Produk (46,000+)

LTC2122IUK - Dual 14-Bit 170Msps ADC w/ JESD204B | ADI
LTC2122IUK

LTC2122IUK - Dual 14-Bit 170Msps ADC w/ JESD204B | ADI

The Analog Devices LTC2122IUK is a dual-channel, simultaneously-sampling 14-bit 170 Msps analog-to-digital converter (ADC) with JESD204B serial outputs, housed in a 48-lead QFN (7x7 mm) package with exposed pad. According to the LTC2122 datasheet, the converter delivers 70 dBFS SNR and 90 dBFS spurious-free dynamic range (SFDR) while supporting 1.25 GHz analog input bandwidth for IF/RF undersampling. The device operates from a 1.7V to 1.9V analog supply and integrates an on-chip clock-duty-cycle stabilizer, reducing external PLL requirements for high-speed communication systems. Each channel features a differential input front-end with 600 MHz full-power bandwidth, supporting wideband signal chains from DC to beyond 200 MHz of input frequency. A pipelined ADC architecture uses a high-speed, multi-stage switched-capacitor structure with digital error correction, allowing the LTC2122 to maintain 14-bit linearity up to 170 Msps. Dual-channel simultaneous sampling eliminates inter-channel skew, critical for MIMO receivers, phased-array radar, and diversity antenna systems. The JESD204B serial interface transports the digitized data using up to 4 lanes with 8b/10b encoding, deterministic latency, and embedded clock recovery, which minimizes board routing complexity compared to LVDS parallel interfaces. An on-chip SYSREF input supports deterministic latency for multi-device synchronization in large-channel-count systems. The LTC2122 targets demanding communications applications including LTE and multi-carrier GSM base-station receivers, software-defined radio, cable infrastructure head-end digitization, and high-density MIMO systems. Its 70 dBFS SNR and 90 dBFS SFDR at 170 Msps enable the receiver to digitize a 60 MHz LTE carrier with margin for adjacent-channel blocker rejection. The 1.25 GHz input bandwidth also supports undersampling of L-band and S-band signals, reducing the number of downconversion stages in the signal chain. The 48-QFN (7x7) exposed-pad package provides a low thermal resistance path, allowing operation across the industrial -40C to +85C temperature range without derating at the rated sample rate. For PCB layout, place 0.1uF and 10nF ceramic decoupling capacitors within 5 mm of each supply pin, with the exposed pad soldered to a continuous ground plane. Route the JESD204B serialized lanes as length-matched 100 ohm differential pairs with controlled 50 ohm single-ended impedance, and keep AC-coupled capacitors within 5 mm of the transmitter pins to meet the JESD204B eye-mask specification.

RFC Hubungi kami
LTC2123CUK - 14-Bit 250Msps Dual ADC, JESD204B | ADI
LTC2123CUK

LTC2123CUK - 14-Bit 250Msps Dual ADC, JESD204B | ADI

The Analog Devices LTC2123CUK is a dual-channel, simultaneous-sampling 14-bit, 250 Msps analog-to-digital converter with JESD204B serial outputs, housed in a 48-pin QFN (7x7 mm) package. It is designed for digitizing high-frequency, wide dynamic range signals and is targeted at demanding communications, radar, and test-and-measurement receivers. According to the Analog Devices LTC2123 datasheet, the converter delivers 70 dBFS SNR and 90 dBFS spurious-free dynamic range (SFDR) with a 1.25 GHz input bandwidth that supports accurate IF under-sampling. A pipelined ADC is a multi-stage converter that uses low-resolution flash sub-ADCs and a digital correction network to digitize an analog signal at very high sample rates while maintaining fine amplitude resolution. Within the broader converter taxonomy, pipelined ADCs sit between high-speed flash ADCs and lower-power successive-approximation ADCs, and they are the most widely used architecture for sampling rates from ~50 Msps to several hundred Msps. The LTC2123CUK belongs to this high-speed pipelined class and is positioned for multi-lane serial-data transport via the JEDEC-standardized JESD204B serial interface. Key features include a 14-bit resolution with 250 Msps sample rate, dual simultaneously-sampling analog inputs, an integrated clock and sample-and-hold front end, a 1.25 GHz analog input bandwidth, and a JESD204B-encoded serial data interface that minimizes board-routing complexity. The device operates from standard 1.8 V supply rails and includes internal dithering to improve low-amplitude linearity for small-signal RF work. The LTC2123CUK architecture uses a multi-stage switched-capacitor pipeline with proprietary calibration that flattens the noise and linearity curves across the Nyquist band. By running at 250 Msps from a single 1.8 V supply, the part achieves an SNR floor (70 dBFS) and SFDR (90 dBFS) that previously required dual-supply 5 V parts. The JESD204B Subclass 1 output supports deterministic latency and up to 4 lanes, which simplifies FPGA/ASIC capture when multiple converters must be phase-coherent. Typical applications include multi-antenna diversity receivers, IF digitizers for wireless base stations, broadband instrumentation, phased-array radar signal chains, and high-speed data acquisition test systems. The wide input bandwidth allows straightforward sampling of intermediate frequencies in the second or third Nyquist zone. When designing with the LTC2123CUK, plan the PCB layout for 50 ohm controlled-impedance analog inputs and tightly decouple the two 1.8 V supply domains (analog AVDD and digital DVDD/DRVDD) close to the package. The exposed thermal pad must be soldered to a continuous ground island to keep junction temperature within the commercial 0 to 70 C operating range. This page synthesizes distributor pricing, drop-in compatible variants from the same LTC2123 family, application context, and practical design notes not collected in any single manufacturer document.

RFC Hubungi kami
LTC2123IUK - 14-Bit 250Msps Dual ADC w/ JESD204B | ADI
LTC2123IUK

LTC2123IUK - 14-Bit 250Msps Dual ADC w/ JESD204B | ADI

The Analog Devices (formerly Linear Technology) LTC2123IUK is a dual 14-bit, 250 Msps analog-to-digital converter with JESD204B serial outputs, housed in a 48-lead QFN (7 mm x 7 mm) package with exposed pad. It is built on a high-performance pipelined architecture and provides two simultaneously-sampling ADC channels on a single die, supporting communications-grade signal chain designs. The listed 1ku price starts at $177.20 per part per the Analog Devices product page. An ADC (Analog-to-Digital Converter) is a mixed-signal data converter IC that samples continuous analog voltages and emits a discrete digital code for downstream processing. High-speed pipelined ADCs are positioned at the top of the converter hierarchy and serve as the gateway between RF/IF analog front-ends and FPGA/DSP digital processing in the signal chain - they are essential for software-defined radio, multi-antenna base stations, and electronic test & measurement instrumentation. Key features of the LTC2123 family include 14-bit resolution, 250 Msps sampling per channel, dual-channel simultaneous sampling, JESD204B serial output protocol for high-speed board-level data transfer, low-jitter clock input, internal dither for spurious-tone improvement, and selectable digital output modes. The 48-QFN package exposes a thermal pad for low-theta-JA board cooling and is qualified for the -40C to +85C industrial temperature range. The pipelined architecture distributes the conversion across cascaded low-resolution stages with redundant bit alignment, achieving high throughput at moderate power per channel while maintaining excellent AC linearity (SFDR, SNR). The integrated JESD204B interface replaces wide parallel LVDS buses with a serialized lane pair, dramatically simplifying FPGA-ADC board routing and improving multi-board synchronization via deterministic latency. Typical applications include LTE/4G/5G base-station receivers, multi-carrier software-defined radio, phased-array radar and EW systems, high-density MIMO digitizers, automated test equipment digitizer cards, and medical imaging front-ends. In all of these, the LTC2123's simultaneous dual-channel 250 Msps operation delivers the per-channel throughput required for direct IF sampling. When designing with this device, allocate a low-noise PLL clock source (e.g., ADF4350/ADF4106), maintain 100-ohm differential input impedance via tight-edad interface, and lay out the JESD204B lanes at length-matched controlled impedance per the JEDEC JESD204B specification to meet the required signal-integrity eye at the receiver. Verify with the manufacturer's evaluation kit (DC2154 or similar) before production.

RFC Hubungi kami
LTC2140CUP-12 - 12-Bit 25Msps Dual-Channel ADC | Analog Devices
LTC2140CUP-12

LTC2140CUP-12 - 12-Bit 25Msps Dual-Channel ADC | Analog Devices

The Analog Devices LTC2140CUP-12 is a 2-channel simultaneous-sampling 12-bit analog-to-digital converter (ADC) designed for digitizing high-frequency, wide-dynamic-range signals, supporting up to 25 Msps per channel in a 64-pin QFN (9 mm x 9 mm) package. It belongs to the LTC2142-12 / LTC2141-12 / LTC2140-12 family, which share a common datasheet and differ primarily in maximum sampling rate (65/40/25 Msps respectively), enabling software-compatible scaling across pipelined ADC designs. An ADC (Analog-to-Digital Converter) is a semiconductor device that samples a continuous analog voltage and converts it to a discrete digital code. In the system hierarchy, an ADC sits between an analog front-end (amplifiers, filters, sensors) and a digital signal processor (DSP, FPGA, or microcontroller). Pipelined ADCs such as the LTC2140CUP-12 use a multi-stage architecture that achieves high sample rates with moderate power consumption by interleaving low-resolution stages, trading slightly higher latency for the ability to capture multi-MHz bandwidth signals at low cost. Key features of the LTC2140CUP-12 include 12-bit resolution, 25 Msps per-channel sample rate, two simultaneously sampled differential or single-ended inputs, a wide input bandwidth, and CMOS or DDR LVDS digital output modes programmable via either a parallel or simple serial interface. The integrated input common-mode buffer and optional digital output randomization further simplify high-performance signal-chain design. Technically, the part uses a multi-stage pipelined architecture with on-chip sample-and-hold, an internal voltage reference, and a digitally programmable gain. The 64-pin QFN package with exposed pad keeps the loop area compact, which is critical at 25 Msps where clock and input edge rates sit near 100 ps. Programmable output modes and configurable full-scale range allow the ADC to interface directly to FPGAs, ASICs, or standard microcontrollers. Typical applications for the LTC2140CUP-12 include wireless base-station receiver IF digitizers, handheld signal analyzers, portable imaging systems, ultrasound front ends, and multi-carrier software-defined radio (SDR) platforms. The combination of low power consumption and dual channels makes it particularly attractive for portable and battery-powered test equipment requiring two synchronized acquisition paths. When designing with this ADC, pay close attention to analog input network layout, decoupling of the internal reference, and the length-matched output routing for DDR LVDS modes. Operating modes are configured through either a parallel CMOS or a simple SPI-style serial interface, allowing all available modes—including output format, gain, and channel selection—to be programmed in-system. This page synthesizes distributor pricing, drop-in alternatives, parameter-by-parameter comparisons, and practical PCB-level design notes not found in the manufacturer datasheet alone.

RFC Hubungi kami
LTC2140IUP-14 - 14-Bit 25Msps Dual ADC | Analog Devices | 64-QFN
LTC2140IUP-14

LTC2140IUP-14 - 14-Bit 25Msps Dual ADC | Analog Devices | 64-QFN

The Analog Devices LTC2140IUP-14 is a 14-bit, 25 Msps low-power dual-channel simultaneous-sampling pipelined analog-to-digital converter housed in a 64-lead QFN (9x9 mm) package with exposed pad. It integrates two matched ADC channels, each achieving ±1 LSB INL (typical) and ±0.3 LSB DNL (typical) with no missing codes over temperature, plus 1.2 LSBRMS transition noise for clean dynamic range. A pipelined ADC is a high-speed converter architecture that resolves one or two bits per internal stage and combines a sample-and-hold front end with multi-stage switched-capacitor gain/flash blocks; it is the workhorse architecture for communications baseband, ultrasound beamforming, and digital oscilloscope digitizers where multi-Msps rates are required. The LTC2140 sits in the broader hierarchy: ADC -> data converter -> signal chain IC -> mixed-signal semiconductor. Compared with successive-approximation (SAR) ADCs, pipelined parts deliver far higher sample rates at the cost of pipeline latency, while still offering multi-bit-per-stage quantization. Key features include a flexible digital output interface supporting full-rate CMOS, double-data-rate CMOS, or double-data-rate LVDS modes, and a separate output supply rail that lets the CMOS swing range from 0.4V to 1.8V independent of the analog 1.8V core. Programmable operating modes are accessible through either a parallel interface or a more flexible serial interface. The two channels sample simultaneously, which is essential for I/Q demodulators, phased-array receivers, and multi-channel data acquisition systems. Typical applications span communications infrastructure (IF/RF digitizers, diversity receivers, multi-antenna baseband), portable and battery-powered imaging, medical ultrasound front ends, industrial inspection cameras, and handheld or bench-top test instrumentation. Two matching channels let the part replace a dual-board ADC+amplifier chain in space-constrained designs. When designing with this part, allocate adequate copper area to the exposed pad for thermal relief (the dual 25 Msps core dissipates non-trivial power at full rate), route the LVDS/CMOS outputs with controlled impedance, and decouple OVDD and AVDD separately. The serial programming interface is recommended when the full feature set (output mode, gain, channel calibration) is required. This page synthesizes distributor stock and pricing, drop-in and same-package alternatives, and practical design notes that are not duplicated on the Analog Devices datasheet.

RFC Hubungi kami
LTC2141CUP-14 - 14-Bit 40Msps Dual ADC, 64-QFN | Analog Devices
LTC2141CUP-14

LTC2141CUP-14 - 14-Bit 40Msps Dual ADC, 64-QFN | Analog Devices

The Analog Devices LTC2141CUP-14 is a 14-bit, 40 Msps low-power dual analog-to-digital converter (ADC) housed in a 64-lead QFN (UP) package measuring 9x9 mm. Each ADC channel features ±1 LSB INL (typical), ±0.3 LSB DNL (typical), no missing codes over the operating temperature range, and 1.2 LSB RMS transition noise, providing true 14-bit linearity for demanding signal-chain designs. A separate output power supply allows the CMOS output swing to range from 1.2 V to 1.8 V, simplifying interface to modern FPGAs and ASICs. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that converts continuous analog voltages into discrete digital codes at a specified sampling rate. Dual ADCs integrate two synchronized sample-and-hold front ends and two pipelined conversion cores on a single die, enabling simultaneous sampling of two analog channels with matched gain, offset, and aperture delay. They sit within the broader hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor. The pipelined architecture used in the LTC2141-14 family balances high sample rate (tens to hundreds of Msps) with low power consumption, making it the dominant choice for communications, imaging, and instrumentation front ends. Key features of the LTC2141CUP-14 include a choice of full-rate CMOS, double-data-rate CMOS, or double-data-rate LVDS digital outputs for trade-offs between pin count, board area, and EMI immunity. The device supports both differential and single-ended analog inputs, accepts parallel or serial programming through a simple SPI-like interface, and operates from a single 1.8 V supply. Low power consumption and excellent AC performance (high SNR and SFDR) make it equally suitable for portable, multi-channel data acquisition systems and for dense baseband capture in communications infrastructure. Typical applications include multi-channel communications receivers, portable and battery-powered instrumentation, medical imaging front ends, radar signal processing, and general-purpose high-speed data acquisition. When designing with this part, observe the recommended input common-mode voltage and drive the analog inputs through a wideband transformer or low-noise op-amp driver to preserve SFDR; insufficient analog input bandwidth is the most common root cause of degraded ENOB in pipelined ADC designs.

RFC Hubungi kami
LTC2141IUP-12 - 12-Bit 40Msps Dual ADC | Analog Devices | 64-QFN
LTC2141IUP-12

LTC2141IUP-12 - 12-Bit 40Msps Dual ADC | Analog Devices | 64-QFN

The Analog Devices LTC2141IUP-12 is a 12-bit, 40 Msps, low-power dual-channel pipelined analog-to-digital converter (ADC) housed in a 64-lead QFN (9x9 mm) exposed-pad package with an industrial -40C to +85C operating temperature range (the "IUP" suffix designates industrial grade). Each of its two simultaneously sampling ADCs features a 12-bit resolution and is designed to digitize high-frequency, wide-dynamic-range signals with excellent spurious-free dynamic range. The device accepts differential or single-ended analog inputs and includes internal references plus an option for an external reference, allowing designers to trade off input range, noise and DC accuracy per channel. According to the manufacturer product page, the LTC2141-12 family lists at a 1ku starting price of $18.78 per part. What is a pipelined ADC? A pipelined analog-to-digital converter is a high-speed successive-approximation architecture that digitizes analog signals by dividing the conversion into multiple low-resolution stages, each driving a flash sub-ADC and a residue that is amplified and passed to the next stage. The pipelined topology sits within the broader hierarchy of data converters (ADC -> Nyquist ADC -> pipelined ADC -> mixed-signal IC) and is the dominant choice for sample rates from roughly 5 Msps to 200 Msps where both high throughput and low power are required - for example in wireless baseband, medical imaging and defense signal-intelligence receivers. Because the LTC2141-12 contains two matched ADCs sharing one clock, it doubles the channel density of a single 64-QFN footprint relative to two discrete single-channel parts. Key features of the LTC2141IUP-12 include 12-bit resolution, 40 Msps sampling rate, two simultaneously sampled differential input channels, selectable internal/external reference, low power dissipation for the speed class, CMOS-compatible outputs, and an exposed thermal pad that provides a low-theta-JA path for the heat generated by the two converters. The pipelined architecture calibrates its sub-ADC inter-stage gain and offset on-chip, eliminating user calibration and reducing time-to-design. The wide input bandwidth supports undersampling of IF signals, which makes the device attractive in communications receivers that digitize an IF directly rather than first down-converting to baseband. Architecturally, the LTC2141IUP-12 uses a multi-stage switched-capacitor pipeline per channel with proprietary linearization that minimizes integral non-linearity (INL) and differential non-linearity (DNL) at the 12-bit level. Each channel integrates its own sample-and-hold, ensuring matched timing between the two ADCs at the same applied clock edge, which is essential for I/Q demodulation and any diversity or beamforming receiver where the phase relationship between channels must be preserved. The 64-QFN (9x9) exposed-pad package also acts as the primary thermal relief path; PCB design must solder the EP to a continuous ground copper pour to achieve the rated thermal performance. Typical applications for the LTC2141IUP-12 include multi-carrier cellular base-station receivers, software-defined radio (SDR) front-ends, portable instrumentation and oscilloscopes, medical ultrasound beamformers, and industrial non-contact measurement. Industrial-grade temperature range and dual-channel density make it a strong fit when board area and power budget are tightly constrained and two matched channels are needed. When designing with the LTC2141IUP-12, place the part on a continuous ground plane with the exposed pad soldered to multiple thermal vias; this gives the lowest junction-to-ambient thermal resistance. Use short, matched-length differential traces for the analog inputs and keep the analog and digital return currents separated to avoid coupling digital switching noise into the analog front end. Decouple each supply pin with a 0.1uF ceramic capacitor placed as close as possible to the pin, with a bulk 10uF ceramic or tantalum capacitor nearby. This page synthesizes distributor pricing, drop-in package-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFC Hubungi kami
LTC2142IUP-12 - 12-Bit 65Msps Dual ADC | Analog Devices
LTC2142IUP-12

LTC2142IUP-12 - 12-Bit 65Msps Dual ADC | Analog Devices

The Analog Devices LTC2142IUP-12 is a 12-bit, 65 Msps, dual-channel, simultaneous-sampling pipelined analog-to-digital converter (ADC) housed in a 64-pin QFN (9x9 mm, UPF) exposed-pad package. Designed for digitizing high-frequency, wide-dynamic-range signals, the device combines two matched 12-bit ADC cores with on-chip sample-and-hold and a common reference clock to maintain tight inter-channel phase alignment, making it suitable for diversity receivers and I/Q digitizers where channel-to-channel skew would corrupt image rejection. An ADC (analog-to-digital converter) is a semiconductor device that converts continuous-time analog voltages into discrete digital codes at a defined sample rate. High-speed pipelined ADCs use a cascade of low-resolution stages to achieve the best trade-off between speed, resolution, and power; the LTC2142-12 family operates between 25 Msps and 65 Msps to cover a range of communications and instrumentation bandwidths. The LTC2142IUP-12 sits in the hierarchy: pipelined ADC -> ADC -> data converter -> mixed-signal IC -> semiconductor. Key performance specifications include 70.8 dB SNR, 89 dB spurious-free dynamic range (SFDR), ±0.3 LSB INL (typical), ±0.1 LSB DNL (typical), and no missing codes over the industrial temperature range. Transition noise is specified at 0.3 LSB RMS. The output data interface is programmable between full-rate CMOS, double-data-rate CMOS, and double-data-rate LVDS via a parallel or simple SPI-mode serial configuration register. Typical applications include cellular base-station diversity receivers, multi-antenna software-defined radio (SDR) front-ends, medical ultrasound beamformers, and high-speed instrumentation digitizers. The separate output supply (OVDD) lets the CMOS swing range between 1.2 V and 1.8 V, which allows direct connection to low-voltage FPGAs without level shifters. The operating modes of the LTC2142IUP-12 - including output mode, input range, and power-down - are programmed through either a parallel mode-select pin set or the serial interface for finer control. Designers should follow Analog Devices reference layouts for the 9 mm x 9 mm QFN exposed pad to keep the thermal resistance at the published value. When designing with the LTC2142IUP-12, decouple AVDD and OVDD planes separately and route analog inputs as 50 Ω-1 controlled-impedance differential lines terminated at the ADC inputs to preserve the published SNR and SFDR at full input frequency. This page synthesizes distributor pricing across five channels (DigiKey, Mouser, Octopart, Vyrian, and DigChip) together with same-package pin-compatible variants and practical PCB-layout guidance that is not aggregated on any individual distributor listing.

RFC Hubungi kami
LTC2142IUP-14 - 14-Bit 65Msps Low-Power Dual ADC | ADI
LTC2142IUP-14

LTC2142IUP-14 - 14-Bit 65Msps Low-Power Dual ADC | ADI

The Analog Devices LTC2142IUP-14 is a 14-bit, 65 Msps low-power dual-channel simultaneous-sampling pipelined analog-to-digital converter (ADC) housed in a 64-lead 9x9 mm QFN package (UP suffix). The part integrates two matched 14-bit ADC cores that sample on the same clock edge, eliminating inter-channel skew in time-interleaved or I/Q signal chains. What is a dual simultaneous-sampling ADC? A dual ADC is a single integrated circuit containing two matched A/D converter channels that sample their analog inputs at the exact same instant, sharing a common clock. Within the broader signal chain hierarchy, the LTC2142IUP-14 sits inside the data-converter (ADC) class, which is itself a sub-category of data-acquisition ICs, mixed-signal semiconductors, and ultimately integrated circuits. Each converter is preceded by an input track-and-hold and feeds a common reference, allowing direct-IF sampling and quadrature demodulation in communications receivers. Key headline parameters include 14-bit resolution, 65 Msps conversion rate per channel, 73.1 dB SNR, 90 dB SFDR, and a low 100 mW per-channel power dissipation. The device accepts single-ended or differential analog inputs with an input range of 1 Vp-p to 2 Vp-p (set by the MODE pin) and operates from a single 1.8 V analog supply. Digital outputs are LVDS-compatible, easing routing to an FPGA or ASIC across a noisy PCB. A flexible parallel or serial programming interface configures output format, gain, and test patterns. Architecturally, the converter uses a multi-stage pipelined core with proprietary linearization techniques that preserve linearity at high input frequencies, with a typical -3 dB analog input bandwidth of 125 MHz that comfortably exceeds the 65 Msps Nyquist requirement. This makes the part well suited to undersampling intermediate-frequency (IF) signals in wireless infrastructure. Typical applications include 3G/4G cellular base-station receivers, communications imaging, portable instrumentation, ultrasound scanners, and multi-channel data-acquisition cards where channel-to-channel phase coherence is mandatory. Designers frequently pair the LTC2142IUP-14 with low-noise LDOs such as the LT1761 and clock-distribution ICs from the AD951x family. When laying out the PCB, place the analog inputs as close to the ADC pins as possible, use a solid ground plane under the package, and route LVDS outputs with controlled 100 ohm differential impedance. The exposed paddle (EP) must be soldered to a low-impedance ground pad to provide both the electrical ground return and the primary thermal path for the 100 mW internal dissipation. This page synthesizes distributor pricing, package-faithful drop-in alternatives, and applied design notes that go beyond the manufacturer datasheet. It is intended as an engineering-grade reference for BOM managers and hardware designers evaluating the LTC2142IUP-14 for new designs or service replacements.

RFC Hubungi kami
LTC2143CUP-12 - 12-Bit 80Msps Dual ADC | Analog Devices
LTC2143CUP-12

LTC2143CUP-12 - 12-Bit 80Msps Dual ADC | Analog Devices

The Analog Devices LTC2143CUP-12 is a 12-bit, 80 Msps, dual-channel, simultaneous-sampling pipelined analog-to-digital converter (ADC) in a 64-pin QFN (9x9 mm) package. It operates from a single 1.8 V supply and integrates two matched ADC cores, on-chip reference, and configurable CMOS/LVDS output modes for direct connection to FPGAs and DSPs. An ADC (Analog-to-Digital Converter) is a mixed-signal integrated circuit that converts continuous analog waveforms into discrete digital codes for processing by microcontrollers, DSPs, or FPGAs. The pipelined ADC architecture — the hypernym hierarchy of which is: ADC -> data converter -> mixed-signal IC -> semiconductor — is the industry-preferred topology for sample rates from ~10 Msps to >500 Msps because it balances high speed, low power, and small die area. Dual-channel simultaneous-sampling ADCs such as the LTC2143-12 are critical for communications, radar, and I/Q demodulation where two related analog signals must be captured at the exact same instant. Key specifications of the LTC2143CUP-12 include: 12-bit resolution, 80 Msps sample rate, 70.1 dB SNR, 88 dB SFDR, ±0.4 LSB INL (typical), 1.8 V analog/digital supply, and selectable full-scale input range of 1 Vp-p or 2 Vp-p. The serial LVDS output interface (DDR LVDS) supports up to 80 Msps with reduced pin count and excellent common-mode noise rejection. Power consumption is approximately 125 mW per channel at full speed, which is class-leading for the 80 Msps / 12-bit category. Architecturally, the LTC2143-12 uses two interleaved 12-bit pipelined cores with a shared bandgap reference, an on-chip sample-and-hold amplifier, and a digital error-correction block. A self-calibration routine on power-up corrects capacitor mismatch and comparator offset, enabling the 88 dB SFDR performance without external calibration. The inputs are designed for differential drive to maximize even-order harmonic rejection; on-chip common-mode voltage generation simplifies AC-coupling with most modern op-amp drivers. Typical applications for the LTC2143CUP-12 include multi-carrier GSM/EDGE and LTE base-station receivers, diversity radio IF digitization, radar and lidar front-ends, high-speed data acquisition systems, medical imaging (ultrasound beamformers), and communications test equipment. The wide input bandwidth (~750 MHz) also suits the digitizing of IF signals up to ~200 MHz without additional downconversion. When designing with the LTC2143CUP-12, the most important layout consideration is the input network: use a transformer or differential op-amp driver such as the AD8138 with a 25 Ω series resistor at each analog input pin, and place the anti-aliasing RC network as close to the ADC as possible. Decouple the 1.8 V supply with 0.1 µF and 10 µF ceramic capacitors on every supply pin, and keep the LVDS output traces length-matched to within 5 mm to preserve DDR timing margins. This page synthesizes distributor pricing, drop-in same-package alternatives, and design notes that go beyond the manufacturer datasheet — including a parameter-by-parameter comparison table and an explicit selection guide for choosing the LTC2143CUP-12 versus faster or higher-resolution members of the LTC2145-12 / LTC2144-12 / LTC2143-12 family.

RFC Hubungi kami
LTC2143CUP-14 - 14-Bit 80Msps Dual ADC | Analog Devices
LTC2143CUP-14

LTC2143CUP-14 - 14-Bit 80Msps Dual ADC | Analog Devices

The Analog Devices LTC2143CUP-14 is a 14-bit, 80 Msps, low-power dual pipelined analog-to-digital converter (ADC) housed in a 64-lead QFN (9x9) exposed-pad package. The two simultaneously-sampling differential input channels make it well suited for digitizing I/Q baseband, communications IF strips, and multi-channel instrumentation front ends where channel-to-channel phase coherence matters. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that samples a continuous-time analog voltage and produces a discrete digital code representing its amplitude. Pipelined ADCs achieve a favorable trade-off between sample rate (tens to hundreds of MSPS) and resolution (10-16 bits) by cascading multiple low-resolution stages with inter-stage residue amplification; they are the dominant architecture in communications, imaging, and test-and-measurement front ends. Dual-channel pipelined ADCs such as the LTC2143CUP-14 simultaneously quantize two analog inputs so downstream DSP can recover quadrature relationships, multi-antenna phase, or multi-sensor time correlation. Key specifications include ±1 LSB typical INL, ±0.3 LSB typical DNL with no missing codes over the full temperature range, 1.2 LSB RMS transition noise, and flexible digital outputs supporting full-rate CMOS, double-data-rate CMOS, or double-data-rate LVDS. A separate output supply pin lets the CMOS swing range from 1.8 V to 3.3 V independent of the analog 1.8 V core rail, simplifying interface to FPGAs and ASICs on different I/O voltage domains. Typical applications include cellular base-station receivers, software-defined radio (SDR) front ends, multi-channel data acquisition cards, medical ultrasound beamformers, and portable battery-powered instrumentation. The 64-QFN (9x9) exposed pad keeps the package compact while providing a low thermal-resistance path that is essential for the multilayer board ground-plane layout recommended by the manufacturer datasheet. A clean unbroken ground plane in the layer immediately beneath the ADC is required to achieve the published SNR/SFDR performance. A primary design consideration is bypassing the analog and digital rails with low-ESR ceramic capacitors placed within 2 mm of each supply pin and tying the exposed pad to a solid ground pour with at least 16 thermal vias. The internal reference can be disabled in favor of an external reference when tighter gain error or channel matching is required across multiple ADCs.

RFC Hubungi kami
LTC2143IUP-12 - 12-Bit 80Msps Dual ADC, 64-QFN | Analog Devices
LTC2143IUP-12

LTC2143IUP-12 - 12-Bit 80Msps Dual ADC, 64-QFN | Analog Devices

The Analog Devices LTC2143IUP-12 is a 12-bit, 80 Msps, dual-channel, low-power pipelined analog-to-digital converter (ADC) housed in a 64-pin QFN (UP, 9x9 mm) package with exposed pad. The part is specified for the industrial temperature range (-40C to +85C) and operates from a single 1.8 V supply, drawing approximately 100 mW per channel at full sample rate. Per the LTC2145-12/LTC2144-12/LTC2143-12 family datasheet, the device features 70.6 dB SNR and 89 dB spurious-free dynamic range, with simultaneous sampling of two differential analog input channels. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that converts real-world analog waveforms into discrete digital codes for processing, storage, or transmission. The pipelined ADC architecture — of which the LTC2143IUP-12 is an instance — uses multiple low-resolution stages (typically 1.5 bits/stage) with inter-stage residue amplifiers to achieve high sampling rates at moderate resolution. Pipelined ADCs sit within the broader hierarchy: ADC → data converter → mixed-signal IC → semiconductor. They are the workhorse choice for communications, imaging, and test-and-measurement systems that require multi-MHz input bandwidth and 10-14 bits of resolution. The LTC2143IUP-12 supports input bandwidths up to approximately 750 MHz, allowing it to under-sample IF signals in communications receivers. Internal voltage reference, programmable digital output timing, and flexible LVDS/CMOS output modes simplify board-level integration. The dual, matched channels eliminate skew between ADC paths in MIMO or diversity receivers, while per-channel gain and offset adjustment registers help correct channel-to-channel mismatches at the system level. The 1.8 V single-supply architecture plus low power (about 100 mW per channel at 80 Msps) makes the LTC2143IUP-12 well suited for portable and thermally-constrained instrumentation. Optional LVDS outputs minimize digital switching noise on the board, which is critical when the analog inputs are at the millivolt level. Programmable full-scale input range (1 Vpp or 2 Vpp differential) gives designers headroom when interfacing with a variety of front-end amplifiers and anti-alias filters. Typical applications include cellular base-station receivers, software-defined radio (SDR) platforms, medical imaging front ends, portable test and measurement equipment, and multi-channel data acquisition systems. The wide input bandwidth also suits digital oscilloscopes and spectrum analyzer front ends. When designing with the LTC2143IUP-12, place the analog input traces as 100-ohm differential pairs with a grounded coplanar-waveguide structure, and keep the exposed pad soldered to a continuous ground plane for thermal dissipation and low-impedance return. Use the internal reference by default and decouple AVDD/DVDD/OVRDV with 0.1 uF and 10 uF ceramic capacitors as close to the pins as possible. This page synthesizes DigiKey and Mouser stock/pricing, drop-in pin-compatible alternatives in the same 64-QFN footprint, and practical design notes drawn from the Analog Devices datasheet — information that you will not find on any single distributor page.

RFC Hubungi kami
LTC2144CUP-14 - 14-Bit 105Msps Dual ADC | Analog Devices
LTC2144CUP-14

LTC2144CUP-14 - 14-Bit 105Msps Dual ADC | Analog Devices

The Analog Devices LTC2144CUP-14 is a 14-bit, 105 Msps dual-channel simultaneous-sampling pipelined analog-to-digital converter (ADC) housed in a 64-lead QFN (9x9 mm) package with exposed pad, designed for digitizing high-frequency, wide-dynamic-range signals in communications and imaging systems. Key specifications per the Analog Devices datasheet include a 14-bit resolution, 105 Msps sample rate per channel, two synchronized sample-and-hold inputs for simultaneous acquisition, and a low-power CMOS architecture intended for portable and high-density multi-channel designs. What is a simultaneous-sampling ADC? A simultaneous-sampling ADC is a converter with two or more sample-and-hold front-ends and typically one or more internal conversion cores that capture multiple analog channels at the exact same instant. Compared with multiplexed ADCs that interleave channels in time, simultaneous sampling preserves inter-channel phase relationships, which is critical in MIMO radar, beamforming, I/Q demodulation, and multi-axis vibration analysis. The LTC2144CUP-14 features a pipelined conversion architecture, a differential or single-ended analog input front-end per channel, an internal voltage reference, and an LVDS/CMOS-compatible digital output interface (selectable by part variant within the LTC2143-14/LTC2144-14/LTC2145-14 family). The 64-lead QFN-EP package exposes a thermal pad that drops the junction-to-ambient thermal resistance far below a non-EP equivalent, enabling reliable operation at full 105 Msps in space-constrained layouts. Typical applications include digital oscilloscopes, communications test equipment, MIMO and phased-array radar front-ends, medical imaging (ultrasound beamformers), and high-speed data acquisition cards for industrial and defense systems. When designing with this part, allocate a solid ground plane under the exposed pad and decouple each analog supply pin with a 0.1 uF plus 10 uF capacitor pair placed within 5 mm of the pin to preserve SFDR and SNR. This page synthesizes distributor pricing, drop-in alternatives from the LTC2143/LTC2144/LTC2145 family, and practical design notes not found in the manufacturer datasheet alone.

RFC Hubungi kami
LTC2144IUP-12 - 12-Bit 105Msps Dual ADC | Analog Devices
LTC2144IUP-12

LTC2144IUP-12 - 12-Bit 105Msps Dual ADC | Analog Devices

The Analog Devices LTC2144IUP-12 is a 12-bit, 105 Msps, dual-channel simultaneous-sampling pipelined analog-to-digital converter (ADC) housed in a 64-lead QFN (9x9 mm) package with an exposed pad. It is part of the LTC2145-12/LTC2144-12/LTC2143-12 family that delivers 70.6 dB SNR and 89 dB spurious-free dynamic range (SFDR) for digitizing high-frequency, wide dynamic range signals. Ultralow 0.08 ps RMS jitter allows IF undersampling with excellent noise performance. An ADC (Analog-to-Digital Converter) is a mixed-signal integrated circuit that converts continuous-time analog voltages into discrete digital codes. Pipelined ADCs use a multi-stage architecture to achieve high sample rates (tens to hundreds of Msps) while keeping per-stage hardware compact; dual simultaneous-sampling ADCs capture two channels at exactly the same instant, eliminating channel-to-channel skew in I/Q or diversity receivers. Within the power management and data-converter taxonomy, the LTC2144IUP-12 belongs to high-speed pipelined ADCs -> data converters -> mixed-signal ICs -> integrated circuits. Key features of this part include 105 Msps per channel sample rate, 12-bit resolution, 70.6 dB SNR, 89 dB SFDR, 0.08 ps RMS aperture jitter, and a parallel CMOS/LVDS output interface selectable per channel. The 64-QFN (UP) exposed-pad package provides low thermal resistance (~28 C/W theta_JC via the pad), enabling operation across the industrial -40C to +85C temperature range. The pipelined architecture uses 12 internal stages with per-stage flash sub-ADC and MDAC residue amplification; sample-and-hold is on-chip and front-end differential, supporting 1 Vp-p to 2 Vp-p full-scale inputs. A separate output supply (OVDD) lets the digital outputs drive 1.8V to 3.3V logic while the analog core runs from 1.8V. Typical applications include communications receivers, cellular base-station digitizers, radar/sonar signal chains, medical imaging front-ends, and portable test instrumentation. Designers commonly pair it with the AD8138 differential driver at the input and an FPGA for the parallel data capture. Design trade-off: at 105 Msps with 1.8V analog supply, expect roughly 100 mW per channel dissipation. Use the exposed pad with a continuous ground plane and bypass AVDD with 10 uF + 0.1 uF ceramic as close as possible to each pin pair. This page synthesizes distributor pricing, drop-in same-package alternatives, and application-specific design notes not found in the manufacturer datasheet alone.

RFC Hubungi kami
LTC2144IUP-14 - 14-Bit, 105Msps Dual ADC | Analog Devices
LTC2144IUP-14

LTC2144IUP-14 - 14-Bit, 105Msps Dual ADC | Analog Devices

The Analog Devices LTC2144IUP-14 is a 14-bit, 105 Msps low-power dual simultaneous-sampling analog-to-digital converter (ADC) housed in a 64-pin QFN (9x9 mm) exposed-pad package. Each of the two integrated channels samples at up to 105 MSPS with pipelined architecture, and the device draws only 312 mW total (approximately 156 mW per channel) from a single 1.8 V supply, with an optional 2.5 V drive for the LVDS/CMOS outputs. What is a dual pipelined ADC? A dual pipelined ADC is an analog-to-digital converter that integrates two independent sample-and-hold front-ends followed by multi-stage switched-capacitor pipeline stages. The architecture enables two channels to be digitized simultaneously, which is critical for applications such as MIMO wireless transceivers, diversity radar, and quadrature (I/Q) signal processing where phase coherence between channels determines system performance. Key features include 73.4 dB SNR and 90 dB SFDR at 70 MHz input, an internal transparent dither circuit that improves SFDR at low input frequencies, and a serial SPI port for mode configuration. The LTC2144-14 family supports CMOS, DDR CMOS, or DDR LVDS output modes, allowing flexible interface to FPGAs and ASICs. A built-in clock duty-cycle stabilizer relaxes PCB clock-routing constraints. The LTC2144IUP-14 is engineered for high-channel-count multi-board systems: a multi-lane serial output mode produces a single-lane serial data stream per channel, reducing FPGA pin count. Internal bandgap reference and proprietary pipeline design eliminate the need for external reference decoupling in most applications, reducing BOM cost. Pin compatibility with the 12-bit LTC2144-12 and 14-bit LTC2143-14 (80 MSPS) variants provides an easy resolution/sample-rate upgrade path within the same QFN-64 footprint. Typical applications include communications basestations (MIMO LTE/WCDMA diversity receivers), handheld portable instrumentation, medical imaging (ultrasound beamforming front-ends), and defense electronics such as phased-array radar digitizers. The industrial temperature range (-40C to +85C) supports outdoor and uncontrolled-environment deployments. When designing with this device, provide a clean low-noise ground plane directly under the exposed pad, route the 105 MHz encode clock as a 50 ohm controlled-impedance trace, and bypass each analog supply pin with a 0.1 uF X7R ceramic capacitor within 3 mm of the pin. The IUP suffix denotes the industrial-grade (-40C to +85C) package. This page synthesizes distributor pricing, drop-in alternatives, and practical layout guidance not found in the bare datasheet, with cross-references to companion Linear Technology ADC families.

RFC Hubungi kami
LTC2145CUP-12 - 12-Bit 125Msps Dual ADC, 1.8V, 64-QFN | Analog Devices
LTC2145CUP-12

LTC2145CUP-12 - 12-Bit 125Msps Dual ADC, 1.8V, 64-QFN | Analog Devices

The Analog Devices LTC2145CUP-12 is a 12-bit, 125 Msps, dual-channel, low-power analog-to-digital converter housed in a 64-lead (9 mm x 9 mm) QFN-EP package with exposed thermal pad. The device operates from a single 1.8 V analog supply, integrates two simultaneous-sampling pipelined ADC channels, and supports a separate digital I/O supply that can range from 1.2 V to 1.8 V for flexible logic interfacing. The C-grade commercial temperature range spans 0 °C to +70 °C. A pipelined ADC is a high-speed analog-to-digital converter architecture that uses multiple cascaded low-resolution stages, each producing a partial conversion with its own sample-and-hold, sub-ADC, and DAC. The pipeline architecture enables high conversion rates (tens to hundreds of Msps) at moderate power dissipation, making pipelined ADCs the workhorse of communications, radar, instrumentation, and imaging front-ends. The LTC2145CUP-12 belongs to the converter -> ADC -> high-speed ADC -> pipelined ADC hierarchy within Analog Devices' data-converter portfolio. Key specifications include ±0.3 LSB typical INL, ±0.1 LSB typical DNL with no missing codes over temperature, 0.3 LSB RMS transition noise, 70.6 dB SNR, 89 dB spurious-free dynamic range (SFDR), and 0.08 ps RMS ultra-low aperture jitter. Differential analog inputs are required to achieve the rated AC performance. The outputs are software-configurable as full-rate CMOS, double-data-rate (DDR) CMOS, or DDR LVDS. The pipelined core delivers two simultaneous conversions per sample clock with on-chip track-and-hold. The 0.08 ps RMS jitter specification is what enables undersampling of IF frequencies in communications receivers without SNR penalty - the part can capture narrowband IF signals well above Nyquist while preserving the analog input's dynamic range. The flexible output modes (CMOS / DDR CMOS / DDR LVDS) let designers trade off pin count, board complexity, and EMI against the lowest possible latency. Typical applications include cellular base-station receivers and digital predistortion feedback paths, multi-carrier software-defined-radio (SDR) platforms, medical ultrasound beamformers, and portable or battery-powered test and measurement instruments. The wide input bandwidth and low jitter allow direct IF sampling, eliminating a down-conversion stage in many radio architectures. When designing with this part, pay close attention to the analog input network: a differential transformer or fully differential driver (such as the AD8138 or ADA4927) must precede the ADC inputs, and the analog and digital grounds must be carefully partitioned on the PCB. Output mode selection is made via the MODE pin and is latched on reset; verify the mode configuration against your FPGA or ASIC capture logic before layout. This page synthesizes distributor pricing, drop-in-compatible variants, and practical layout notes drawn from Analog Devices application notes and reference designs - context not collected on a single distributor listing.

RFC Hubungi kami
LTC2150CUJ-12 - 12-Bit 170Msps Single-Channel ADC | Analog Devices
LTC2150CUJ-12

LTC2150CUJ-12 - 12-Bit 170Msps Single-Channel ADC | Analog Devices

The Analog Devices LTC2150CUJ-12 is a 12-bit, 170 Msps single-channel pipelined analog-to-digital converter (ADC) housed in a 40-lead 6 mm × 6 mm QFN package (UJ suffix, CUJ ordering code). The converter operates from a single 1.8 V analog supply and a separate 1.8 V to 3.3 V digital I/O supply, making it well suited to low-power, high-density digital systems that already have an LVDS or CMOS interface rail nearby. An ADC is a mixed-signal integrated circuit that converts continuous-time analog voltages into discrete digital codes at a sampling rate set by an external clock. Pipelined ADCs such as the LTC2150CUJ-12 use multi-stage conversion to achieve high sampling rates at low power; the LTC2150-12 family sits inside the broader product hierarchy of ADC -> data converter -> mixed-signal IC -> semiconductor, and is offered in 12-bit and 14-bit pin-compatible versions to simplify migration between resolutions. Key features include a 1.25 GHz full-power analog input bandwidth, an optional integrated sample-and-hold front end, clock duty-cycle stabilization for clean Nyquist operation, low-power Sleep and Nap modes, and a serial SPI port for register configuration. The device offers pin-compatibility with 14-bit versions of the same family, allowing PCB reuse between 12-bit and 14-bit designs without layout changes. Differential analog input drive is required to realize the full AC linearity. Typical applications include broadband communications, digital predistortion feedback loops in wireless base stations, cable-modem downstream receive paths, and high-speed test instrumentation. Designers value the LTC2150CUJ-12 for low noise, low latency, and the ability to interface to FPGAs and ASICs over LVDS or CMOS at system sample rates up to 170 Msps.

RFC Hubungi kami
LTC2150CUJ-14 - 14-Bit 170Msps 1.8V ADC DDR LVDS | Analog Devices
LTC2150CUJ-14

LTC2150CUJ-14 - 14-Bit 170Msps 1.8V ADC DDR LVDS | Analog Devices

The Analog Devices LTC2150CUJ-14 is a single-channel, 14-bit, 170 Msps pipelined analog-to-digital converter (ADC) housed in a 40-lead QFN (6 mm × 6 mm) package with an exposed pad. It operates from a single 1.8 V analog and digital supply and produces double-data-rate (DDR) LVDS digital outputs, making it well suited for direct connection to FPGA and ASIC capture buffers. A pipelined ADC is a successive-stage converter that resolves the input sample through a cascade of low-resolution flash stages interleaved with sample-and-hold amplifiers; this architecture delivers high sample rates (hundreds of Msps) with low latency (five clock cycles here) and excellent dynamic linearity. Within the broader signal-chain taxonomy, the LTC2150CUJ-14 sits as ADC -> data converter -> signal-chain IC -> semiconductor, occupying the digitisation stage between an analog front end (AFE, amplifier or downconverter) and a digital processor (FPGA/DSP/ASIC). Key headline parameters per the manufacturer datasheet 21521014fa: ±0.85 LSB typical INL, ±0.25 LSB typical DFL, no missing codes over temperature, 1.82 LSBRMS transition noise, 1.25 GHz full-power sample-and-hold bandwidth, and optional clock duty-cycle stabilizer for high performance across non-50% clock duty cycles. The differential ENC+/ENC- encode clock accepts sine, PECL, LVDS, TTL, or CMOS drivers, simplifying clocking from FPGA PLLs or crystal oscillators. The part integrates a serial SPI port for per-channel configuration (output mode, test patterns, power modes), low-power Sleep and Nap modes for power-managed applications, and a pin-compatible 12-bit upgrade path (LTC2150-12 / LTC2151-14 / LTC2152-14 family) for code re-use across 12/14-bit and 170/210/250 Msps variants. Differential analog and clock inputs maximise second-order linearity and common-mode rejection. Typical applications include cellular basestation receiver IF digitisation, medical imaging front ends (ultrasound beamformers, MRI receivers), radar and electronic-warfare IF sampling, cable-modem head-end CMTS downstream capture, broadband communications test equipment, and high-speed oscilloscope/data-acquisition front ends. Designers typically pair it with an AD8138 differential driver on the analog input, an AD9520 clock generator for ENC+, and an FPGA (e.g. Xilinx Kintex, Intel Cyclone) for LVDS capture. When designing with the LTC2150CUJ-14, follow the layout guidelines in the evaluation board DC1565A-C: solid ground planes under the exposed pad, length-matched 50 Ω LVDS output traces, and 0.1 µF + 10 µF decoupling close to each supply pin. Power dissipation is roughly proportional to sample rate and output mode, so enable Nap or Sleep mode when the converter is idle to meet system power budgets. This page synthesises distributor pricing, drop-in same-family alternatives, and practical design guidance that is not consolidated in the manufacturer datasheet.

RFC Hubungi kami
LTC2151CUJ-14 - 14-Bit 210Msps ADC, DDR LVDS, 40-QFN | ADI
LTC2151CUJ-14

LTC2151CUJ-14 - 14-Bit 210Msps ADC, DDR LVDS, 40-QFN | ADI

The Analog Devices LTC2151CUJ-14 is a 14-bit, 210 Msps pipelined analog-to-digital converter (ADC) housed in a 40-lead QFN (6x6 mm) package. The -14 speed grade operates at 210 Msps, while the family also includes the LTC2152-14 at 250 Msps and LTC2150-14 at 170 Msps, sharing the same pinout. The device targets demanding communications applications with AC performance that includes 70 dB SNR and 90 dB spurious-free dynamic range (SFDR), plus a 1.25 GHz input bandwidth enabling accurate undersampling of high-IF signals. An ADC (analog-to-digital converter) is a semiconductor that samples continuous analog voltages and converts them into discrete digital codes for downstream DSP, FPGA, or processor-based signal chains. Pipeline ADCs like the LTC2151-14 achieve a balance between high sampling rate, moderate resolution, and low latency - here, only five clock cycles - making them ideal for multi-carrier base stations, broadband digital pre-distortion, and software-defined radio. Within the broader taxonomy, this part is a high-speed ADC -> data converter -> signal chain IC -> mixed-signal semiconductor. Key specifications include +/-0.85 LSB INL (typical), +/-0.25 LSB DNL (typical), no missing codes over temperature, and 1.82 LSB RMS transition noise. The digital outputs are double-data-rate (DDR) LVDS, simplifying FPGA capture at full speed. The ENC+ and ENC- encode inputs accept differential sine wave, PECL, LVDS, TTL, or CMOS drive, and an optional clock duty-cycle stabilizer (DCS) maintains SNR across non-50% duty-cycle clock sources. Architecturally, the LTC2151-14 uses a multi-stage pipelined switched-capacitor core stabilized by an internal bandgap reference. The differential analog input pair is designed to be driven through a transformer or differential amplifier for best second-order distortion performance; a 1.25 GHz analog front-end allows IF sampling well above Nyquist. The DDR LVDS interface reduces the output pin count and eases FPGA I/O timing closure at hundreds of MHz. Typical applications include cellular base-station receivers, cable and broadband digital pre-distortion (DPD) feedback paths, test and measurement instrumentation, radar and LIDAR signal acquisition, and software-defined radios. The combination of wide input bandwidth and high SFDR suits multi-carrier GSM/WCDMA/LTE systems where adjacent carriers must remain distinguishable. Designers should pay particular attention to analog input network design - a 1:1 transformer or differential driver is recommended to realize the full 90 dB SFDR - and to FPGA LVDS capture timing because DDR mode halves the available timing budget. Place the part on a low-noise analog supply layer with decoupling close to each supply pin. This page synthesizes distributor stock, pricing, and pin-compatible drop-in alternatives (LTC2150CUJ-14 in the same family, plus competitor equivalents) alongside practical design considerations not duplicated in the manufacturer datasheet.

RFC Hubungi kami
LTC2151IUJ-12 - 12-Bit 210Msps ADC, 40-QFN | Analog Devices
LTC2151IUJ-12

LTC2151IUJ-12 - 12-Bit 210Msps ADC, 40-QFN | Analog Devices

The Analog Devices LTC2151IUJ-12 is a single-channel 12-bit pipelined analog-to-digital converter (ADC) sampling at 210 Msps, packaged in a 40-lead 6mm x 6mm QFN (UJ suffix) with an exposed thermal pad. It is part of the LTC2152-12/LTC2151-12/LTC2150-12 pin-compatible ADC family, designed for digitizing high-frequency, wide-dynamic-range signals in communications, instrumentation, and defense imaging systems. A pipelined ADC is a high-speed converter architecture that processes the analog input through multiple low-resolution stages in parallel, each stage producing a sub-ADC residue that is digitized by the next stage. This approach enables sample rates well above what successive-approximation architectures can achieve, while maintaining low latency and good spurious-free dynamic range (SFDR). The LTC2151-12 sits at the top of the signal-chain hierarchy: analog sensor -> anti-alias filter -> pipelined ADC -> FPGA/ASIC digital processing. Key features include 1.25 GHz full-power bandwidth sample-and-hold, an optional clock duty-cycle stabilizer for jitter-insensitive operation, and low-power Sleep and Nap modes that reduce dissipation when the converter is idle. The serial SPI port allows in-system configuration of output format, gain, offset, and channel modes. Pin-compatible 14-bit versions (LTC2251-14 family) allow system scalability by swapping the ADC without PCB rework. The device accepts differential or single-ended analog inputs and produces LVDS, parallel CMOS, or serialized LVDS outputs selectable via SPI, simplifying interface to FPGAs. Excellent AC performance with high SFDR makes the LTC2151-12 suitable for directly digitizing IF signals in software-defined radio and radar receivers where spurious content can mask weak targets. Typical applications include cellular base-station receivers, radar and electronic-warfare signal processing, medical imaging front-ends, and high-speed data acquisition cards. The wide input bandwidth permits undersampling of IF carriers, reducing system cost by eliminating a downconversion stage. When designing with this ADC, ensure the analog input network presents 50 ohm (or 200 ohm differential) termination and that the encode clock source has low jitter (<200 fs RMS) to preserve SNR at high input frequencies. The exposed pad must be soldered to a continuous ground plane for thermal and electrical performance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including parametric cross-reference guidance for engineers migrating between the 12-bit and 14-bit LTC215x family members.

RFC Hubungi kami
LTC2152IUJ-12 - 12-Bit 250Msps ADC, Single 1.8V Supply, 40-QFN | Analog Devices
LTC2152IUJ-12

LTC2152IUJ-12 - 12-Bit 250Msps ADC, Single 1.8V Supply, 40-QFN | Analog Devices

The Analog Devices LTC2152IUJ-12 is a single-channel 12-bit analog-to-digital converter (ADC) sampling at up to 250 Msps, housed in a 40-lead 6x6 mm QFN package (UJ suffix). It is one of three speed grades in the LTC215x-12 family, alongside the 210 Msps LTC2151-12 and the 170 Msps LTC2150-12, and operates from a single 1.8 V analog supply with a separate 1.8 V digital supply for low-noise mixed-signal integration. An ADC (analog-to-digital converter) is a mixed-signal integrated circuit that samples continuous-time analog voltages at discrete instants and quantises them into binary codes; pipeline ADCs such as the LTC2152-12 use a multi-stage switched-capacitor architecture that delivers high sample rates while preserving resolution. The LTC2152-12 belongs to the category hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor, serving communications, instrumentation, and defence systems that demand wide-bandwidth, high-dynamic-range signal acquisition. Key differentiating specifications include 12-bit resolution at 250 Msps real sampling rate, 1.8 V single supply operation, an internal high-bandwidth track-and-hold, differential analog inputs (per datasheet, the inputs must be driven differentially for specified performance), CMOS or DDR LVDS digital-output modes selectable per application, and a low-jitter clock PLL that relaxes the front-end analog filter requirements. The 40-QFN (6x6) package integrates an exposed pad that anchors the thermal and grounding strategy. Architecture-wise, the converter uses a pipelined core with digital error correction across multiple 1.5-bit-per-stage sub-ADCs, weighted against a precision reference and reconstructed by a latency-corrected output stage; this approach delivers spurious-free dynamic range (SFDR) suitable for multi-carrier wireless basestations and pulsed radar receivers where spurious content must remain well below the wanted signal. Typical applications include wideband digitisation of IF/RF signals in wireless infrastructure, digital oscilloscopes and spectrum analysers, radar and electronic-warfare receivers, cable-headend DOCSIS upstream capture, and medical ultrasound beamforming front-ends. The -IUJ suffix indicates the industrial temperature range (-40C to +85C) per ADI's part-numbering convention. When designing with this part, follow ADI's recommended differential input drive network (balun or transformer-coupled op-amp), place the analog and digital 1.8 V rails on separate PCB planes with a ferrite bead between them, and expose the bottom-side thermal pad with adequate vias to a ground pour - the package lead frame cannot dissipate the converter's full-load power without this copper area. This page synthesises ADI datasheet extracts, distributor pricing as of 2026-10-13, and a drop-in alternatives list not found on a single distributor page, giving engineers a faster cross-package/parametric path than re-querying DigiKey or Mouser manually.

RFC Hubungi kami
LTC2152IUJ-14 - 14-Bit 250Msps ADC, 40-QFN | Analog Devices
LTC2152IUJ-14

LTC2152IUJ-14 - 14-Bit 250Msps ADC, 40-QFN | Analog Devices

The Analog Devices LTC2152IUJ-14 is a 14-bit, 250 Msps single-channel pipelined analog-to-digital converter (ADC) housed in a 40-lead QFN (6 mm x 6 mm) package with an exposed pad for thermal dissipation. Per the LTC2152-14 family datasheet (21521014fa), it features ±0.85 LSB INL (typical), ±0.25 LSB DNL (typical), no missing codes over temperature, and 1.82 LSBRMS transition noise, providing accurate conversion for high-speed signal acquisition. The wideband input supports a 1.4 GHz analog front-end, enabling excellent spurious-free dynamic range at high intermediate frequencies for communications and instrumentation front ends. DDR LVDS digital outputs simplify FPGA/ASIC interface alignment, while the differential ENC+/ENC- sample clock accepts sine, PECL, LVDS, TTL, or CMOS drive levels and an optional clock duty-cycle stabilizer preserves SNR across non-50% duty clocks. Industrial temperature grade (-40°C to +85°C) and a precision internal reference make the LTC2152IUJ-14 well-suited to demanding IF sampling, LTE/WiMAX base stations, and multi-carrier software-defined radio platforms. Common applications also include medical imaging, radar/LIDAR digitizers, and high-end test/measurement digitizer boards where the wide input bandwidth and low latency (six clock cycles) maximize usable signal headroom. At 250 Msps, typical power consumption allows fanless operation with adequate PCB copper on the exposed pad. According to the manufacturer datasheet, the LTC2152IUJ-14 is pin-compatible with the LTC2150-14 (170 Msps) and LTC2151-14 (210 Msps) in the same 40-QFN, giving designers a clear migration path when system sample-rate requirements change late in development. The industrial temperature grade ("I" suffix) and lead-free ("PBF") designation also qualify the part for harsh-environment embedded and ruggedized platforms. This page synthesizes distributor pricing, drop-in same-package alternatives (LTC2150/LTC2151 family), and practical PCB/layout guidance not found in the manufacturer datasheet alone.

RFC Hubungi kami
LTC2155CUP-12 - Dual 12-Bit 170Msps ADC | Analog Devices
LTC2155CUP-12

LTC2155CUP-12 - Dual 12-Bit 170Msps ADC | Analog Devices

The Analog Devices LTC2155CUP-12 is a dual 12-bit 170 Msps analog-to-digital converter (ADC) designed for digitizing high-frequency, wide dynamic range signals. Housed in a 64-lead QFN (9 mm × 9 mm) package, the LTC2155CUP-12 delivers 68.5 dB SNR and 90 dB SFDR, while consuming only 545 mW total from a single 1.8 V supply. The device supports a single 1.8 V supply with DDR LVDS outputs and an easy-to-drive 1.5 V peak-to-peak input range. What is a pipelined ADC? A pipelined analog-to-digital converter is a high-speed ADC architecture that breaks the conversion into multiple low-resolution stages, each handling one sample per clock cycle. This pipeline approach enables high sampling rates (hundreds of Msps) while maintaining moderate resolution (10-16 bits), making pipelined ADCs the standard for communications, radar, and instrumentation applications. The LTC2155 belongs to the dual-pipelined ADC category, integrating two matched ADC channels on a single die for I/Q baseband or diversity reception. Key features of the LTC2155CUP-12 include a 1.25 GHz full-power bandwidth sample-and-hold, an optional clock duty cycle stabilizer, low-power sleep and nap modes, and a serial SPI port for configuration. The pin-compatible 14-bit versions (LTC2157-14/LTC2156-14/LTC2155-14) allow easy migration when higher dynamic range is needed. The differential inputs are easy to drive, simplifying front-end design for direct-IF sampling receivers. The architecture uses a high-speed pipelined core with on-chip reference and sample-and-hold, achieving excellent linearity and low jitter. DDR LVDS outputs simplify data capture by providing one data pair per channel per clock edge, reducing the number of data lines routed on the PCB. The internal duty cycle stabilizer compensates for clock source imperfections, preserving SNR at high input frequencies. Typical applications include communications receivers, cellular base stations, radar and LiDAR signal chains, portable instrumentation, medical imaging front-ends, and software-defined radio (SDR) platforms. The combination of dual channels, low power, and small QFN-64 footprint makes the LTC2155CUP-12 particularly suited to multi-channel compact systems. When designing with this ADC, pay close attention to the analog input network: a differential transformer or driver amplifier must present 1.5 V peak-to-peak to maximize SNR. Use low-jitter clock sources and matched-length differential output pairs to preserve LVDS timing margins at 170 Msps. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFC Hubungi kami
LTC2155CUP-14 - Dual 14-Bit 170Msps ADC | Analog Devices
LTC2155CUP-14

LTC2155CUP-14 - Dual 14-Bit 170Msps ADC | Analog Devices

The Analog Devices LTC2155CUP-14 is a dual-channel, 14-bit, 170 Msps pipelined analog-to-digital converter housed in a 64-pin QFN (9x9 mm) package. It integrates two simultaneously-sampling ADC channels with parallel CMOS outputs, supports differential inputs, and operates from a 1.7 V to 1.9 V analog supply, drawing approximately 1.0 W per pair of channels at full sample rate. An ADC (Analog-to-Digital Converter) is a data converter IC that transforms continuous analog signals into discrete digital codes for processing by FPGAs, ASICs, DSPs or microcontrollers. Within the converter hierarchy, the LTC2155CUP-14 sits in the high-speed pipelined sub-family, which is the architecture of choice for communications, radar, instrumentation, and defense applications where tens-to-hundreds of Msps are required with 12-16 bit resolution. Pipelined ADCs use a multi-stage switched-capacitor architecture with per-stage residue amplifiers and digital error correction, achieving high sample rates at moderate power while maintaining low latency suitable for many baseband and IF signal chains. Key specifications include 14-bit resolution, 170 Msps sampling rate per channel, 70.1 dB SNR (with 100 MHz input) and 88 dB SFDR, plus a 1.4 GHz analog input bandwidth. The part supports both DDR (Double Data Rate) CMOS and DDR LVDS output modes, and accepts differential analog inputs, enabling direct interface to differential IF chains without external gain blocks. Internal PLL/VCO and clock duty-cycle stabilizer simplify board-level clocking, and per-channel gain/offset adjustment is supported via SPI. Typical applications include broadband communications receivers, LTE/4G base-station digitizers, software-defined radio (SDR), radar and electronic-warfare IF sampling, medical imaging front-ends, and high-speed data acquisition cards for test and measurement. Differential input topology and selectable output modes also simplify interface to Altera/Xilinx FPGAs and high-speed ASICs. When designing with the LTC2155CUP-14, observe proper analog/digital ground partitioning, place bypass capacitors as close as possible to AVDD/DVDD pins, and follow Analog Devices' differential input-balun network recommendations to realize the listed SNR/SFDR performance. Output data format and timing must match the chosen FPGA capture IP. This page synthesizes distributor pricing, drop-in alternatives drawn from the LTC2155 and pin-compatible Linear Technology/Analog Devices families, and practical design notes not consolidated in the manufacturer datasheet.

RFC Hubungi kami