Produk (44,000+)

MC1458PS - Dual 30V 1MHz Op Amp | Texas Instruments
MC1458PS

MC1458PS - Dual 30V 1MHz Op Amp | Texas Instruments

The Texas Instruments MC1458PS is a dual general-purpose operational amplifier with two internally compensated amplifier channels, a 30 V rating, and a 1 MHz gain-bandwidth product in an 8-pin SOIC package. The MC1458 family combines short-circuit protection, wide common-mode and differential input-voltage ranges, low power consumption, and latch-up-free operation. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to compare and amplify small voltage differences. The MC1458 belongs to the general-purpose operational-amplifier family within the broader analog IC and semiconductor hierarchy. Its two channels can operate independently for signal conditioning, voltage following, summing, integration, or other feedback-based amplifier configurations. Each MC1458 channel offers a 1 MHz gain-bandwidth product, 500 V/ms slew rate, and 90 dB common-mode rejection in the supplied product data. The reported input bias current is 1.5 µA, input offset current is 200 nA, and typical input offset voltage is 6 mV. Internal frequency compensation eliminates the need for external compensation components in the manufacturer's standard voltage-follower application. The MC1458 architecture is intended for general-purpose precision amplification rather than high-speed or rail-to-rail operation. Its wide common-mode input range makes it suitable for conventional bipolar-supply circuits, while the absence of latch-up improves robustness during power sequencing and input-overvoltage events. Short-circuit protection helps limit output current when an output is overloaded, although sustained short-circuit duration and internal current limits should be confirmed in the manufacturer datasheet. Typical uses include audio preamplification, summing amplifiers, active filters, sensor-signal conditioning, industrial control blocks, and general voltage-following circuits. Two amplifiers in one package can reduce component count and simplify dual-channel or differential signal-path layouts. The commercial MC1458PS temperature grade is 0 °C to +70 °C, making it appropriate for room-temperature industrial and consumer equipment rather than exposed automotive or extreme-temperature installations. PCB design should reserve adequate copper around the supply pins and route each channel's feedback components close to the associated amplifier pins to reduce parasitic feedback and instability. Decoupling capacitors should be placed directly between each supply pin and ground. Because this is a non-rail-to-rail, bipolar general-purpose amplifier, input and output common-mode headroom must be checked against the actual supply voltages. This page combines verified manufacturer and distributor information, drop-in family alternatives, package and pinout details, application guidance, and design notes to provide more implementation context than the basic distributor catalog entry.

RFC Hubungi kami
MC1458PSR - Dual 30V 1MHz Op Amp | Texas Instruments (Tape & Reel)
MC1458PSR

MC1458PSR - Dual 30V 1MHz Op Amp | Texas Instruments (Tape & Reel)

The Texas Instruments MC1458PSR is a dual general-purpose operational amplifier with two internally compensated amplifier channels, a 30 V rating, and a 1 MHz gain-bandwidth product in an 8-pin SOIC package. The MC1458 family combines short-circuit protection, wide common-mode and differential input-voltage ranges, low power consumption, and latch-up-free operation. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to compare and amplify small voltage differences. The MC1458 belongs to the general-purpose operational-amplifier family within the broader analog IC and semiconductor hierarchy. Its two channels can operate independently for signal conditioning, voltage following, summing, integration, or other feedback-based amplifier configurations. Each MC1458 channel offers a 1 MHz gain-bandwidth product, 500 V/ms slew rate, and 90 dB common-mode rejection in the supplied product data. The reported input bias current is 1.5 µA, input offset current is 200 nA, and typical input offset voltage is 6 mV. Internal frequency compensation eliminates the need for external compensation components in the manufacturer's standard voltage-follower application. The MC1458 architecture is intended for general-purpose precision amplification rather than high-speed or rail-to-rail operation. Its wide common-mode input range makes it suitable for conventional bipolar-supply circuits, while the absence of latch-up improves robustness during power sequencing and input-overvoltage events. Short-circuit protection helps limit output current when an output is overloaded, although sustained short-circuit duration and internal current limits should be confirmed in the manufacturer datasheet. Typical uses include audio preamplification, summing amplifiers, active filters, sensor-signal conditioning, industrial control blocks, and general voltage-following circuits. Two amplifiers in one package can reduce component count and simplify dual-channel or differential signal-path layouts. The commercial MC1458PSR temperature grade is 0 °C to +70 °C, making it appropriate for room-temperature industrial and consumer equipment rather than exposed automotive or extreme-temperature installations. PCB design should reserve adequate copper around the supply pins and route each channel's feedback components close to the associated amplifier pins to reduce parasitic feedback and instability. Decoupling capacitors should be placed directly between each supply pin and ground. Because this is a non-rail-to-rail, bipolar general-purpose amplifier, input and output common-mode headroom must be checked against the actual supply voltages. This page combines verified manufacturer and distributor information, drop-in family alternatives, package and pinout details, application guidance, and design notes to provide more implementation context than the basic distributor catalog entry.

RFC Hubungi kami
MC14600P - Low-Power CMOS Alarm IC w/ Horn Driver | NXP DIP-16
MC14600P

MC14600P - Low-Power CMOS Alarm IC w/ Horn Driver | NXP DIP-16

The NXP MC14600P is a low-power CMOS alarm IC with integrated piezoelectric horn driver and LED driver, housed in a 16-pin DIP (through-hole) package. It is engineered to convert an analog alarm-level voltage condition into a tone output for a piezo horn and/or an LED indicator with extremely low average current draw, making it ideally suited to long-life battery-operated alarm systems. The part integrates a low-battery detection feature that monitors supply voltage and a minimal external RC network to configure its operating thresholds. An alarm IC is a specialized consumer circuit in the broader semiconductor family of alarm and supervisory ICs (alarm IC -> supervisory circuit -> power management IC). Its role in a system hierarchy is to sit between an analog sensor (smoke, gas, heat) or a manually triggered switch network and the audible/visual annunciation stage, removing the need for a microcontroller in single-function safety devices. The MC14600 sits at the low-power end of this family, distinct from microcontroller-based alarm SoCs and from generic buzzers or piezos. Key features include a low average current requirement optimized for battery life, integrated horn driver capable of directly driving a piezoelectric transducer or small speaker, an LED driver pin for visual indication of alarm state, an on-chip low-battery detection comparator with adjustable threshold via an external resistor divider, and CMOS construction for low quiescent drain. The alarm and low-battery detect inputs both have internal hysteresis to prevent false triggering. Only a handful of external passive components - typically an RC timing network, an input divider, and a piezo element - are required to form a complete alarm subsystem. Architecturally the device uses a CMOS analog and digital mixed-signal block: a precision voltage reference, two comparator channels (alarm input and low-battery input), a piezo tone generator, and output drivers capable of sourcing/sinking the piezo and LED loads. The low-battery detect logic shares the same internal reference as the alarm comparator, ensuring consistent behavior over temperature. The CMOS process and integrated drivers eliminate the need for an external transistor to drive the horn. Typical applications include standalone smoke detectors, gas-leak detectors, and personal-security panic alarms where low standby current is critical. Industrial equipment-monitoring alarm circuits, portable medical alarm devices, and battery-powered temperature or liquid-level alarms also benefit from this part. The wide operating temperature range supports both commercial and industrial environments. Design considerations focus on selecting the input-divider resistor values to match the chosen alarm sensor threshold, sizing the timing RC for the desired tone cadence, and ensuring the piezo element's voltage rating matches the device's horn-driver swing. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that go beyond the basic datasheet pinout table.

RFC Hubungi kami
MC1488D - Quad EIA-232D Driver | onsemi | RS-232 Interface
MC1488D

MC1488D - Quad EIA-232D Driver | onsemi | RS-232 Interface

The onsemi MC1488D is a monolithic four-channel EIA-232D line driver with a 14-pin SOIC package. It provides four current-limited differential outputs intended to interface data terminal equipment with data communications equipment, with typical output current limited to ±10 mA and a minimum power-off source impedance of 300 ohms. An EIA-232D line driver is a type of RS-232 interface driver that converts logic-level signals into the voltage-domain signals used by RS-232 communications equipment. Within the broader hierarchy, it is a line driver and interface IC within communications and power-management signal conditioning. Its four channels allow one package to support several unidirectional data paths when the system already provides the required receiver and supply circuitry. Key features include four independent driver channels, typical current-limited output of ±10 mA, and a minimum power-off source impedance of 300 ohms. The current limiting helps control output current when a receiver or connected circuit imposes an abnormal load. The MC1488D also provides simple slew-rate control, an important characteristic for reducing unwanted transitions on slow RS-232 links. Technically, the device is designed around the EIA-232D interface requirements identified in the onsemi datasheet. Because MC1488D contains drivers rather than receivers, it cannot replace a complete RS-232 transceiver without external receiver circuitry. In a typical interface, logic signals enter the driver inputs and leave through four EIA-232D output channels. The receiver and any required level translation are separate functions. Typical uses include legacy RS-232 ports, data terminal equipment, data communications equipment, industrial control interfaces, and embedded systems that retain an EIA-232D connection. The MC1488D is also useful as the transmit-side element in a multi-channel interface where a companion receiver IC is already present. Designers should verify the supported supply voltage, input thresholds, output levels, timing, and absolute maximum ratings directly against the manufacturer datasheet before implementation. PCB layout should preserve short output paths, provide an appropriate ground reference, and avoid placing sensitive analog signals beside the driver outputs. This page combines verified manufacturer and distributor information, source-backed drop-in candidates, interface-selection guidance, and practical PCB considerations to provide engineering context beyond a basic MC1488D catalog listing.

RFC Hubungi kami
MC1488DG - Quad EIA-232D Driver | onsemi | RS-232 Interface
MC1488DG

MC1488DG - Quad EIA-232D Driver | onsemi | RS-232 Interface

onsemi MC1488DG is a monolithic quad line driver designed to interface data terminal equipment with data communications equipment using the EIA-232D standard. The device provides four driver channels, operates from a 5 V supply, and uses a 14-pin SOIC package. Its typical output current is ±10 mA per channel, with current limiting built into the outputs. The MC1488DG is intended for RS-232 transmitter functions rather than receiver functions, so it must be paired with a suitable quad receiver when full bidirectional communication is required. An EIA-232D line driver is a type of interface transceiver component that converts logic-level signals into RS-232 voltage levels for transmission between data terminal equipment and data communications equipment. In the broader hierarchy, MC1488DG belongs to the interface IC category, specifically the RS-232 driver family. Its quad-channel architecture reduces the component count in systems requiring several serial data outputs while preserving the signal and power connection conventions established for EIA-232D equipment. The principal features of MC1488DG include four independent driver outputs, integrated output current limiting, and a typical output current capability of ±10 mA. The driver is designed for conformance with EIA-232D interface requirements, and its monolithic construction places the driver functions in one 14-pin SOIC package. The design supports equipment requiring multiple RS-232 transmit channels, including computer peripherals, industrial data links, test equipment, and legacy communications equipment. Technically, the MC1488 belongs to the family of bipolar RS-232 line drivers that use positive and negative supply rails to develop the bipolar voltage levels required by the interface standard. The MC1488 data also identifies SN55188 and SN75188 as related monolithic quadruple line drivers. Because MC1488DG is a driver-only device, engineers should check signal levels, supply requirements, output polarity, and protection needs against the original system interface before using it in a redesigned board. Typical applications include industrial serial-port controllers, laboratory instrumentation, point-of-sale terminals, data acquisition equipment, and embedded systems that retain an RS-232 output interface. In a multi-channel design, each logic input can drive a corresponding RS-232 output, while a separate receiver IC handles incoming signals. This separation is important because the MC1488 provides four transmit channels but no integrated receive channels. A key design consideration is to preserve the original board footprint and verify every pin assignment before substitution. The 14-pin SOIC package is suitable for conventional surface-mount assembly, but RS-232 cables connect to externally exposed connector pins rather than directly to the IC. External protection, grounding, connector geometry, and cable-routing decisions remain necessary to achieve reliable system-level communications. This page combines the verified manufacturer and distributor references for MC1488DG with package information, interface intent, sourcing links, and identified pin-compatible alternatives. It also distinguishes the driver-only MC1488DG from complete RS-232 transceiver functions, helping engineers select the correct replacement without confusing interface direction or package compatibility.

RFC Hubungi kami
MC1488DR2 - 4-Channel RS-232 Driver | onsemi | SOIC-14
MC1488DR2

MC1488DR2 - 4-Channel RS-232 Driver | onsemi | SOIC-14

The onsemi MC1488DR2 is a four-channel RS-232 line driver with no receiver channels, designed for EIA-232D data-terminal and data-communications interfaces. The device operates from dual positive and negative supplies of ±15 V, provides typical current-limited outputs of ±10 mA, and is packaged in a surface-mount 14-pin SOIC measuring 3.90 mm wide. An RS-232 line driver is a specialized interface-circuit component that converts logic-level signals from a digital system into the voltage levels required by an RS-232 communications port. The MC1488 family belongs to the broader line-driver and interface-IC hierarchy, where four independent driver channels can support multiple serial links, control signals, or communications ports within one package. Key features include four independent driver outputs, support for EIA-232D signaling, current limiting at approximately ±10 mA typical, and operation from ±15 V supplies. Its 14-SOIC surface-mount construction makes it suitable for compact communications and industrial-control equipment. Each channel provides a separate driver path, allowing multiple logic signals to be shifted into RS-232-compatible levels. The MC1488 uses separate positive and negative supply rails rather than a single low-voltage rail. This architecture is appropriate when the surrounding equipment already provides ±15 V or requires legacy RS-232 voltage levels. Board designers must account for the relationship between input logic levels, supply polarity, output current, and the load presented by the RS-232 interface. Typical applications include legacy RS-232 ports, data-terminal interfaces, industrial equipment connections, test systems, and embedded control panels. In these systems, the MC1488DR2 can convert four TTL or CMOS-compatible control signals into RS-232 levels while operating with standard ±15 V communications supplies. A critical design consideration is the need to observe supply sequencing and the limits of the RS-232 interface. Place bypass capacitors close to the supply pins, maintain short return paths, and confirm that the connected cable and receiver tolerate the driver’s output characteristics before finalizing the layout. This page organizes the MC1488DR2 specifications, sourcing information, drop-in candidates, and application guidance to support faster design review. Because the MC1488DR2 is identified as obsolete, lifecycle planning and verified alternate sourcing are especially important for new and maintenance designs.

RFC Hubungi kami
MC1488M - Quad EIA-232D Driver, SOIC-14 | onsemi
MC1488M

MC1488M - Quad EIA-232D Driver, SOIC-14 | onsemi

onsemi MC1488M is a monolithic quad line EIA-232D driver with four current-limited outputs, supplied in a 14-pin SOIC package. The device provides typical output currents of ±10 mA and a minimum power-off source impedance of 300 Ω. It is designed to interface data terminal equipment with data communications equipment using the EIA-232D signal convention. An EIA-232D line driver is a transmitter within the broader interface IC and RS-232 transceiver categories. Its role is to convert logic-level transmit signals into bipolar voltage levels suitable for EIA-232D communication links. The MC1488M contains four independent driver channels, allowing one package to support multiple serial-data outputs in equipment such as modems, computer interfaces, industrial communications equipment, and legacy peripheral systems. The principal features of the MC1488M include four driver channels, typical current-limited output capability of ±10 mA, a 300 Ω minimum power-off source impedance, and EIA-232D interface conformance. Its 14-pin SOIC package supports surface-mount PCB assembly while reducing the footprint required by a discrete transistor driver arrangement. The M suffix identifies the surface-mount ordering variant presented by onsemi. Internally, the MC1488M combines four line-driver stages with supply-voltage protection arrangements described in the associated device literature. Its monolithic construction provides a practical alternative to separate transistor or MOSFET driver circuits. Because the output stage is designed to source and sink current rather than operate as a logic-level CMOS output, the circuit should be evaluated as an EIA-232D interface stage, not as a general-purpose push-pull logic driver. Typical uses include four-channel RS-232 transmit ports, data terminal equipment, data communications equipment, printer interfaces, and industrial data links. Designers combining this driver with a receiver can construct a complete asymmetric RS-232 interface. The component is especially relevant to legacy systems that require more than two independently driven EIA-232D outputs while retaining a surface-mount footprint. The primary design consideration is the external interface network and supply arrangement. EIA-232D implementations commonly use series resistors and capacitive or diode-clamped protection to manage transient conditions, while supply bypassing must be placed close to the device. Engineers should also verify receiver compatibility, cable requirements, logic levels, and all electrical limits against the manufacturer datasheet before substituting the part into a live design. This product page consolidates the verified manufacturer and distributor information for MC1488M with package details, sourcing guidance, practical design notes, and a strict assessment of available drop-in alternatives. Where the supplied source material does not establish an exact same-package replacement, the page identifies that limitation instead of presenting an unverified substitution as drop-in compatible.

RFC Hubungi kami
MC1488MEL - Quad EIA-232D Driver | onsemi
MC1488MEL

MC1488MEL - Quad EIA-232D Driver | onsemi

The onsemi MC1488MEL is a monolithic quad line driver designed to interface data terminal equipment with data communications equipment in accordance with EIA-232D requirements. The device provides four independent driver channels and is specified for operation with ±15 V supply voltages. It is packaged in the onsemi SOEIAJ-14, a 14-pin small-outline surface-mount package with a 5.30 mm package width. A line driver is an interface IC that converts low-voltage logic signals into differential, bipolar RS-232-style voltage levels for transmission over a serial communication link. In the broader hierarchy, the MC1488MEL belongs to the RS-232 driver and receiver family, within interface ICs and data-communication semiconductors. Its four channels allow one package to support multiple unidirectional serial lines, reducing board area compared with separate single-channel drivers. The principal feature of the MC1488MEL is its quad EIA-232D line-driver architecture. The manufacturer describes the MC1488 as a monolithic quad line driver with current-limited outputs and an operating supply arrangement of approximately ±15 V. This architecture is useful when a system needs to translate TTL or CMOS-side control signals into the voltage levels expected by an RS-232 interface, particularly where multiple unidirectional channels are required. The MC1488MEL is specified for commercial-extended temperature-grade applications. Its 14-terminal surface-mount construction is intended for automated PCB assembly and compact equipment designs. The package is identified as SOEIAJ-14 rather than a generic 14-pin SOIC designation, so engineers should use the manufacturer pin configuration and land pattern associated with that specific package when laying out a replacement board. Typical uses include industrial control equipment, data-terminal interfaces, RS-232 communication ports, peripheral connections, and legacy serial-control systems. Because it is a driver rather than a combined transceiver, the application must provide a separate receiver when a complete bidirectional RS-232 port is required. Review signal polarity, supply sequencing, cable routing, and grounding before using the device in a new design. For power planning, use the datasheet’s absolute-maximum and recommended operating conditions rather than assuming that ±15 V is the only acceptable implementation. The device’s output stage is intended for current-limited RS-232 driver operation, but the PCB still needs appropriate supply decoupling and controlled return paths. This page focuses on the MC1488MEL’s function, package, interface role, and replacement considerations.

RFC Hubungi kami
MC1488MG - Quad EIA-232D Driver | onsemi | RS-232
MC1488MG

MC1488MG - Quad EIA-232D Driver | onsemi | RS-232

The onsemi MC1488MG is a monolithic four-channel RS-232 line driver with a 4/0 driver-to-receiver configuration, current-limited outputs rated at ±10 mA typical, and a 14-pin gull-wing SOIC package. It is designed for data-terminal equipment and data-communications equipment that require an EIA-232D-compatible transmit interface. The MC1488MG is identified as the commercial extended-temperature grade in distributor and catalog records. An RS-232 line driver is an interface IC that converts digital logic-level signals into unbalanced, bipolar voltage levels suitable for serial data links. Within the signal-chain hierarchy, it belongs to the RS-232 interface-driver family, combines with an RS-232 receiver to form a complete communications path, and ultimately provides the physical-layer function required between data terminal equipment and data communications equipment. Unlike a transceiver, the MC1488MG provides four driver channels and no receiver channels. The primary verified characteristics are four independently available line-driver outputs, EIA-232D conformance, typical current limiting of ±10 mA, a 14-pin SOIC package with gull-wing leads, and a commercial extended temperature grade. The output current limit protects the driver stage when a connected RS-232 line is shorted or misconfigured. Because four transmit channels are provided, one device can support four RS-232 outputs while reducing the number of external line-driver packages required. The MC1488MG is intended for legacy and industrial serial-control equipment where EIA-232D signaling remains required. Appropriate uses include multi-port controller interfaces, equipment test systems, point-to-point serial links, and control panels. The device requires suitable bypass capacitance and careful grounding because the implemented system also depends on cable characteristics, receiver thresholds, protection networks, and the voltage levels allowed by the selected RS-232 endpoint. For new designs, engineers should verify signal polarity, baud rate, logic thresholds, and electrical limits against the current manufacturer datasheet before layout release. The supplied search results confirm the EIA-232D driver function, four-output organization, ±10 mA typical output current, and 14-pin SOIC format, but several detailed timing, voltage, temperature, and absolute-maximum values were not included in the retrieved records. This page combines verified distributor and manufacturer-linked information, structured technical context, pin-compatible replacement guidance, and practical sourcing notes. It also separates confirmed electrical facts from parameters that require datasheet verification, helping engineers avoid assigning unsupported specifications to this legacy-compatible RS-232 interface device.

RFC Hubungi kami
MC1488N - Quadruple RS-232 Line Driver | Texas Instruments
MC1488N

MC1488N - Quadruple RS-232 Line Driver | Texas Instruments

Texas Instruments MC1488N is a monolithic quadruple RS-232 line driver with four driver channels, 10 mA typical current-limited output, and a minimum 300 ohm power-off output impedance. Designed for data-terminal equipment and data-communications equipment interfaces, the device operates from a 5 V supply in a 14-pin PDIP package rated for 0 to 70 degrees C. A line driver is a digital interface circuit that converts low-voltage logic signals into RS-232-compatible voltage levels. The MC1488 belongs to the RS-232 driver hierarchy, where a line driver interfaces data-terminal equipment with data-communications equipment. Its four channels allow one package to support four unidirectional serial data paths, reducing component count in multi-port or multi-channel RS-232 equipment. The device is designed to meet or exceed ANSI EIA/TIA-232-E and ITU Recommendation V.28 requirements. According to the Texas Instruments manufacturer datasheet, each output includes current limiting, and the power-off output impedance is at least 300 ohms. A series diode is used at each supply-voltage terminal, while the output slew rate can be controlled through the load capacitance connected to each driver. The MC1488N is designed to be interchangeable with the Motorola MC1488, which supports PCB sourcing flexibility where the original function is required. The manufacturer datasheet identifies the MC1488, SN55188, and SN75188 as monolithic quadruple line drivers, but device ordering suffixes, temperature ranges, and package variants must still be checked before substitution. The N suffix identifies the 14-pin PDIP configuration shown in the verified Texas Instruments part-details data. Typical uses include RS-232 interfaces in data-terminal equipment, data-communications equipment, industrial control systems, point-of-sale equipment, printers, and legacy serial-port adapters. It is particularly useful where multiple RS-232 channels share a common logic interface and a through-hole package is preferred for serviceability or manual assembly. PCB layout should keep each driver output away from sensitive analog and high-speed digital traces because RS-232 transitions can produce edge-related EMI. The data input pins must be driven only when the supply is valid, and unused outputs should be handled according to the manufacturer datasheet rather than left as floating high-impedance nodes. Confirm output polarity and logic levels before interchanging it with a receive/transceiver device.

RFC Hubungi kami
MC1488NE4 - Quad RS-232 Line Driver 300kbps | Texas Instruments
MC1488NE4

MC1488NE4 - Quad RS-232 Line Driver 300kbps | Texas Instruments

The Texas Instruments MC1488NE4 is a quadruple RS-232 line driver with four independent drivers rated for data rates up to 300 kb/s, operating from dual supplies of 7.5 V to 15 V (positive) and the matching negative rail, in a 14-pin PDIP (N) package. A line driver is an interface IC that converts low-voltage logic-level signals from a UART or microcontroller into the larger voltage swings required by the EIA/TIA-232 (RS-232) serial communication standard. Within the signal-chain hierarchy, it sits between the digital controller and the physical serial cable, and forms a driver-receiver pair with companion parts such as the MC1489 quadruple line receiver. RS-232 remains common in industrial equipment, point-of-sale terminals, and legacy instrumentation despite newer USB and Ethernet links. The MC1488NE4 provides four drivers in one package, each with TTL/CMOS-compatible inputs and RS-232-level outputs. Output signal swing is set by the supply rails, allowing engineers to tailor output levels via the positive and negative supplies. Typical output current capability supports driving standard RS-232 cable capacitance at data rates up to 300 kb/s, per the manufacturer datasheet. The N suffix package is molded PDIP, suited to through-hole prototypes and repair of legacy boards. Architecturally, the part uses a monolithic bipolar process. Each driver contains ainput stage, phase-splitting stage, and output structure referenced between the two supply rails, producing output swings that meet EIA-232-E voltage requirements when supplies are appropriately chosen. Series elements at the supply terminals are used in the manufacturer's typical application to improve robustness. Typical applications include UART-to-RS-232 conversion in industrial terminals, modem and DTE-to-DCE interfacing, programming and debugging ports on legacy equipment, and educational/lab serial circuits. It pairs naturally with the MC1489 or DS1489 receiver on the far end of the link. Design consideration: the MC1488 requires both a positive and a negative supply rail - systems lacking a negative rail need a charge-pump converter such as the MAX232 family or ICL232, which integrate the voltage generation. Also verify power dissipation with multiple drivers switching simultaneously. This page adds value beyond the manufacturer datasheet by synthesizing drop-in alternative cross-references (DS14C88, SN75188, SN75C188), comparison tables, and practical design notes in one place for sourcing and design engineers.

RFC Hubungi kami
MC1488NG4 - Quad RS-232 Line Driver | Texas Instruments
MC1488NG4

MC1488NG4 - Quad RS-232 Line Driver | Texas Instruments

Texas Instruments MC1488NG4 is a monolithic quadruple RS-232 line driver containing four driver channels and no receiver channels in a 14-pin PDIP package. It is designed for data-terminal equipment interfacing with data-communications equipment in conformance with ANSI TIA/EIA-232-E. The device uses a diode in series with each supply-voltage terminal in the application configuration described by the manufacturer. An RS-232 line driver is an interface IC that converts logic-level signals into bipolar voltage levels suitable for RS-232 communications. Within the interface hierarchy, the MC1488 belongs to the line-driver and transceiver class, where a transmitter handles outbound data and a receiver handles inbound data. Because the MC1488 provides four drivers and no receivers, a complete communication channel generally requires a separate receiver IC and the associated interface protection. The primary feature of the MC1488NG4 is its four-driver organization in one 14-pin PDIP package. Four channels allow one driver IC to support multiple RS-232 outputs while reducing the number of external packages and board-space requirements. The device is specifically identified as a 4/0 RS-232 driver, meaning that it offers four driver functions and zero receiver functions. It is also associated with the MC1488, SN55188, and SN75188 device family in the manufacturer documentation. The MC1488 architecture uses current-limited driver outputs suited to interfaced RS-232 lines. In the documented typical application, a diode is placed in series with each supply-voltage terminal, allowing the supply arrangement to suit the system polarity and interface requirements. Designers should preserve that topology, validate output-level behavior with the intended cables and loads, and review the complete manufacturer datasheet before releasing a new layout. Typical uses include multi-port RS-232 equipment, data-terminal interfaces, industrial control panels, legacy data-collection systems, and communications equipment requiring several unidirectional outputs. The MC1488 can also be paired with a quad receiver such as the MC1489 family to create a complete differential-direction RS-232 interface on a board that still uses through-hole integrated circuits. PCB planning should allow the 14-pin PDIP to be installed without pin-1 errors, and signal-routing should keep driver outputs away from sensitive analog or high-speed digital traces. Adequate bypass capacitance and grounding remain essential for stable operation. The actual electrical limits, output-current behavior, supply range, temperature range, and timing or transition characteristics must be checked against the manufacturer datasheet before design sign-off. This product page consolidates the identified RS-232 functionality, package information, datasheet access, compatible interface-family options, and practical implementation guidance. It also distinguishes a genuine same-package line-driver alternative from receiver ICs, which may complement the MC1488NG4 but cannot replace its four driver outputs.

RFC Hubungi kami
MC1488P - Quad RS-232 Line Driver | STMicroelectronics
MC1488P

MC1488P - Quad RS-232 Line Driver | STMicroelectronics

The STMicroelectronics MC1488P is a monolithic quadruple RS-232 line driver with four differential driver channels in a 14-pin PDIP package. According to the verified manufacturer and distributor information, the device is intended to interface data terminal equipment with data communications equipment under EIA RS-232C and EIA-232D requirements. Its outputs are current limited to ±10 mA typical, while the power-off source impedance is specified at 300 ohms minimum. These characteristics make the MC1488P suitable for legacy RS-232 equipment requiring four unidirectional data channels, especially systems built around the classic MC1488 interface family. A line driver is a digital interface component that converts TTL-compatible logic signals into voltage levels suitable for a balanced or unbalanced communications link. In the broader electronics hierarchy, the MC1488P belongs to interface ICs, specifically the RS-232 driver category. It complements receiver ICs such as the MC1489 rather than operating as a complete bidirectional transceiver. Each of its four channels therefore supports one driven signal path per package. The principal verified features are the monolithic four-channel implementation, RS-232 interface purpose, ±10 mA typical current-limited outputs, 300 ohms minimum power-off source impedance, and 14-pin PDIP construction. The DigiKey listing identifies the device as a 4/0 RS-232 driver in a 14-DIP package, while Mouser categorizes it as a quad line driver. These are legacy communications characteristics rather than modern high-speed differential-interface specifications. The MC1488P is normally powered from separate positive and negative supply rails so that its output stage can generate RS-232 voltage levels from low-voltage logic. Exact supply limits, propagation delay, output-voltage levels, operating temperature, and absolute maximum ratings are not included in the supplied search records, so those values must be verified against the original manufacturer datasheet before a new design is released. The MC1488P may also need external charge-pump circuitry when used with modern single-supply systems because it does not include an on-chip RS-232 voltage converter. Typical uses include legacy serial-port adapters, industrial data-collection equipment, point-of-sale terminals, laboratory interfaces, and controller boards that exchange RS-232 signals with older peripherals. In each case, the MC1488P handles the transmit side, while a compatible receiver handles incoming signals. Software handshaking, ground continuity, and protection against external cable transients remain important system-level considerations. Designers should preserve the original 14-pin footprint and verify pin functions, supply rails, and logic thresholds against the applicable datasheet. Decoupling capacitors should be placed close to the supply pins, and cable-side protection may be required for industrial environments. Because the verified sources identify both STMicroelectronics and onsemi offerings, purchasing decisions should also account for manufacturer traceability, lifecycle status, and approved-source documentation. This page consolidates the verified RS-232 line-driver description, distributor identification, package information, drop-in substitution evidence, and practical design considerations into one engineering-focused reference. It also distinguishes verified facts from specifications that still require confirmation from the complete manufacturer datasheet.

RFC Hubungi kami
MC1488PG - Quad RS-232 Line Driver | onsemi | PDIP-14
MC1488PG

MC1488PG - Quad RS-232 Line Driver | onsemi | PDIP-14

The onsemi MC1488PG is a monolithic quadruple RS-232 line driver with four driver outputs, designed for EIA-232D data-terminal and data-communications equipment interfaces. The device operates from a single positive supply, provides current-limited outputs with a typical ±10 mA output capability, and is packaged in a 14-pin PDIP format. Its four independent channels allow one interface IC to drive four RS-232 data signals while reducing the number of packages required on a communications board. An RS-232 line driver is a digital interface component that converts TTL-compatible logic levels into bipolar voltage levels suitable for transmission over an RS-232 port. A line driver belongs to the broader interface IC hierarchy and works alongside line receivers, transceivers, and protection devices in the wider data-communications and industrial-control equipment category. The MC1488 therefore provides the transmit-side function in a conventional RS-232 interface, while a separate receiver is required for incoming signals. Key features include four driver channels in one monolithic package and current-limited outputs rated to ±10 mA typical. The MC1488PG is associated with EIA-232D interface requirements and uses a 14-pin PDIP package for through-hole PCB assembly. These characteristics make it suitable for legacy computer ports, industrial control links, embedded serial equipment, and other systems that continue to use the bipolar RS-232 physical interface. The four driver outputs allow several communications lines to share the same supply and package, reducing PCB component count compared with discrete single-channel driver designs. Because the outputs are current limited, the device is suited to driving conventional RS-232 loads rather than high-current or long-distance cable networks. Designers should still provide the required bypass capacitance, observe the supply-voltage limits, and verify receiver and cable characteristics at the system level. Typical applications include multi-channel RS-232 equipment interfaces, legacy PC communication ports, test instruments, point-to-point industrial serial links, and embedded control systems. The four-channel arrangement is particularly useful when a board must transmit several RS-232 signals through a single interface package. A complementary receiver, such as a compatible RS-232 receiver IC, is required when the same port must also receive data. For a new PCB, confirm the manufacturer's MC1488 datasheet for the exact pin assignment, supply limits, output-current conditions, and decoupling recommendations. For an existing board, verify footprint, pinout, logic polarity, and operating-voltage compatibility before substitution, especially when the assembly includes protection networks or unusual cable loading. This product page combines the MC1488PG device identity, RS-232 design considerations, drop-in replacement guidance, and practical application context to help engineers evaluate legacy-interface repair, modernization, and sourcing decisions without relying on a raw catalog listing.

RFC Hubungi kami
MC1489AD - Quad EIA-232D Receiver IC | onsemi
MC1489AD

MC1489AD - Quad EIA-232D Receiver IC | onsemi

onsemi MC1489AD is a monolithic quad line receiver designed to connect data terminal equipment with data communications equipment conforming to EIA-232D. The device contains four receivers in a 14-pin SOIC package and is identified by the DigiKey listing as a 0/4 RS-232 receiver. According to the onsemi datasheet, its input resistance is specified from 3.0 kΩ to 7.0 kΩ. An EIA-232D line receiver is a type of interface IC that converts bipolar serial data from a communications port into a digital logic signal for a host, peripheral, or data-processing system. The receiver belongs to the RS-232 interface hierarchy, which connects equipment using the EIA-232D electrical standard. A quad receiver consolidates four receive channels into one package, reducing board area and simplifying multi-port or multi-peripheral serial interfaces. The MC1489AD is intended for systems in which external equipment presents EIA-232D signals to the receiving circuit. Its four-channel arrangement is useful for control consoles, communications equipment, industrial peripherals, and legacy data-terminal interfaces. The specified input resistance helps define the loading placed on the signal source, while the integrated receiver channels reduce the number of discrete interface components required at the system boundary. Because this device receives rather than transmits EIA-232D signals, it does not perform the voltage conversion normally assigned to an RS-232 driver. Designers must pair it with the appropriate line-driver circuitry when a design requires bidirectional serial communication. Likewise, the application schematic must observe the polarity, voltage levels, and timing requirements of the connected EIA-232D interface rather than treating the receiver inputs as ordinary CMOS inputs. The principal design consideration is verifying that the PCB land pattern and pin assignments match the 14-pin SOIC ordering of the MC1489AD. The package suffix identifies a surface-mount variant, but the complete numbered pin list must be taken from the manufacturer pin-description table before tracks are assigned. Signal routing should keep the receive paths away from noisy switching nodes, and unused receiver channels should be configured according to the datasheet rather than left open without guidance. Typical implementations include industrial serial consoles, data-terminal equipment, communications interfaces, test systems, and embedded systems that must acquire EIA-232D data from external equipment. The principal trade-off is its specialized interface purpose: it addresses legacy or long-established EIA-232D links but does not replace modern differential buses such as RS-422 or RS-485. This product page organizes the MC1489AD’s confirmed electrical characteristics, package information, cross-reference considerations, and application guidance. It also distinguishes genuine pin-compatible replacements from electrically similar parts that use a different package or pin arrangement, helping engineers avoid a substitution that compiles but cannot be soldered onto the original footprint.

RFC Hubungi kami
MC1489AM - Quad EIA-232D Receiver | onsemi | SOIC-14
MC1489AM

MC1489AM - Quad EIA-232D Receiver | onsemi | SOIC-14

onsemi MC1489AM is a monolithic quad line receiver designed to interface data terminal equipment with data communications equipment conforming to EIA-232D. The device combines four receiver channels in a 14-pin SOIC package, with an input resistance specified from 3.0 kΩ to 7.0 kΩ and an input signal range extending to 30 V. It is intended for systems that receive bipolar RS-232 signals and translate them into logic-level signals for the receiving equipment. The MC1489AM is a receiver-only device rather than a combined RS-232 transceiver. An EIA-232D line receiver belongs to the interface IC hierarchy, where it sits between a physical communication port and digital logic. RS-232 uses single-ended bipolar signaling, so a receiver must identify valid positive and negative voltages while rejecting signals outside the accepted logic thresholds. The four independent channels of the MC1489AM allow one package to handle four serial ports, four peripheral connections, or several control signals carrying the same receiver electrical characteristics. The primary electrical feature is its 3.0 kΩ to 7.0 kΩ input resistance. This relatively high impedance limits loading on the transmitting side and is useful when several receiver inputs must observe a signal source. The 30 V input signal range provides tolerance for voltage excursions on the physical line. Because the package contains four channels, it also reduces component count and board space compared with four separate single-channel receiver packages. The MC1489AM is specifically identified as an EIA-232D receiver rather than a modern transceiver with integrated charge-pump voltage generation. In a complete RS-232 interface, the MC1489AM is used on the receive path, while a separate line driver handles the transmit path. This separation can be advantageous in asymmetric equipment, test systems, industrial controllers, and legacy installations where the number of transmitted and received signals differs substantially. Common applications include industrial serial-port interfaces, data terminal equipment, data communications equipment, peripheral controllers, instrumentation, and legacy computer equipment. Designers should provide the interface system with an appropriate common reference and route the receive outputs directly into the receiving logic or level-shifting circuitry required by the host device. When laying out a circuit using the MC1489AM, keep the receiver close to the connector or protected signal entry point to minimize the distance over which unprotected RS-232 signals can pick up noise. The input network should avoid excessive loading because the receiver input resistance can vary across the stated 3.0 kΩ to 7.0 kΩ range. Confirm the complete pin assignment, voltage limits, and system enable requirements against the manufacturer datasheet before fabrication. This product page combines the verified device identity, package information, and electrical characteristics with application guidance, design considerations, and a conservative drop-in replacement assessment. It is structured to help engineers identify the correct receiver function, plan the interface architecture, and avoid treating functionally similar receivers as pin-compatible replacements.

RFC Hubungi kami
MC1489AMG - Quad EIA-232D Receiver | onsemi | RS-232
MC1489AMG

MC1489AMG - Quad EIA-232D Receiver | onsemi | RS-232

The onsemi MC1489AMG is a monolithic quad line receiver designed to connect data terminal equipment with data communications equipment conforming to EIA-232D. It provides four receiver channels in a 14-pin SOIC package, with an input resistance of 3.0 kΩ to 7.0 kΩ and an input signal range of ±30 V. The component is intended for receiving bipolar RS-232 signals in multi-channel serial-interface systems. A quad line receiver is an interface IC that converts bipolar RS-232 voltage levels into complementary TTL-compatible logic signals. In the hierarchy of electronic components, it belongs to the line-receiver class, then interface IC, then digital interface and communication semiconductor. The MC1489 family is designed for equipment in which multiple data or control channels must be received from a single 14-pin package. The primary features of the MC1489AMG are its four independent EIA-232D receiver channels, broad input signal range, and moderate input resistance. The ±30 V input capability provides tolerance for the voltage excursions associated with RS-232 communication links, while the 3.0 kΩ to 7.0 kΩ input resistance provides the loading behavior expected by the interface circuit. The commercial extended temperature grade identifies its intended operating environment. Each receiver accepts a differential-looking pair of RS-232-related input pins and produces a corresponding logic output. Integrating four channels reduces the number of packages and interconnections needed for multi-port systems. The MC1489AMG contains receivers only; it does not provide the voltage-level translation used to transmit RS-232 signals, so a complementary line-driver device is required when a design needs both transmission and reception. Typical uses include industrial data acquisition, point-of-sale equipment, serial adapters, test instruments, and embedded systems that receive multiple RS-232 channels. The 14-pin SOIC package is appropriate for conventional through-hole or mixed-technology PCB assembly. Because an RS-232 receiver does not terminate or protect a physical cable, systems still require suitable cable routing, grounding, surge protection, and interface-level consideration. A key design practice is to verify the complete MC1489 pin description and typical application circuit in the onsemi datasheet before assigning board nets. Keep the RS-232 input traces away from clocks, fast digital signals, and switching-power-node areas. Provide a stable supply reference for the logic side of the interface and place any required bypass capacitance close to the device supply pins. This page combines the manufacturer interface definition, package and electrical characteristics, drop-in alternatives, application guidance, and PCB-oriented design notes. These resources help engineers distinguish a true pin-compatible receiver from a merely similar RS-232 transceiver and plan a board revision with fewer interface-integration risks.

RFC Hubungi kami
MC1489AN - Quad RS-232 Receiver, 5V, 14-PDIP | Texas Instruments
MC1489AN

MC1489AN - Quad RS-232 Receiver, 5V, 14-PDIP | Texas Instruments

The Texas Instruments MC1489AN is a quadruple RS-232 line receiver integrated circuit with four independent receiver channels, a 4.5 V to 5.5 V single supply, and a 14-pin PDIP package. Its stated input resistance is 7 kΩ, while the receiver supports input signal voltages up to 30 V. Each channel includes double-threshold input hysteresis and an external response-control connection that provides input-threshold shifting and noise filtering. A line receiver is an interface IC that converts bipolar RS-232 signals into logic-level digital signals. In the signal hierarchy, an RS-232 line receiver belongs to the broader category of interface ICs, communication transceivers, and data-conversion devices. The MC1489AN is intended specifically for the receiver side of a data-terminal-equipment to data-communication-equipment interface, where one connector may carry several low-speed serial signals and the cable may introduce threshold noise or unwanted voltage excursions. The principal feature of the MC1489AN is its four-channel integration in one 14-pin PDIP. Each receiver can be associated with a response-control terminal, allowing the design to tune threshold behavior and rejection of input noise. The built-in hysteresis gives the digital output a defined switching interval, reducing uncertainty when a slow or noisy input crosses the detection threshold. The receiver architecture is based on low-power Schottky technology and operates from one 5 V supply. According to the manufacturer datasheet, the MC1489AN is designed to meet or exceed the requirements of the TIA/EIA-232-F interface standard. Its 7 kΩ input resistance helps limit loading on the transmitting side, and its specified input-signal range extends to 30 V. These characteristics make it suitable for legacy RS-232 equipment, multi-port data acquisition interfaces, industrial control links, and equipment that must retain compatibility with established D-sub serial interfaces. The MC1489AN is most useful when a board needs more than one receive channel without allocating a separate single-channel receiver package to every port. Typical uses include four-wire industrial serial links, legacy printer interfaces, service-console connections, and test equipment. Because it is a receiver rather than a complete transceiver, the design must provide a separate line driver for each direction that requires transmission. Designers should review the complete pinout and recommended circuit before layout because the response-control terminals and input protection structure influence signal behavior. Place the receiver close to the connector or protected interface boundary, maintain the specified bypass capacitance, and route high-voltage or externally accessible receive lines away from sensitive logic. The verified public search results also identify a comparison with DS14C89AN/NOPB, which uses lower-power CMOS technology, but the complete device-specific values are not present in the supplied data. This page combines verified manufacturer and distributor information with package-level alternatives, application guidance, and design considerations. It distinguishes directly cited characteristics from unavailable specifications, helping engineers evaluate the MC1489AN without treating search-result summaries as complete datasheet data.

RFC Hubungi kami
MC1489AP - Quad RS-232 Receiver | STMicroelectronics
MC1489AP

MC1489AP - Quad RS-232 Receiver | STMicroelectronics

STMicroelectronics MC1489AP is a monolithic quad line receiver designed for RS-232 data-terminal and data-communication interfaces, with four receiver channels in a 14-pin DIP package. The device provides a 3.0 kΩ to 7.0 kΩ input resistance, low-power Schottky construction, and a separate response-control terminal for each receiver. It is associated with the TIA/EIA-232-F interface standard and is also described as supporting RS-232C and EIA-232-D requirements. An RS-232 receiver is a line-interface component that converts bipolar serial data arriving at a communications port into logic-level signals for a digital system. The MC1489AP belongs to the line-receiver hierarchy within interface ICs and combines four channels in one package. Its response-control terminals allow each input stage to be configured with external resistors or a resistor and bias-voltage source, giving the designer control over operating thresholds and system behavior. The quad-channel architecture reduces component count on equipment requiring multiple serial ports or several control links. Its specified input resistance of 3.0 kΩ to 7.0 kΩ is important when designing cable termination, biasing, and logic-threshold networks. The separate response-control terminals are the principal functional feature distinguishing this receiver family from simpler integrated transceivers that package fixed driver and receiver functions together. The MC1489AP is based on low-power Schottky line-receiver circuitry. According to the available manufacturer descriptions, the monolithic design was intended to satisfy the interface requirements between data-terminal equipment and data-communication equipment under EIA and TIA/EIA RS-232 definitions. Because each channel includes its own response-control connection, the external network must be selected with the system voltage, signal polarity, and desired threshold in mind rather than treated as a fixed internal configuration. Typical uses include industrial data acquisition, legacy peripheral interfaces, serial-control equipment, instrumentation, and embedded systems that retain RS-232 ports. The device is also useful when four independent receive channels can share a common logic supply and ground arrangement. Its DIP-14 format is appropriate for through-hole legacy designs, although modern compact products generally favor surface-mount interface ICs. For reliable implementation, verify the receiver supply voltage, input voltage limits, logic thresholds, and response-control network against the complete MC1489AP datasheet before layout release. Decoupling and grounding remain important because an RS-232 receiver may be positioned near a noisy cable entry point even though it is not the transmitter. Keep input and control networks away from switching nodes and use a stable, low-impedance ground reference to minimize threshold shifts. This product page combines verified manufacturer and distributor facts with same-package alternatives, parameter-level comparison data, and practical implementation guidance. It also distinguishes confirmed MC1489AP characteristics from parameters that require confirmation from the complete datasheet, helping engineers evaluate this legacy RS-232 interface device without relying on unsupported assumptions.

RFC Hubungi kami
MC1489APG - Quad RS-232 Receiver | onsemi | 14-DIP
MC1489APG

MC1489APG - Quad RS-232 Receiver | onsemi | 14-DIP

The onsemi MC1489APG is a monolithic quad line receiver designed for RS-232 data-terminal and data-communications interfaces. It contains four independent receiver channels in a 14-pin plastic dual in-line package (14-PDIP). According to the MC1489 datasheet, the device supports an input signal range of 30 V and an input resistance of 7.0 kΩ, making it suitable for receiving bipolar RS-232 signals after the transmitter has performed signal-level translation. An RS-232 receiver is an interface integrated circuit that converts the voltage-domain signals used by RS-232 links into logic-level signals suitable for digital equipment. The MC1489 belongs to the broader interface IC hierarchy: RS-232 receiver, line receiver, logic interface, interface IC, and semiconductor. Its four-channel arrangement allows one package to receive four data or control signals, reducing component count in multi-channel equipment. The confirmed features of the MC1489APG include its monolithic quad-receiver construction, EIA-232D interface application, 7.0 kΩ input resistance, 30 V input signal range, and 14-PDIP package. Each receiver is intended to handle the voltage levels associated with RS-232 rather than modern low-voltage CMOS interface signals. The receiver therefore complements an RS-232 line driver rather than replacing one. The architecture separates receive-side thresholding from the external transmission medium. In a typical RS-232 link, the transmitter converts TTL or CMOS logic into bipolar line voltage, while the MC1489APG receives those line voltages and converts them into usable logic-level outputs. This division allows equipment to use a separate transmitter and receiver for full-duplex serial communication, with the receiver section suitable for computer, terminal, and industrial serial-interface equipment. Typical applications include multi-channel RS-232 ports, data-terminal equipment, computer serial interfaces, industrial control links, and embedded systems that retain EIA-232D connections. In a design using the companion MC1488 line driver, the MC1489APG can receive up to four incoming signals while the MC1488 handles four outgoing signals. Cable routing and signal-return practices remain important because long unshielded RS-232 paths can pick up noise and introduce ground offsets. When laying out a board around the MC1489APG, reserve the complete 14-pin footprint and provide a ground return path for every transmitted signal where practical. Keep input and output traces away from high-current switching nodes and analog power stages. Confirm connector pin assignments, logic polarity, and system grounding before connecting external equipment because reversing interface signals or failing to establish a common ground can damage a receiver input. This product page combines the confirmed MC1489APG interface and package information, same-family replacement analysis, application guidance, and a parameter-by-parameter comparison. It is intended to help engineers confirm footprint compatibility and determine whether the receiver is appropriate for an RS-232 design.

RFC Hubungi kami
MC1489D - Quad EIA-232D Line Receiver | onsemi | SOIC-14
MC1489D

MC1489D - Quad EIA-232D Line Receiver | onsemi | SOIC-14

The onsemi MC1489D is a monolithic quad EIA-232D line receiver that converts four differential or bipolar serial data inputs into four compatible logic-level receiver outputs. Its 14-pin SOIC package, 3.0 kΩ to 7.0 kΩ input resistance, and approximately ±30 V input signal range support legacy RS-232 equipment interfaces. The MC1489D is designed for data terminal equipment and data communications equipment operating in conformance with EIA Standard EIA-232D. A line receiver, also called an RS-232 receiver, is an interface IC that recovers digital data from a ±3 V to ±15 V RS-232 signal while rejecting the common-mode voltage present on long cables. Within the interface hierarchy, the MC1489D belongs to the receiver subset of RS-232 line drivers and receivers, which sits inside the broader class of interface ICs and communication transceivers. A receive-only device is useful when the system already provides a separate transmitter, such as the MC1458D or MAX232DR. The headline characteristics of the MC1489D are its four-channel receiver architecture, 3.0 kΩ to 7.0 kΩ input resistance, and approximately ±30 V input signal capability. Each receiver provides threshold control that can accommodate both positive- and negative-going RS-232 signals. The monolithic construction reduces the external component count compared with discrete transistor receiver networks, while the 14-lead SOIC package simplifies assembly in legacy communications equipment. Operationally, the MC1489D accepts bipolar line signals and produces a logic-level indication of the signal state. The receiver input resistance limits current drawn from the RS-232 driver and influences the termination and biasing network selected by the system designer. Because the MC1489D implements EIA-232D rather than the later EIA-232-F revision, designers should verify that its electrical limits match the exact cable, driver, and system requirements rather than assuming interchangeability with every modern RS-232 controller. Typical uses include legacy terminal adapters, printer and workstation interfaces, industrial data acquisition, test equipment, and communication links that retain an MC1489-family receiver. It is particularly appropriate where four receive channels are needed in a single package and where the incoming signal can exceed the logic-level swing accepted by a CMOS or TTL input. The primary design consideration is to verify the receiver threshold network, exposed supply limitations, and available pin data against the exact manufacturer datasheet revision before layout. Because the provided source data does not enumerate a complete MC1489D pin table or maximum supply rating, those values should be confirmed before a new PCB is released. This page combines the verified onsemi and distributor sources with engineering guidance on RS-232 receiver selection, interface thresholds, legacy compatibility, and available drop-in alternatives. It also separates documented specifications from unverified parameters so procurement and design decisions are based on traceable evidence.

RFC Hubungi kami
MC1489DG - Quad EIA-232D Line Receiver | onsemi
MC1489DG

MC1489DG - Quad EIA-232D Line Receiver | onsemi

onsemi MC1489DG is a monolithic quad line receiver designed for EIA-232D data-terminal and data-communications interfaces. The device contains four receiver channels, accepts input signals ranging to plus or minus 30 V, and provides an input resistance of 3.0 kOhm to 7.0 kOhm. It is packaged in a 14-pin SOIC measuring approximately 3.90 mm wide with 0.154 inch lead pitch. An EIA-232D line receiver is an interface circuit that converts bipolar RS-232 signals into digital logic levels. It belongs to the receiver category within the broader RS-232 interface IC family. Because RS-232 uses voltage levels and signal conventions that differ from TTL and CMOS logic, a receiver is required between a physical communications port and the digital electronics that process the data. The MC1489DG's four independent receiver sections allow one package to serve several communications channels or several distinct RS-232 ports. Its plus or minus 30 V input signal range provides margin for the voltage excursions encountered in EIA-232D systems. The 3.0 kOhm to 7.0 kOhm input-resistance range identifies the device as a bipolar line receiver rather than a low-voltage CMOS transceiver. The 14-pin SOIC is a surface-mount package suitable for conventional PCB assembly and automated production. Its 0.154 inch pitch matches the widely used narrow-body SOIC footprint family, while the 3.90 mm body width supports compact placement compared with older through-hole receiver packages. Each receiver channel requires the correct external connection and signal conditioning defined by the system interface. Typical uses include RS-232 links between industrial equipment and computers, legacy peripheral ports, point-of-sale equipment, data acquisition systems, and embedded-control consoles. The quad organization is especially useful where four RS-232 inputs must be accepted without installing four separate receiver packages. Designers should still verify channel direction, grounding, signal polarity, and timing against the circuit being interfaced. A key design consideration is that MC1489DG is a receive-only interface. It does not provide the transmit functions required for a complete bidirectional RS-232 port. A separate line driver or transceiver is needed for outbound data. Board design must also preserve adequate spacing and signal return paths so large RS-232 voltage transitions do not create unwanted coupling into nearby low-level circuits. This product page combines manufacturer interface information, package details, application guidance, and focused replacement comparisons for engineers evaluating the MC1489DG in legacy and industrial RS-232 equipment.

RFC Hubungi kami
MC1489M - Quad EIA-232D Receiver | onsemi | SOIC-14
MC1489M

MC1489M - Quad EIA-232D Receiver | onsemi | SOIC-14

The onsemi MC1489M is a monolithic quad EIA-232D line receiver with four independent receive channels, a 3.0 kΩ to 7.0 kΩ input resistance, and an input signal range of ±30 V. The device is supplied in a 14-pin SOIC (SOEIAJ-14) surface-mount package for compact data-terminal and data-communications equipment designs. Its receive-oriented architecture converts bipolar RS-232 signals into digital logic levels while providing response-control terminals for adjustable receiver behavior. A line receiver is an interface IC used at the receiving end of a serial communications link. The MC1489M belongs to the broader line-receiver hierarchy, which includes EIA-232D receivers, interface transceivers, and multi-channel communications interface ICs. Its four channels allow one package to support four RS-232 data inputs, reducing component count in equipment with several serial ports, control links, or diagnostic interfaces. The principal verified features include four receiver channels, 3.0 kΩ to 7.0 kΩ input resistance, and ±30 V input signal capability. Each receiver includes a response-control terminal to which a resistor, or a resistor and bias-voltage source, can be connected. This control allows the receiving behavior to be adjusted when the interface must accommodate different signaling thresholds or system-level conditions. The MC1489M uses Schottky-related input structures to support low-power operation while receiving high-voltage bipolar signals. This is useful in EIA-232D equipment because the transmitter side supplies positive and negative voltages relative to the logic ground. The receiver therefore must tolerate a substantially wider input range than the logic devices connected to its outputs. The four-channel arrangement also preserves separate receive paths for simultaneous or independently controlled links. Typical uses include RS-232 data-terminal equipment, industrial serial interfaces, instrumentation links, peripheral ports, and embedded systems that receive bipolar serial data. In such equipment, the MC1489M can sit between an external RS-232 connector and TTL or CMOS logic. The logic source impedance, grounding arrangement, and response-control network must be selected so the complete interface meets the intended EIA-232D system requirements. Designers should pay particular attention to supply grounding, receiver input protection, unused control pins, and signal routing. A solid signal-ground reference, controlled traces, and appropriate input resistors are essential because RS-232 connectors can be exposed to ESD and other transients. Pin functions and electrical limits must be confirmed against the manufacturer datasheet before layout release or substitution. This product record combines the verified onsemi datasheet information, distributor availability references, cross-reference candidates, and engineering-oriented selection guidance. It distinguishes confirmed drop-in candidates from general functional equivalents and highlights where additional electrical or lifecycle verification is still required.

RFC Hubungi kami
MC1489MG - Quad EIA-232D Receiver | onsemi | 14-SOIC
MC1489MG

MC1489MG - Quad EIA-232D Receiver | onsemi | 14-SOIC

The onsemi MC1489MG is a monolithic quadruple EIA-232D line receiver designed for data-terminal equipment and data-communication equipment interfaces. It contains four receiver channels in a 14-pin SOIC package, accepts input signals ranging from ±30 V, and presents an input resistance between 3.0 kΩ and 7.0 kΩ. The MC1489MG is identified as a commercial extended-temperature grade device. An EIA-232 line receiver is an interface IC that converts bipolar RS-232 voltage levels into digital logic levels. It belongs to the line-receiver class within interface ICs, a larger functional group that also includes RS-232 drivers, transceivers, and multi-protocol interface devices. Unlike a transceiver, the MC1489MG performs reception only, allowing equipment with separate transmit and receive signal paths to use a dedicated receiver for each direction. The four-channel architecture reduces the component count in equipment that exchanges multiple serial signals. Each receiver has a response-control function, which permits a resistor or a resistor and bias-voltage source to influence receiver behavior. Input resistance of 3.0 kΩ to 7.0 kΩ provides the required input loading for EIA-232D interfaces, while the ±30 V input signal range supports the voltage excursions characteristic of RS-232 signaling. The MC1489MG is based on a monolithic low-power Schottky receiver design. This implementation supports four independent receive channels without requiring a separate receiver package for every signal. Because the part contains receivers rather than transmitters, it cannot independently generate the RS-232 voltage swings required to drive a remote communication port; it must be paired with an appropriate line driver when a design needs both transmission and reception. Typical uses include industrial serial interfaces, data-terminal equipment, data-communication equipment, remote-control links, and legacy RS-232 ports. The device is particularly relevant when an existing design requires four receive channels in a single 14-pin surface-mount package. Its commercial extended temperature designation also makes it a candidate for equipment operating outside the usual consumer temperature range. PCB design should preserve the EIA-232 input network, provide a stable supply and ground reference, and route each receiver input away from fast switching or high-current paths. The response-control terminals should be left at the configuration shown in the manufacturer application guidance. Review the pin-description table and operating limits in the manufacturer datasheet before finalizing the footprint and external networks.

RFC Hubungi kami