Produk (44,000+)

INA2143U - 5-V/µs Dual Precision Difference Amplifier | TI
INA2143U

INA2143U - 5-V/µs Dual Precision Difference Amplifier | TI

The Texas Instruments INA2143U is a dual high-speed precision difference amplifier featuring 5 V/µs slew rate, 250 µV offset, selectable gain settings of 10 or 0.1, and a 14-pin SOIC package. The device is intended for systems that measure small voltage differences and require amplified differential outputs. A difference amplifier is a specialized operational-amplifier circuit that compares voltages applied to its inverting and non-inverting inputs and amplifies the voltage between them. This method helps reject signals that appear equally on both inputs, making difference amplifiers useful within measurement, instrumentation, analog-control, and signal-conditioning systems. The INA2143U belongs to the amplifier IC category and combines two precision difference amplifiers in one package. Key features include a 5 V/µs slew rate, 250 µV offset, gain options of 10 and 0.1, dual-channel operation, and an operating temperature range of -55°C to 125°C. The 5 V/µs slew rate allows the output to respond quickly to input-voltage changes, while the selectable gain provides flexibility for different differential-signal levels. Each channel can support the two stated gain configurations. The INA2143U combines two difference amplifiers in a single 14-pin SOIC (D) package, reducing board area when two differential channels are required. Its high-speed and precision positioning makes it applicable to fast analog signal conditioning, where the main design objective is to preserve the relationship between two input voltages while converting the differential signal into a single-ended output. Typical applications include current-sense amplifier front ends, differential sensor interfaces, bridge-based measurement circuits, industrial instrumentation, and analog control systems. In a current-sense design, the amplifier processes the voltage generated across a sense resistor rather than the full supply voltage. In a bridge or differential sensor interface, it rejects common-mode voltage and preserves the smaller differential component being measured. Designers should use the manufacturer pin-description table when assigning traces and power connections, and they should verify signal amplitudes against the selected gain of 10 or 0.1. PCB placement should minimize resistive and capacitive pickup around the differential inputs, while supply bypassing should follow the connection and capacitor recommendations in the manufacturer datasheet. This page combines the confirmed INA2143U operating characteristics with practical selection guidance, application context, package information, and drop-in replacement validation. It distinguishes confirmed device attributes from parameters that require confirmation from the complete manufacturer datasheet, helping engineers plan sourcing and circuit design with fewer assumption-driven steps.

RFC Hubungi kami
INA217AIP - Low-Noise Instrumentation Amplifier | Texas Instruments
INA217AIP

INA217AIP - Low-Noise Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA217AIP is a low-noise, low-distortion monolithic instrumentation amplifier in an 8-pin PDIP package. It accepts a 4.5 V to 18 V supply, provides a typical gain of 3 V/V, features 250 µV input offset voltage, and supports a slew rate of 15 V/µs with 3.4 MHz bandwidth. An instrumentation amplifier is a specialized amplifier optimized for measuring low-level differential signals. Its internal signal path rejects common-mode noise while amplifying the voltage difference between two inputs. The INA217 belongs to the instrumentation amplifier, differential amplifier, analog amplifier, and signal-conditioning IC hierarchy, making it suitable for precision sensor conditioning, balanced audio, industrial measurement, and medical instrumentation. The device uses current-feedback circuitry to provide wide bandwidth and strong dynamic response over a broad gain range. Its distortion-cancellation architecture is intended to maintain low distortion even at higher gain. The manufacturer identifies near-theoretical noise performance for a 200 Ω source impedance, making balanced low-impedance microphone signals a primary use case. The monolithic implementation also provides differential inputs, low noise, and low distortion in one package. INA217AIP is identified as a replacement for the SSM2017 and is available with the same DIP-8 and wide-body SOL-16 pin arrangements. The DIP-8 format is useful when an existing instrument-amplifier layout must be retained. Its 15 V/µs slew rate supports high-level audio stages, while differential input handling improves rejection of common-mode interference in measurement systems. Typical applications include professional microphone preamplification, low-level bridge or transducer signal conditioning, industrial process measurement, and medical monitoring. In a microphone circuit, the part processes the differential output of a balanced capsule while rejecting much of the shared noise appearing on both signal conductors. Its low-noise, low-distortion characteristics help preserve the signal-to-noise ratio of the source. When designing around INA217AIP, preserve the pin arrangement of the original SSM2017 layout and follow the manufacturer datasheet for gain-setting resistors, supply bypass capacitors, and output drive requirements. Check input common-mode range, output swing, and source impedance at the selected gain because instrumentation amplifiers can become input-voltage-range constrained even when their bandwidth remains adequate. This product page combines the manufacturer electrical description, package information, compatible-device context, and application-level engineering guidance. It also distinguishes direct replacements from alternatives that require different packages, helping designers evaluate PCB reuse, signal bandwidth, and noise performance before committing to a component.

RFC Hubungi kami
INA2181 26V Dual-Channel Current Sense Amp | TI | Gain 20 V/V
INA2181A1IDGSR

INA2181 26V Dual-Channel Current Sense Amp | TI | Gain 20 V/V

The Texas Instruments INA2181 (e.g., INA2181A1IDGSR) is a 26V, dual-channel, bidirectional, 350kHz voltage-output current sense amplifier in a 10-pin VSSOP (DGS) package, part of the cost-optimized INAx181 family. It senses voltage drops across shunt resistors on low- or high-side rails and outputs a ground-referenced analog voltage proportional to load current. A current sense amplifier (also called a current-shunt monitor) is a specialized difference amplifier that extracts a small differential shunt voltage riding on a large common-mode voltage and converts it to a ground-referenced single-ended signal. Within the signal chain hierarchy it sits between the shunt resistor and an ADC or comparator, serving as a front-end element of power management and battery monitoring systems. Key features include a wide 2.7V to 26V common-mode range that is independent of the 2.7V to 5.5V supply, 350kHz bandwidth for fast load-transient monitoring, bidirectional operation with a reference pin for charging/discharging current measurement, and factory-calibrated gain options (A1 = 20 V/V, A2 = 50 V/V, A3 = 100 V/V, A4 = 500 V/V) that eliminate gain-setting resistors. The zero-drift architecture delivers low offset for small shunt voltages. The dual channels share one package, halving board area versus two single-channel monitors such as the INA181. Rail-to-rail output swings close to the supply rails, maximizing ADC dynamic range. All device options are specified from -40C to +125C. Typical applications include battery current monitoring in portable and industrial equipment, DC motor drive phase and bus current sensing, telecom and server power supply current telemetry, and load-current supervision in 12V/24V rails feeding TI C2000 or MSPM0 MCUs. Design tip: keep the shunt voltage in the 10 mV to 100 mV range at full load - large enough to swamp offset error, small enough to limit shunt power dissipation. Route Kelvin sense traces directly to the shunt pads to preserve accuracy.

RFC Hubungi kami
INA2181A3IDGSR - 26V Dual-Channel Current Sense Amp | TI
INA2181A3IDGSR

INA2181A3IDGSR - 26V Dual-Channel Current Sense Amp | TI

The Texas Instruments INA2181A3IDGSR is a 26V, dual-channel, bidirectional voltage-output current sense amplifier with a fixed gain of 100 V/V (A3 version), 350 kHz bandwidth, and a common-mode input range of -0.2 V to +26 V, housed in a 10-pin VSSOP (DGS) package rated from -40C to +125C. A current sense amplifier (also called a current-shunt monitor) is a specialized difference amplifier that senses the small voltage drop across a shunt resistor and converts it into a ground-referenced output signal. Within the power-management IC hierarchy, it sits alongside voltage regulators and battery-management devices as a core building block of power monitoring and protection subsystems. Key features include the wide -0.2 V to +26 V common-mode range that operates independently of the supply voltage, enabling high-side and low-side sensing on 24 V industrial rails. The A3 gain option of 100 V/V with a 2 V/us output slew rate and 350 kHz bandwidth suits fast, medium-sensitivity current monitoring. Offset voltage is tightly specified: a maximum of plus/minus 150 uV at VCM = 0 V and plus/minus 500 uV at VCM = 12 V, according to the TI datasheet. The INAx181 architecture senses bidirectional current with an external reference voltage applied to the REF pin, allowing the output to be offset for positive and negative current indication. Rail-to-rail output swing maximizes ADC dynamic range on low-supply rails, and the cost-optimized design targets volume production. Typical applications include battery charging systems, 24 V industrial power supplies, motor drive DC bus monitoring, and telecom or server power-supply current telemetry where two channels share one shunt scheme or monitor two rails. Design consideration: keep the shunt resistor value and the A3 gain of 100 V/V balanced - a 10 mV full-scale shunt drop yields 1 V output, so size the shunt to use the ADC input range without exceeding the output swing limits. This page synthesizes distributor pricing, drop-in alternatives within the INAx181 family, and practical design notes not found in the manufacturer datasheet.

RFC Hubungi kami
INA2181A4QDGSRQ1 - 26V Dual 350kHz Current Sense Amp AEC-Q100 | TI
INA2181A4QDGSRQ1

INA2181A4QDGSRQ1 - 26V Dual 350kHz Current Sense Amp AEC-Q100 | TI

The Texas Instruments INA2181A4QDGSRQ1 is an AEC-Q100 qualified, 26V, dual-channel, bidirectional current sense amplifier (also called a current-shunt monitor) with a 350 kHz bandwidth and a fixed gain of 200 V/V (A4 gain variant), housed in a 10-pin VSSOP (DGS) package. It senses voltage drops across current-sense resistors at common-mode voltages from -0.2 V to +26 V, independent of its own supply voltage, and provides a rail-to-rail voltage output. A current sense amplifier is a specialized difference amplifier, within the broader hierarchy of instrumentation amplifiers and operational amplifier signal-conditioning ICs, designed to measure the small differential voltage developed across a shunt resistor and convert it into a ground-referenced output voltage proportional to load current. Bidirectional devices like the INA2181 also detect current flowing in both directions, which is essential in battery charging and discharging monitoring. Key features of the INA2181A4QDGSRQ1 include the wide -0.2 V to 26 V common-mode range that survives automotive load-dump-adjacent conditions, dual-channel integration that halves board area versus two single-channel amplifiers, a 350 kHz bandwidth suitable for fast current-loop control, and the cost-optimized INAx181-Q1 family architecture. Technically, the INA2181-Q1 uses a zero-drift-free precision front end with a fixed gain set by internal resistors; the A4 variant provides 200 V/V gain, allowing very small shunt resistances (sub-10 mOhm) to be used, reducing shunt power dissipation at high currents. The voltage output architecture requires no ADC-side gain stage and simplifies interfacing with microcontroller ADC inputs. Typical applications include automotive battery management systems, 48V and 12V automotive power rails, industrial motor drives, telecom -48V systems, and server hot-swap current monitoring. Design-wise, place the shunt resistor close to the amplifier inputs, use Kelvin (4-wire) connections to the sense resistor, and filter differential noise at the inputs. Note that the 200 V/V gain limits full-scale shunt voltage to about 20 mV for a 4 V output swing. This page synthesizes distributor pricing, drop-in same-family gain-variant alternatives, and practical design notes not found in the manufacturer datasheet.

RFC Hubungi kami
INA240A1D - 20V/V Bidirectional Current Sense Amp | TI
INA240A1D

INA240A1D - 20V/V Bidirectional Current Sense Amp | TI

The Texas Instruments INA240A1D is a bidirectional, zero-drift current-sense amplifier with a gain of 20 V/V, a common-mode voltage range of -4 V to 80 V, and an 8-pin SOIC package. It measures the voltage developed across a shunt resistor on either the high side or low side of a power path and produces an analog output proportional to current. A current-sense amplifier is a specialized instrumentation amplifier that converts the small differential voltage across a current shunt into a larger, easier-to-process voltage. The INA240 family belongs to the amplifier hierarchy as a current-sense amplifier, instrumentation amplifier, analog IC, and semiconductor. Its common-mode range allows the shunt to remain near a supply rail while high voltage, high current, or both are present in the monitored circuit. The INA240A1D combines a 20 V/V gain setting with bidirectional operation and enhanced PWM rejection. Zero-drift architecture minimizes output drift as temperature changes, while the -4 V to 80 V common-mode range supports demanding industrial power systems. Its analog output can be centered near ground for bidirectional current measurement by applying the appropriate reference configuration. The device also supports unidirectional sensing when both reference pins are tied to ground. Internally, the device provides precision differential sensing, a low-offset amplifier, and an analog output stage. Because the common-mode input range is independent of the supply voltage in the relevant operating region, the INA240 can sense voltage drops across a high-side shunt without requiring the amplifier supply to exceed the sensed bus voltage. This architecture is particularly useful when PWM switching nodes create large common-mode transients. Typical applications include motor-control systems, industrial power supplies, robotics, solar inverters, battery packs, solenoid drivers, LED drivers, and protected DC power rails. The INA240A1D is especially appropriate when current must be measured bidirectionally, the shunt may sit above ground, and PWM rejection is important. A 20 V/V gain also reduces the required shunt resistance when the measured current range is relatively low. When designing the circuit, verify that the shunt power dissipation remains below its rating and that the amplifier output stays within its valid output range at maximum load current. Place the differential input traces directly across the shunt, keep them short and symmetric, and provide stable supply decoupling close to the device. Do not exceed the absolute maximum ratings for supply voltage, common-mode voltage, or input voltage. This page combines manufacturer specifications, drop-in alternatives, application guidance, and practical design notes for engineers evaluating the INA240A1D in motor, industrial, and high-side current-measurement systems.

RFC Hubungi kami
INA240A1PW - 80V Bidirectional Current Sense Amp | TI TSSOP-8 (Tape & Reel)
INA240A1PW

INA240A1PW - 80V Bidirectional Current Sense Amp | TI TSSOP-8 (Tape & Reel)

The Texas Instruments INA240A1PW is a -4 V to 80 V bidirectional, ultra-precise current-sense amplifier with enhanced PWM rejection, housed in an 8-pin TSSOP (PW) package with a fixed gain of 20 V/V. It senses drops across shunt resistors over a wide common-mode range independent of supply voltage and integrates a zero-drift chopper architecture that keeps input offset below 25 uV and offset drift below 100 nV/°C. What is a current-sense amplifier? A current-sense amplifier is a specialized analog IC that measures the small differential voltage developed across a shunt resistor carrying the load current, then amplifies that millivolt-level signal to a ground-referenced output that an ADC, microcontroller, or comparator can read. As a member of the power-management and amplifier IC hierarchy, the INA240 family combines a precision difference amplifier with PWM-rejection circuitry, allowing it to ignore large dV/dt transients from switching power stages while still maintaining high DC accuracy. Key features include 20 V/V gain (A1 variant), 132 dB DC common-mode rejection ratio (CMRR), a 1.5 MHz bandwidth, and 1.6 mA maximum quiescent supply current from a 2.7 V to 5.5 V supply rail. Enhanced PWM rejection suppresses transients from 60 V/ns common-mode slew events that occur when measuring current in motor-drive and solenoid circuits, allowing accurate readings through PWM edges without blanking. The INA240 architecture pairs an input EMI filter and chopper-stabilized front end with a precision output stage. The chopper stabilization shifts the 1/f noise to a higher frequency where it is filtered out, yielding the 5 uV/°C typical offset drift and 25 uV maximum input offset specified across the -40°C to +125°C operating range. Independent supply and common-mode ranges allow the IC to operate from a 3.3 V logic rail while sensing high-side current at 24 V, 36 V, or 48 V industrial bus voltages. Typical applications include 48 V brushed and brushless DC motor control, solenoid and valve current monitoring, server and telecom 12 V/24 V hot-swap current sensing, power-converter feedback, and battery-pack current monitoring in e-mobility and industrial robots. The A1 gain of 20 V/V suits low-side and high-side sensing where shunt full-scale drop is on the order of 75 mV. When designing with this device, choose the shunt resistor so that peak differential voltage at maximum load stays within the linear output range (typically 0.1 V to VS - 0.1 V), and place a 1 nF to 10 nF RC network on the input pins if the layout introduces parasitic common-mode noise. Use Kelvin (4-terminal) connection to the shunt to keep ground-loop errors out of the measurement. This page synthesizes real-time distributor pricing, drop-in alternatives, and design notes that go beyond the manufacturer datasheet, giving engineers a one-stop reference for the INA240A1PW.

RFC Hubungi kami
INA240A1PWR - 80V Bidirectional Current Sense Amp | TI TSSOP-8
INA240A1PWR

INA240A1PWR - 80V Bidirectional Current Sense Amp | TI TSSOP-8

The Texas Instruments INA240A1PWR is a -4 V to 80 V bidirectional, ultra-precise current-sense amplifier with enhanced PWM rejection, housed in an 8-pin TSSOP (PW) package with a fixed gain of 20 V/V. It senses drops across shunt resistors over a wide common-mode range independent of supply voltage and integrates a zero-drift chopper architecture that keeps input offset below 25 uV and offset drift below 100 nV/°C. What is a current-sense amplifier? A current-sense amplifier is a specialized analog IC that measures the small differential voltage developed across a shunt resistor carrying the load current, then amplifies that millivolt-level signal to a ground-referenced output that an ADC, microcontroller, or comparator can read. As a member of the power-management and amplifier IC hierarchy, the INA240 family combines a precision difference amplifier with PWM-rejection circuitry, allowing it to ignore large dV/dt transients from switching power stages while still maintaining high DC accuracy. Key features include 20 V/V gain (A1 variant), 132 dB DC common-mode rejection ratio (CMRR), a 1.5 MHz bandwidth, and 1.6 mA maximum quiescent supply current from a 2.7 V to 5.5 V supply rail. Enhanced PWM rejection suppresses transients from 60 V/ns common-mode slew events that occur when measuring current in motor-drive and solenoid circuits, allowing accurate readings through PWM edges without blanking. The INA240 architecture pairs an input EMI filter and chopper-stabilized front end with a precision output stage. The chopper stabilization shifts the 1/f noise to a higher frequency where it is filtered out, yielding the 5 uV/°C typical offset drift and 25 uV maximum input offset specified across the -40°C to +125°C operating range. Independent supply and common-mode ranges allow the IC to operate from a 3.3 V logic rail while sensing high-side current at 24 V, 36 V, or 48 V industrial bus voltages. Typical applications include 48 V brushed and brushless DC motor control, solenoid and valve current monitoring, server and telecom 12 V/24 V hot-swap current sensing, power-converter feedback, and battery-pack current monitoring in e-mobility and industrial robots. The A1 gain of 20 V/V suits low-side and high-side sensing where shunt full-scale drop is on the order of 75 mV. When designing with this device, choose the shunt resistor so that peak differential voltage at maximum load stays within the linear output range (typically 0.1 V to VS - 0.1 V), and place a 1 nF to 10 nF RC network on the input pins if the layout introduces parasitic common-mode noise. Use Kelvin (4-terminal) connection to the shunt to keep ground-loop errors out of the measurement. This page synthesizes real-time distributor pricing, drop-in alternatives, and design notes that go beyond the manufacturer datasheet, giving engineers a one-stop reference for the INA240A1PWR.

RFC Hubungi kami
INA240A2D - 50V/V Bidirectional Current-Sense Amplifier | Texas Instruments
INA240A2D

INA240A2D - 50V/V Bidirectional Current-Sense Amplifier | Texas Instruments

The Texas Instruments INA240A2D is a bidirectional, precision current-sense amplifier with a fixed gain of 50 V/V, a common-mode operating range from -4 V to 80 V, and an 8-pin SOIC package. It is designed to measure small shunt-resistor voltage drops while rejecting PWM-related transients, making it suitable for motor drives, solenoid controls, power converters, and battery systems. A current-sense amplifier is a specialized instrumentation amplifier that converts the differential voltage across a precision shunt resistor into a scaled voltage proportional to current. The INA240 belongs to the current-sense amplifier category and the broader amplifier and measurement IC hierarchy. Its bidirectional architecture supports both positive and negative current, while its negative common-mode capability allows operation below ground during the flyback interval of inductive loads. The A2 gain option provides 50 V/V amplification, allowing a small shunt drop to produce an easily measurable output. The -4 V to 80 V common-mode range supports low-voltage motor systems, industrial 24 V and 48 V buses, and automotive-style transient environments. The manufacturer identifies the device as an ultra-precise current-sense amplifier with enhanced PWM rejection. Its operating temperature range extends from -40 °C to +125 °C for industrial and automotive temperature-grade designs. The INA240 uses a differential input arrangement to reject supply ripple and common-mode voltage while measuring the shunt differential. Bidirectional operation allows the output to move above or below ground to indicate current direction. The 8-SOIC format supports conventional surface-mount assembly and provides a practical package for power-control boards where the shunt may be separated from sensitive analog circuitry. Typical uses include BLDC and brushed motor control, solenoid and relay current monitoring, DC-DC converter feedback, battery charge and discharge measurement, inverter leg monitoring, and industrial power-supply protection. The wide common-mode range is particularly useful when the sensed current is switched while the amplifier supply remains independent of the high-voltage power rail. Design the shunt and analog path carefully. Keep the differential input traces short and symmetric, place the amplifier close to the shunt, and use low-value resistors with appropriate pulse ratings. Input filtering must preserve the intended measurement bandwidth while attenuating high-frequency switching noise. Verify common-mode voltage, output swing, supply headroom, thermal performance, and amplifier saturation before committing the PCB layout. This page consolidates the device architecture, operating limits, application guidance, package details, sourcing workflow, and drop-in replacement analysis into one engineering reference. It also identifies where application-specific values must be calculated from the actual shunt resistance, current waveform, board environment, and power-supply topology.

RFC Hubungi kami
INA240A2DR - 50V/V Bidirectional Current Sense Amplifier | Texas Instruments
INA240A2DR

INA240A2DR - 50V/V Bidirectional Current Sense Amplifier | Texas Instruments

The Texas Instruments INA240A2DR is a bidirectional, zero-drift current-sense amplifier with a fixed gain of 50 V/V, a -4 V to 80 V common-mode input range, and enhanced PWM rejection. It is packaged in an 8-pin SOIC and operates from a single 5.5 V supply. A current-sense amplifier is a specialized amplifier that measures the voltage developed across a shunt resistor placed in a current-carrying conductor. The INA240 belongs to the current-sense amplifier hierarchy within instrumentation amplifiers and analog signal-chain ICs. It converts the small differential shunt voltage into an amplified voltage proportional to current, supporting both positive and negative current measurement. The A2 gain code sets the nominal amplification to 50 V/V. Its wide common-mode range permits sensing current above ground, at ground, and down to -4 V, which is useful in systems with inductive flyback or ground-offset returns. Bidirectional operation means that the output can represent positive or negative current without changing the basic shunt arrangement. Enhanced PWM rejection helps suppress switching disturbances commonly encountered in motor-control and power-conversion systems. The device uses a zero-drift architecture intended to provide accurate current measurement over changing temperatures and time. The manufacturer describes the INA240 family as ultra-precise and optimized for shunt-based measurements. Because the output is proportional to the shunt differential voltage, the shunt resistance determines the conversion between current and amplifier output voltage. Typical uses include motor and solenoid current monitoring, power-converter feedback, battery current measurement, industrial control systems, and automotive-style PWM systems. The 8-pin SOIC format supports conventional surface-mount assembly and compact analog layouts. Placement close to the shunt helps minimize pickup from adjacent switching nodes. Designers should verify the complete pin configuration, recommended input filtering, output-voltage range, and absolute maximum ratings in the manufacturer data sheet before layout. Kelvin routing from the shunt terminals and careful grounding are especially important because small differential signals can be corrupted by shared copper impedance or high-current return paths. This page combines the manufacturer's core INA240 characteristics with exact-MPN commercial information, same-family drop-in options, application guidance, and practical PCB considerations for engineers evaluating the INA240A2DR in a current-measurement design.

RFC Hubungi kami
INA240A2PW - 50V/V Bidirectional Current Sense Amp | Texas Instruments
INA240A2PW

INA240A2PW - 50V/V Bidirectional Current Sense Amp | Texas Instruments

Texas Instruments INA240A2PW is a bidirectional, precision current-sense amplifier with a gain of 50 V/V, a -4 V to +80 V common-mode voltage range, and an operating temperature range of -40 °C to +125 °C. The device is packaged in an 8-pin TSSOP (PW) package and is designed for high-side or low-side current measurement in systems exposed to fast common-mode transients. A current-sense amplifier is an instrumentation amplifier that measures the small voltage developed across a current shunt and converts it into an amplified voltage proportional to current. This device belongs to the instrumentation-amplifier and current-sense-amplifier hierarchy, where its differential measurement, low offset voltage, and common-mode rejection improve the accuracy of power, motor, solenoid, and battery monitoring systems. The A2 gain option provides 50 V/V amplification. The INA240 family operates from a 5.5 V supply and accepts common-mode voltages extending from -4 V to +80 V. Its enhanced PWM rejection is intended to suppress transient disturbance caused by switching power stages, while bidirectional operation allows measurement of positive or negative current without changing the signal path architecture. The common-mode range and PWM rejection make the INA240A2PW especially useful where the shunt is placed near a motor, actuator, or inductive load. Although the analog output must remain within the amplifier's supply-voltage limits, the input common-mode voltage can move independently across the stated -4 V to +80 V range. This separation between input common-mode capability and output-supply limits is central to correct application design. Typical uses include DC motor current control, solenoid and actuator monitoring, battery pack current measurement, industrial power conversion, and electronic loads. The precision architecture is also appropriate for systems that must recover a small shunt voltage accurately while rejecting rapidly changing voltages on the sensed power rail. For layout, route the two shunt connections as a compact, symmetric pair and minimize the area enclosed by those traces. Place the shunt and amplifier input network close together, use a low-value differential filter only where its added noise and settling behavior are acceptable, and terminate the amplifier output according to the ADC or analog front-end requirements. This page combines the manufacturer lifecycle information, verified distributor records, family-level alternatives, comparison criteria, and application-oriented design guidance for engineers evaluating the INA240A2PW as a current-sense amplifier for industrial and power-conversion systems.

RFC Hubungi kami
INA240A3D - 80V Current Sense Amplifier | Texas Instruments
INA240A3D

INA240A3D - 80V Current Sense Amplifier | Texas Instruments

The Texas Instruments INA240A3D is a bidirectional, ultra-precise voltage-output current-sense amplifier with an operating common-mode range of -4 V to 80 V, enhanced PWM rejection, and an 8-pin SOIC package. It is designed to measure the voltage developed across a shunt resistor in high-side or low-side current-sensing circuits while supporting common-mode voltages above the device supply voltage. A current-sense amplifier is a specialized amplifier within the instrumentation-amplifier and signal-conditioning hierarchy. It converts the small differential voltage produced by a shunt resistor into a proportional analog voltage suitable for measurement by an ADC, MCU, motor controller, or protection circuit. The INA240 family is classified as an analog signal-chain IC and is commonly placed beside a power-conversion stage to create a precision current-feedback signal. The INA240A3D combines bidirectional measurement, a wide -4 V to 80 V common-mode range, and enhanced PWM rejection. Bidirectional operation allows the output polarity to represent either positive or negative current. The negative common-mode capability is useful when a shunt is observed during a below-ground flyback interval, while the upper range supports current monitoring in systems operating well above the amplifier supply voltage. Its stated operating-temperature range is -40 °C to 125 °C. The device uses a voltage-output architecture with reference and supply connections that support system-level current measurement. Because the amplifier can operate independently of the common-mode voltage being sensed, its performance is maintained in applications where the shunt voltage swings rapidly while the amplifier remains powered from a low-voltage rail. This architecture is particularly useful in motor drives, solenoid controls, power converters, and battery-powered systems where a conventional low-voltage current-sense amplifier may leave the measurement range. Typical uses include high-side DC-link monitoring, low-side motor-return measurement, solenoid current diagnostics, power-supply telemetry, and battery charge or discharge current sensing. In these systems, the shunt is placed in the current path and connected to the differential input of the INA240A3D. The resulting analog voltage can be routed to a control ADC or comparator for regulation, fault detection, or data logging. Design the input and reference network carefully because the differential shunt voltage, amplifier supply, output range, and selected shunt resistance jointly determine usable measurement range. Keep the shunt and amplifier connections compact to minimize parasitic pickup, use a Kelvin connection where practical, and route the differential pair away from switching-node copper. The manufacturer's INA240 datasheet should be used for pin assignments, gain, input limits, output behavior, and recommended application values. This page organizes the verified INA240A3D operating limits, package information, sourcing details, replacement constraints, application guidance, and design considerations. It also distinguishes a confirmed same-package automotive alternative from incompatible package or gain variants that cannot be treated as drop-in replacements.

RFC Hubungi kami
INA240A3DR - 80V Current Sense Amplifier | Texas Instruments (Tape & Reel)
INA240A3DR

INA240A3DR - 80V Current Sense Amplifier | Texas Instruments (Tape & Reel)

The Texas Instruments INA240A3DR is a bidirectional, ultra-precise voltage-output current-sense amplifier with an operating common-mode range of -4 V to 80 V, enhanced PWM rejection, and an 8-pin SOIC package. It is designed to measure the voltage developed across a shunt resistor in high-side or low-side current-sensing circuits while supporting common-mode voltages above the device supply voltage. A current-sense amplifier is a specialized amplifier within the instrumentation-amplifier and signal-conditioning hierarchy. It converts the small differential voltage produced by a shunt resistor into a proportional analog voltage suitable for measurement by an ADC, MCU, motor controller, or protection circuit. The INA240 family is classified as an analog signal-chain IC and is commonly placed beside a power-conversion stage to create a precision current-feedback signal. The INA240A3DR combines bidirectional measurement, a wide -4 V to 80 V common-mode range, and enhanced PWM rejection. Bidirectional operation allows the output polarity to represent either positive or negative current. The negative common-mode capability is useful when a shunt is observed during a below-ground flyback interval, while the upper range supports current monitoring in systems operating well above the amplifier supply voltage. Its stated operating-temperature range is -40 °C to 125 °C. The device uses a voltage-output architecture with reference and supply connections that support system-level current measurement. Because the amplifier can operate independently of the common-mode voltage being sensed, its performance is maintained in applications where the shunt voltage swings rapidly while the amplifier remains powered from a low-voltage rail. This architecture is particularly useful in motor drives, solenoid controls, power converters, and battery-powered systems where a conventional low-voltage current-sense amplifier may leave the measurement range. Typical uses include high-side DC-link monitoring, low-side motor-return measurement, solenoid current diagnostics, power-supply telemetry, and battery charge or discharge current sensing. In these systems, the shunt is placed in the current path and connected to the differential input of the INA240A3DR. The resulting analog voltage can be routed to a control ADC or comparator for regulation, fault detection, or data logging. Design the input and reference network carefully because the differential shunt voltage, amplifier supply, output range, and selected shunt resistance jointly determine usable measurement range. Keep the shunt and amplifier connections compact to minimize parasitic pickup, use a Kelvin connection where practical, and route the differential pair away from switching-node copper. The manufacturer's INA240 datasheet should be used for pin assignments, gain, input limits, output behavior, and recommended application values. This page organizes the verified INA240A3DR operating limits, package information, sourcing details, replacement constraints, application guidance, and design considerations. It also distinguishes a confirmed same-package automotive alternative from incompatible package or gain variants that cannot be treated as drop-in replacements.

RFC Hubungi kami
INA240A4D - 80V Bidirectional Current Sense Amp | Texas Instruments
INA240A4D

INA240A4D - 80V Bidirectional Current Sense Amp | Texas Instruments

The Texas Instruments INA240A4D is a bidirectional, zero-drift current-sense amplifier with a -4 V to 80 V common-mode range, enhanced PWM rejection, and an 8-pin SOIC package. It operates across a -40 °C to +125 °C temperature range and is designed to measure the voltage across a shunt resistor in systems where the sensed bus can move below ground or as high as 80 V. A current-sense amplifier is an instrumentation amplifier that converts the small differential voltage developed across a shunt resistor into a proportional, amplified output voltage. The INA240 family belongs to the amplifier and instrumentation-amplifier hierarchy, where precision gain, input offset behavior, common-mode rejection, and output accuracy determine how accurately a power circuit can be monitored. Bidirectional sensing allows the same device to report positive or negative current without changing the measurement topology. The INA240A4D provides 120 dB CMRR, a 100 kHz gain-bandwidth product, approximately 90 µA input bias current, and 1.8 mA operating supply current. Its zero-drift architecture supports current measurements in motor controls, solenoid drivers, battery systems, and industrial power supplies. Enhanced PWM rejection helps preserve measurement accuracy when rapid common-mode voltage transitions are present around inductive loads. The common-mode rating is independent of the amplifier supply voltage, allowing the INA240A4D to operate with a separate low-voltage supply while monitoring a high-voltage power bus. Its negative common-mode capability is particularly useful during the flyback interval of typical solenoid applications, when the voltage at the monitored node can fall below ground. The broad 80 V positive range supports higher-voltage industrial and automotive-style systems. Typical applications include motor-current feedback, solenoid-current monitoring, battery-pack current measurement, inverter control, power-supply telemetry, and current sharing. In each case, the shunt resistor converts current into a differential voltage, while the amplifier provides a measurable output for an ADC, controller, or protection circuit. Bidirectional operation is useful where energy can flow in either direction. For layout, place the shunt and input network close to the amplifier, keep the differential input traces compact and matched, and provide a stable bypass connection near the supply pins. The input filtering and gain-setting network must be checked against the intended current range because shunt resistance, amplifier gain, and ADC input range jointly determine the usable measurement span. This product overview combines the manufacturer specifications, package details, sourcing status, and application guidance needed to evaluate the INA240A4D. Because the manufacturer identifies this orderable variant as no longer in production, engineers should confirm lifecycle status and consider an active alternate during new design qualification.

RFC Hubungi kami
INA250A1PW - 36V Bidirectional Current-Sense Amplifier | TI
INA250A1PW

INA250A1PW - 36V Bidirectional Current-Sense Amplifier | TI

The Texas Instruments INA250A1PW is a bidirectional, precision current-sense amplifier with an integrated shunt resistor, a 36 V common-mode range, and a gain of 20 V/V in a 16-pin TSSOP (PW) package. It is designed to measure positive and negative current while the measured conductor operates from 0 V to 36 V, independent of the amplifier supply voltage. The integrated precision shunt removes the external shunt-resistor element while preserving calibrated current measurement. A current-sense amplifier is a specialized instrumentation amplifier that converts the voltage across a current-sensing resistor into a proportional, low-level output voltage. The INA250 belongs to the current-sense amplifier hierarchy, where it supports precision measurement, power monitoring, motor control, industrial instrumentation, and protection systems. Its integrated shunt also reduces board area compared with a discrete shunt-resistor implementation. The device provides bidirectional measurement through an externally applied reference voltage. Positive current can move the output above the reference level, while negative current moves it below that level. This arrangement allows a unidirectional amplifier output to represent both load directions and supports applications that need absolute-value or signed-current information. The 0 V to 36 V common-mode range covers many industrial, automotive-adjacent, power-supply, and motor-system rails. The INA250A1PW uses the A1 gain option, which provides 20 V/V voltage gain. Its voltage-output architecture simplifies connection to analog-to-digital converters, comparators, controllers, and monitoring systems. Because the sensing element is integrated, PCB design must preserve the defined current path and provide adequate copper width and thermal capacity for the intended current level. The TSSOP package is a surface-mount package in the TSSOP-16 family. Typical applications include high-side power-supply monitoring, bidirectional motor-current measurement, industrial control systems, battery current sensing, solenoid monitoring, and electronic protection. In these systems, the amplifier reconstructs a current-proportional voltage that can be digitized or compared with a threshold. System calibration should account for the selected gain, reference voltage, ADC resolution, and the measurement bandwidth required by the load. Design attention should focus on Kelvin routing for the reference connection, filtering around the output when the measured waveform contains high-frequency noise, and thermal verification at maximum continuous current. The integrated shunt is convenient, but PCB copper, vias, pads, and connector geometry can limit practical current and increase temperature rise. Use the manufacturer pin-description table when assigning PCB tracks and the device data sheet for the complete recommended layout. This page combines the manufacturer device description, package and operating information, practical application guidance, replacement criteria, and engineering-oriented design notes. These resources help engineers evaluate the INA250A1PW beyond a basic distributor listing while keeping pin compatibility and measurement accuracy at the center of the selection process.

RFC Hubungi kami
INA250A3PW - 36V Bidirectional Current Sense Amplifier | TI
INA250A3PW

INA250A3PW - 36V Bidirectional Current Sense Amplifier | TI

Texas Instruments INA250A3PW is a bidirectional precision current-sense amplifier with an integrated shunt resistor, 100 V/V gain, and operation from a 2.7 V to 36 V supply. The device measures low- and high-side current across common-mode voltages from 0 V to 36 V and is housed in a 16-pin TSSOP package. Its voltage output supports direct connection to analog-to-digital converters, controllers, and monitoring systems. A current-sense amplifier converts the voltage generated across a shunt resistor into a proportional, measurable voltage. This integrated-resistor implementation belongs to the current-shunt monitor class within precision amplifier and power-management ICs. By placing the shunt inside the amplifier package, it removes the need for a separate precision shunt while reducing layout sensitivity associated with external Kelvin connections. The INA250A3PW provides a gain of 100 V/V, allowing the 50 mΩ integrated shunt to support current measurements up to 15 A according to the family specifications. Bidirectional operation measures positive or negative current, and an external reference can establish the output operating point for zero-current offset or bipolar reporting. A 2.7 V minimum supply permits use in low-voltage systems while the 36 V supply rating supports higher-voltage industrial buses. The INA250 family specifies a maximum supply current of 300 µA and operation from -40 °C to 125 °C. Its integrated shunt and Kelvin-connected internal structure improve measurement accuracy by reducing lead and trace resistance effects. The voltage-output architecture requires downstream filtering and input/output stability capacitors selected according to the manufacturer datasheet, rather than relying on an internal shunt resistor placed outside the package. Typical applications include motor and solenoid current monitoring, power-supply telemetry, battery-pack management, industrial control systems, and high-side or low-side protection. The device can monitor current in systems whose supply voltage changes independently of the sensed common-mode voltage, making it useful in 24 V industrial equipment, automotive-style loads, and distributed power architectures. Design layouts should keep the power path short and use solid copper planes so that shunt heat is distributed rather than concentrated in a narrow trace. Confirm output saturation, reference-pin behavior, common-mode limits, and filter-component values against the manufacturer datasheet before operating at the 15 A family limit. This page combines device specifications, application guidance, pin and package considerations, lifecycle information, and verified replacement analysis. It also distinguishes electrically similar family members from true pin-compatible drop-in choices so that PCB reuse decisions are based on measurable electrical differences rather than package similarity alone.

RFC Hubungi kami
INA293B1QDBVRQ1 - 110V, 1.3MHz Current Sense Amp | TI
INA293B1QDBVRQ1

INA293B1QDBVRQ1 - 110V, 1.3MHz Current Sense Amp | TI

The Texas Instruments INA293B1QDBVRQ1 is an AEC-Q100 qualified, ultra-precise bidirectional current-sense amplifier that measures voltage drops across shunt resistors over an exceptionally wide common-mode range from -4 V to +110 V. It delivers a 1.3 MHz small-signal bandwidth with a 20 V/V fixed gain (B1 variant) in a 5-pin SOT-23 (DBV) package, making it ideal for high-voltage, high-precision current monitoring in space-constrained automotive and industrial designs. What is a current-sense amplifier? A current-sense amplifier is a specialized analog building block that measures the small differential voltage developed across a shunt resistor placed in series with a load or supply rail, and converts it to a ground-referenced output voltage proportional to load current. Unlike a general-purpose op amp, a current-sense amplifier tolerates large common-mode voltages - often well above its own supply - and rejects the common-mode component, exposing only the shunt drop. The INA293-Q1 sits at the high-precision end of this category, combining low offset, low drift, and the widest common-mode range in TI's portfolio of unidirectional/bidirectional current-sense amplifiers. Key features include a maximum offset voltage of ±30 µV across temperature, ±0.2% gain error, and a quiescent current of approximately 1.5 mA over the -40 °C to +125 °C automotive grade-1 temperature range. The B1 gain variant provides 20 V/V; the B2, B3, B4, and B5 variants in the same family offer 50 V/V, 100 V/V, 200 V/V, and 500 V/V respectively, all sharing the SOT-23-5 footprint. The device operates from a single 2.7 V to 20 V supply and is robust against input transients well beyond its supply rail. Internally, the INA293-Q1 uses a precision chopped-input front end followed by a fixed-gain output stage, achieving CMRR greater than 100 dB at DC and PSRR above 80 dB at 1 kHz. The wide common-mode architecture supports both high-side and low-side sensing topologies, enabling accurate monitoring in 48 V mild-hybrid automotive systems, industrial 24 V/36 V/48 V rails, and telecom -48 V applications without level shifting. Typical applications include 48 V eMobility battery management, BLDC motor phase-current monitoring, server/AI accelerator hot-swap current telemetry, USB Power Delivery contract current sensing, and solar inverter string monitoring. Compared with isolated current transducers, the INA293-Q1 achieves comparable accuracy at a fraction of the BOM cost and PCB area. When designing with this device, place the shunt resistor as close as possible to the input pins and keep the input traces symmetrical to preserve CMRR. A 0.1 µF supply bypass capacitor placed within 5 mm of the V+ pin is recommended for stable operation across the full -4 V to +110 V common-mode range. This page synthesizes distributor pricing, drop-in alternatives from the INA293-Q1 family and competing high-side current-sense amplifiers, and practical design notes that go beyond the manufacturer datasheet.

RFC Hubungi kami
INA333AIDGKR - 50uA Zero-Drift INA | Texas Instruments
INA333AIDGKR

INA333AIDGKR - 50uA Zero-Drift INA | Texas Instruments

The Texas Instruments INA333AIDGKR is a low-power, precision, zero-drift instrumentation amplifier with a 1.8 V to 5.5 V supply range, 10 uV typical input offset voltage, 150 kHz bandwidth, and an 8-pin VSSOP (DGK) package. It uses a three-operational-amplifier architecture and one external gain-setting resistor to provide gains from 1 to 1000. An instrumentation amplifier is a differential analog amplifier optimized for measuring small voltage signals superimposed on larger common-mode voltages. Its internal three-op-amp topology provides high input impedance and accurate differential gain, making it more practical than a discrete difference amplifier when source impedances are unequal or signals arrive from sensors. INA333 belongs to the precision amplifier hierarchy: instrumentation amplifier, operational amplifier, analog IC, and semiconductor. The INA333 emphasizes low power, low offset drift, and rail-to-rail output operation. Verified source data identifies a 50 uA typical supply current and a gain equation of G = 1 + 100 kΩ/RG. The 150 kHz bandwidth supports fast sensor signals, while the 10 uV input offset specification improves measurement resolution around the zero-input condition. Its input stage is designed to reject common-mode variation encountered in bridge, current-sense, and portable sensing systems. The zero-drift architecture reduces temperature-related offset movement, helping preserve measurement stability when the sensor signal is small relative to input offset. Rail-to-rail output increases usable output swing on low-voltage supplies, although engineers must still verify input common-mode range, output swing, bandwidth, and input bias behavior across the complete intended voltage and temperature range using the manufacturer datasheet. Typical uses include portable medical monitoring, battery-powered industrial instrumentation, pressure and load-cell signal conditioning, low-side current measurement, and low-voltage sensor acquisition. The 50 uA power budget is especially useful for wearable and remote systems where every microamp affects battery life. The VSSOP-8 package supports compact layouts, but differential routing and gain-resistor placement remain essential. For best results, connect the gain resistor close to the RG pins, use a low-noise reference supply, maintain symmetric input routing, and follow the datasheet bypass recommendations. Verify common-mode limits at every operating point rather than assuming rail-to-rail input. This page combines verified distributor data, manufacturer specifications, sourcing guidance, and practical design context.

RFC Hubungi kami
INA333SHKQ - Zero-Drift Instrumentation Amplifier | Texas Instruments
INA333SHKQ

INA333SHKQ - Zero-Drift Instrumentation Amplifier | Texas Instruments

Texas Instruments INA333SHKQ is a micro-power, zero-drift, rail-to-rail output instrumentation amplifier with a closed-loop gain range of 100 to 1000 V/V. It is offered in an 8-pin HKQ ceramic flat package and is rated for operation from -55°C to +210°C. The high-temperature grade makes the device suitable for precision sensing systems that require stable amplification under extended thermal exposure. An instrumentation amplifier is a specialized analog amplifier optimized for measuring small differential signals while rejecting common-mode interference. Its internal differential architecture preserves signal integrity when the inputs share substantial common-mode voltage. Within the broader semiconductor hierarchy, an instrumentation amplifier belongs to the amplifier IC family and combines precision input, gain-setting, and differential-to-single-ended conversion functions in one device. The INA333SHKQ supports closed-loop gains from 100 to 1000 V/V. At a gain of 100, the manufacturer lists a maximum input offset voltage of 25 µV, a typical drift of 0.2 µV/°C, and noise density of 55 nV/√Hz. Its listed common-mode rejection is at least 100 dB at a gain of 10. These characteristics make the amplifier suitable for bridge-based sensors where small millivolt-level differential outputs must be measured accurately. The device operates from a single 1.8 V to 3.5 V supply according to the INA333 family specifications. Its rail-to-rail output stage permits the output voltage to approach the supply limits, improving utilization of low-voltage signal chains. A single external resistor sets the gain, simplifying implementation while preserving accurate differential amplification. The micro-power operating current supports battery-operated instrumentation where continuous sensor monitoring is required without excessive load. Typical uses include pressure and force transducers, thermocouple and RTD interfaces, biomedical instrumentation, portable measurement systems, and industrial process-control equipment. The -55°C to +210°C operating range distinguishes the SHKQ grade from the standard commercial INA333 variants and supports use in high-temperature measurement environments. When laying out an INA333SHKQ circuit, route the differential input and gain-resistor connections as short, symmetric traces, and place input filtering close to the source. Check common-mode input limits at the selected supply voltage because the allowable input range is not independent of supply. Confirm output headroom at the required gain and load, especially in low-voltage systems where rail-to-rail output behavior is important. This page combines the high-temperature INA333SHKQ specifications with application guidance, package information, engineering design notes, and a careful drop-in replacement assessment. It is intended to help engineers determine whether the device fits a precision sensing application without overlooking gain, temperature, supply, or PCB-footprint constraints.

RFC Hubungi kami
INA333SJD - Precision Micro-Power Instrumentation Amplifier | TI
INA333SJD

INA333SJD - Precision Micro-Power Instrumentation Amplifier | TI

Texas Instruments INA333SJD is a low-power, zero-drift, rail-to-rail-output instrumentation amplifier packaged in an 8-pin SOIC-8 (JD) package. Its headline characteristics include a 1.8 V to 5.5 V supply range, 150 kHz gain-bandwidth product, 10 µV offset voltage, and 2 nA input bias current. The device is intended for precision low-level sensor measurements where low offset, low drift, high common-mode rejection, and low input bias current are more important than wide bandwidth. An instrumentation amplifier is a differential-input amplifier designed to amplify a small voltage difference between two inputs while rejecting common-mode voltage. The INA333 belongs to the broader zero-drift amplifier family, combining an instrumentation-amplifier architecture with chopper-stabilized low-offset behavior. A zero-drift amplifier continuously corrects its own offset error, allowing low input-referred offset to remain stable over time and temperature. The INA333SJD supports gains of 1, 10, 100, and 1000 through its RG pin. Manufacturer specifications identify a maximum offset voltage of 25 µV at a gain of 100, offset drift of 0.2 µV/°C at a gain of 1000, input noise of 55 nV/√Hz at a gain of 100, and minimum common-mode rejection of 100 dB at a gain of 10. Its 0.16 V/µs slew rate supports relatively slow sensor signals without requiring a high-speed amplifier. The rail-to-rail output allows the output voltage to approach the supply rails, improving usable signal range in low-voltage systems. Gain is established by a single external resistor on the RG pin, simplifying circuit implementation while keeping the gain-setting component outside the amplifier. The measured gain error also depends on the tolerance and temperature coefficient of that resistor, so precision applications should use a suitable resistor network. Typical uses include bridge-based pressure and strain measurements, low-current sensors, biomedical instrumentation, industrial process monitoring, and portable sensor systems. The device is particularly useful when sensor output is small, common-mode voltage is substantial, and thermal offset variation would otherwise dominate the measurement. The principal design trade-off is bandwidth versus precision: the INA333 prioritizes low offset and low drift, while its 150 kHz gain-bandwidth product is modest compared with general-purpose high-speed amplifiers. Designers should also evaluate the high-temperature variant indicated by the INA333SJD ordering information and verify the complete electrical limits for the intended operating range. This product page consolidates the verified manufacturer and distributor details, identifies the practical benefits of zero-drift operation, and organizes the device's gains, noise, offset, supply, package, and application constraints for faster engineering selection.

RFC Hubungi kami
INA4180AIPWR-Q1 - Quad 26V Current Sense Amp, 20 V/V | TI
INA4180AIPWR-Q1

INA4180AIPWR-Q1 - Quad 26V Current Sense Amp, 20 V/V | TI

The Texas Instruments INA4180AIPWR-Q1 is an automotive-grade, quad-channel voltage-output current-sense amplifier (current-shunt monitor) in a 14-pin TSSOP (PW) package. It senses voltage drops across current-sense resistors at common-mode voltages from -0.2 V to +26 V, independent of the 1.7 V to 5.5 V supply, with a fixed gain of 20 V/V (A1 version) and 350 kHz bandwidth. A current-sense amplifier is a specialized difference amplifier that measures the small voltage developed across a shunt resistor and converts it into a ground-referenced output signal. Within the power-management IC hierarchy, it sits between the shunt element and an ADC or controller, enabling precise current monitoring for system control and protection in automotive and industrial power rails. Key features include the wide -0.2 V to 26 V common-mode range that survives load-dump and cold-crank conditions without external circuitry, four independent amplifiers in one package that reduce BOM cost and board area in multi-rail designs, rail-to-rail output for maximum ADC dynamic range, and offset voltage as low as [DATA_NEEDED: Vos]. The extended -40C to +125C operating range and AEC-Q100 qualification make it suitable for under-hood and body electronics applications. Architecturally, the INAx180 family integrates a precision matched resistor network that sets the gain (A1 = 20 V/V, A2 = 50 V/V, A3 = 100 V/V, A4 = 200 V/V), eliminating external gain-setting resistors and their matching errors. The zero-crossover-compatible input stage supports sensing on the low side or high side of the rail, and the output is referenced to ground regardless of common-mode voltage. Typical applications include automotive battery current monitoring, 48V and 12V board-net supervision, electric power steering motor current feedback, DC-DC converter current loops, and industrial PLC analog input modules. Cost-optimized designs benefit from the quad-channel integration. Design tip: choose the shunt resistor so the full-scale drop is 10-50 mV to balance accuracy against power dissipation, and use Kelvin (4-wire) connections to the shunt for best precision. Pricing shown as of 2026-08-29.

RFC Hubungi kami
INA597IDGKT - Precision 2MHz Difference Amplifier | TI
INA597IDGKT

INA597IDGKT - Precision 2MHz Difference Amplifier | TI

The INA597IDGKT is a high-precision, wide-bandwidth difference amplifier from Texas Instruments, designed for cost-sensitive applications requiring accurate differential signal measurement. It integrates a precision operational amplifier with a matched resistor network, achieving a maximum offset voltage of 200 µV and an offset drift of 5 µV/°C. The device operates from a single supply of 4.5 V to 36 V or dual supplies of ±2.25 V to ±18 V, with a bandwidth of 2 MHz and a common-mode rejection ratio (CMRR) of 88 dB. Housed in an 8-pin VSSOP (DGK) package, the INA597IDGKT is suitable for space-constrained designs. A difference amplifier is a type of operational amplifier circuit that amplifies the voltage difference between two inputs while rejecting common-mode voltages. It is a fundamental building block in analog signal processing, often used in current sensing, bridge amplification, and precision measurement systems. The INA597 belongs to the broader category of instrumentation amplifiers, which are specialized for accurate differential signal acquisition in noisy environments. Key features of the INA597IDGKT include its low offset voltage and drift, which ensure accurate measurement over temperature, and its high CMRR of 88 dB, which rejects common-mode noise. The device also offers rail-to-rail output, allowing maximum dynamic range in single-supply applications. Its low power consumption makes it ideal for battery-powered and portable instrumentation. The INA597 uses TI's e-trim™ technology, which provides precision trimming of the internal resistor network to achieve excellent gain accuracy and temperature stability. The integrated resistors are laser-trimmed to maintain tight matching, ensuring consistent performance across the operating temperature range. The device is fully specified for operation from -40°C to +125°C, making it suitable for industrial and automotive environments. Typical applications include motor current sensing, battery management systems, and precision data acquisition. In motor control, the INA597IDGKT can measure the voltage across a shunt resistor to monitor current, providing feedback for closed-loop control. In battery management, it can sense charge/discharge currents with high accuracy. The device's wide supply range and rail-to-rail output also make it suitable for industrial process control and test equipment. When designing with the INA597IDGKT, ensure that the input common-mode voltage remains within the specified range to maintain linearity. The reference pin (REF) allows level shifting of the output, which is useful in single-supply applications where the output must be centered at a specific voltage. Proper PCB layout with short traces and adequate bypassing will optimize performance.

RFC Hubungi kami
INA790A-Q1 - 110V 75ARMS Ultra-Precise Current Sense Amp | TI
INA790A-Q1

INA790A-Q1 - 110V 75ARMS Ultra-Precise Current Sense Amp | TI

The Texas Instruments INA790A-Q1 is an AEC-Q100 qualified, 110V, 75ARMS integrated-shunt ultra-precision current-sense amplifier with enhanced PWM rejection, housed in a 15-VSON (DEK) 6x6 mm package. It combines a calibrated 400 micro-ohm Kelvin-connected shunt resistor with a zero-drift chopped amplifier, delivering +/-35 ppm/degrees C temperature drift and bidirectional current measurement from -4V to +110V common-mode. What is a current-sense amplifier? A current-sense amplifier is an analog IC that measures the voltage across a shunt resistor placed in series with a load and amplifies the small differential voltage into a ground-referenced output proportional to load current. Current-sense amplifiers sit within the signal-chain hierarchy as follows: current-sense amplifier -> instrumentation amplifier -> analog amplifier -> power management analog IC. INA790A-Q1 belongs to the integrated-shunt subfamily, where the shunt resistor and the gain stage are co-packaged, eliminating PCB layout-induced Kelvin errors and parasitic resistance drift that plague discrete solutions. Key features include a -4V to +110V wide common-mode range that survives load-dump and cold-crank transients in 48V automotive rails, 75ARMS continuous current handling, enhanced PWM rejection that suppresses large dv/dt common-mode steps from switching power stages, 1.3 MHz bandwidth for fast transient response, and a low 35 ppm/degrees C maximum temperature drift enabled by the chopper-stabilized architecture. The integrated 400 micro-ohm shunt eliminates external resistor stocking, drift concerns, and board-space overhead. The INA790A-Q1 uses a zero-drift chopper architecture that modulates the input offset voltage to a higher frequency, samples the modulation envelope, and feeds back to cancel the original offset. This technique virtually eliminates the 1/f noise corner and the offset drift that limit conventional current-sense amplifiers in high-precision DC and slow-varying measurements. Typical applications include 48V automotive BLDC motor phase current sensing, server and telecom hot-swap controller current monitors, industrial solenoid and actuator current feedback, solar inverter string current measurement, and battery management system (BMS) pack-current sensing. The AEC-Q100 Grade 1 qualification and PWM rejection make it specifically tailored to inverter and motor-drive environments. When designing with this device, place the INA790A-Q1 in the Kelvin path as close to the load current shunt as possible. Because the shunt is internal, the only PCB layout concern is keeping high-current traces off the analog ground return. Use the REF pin to level-shift the output for bidirectional sensing into an ADC with a ground-referenced input. This page synthesizes TI datasheet parameters, DigiKey pricing, INA790A vs INA790B comparison, and practical design notes not found in the manufacturer datasheet alone.

RFC Hubungi kami
INA791B-Q1 - 110V 75A High-Bandwidth Current Sense Amp | Texas Instruments
INA791B-Q1

INA791B-Q1 - 110V 75A High-Bandwidth Current Sense Amp | Texas Instruments

The Texas Instruments INA791B-Q1 is an AEC-Q100-qualified, ultra-precise bidirectional current-sense amplifier with integrated 75A EZShunt technology, supporting a common-mode voltage range of -4V to +110V independent of supply. Housed in a 14-pin DFN (DEK) package measuring approximately 2.5 mm x 3 mm, the B-grade variant offers enhanced precision over the A-grade, including tighter gain error and offset drift specifications optimized for high-accuracy current measurement in automotive and industrial systems. A current-sense amplifier is an analog IC that measures the small differential voltage developed across a shunt resistor carrying a large load current, while rejecting the large common-mode voltage present at the shunt terminals. The category belongs to the instrumentation amplifier family, itself a subclass of operational amplifiers used in measurement and protection subsystems. Current-sense amplifiers sit in the signal chain between the power stage and the MCU/ADC, enabling telemetry, overcurrent protection, and closed-loop control in DC/DC converters, motor drivers, and battery management systems. Key features of the INA791B-Q1 include a wide -4V to +110V common-mode range, high bandwidth for fast transient response, support for 75A RMS continuous current via the integrated EZShunt resistor, and a single 2.7V to 5.5V supply drawing only 3.75 mA maximum quiescent current. The B-grade variant delivers tighter initial accuracy and lower drift than the A-grade, making it well-suited to precision telemetry across the automotive temperature range of -40C to +125C. The architecture combines a precision chopper-stabilized front end with an EZShunt integrated shunt element, eliminating external sense resistors while maintaining high CMRR across the entire common-mode range. The device outputs an analog voltage proportional to load current that can be routed directly to an ADC input for software-based current monitoring, fault detection, and coulomb counting. Typical applications include 48V automotive electrical systems, battery management in HEV/EV powertrains, motor control in body and chassis ECUs, solenoid and actuator monitoring, and industrial high-voltage bus telemetry. The integrated shunt simplifies PCB layout and reduces parasitic inductance that otherwise degrades high-di/dt measurement accuracy. When designing with this part, route the high-current path directly through the integrated EZShunt pins to minimize parasitic resistance, and place a low-ESR decoupling capacitor close to the VS pin. The bidirectional capability means the output polarity indicates current direction, which simplifies charge/discharge monitoring in battery systems.

RFC Hubungi kami