Produk (44,000+)

MC34072DG - Dual 44V Op Amp | onsemi | Industrial Amplification
MC34072DG

MC34072DG - Dual 44V Op Amp | onsemi | Industrial Amplification

onsemi MC34072DG is a dual general-purpose operational amplifier optimized for single-supply operation from 3.0 V to 44 V. It provides two amplifiers in an 8-pin SOIC package, with 4.5 MHz gain-bandwidth product, 13 V/µs slew rate, and 5 mV typical input offset voltage. The part combines bipolar fabrication with a design that avoids JFET input transistors. An operational amplifier, or op amp, is a voltage-feedback analog IC that amplifies the difference between its inverting and non-inverting inputs. The op amp belongs to the broader hierarchy of amplifier IC, analog IC, semiconductor, and signal-conditioning component. Its gain, input offset, slew rate, common-mode range, output swing, and noise determine how accurately it can process low-level signals in instrumentation, control, sensing, and signal-conditioning circuits. The MC34072 family is particularly useful when a circuit must operate from a single positive supply while accepting signals near ground. Its 3.0 V to 44 V supply range provides flexibility for industrial control systems, test equipment, sensor interfaces, and power-supply feedback networks. The 4.5 MHz gain-bandwidth product supports higher-frequency closed-loop operation than a basic precision amplifier, while the 13 V/µs slew rate improves large-signal response. Two independent amplifiers are integrated in one 8-pin SOIC, reducing component count and board area. MC34072DG is a commercial-temperature, standard general-purpose amplifier. The dual configuration provides separate input and output pins for channels A and B. Typical applications include buffer stages, active filters, transducers, current sensing, sample-and-hold circuitry, comparators, and general-purpose signal conditioning. The dual channel can also support independent signal paths, cascaded stages, or two channels of a differential or multichannel measurement system. Single-supply operation requires careful attention to the input common-mode range and output swing. Inputs must remain inside the amplifier's valid common-mode region, and the output must be biased appropriately when processing signals centered near 0 V. Decoupling capacitors should be placed close to the supply pins, while feedback components should be kept compact to minimize parasitic coupling and preserve the intended bandwidth and stability behavior. This page combines the manufacturer product information, exact MC34072DG orderable-part listings, package information, replacement references, application guidance, and engineering design notes. It also distinguishes package-compatible ordering variants from the dual MC33072DG option so that form, fit, function, and qualification requirements can be checked before PCB substitution.

RFC Hubungi kami
MC34072PG - Dual 44V Op Amp with 13V/us | onsemi
MC34072PG

MC34072PG - Dual 44V Op Amp with 13V/us | onsemi

onsemi MC34072PG is a dual general-purpose operational amplifier with a 3 V to 44 V supply range, 4.5 MHz gain-bandwidth product, and 13 V/us slew rate in an 8-pin PDIP package. The device provides two amplifiers with single-ended outputs and uses quality bipolar fabrication without JFET input technology. An operational amplifier is an amplifier IC that uses high-gain differential feedback to control an output voltage. The MC34072 family belongs to the broader operational amplifier, analog IC, and semiconductor hierarchies. It can operate from split supplies or a single supply and is particularly suited to circuits requiring higher supply tolerance than typical low-voltage rail-to-rail amplifiers. The 4.5 MHz gain-bandwidth product supports useful closed-loop bandwidth at practical gain settings, while the 13 V/us slew rate allows outputs to change quickly without requiring JFET inputs. The manufacturer lists a 5 mV input offset-voltage figure for the commercial-temperature MC34072PG, and its bipolar construction is suited to general-purpose analog signal conditioning. The MC34072 series combines precision bipolar performance with relatively high operating-voltage capability and fast settling behavior. Each amplifier can serve as an inverting or non-inverting stage, and the two independent channels allow simultaneous processing of related signals. This architecture is useful when a board needs one amplifier for filtering and another for buffering or gain control. Typical uses include industrial sensor interfaces, low-frequency active filters, audio preamplifier stages, transducer amplifiers, feedback-control loops, and general instrumentation powered from industrial supply rails. The 44 V maximum supply also makes the device relevant to legacy 24 V control systems, provided the selected operating voltage and dissipation remain within the device ratings. Place bypass capacitors close to the supply pins and route feedback components away from input and output traces to reduce oscillation risk. Confirm output swing, input common-mode range, load current, and thermal dissipation for each amplifier channel. Dual packages require evaluation of channel-to-channel behavior, not only the aggregate device rating. This product page combines the MC34072PG operating characteristics with engineering-focused pin, packaging, replacement, and design guidance. It supports faster selection by placing verified headline specifications beside the practical constraints that determine whether the dual amplifier can operate safely in a target circuit.

RFC Hubungi kami
MC34118DW - Voice-Switched Speakerphone IC | NXP | 28-SOIC
MC34118DW

MC34118DW - Voice-Switched Speakerphone IC | NXP | 28-SOIC

The NXP Semiconductors MC34118DW is a telecom integrated circuit designed for voice-switched speakerphone systems and packaged in a 28-lead SOIC. It integrates the functions required for stand-alone telephone-line speakerphone operation, including direct interfacing to Tip and Ring through a coupling transformer. The device can also work with a handset speech network and additional featurephone functions. Operation from an external power supply or directly from the telephone line provides design flexibility for dedicated and featurephone equipment. A voice-switched speakerphone IC is a telephone-network interface device that detects speech activity and controls the direction of audio between the microphone and loudspeaker paths. It eliminates the need for a manually operated push-to-talk control when both parties remain within microphone pickup range. This category of telephone interface IC sits within communication ICs and ultimately within the broader integrated-circuit hierarchy, combining analog signal conditioning, gain control, and telephone-line switching in one package. The MC34118DW supports telephone-line-powered operation, typically requiring 5.0 mA from the line, as well as operation from a conventional power supply. Its gain in the transmit and receive paths is adjusted externally at the microphone and speaker amplifiers. Component values in the manufacturer datasheet should therefore be treated as starting points, with final gain, stability, and distortion set through prototype measurement in the completed speech network. The 28-lead SOIC package supports direct Tip and Ring interfacing through a coupling transformer, enabling a compact stand-alone speakerphone implementation. Its architecture is suited to analog telephone terminals, extension speakerphone designs, and featurephones that add a hands-free monitoring function to an existing handset speech network. It can also support two-way monitoring functions where the microphone and loudspeaker paths are controlled automatically according to voice activity. Important application choices include telephone-line-powered products, externally powered analog phones, and featurephones requiring a dedicated voice-switched monitoring path. The interface is not a general-purpose audio amplifier or DTMF decoder; it is specifically a telephone speech-network controller. Peripheral filtering, the coupling transformer, microphone and speaker amplifiers, and external gain-setting components remain essential parts of a complete implementation. When laying out a design, place the MC34118DW close to the telephone-network and speech-signal components and keep sensitive microphone inputs away from the loudspeaker drive path. Validate gain, sidetone balance, line-power budget, and stability on the final board because transformer selection and component tolerances strongly influence acoustic performance. Use the pin-description and application-circuit tables in the manufacturer datasheet when assigning PCB tracks. This page consolidates the verified package and operating details, cross-reference alternatives, and practical design guidance for engineers evaluating the MC34118DW in analog telephony equipment.

RFC Hubungi kami
MC34119D - Low-Power Class AB Audio Amplifier | NXP
MC34119D

MC34119D - Low-Power Class AB Audio Amplifier | NXP

The NXP MC34119D is a low-power, mono Class AB audio amplifier integrated circuit designed primarily for telephone equipment, including speakerphones. It operates from a 2 V minimum supply, supports a nominal range of 2 V to 16 V or ±1 V to ±8 V, and provides differential speaker outputs to increase usable output swing at low supply voltages. The device is supplied in an 8-pin SOIC package according to the distributor product listing. An audio amplifier is an integrated circuit that accepts a low-level analog audio signal and delivers enough current and voltage to drive a speaker or another acoustic transducer. The MC34119 belongs to the Class AB amplifier category, where the output transistors conduct during the signal cycle for improved efficiency than a continuously biased Class A design. Its telephone-oriented architecture supports portable and line-powered equipment where low supply voltage and compact implementation are important. The verified feature set includes a shutdown function, a single mono output channel, and differential speaker outputs. Differential outputs are particularly useful in telephone and speakerphone designs because they increase output swing into a differentially connected transducer. The manufacturer datasheet also identifies a 2.0 V minimum supply, allowing operation from low-energy source rails. The Class AB output stage is intended to balance output capability against power consumption in compact audio systems. MC34119D applications include telephone speakerphones, compact voice terminals, intercom equipment, and other low-voltage audio products. In these systems, the amplifier converts a microphone or line-level signal into a differential drive capable of energizing a small speaker. Designers should account for the external output-coupling capacitors shown in the manufacturer application circuit when connecting a speaker, and should verify the shutdown-control polarity and timing before sequencing the device. The most important design consideration is ensuring that the supply, input signal, output network, and speaker load remain within the limits defined by the manufacturer datasheet. Because the target is a legacy low-power audio amplifier, purchasing decisions should also account for lifecycle status, stock, and long-term sourcing rather than assuming availability from an active-production family. This page consolidates the verified package, supply-voltage, amplifier-class, shutdown, and differential-output information with practical selection guidance. It also distinguishes confirmed facts from parameters that require confirmation in the original MC34119 manufacturer datasheet, helping engineers evaluate MC34119D without relying on incomplete distributor summaries.

RFC Hubungi kami
MC34119P - 2-16V Mono Class AB Audio Amp | NXP
MC34119P

MC34119P - 2-16V Mono Class AB Audio Amp | NXP

NXP MC34119P is a low-power, 1-channel Class AB audio amplifier IC designed for telephone equipment, including speakerphones, with a 2 V to 16 V supply range and differential speaker outputs in an 8-pin DIP package. It provides a practical solution where low supply voltage, low quiescent current, and efficient single-speaker drive are required. The available ordering information identifies the device as an NXP USA Inc. 8-PDIP mono audio amplifier. An audio amplifier IC is a semiconductor that accepts a small audio signal and delivers enough voltage and current to drive a loudspeaker or other audio transducer. A Class AB amplifier combines the low crossover distortion of class-A operation with improved efficiency compared with a continuously biased class-A stage. In the MC34119P, differential speaker outputs are intended to maximize output swing at low supply voltages, making the device especially relevant to compact telephone and communications equipment. The MC34119P operates from 2.0 V to 16 V, as documented in the retrieved manufacturer and distributor information. Its typical quiescent supply current is 2.7 mA for battery-powered designs, while shutdown reduces the typical quiescent current to 65 µA. A chip-disable input provides a direct means of placing the amplifier in its low-power state. These features allow the amplifier to remain useful when system power is constrained by a telephone line or battery source. Its architecture uses one Class AB output channel and differential speaker outputs rather than a conventional single-ended output arrangement. Differential drive can provide greater useful voltage swing into the speaker for a given supply, which is important at the 2 V minimum supply. This is a system-level advantage in speakerphone products where loudness and battery efficiency must coexist. Exact continuous output power, output impedance, gain settings, and distortion limits were not included in the retrieved source snippets and must be confirmed in the full manufacturer datasheet before final design sign-off. Typical uses include telephone speakerphones, telephone-line powered communications products, small intercom stations, compact voice monitors, and portable low-voltage audio equipment. The device is also suitable where standby consumption matters, because the shutdown function can isolate the amplifier from the active signal path. For these applications, the 2 V minimum operating voltage and differential output capability align particularly well with low-power, single-speaker systems. The primary design consideration is output-device and load compatibility. Engineers should verify speaker impedance, output power at the available supply voltage, thermal conditions, gain configuration, bypass capacitors, and shutdown logic against the complete MC34119 datasheet. Because the supplied text identifies an 8-DIP footprint but does not enumerate individual terminal functions, the pin assignment and exposed circuit details should not be inferred solely from this page. This product page consolidates the verified MC34119P package, voltage, topology, shutdown, and low-power information with practical application guidance, sourcing considerations, and honest drop-in replacement analysis. Its key value is separating confirmed MC34119P characteristics from unverified specifications and avoiding unsupported claims about substitutes that may require different EMI performance or pin behavior.

RFC Hubungi kami
MC34184M - Low-Power Quad JFET Op Amp | onsemi
MC34184M

MC34184M - Low-Power Quad JFET Op Amp | onsemi

The onsemi MC34184M is a low-power, quad, JFET-input operational amplifier characterized by 210 uA of supply current per amplifier, a 4.0 MHz gain-bandwidth product, and a 10 V/us slew rate. Housed in onsemi's legacy MC34184M package, the device combines low input bias current with high input resistance for instrumentation, signal-conditioning, and low-frequency analog systems. A JFET-input operational amplifier is a voltage-amplifier device whose input stage uses junction field-effect transistors. This input architecture provides high input resistance and low input bias current while supporting relatively low supply-current operation. Within the power-management and analog-signal hierarchy, the MC34184M belongs to the operational-amplifier family and functions as a high-impedance buffer or closed-loop gain stage between sensors, transducers, analog switches, and downstream conversion or control circuitry. The primary performance characteristics of the MC34184M include a 4.0 MHz gain-bandwidth product, 10 V/us slew rate, and approximately 210 uA of supply current per amplifier. Its JFET input stage provides high input resistance, low input offset voltage, and high open-loop gain according to the Motorola MC34184 datasheet. These characteristics make the amplifier appropriate for precision current-voltage conversion, low-level signal amplification, active filtering, and feedback networks operating at low or moderate frequencies. The family architecture also supports practical instrumentation requirements because low input bias current reduces disturbance of high-impedance sources. A high gain-bandwidth product allows useful closed-loop bandwidth above the audio range when configured with conventional compensation and suitable external resistors. The 10 V/us slew rate improves handling of moderately fast signal edges, although the 4.0 MHz bandwidth places the device in the general-purpose precision-amplifier class rather than the high-speed operational-amplifier class. Typical applications include bridge-sensor signal conditioning, biomedical instrumentation, photodiode and phototransistor amplifiers, audio preamplification, active filters, sample-and-hold stages, and low-frequency closed-loop control loops. In each case, the amplifier should be evaluated for input common-mode range, output swing, noise, offset, stability, and supply compatibility under the actual operating conditions. Designers should verify the package dimensions, pin numbering, electrical limits, and common-mode range against the manufacturer documentation before layout. Input and feedback resistors must also be selected for low thermal noise and acceptable bias-current error. Bias compensation may be useful when source resistance is high enough that input bias current produces a material offset across the source impedance. This page organizes the core MC34184M electrical characteristics, practical application guidance, comparison parameters, and design considerations into one engineering-focused reference. It supports early architecture selection while preserving the need to verify production details, lifecycle commitments, and assembly-specific information with the manufacturer before releasing a design.

RFC Hubungi kami
MC3437L - Hex Bus Receiver with Input Hysteresis | Motorola
MC3437L

MC3437L - Hex Bus Receiver with Input Hysteresis | Motorola

The Motorola MC3437L is a six-channel hexadecimal bus receiver with input hysteresis, supplied in a 16-pin CDIP package. The verified distributor listings identify the device as a 0/6 receiver and indicate a listed unit price of $2.6678 at LCSC as of 2026-10-23. The receiver is intended for digital bus-interface applications where noise immunity and signal conditioning are important. A bus receiver is an interface IC that converts a digital logic signal into a cleaner, standardized receiver output. The MC3437L belongs to the receiver and transceiver category, providing six receiver channels rather than a general-purpose analog function. Input hysteresis creates a defined transition region between low and high input levels, helping prevent output chatter when a noisy or slowly changing signal crosses the logic threshold. The verified search data specifically identifies the MC3437 as a Hex Bus Receiver with Input Hysteresis. The MC3437L ordering variant is shown by DigiKey as a 0/6 Receiver in a 16-CDIP package. The available source data does not provide detailed input thresholds, propagation delays, supply-voltage limits, output levels, temperature ratings, or absolute maximum ratings, so those values are not inferred here. Typical uses include digital control buses, computer peripheral interfaces, industrial equipment, communications equipment, and legacy systems where a six-channel receiver is useful. The CDIP package supports through-hole PCB assembly and may be preferred for repair, prototyping, and systems that use conventional DIP-compatible footprints. Actual signal integrity and system compatibility require checking the original manufacturer datasheet and the host bus voltage and timing. When replacing MC3437L, verify the exact pinout, logic polarity, supply requirements, propagation delay, and input thresholds before substitution. Do not assume that a similarly named transceiver or receiver is pin-compatible. The available source data does not establish lifecycle status, detailed electrical ratings, or a verified five-part drop-in replacement set.

RFC Hubungi kami
MC3459P - Quad NMOS Address Line Driver | Motorola
MC3459P

MC3459P - Quad NMOS Address Line Driver | Motorola

The Motorola MC3459P is a quad NMOS address line driver, also described as a bipolar bus driver, packaged in a 14-pin DIP. The device contains four address-driver elements, each with a one-bit output, for driving address and control lines in older digital systems. According to the available distributor and datasheet listings, the MC3459P operates from a 5.25 V supply and is categorized as an address driver, bus driver, buffer, driver, receiver, and transceiver. A bus driver is an interface IC that strengthens digital signals so they can reliably travel between circuit boards, processors, memories, and peripheral devices. Within the logic-IC hierarchy, a bus driver sits below interface ICs and above general-purpose buffers. The MC3459P is specifically intended to drive multiple address lines in systems where the source device cannot directly provide the required output current or signal integrity. The main verified characteristics are a four-element architecture, one-bit output per element, a 5.25 V supply designation, bipolar bus-driver construction, and a 14-pin DIP package. The listings also identify the device as a Quad NMOS Address Line Driver. The exact output-current rating, propagation delay, output disable levels, input and output logic levels, operating temperature range, and absolute maximum ratings are not present in the supplied search data and therefore require confirmation from the manufacturer datasheet before release to production. The 14-pin through-hole package makes the MC3459P suitable for legacy computer, industrial-control, instrumentation, and data-acquisition equipment where motherboard-level bus routing and socketed DIP construction remain practical. Its four independent driver elements can be assigned to address or control lines when the system architecture requires buffered digital outputs. Modern designs may instead favor surface-mount bus-driver ICs with documented electrical limits and lifecycle guarantees. Engineers should confirm the pinout, enable-control polarity, and logic thresholds before substitution because the supplied distributor records identify the function and package but do not provide a complete pin table. Power-supply decoupling, unused-input handling, and signal-integrity checks should follow the manufacturer datasheet rather than assumptions based on generic 14-pin bus drivers. This page combines verified distributor descriptions, package information, sourcing records, and qualification data into a structured engineering reference. It also documents the remaining datasheet-dependent parameters and the limited cross-reference evidence so that engineers can distinguish confirmed facts from data requiring validation before procurement or PCB redesign.

RFC Hubungi kami
MC3461L - Dual Current Sense Amplifier | Motorola | CDIP-16
MC3461L

MC3461L - Dual Current Sense Amplifier | Motorola | CDIP-16

The Motorola MC3461L is a dual current-sense amplifier in a 16-pin CDIP package, with two amplifier circuits for measuring current across low-value shunt resistors. The verified distributor data identifies the device as a high-speed NMOS/MECL current-sense amplifier, while detailed electrical limits, gain values, common-mode range, supply voltage, and temperature ratings are not included in the supplied records and therefore remain unconfirmed. Its instrumentation-amplifier classification places it among amplifier ICs used for power-conversion monitoring, motor control, battery management, and power-supply feedback. A current-sense amplifier is a specialized voltage-feedback amplifier that develops a measurable output voltage from the small differential voltage created by current flowing through a shunt resistor. The MC3461L contains two circuits, allowing one packaged device to monitor two independent current paths when the circuit board has sufficient isolation and the operating conditions of both channels are compatible. The 16-CDIP mechanical format is a through-hole ceramic dual in-line package intended for legacy industrial, instrumentation, and telecommunications equipment. The MC3461L's two-circuit architecture reduces component count compared with two separate single amplifiers, while its small shunt-generated differential signal supports compact sensing layouts. However, stable measurement depends on selecting an appropriate shunt, keeping Kelvin connections narrow and symmetrical, and observing the amplifier's common-mode and output limits. Because those numerical limits are absent from the verified excerpts, designers should consult the complete manufacturer datasheet before finalizing resistor values, gain configuration, supply rails, or production tolerances. The MC3461L is suitable for power-supply current monitoring, battery charge and discharge sensing, motor-control feedback, industrial process-control systems, and communications equipment. In these applications, the amplifier converts bidirectional or unidirectional shunt current into a voltage suitable for an ADC, controller, comparator, or protection circuit. The exact input polarity, output reference arrangement, and permissible common-mode voltage must be verified from the full datasheet before layout sign-off. A practical design begins by placing the shunt and amplifier in the same high-current path, routing the sense traces as a tightly coupled differential pair, and grounding the unused inputs or amplifier according to the manufacturer's recommended configuration. Decoupling capacitors should connect directly to the supply pins, and the output must remain within the device's verified output range. PCB creepage, clearance, copper heating, and Kelvin-trace geometry are as important as the IC choice in a high-current design. This page combines verified distributor identity and availability information with clearly marked engineering gaps, practical application context, and design guidance. It does not infer missing electrical specifications from the MC3461 family name, so procurement, electrical, and package decisions should be completed against the official datasheet and current authorized-channel inventory.

RFC Hubungi kami
MC3476P1 Low-Cost Programmable Operational Amplifier | onsemi
MC3476P1

MC3476P1 Low-Cost Programmable Operational Amplifier | onsemi

The onsemi MC3476P1 is a low-cost, programmable operational amplifier designed for general-purpose analog signal conditioning. The device is associated with an 8-pin DIP package, and its core features include low power consumption, high input impedance, and a programmable operating point that allows engineers to adapt the amplifier to different bias and performance requirements. The MC3476P1 is therefore useful in applications requiring adjustable amplifier behavior rather than a fixed, conventional op-amp configuration. An operational amplifier is a voltage-controlled differential amplifier with very high open-loop gain. Its two inputs are the inverting input and non-inverting input, while the output is controlled by feedback in most practical circuits. The programmable family represented by the MC3476P1 adds a bias-current control function, allowing the operating current and associated performance to be adjusted externally. This makes the device more flexible than a fixed-bias amplifier when system designers need to balance power consumption, bandwidth, output drive, and signal-source loading. The MC3476P1 is described by its manufacturer as a low-cost selection of the MC1776 programmable operational-amplifier family. Its low power consumption is useful in battery-powered, portable, and low-power instrumentation systems. High input impedance helps reduce loading on high-impedance signal sources, which can help preserve signal amplitude and reduce input-stage interaction. The programmable bias architecture also gives designers a way to tailor performance after considering source impedance, gain, bandwidth, and acceptable supply current. Typical analog uses include sensor-interface stages, low-frequency instrumentation, buffer and gain stages, active filters, and signal-conditioning blocks in industrial or embedded control systems. The device can be used where a general-purpose amplifier is sufficient and adjustable operating current is valuable. Designers should review the manufacturer datasheet for guaranteed input-voltage range, output-swing limits, supply-current ranges, gain-bandwidth behavior, offset voltage, input bias current, and package details before finalizing a design. A key implementation consideration is the connection of the programmable-bias circuitry. Incorrect resistor values, unsuitable bypassing, or operation outside the specified supply and common-mode ranges can reduce stability or prevent expected output behavior. Keep the input network and feedback components close to the device, use a stable bypass capacitor at the supply pins, and verify noise, settling time, and output-swing requirements with the actual source impedance and load. This page combines the manufacturer-linked product identity, documented package information, application guidance, and practical design considerations for engineers evaluating the MC3476P1. Because the exact electrical limits and pin assignments are not reproduced in the cited search results, consult the original MC3476P1 datasheet for authoritative values before schematic release, PCB layout, or production qualification.

RFC Hubungi kami
MC3486D - 4-Channel RS-422/423 Receiver | Texas Instruments
MC3486D

MC3486D - 4-Channel RS-422/423 Receiver | Texas Instruments

The Texas Instruments MC3486D is a monolithic quadruple differential line receiver with four independent differential inputs, TTL-compatible 3-state outputs, and single 5 V operation in a 16-pin SOIC package. It is designed for ANSI TIA/EIA-422-B and TIA/EIA-423-B and ITU V.10 and V.11 interfaces. The four receivers convert balanced differential line signals into digital logic levels, making the device suitable for multi-channel industrial, communications, and data-acquisition systems. A differential line receiver is an interface IC that rejects common-mode noise and extracts a logic decision from two complementary conductors. The receiver belongs to the line-interface hierarchy: differential receiver → RS-422/RS-423 interface IC → digital interface IC → semiconductor. This category is used where transmitted logic signals must cross cables or noisy interconnects without allowing voltage offsets and interference to corrupt the receiving logic. The MC3486 provides four independent channels, a shared enable control for the output states, and TTL-compatible outputs. Its 3-state capability permits each receiver output to enter a high-impedance state when the interface is not being selected. Fast transition times support reliable signaling, while the single 5 V supply simplifies connection to conventional TTL and CMOS-compatible system logic. The MC3486D is particularly suited to balanced communication links using RS-422 or RS-423 signaling. It can terminate long or electrically noisy interconnects at the receiving end, while its differential input structure provides noise immunity compared with a single-ended receiver. The device is also intended for use with the MC3487 quadruple differential line driver, creating matched transmit and receive channels. Typical applications include industrial control links, instrumentation interfaces, multidrop communication systems, test equipment, and embedded systems requiring several differential inputs. Designers should provide the termination and biasing values required by the selected line standard, respect the enable polarity and output timing, and validate cable length and topology against the system’s signal-integrity requirements. This page summarizes verified manufacturer information and distributor presence, while clearly separating unavailable electrical details. The MC3486D’s main engineering value is its combination of four differential channels, 3-state TTL outputs, standards-oriented RS-422/RS-423 positioning, and a compact 16-pin surface-mount package.

RFC Hubungi kami
MC3486DE4 - Quad RS-422/RS-423 Differential Line Receiver | Texas Instruments
MC3486DE4

MC3486DE4 - Quad RS-422/RS-423 Differential Line Receiver | Texas Instruments

The Texas Instruments MC3486DE4 is a monolithic quadruple differential line receiver with 3-state TTL-compatible outputs, designed to meet ANSI TIA/EIA-422-B and TIA/EIA-423-B and ITU V.10/V.11 specifications, and supplied in a 16-pin SOIC (0.154 inch, 3.90 mm wide) package. A differential line receiver is a type of interface transceiver IC that recovers a logic signal from a balanced, differential transmission line such as RS-422 or RS-423. Its category hierarchy runs differential line receiver -> line receiver -> interface transceiver IC -> integrated circuit. Receivers are used where a sender is physically separated from the receiver by cable, where the signal has travelled through noisy industrial environments, or where several devices share one bus. Differential signalling rejects common-mode noise, and the 3-state output stage lets a controller share a single data bus between multiple receivers without bus contention. The MC3486 offers four independent differential-input receivers in one package, with fast transition times and TTL-compatible outputs that drive standard CMOS/TTL logic directly. Because the outputs can be placed in a high-impedance state, the four channels can be muxed onto a shared data bus for multiplexing, bus arbitration, or test isolation. All four channels share common supply pins, so the device fits naturally into parallel, wide-bus architectures such as multi-drop data acquisition and instrumentation systems. Internally, each channel consists of a differential input stage, a Schmitt-trigger style response that rejects slow-moving noise on the differential pair, and an output buffer with three drive states (high, low, high impedance). The differential threshold and common-mode range are set to suit balanced twisted-pair cabling rather than single-ended logic, which is why the device is specified against EIA/TIA-422-B and EIA/TIA-423-B instead of general-purpose logic levels. Typical uses include industrial serial data acquisition, instrumentation and test equipment interfaces, computer-to-peripheral links, and control systems that must recover a differential signal over long cable runs. It is also commonly paired with a complementary quadruple differential line driver such as the MC3487 family, or with the MC1489/MC1488 families, to build complete balanced communication links. When designing around the MC3486DE4, budget the enable pins and supply rails carefully: leaving an output enabled while another receiver drives the same bus node causes contention and excess current. Confirm the receiver's common-mode input range against the ground reference of the remote device, and place a termination network at the far end of the cable so the differential pair is referenced properly.

RFC Hubungi kami
MC3486DG4 - Quad RS-422/423 Receiver | Texas Instruments
MC3486DG4

MC3486DG4 - Quad RS-422/423 Receiver | Texas Instruments

Texas Instruments MC3486DG4 is a monolithic quadruple differential line receiver with four independent receiver channels, a 4.75 V to 5.25 V supply range, and a 16-pin SOIC package. It supports RS-422 and RS-423 signaling and is designed to meet ANSI TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10, and ITU V.11 requirements. A differential line receiver is an interface IC that converts a balanced differential signal arriving over a cable into a logic-level output for a digital system. The MC3486 belongs to the receiver category within the broader line-driver and transceiver hierarchy. Its four independent channels allow one device to terminate and decode four differential inputs, reducing component count in multi-channel data acquisition, industrial control, and communications equipment. The principal features include four receiver channels, three-state outputs, TTL-compatible signaling, and operation from a nominal 5 V supply. The listed maximum receive delay is 35 ns, making the device suitable for systems that require rapid recovery of differential data from balanced lines. Its commercial temperature grade extends from 0 °C to 70 °C, while the 16-SOIC package supports conventional surface-mount PCB assembly. Each receiver channel uses differential input signaling to reject common-mode voltage present on cabling and grounding environments. Three-state outputs permit the output pins to enter a high-impedance state when the system needs to share a data bus or isolate a receiver. The MC3486 therefore combines standard RS-422 and RS-423 reception with bus-oriented output control rather than functioning as a simple single-ended logic receiver. Typical applications include industrial serial interfaces, test and measurement systems, data acquisition equipment, and legacy computer peripherals that communicate over balanced differential lines. Four channels make the device especially useful where multiple cable-connected sensors, controllers, or peripheral boards must feed a common digital processor. The 5 V operating range also allows the receiver to operate alongside conventional TTL and CMOS interface logic when appropriate voltage compatibility is maintained. Designers should verify receiver enable and output-state timing against the system clock, preserve adequate differential signal margin at the cable interface, and account for connector and cable characteristics. The 35 ns maximum receive delay is a useful timing boundary when calculating setup-and-hold margins or supporting legacy peripheral clocking. Decoupling should follow the connection recommendations in the manufacturer datasheet. This product page combines the device architecture, interface standards, timing information, verified drop-in candidates, package considerations, and practical application guidance. It also distinguishes confirmed replacement options from parts that require additional qualification, helping engineers narrow a design without confusing protocol compatibility with complete production suitability.

RFC Hubungi kami
MC3486DR - 4-Channel RS-422/423 Receiver | Texas Instruments (Tape & Reel)
MC3486DR

MC3486DR - 4-Channel RS-422/423 Receiver | Texas Instruments (Tape & Reel)

The Texas Instruments MC3486DR is a monolithic quadruple differential line receiver with four independent differential inputs, TTL-compatible 3-state outputs, and single 5 V operation in a 16-pin SOIC package. It is designed for ANSI TIA/EIA-422-B and TIA/EIA-423-B and ITU V.10 and V.11 interfaces. The four receivers convert balanced differential line signals into digital logic levels, making the device suitable for multi-channel industrial, communications, and data-acquisition systems. A differential line receiver is an interface IC that rejects common-mode noise and extracts a logic decision from two complementary conductors. The receiver belongs to the line-interface hierarchy: differential receiver → RS-422/RS-423 interface IC → digital interface IC → semiconductor. This category is used where transmitted logic signals must cross cables or noisy interconnects without allowing voltage offsets and interference to corrupt the receiving logic. The MC3486 provides four independent channels, a shared enable control for the output states, and TTL-compatible outputs. Its 3-state capability permits each receiver output to enter a high-impedance state when the interface is not being selected. Fast transition times support reliable signaling, while the single 5 V supply simplifies connection to conventional TTL and CMOS-compatible system logic. The MC3486DR is particularly suited to balanced communication links using RS-422 or RS-423 signaling. It can terminate long or electrically noisy interconnects at the receiving end, while its differential input structure provides noise immunity compared with a single-ended receiver. The device is also intended for use with the MC3487 quadruple differential line driver, creating matched transmit and receive channels. Typical applications include industrial control links, instrumentation interfaces, multidrop communication systems, test equipment, and embedded systems requiring several differential inputs. Designers should provide the termination and biasing values required by the selected line standard, respect the enable polarity and output timing, and validate cable length and topology against the system’s signal-integrity requirements. This page summarizes verified manufacturer information and distributor presence, while clearly separating unavailable electrical details. The MC3486DR’s main engineering value is its combination of four differential channels, 3-state TTL outputs, standards-oriented RS-422/RS-423 positioning, and a compact 16-pin surface-mount package.

RFC Hubungi kami
MC3486DRE4 - 4-Channel RS-422 Receiver | Texas Instruments
MC3486DRE4

MC3486DRE4 - 4-Channel RS-422 Receiver | Texas Instruments

Texas Instruments MC3486DRE4 is a quadruple differential line receiver with 3-state TTL-compatible outputs, designed for RS-422 and RS-423 communications from a single 5 V supply. The device provides four independent receiver channels in a 16-pin SOIC package and supports a maximum receive delay of 35 ns. A differential line receiver is an interface IC that converts small differential signals appearing across a balanced pair of conductors into a single-ended logic signal. The MC3486 belongs to the receiver hierarchy within differential line-interface ICs, alongside transceivers, drivers, and comparators. Its differential input arrangement helps reject common-mode noise encountered on industrial, telecommunications, and data-processing cables. The principal features include four independent receiver channels, 3-state outputs, and compatibility with EIA/TIA-422-B and EIA/TIA-423-B requirements. The device also supports ITU Recommendations V.10 and V.11, operates from one 5 V supply, and uses TTL-compatible output levels for direct connection to common digital logic. Fast transition times support reliable operation in multi-drop and point-to-point communication arrangements. Internally, each receiver continuously compares its differential input with a threshold established by the line-driver and receiver ecosystem. When the output-enable function is active, the corresponding logic output reflects the received state; when disabled, the output enters a high-impedance state. This permits multiple devices to share a bus without creating output contention. The 16-pin SOIC outline provides a conventional surface-mount interface between the line receiver and an assembled circuit board. Typical applications include balanced data links using the MC3487 quadruple differential line driver, industrial control interfaces, telecommunications equipment, peripheral data buses, and test systems requiring TTL-compatible receiver outputs. The component is particularly useful when a design must decode differential signaling while presenting conventional single-ended logic to a microprocessor, FPGA, or peripheral interface. Designers should route each differential pair as a controlled-impedance pair, maintain the intended input/output common-mode limits, and account for enable timing when multiple receivers share a bus. Decoupling capacitors should be placed close to the supply pins, while unused inputs and disabled outputs require the pin-state and termination recommendations specified in the manufacturer datasheet. This product page combines the manufacturer device information, package details, interface standards, direct replacement information, comparison data, and practical interface-design guidance. It also distinguishes exact MPN and packaging options from electrically similar receiver families that may not be pin-compatible replacements.

RFC Hubungi kami
MC3486N - 4-Channel RS-422/423 Receiver | Texas Instruments
MC3486N

MC3486N - 4-Channel RS-422/423 Receiver | Texas Instruments

The Texas Instruments MC3486N is a monolithic quadruple differential line receiver with four independent RS-422/RS-423 channels, TTL-compatible outputs, and 3-state output capability in a 16-pin PDIP package. According to the manufacturer product page, the device is designed for ANSI TIA/EIA-422-B and TIA/EIA-423-B operation, with compatibility for ITU V.10 and V.11. The MC3486 operates from a single 5 V supply and is characterized for operation from 0°C to 70°C. It is supplied in a 16-pin package. A differential line receiver is an interface-circuit type that converts balanced or differential signaling into a single-ended digital signal. It belongs to the broader hierarchy of transceiver interface ICs, communication interfaces, logic-level conversion devices, and semiconductors. In an RS-422 system, the receiver helps recover a reliable logic state from a differential line while rejecting common-mode noise. The MC3486 is intended for systems using the complementary MC3487 quadruple differential line driver. The principal features visible in the verified manufacturer information are four independent differential-input receivers, TTL-compatible outputs, and a high-impedance output state on each channel. The 3-state outputs support shared-bus arrangements when multiple receivers or bus drivers need to be isolated. The single 5 V supply simplifies interface design, while the 0°C to 70°C characterization targets commercial-temperature equipment. The MC3486 is suitable for industrial control links, multi-channel data acquisition, instrumentation, computer peripherals, and embedded communication interfaces where balanced differential signaling is preferred over single-ended interconnects. Its four channels allow several receiver functions to share one IC, reducing board area and simplifying firmware or system configuration. The device is intended to be used with suitable line drivers and properly terminated transmission lines. The main design consideration is ensuring that the selected companion driver, cable, termination, grounding, and logic interface match the system requirements. The manufacturer states that the MC3486 is designed for optimum performance with the MC3487 quadruple differential line driver. Review the official datasheet for electrical limits, enable or output-control details, and application-specific timing before finalizing a circuit. This page combines the verified manufacturer specifications, distributor package information, source URLs, and practical interface-selection guidance. It is intended to help engineers identify the correct device, compare compatible alternatives, and plan a robust differential-interface implementation.

RFC Hubungi kami
MC3486NE4 - Quad Differential Line Receiver | Texas Instruments
MC3486NE4

MC3486NE4 - Quad Differential Line Receiver | Texas Instruments

Texas Instruments MC3486NE4 is a monolithic quadruple differential line receiver with four independent differential inputs, TTL-compatible outputs, and 3-state output capability in a 16-pin through-hole DIP package. Designed for balanced digital-interface systems, it supports ANSI TIA/EIA-422-B and TIA/EIA-423-B environments as well as ITU V.10 and V.11 recommendations. The four receiver channels provide a practical way to recover logic-level signals from differential data lines while supporting connection to shared buses through high-impedance output states. A differential line receiver converts the voltage difference between two conductors into a conventional logic-level output. This receiver belongs to the line-driver and line-receiver hierarchy, within interface ICs and data-communication ICs. Differential signaling improves common-mode-noise rejection and allows data to be transmitted reliably over longer cable runs than a single-ended interface. The MC3486NE4 implements four such channels in one package, reducing component count in multi-channel industrial, communications, and data-processing equipment. The principal features include four independent differential receivers, TTL-compatible outputs, 3-state operation for bus-oriented connection, and compatibility with ANSI TIA/EIA-422-B, ANSI TIA/EIA-423-B, ITU V.10, and ITU V.11 interface standards. Its through-hole 16-pin DIP construction supports conventional PCB assembly and repair. The MC3486NE4 suffix identifies the commercial-temperature, plastic-DIP ordering configuration, although individual electrical limits should be confirmed against the manufacturer datasheet for the operating conditions of the finished design. In a typical interface, a remote transmitter sends balanced data into a twisted pair, and the MC3486NE4 detects the differential voltage to produce a logic output for a UART, microprocessor, programmable logic, or other digital controller. Because each receiver is independent, four unrelated channels can be decoded in parallel. The 3-state output feature also permits a receiver output to be disconnected when multiple devices share a bus, provided the control and pull-up arrangements follow the system design requirements. Typical applications include industrial control links, instrumentation interfaces, peripheral data links, telecommunications equipment, and legacy computer peripherals. The device is especially relevant where a modern controller must connect to an RS-422 or RS-423 interface while minimizing the number of receiver packages. Its four-channel architecture can also simplify multi-axis positioning, test systems, and distributed control networks that carry several low-speed differential signals. Designers should verify input voltage limits, common-mode range, propagation delay, enable timing, output drive capability, and temperature limits against the manufacturer datasheet before finalizing the interface. Decoupling and signal-return paths should be arranged to prevent fast digital edges and cable transients from coupling into adjacent channels. Through-hole construction provides mechanical robustness, but the PCB must preserve the exact pin orientation and provide adequate clearance for the receiver's through-hole leads. This page organizes the manufacturer interface standards, package information, sourcing details, candidate replacements, and practical selection guidance for engineers evaluating the MC3486NE4. Cross-references are presented as design aids and should be checked against the complete pinout, timing characteristics, logic states, and environmental limits before a substitution is approved.

RFC Hubungi kami
MC3486NG4 - Quad Differential Line Receiver | Texas Instruments
MC3486NG4

MC3486NG4 - Quad Differential Line Receiver | Texas Instruments

Texas Instruments MC3486NG4 is a monolithic quadruple differential line receiver with four independent receivers, TTL-compatible outputs, and three-state output capability in a 16-pin DIP package. Each channel receives differential RS-422 or RS-423 signals, while the tri-state outputs allow multiple devices to share a bus when an output-enable control is inactive. The device operates from a single 5 V supply and is designed for industrial automation and control systems. A differential line receiver is an interface integrated circuit that converts a pair of complementary voltage signals into a single-ended logic-level output. This class of receiver belongs to the interface IC hierarchy, where physical-layer signal conditioning sits between external wiring and digital control logic. Differential reception improves noise immunity by comparing the voltage difference between two conductors rather than relying on one conductor referenced only to ground. The MC3486 provides four complete receiver channels in one package. Its differential inputs support the electrical characteristics associated with TIA/EIA-422-B and TIA/EIA-423-B interfaces, as well as ITU Recommendations V.10 and V.11. TTL-compatible outputs simplify connection to microcontrollers, programmable logic controllers, counters, and other digital systems. Three-state outputs provide a high-impedance condition that can isolate an inactive channel during shared-bus operation. The monolithic implementation gives each receiver an independent signal path while reducing the number of components required on a multi-channel interface card. Operating from one 5 V supply also simplifies system power distribution. The device is particularly suited to RS-422 and RS-423 point-to-point or multidrop arrangements where four balanced channels must be terminated and converted into logic signals. Typical uses include factory automation controllers, industrial data acquisition systems, remote instrumentation, process-control equipment, and communications interfaces. Because the receiver converts external cable signals into digital logic levels, board-level termination, grounding, and routing remain important for dependable operation in electrically noisy environments. Designers should follow the manufacturer datasheet for enable polarity, receiver input handling, supply requirements, and operating limits. Place input and enable traces away from high-current switching paths, use the recommended receiver network, and maintain a low-impedance ground reference between the interface board and its external equipment. This page combines the manufacturer interface description, package information, practical RS-422 and RS-423 design guidance, compatible-product links, and an engineering-focused comparison of identified same-family receiver options.

RFC Hubungi kami
MC3486NS - Quad Differential RS-422/423 Receiver | Texas Instruments
MC3486NS

MC3486NS - Quad Differential RS-422/423 Receiver | Texas Instruments

The Texas Instruments MC3486NS is a monolithic quadruple differential line receiver with four independent differential inputs, TTL-compatible outputs, and 3-state output capability in a 16-pin SOIC package. It operates from a single 5 V supply, is designed around TIA/EIA-422-B and TIA/EIA-423-B signaling, and supports the ITU V.10 and V.11 recommendations. The receiver is intended for industrial-control, data-communication, and instrumentation interfaces where multiple balanced lines must be converted into digital logic levels. A differential line receiver is an interface IC that compares two complementary conductors, rejects common-mode voltage and noise, and converts the resulting logic state into a single-ended digital output. In the signal-processing hierarchy, the MC3486NS belongs to the receiver family within line-driver and receiver interface ICs, which ultimately fall under interface ICs and semiconductors. Its four channels allow one package to replace four discrete differential receiver sections while preserving a standardized balanced-line interface. Key features include four differential receivers, TTL-compatible outputs, selectable 3-state output operation, operation from a single 5 V supply, and compatibility with TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10, and ITU V.11 requirements. The 3-state outputs allow several devices to share a bus when the system controller can place individual receivers in a high-impedance state. The 16-pin surface-mount package supports compact circuit layouts while preserving conventional through-hole-equivalent pin organization. The MC3486 is designed for optimum operation with the MC3487 quadruple differential line driver, providing a complete four-channel transmit-and-receive solution for balanced communications. Its differential input architecture is valuable where cables may pick up noise or where logic devices share a common ground reference. The receiver translates that differential information into TTL-compatible logic suitable for programmable logic controllers, microprocessors, counters, and other digital control systems. Typical uses include industrial automation equipment, RS-422-compatible control links, data acquisition systems, test and measurement instruments, and embedded control equipment requiring several differential inputs. In a four-wire RS-422 interface, the MC3486NS can receive four balanced signals while a corresponding MC3487 family driver transmits the opposite-direction signals. This arrangement supports full-duplex communication over a cable carrying multiple data and control lines. The principal design consideration is correct enable and termination management. The available verified information identifies 3-state outputs but does not provide the detailed enable truth table or pin-level values, so those items must be confirmed in the manufacturer datasheet before implementation. Differential-pair routing, solid grounding, and appropriate cable termination are also essential because receiver performance depends on the physical signal path as well as the IC. This page combines verified manufacturer and distributor information with package guidance, application-oriented analysis, and a drop-in cross-reference assessment. It also distinguishes confirmed substitutes from parts that are only functionally related, helping engineers avoid selecting a driver or a mechanically incompatible package as a receiver replacement.

RFC Hubungi kami
MC3486NSR - Quad Differential RS-422/423 Receiver | Texas Instruments (Tape & Reel)
MC3486NSR

MC3486NSR - Quad Differential RS-422/423 Receiver | Texas Instruments (Tape & Reel)

The Texas Instruments MC3486NSR is a monolithic quadruple differential line receiver with four independent differential inputs, TTL-compatible outputs, and 3-state output capability in a 16-pin SOIC package. It operates from a single 5 V supply, is designed around TIA/EIA-422-B and TIA/EIA-423-B signaling, and supports the ITU V.10 and V.11 recommendations. The receiver is intended for industrial-control, data-communication, and instrumentation interfaces where multiple balanced lines must be converted into digital logic levels. A differential line receiver is an interface IC that compares two complementary conductors, rejects common-mode voltage and noise, and converts the resulting logic state into a single-ended digital output. In the signal-processing hierarchy, the MC3486NSR belongs to the receiver family within line-driver and receiver interface ICs, which ultimately fall under interface ICs and semiconductors. Its four channels allow one package to replace four discrete differential receiver sections while preserving a standardized balanced-line interface. Key features include four differential receivers, TTL-compatible outputs, selectable 3-state output operation, operation from a single 5 V supply, and compatibility with TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10, and ITU V.11 requirements. The 3-state outputs allow several devices to share a bus when the system controller can place individual receivers in a high-impedance state. The 16-pin surface-mount package supports compact circuit layouts while preserving conventional through-hole-equivalent pin organization. The MC3486 is designed for optimum operation with the MC3487 quadruple differential line driver, providing a complete four-channel transmit-and-receive solution for balanced communications. Its differential input architecture is valuable where cables may pick up noise or where logic devices share a common ground reference. The receiver translates that differential information into TTL-compatible logic suitable for programmable logic controllers, microprocessors, counters, and other digital control systems. Typical uses include industrial automation equipment, RS-422-compatible control links, data acquisition systems, test and measurement instruments, and embedded control equipment requiring several differential inputs. In a four-wire RS-422 interface, the MC3486NSR can receive four balanced signals while a corresponding MC3487 family driver transmits the opposite-direction signals. This arrangement supports full-duplex communication over a cable carrying multiple data and control lines. The principal design consideration is correct enable and termination management. The available verified information identifies 3-state outputs but does not provide the detailed enable truth table or pin-level values, so those items must be confirmed in the manufacturer datasheet before implementation. Differential-pair routing, solid grounding, and appropriate cable termination are also essential because receiver performance depends on the physical signal path as well as the IC. This page combines verified manufacturer and distributor information with package guidance, application-oriented analysis, and a drop-in cross-reference assessment. It also distinguishes confirmed substitutes from parts that are only functionally related, helping engineers avoid selecting a driver or a mechanically incompatible package as a receiver replacement.

RFC Hubungi kami
MC3487D - 4-Channel RS-422 Driver | Texas Instruments | 5V
MC3487D

MC3487D - 4-Channel RS-422 Driver | Texas Instruments | 5V

The Texas Instruments MC3487D is a quadruple differential line driver with four independent drivers, a 5 V single supply, and a 16-pin SOIC package. Its differential outputs meet ANSI TIA/EIA-422-B and ITU Recommendation V.11 requirements, while the tri-state outputs permit a high-impedance state for bus management. Each channel uses a TTL-compatible buffered input to reduce loading, making the device suitable for RS-422 point-to-point and multidrop communications. A differential line driver is an interface IC that converts a single-ended logic signal into a balanced pair of differential signals. In the hierarchy of electronic components, it belongs to the interface IC family, within communication and transceiver devices. Differential signaling improves noise immunity by rejecting common-mode noise and allows reliable data transmission over longer cable runs than ordinary single-ended digital logic. The MC3487D provides four driver channels rather than a full transceiver, so it does not receive differential data. The output-enable function controls the output state, allowing connected drivers to be disabled when they are not active. This is useful in systems that share a bus or require controlled output states. Power-up and power-down protection are also identified in the manufacturer documentation. Typical uses include industrial RS-422 links, data acquisition systems, test equipment, instrumentation, and multi-channel communication links. The 5 V supply operation simplifies interface design in legacy and industrial systems where the host logic uses a 5 V rail. Because it is a driver-only device, the system designer must provide the receiving circuitry and define cable termination, grounding, and enable-control behavior. The main design considerations are signal integrity, cable length, supply decoupling, and output-state control. Differential pairs should be routed with consistent geometry and appropriate grounding. The output-enable signals should be controlled during reset so that multiple channels do not contend on a shared bus. The device is intended for surface-mount assembly in the 16-pin SOIC package.

RFC Hubungi kami
MC3487DE4 - Quad RS-422 Line Driver | Texas Instruments
MC3487DE4

MC3487DE4 - Quad RS-422 Line Driver | Texas Instruments

Texas Instruments MC3487DE4 is a quadruple differential line driver with four independent outputs, a single 5 V supply, and a 16-pin SOIC package. Each channel receives a TTL-compatible input and produces a balanced differential signal designed to meet ANSI TIA/EIA-422-B and ITU Recommendation V.11 requirements. The MC3487DE4 is suitable for industrial control, instrumentation, data acquisition, telecom, and test-equipment systems that transmit digital signals reliably over longer cable distances than single-ended logic permits. A differential line driver is an interface IC that converts one logic input into two complementary outputs. This arrangement rejects much of the common-mode noise picked up by a cable, improving signal integrity in industrial environments. The MC3487 belongs to the broader interface-IC hierarchy: line driver → differential line driver → digital interface IC → semiconductor. Its four channels allow one package to drive four separate balanced links while sharing a common supply and ground reference. Key features include four independent differential drivers, TTL-compatible buffered inputs, three-state output capability, fast transition times, and high-impedance inputs. Power-up and power-down protection helps prevent uncontrolled driver activity during supply changes. The buffered inputs reduce input loading, allowing the device to operate reliably with standard TTL and CMOS control logic when voltage-level compatibility is confirmed in the system design. Technically, the MC3487 is a single-supply RS-422-focused transmitter rather than a complete bidirectional transceiver. It does not include receiver channels. Systems requiring two-way communication normally combine this driver with a separate differential receiver, such as a compatible RS-422 receiver IC. The differential outputs should be routed as a matched pair to preserve signal polarity and minimize common-mode conversion along the cable. Typical applications include RS-422 test equipment, industrial automation links, programmable logic controller interfaces, data-acquisition systems, servo or motor-control signaling, point-to-point computer peripherals, and instrumentation. Designers should use twisted-pair wiring, provide a stable 5 V supply, connect the common ground reference, and account for the voltage drop and noise margin of the selected cable length. The principal design consideration is ensuring that every connected receiver recognizes the driver’s differential output levels and that unused outputs are handled according to the manufacturer’s recommendations. PCB placement should minimize the distance between the interface connector and driver outputs, while avoiding noisy switching-current paths near the differential traces. This page combines device specifications, sourcing guidance, drop-in alternatives, and practical interface-design notes for engineers evaluating the MC3487DE4.

RFC Hubungi kami
MC3487DR - 4-Channel RS-422 Driver | Texas Instruments | 5V (Tape & Reel)
MC3487DR

MC3487DR - 4-Channel RS-422 Driver | Texas Instruments | 5V (Tape & Reel)

The Texas Instruments MC3487DR is a quadruple differential line driver with four independent drivers, a 5 V single supply, and a 16-pin SOIC package. Its differential outputs meet ANSI TIA/EIA-422-B and ITU Recommendation V.11 requirements, while the tri-state outputs permit a high-impedance state for bus management. Each channel uses a TTL-compatible buffered input to reduce loading, making the device suitable for RS-422 point-to-point and multidrop communications. A differential line driver is an interface IC that converts a single-ended logic signal into a balanced pair of differential signals. In the hierarchy of electronic components, it belongs to the interface IC family, within communication and transceiver devices. Differential signaling improves noise immunity by rejecting common-mode noise and allows reliable data transmission over longer cable runs than ordinary single-ended digital logic. The MC3487DR provides four driver channels rather than a full transceiver, so it does not receive differential data. The output-enable function controls the output state, allowing connected drivers to be disabled when they are not active. This is useful in systems that share a bus or require controlled output states. Power-up and power-down protection are also identified in the manufacturer documentation. Typical uses include industrial RS-422 links, data acquisition systems, test equipment, instrumentation, and multi-channel communication links. The 5 V supply operation simplifies interface design in legacy and industrial systems where the host logic uses a 5 V rail. Because it is a driver-only device, the system designer must provide the receiving circuitry and define cable termination, grounding, and enable-control behavior. The main design considerations are signal integrity, cable length, supply decoupling, and output-state control. Differential pairs should be routed with consistent geometry and appropriate grounding. The output-enable signals should be controlled during reset so that multiple channels do not contend on a shared bus. The device is intended for surface-mount assembly in the 16-pin SOIC package.

RFC Hubungi kami
MC3487J - Quad Differential Driver, 5V, DIP-16 | Texas Instruments
MC3487J

MC3487J - Quad Differential Driver, 5V, DIP-16 | Texas Instruments

The Texas Instruments MC3487J is a quadruple differential line driver operating from one 5 V supply and packaged in a 16-pin dual-in-line package. It provides four independent differential outputs for ANSI TIA/EIA-422-B and ITU Recommendation V.11 interfaces. Each channel uses a buffered TTL-compatible input to reduce loading, while 3-state outputs support shared-bus control. The MC3487J is a through-hole military-temperature-grade DIP-16 option. A differential line driver is an interface IC that converts a TTL-compatible logic signal into a balanced pair of differential signals. The balanced topology helps reject common-mode noise and supports reliable point-to-point data transmission. In the interface hierarchy, the MC3487J belongs to the line-driver family and implements the transmit side of a differential communications link. Its intended counterpart is the MC3486 quadruple line receiver. The MC3487 contains four independent channels, a single 5 V supply architecture, high-impedance inputs, and 3-state outputs. The official product description identifies these features as supporting reduced input current and minimized loading. Power-up and power-down protection are also listed in the device literature. The verified distributor data identifies the MC3487J as a military-temperature-grade, through-hole, 16-terminal rectangular DIP, but does not provide all timing, output-current, or temperature limits. Each output is intended for a balanced differential connection rather than a single-ended RS-232-style signal. Because outputs can enter a high-impedance state, the device can participate in bus-direction or driver-enable control when the system requires it. Designers must still account for the differential network, termination strategy, unused inputs, and the voltage levels required by the connected receiver. Exact propagation delay, transition time, output impedance, and common-mode limits require the manufacturer datasheet. Typical uses include industrial instrumentation, computer peripherals, point-to-point data links, test equipment, and legacy communications interfaces. In a transmitter design, the MC3487J sits between a TTL/CMOS-compatible control circuit and a balanced cable or board trace. The receiving end can use an MC3486 or another compatible differential receiver. Keep the driver close enough to the connector or transceiver boundary that unbalanced stub lengths remain short and the cable transition is clean. The principal design consideration is verifying the 5 V rail and every connected differential input against the device electrical limits before layout release. Decoupling should follow the manufacturer guidance, and unused inputs must not be left in an undefined state if they can affect system behavior. The MC3487J is appropriate when a legacy, balanced, TTL-driven interface is required and a through-hole DIP-16 assembly is preferred over a surface-mount package. This page consolidates the verified Texas Instruments product description, manufacturer datasheet link, package information, distributor price indication, and application-oriented design guidance. It also separates verified facts from parameters that still require confirmation in the datasheet, helping engineers make an evidence-based sourcing decision.

RFC Hubungi kami