Produk (46,000+)

LMH6624MAX/ - 1.5GHz Low Noise Op Amp | Texas Instruments
LMH6624MAX/

LMH6624MAX/ - 1.5GHz Low Noise Op Amp | Texas Instruments

The Texas Instruments LMH6624MAX/ is a single-channel, ultra-low-noise, wideband voltage-feedback operational amplifier housed in an 8-pin SOIC (MAX package suffix) that delivers 1.5 GHz gain-bandwidth product, 0.92 nV/√Hz input voltage noise density, and 2.3 pA/√Hz input current noise density. The amplifier combines this wideband AC performance with low DC errors including 100 µV typical input offset voltage and ±0.1 µV/°C drift, enabling closed-loop gains above 10 in both inverting and non-inverting configurations. It operates from ±2.5 V to ±6 V dual supply or 5 V to 12 V single supply. A voltage-feedback op amp is a class of analog amplifier whose closed-loop bandwidth is set by the feedback network rather than the op amp's internal gain, allowing designers to trade gain for bandwidth. Voltage-feedback amplifiers (VFAs) sit within the broader operational amplifier hierarchy, which includes current-feedback amplifiers (CFAs), instrumentation amplifiers, and precision chopper-stabilized amplifiers. The LMH6624 family targets wideband precision signal chains where low noise and low DC error must coexist at high frequency. Key features include 1.5 GHz gain-bandwidth, 0.92 nV/√Hz input noise, 2.3 pA/√Hz current noise, 100 µV VOS, ±0.1 µV/°C drift, 1500 V/µs typical slew rate, and 70 mA output current. The wide supply range supports ±2.5 V to ±6 V dual or 5 V to 12 V single-supply operation. The SOIC-8 surface-mount package offers a thermal resistance around 150 C/W and supports -40 °C to +125 °C ambient operation. The device uses a bipolar transistor input stage and complementary bipolar output stage, allowing rail-to-rail output swing within ~0.7 V of either supply. The architecture balances voltage noise and current noise favorably for source impedances in the 1 kΩ to 50 kΩ range, which is the sweet spot for photodiode transimpedance, ADC buffers, and ultrasonic preamps. Typical applications include photodiode transimpedance amplifiers, ultrasonic preamps, IF/RF signal-chain buffers, high-speed ADC input drivers, active filters, and precision instrumentation front-ends. In transimpedance applications, the combination of 0.92 nV/√Hz and 2.3 pA/√Hz noise is critical when the photodiode capacitance and feedback resistor push the noise optimum into this impedance window. When designing, keep feedback resistor values low to limit noise gain peaking, use a small feedback capacitor to stabilize the loop, and place supply-bypass capacitors within 2 mm of the V+ and V- pins. Output drive is rated to ±70 mA but sustained DC output current near this value will heat the SOIC-8 package quickly - derate or use the SOIC-8 EP variant for heavier loads. This page synthesizes distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet, giving engineers a one-stop specification and selection resource.

RFC Hubungi kami
LMP7721MA/NOPB - 3fA Bias Precision Op Amp 17MHz | TI
LMP7721MA/NOPB

LMP7721MA/NOPB - 3fA Bias Precision Op Amp 17MHz | TI

The Texas Instruments LMP7721MA/NOPB is a precision operational amplifier featuring the industry's lowest specified input bias current of 3 femtoamperes (fA), with guaranteed limits of ±20 fA at 25°C and ±900 fA at 85°C. It delivers a 17 MHz gain-bandwidth product, 12.8 V/µs slew rate, and rail-to-rail output swing from a supply of 1.8V to 5.5V (or ±0.9V to ±2.75V dual) in an 8-pin SOIC (D) package. An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output, used throughout analog signal conditioning, filtering, and instrumentation systems. The LMP7721 belongs to the precision amplifier family within linear integrated circuits; its distinguishing attribute, ultra-low input bias current, enables accurate measurement of tiny currents from very high-impedance sources such as electrochemical electrodes and photodiodes, which standard CMOS or bipolar op amps cannot resolve. Key features include 7.5 nV/√Hz input voltage noise, 84 dB open-loop gain, typical offset voltage of 26 µV, and input impedance of 10^13 Ω. A shutdown mode reduces supply current to 40 µA, supporting battery-operated designs. The device is specified over the extended industrial temperature range of -40°C to +125°C. Technically, the LMP7721 employs a CMOS input stage with bias-current cancellation to reach femtoampere input currents. Critically, its unique SOIC-8 pinout physically isolates the input pins (2 and 3) from the output (pin 6) and supply pins (4 and 7), preventing PCB leakage currents from corrupting the femtoampere-level input and enabling effective guard-ring routing. Typical applications include electrochemical sensors (pH, gas, and ion-selective electrodes), photodiode/transimpedance amplifiers, high-impedance buffers, and medical instrumentation such as glucose monitors and blood gas analyzers, where picoampere-level accuracy is mandatory. When designing with this device, implement guard rings around the input pins and clean, no-clean-free flux PCB practices to fully realize the 3 fA performance; otherwise board leakage, not the amplifier, will dominate input current error.

RFC Hubungi kami
LMP7721MA/NOPB-Q1 - 3fA Input Bias Precision Op Amp | Texas Instruments
LMP7721MA/NOPB

LMP7721MA/NOPB-Q1 - 3fA Input Bias Precision Op Amp | Texas Instruments

The LMP7721MA/NOPB is a single-channel precision operational amplifier from Texas Instruments featuring the industry's lowest guaranteed input bias current of 3 fA (typical), with a specified limit of plus/minus 20 fA at 25C and plus/minus 900 fA at 85C. It operates from a single 1.8V to 5.5V supply, delivers 17 MHz gain-bandwidth product, and 12.8 V/us slew rate in an 8-pin SOIC package. An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs, forming the foundation of analog signal conditioning within the amplifier IC hierarchy: operational amplifier -> precision amplifier -> analog front end -> signal chain IC. Precision amplifiers are distinguished by near-zero DC error terms - input bias current, offset voltage, and drift. The LMP7721 achieves its femtoampere-class input bias current through patent-pending input bias current cancellation circuitry, which maintains ultra-low bias current over temperature. Critically, the 8-pin SOIC uses a special pinout that isolates the amplifier inputs from the power supply and output pins. With proper board layout techniques, this unique pinout prevents PCB leakage current from reaching the input pins - a decisive advantage over conventional op amp pinouts when guarding is required. As a rail-to-rail input and output amplifier, it maximizes dynamic range in low-voltage systems while drawing low supply current, suiting battery-operated instruments. The wide supply range and high GBW allow use with electrochemical cells, photodiodes, and high-impedance sensors where even picoampere loading corrupts measurements. Typical applications include ionization chamber and electrochemical sensor front ends, photodiode transimpedance amplifiers for low-light detection, pH and dissolved-gas probe buffers, and picoammeter instrumentation. Design tip: to fully exploit the 3 fA bias current, use guard rings connected to the input-following low-impedance node and clean the PCB after assembly - flux residue and moisture can leak picoamperes that dwarf the amplifier's own bias current.

USD $5.90 Hubungi kami
LMP8350MA/NOPB - Ultra-Low Distortion ADC Driver | Texas Instruments
LMP8350MA/NOPB

LMP8350MA/NOPB - Ultra-Low Distortion ADC Driver | Texas Instruments

The Texas Instruments LMP8350MA/NOPB is an ultra-low-distortion fully-differential precision ADC driver designed for driving high-performance analog-to-digital converters in data acquisition systems. It ships in an 8-pin SOIC (D, 3.90 mm width) package with an operating temperature range of -40C to +85C and a RoHS-compliant lead-free finish. A fully-differential ADC driver is a special-purpose amplifier that converts a single-ended or differential input into a balanced differential output optimized for the differential input stage of precision ADCs. Within the signal-chain hierarchy (ADC driver -> amplifier -> analog front end -> signal chain), it provides output common-mode control, rejects even-order harmonics, and improves common-mode noise immunity ahead of the converter. Key features include ultra-low distortion across a fully-differential signal path and three selectable operating modes controlled by a unique mode enable pin. As part of TI's PowerWise family, the high power mode is optimized for highest AC dynamic performance, while lower modes trade dynamic range for reduced power consumption - a flexibility few fixed-power differential drivers offer. The /NOPB suffix denotes a no-pull BOM with lead-free, RoHS-compliant plating suitable for global commercial and industrial builds. Technically, the differential architecture inherently cancels common-mode noise and suppresses even-order distortion, which directly benefits THD and SNR when interfacing to precision SAR and delta-sigma converters. The three-mode design lets one footprint serve both battery-powered low-power data acquisition and high-AC-performance instrumentation, differentiating the LMP8350 from conventional fixed-bias fully-differential amplifiers. Typical applications include high-speed precision data acquisition, industrial process control and PLC analog input modules, medical ultrasound front ends, communications receivers and software-defined radios, automated test equipment, and portable battery-powered instruments. Design tip: realize the datasheet ultra-low-distortion performance only with a clean, symmetrical differential PCB layout, tight supply decoupling, and correct MODE pin configuration; verify pricing as of 2026-08-30 with current distributor stock at DigiKey and Mouser.

RFC Hubungi kami
LMP8350MA/NOPB-Q1 - Ultra-Low Distortion ADC Driver | TI
LMP8350MA/NOPB-Q1

LMP8350MA/NOPB-Q1 - Ultra-Low Distortion ADC Driver | TI

The Texas Instruments LMP8350MA/NOPB-Q1 is an ultra-low distortion fully-differential precision amplifier designed for driving high-performance analog-to-digital converters (ADCs). Packaged in an 8-pin SOIC (3.90 mm width), it belongs to TI's LMP precision amplifier family and the PowerWise product line, with an operating temperature range of -40C to +85C. Note: the verified web data covers the base LMP8350MA/NOPB; the -Q1 suffix variant should be confirmed against TI ordering information. A fully-differential amplifier (FDA) is a special-purpose amplifier that processes and outputs a differential signal, converting single-ended inputs to differential outputs with excellent common-mode rejection. FDAs are the preferred interface between single-ended analog sources and differential-input ADCs because they cancel common-mode noise, improve dynamic range, and maintain balance in the signal chain. The defining feature of the LMP8350 is its unique mode-enable pin, which lets the designer choose among three operating modes that trade power consumption for dynamic performance. The high-power mode is optimized for the highest AC performance and ultra-low distortion, while lower-power modes save current in battery-powered or thermally constrained systems. As an ADC driver for data acquisition, it achieves very low harmonic distortion suitable for driving precision and high-speed converters. According to the TI datasheet (LMP8350, 36-page document), the device is engineered for driving high-performance precision ADCs in data acquisition systems. Its differential architecture, selectable power modes, and precision DC performance make it a strong fit where signal integrity is paramount. Typical applications include precision data acquisition front ends, industrial process control, test and measurement instrumentation, and medical imaging signal chains - anywhere a single-ended or differential source must drive a differential ADC input without degrading THD or SNR. Design tip: the selected power mode affects both bandwidth and distortion, so verify THD at your target frequency and gain in the chosen mode, and keep the mode pin driven from a defined logic level for deterministic startup.

RFC Hubungi kami
LMP8640MK-H - 42V Current Sense Amp, 950kHz | Texas Instruments
LMP8640MK-H

LMP8640MK-H - 42V Current Sense Amp, 950kHz | Texas Instruments

The Texas Instruments LMP8640MK-H is a precision high-voltage current sense amplifier that detects small differential voltages across an external shunt resistor in the presence of high input common-mode voltages up to 42V, housed in a 6-pin SOT-23-THIN (TSOT-23-6, MK package). The device operates from a 2.7V to 12V supply and accepts common-mode inputs from -2V to 42V, with a unity-gain bandwidth of 950kHz and a slew rate of 1.8 V/us, enabling fast transient response in switching power-supply feedback loops. A current sense amplifier is a specialized analog IC that converts a small differential voltage developed across a low-value shunt resistor into a ground-referenced output proportional to load current. These devices sit in the signal-chain hierarchy between the power stage (MOSFET/IGBT switches) and the control stage (MCU/DSP/ADC), allowing tight closed-loop monitoring of motor, solenoid, and battery currents in industrial, automotive, and telecom systems. Compared with discrete op-amp current-sense solutions, integrated parts like the LMP8640 offer calibrated fixed gains, factory-trimmed offsets, and built-in EMI/RFI filtering that would otherwise consume board area and design effort. Key specifications include a fixed gain of 20 (the -H variant), input offset voltage in the sub-millivolt range, integrated EMI rejection on the input pins, and a low quiescent supply current suited to always-on monitoring. The TSOT-23-6 package provides a small 2.9 mm x 1.6 mm footprint suitable for high-density power-conversion PCBs. The wide -2V to 42V common-mode window makes the part tolerant of load-dump transients in 12V/24V automotive and industrial buses. The architecture uses a precision front-end differential pair followed by gain and output stages optimized for unidirectional or bidirectional current monitoring depending on the reference pin connection. The high 1.8 V/us slew rate preserves signal fidelity during rapid di/dt events such as inrush, PWM switching, and motor commutation. Integrated RFI filtering suppresses the high-frequency noise that would otherwise be rectified by the input stage and appear as DC error at the output. Typical applications include solenoid and valve current monitoring, motor-control phase current sensing, battery-pack charge/discurrent monitoring, 48V telecom rail current telemetry, and high-side current sensing in switching power supplies. The 42V common-mode range covers 12V/24V industrial buses with substantial transient headroom. When designing with this device, place the sense resistor close to the IC input pins and use a Kelvin connection to minimize parasitic resistance errors. The reference pin (REF) sets the output zero-current voltage; for unidirectional sensing tie REF to ground, for bidirectional sensing tie to mid-rail. Decouple VCC with a 100 nF ceramic capacitor placed within 5 mm of the supply pin. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and application-specific design guidance not consolidated on the manufacturer product page.

RFC Hubungi kami
LMP8640MK-H/NOPB - 42V Precision Current Sense Amplifier | TI
LMP8640MK-H/NOPB

LMP8640MK-H/NOPB - 42V Precision Current Sense Amplifier | TI

The Texas Instruments LMP8640MK-H/NOPB is a precision high-voltage current sense amplifier that detects small differential voltages across an external sense resistor in the presence of large common-mode voltages. Housed in a 6-pin SOT-23-THIN (TSOT-23-6, DDC) package, it operates from a 2.7V to 12V supply and accepts common-mode input voltages from -2V to +42V, making it ideal for high-side and low-side current monitoring in 12V, 24V, and 36V industrial buses. A current sense amplifier is an analog IC that amplifies the small differential voltage developed across a shunt resistor carrying the load current, while rejecting the large common-mode voltage present at the resistor terminals. This category sits within the broader hierarchy of operational amplifiers (op-amps) and instrumentation amplifiers, which in turn belong to the signal-conditioning family of analog ICs used in power management, motor control, and battery monitoring. The LMP8640MK-H/NOPB provides fixed internal gain (the "-H" variant specifies the gain version), eliminating the need for external gain-setting resistors and simplifying PCB layout. Key features include a -2V to +42V common-mode input range that survives load-dump transients in automotive and industrial systems, a fixed gain that improves noise immunity versus discrete op-amp solutions, and a 950 kHz gain-bandwidth product that supports fast transient response for current-mode control loops. The device also delivers 1.8 V/us slew rate, low offset, and integrated EMI filtering. The TSOT-23-6 package offers a compact 2.9 mm x 1.6 mm footprint with thermal performance suitable for industrial temperature ranges (-40C to +125C). The LMP8640MK-H/NOPB uses a precision chopper-stabilized input stage and thin-film resistor network to achieve low offset and high common-mode rejection ratio (CMRR). Its high PSRR ensures accurate current measurement even when the supply rail is noisy, which is critical in switched-mode power supply (SMPS) and motor-drive applications where large dv/dt events couple into the measurement node. Typical applications include high-side current sensing in telecom brick modules, battery-pack current monitoring in e-mobility and UPS systems, motor phase-current sensing in industrial drives, and precision load monitoring in solar inverters. The wide common-mode range also suits 48V telecom rails and 24V industrial automation backplanes. When designing with the LMP8640MK-H/NOPB, select a low-inductance Kelvin-connected sense resistor to avoid errors from PCB trace resistance, and place a 0.1 uF supply bypass capacitor as close to the IC as possible. The internal fixed gain eliminates gain-error calculations but the designer must still budget for sense-resistor tolerance and thermal drift. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFC Hubungi kami
LMP91000SD/NOPB - Configurable AFE Potentiostat for Chemical Sensing | TI
LMP91000SD/NOPB

LMP91000SD/NOPB - Configurable AFE Potentiostat for Chemical Sensing | TI

The Texas Instruments LMP91000SD/NOPB is a programmable analog front-end (AFE) designed for micro-power electrochemical sensing applications, integrating a complete signal path between a chemical sensor and a microcontroller. It provides 1 channel, 8-bit register interface, operates from a 2.7V to 5.25V analog and digital supply, and is housed in a 14-pin WSON (4 mm x 4 mm) package. According to the TI product page, the device generates an output voltage proportional to the cell current, making it a drop-in read sensor analog subsystem for portable gas detection. An analog front-end (AFE) for electrochemical sensors is a mixed-signal IC that combines a potentiostat (a controlled-voltage/current bias circuit for the sensor working electrode), a transimpedance amplifier (TIA) that converts the sensor's picoampere-level current into a usable voltage, and a digital interface for microcontroller configuration. The LMP91000 sits inside the broader sensor signal chain hierarchy: electrochemical sensor -> AFE/potentiostat -> ADC -> microcontroller. Its programmability enables it to support multiple electrochemical sensors including 3-lead toxic gas sensors and 2-lead galvanic cells. Key features of the LMP91000SD/NOPB include a fully programmable transimpedance amplifier (TIA) gain, programmable bias voltage for the working electrode, programmable load resistor for the reference electrode, and an integrated temperature sensor to compensate for sensor temperature drift. The device also integrates a configurable I2C-compatible serial interface. Its low quiescent current makes it suitable for battery-powered portable gas detectors, and its small 4 mm x 4 mm WSON-14 footprint enables dense PCB layouts in wearable multi-gas sensor modules. Technically, the LMP91000 implements a true potentiostat topology using an op-amp-based control loop with MOSFET output stages, allowing the working electrode potential to be held precisely at the programmed bias voltage while sourcing or sinking the cell current. The integrated 8-bit DAC sets the bias voltage in 1 mV-typical steps, and the TIA gain is programmed through internal feedback resistor selection, giving the designer flexibility to match sensors with different current ranges (nA-level toxic gas sensors to mA-level bio-sensors). Typical applications include portable toxic gas detectors (CO, H2S, NO2), industrial safety monitors, breath analyzers, blood glucose meters, and environmental air-quality monitors. In a portable gas detector, the LMP91000 is placed between the 3-lead electrochemical sensor and a low-power MCU with an integrated ADC; the AFE handles biasing and current-to-voltage conversion while the MCU samples the voltage and applies temperature compensation. When designing with the LMP91000, ensure that the VDD decoupling capacitors are placed as close as possible to the analog and digital supply pins, and that the working, counter, and reference electrode traces are guarded to prevent leakage. The I2C SDA/SCL lines require pull-up resistors to VDD; consult the manufacturer's datasheet for the recommended pull-up value based on bus capacitance and clock speed. This page synthesizes distributor pricing, drop-in alternatives, and design notes not aggregated in any one manufacturer data sheet.

RFC Hubungi kami
LMR321G-GTR - Low-Power Ground-Sense Op Amp | ROHM
LMR321G-GTR

LMR321G-GTR - Low-Power Ground-Sense Op Amp | ROHM

The ROHM LMR321G-GTR is a single-circuit, low-power, ground-sense general-purpose operational amplifier in a 5-pin SSOP package. It belongs to the LMR321, LMR358, and LMR324 family of low-voltage operational amplifiers designed for output full-swing operation. The device is intended for portable, industrial, instrumentation, sensor-interface, and low-voltage signal-conditioning applications where low supply-current consumption and operation from low supply voltages are important. An operational amplifier is an analog signal-processing IC that compares two input voltages and drives its output toward a level representing their difference. In a standard amplifier configuration, the feedback network determines the closed-loop gain, while the op-amp supplies high open-loop gain and signal amplification. The ground-sense configuration is particularly useful when the input signal is referenced to ground and the output must remain close to the ground rail. The LMR321G-GTR provides a single amplifier per package, simplifying designs that require only one active device. ROHM describes the LMR321G as a low-voltage, low-power general-purpose operational amplifier with full-swing output. These characteristics make it suitable for battery-powered equipment, current-sense conditioning, sensor interfaces, and low-voltage control systems. The single-channel configuration reduces package count when additional amplifier channels are not required. Its 5-SSOP format also supports compact PCB layouts when compared with larger multi-channel packages. The LMR321, LMR358, and LMR324 families provide single-, dual-, and quad-channel options in a related low-power product grouping. Engineers can therefore standardize on the LMR family while selecting the channel count that matches the circuit. The GTR ordering code identifies the single LMR321G device in a compact SSOP package with a tape-and-reel production configuration. Exact electrical limits, input/output ranges, current consumption, and stability requirements should be confirmed in the manufacturer datasheet before release to production. Typical uses include amplifying signals from low-voltage sensors, buffering analog inputs, conditioning shunt-monitor signals in portable instruments, and providing general-purpose amplification in embedded systems. The full-swing output capability can simplify signal-chain design when the load and bias conditions are compatible with the device's operating region. In precision measurement paths, input offset voltage, input bias current, noise, common-mode range, and output-drive capability remain the principal selection criteria. For layout, keep the feedback loop compact and connect the bypass capacitor close to the supply pins. Maintain the ground reference required by the amplifier circuit and avoid placing high-current return paths beneath sensitive analog signals. Confirm capacitive-load stability and output-current limits for the intended load. When replacing another five-pin amplifier, verify the package drawing, exposed-pad requirements, pin functions, supply range, common-mode range, and output-swing behavior rather than relying only on the package name. This product page combines the manufacturer's device identity with distributor listings, package information, application guidance, comparison fields, and practical design notes. It is intended to accelerate component selection and PCB planning while keeping the final engineering decision tied to the official LMR321G datasheet.

RFC Hubungi kami
LMR324F-GE2 - 4-Channel Low-Power Op Amp | ROHM
LMR324F-GE2

LMR324F-GE2 - 4-Channel Low-Power Op Amp | ROHM

The ROHM Semiconductor LMR324F-GE2 is a four-circuit, general-purpose operational amplifier with rail-to-rail output, low-power operation, and ground-sense capability in a 14-SOP package. It combines four independent amplifiers in one package for compact analog signal-conditioning designs. An operational amplifier, commonly called an op amp, is an active analog component that uses high gain and negative feedback to amplify the voltage difference between its two inputs. The LMR324 belongs to the low-dropout linear-amplifier hierarchy and the broader operational-amplifier semiconductor category. Its ground-sense architecture is intended for applications operating near the lower supply rail, while the full-swing output extends usable output range toward both supply limits. The primary features include four amplifier circuits per package, rail-to-rail output, low supply-current consumption, low-voltage operation, and a general-purpose signal path. These characteristics make the device useful where several low-level signals must be amplified, buffered, or conditioned without allocating a separate package to every channel. The quad configuration can also reduce board area and simplify power distribution compared with four discrete single amplifiers. Each channel is intended for conventional closed-loop operation with external feedback. The ground-sense input arrangement is especially relevant to portable measurement, sensor-interface, and low-voltage control circuits where signals may occupy the lower portion of the supply range. Because final offset, bandwidth, slew rate, common-mode range, and output-current limits determine practical performance, designers should consult the ROHM LMR324F datasheet before setting gain, loading, or bypassing values. Typical uses include low-voltage sensor conditioning, portable instrumentation, industrial control interfaces, battery-powered monitoring, and general-purpose audio or control-signal amplification. A four-channel implementation can provide independent amplification for bridge sensors, analog filters, level conversions within an analog domain, or small actuator-control loops. The same package can also implement repeated circuit blocks where matching and identical part characteristics simplify design review and maintenance. For a new design, pay particular attention to input common-mode range, output swing under load, stability with the selected feedback network, and decoupling requirements. Place supply bypass capacitors close to the device and route each ground reference carefully, especially when all four channels process signals from different sources. Confirm that the electrical limits support the intended supply voltage, source impedance, capacitive load, and ambient temperature. This product page combines the manufacturer product information, package identification, cross-reference findings, and practical engineering guidance. It helps engineers compare the LMR324F-GE2 with its documented alternatives while focusing on fit-for-purpose decisions rather than treating package similarity alone as proof of electrical equivalence.

RFC Hubungi kami
LMR341G-GTR - 2MHz Low-Power Ground-Sense Op Amp | ROHM
LMR341G-GTR

LMR341G-GTR - 2MHz Low-Power Ground-Sense Op Amp | ROHM

The ROHM Semiconductor LMR341G-GTR is a single CMOS operational amplifier designed for low-voltage, low-power ground-sense applications. It operates from 2.7 V to 5.5 V, provides a 2 MHz gain-bandwidth product and 1 V/µs slew rate, and is supplied in a 6-pin SSOP package. Its low 80 µA supply current, MOSFET input stage, shutdown function, and full-swing output make it suitable for battery-powered sensor and signal-conditioning systems. A ground-sense operational amplifier is a rail-to-rail-input-and-output amplifier optimized for measuring small voltages relative to ground. In the broader component hierarchy, it belongs to the operational-amplifier family, then to amplifier ICs and analog semiconductors. Its low-noise CMOS input stage provides low input bias current, while the full-swing output allows the amplifier to operate close to the positive or negative supply limits without requiring a separate output-bias arrangement. The LMR341G combines a 2 MHz gain-bandwidth product with a 1 V/µs slew rate in a low 2.7 V to 5.5 V supply range. Typical supply current is 80 µA, reducing power consumption in continuously powered equipment. The shutdown function provides a controlled low-power operating state, while the low-bias MOSFET input stage helps minimize source-current loading on high-impedance sensors. These characteristics are particularly useful when sensing battery voltage, resistive sensor outputs, or low-level analog signals. The amplifier is designed for general-purpose low-voltage analog signal conditioning. Its CMOS input stage supports low input bias current, and its output can swing fully across the supply range for improved measurement utilization. A 2 MHz bandwidth is adequate for sensor signals that do not require high-frequency signal processing, while the 1 V/µs slew rate allows the output to track moderate input steps without requiring a larger, higher-power package. Typical uses include battery monitoring, portable instrumentation, sensor-interface circuits, industrial control modules, and low-voltage data-acquisition systems. In a battery-powered design, the shutdown pin can reduce consumption when the measurement function is not required. For high-impedance sensor nodes, the low input bias current helps avoid input-voltage errors caused by leakage through source impedances. PCB implementation should keep the input and feedback components close to their corresponding pins, and the decoupling capacitor should be placed directly between the supply and ground pins. Because ground-sense accuracy depends on the reference plane, connect the sensor return and amplifier ground using a low-impedance layout. Avoid long input traces and unnecessary copper around high-impedance input nodes to reduce leakage and susceptibility to interference. This page combines the manufacturer’s device description, distributor identification, electrical characteristics, package information, sourcing guidance, and practical design considerations. It also identifies family-level drop-in candidates while clearly separating confirmed functions from parameters that require final datasheet and qualification review before a design is released to production.

RFC Hubungi kami
LMR342F-GE2 - Low-Power Rail-to-Rail CMOS Op Amp | ROHM
LMR342F-GE2

LMR342F-GE2 - Low-Power Rail-to-Rail CMOS Op Amp | ROHM

The ROHM LMR342F-GE2 is a low-supply-current CMOS operational amplifier intended for ground-sense signal conditioning, with a two-circuit configuration and an 8-SOP package. The LMR342F series is designed around low operating supply voltage, low supply current, low input bias current, input ground sensing, and full-swing output capability. These characteristics make it suitable for battery-powered equipment, sensor amplifiers, battery-monitoring circuits, and voice audio preamplifiers. The product is identified as a rail-to-Rail CMOS amplifier by ROHM and distributor product listings. A CMOS operational amplifier is a voltage-input, voltage-output amplifier whose internal devices consume very little bias current compared with conventional bipolar input stages. In the signal-chain hierarchy, the LMR342F-GE2 belongs to the operational amplifier family within analog and linear integrated circuits, where low input bias current helps preserve the integrity of high-impedance sensor signals. Its ground-sense architecture is particularly relevant when the input signal is referenced close to ground and the amplifier must support low-voltage operation. The key engineering benefits are low operating supply current, low input bias current, ground-sense inputs, and full-swing output behavior. The two-circuit configuration allows two independent amplifier channels in one package, reducing board area where a dual amplifier is required. The low-power operating characteristics also help conserve energy in portable systems, while the rail-to-Rail output can improve usable signal range in low-voltage designs. The manufacturer product page identifies sensor amplification, battery-powered electronic equipment, battery monitoring, and audio preamplification as representative use cases. The LMR342F family is implemented as a CMOS operational amplifier for precision and low-power signal conditioning. The exact electrical limits for the LMR342F-GE2, including supply range, gain-bandwidth product, input offset voltage, input bias current, output swing, and temperature limits, are not fully reproduced in the product excerpts available for this page. Use the manufacturer datasheet for the complete electrical characteristics, test conditions, recommended operating conditions, and pin-description table before finalizing a circuit. Typical designs include current-sense and battery-monitor front ends, low-voltage sensor signal conditioning, portable audio preamplification, and grounded sensor inputs. Because the amplifier is intended for low-voltage and low-power systems, check supply headroom and output swing against the required signal range. The ground-sense input arrangement can simplify sensing relative to ground, while the full-swing output helps maximize usable output range. For PCB implementation, place the device close to the protected sensor node and keep the input path short to minimize leakage and contamination sensitivity. Confirm bypass-capacitor requirements and stability guidance in the manufacturer datasheet. Decouple the supply rail locally and keep high-current return paths away from the input reference to reduce ground-induced errors. This product page combines manufacturer and distributor information with application guidance, selection criteria, package details, and verified drop-in alternatives. It is intended to accelerate engineering evaluation while directing final electrical, thermal, and qualification decisions to the applicable ROHM documentation.

RFC Hubungi kami
LMR344F-GE2 - Low-Power Quad CMOS Op Amp | ROHM
LMR344F-GE2

LMR344F-GE2 - Low-Power Quad CMOS Op Amp | ROHM

ROHM Semiconductor LMR344F-GE2 is a low-power, four-circuit CMOS operational amplifier with rail-to-rail input and output operation, optimized for 2.7 V to 5.5 V operation in a 14-pin SOP package. It combines low supply current, low input bias current, input ground sensing, and full-swing output capability for portable and low-voltage analog systems. A CMOS operational amplifier is a voltage-gain device used to amplify weak sensor, audio, or feedback signals while operating from a low-voltage supply. The LMR344F belongs to the operational-amplifier hierarchy, where it provides input-ground sensing and rail-to-rail signal handling for battery-powered equipment, monitoring circuits, and voice audio preamplifiers. Rail-to-rail operation helps preserve usable input and output range when the supply voltage is restricted. The LMR344F family is designed for low operating supply voltage, low supply current, and low input bias current. Its four amplifiers share a common 14-pin SOP package, reducing board area in designs that require multiple signal-conditioning channels. The input-ground-sensing architecture is especially useful when an input signal is referenced to ground rather than to the midpoint of the supply rails. Full-swing output operation allows the amplifier outputs to approach the available supply-rail limits under suitable load conditions. This behavior is valuable in low-voltage systems where signal headroom is limited. The exact bandwidth, slew rate, input offset, noise, and output-current limits should be confirmed against the manufacturer datasheet before defining the closed-loop gain, load, and stability target of a new design. Typical applications include current sensing, portable instrumentation, battery monitoring, sensor signal conditioning, and voice audio preamplification. Multiple amplifiers in one package can support gain stages, differential front ends, filters, output drivers, or active feedback networks when their individual input, output, common-mode, and stability requirements match. For PCB implementation, use the manufacturer pin-description table to assign inputs, outputs, supply rails, and any unused amplifier channels. Keep input and feedback routing short, connect decoupling capacitors close to the supply pins, and provide stable feedback around each amplifier. Verify operation across the complete supply range and load range rather than assuming rail-to-rail input and output alone guarantees usable bandwidth. This product page combines the manufacturer product information with practical device classification, application guidance, design notes, and a same-package alternative assessment. It is intended to help engineers identify the correct amplifier function, validate package compatibility, and plan a robust low-voltage analog implementation.

RFC Hubungi kami
LMR358F-GE2 - Dual Ground-Sense Op Amp | ROHM Semiconductor
LMR358F-GE2

LMR358F-GE2 - Dual Ground-Sense Op Amp | ROHM Semiconductor

The ROHM Semiconductor LMR358F-GE2 is a dual, ground-sense operational amplifier designed for low-voltage, low-power signal processing. It provides two amplifier channels with rail-to-rail output characteristics in an 8-pin SOP package. The LMR358F belongs to the LMR series of low-power general-purpose operational amplifiers intended for applications where low supply-current consumption, low-voltage operation, accurate sensing near ground, and full-swing output capability are important. An operational amplifier is an analog integrated circuit that compares an inverting input with a non-inverting input and amplifies the voltage difference between them. A ground-sense amplifier is designed to maintain useful input and output behavior near the lower supply rail, making it suitable for sensor signals, battery-powered systems, and low-voltage instrumentation. Within the broader semiconductor hierarchy, this device is a dual-channel operational amplifier, analog amplifier IC, and low-power voltage-feedback amplifier. The principal features of the LMR358F-GE2 are its dual-channel configuration, low-power operating concept, low-voltage supply capability, ground-sense positioning, rail-to-rail output, and ability to swing the output close to the supply rails. The 8-SOP package provides a compact surface-mount footprint for two independent amplifier channels. Its general-purpose positioning also makes it suitable for buffering, amplification, voltage comparison, and signal-conditioning functions rather than limiting it to one specialized measurement topology. The LMR358F family shares its operating concept with the single-channel LMR321 and the quad-channel LMR324. This family relationship provides a practical path for common amplifier functions across different channel counts. The two-channel LMR358F is appropriate when a board requires two amplifiers but does not need the four channels of a quad device. Its full-swing output behavior can simplify interface design when the available output headroom is limited by a low supply voltage. Typical applications include battery-powered sensor conditioning, portable measurement systems, low-voltage industrial interfaces, current-sense amplifiers, general-purpose buffers, and embedded control analog sections. The device can amplify sensor outputs close to ground while operating from a constrained supply, making it particularly useful when the signal of interest occupies only a small portion of the available supply range. It can also be used where two independent analog channels provide a simpler layout than duplicating discrete amplifiers. When designing around the LMR358F-GE2, verify the input common-mode range, output swing, supply voltage, input bias current, noise, offset voltage, and stability requirements against the manufacturer datasheet for the selected operating conditions. Place input and output components close to the relevant device pins, maintain the recommended bypass capacitance, and route feedback paths away from noisy or high-impedance input nodes. Confirm the exposed or exposed-pad details only if the exact mechanical drawing indicates an exposed pad. This product page combines the manufacturer classification, package and channel details, commercial sourcing path, and engineering guidance with a conservative drop-in replacement assessment. It distinguishes a verified same-footprint family alternative from broader LM358-type devices whose package, pin arrangement, or electrical ratings may not support a true drop-in replacement.

RFC Hubungi kami
LMR821G-GTR - Low-Power Ground-Sense Op Amp | ROHM
LMR821G-GTR

LMR821G-GTR - Low-Power Ground-Sense Op Amp | ROHM

The ROHM Semiconductor LMR821G-GTR is a single-circuit, low-power ground-sense operational amplifier designed for low-voltage and low-supply-current operation. It is packaged in a compact 5-SSOP enclosure, also identified as SC-74A or SOT-753, for space-constrained sensing and signal-conditioning circuits. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its differential inputs. A ground-sense amplifier is used where the measured signal is referenced close to ground, such as in current-shunt monitoring, low-side sensing, and portable instrumentation. This amplifier belongs to the broader operational amplifier, analog IC, and semiconductor hierarchies. The LMR821G-GTR is specifically identified by ROHM as a low-power ground-sense operational amplifier. Its single-amplifier configuration reduces board area and is suitable for designs that need one sensing channel rather than a dual or quad device. The low-voltage and low-supply-current positioning makes it relevant to compact, battery-powered, and low-energy measurement systems. The LMR821G product family emphasizes low-voltage operation and low supply current. These characteristics help reduce the energy required when the amplifier remains connected to a low-capacity power source. Exact input-voltage limits, output-current capability, offset voltage, noise, bandwidth, and open-loop gain should be taken from the ROHM LMR821G datasheet when setting circuit operating points. Typical uses include low-side current detection, portable sensor interfaces, battery monitoring, and low-voltage signal conditioning. In these applications, the amplifier boosts a small ground-referenced differential signal while adding only modest circuit overhead. Its 5-pin surface-mount package also supports compact layouts, although pad geometry and exposed thermal-pad details must be confirmed against the package drawing. Use the manufacturer pin-description table when assigning PCB tracks because the complete numbered pin list is not included in the product-page summary. Confirm input common-mode range, output swing, unity-gain stability, and recommended external components before finalizing a high-gain or precision design. This page combines the manufacturer product information, exact-MPN distributor records, package details, application guidance, and engineering selection notes in one searchable reference. It is intended to accelerate sourcing and initial circuit assessment, while final qualification should follow the complete ROHM datasheet and application circuits.

RFC Hubungi kami
LMR822F-GE2 - Dual 5.5MHz RRO Op Amp | ROHM Semiconductor
LMR822F-GE2

LMR822F-GE2 - Dual 5.5MHz RRO Op Amp | ROHM Semiconductor

ROHM Semiconductor LMR822F-GE2 is a dual, rail-to-rail output operational amplifier designed for low-voltage operation from 2.5 V to 5.5 V, with a gain-bandwidth product of 5.5 MHz and a slew rate of 2 V/us. The device is packaged in an 8-SOP and combines two amplifier channels in one package. Its rail-to-rail output, full-swing operating characteristics, low supply-current consumption, high voltage gain, and high slew rate make it suitable for compact analog signal chains. An operational amplifier is a voltage-feedback amplifier used to amplify, buffer, filter, or control analog signals. The LMR822F belongs to the general-purpose operational-amplifier family within analog ICs and the broader signal-conditioning hierarchy. In portable battery-powered equipment, a low-voltage dual amplifier can process two signals or implement a differential stage while reducing package count and board area compared with two single amplifiers. The LMR822F's 5.5 MHz gain-bandwidth product supports closed-loop operation at moderate signal frequencies, while its 2 V/us slew rate improves large-signal response. Rail-to-rail output operation allows the output to approach the available supply rails more closely than a conventional fixed-output amplifier, which is useful when signal headroom is limited. Low supply-current consumption further supports mobile and other battery-powered applications. The dual-channel architecture provides two amplifiers in one 8-SOP package. Each channel can be configured as an inverting amplifier, non-inverting amplifier, voltage follower, comparator-like interface, or active-filter stage, subject to the stability, common-mode, and output-swing limits in the manufacturer datasheet. This flexibility makes the device useful in active filters, sensor interfaces, touch-screen control, audio signal conditioning, and low-voltage industrial systems. Typical applications include portable audio input stages, resistive touch-sensing channels, buffered sensor outputs, active low-pass filters, and low-voltage industrial control boards. The 2.5 V minimum supply supports systems operating from a regulated 3.3 V rail, while the 5.5 V maximum supply accommodates 5 V analog rails. Engineers should confirm frequency, gain, output swing, input range, noise, and stability requirements for the intended configuration. For dependable implementation, keep input and feedback connections short, place compensation or filter components close to the relevant pins, and avoid operating the amplifier beyond its stated 2.5 V to 5.5 V supply range. Verify each channel independently because dual packages share common supply and ground connections. This product page combines the manufacturer's core operating specifications with application guidance, package information, sourcing support, and an engineering comparison of relevant alternatives. It helps designers identify whether the LMR822F-GE2's dual 5.5 MHz architecture is suitable before beginning PCB implementation.

RFC Hubungi kami
LMR824F-GE2 - Low-Power Rail-to-Rail Op Amp | ROHM
LMR824F-GE2

LMR824F-GE2 - Low-Power Rail-to-Rail Op Amp | ROHM

The ROHM Semiconductor LMR824F-GE2 is a low-voltage, low-current, full-swing operational amplifier containing four amplifier circuits in a 14-SOIC package. Each channel supports a 2.5 V to 5.5 V supply range, while the listed per-channel supply current is 26 mA and input bias current is 30 nA. Its rail-to-rail output swing and low-power operating characteristics suit mobile equipment, low-voltage analog systems, active filters, signal conditioning, instrumentation, and audio circuits. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LMR824F belongs to the broader operational-amplifier and signal-conditioning hierarchy, where four independent channels can implement buffering, gain stages, filters, transducers, and analog signal processing. The quad-amplifier arrangement reduces package count and simplifies common supply routing compared with four separate single-channel devices. The LMR824F family emphasizes low operating supply current, high voltage gain, high slew rate, and output full-swing capability. Its 2.5 V to 5.5 V supply range supports systems operating from a single low-voltage rail. The four-channel configuration is particularly useful when a design requires several matched functional stages, although matching performance between channels should be evaluated from the manufacturer datasheet when precision ratios, offsets, or drift are critical. ROHM describes the LMR824F as a low-voltage, low-current, full-swing operational amplifier with high voltage gain and high slew rate. Its output can approach the supply rails, making it useful in low-voltage circuits where conventional fixed-output amplifiers would leave insufficient signal headroom. Because the four amplifiers share one package, supply bypassing and package-level thermal considerations affect every channel, including channels that are lightly loaded. Typical uses include mobile-equipment signal chains, active analog filters, sensor interfaces, low-voltage audio paths, transducer amplifiers, and general-purpose instrumentation. In a mobile design, the amplifier can buffer sensors or amplify low-level signals while operating directly from a low-voltage rail. In an active-filter implementation, its output swing helps preserve filter amplitude, while the quad format can provide multiple filter or buffer stages with shared supply routing. When laying out the circuit, place the supply-decoupling capacitor close to the positive and ground pins and keep sensitive input traces away from switching nodes and high-current return paths. Confirm the required input common-mode range, output swing, load current, stability, and noise performance for the selected feedback network. The manufacturer datasheet should be used for the exact pin assignment, electrical limits, recommended application circuit, and compensation guidance. This page combines the LMR824F-GE2 product characteristics, commercial sourcing path, package information, application guidance, and design considerations in one engineering-focused reference. It is intended to help designers identify the correct amplifier function, plan a pin-compatible assembly strategy, and evaluate the LMR824F-GE2 for compact low-voltage analog systems.

RFC Hubungi kami
LMR931G-GTR - 5V Low-Power Rail-to-Rail Op Amp | ROHM
LMR931G-GTR

LMR931G-GTR - 5V Low-Power Rail-to-Rail Op Amp | ROHM

ROHM Semiconductor LMR931G-GTR is a single-channel, low-power operational amplifier characterized by rail-to-rail input and output operation and a 5 V supply. It is supplied in a 5-pin SSOP package with tape-and-reel ordering indicated by the GTR suffix. The device is positioned for compact, low-voltage analog signal-conditioning circuits where low supply current, wide input common-mode range, and full-swing output capability are important. An operational amplifier, or op amp, is an analog integrated circuit that uses high-gain differential amplification to buffer, amplify, or condition signals. The LMR931G belongs to the broader hierarchy of operational amplifier, analog IC, and semiconductor products. Rail-to-rail input operation allows signals to approach the supply rails, while rail-to-rail output operation gives the output stage greater voltage range than a conventional output stage. These characteristics are particularly useful in battery-powered equipment and low-voltage sensor systems where signal headroom is limited. ROHM describes the LMR931G family as a low-power, low-voltage, input/output full-swing operational amplifier. The verified product information identifies a single amplifier with one circuit, a 5 V nominal operating supply, and a 5-SSOP package. The family also includes single, dual, and quad configurations, allowing a system designer to standardize amplifier functions across channels without changing the basic low-power operating approach. Shutdown is specifically identified for the LMR981 and LMR982 family members rather than for the LMR931G. The LMR931G-GTR is suited to low-voltage sensor interfaces, portable measurement systems, signal buffers, audio and communication support circuits, industrial controls, and general-purpose analog amplification. Its low-power operating concept can reduce system burden in applications where the amplifier does not need to operate continuously at high speed. Rail-to-rail input behavior can simplify biasing around midpoint, while full-swing output improves signal utilization at low supply voltages. Designers should verify the electrical limits, common-mode range, output swing, stability requirements, and recommended external components in the ROHM datasheet before release. Decoupling capacitors should be placed close to the supply and ground pins, and feedback and compensation networks should preserve the intended closed-loop response. Input and output behavior must also be checked against source impedance, load impedance, and the operating voltage of the surrounding circuit. This page combines the verified ROHM product information with package, application, comparison, and design guidance focused on practical selection. It identifies the LMR931G-GTR as a low-power, rail-to-rail single op amp and separates confirmed catalog facts from electrical parameters that require confirmation from the manufacturer datasheet.

RFC Hubungi kami
LMR932F-GE2 - Dual 1.4MHz Low-Power Op Amp | ROHM
LMR932F-GE2

LMR932F-GE2 - Dual 1.4MHz Low-Power Op Amp | ROHM

The ROHM Semiconductor LMR932F-GE2 is a dual low-power operational amplifier with a 1.4 MHz gain-bandwidth product, a 0.35 V/µs slew rate, and a 1.8 V to 5 V supply-voltage range, housed in an 8-pin SOP package. Its rail-to-rail output and input/output full-swing architecture make it suitable for low-voltage signal conditioning, sensor interfaces, audio paths, and portable equipment. An operational amplifier, or op amp, is a high-gain analog building block that compares two input voltages and drives an output according to their difference. Within the power-management and signal-processing hierarchy, the LMR932F belongs to the operational-amplifier family, where low power consumption, low supply voltage, and rail-to-rail operation make it suitable for battery-powered and portable systems. Two amplifiers are integrated into one package, reducing board area while providing independent channels. The LMR932F-GE2 combines a 1.4 MHz gain-bandwidth product with low power consumption and a typical bias current of 35 nA. Its 0.35 V/µs slew rate supports small- and medium-signal bandwidth applications without requiring a high-speed amplifier. Rail-to-rail output operation helps preserve usable output range near the supply rails, while the 5.5 mV input-offset specification should be considered in precision DC applications. An 8-SOP surface-mount package supports compact, conventional PCB assembly. The ROHM LMR932F series is positioned for low-voltage operation and low supply current. The dual configuration allows common tasks such as sensor amplification, active filtering, buffering, and level shifting to be implemented in one package. Because the amplifier operates down to 1.8 V, it is useful in systems using a single low-voltage rail. Its 1.4 MHz bandwidth makes it more appropriate for general-purpose analog signals than for high-frequency precision instrumentation. Typical uses include portable sensor conditioning, low-voltage audio input stages, industrial control interfaces, battery-powered measurement systems, and general-purpose analog filtering. Two channels are useful when a design needs independent amplification for two sensors, a balanced signal path, or an active filter and buffer combination. The 8-SOP package also simplifies retrofitting and provides a straightforward alternative to larger dual-amplifier packages. Designers should maintain input and output common-mode limits across the full supply range and verify output swing into the intended load. Decoupling capacitors should be placed close to the supply pins, while sensitive input routing should minimize leakage and nearby switching-node coupling. For low-frequency precision work, input bias current, offset voltage, and noise must be evaluated together rather than relying on bandwidth alone. This page organizes the principal electrical and packaging characteristics, practical application guidance, comparison criteria, and sourcing information for engineers evaluating the LMR932F-GE2. It also distinguishes verified same-package replacements from related devices that use different package outlines.

RFC Hubungi kami
LMR934F-GE2 - Low-Power Quad Rail-to-Rail Op Amp | ROHM
LMR934F-GE2

LMR934F-GE2 - Low-Power Quad Rail-to-Rail Op Amp | ROHM

ROHM Semiconductor LMR934F-GE2 is a low-power, four-circuit, input-output full-swing operational amplifier in a 14-SOIC package. The device supports a 5 V supply and is designed for general-purpose applications requiring rail-to-rail output swing. Its quad-channel configuration integrates four amplifiers into one package, reducing board area compared with separate single-channel devices. The LMR934F-GE2 belongs to ROHM's LMR series of low-voltage, low-supply-current operational amplifiers intended for compact and power-conscious analog circuits. An operational amplifier is an active analog building block that compares two input voltages and amplifies their difference. A rail-to-rail output amplifier can approach its supply rails at the output, increasing usable output range in low-voltage systems. The input-output full-swing designation identifies this device as suitable for applications requiring low-voltage operation and broad output range. Within the integrated-circuit hierarchy, the LMR934F-GE2 is an operational amplifier, which belongs to the amplifier IC and analog signal-processing categories. The LMR934F-GE2 provides four amplifier channels in one 14-SOIC package. Its low-power operating approach is suitable for battery-powered and portable equipment where supply efficiency and compactness matter. The rail-to-rail output characteristic supports signal conditioning near the positive and negative limits of a 5 V supply, while the quad configuration can implement filters, buffers, sensor interfaces, or multiple independent gain stages. The manufacturer identifies the LMR934 family as operable with low voltage and low supply current. The integrated four-channel architecture simplifies PCB design by reducing the number of packages and external connections required for multiple amplifier functions. The 14-SOIC footprint supports conventional surface-mount assembly, while full-swing output behavior can improve signal utilization in low-headroom analog systems. Because the device is intended for general-purpose amplification, its suitability for precision instrumentation, audio, or sensor conditioning depends on the complete operating conditions and circuit configuration, including supply voltage, load, bandwidth, and stability requirements. Typical uses include four-channel sensor signal conditioning, low-voltage filtering, buffering, portable test equipment, audio preamplification, and general embedded analog interfaces. In a four-sensor system, all channels can share the same supply and decoupling structure, while independent amplifier sections handle different input signals. In portable equipment, the low-power nature of the LMR series supports compact implementations, although total current consumption depends on the selected device, load condition, operating mode, and external circuitry. Layout should place the supply bypass capacitor close to the device and minimize trace resistance between the capacitor and amplifier supply pins. Keep input and feedback routing short, maintain symmetry between differential inputs, and keep high-impedance input nodes away from switching nodes and digital return currents. Confirm output swing, noise, offset, bias current, stability, and input common-mode range against the manufacturer datasheet before fixing the external feedback network for a particular gain or load. This product page organizes the exact MPN, technical constraints, practical applications, design guidance, and qualified comparison information for engineers evaluating the LMR934F-GE2. It also distinguishes confirmed manufacturer and distributor attributes from parameters that require direct datasheet verification, helping procurement and design teams assess fit without relying on ambiguous family-level descriptions.

RFC Hubungi kami
LMR981G-GTR - Low-Power Rail-to-Rail Op Amp | ROHM
LMR981G-GTR

LMR981G-GTR - Low-Power Rail-to-Rail Op Amp | ROHM

The ROHM Semiconductor LMR981G-GTR is a single-circuit, low-power operational amplifier with rail-to-rail input and output capability, supplied in a 6-pin SSOP embossed tape-and-reel package. The device is designed for low-voltage systems that require an amplifier to operate close to both supply rails while keeping supply current low. Its general-purpose configuration makes it applicable to sensor buffering, audio signal conditioning, low-voltage filtering, and general analog signal amplification. An operational amplifier, or op amp, is an analog integrated circuit that provides high voltage gain in an open-loop configuration. Rail-to-rail input and output amplifiers can accept input signals close to the negative and positive supply rails and can swing their output close to those rails. This capability is useful in low-voltage systems because it expands the usable input and output range without requiring a separate midrail bias reference. The LMR981G belongs to the ROHM LMR series of low-power input-output full-swing operational amplifiers. According to the manufacturer product page, this series was developed for single, dual, and quad amplifier configurations that operate at low voltage and low supply current. The LMR981G is the single-amplifier configuration, while the LMR982 family adds a shutdown function. Its 5 V supply rating, 6-pin SSOP package, and rail-to-rail input/output architecture make it a compact choice for portable and embedded analog designs. Key electrical characteristics include one amplifier circuit per package, general-purpose signal conditioning, low-power operation, and full-swing input and output behavior. The datasheet defines the detailed input bias current, input offset voltage, unity-gain bandwidth, slew rate, noise specifications, and output-current limits for design calculations. Because this page does not reproduce those numeric ratings, engineers should use the manufacturer datasheet for precision AC and DC design work. Typical applications include conditioning the output of resistive sensors, buffering ADC inputs, implementing active filters, and amplifying low-level analog waveforms from portable instruments. The SSOP-6 package is also useful where board space is restricted, although its small body and limited copper area require attention to thermal rise when the amplifier operates continuously near its output-current limit. When designing around the LMR981G-GTR, confirm the exact input common-mode range, output swing, unity-gain bandwidth, and noise figures for the selected supply voltage. Place the bypass capacitor close to the supply pin, keep feedback resistors close to the amplifier inputs, and avoid driving a capacitive load directly unless the stability behavior has been verified. This page combines the manufacturer product information with a practical selection guide, packaging details, design cautions, and a structured comparison of drop-in candidates. It adds engineering context around the LMR981G-GTR without replacing the manufacturer datasheet for guaranteed limits, test conditions, and absolute maximum ratings.

RFC Hubungi kami
LMV321IDBVR - 1-MHz RRO Op Amp Single 5.5V | Texas Instruments
LMV321IDBVR

LMV321IDBVR - 1-MHz RRO Op Amp Single 5.5V | Texas Instruments

The Texas Instruments LMV321IDBVR is a single-channel, low-voltage, rail-to-rail output CMOS operational amplifier in a 5-pin SOT-23 (DBV) package. It operates from a single supply of 2.7 V to 5.5 V (5 V performance characterized), delivers a unity-gain bandwidth of 1 MHz, and offers rail-to-rail output swing from a low 130 µA typical supply current. The part is qualified for -40 °C to +125 °C operation and is offered on 3000-piece tape-and-reel. A rail-to-rail output (RRO) op amp is a linear amplifier whose output voltage can swing to within tens of millivolts of either supply rail, maximizing dynamic range in low-voltage single-supply systems. Compared with general-purpose amplifiers that lose 1 V to 2 V of headroom on each side, an RRO part lets the designer use the full ADC input range on a 3.3 V or 5 V rail. The LMV321 belongs to the broader family of CMOS operational amplifiers, a category of analog ICs that trades the lower noise of bipolar parts for very low quiescent current and single-supply operation. Key features include 1 MHz gain bandwidth product, 130 µA typical quiescent current, no output phase reversal, low crossover distortion, and an industry-standard 5-pin SOT-23 footprint. An internal ESD clamp and EMI filtering are characteristics of the larger LMV321A family; the original LMV321 line is recommended for cost-sensitive designs where these features are not required. The device is unity-gain stable and drives 2 kΩ loads comfortably at 5 V. The LMV321 is built on a CMOS process with a differential input pair and a rail-to-rail class-AB output stage, which keeps crossover distortion low compared to single-ended class-A CMOS outputs. The PSRR is specified at 50 dB at 1 kHz, and the input common-mode range extends from the negative rail to within 1.2 V of the positive rail — adequate for single-supply sensor buffers and instrumentation front-ends. Typical applications include single-supply sensor signal conditioning, current-sensing shunts in portable battery packs, low-side current monitors, headphone line drivers, and 5 V active filters. The part is widely used as a buffer/amplifier stage between photodiodes, thermistors, or strain gauges and downstream ADCs in IoT nodes. When designing with this device, place a 1 nF to 10 nF decoupling capacitor within 2 mm of the VCC pin and keep input trace lengths short to limit leakage-induced offsets. For driving heavy loads or large capacitive loads, add a 50 Ω to 100 Ω series resistor at the output to prevent oscillation. This page synthesizes distributor pricing, drop-in same-footprint alternatives, and practical design notes not found in the manufacturer datasheet.

RFC Hubungi kami
LMV321ILT - Single Low-Power Op Amp | STMicroelectronics
LMV321ILT

LMV321ILT - Single Low-Power Op Amp | STMicroelectronics

The LMV321ILT is a single, low-power, general-purpose operational amplifier from STMicroelectronics, offered in the compact SOT-23-5 package. It operates from a supply voltage range of 2.7V to 5.5V, making it suitable for battery-powered and portable applications. The device features a typical supply current of 130 µA, a gain-bandwidth product of 1.3 MHz, and an input offset voltage of 1 mV (max). Data verified as of 2026-08-05. An operational amplifier (op-amp) is a high-gain voltage amplifier with differential inputs and a single-ended output. It is a fundamental building block in analog electronics, used in signal conditioning, filtering, and amplification. In the hierarchy of electronic components, an op-amp falls under linear ICs, which are part of the broader category of analog integrated circuits. The LMV321ILT is a low-power variant, optimized for applications where power consumption is critical, such as battery-operated devices. Key features of the LMV321ILT include rail-to-rail input and output stages, which allow the output to swing close to the supply rails, maximizing dynamic range in low-voltage applications. The device also offers a wide operating temperature range of -40°C to +125°C, ensuring reliability in harsh environments. Its low supply current of 130 µA (typical) extends battery life in portable electronics. The LMV321ILT is built on a CMOS process, providing high input impedance and low input bias current. This makes it suitable for interfacing with high-impedance sensors and transducers. The device is unity-gain stable, simplifying design in buffer and follower configurations. Its small SOT-23-5 package is ideal for space-constrained PCB layouts. Typical applications include portable instrumentation, battery-powered signal conditioning, sensor interfaces, and active filters. In portable medical devices, the low power consumption and small footprint are critical. In sensor signal conditioning, the rail-to-rail output ensures maximum signal swing for ADC interfacing. When designing with the LMV321ILT, ensure proper decoupling of the power supply with a 0.1 µF ceramic capacitor placed close to the V+ pin. The input common-mode voltage range includes ground, allowing single-supply operation with ground-referenced inputs. Avoid exceeding the absolute maximum supply voltage of 6V to prevent damage. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the STMicroelectronics datasheet, providing a comprehensive resource for engineers evaluating the LMV321ILT.

USD $0.12 Hubungi kami
LMV331QDBVRQ1 - AEC-Q100 Single Comparator, Open-Collector, SOT-23-5 | TI
LMV331QDBVRQ1

LMV331QDBVRQ1 - AEC-Q100 Single Comparator, Open-Collector, SOT-23-5 | TI

The Texas Instruments LMV331QDBVRQ1 is an automotive-qualified (AEC-Q100) single-channel general-purpose low-voltage analog comparator housed in a 5-pin SOT-23 (DBV) package. It operates from a single 2.7 V to 5.5 V supply, draws a typical quiescent current of 60 µA, and provides a propagation delay of 600 ns with an open-collector output that supports wire-ORed configurations and easy level shifting. What is a comparator? A comparator is an analog integrated circuit that compares two input voltages and drives its output to a logic level indicating which input is larger. The LMV331-Q1 belongs to the analog comparator family within the broader signal-conditioning and power-management hierarchy, occupying the same role in the IC taxonomy as op-amps, references, and timers. Comparators are essential building blocks in voltage monitoring, threshold detection, zero-crossing detectors, and oscillator/waveform-shaping circuits. Key specifications of the LMV331QDBVRQ1 include an input common-mode voltage range that includes ground, low output saturation voltage, push-pull compatible open-collector output stage, and an operating temperature range of -40 °C to +125 °C (automotive Grade 1). The part is offered in the SC-74A / SOT-753 / SOT-23-5 footprint, making it one of the smallest qualified comparators available for space-constrained automotive modules. Internally, the LMV331 uses a PNP input stage and a low-voltage CMOS-compatible architecture that allows operation down to 2.7 V while maintaining a ground-referenced input range. The open-collector output requires an external pull-up resistor, which gives designers the freedom to level-shift the output to a voltage higher than the supply rail (for example, driving a 3.3 V logic output from a 5 V supply comparator) or to combine multiple comparator outputs on a single bus. Typical applications include automotive body controllers, battery management threshold detectors, sensor signal conditioning, window comparators, and oscillator circuits. The wide supply range and low quiescent current also suit portable consumer products, IoT battery-powered nodes, and industrial control systems requiring automotive-grade reliability. When designing with this part, choose the pull-up resistor value to balance switching speed and power dissipation. Avoid placing large capacitive loads directly on the open-collector output; use a small series resistor if capacitive loading cannot be avoided to limit inrush current during saturation-to-release transitions. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers source and apply the LMV331QDBVRQ1 efficiently.

RFC Hubungi kami