interface on related variants. TrustZone-M enables secure boot and isolated trusted execution. Typical applications include battery-powered IoT sensors, secure smart-card terminals, wearable health monitors, HVAC touch-key pads, and energy-harvesting wireless nodes. The integrated PTC eliminates external touch ASICs, and the SleepWalking peripherals allow event-driven wakeup from deep sleep without continuous CPU polling. When designing, prioritize the SSOP-24 thermal pad layout, route the PTC shield traces with careful guarding, and follow the datasheet SleepWalking configuration sequence to achieve the datasheet's sub-100 nA standby current. TrustZone-M configuration must be locked before deploying production firmware. This page synthesizes distributor pricing, drop-in same-family alternatives (ATSAML10D15A-YFT, ATSAML10D16A-MFT), and practical design guidance not found in the standalone manufacturer datasheet.

見積もり お問い合わせ