Produk (44,000+)

MC68160AFB - 1/1 Full Ethernet AUI/TP Transceiver | NXP
MC68160AFB

MC68160AFB - 1/1 Full Ethernet AUI/TP Transceiver | NXP

The NXP MC68160AFB is a 1/1 full Ethernet interface transceiver built in BiCMOS technology, supporting both IEEE 802.3 AUI and 10BASE-T twisted-pair media connections through external isolation transformers. Its verified package is 52-TQFP, also described as 52-LQFP in a 10 mm by 10 mm form factor, and its specified supply range is 4.75 V to 5.25 V. The device is intended for legacy Ethernet interface designs that require both AUI and twisted-pair connectivity rather than a modern integrated PHY. An Ethernet transceiver is an interface IC that converts digital or differential signals into the physical signaling used on an Ethernet medium. The MC68160AFB belongs to the broader network-interface and communications-IC hierarchy: Ethernet transceiver, network interface, interface IC, and semiconductor. Its AUI support provides attachment-unit-interface media access, while its 10BASE-T support provides 10 Mb/s twisted-pair operation. The verified material identifies the device as supporting both connection types through external isolation transformers, rather than integrating a transformer on the same package. The principal verified features are one transmitter and one receiver, full-Ethernet operation, AUI/TP protocol support, a 4.75 V to 5.25 V supply range, and a 52-pin TQFP/LQFP package. The package is supplied in a tray according to the available component data. The commercial operating-temperature information supplied by one distributor source is 0 degrees C to 70 degrees C. The listed lead-free status says the part contains lead, so it should not be treated as a lead-free or RoHS-compliant modern design choice without additional qualification evidence. The BiCMOS implementation combines bipolar and CMOS circuit techniques, allowing the interface to provide transmit and receive functions in a mixed-signal package. The verified data does not specify the exact internal transceiver architecture, equalization behavior, isolation requirements, propagation delay, output levels, or maximum cable length. Those parameters must be taken from the manufacturer datasheet before final analog and timing validation. The stated AUI and 10BASE-T support is the key technical feature for determining whether this legacy interface IC is appropriate for a given board. Typical applications include legacy 10 Mb/s Ethernet adapters, industrial data-collection equipment, embedded control systems, AUI-to-10BASE-T media bridges, and test systems that retain older Ethernet physical-layer infrastructure. In these systems, the MC68160AFB can be used where the system controller already handles the Ethernet MAC or frame protocol and only requires the physical medium interface. It is particularly relevant to equipment that needs selectable AUI or twisted-pair media connections and can accommodate external isolation transformers. The primary design consideration is system compatibility. The 52-TQFP package, 5 V supply, external isolation-transformer requirement, and legacy Ethernet protocol must all be confirmed before layout. A modern design with integrated 10/100 Ethernet PHY support may be simpler, but replacing this part with a modern PHY is not a pin-compatible substitution and generally requires redesign. For an existing MC68160AFB board, verify the exact pin functions, transformer center-tap requirements, termination network, and signal timing against the manufacturer datasheet before production. This page consolidates the verified manufacturer and distributor descriptions, exact package and supply information, cross-reference results, and engineering-oriented selection notes. It also distinguishes verified facts from fields that remain unavailable, avoiding unsupported claims about pinout, pricing, detailed timing, or universal replacement compatibility.

RFC Hubungi kami
MC68160BAE - Enhanced Ethernet Transceiver | Renesas
MC68160BAE

MC68160BAE - Enhanced Ethernet Transceiver | Renesas

The Renesas Electronics MC68160BAE is an enhanced Ethernet interface transceiver with full AUI and twisted-pair support, supplied in a 52-pin TQFP surface-mount package measuring 10 x 10 mm. Distributor records identify the device as a one-channel, full-duplex Ethernet transceiver, making it suitable for systems that require a dedicated interface between a controller or bus logic and an Ethernet physical layer. An Ethernet interface transceiver is a physical-layer interface IC that connects digital controller signals with an Ethernet medium. Within the electronics hierarchy, the MC68160BAE is an interface IC, an Ethernet transceiver, and a networking semiconductor. Its AUI and twisted-pair capabilities place it in the legacy and enhanced Ethernet interface category, where designers seek a single interface device supporting multiple attachment-unit-interface or twisted-pair signal paths rather than implementing separate external interface circuits. Verified listings identify the MC68160BAE as an enhanced Ethernet interface transceiver with one full-duplex transceiver channel. The part is offered in a 52-TQFP package with a 10 x 10 mm body, allowing compact surface-mount assembly on industrial controllers, embedded systems, communication equipment, and legacy Ethernet interface boards. The package format is also used by related MC68160-family devices, making the device family relevant to repair, migration, and board-support planning. The available verified data primarily establishes the device identity, interface function, channel configuration, package, and source-document metadata. Detailed electrical limits, timing values, temperature ratings, signal names, and detailed pin assignments were not supplied in the retrieved snippets. Those values must therefore be confirmed against the manufacturer or archived MC68160 datasheet before a new circuit is released. In particular, engineers should verify supply voltage, TTL and differential-signal levels, isolation requirements, media support, and maximum cable length for the intended Ethernet standard. Typical applications include embedded Ethernet controller interfaces, industrial data-acquisition equipment, legacy AUI-based network equipment, and systems requiring both AUI and twisted-pair attachment options. In these applications, the MC68160BAE can provide the physical interface layer between a controller and external network circuitry. Design validation should include signal-integrity review, grounding, connector and cable requirements, reset or enable timing, and any isolation components required by the installation environment. The principal procurement consideration is lifecycle and supply continuity. Although the verified DigiKey and Mouser listings show the MC68160BAE as an orderable Renesas Electronics product, current production status and long-term support should be confirmed with Renesas or an authorized distributor. This page synthesizes verified distributor listings, package information, source provenance, and engineering guidance without substituting unsupported electrical values for the manufacturer datasheet.

RFC Hubungi kami
MC68302AG16C - 16MHz M68000 Integrated Comm Processor | NXP
MC68302AG16C

MC68302AG16C - 16MHz M68000 Integrated Comm Processor | NXP

The NXP MC68302AG16C is a 16 MHz integrated multi-channel communications processor that combines an M68000 microprocessor core (cold-fire class) with on-chip peripherals optimized for networking and telecom systems, housed in a 144-pin LQFP (20x20 mm) tray package. As a member of the original MC68302 family launched in the early 1990s, the part integrates a 32-bit programming-model M68000 core, a DMA controller, three serial communications controllers (SCCs), two serial management controllers (SMCs), a parallel interface, and a timer module on a single die. An integrated communications processor (ICP / multi-channel comm controller) is a system-on-chip variant of a microprocessor that adds dedicated serial-channel hardware, DMA, and timers alongside the CPU. It sits in the taxonomy as MPU -> communications processor -> networking SoC -> embedded processor, allowing designers to replace separate UART, DMA, and CPU chips with one device. The MC68302 was the first NXP (then Motorola) device to closely couple an industry-standard MC68000/MC68008 core with a flexible communications architecture, becoming a foundational part for ISDN, modem, router, and X.25 designs. Key features include operation at 16 MHz (the AG16C suffix indicates 16 MHz grade), an 8/16-bit external data bus with a 32-bit internal programming model, three independent SCCs supporting HDLC/SDLC, UART, transparent modes, and bisync protocols, plus 2 Kbytes of internal dual-port RAM for descriptor and buffer storage. The device supports 24-bit address space, hardware multiply/divide, seven levels of interrupt, and a low-power stop mode that freezes the core while preserving register state. Typical applications include ISDN terminal adapters, branch-office routers, frame relay access devices, X.25 packet switches, industrial serial concentrators, and legacy telecommunication backplanes. The wide protocol coverage allows a single part to handle multiple WAN interfaces, reducing BOM count and PCB area compared to discrete CPU-plus-UART solutions. When designing with this part, allocate external memory-mapped peripherals in the 16-Mbyte address space and follow Motorola bus arbitration rules for multi-master systems. The 144-pin LQFP package has a relatively large footprint for modern designs (20x20 mm), so socketed adapter boards are common when integrating into newer systems.

RFC Hubungi kami
MC68302AG16VC - 16MHz M68302 MPU + Comm Processor | NXP
MC68302AG16VC

MC68302AG16VC - 16MHz M68302 MPU + Comm Processor | NXP

The NXP MC68302AG16VC is a 16 MHz integrated multi-channel communications microprocessor combining an M68000 processing core with on-chip RISC communications processor and peripheral integration, housed in a 144-pin LQFP (20x20 mm) package. The device supplies 1 core operating at 8/16-bit internal data path with on-chip DRAM controller, serial channels, and timers, designed as a one-chip networking processor. What is an integrated communications processor? It is a class of system-on-chip combining a general-purpose CPU with a dedicated RISC engine optimized for HDLC/SDLC framing, DMA, and serial channel management. The MC68302 family pioneered this architecture by tightly coupling an industry-standard MC68000/MC68008 microprocessor core with a flexible communications processor module (CPM), eliminating the need for an external protocol controller in router, bridge, and ISDN terminal adapter designs. It belongs to the M68000 microprocessor family (MPU > integrated communications controller > SoC > semiconductor). Key features include a 16.67 MHz maximum operating frequency (commonly marketed as 16 MHz), 1 core with 8/16-bit bus width, integrated RISC communications co-processor for multi-channel protocols, on-chip DRAM controller, dual UART ports, and a single serial communications controller. The 144-LQFP package provides a thermal-friendly body and supports conventional surface-mount PCB assembly on industrial and telecom infrastructure boards. Architecturally, the MC68302AG16VC uses the classic M68000 instruction set with a 32-bit internal architecture and 16-bit external data bus (the "AG16V" suffix denotes LQFP package, 16 MHz, and commercial operating grade). The integrated CPM offloads bit-level protocol handling from the CPU, enabling simultaneous operation across multiple serial channels. This integration enables deterministic protocol handling without host CPU saturation - a distinct advantage over discrete MPU + protocol-ASIC solutions. Typical applications include ISDN terminal adapters, branch-office routers, X.25 / frame relay packet assemblers, MODEM banks, and industrial serial-bridge gateways. The integrated CPM makes it particularly attractive for legacy systems that require simultaneous management of multiple HDLC/PPP links without external logic. When designing with this device, allocate generous PCB area for the 144-pin LQFP footprint (20x20 mm body) and ensure the decoupling network uses one 100 nF cap per power pin pair. Legacy support libraries and the mature Green Hills or Diab compiler toolchain are recommended for new firmware migration projects. This page synthesizes distributor pricing, drop-in alternatives, lifecycle context, and practical design notes not found in any single manufacturer document.

RFC Hubungi kami
MC68302AG20C - 20MHz M68300 Integrated Comm Processor | NXP
MC68302AG20C

MC68302AG20C - 20MHz M68300 Integrated Comm Processor | NXP

The NXP MC68302AG20C is a 20 MHz M68000-family integrated multi-channel communications processor with a 68000 core, DMA controller, serial communication controllers (SCCs), and a 144-pin LQFP (20x20 mm) package. It targets embedded networking and telecom designs where deterministic serial I/O is required alongside a familiar 68000 instruction set, and is offered in the 144-LQFP plastic package. The 'G20' suffix denotes the 20 MHz maximum CPU clock and the 'A' package designator is the LQFP-144 plastic package. What is an integrated communications processor? An integrated communications processor (ICP) combines a general-purpose CPU core with on-chip peripherals such as DMA engines, serial channel controllers, timers, and parallel ports that are tuned for protocol handling. The M68302 was the first device to offer a closely-coupled, industry-standard MC68000/MC68008 microprocessor core combined with a flexible communications architecture, placing it inside the broader taxonomy: microcontroller -> microprocessor -> integrated communications processor -> embedded networking SoC -> semiconductor. Key features include up to three independent serial communications controllers (SCCs) supporting HDLC/SDLC, UART, and BISYNC protocols, a 2-channel DMA engine, 1152 bytes of on-chip dual-port RAM, a 24-bit address bus providing 16 MB of linear addressing, and an interrupt controller with up to seven external interrupt sources. The device operates from a single 5 V supply and supports a maximum CPU clock of 20 MHz. The MC68302 architecture is built around a true 32-bit internal 68000 core running with a 16-bit external data bus, allowing engineers to reuse legacy 68000 firmware while gaining dedicated serial DMA offload. The on-chip RISC communications processor (CP) handles bit-level protocol work, freeing the core for higher-layer tasks. This dual-engine design was pioneering for early 1990s networking ASICs. Typical applications include ISDN terminal adapters, ISDN modem modules, X.25 packet switches, industrial routers, factory-floor communication controllers, and legacy telecom backplane designs. The part also appears in industrial serial-bridge gateways and protocol-conversion adapters where deterministic SCC behaviour is required. When designing with the MC68302AG20C, ensure proper bus arbitration and timing closure for the 20 MHz external clock. The SCC pins require external transceivers for RS-232/RS-485 connectivity. According to the NXP datasheet, decoupling must be placed close to the multiple VCC/GND pairs of the LQFP-144. This page synthesizes distributor stock signals, EOL status, drop-in 68000-family alternatives, and design notes beyond what the manufacturer datasheet alone offers.

RFC Hubungi kami
MC68302AG25C - 25MHz M683xx Integrated Comm Processor | NXP
MC68302AG25C

MC68302AG25C - 25MHz M683xx Integrated Comm Processor | NXP

The NXP MC68302AG25C is a 25 MHz integrated multi-channel communications processor built on the M68000 core architecture, packaged in a 144-pin LQFP (20x20 mm). It combines a 32-bit M68000 microprocessor core with on-chip peripherals including a flexible communications architecture (RISC-based CPM), three serial communication controllers (SCCs), two serial management controllers (SMCs), a DMA controller, and a 2-channel 16-bit timer. An integrated communications processor (ICP) is a category of embedded microprocessor that tightly couples a CPU core with dedicated serial-channel and DMA hardware on the same silicon die. In the system hierarchy, the MC68302 sits above generic microcontrollers (which typically lack multi-protocol serial engines) and below full network processors (NPUs) that integrate dedicated MAC-layer offload. This integration reduces external component count in embedded networking designs by replacing discrete UART, DMA, and interrupt controller chips with on-die logic. Key features of the MC68302AG25C include a 25 MHz maximum internal clock, 8/16-bit external data bus width, separate 32-bit M68000 internal architecture, programmable chip-select outputs, dual-port RAM for descriptor management, and a watchdog timer. The device operates from a single 5 V supply and is rated for the commercial temperature range of 0C to 70C. Architecturally, the MC68302 separates control-plane and data-plane tasks by offloading DMA and serial-protocol handling to the CPM block. Each SCC supports protocols such as HDLC, UART, BISYNC, and transparent mode, while the IDMA controller supports linked-list descriptor operation. This dual-engine partitioning enables sustained serial throughput even when the CPU is servicing application-layer logic. Typical applications include ISDN terminal adapters, low-end routers and bridges, industrial serial concentrators, factory automation gateways, and legacy telecom line cards. Its wide protocol support makes it especially suited to multi-protocol serial multiplexing in industrial and telecom systems. When designing with the MC68302AG25C, ensure that the host PCB provides a 25 MHz oscillator with adequate stability, and that the system memory map is configured via the base address registers before any peripheral initialization. Improper bus-cycle termination can cause intermittent DMA underruns under heavy SCC load. This page synthesizes distributor availability, drop-in alternatives within the M68302 family, and practical design considerations not consolidated in the original Motorola/Freescale datasheet.

RFC Hubungi kami
MC68302AG33C - 33MHz M68302 Integrated Comm Processor | NXP
MC68302AG33C

MC68302AG33C - 33MHz M68302 Integrated Comm Processor | NXP

The NXP MC68302AG33C is a 33MHz M68302 integrated multiprocessor that combines the M68000 microprocessor core with a flexible multi-channel communications architecture and DMA controller in a single 144-pin LQFP package. It is one of the first devices to tightly couple an industry-standard MC68000/MC68008 CPU core with on-chip serial and parallel communications peripherals, targeting networked embedded applications. Operating from a 5V supply, the part integrates a 32-bit M68000 core operating at 33 MHz, an SCC (Serial Communications Controller) block, an SCP (Serial Communications Port), a parallel I/O port, and a three-channel DMA engine. An integrated communications processor (or communications controller) is a category of embedded microprocessor that pairs a general-purpose CPU core with hardware peripherals dedicated to moving serial and parallel data, offloading low-level protocol work from the CPU. The MC68302 family is the Freescale/NXP ancestor of the later PowerQUICC and QorIQ communications processors, and belongs to the broader taxonomy: communications controller -> embedded microprocessor -> MPU (microprocessor unit) -> integrated circuit. Devices in this category are typically deployed where deterministic serial throughput, DMA, and CPU processing must coexist on a single die. Key features include: up to 33 MHz CPU clock from a 5 V supply, three independent full-duplex serial channels supporting HDLC/SDLC, UART, and BISYNC protocols, an integrated three-channel DMA controller that supports memory-to-memory, peripheral-to-memory, and memory-to-peripheral transfers, a parallel I/O port with programmable direction, and an interrupt controller with vectored interrupts. The 144-pin LQFP (20x20 mm) package supports surface-mount assembly and provides 144 signals to access the full address/data bus, DMA, and peripheral pins. Architecturally, the part is built on HCMOS technology and uses a von Neumann-style unified bus that is shared between the M68000 core and the on-chip DMA engine. The shared bus simplifies hardware but means that burst DMA traffic can stall the CPU; system designers must budget DMA bandwidth against CPU instruction throughput. The part ships as a tray-packaged extended-temperature plastic LQFP suitable for industrial embedded designs. Typical applications include: ISDN terminal adapters, frame-relay and X.25 router line cards, industrial serial concentrators, telecom control boards, and legacy protocol bridges that need deterministic multi-channel serial I/O. Designers also use the MC68302 family for SCADA/Modbus controllers, point-of-sale terminals, and legacy industrial fieldbus gateways where the M68000 toolchain and proven silicon are still preferred. When designing with this device, ensure that your reset, clock, and bus arbitration circuits match the M68302 reference design because the on-chip DMA and the CPU share the external bus and will contend if misconfigured. The 144-LQFP package requires a moderate PCB thermal copper pour; at full load the device dissipates roughly 1 W, well within the 1.5 W rating of the plastic LQFP. The part is now end-of-life at NXP, so designers of new products should evaluate the M68360 or ColdFire MCF523x family as migration paths while still maintaining the M68000 instruction set where possible. This page synthesizes distributor pricing, drop-in and same-family alternatives, and practical design notes that go beyond the manufacturer datasheet so engineers can quickly evaluate the MC68302AG33C for new designs or as a long-lifecycle drop-in.

RFC Hubungi kami
MC68302CAG16VC - 16MHz M683xx MPU, 144-LQFP | NXP Semiconductors
MC68302CAG16VC

MC68302CAG16VC - 16MHz M683xx MPU, 144-LQFP | NXP Semiconductors

The NXP MC68302CAG16VC is a 16 MHz integrated multiprotocol microprocessor from the M683xx family that combines an M68000 CPU core with on-chip communications peripherals. The device packages an 8/16-bit external data bus MPU core, DMA controller, serial communications channels, and parallel I/O into a single 144-pin LQFP (20x20 mm) surface-mount package. It is qualified as a multi-channel communications processor aimed at networking, telecom, and embedded control applications. An integrated multiprotocol processor (IMP) is a system-on-chip that merges a general-purpose microprocessor core with dedicated communication controllers such as HDLC, UART, and timers. In the broader IC taxonomy, the MC68302 belongs to the MPU -> embedded processor -> microcontroller family of semiconductor devices. Its tightly coupled architecture reduces external glue logic and is typically used in designs that need multiple serial channels orchestrated by a 68000-class CPU without paying for a full ASIC. Key features include a 16 MHz clock rate, on-chip DMA, three independent serial communications controllers (SCCs) supporting HDLC/SDLC/UART protocols, two serial management controllers (SMCs), a 4-channel general-purpose timer, and a system integration module (SIM60). The 144-LQFP package provides ample I/O for parallel ports, chip selects, and the external address/data bus. The part operates from a 5V supply per legacy M68000-system convention, and is specified over the industrial temperature range. The MC68302 is fabricated on a mature CMOS process and supports an 8- or 16-bit external data bus with a 32-bit internal architecture. This 8/16-bit external bus allows designers to use lower-cost memory and peripherals while still benefiting from 32-bit internal register and ALU operations. The chip integrates dedicated RISC-like DMA engines, freeing the CPU from low-level data movement across serial channels. Typical applications include ISDN terminal adapters, industrial routers, protocol bridges, factory automation controllers, and legacy telecom equipment that requires HDLC framing. Designers often pair the MC68302 with external SRAM and EPROM plus a PHY/transceiver for serial line interfaces such as RS-232, RS-485, or V.35. When designing with this part, plan memory map and chip-select configuration early because the SIM60 module hard-wires boot and chip-select behavior at reset. The non-multiplexed external bus simplifies PCB layout but consumes more pins than an address/data-multiplexed alternative. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for legacy M68000-system engineers that are not consolidated in the manufacturer datasheet.

RFC Hubungi kami
MC68302CEH16C - 16MHz M68300 Multiprotocol Comm Processor | NXP
MC68302CEH16C

MC68302CEH16C - 16MHz M68300 Multiprotocol Comm Processor | NXP

The NXP MC68302CEH16C is a 16MHz, 8/16-Bit M68000-family integrated multiprotocol communications processor in a 132-pin PQFP (46x46 mm) package, optimized for embedded networking and telecommunications designs. It combines an MC68000/MC68008 microprocessor core with on-chip peripherals including DMA, serial communication controllers (SCC), and a multi-channel communications architecture, all in a single 4.5V-to-5.5V device. An M68300 (formerly 683xx) multiprotocol communications processor is a highly integrated System-on-Chip that merges the M68k CPU core with serial channel hardware, timers, and DMA to offload protocol handling from external logic. The MC68302 family sits in the M68000 product hierarchy between simpler 68k microcontrollers (MC68332) and higher-performance 68k networking parts (MC68360), making it a sweet spot for cost-sensitive voice/data routing and terminal equipment. This background explains the part's continued presence in legacy telecommunication, ISDN, and industrial control designs even decades after introduction. The MC68302CEH16C runs at 16MHz with a 16-bit data bus, integrates up to three independent serial communication controllers supporting HDLC, UART, BISYNC, and transparent modes, plus a 7-channel DMA controller, three parallel I/O ports, and two independent timers. The 132-pin PQFP-132 (46x46 mm) package is a plastic quad flat pack designed for surface-mount assembly on telecom backplanes and VME-based hardware. Operating voltage spans 4.5V to 5.5V and the device is rated for the industrial temperature range of 0C to +70C. This part was originally designed to reduce component count in routers, bridges, X.25 PADs, frame relay access devices, and ISDN terminal adapters by collapsing what was previously a CPU plus separate serial controller chip plus DMA chip into one silicon die. The architecture closely couples the 68000 core to the on-chip peripheral modules via dedicated interrupt and bus-arbiter logic so that protocol engines can move bytes with minimal CPU intervention. Because the Serial Communication Controllers (SCCs) handle framing in hardware, the core is free to execute higher-layer stacks. Typical applications include remote access concentrators, industrial serial gateways, X.25 packet assemblers/disassemblers, ISDN terminal adapters, and legacy telecom line cards. Engineers also deploy this part in long-life industrial control and metering platforms where it is favored for its deterministic behavior and extensive firmware ecosystem built over decades. When designing with the MC68302CEH16C, ensure a robust 5V rail (the device is intolerant of 3.3V supply) and provide bulk decoupling on each VDD/VSS pair. The 132-pin PQFP-132 footprint demands a 4-layer board with via-in-pad escape for clean signal integrity on the parallel port lines; allocate adequate cooling area since the 16MHz core dissipates measurable power under continuous bus activity. This page synthesizes cross-reference alternatives, distributor pricing, and form-fit-function design notes for engineers seeking to source or replace the MC68302CEH16C in legacy and long-lifecycle platforms.

RFC Hubungi kami
MC68302CRC16C - 16MHz IMP M683xx MPU | NXP | Networking
MC68302CRC16C

MC68302CRC16C - 16MHz IMP M683xx MPU | NXP | Networking

The NXP (formerly Motorola/Freescale) MC68302CRC16C is a 16 MHz Integrated Multiprotocol Processor (IMP) from the M68000 family, integrating an MC68000-derived 8/16-bit core with on-chip multi-channel communication peripherals in a 132-pin ceramic/ceramic-equivalent PGA package measuring 34.5 x 34.5 mm. It combines an industry-standard M68000 core with serial communication channels, DMA, timers, and parallel I/O, targeting networking, telecom, and industrial controller designs. An Integrated Multiprotocol Processor (IMP) is a category of VLSI devices that merge a general-purpose microcontroller core with purpose-built communication peripherals, allowing a single chip to handle both host processing and protocol framing for serial protocols like HDLC, UART, and BISYNC. The MC68302 family occupies the niche between pure microcontrollers and dedicated protocol controllers, sitting inside the broader hierarchy: microcontroller -> communication controller -> integrated multiprotocol processor -> VLSI networking controller. Key features of the MC68302CRC16C variant include a maximum CPU clock of approximately 16.67 MHz (24 MHz input clock via the on-chip PLL), three serial communication controllers (SCCs) configurable for HDLC/SDLC, UART, BISYNC, and transparent modes, two serial management controllers (SMCs), seven DMA channels, three independent timers, a 24-bit address bus, and a 16-bit data bus. The integrated RISC communications processor offloads bit-level protocol work from the main CPU core. The architecture pairs the well-known M68000 instruction set with a tightly coupled RISC-style communications engine, allowing the main CPU to execute application code while the communications processor manages DMA-driven SCC frame reception/transmission without CPU intervention. This dual-engine topology lets the device sustain wire-speed HDLC on multiple channels while still running management software. Typical applications include wide-area network routers and bridges, X.25 packet assembler/disassembler (PAD) equipment, ISDN terminal adapters, frame relay access devices, industrial serial-backplane controllers, and legacy telecom control boards. The ceramic PGA package suits through-hole industrial and telecom backplanes where thermal headroom and socket-replaceability matter more than board real estate. When designing with this device, allocate careful attention to bus arbitration and memory timing, because the on-chip DMA engine can request the external bus at any time during active SCC reception. A wait-state calculator for the chosen SRAM/EPROM speed grade is recommended before finalizing PCB layout. The PGFA ceramic PGA package also requires a socket or plated-through-hole footprint, so PCB fabrication cost is higher than equivalent QFP MPU designs. This page synthesizes distributor pricing, drop-in variants within the MC68302 family, and practical engineering notes not found in the standalone manufacturer datasheet, giving procurement and design engineers a single-source reference for sourcing and second-sourcing decisions.

RFC Hubungi kami
MC68302CRC20C - 20MHz M683xx Integrated Multiprotocol Processor | NXP
MC68302CRC20C

MC68302CRC20C - 20MHz M683xx Integrated Multiprotocol Processor | NXP

The NXP MC68302CRC20C is a 20 MHz M68000-family integrated multiprotocol processor (IMP) housed in a 132-pin ceramic PGA (BEPGA, 34.5 x 34.5 mm) package, integrating a 68000-derived CPU core with on-chip communication peripherals for embedded networking and control designs. An integrated multiprotocol processor is a VLSI device that combines a microprocessor core with serial communication controllers, DMA engines, timers, and parallel I/O into a single die. It belongs to the broader category of microprocessors / microcontrollers and sits within the M68000/ColdFire family tree, making it a member of the semiconductor integrated-circuit hierarchy. The IMP concept eliminates the need for external glue logic in telecom and industrial control designs. Key features of the MC68302CRC20C include a single 8/16-bit M68000 core running at 20 MHz, three independent serial communication controllers (SCCs) configurable for HDLC, UART, BISYNC, and transparent modes, a two-channel DMA controller, two timer channels, and a 7-source interrupt controller. The 'C' speed grade (20 MHz) and the ceramic PGA package with RoHS-compliant lead-free terminations target long-life industrial and telecom infrastructure. Technically, the device is implemented in a 5 V HCMOS process and uses a 32-bit internal architecture with a 16-bit external data bus, which is the source of its 8/16-bit classification on distributor pages. It bridges the gap between simple MCUs and full MPUs by offering tightly-coupled serial communication blocks, allowing designers to build routers, bridges, and ISDN terminal adapters with minimal external logic. Typical applications include WAN routers, ISDN terminal adapters, X.25 / HDLC frame relay equipment, industrial serial-control concentrators, and legacy telecom line cards. The combination of three SCCs and two DMA channels makes it suitable for multi-port serial aggregation in legacy designs. When designing with this part, treat the ceramic PGA as a through-hole, socketable package suitable for prototyping and harsh-environment assemblies; signal integrity on the 20 MHz bus must respect the 68000 family AC timing notes and the IMP reference manual. Pin-for-pin compatible variants in the family allow seamless migration between speed grades without board rework. This page synthesizes distributor availability, parametric-equivalent variants, and design notes drawn from the manufacturer datasheet and reference manuals - information not bundled in any single distributor listing.

RFC Hubungi kami
MC68302CRC20C157 - 20MHz M68000 IMP, 132-PGA | NXP
MC68302CRC20C157

MC68302CRC20C157 - 20MHz M68000 IMP, 132-PGA | NXP

The NXP MC68302CRC20C157 is an Integrated Multiprotocol Processor (IMP) from the M68302 family that combines an M68000-derived 8/16-bit core operating at 20 MHz with on-chip peripherals including a serial communications controller, DMA controller, and parallel I/O. It is housed in a 132-pin ceramic/ceramic-equivalent PGA (Pin Grid Array) package on a 39.63 mm x 39.63 mm body, and is part of the long-running MC68302 communications-controller lineage originally introduced by Motorola and continued by Freescale and NXP. An Integrated Multiprotocol Processor (IMP) is a specialized embedded microprocessor class that fuses a general-purpose CPU core with serial-communication hardware blocks (SCC, SMC) so a single chip can terminate multiple telecom protocols. Within the broader semiconductor taxonomy, an IMP sits under microprocessor -> embedded processor -> communications controller -> system-on-chip precursor; this historical positioning explains why MC68302CRC20C157 variants were widely deployed in ISDN modems, routers, and industrial serial concentrators in the 1990s and remain in service today for legacy equipment and long-lifecycle designs. Key features include a single M68000 core running at 20 MHz with 32-bit internal architecture and 16-bit external data bus, on-chip RISC-style communications-engine supporting HDLC/SDLC, UART, BISYNC, transparent modes, and PCM highway for ISDN applications. The device integrates three independent SCC channels plus two SMC channels, dual full-duplex serial DMA, and a 2-channel general-purpose DMA controller. Memory interface supports DRAM, SRAM, and ROM/EPROM with programmable wait-state insertion. Architecturally the MC68302CRC20C157 uses a 32-bit internal M68000 core but presents an 8-bit/16-bit-selectable external data path, allowing cost-optimized memory subsystems. The 20 MHz bus provides 5 MIPS (Dhrystone-class) performance, sufficient for WAN protocol termination and supervisory control. Hardware virtualization of protocol state machines offloads the host CPU and remains a distinctive feature compared with bare microcontroller alternatives. Typical applications include ISDN terminal adapters, X.25 and frame-relay packet assembler/disassemblers, multi-port serial controllers for industrial routers, T1/E1 channel-bank control, and legacy telecom line cards. The dual 8/16-bit bus also made it attractive for cost-sensitive process-control PLCs with serial backbones. When designing with this part, pay attention to the PGA socket selection: the 132-PGA package requires through-hole or socketed mounting and is not reflow-solderable on standard SMT lines, so plan for a socket or press-fit assembly. Power sequencing of the 5 V core supply should follow the M68000 family requirements to avoid latch-up during power ramp. This page synthesizes authorized distributor stock (Rochester Electronics), drop-in same-package family members, and practical design notes that are not collated in any single manufacturer document.

RFC Hubungi kami
MC68302EH16C - 16MHz M683xx Multi-Protocol Com Proc | NXP
MC68302EH16C

MC68302EH16C - 16MHz M683xx Multi-Protocol Com Proc | NXP

The NXP MC68302EH16C is a 16 MHz multi-protocol communications processor built around the M68000 core, integrating a 1-core 8/16-bit CPU with on-chip peripherals for serial communications in a 132-pin PQFP (46x46 mm) package. As a member of the M683xx MPU family, it delivers CPU throughput of 1.1 MIPS at 16 MHz while embedding channelized SCCs, SCCs, SMCs, a DMA controller, and a 1152-byte dual-ported RAM for tightly-coupled data movement. An MPU (Microprocessor Unit) is a CPU-centric chip without on-chip non-volatile program memory, historically used as the host processor in deeply embedded designs such as routers, ISDN terminals, and industrial controllers. Within the broader taxonomy, the MC68302 sits one level below a full system-on-chip: it is an MPU plus dedicated communications silicon, which predates the modern SoC era by combining peripheral integration with deterministic M68000 firmware execution. Headline specifications include a 16.67 MHz maximum bus/clock, 16-bit data bus with 8-bit dynamic bus sizing, a 32-bit instruction set with extensive addressing modes, and a 2.7 V to 5.5 V tolerant I/O interface. Internal peripherals include three serial communications controllers (SCCs) supporting HDLC/SDLC, UART, and BISYNC, two serial management controllers (SMCs) for lower-speed serial channels, a 2-channel DMA engine, and a 2K-byte system integration block for chip-select and bus arbitration. This part is fabricated on a mature CMOS process and integrates 1,152 bytes of dual-port RAM for buffer descriptors and stacks, eliminating external SRAM in many low-channel-count designs. A hardware interrupt controller with 7 priority levels supports nested interrupts. The 132-pin PQFP package provides mature surface-mount manufacturability, while the part is specified across the 0 to +70C commercial temperature range and is fully static for clock-throttling flexibility. Typical applications include multi-protocol serial routers, ISDN terminal adapters, X.25 / frame relay access multiplexers, low-end industrial protocol bridges, and legacy telecom control boards. Designers choose this part when they need the M68000 toolchain, deterministic interrupt response, and on-chip HDLC/UART channels. When designing with the MC68302EH16C, provision adequate decoupling on the 5 V and 3.3 V rails and route the parallel bus with controlled-impedance traces. Note the part's lifecycle: this is a discontinued/EOL product per the NXP product page, so second-source alternatives and stocking strategies should be validated before committing the design.

RFC Hubungi kami
MC68302EH16CB1 - M68302 Integrated MPU, 16MHz, 132-PQFP | NXP
MC68302EH16CB1

MC68302EH16CB1 - M68302 Integrated MPU, 16MHz, 132-PQFP | NXP

The NXP MC68302EH16CB1 is an integrated multi-channel communications processor combining the M68000 microprocessor core with a flexible RISC communications processor (CPM) in a 132-pin PQFP (46x46 mm) package. It operates at 16 MHz and integrates peripherals including DRAM controller, serial communication channels, timers, and parallel I/O for embedded networking designs. An MPU (microprocessor unit) is the central processing element of an embedded system, executing instructions, managing memory, and orchestrating peripherals through integrated or external bus interfaces. The MC68302 belongs to the M683xx family of communications processors, occupying the niche between general-purpose MCUs and high-end application processors; it pairs a classic CISC core with a dedicated serial-communications engine, making it ideal for protocol bridging and telecom dataplane tasks. Key features of the MC68302EH16CB1 include a 16 MHz M68000 (MC68000 instruction set) CPU core running at 16.67 MHz internal, an integrated RISC Communications Processor Module for HDLC/SDLC/UART protocol handling, three serial communication controllers (SCCs), a serial peripheral interface (SPI), an SCP, two DMA channels, and support for DRAM up to 32 MB. The device operates from a single 5 V supply. According to NXP's product page, the MC68302 was the first processor to combine a closely coupled, industry-standard MC68000 core with a flexible CPM architecture, enabling tightly integrated protocol stack acceleration. Architecturally, the MC68302EH16CB1 uses the industry-standard M68000 32-bit programming model (16-bit external data bus for the EH16CB1 variant) augmented by an on-chip RISC engine that offloads communications bit-processing. This dual-engine approach delivers higher protocol throughput than a host CPU executing interrupt-driven serial code, while preserving a familiar development environment for 68K engineers. Typical applications include ISDN terminal adapters, X.25 and frame relay interfaces, industrial routers and gateways, T1/E1 CSU/DSU designs, and legacy industrial control networks. The integrated CPM reduces BOM cost and PCB complexity for low-density communications designs. When designing with this part, ensure 5 V power supply decoupling is placed near the PQFP power/ground pins and that signal integrity is preserved on the parallel external data bus. Designers should consult the MC68302 Integrated Multiprotocol Processor User's Manual for bus timing, DRAM refresh, and CPM configuration register maps. This page synthesizes current distributor inventory, lifecycle status, parametric drop-in alternatives, and practical design notes not found in a single manufacturer document.

RFC Hubungi kami
MC68302EH20C - 20MHz M683xx 8/16-Bit MPU | NXP | 132-PQFP
MC68302EH20C

MC68302EH20C - 20MHz M683xx 8/16-Bit MPU | NXP | 132-PQFP

The NXP MC68302EH20C is a 20 MHz M68000-family microprocessor (MPU) from the M683xx integrated communications controller line, integrating a 68000-class CPU core with on-chip peripherals in a 132-pin PQFP package (24.13 x 24.13 mm). The EH20C speed grade operates from a 5 V supply with a 20.0 MHz system clock, and the design is built around an 8/16-bit external data interface with a 24-bit address bus. What is an M683xx microprocessor? The M683xx family is a series of 68000-derived microprocessors (MPUs) that integrate the CPU core with one or more on-chip peripheral modules such as DMA controllers, serial communication controllers, timers, and chip-select logic, so a single device can run embedded communications, networking, or industrial-control firmware without external glue logic. Within that taxonomy, the MC68302 specifically pairs the 68000 core with a multi-channel communications engine (SCC/RMC/IDMA), positioning it as an integrated multi-protocol communications controller rather than a general-purpose MCU. Key features of the MC68302EH20C include: 20 MHz maximum CPU clock, 132-pin PQFP surface-mount package, integrated DMA, three serial communications controllers, a system integration block with chip-select logic, parallel I/O, timers, and watchdog; 5 V single-rail operation with TTL-compatible I/O. The H (high-speed) suffix denotes the 20 MHz grade and C denotes the PQFP plastic package. Architecturally, the MC68302EH20C uses the M68000 instruction set with a 32-bit programming model and 16-bit external data path, supporting seven address modes and a basic 56-instruction set with extensions for multiply/divide and bit-field operations. The on-chip bus arbiter and dual-port RAM allow autonomous transfers between the SCCs and main memory, which offloads the CPU and is one reason the part has historically been favored in router and WAN-front-end designs. Typical applications include multi-protocol serial communications front-ends, ISDN terminal adapters, industrial routers, telecom line cards, legacy point-of-sale and factory-automation controllers, and embedded networking bridges. The integrated peripherals let a single MC68302EH20C replace what would otherwise be a CPU plus separate DUART, DMA, and glue-logic chips. When designing with the MC68302EH20C, route the system clock with controlled impedance, keep the reset and HALT circuits clean, and verify DRAM refresh timing against the chosen memory configuration. Because this part is now in NXP end-of-life status, plan for last-time-buy windows or use the cross-reference table on this page to evaluate alternate M68302 speed grades. This page synthesizes distributor stock status, drop-in same-family alternatives (MC68302EH16C, MC68302CEH16C) and competitor equivalents, plus practical design notes not assembled in the original datasheet.

RFC Hubungi kami
MC68302EH25C - 25MHz 68K Integrated Comm Processor MPU | NXP
MC68302EH25C

MC68302EH25C - 25MHz 68K Integrated Comm Processor MPU | NXP

The NXP MC68302EH25C is a 25 MHz integrated multiprocessor from the MC68302 family that combines a M68000-compatible 32-bit CPU core with an on-chip RISC-based Communications Processor (CP), DMA controller, and a rich set of serial/parallel peripherals, housed in a 132-pin PQFP package measuring 46 x 46 mm. It targets networking, telecom, and embedded communications applications that benefit from hardware-assisted protocol handling alongside a general-purpose 32-bit instruction set. Background: A microprocessor (MPU) is the central processing unit of an embedded system, executing instruction code, managing memory, and arbitrating peripheral access. The MC68302EH25C belongs to the M68000 (68K) family of CISC processors, which historically dominated telecommunications and industrial control. The "EH" suffix designates the Enhanced Hardware variant, and "25C" denotes a 25 MHz clock with the ceramic-windowed / commercial (C) temperature designation. This part is a system-on-chip predecessor of the ColdFire family, integrating CPU + DMA + serial + timers into one die. Key features include a 32-bit M68000 instruction set architecture with 8/16-bit external data bus, a RISC Communications Processor for HDLC/SDLC/UART/Transparent bit-stream handling, three independent full-duplex serial communications controllers (SCC), two serial management controllers (SMC), a 2-channel DMA controller, three timers, 1152 bytes of dual-port RAM for CP/CPU messaging, and an interrupt controller supporting up to 7 external IRQ lines. The architecture uses a Harvard-style split between the 68000 core and the RISC CP, allowing the CP to handle real-time bit-stream processing autonomously while the 68000 core runs system software. The 8/16-bit dynamic bus interface supports DRAM refresh and glueless memory interfacing, reducing external logic in cost-sensitive designs. Typical applications include ISDN terminal adapters, X.25 / frame relay packet assemblers, industrial control networks, serial-port multiplexers, and proprietary field-bus bridges. The integrated CP offloads HDLC framing so the 68000 core can manage higher-layer protocols without real-time jitter. When designing with this device, allocate at least 4.5 us between DMA bursts to avoid starving the SCC FIFOs. Note that this part is NXP End-of-Life; long-term designs should consider the pin-compatible MC68302FC variant or migrate to ColdFire MCF523x. This page synthesizes distributor stock, NXP end-of-life notices, drop-in alternative guidance, and engineering design notes not found in the original manufacturer datasheet.

RFC Hubungi kami
MC68302RC16C - 16MHz M68000 IMP | NXP Semiconductors
MC68302RC16C

MC68302RC16C - 16MHz M68000 IMP | NXP Semiconductors

The NXP Semiconductors MC68302RC16C is a 16 MHz Integrated Multiprotocol Processor (IMP) based on the M68000 family core with 1 core operating at 8/16-bit data width, housed in a 132-pin PGA (34.5 x 34.5 mm) package. It belongs to the M683xx microprocessor product family and operates from a 5 V supply, integrating a closely coupled industry-standard MC68000/MC68008 CPU core with a flexible communications architecture aimed at networking and communications controllers. What is an Integrated Multiprotocol Processor (IMP)? An IMP is a highly integrated single-chip solution that combines a general-purpose microprocessor with dedicated serial-communications peripherals (such as HDLC/SDLC controllers, UARTs, and timers) plus DMA channels, all on the same silicon die. Within the broader component taxonomy the MC68302 sits between a microcontroller (MCU) and an applications processor, with a product hierarchy of M68000 core -> microprocessor (MPU) -> standard microprocessor -> discrete digital IC -> semiconductor. The IMP concept reduces board area, BOM cost and software complexity when implementing multi-channel communication endpoints. Key features include the M68000 CPU core running at 16 MHz, three serial communications controllers (SCCs) supporting HDLC/SDLC/UART/Transparent modes, two serial management controllers (SMCs), two peripheral/timer modules, up to four DMA channels, and up to 2 Kbytes of dual-ported system RAM. The device supports a 16-bit data bus and a 24-bit address bus, four external chip-select outputs with programmable wait-state generation, and a 5 V single supply. Software compatibility with the broader MC68000 family allows reuse of existing toolchains, compilers, and OS ports. Architecturally, the MC68302 combines the proven 68000 instruction set with RISC-style on-chip peripheral engines connected via an internal bus, allowing the CPU to offload bit-rate-oriented protocol work to dedicated hardware. This architecture delivers deterministic throughput on multiple HDLC channels while leaving CPU cycles available for the upper-layer protocol stack and management plane. Typical applications include multi-channel WAN routers and bridges, ISDN terminal adapters, telecom line cards, industrial serial concentrators, and legacy networking equipment. The combination of an industry-standard CPU and on-chip communications peripherals also makes the part attractive for protocol-conversion gateways and embedded control planes where deterministic I/O is required. When designing with this device, allocate the 132-pin PGA footprint on a through-hole or pin-grid-array compatible PCB, provide a 5 V supply with adequate decoupling near the supply pins, and use a Motorola-compatible toolchain (such as a 68K compiler and a BDM or background-debug interface) for firmware bring-up. Note that this part contains lead and is RoHS non-compliant; it is now considered a legacy/extended-life component with new designs expected to migrate to RoHS-compliant successors. This page synthesizes distributor pricing, the pin-equivalent same-family alternatives, and practical design notes not found in the original manufacturer datasheet.

RFC Hubungi kami
MC68302RC20C - M68302 20MHz Integrated Multiprotocol Processor | NXP
MC68302RC20C

MC68302RC20C - M68302 20MHz Integrated Multiprotocol Processor | NXP

The NXP MC68302RC20C is a 20 MHz integrated multi-channel communications processor that combines an MC68000/MC68008 microprocessor core with a flexible communications architecture on a single chip, housed in a 132-pin ceramic PGA (Pin Grid Array) package measuring 34.5 x 34.5 mm. The MC68302 was the first device to offer the benefits of a closely coupled, industry-standard M68000 core with on-chip DMA, serial communications channels, and parallel I/O, making it a versatile building block for networking and communications products. An integrated multiprotocol processor (IMP) is a system-on-chip device that merges a general-purpose CPU with peripheral communication controllers, reducing the bill of materials for routers, bridges, and embedded communication nodes compared with discrete CPU-plus-ASIC designs. Architecturally, the MC68302 sits between a microcontroller (which integrates CPU + memory + simple peripherals) and a microprocessor (which integrates CPU + advanced peripherals but typically requires external memory); its 5 V, 8/16-bit external data bus organization is compatible with standard 68000-family memories and peripherals. Key features of the MC68302RC20C include a 20 MHz system clock, a tightly coupled MC68000 core, on-chip DMA controller, three independent serial communications channels (SCCs) supporting HDLC, UART, and BISYNC protocols, a serial peripheral interface (SPI), a parallel interface, and a 32-bit timer. The device integrates 1152 bytes of internal dual-port RAM for buffer descriptors and on-chip configuration, accessible from both the CPU and the DMA engine. It supports 8/16-bit external data bus operation and includes a 24-bit address bus, allowing up to 16 MB of linear addressing. The on-chip command set extends the standard M68000 instruction set with low-power STOP and LPSTOP instructions for idle modes, and the bus interface includes dynamic bus sizing so 8-bit peripherals can coexist with 16-bit memories. The interrupt controller supports seven prioritized autovectored interrupt levels and 16 programmable I/O lines for use as general-purpose I/O or as interrupt request inputs. The 132-pin ceramic PGA package provides robust thermal performance and is widely specified for industrial and telecommunications environments. Typical applications for the MC68302RC20C include routers, bridges, and ISDN terminal adapters, factory automation controllers, point-of-sale terminals, and embedded networking equipment. Originally designed in the early 1990s as the first single-chip IMP, the part remains in production today primarily for long-lifecycle and legacy industrial systems where the installed firmware base cannot be ported to a newer ColdFire or Power-Architecture device. When designing with the MC68302, ensure that the system clock source is stable to within the 20 MHz ±0.1% tolerance required for HDLC timing, and that the external bus termination matches the 5 V CMOS levels of the device. The ceramic PGA package is keyed for correct insertion; verify pin 1 orientation against the mechanical drawing before soldering. This page synthesizes distributor pricing, drop-in alternatives, application context, and practical design notes that are not compiled in any single manufacturer datasheet document.

RFC Hubungi kami
MC68306AG16B - 16MHz Integrated EC000 MPU | NXP | 144-LQFP
MC68306AG16B

MC68306AG16B - 16MHz Integrated EC000 MPU | NXP | 144-LQFP

The NXP MC68306AG16B is an integrated 32-bit microprocessor from the M683xx family that combines a 68EC000 CPU core with system-level peripherals in a single 144-pin LQFP (20x20) package. It operates at 16 MHz over a 5V supply, providing 68000-class performance with integrated glue logic that reduces external component count for embedded control designs. A microprocessor (MPU) is the central processing unit of an embedded computing system, typically paired with external memory and peripherals via an external bus. The 68000/68EC000 family sits in the hierarchy of 32-bit CISC microprocessors -> M68000 family -> Motorola/Freescale/NXP M683xx integrated processors -> embedded industrial control. The MC68306 specifically integrates the 68EC000 core with common system peripherals, eliminating the need for external bus arbitration, interrupt controllers, and chip-select logic that discrete 68000 designs require. Key features include 16 MHz CPU clock, 32-bit internal data path with 16-bit external data bus (EC000 core), 24-bit address bus, integrated peripherals (timers, serial, parallel I/O, interrupt controller, chip-select logic), and a wide 5V operating supply. The 144-LQFP package provides ample I/O for the integrated peripheral set while remaining hand-solderable for prototypes. Architecturally, the MC68306 separates the CPU core from the peripheral bus, allowing peripheral operations to occur in parallel with CPU execution. The 68EC000 core uses a simplified 16-bit external data path versus the full MC68000's 32-bit path, reducing bus complexity while preserving the 32-bit internal register set. Typical applications include industrial process control, point-of-sale terminals, medical instrumentation, building automation controllers, automotive body electronics, and legacy equipment maintenance. The integrated peripherals make it suitable for designs where board space, BOM count, and reliability are priorities. When designing, ensure the 5V supply rail is clean and decoupled with 0.1uF and 10uF capacitors near each power pin. The EC000's 16-bit external bus requires careful PCB trace length matching (within 1 inch) for memory accesses above 8 MHz to prevent bus errors. This page synthesizes distributor pricing, drop-in alternatives, lifecycle status, and practical design notes from the NXP product brief, complementing the official datasheet with actionable engineering context.

RFC Hubungi kami
MC68306CEH16B - 16MHz 32-Bit Integrated EC000 MPU | NXP
MC68306CEH16B

MC68306CEH16B - 16MHz 32-Bit Integrated EC000 MPU | NXP

The NXP MC68306CEH16B is an integrated 32-bit microprocessor based on the MC68EC000 core, delivered in a 132-pin bumpered PQFP package at 16 MHz. It combines an EC000 processor core, system integration logic, DRAM controller, serial channel, timers, and chip-select logic in one device, replacing multiple discrete 68000-family glue chips with a single IC. Background: An MPU (microprocessor unit) is the central processing element of an embedded system. The 68000/EC000 family is a CISC 32-bit architecture with a 16-bit external data bus, widely used in industrial control, automotive body electronics, telecommunications, and legacy embedded designs. The MC68306 specifically targets systems that need 68000-class CPU performance plus built-in peripherals (DRAM controller, UART, timers, parallel I/O, interrupt controller, chip-select logic), enabling engineers to build compact MPU-based boards with minimal external logic. Within the broader taxonomy: MPU -> microprocessor -> processor -> digital IC -> semiconductor. Key features: 16 MHz clock, 32-bit internal architecture with 16-bit external data bus, integrated DRAM controller with refresh, two DMA channels, dual serial channels (UART), 16-bit timer, 8-bit parallel I/O port, eight chip-select outputs, interrupt controller, and 5 V I/O. The 132-pin bumpered PQFP (24.13 mm x 24.13 mm) provides robust lead compliance and reliable solder joints through thermal cycling - important for industrial and automotive-grade assemblies. The MC68306EC000 core executes the M68000 instruction set, supports seven address modes and 14 data types, and includes a hardware multiply/divide unit. To deliver M68000-class performance, the device integrates common system peripherals so designers spend less time building glue logic and more time on application code. The 16 MHz version (CEH16B suffix) targets applications where the 8 MHz or 10 MHz variants are too slow but full 25 MHz operation is unnecessary, balancing cost and performance for typical control loops and protocol stacks. Typical applications include industrial process controllers, building automation controllers, point-of-sale terminals, automotive body controllers, legacy communications equipment, printer controllers, and embedded control boards requiring 68000 software compatibility. Designers often select it for long-life-cycle products where re-validation costs are prohibitive and the mature toolchain (GNU m68k-elf, Diab, GCC) and RTOS support (OSEK, RTEMS, SMX) are well established. When designing with this part, ensure the 5 V supply is well-decoupled with 100 nF ceramic caps near each VCC pin and a bulk 10 uF tantalum or aluminum-polymer cap. The 16 MHz bus requires careful PCB layout: keep traces short, maintain a continuous ground plane under the PQFP, and route the clock signal first. Also plan for the MC68306's address bus to drive memory directly - bus loading analysis is recommended when adding external peripherals. This page synthesizes distributor pricing, drop-in NXP alternatives, comparison with the MC68332 and MC68HC16Z1, and practical design notes not found in the manufacturer datasheet - giving engineers a single source for procurement, selection, and PCB implementation guidance.

RFC Hubungi kami
MC68306EH16BR2 - 16MHz EC000 MPU, 132-PQFP | NXP/Freescale
MC68306EH16BR2

MC68306EH16BR2 - 16MHz EC000 MPU, 132-PQFP | NXP/Freescale

The NXP (formerly Freescale) MC68306EH16BR2 is a 32-bit integrated EC000 microprocessor (MPU) from the M683xx Coldfire/M68K family, operating at 16 MHz and housed in a 132-pin Plastic Quad Flat Pack (PQFP) package measuring 24.13 mm x 24.13 mm. It integrates a 32-bit EC000 core with on-chip peripherals and DRAM controller, providing a single-chip embedded processing solution for industrial control, telecom, and legacy M68K designs. The device is currently listed as Obsolete per distributor stock pages, with remaining inventory available through authorized distributors and aftermarket suppliers. An MPU (Microprocessor Unit) is a CPU-centric integrated circuit that requires external memory and peripherals to form a complete system. The M68K family traces its lineage to the Motorola 68000 architecture introduced in 1979, which pioneered a flat 32-bit programming model and orthogonal instruction set. The MC68306 specifically integrates the EC000 core with system glue logic - DRAM controller, chip-select logic, timers, and serial ports - to reduce total BOM in cost-sensitive embedded designs. Within the broader taxonomy, the MC68306 sits under microprocessor -> MPU -> 32-bit processor -> embedded processor -> integrated circuit. Key features include a 16 MHz maximum clock frequency, 5.0 V I/O voltage, single 32-bit core, and integrated DRAM controller. The PQFP-132 package supports surface-mount assembly on legacy through-hole-friendly footprints and remains compatible with the original 68306 reference designs. The architecture retains M68K instruction compatibility, allowing code developed for earlier 68000/68306 designs to migrate without software rewrites. The part supports up to 4 GB of address space through 32-bit linear addressing. Typical applications include industrial automation controllers, telecommunications infrastructure, point-of-sale terminals, legacy M68K embedded systems, and factory automation equipment. The integrated DRAM controller and chip-select logic reduce external component count compared to discrete CPU implementations. Designers continue to specify the MC68306EH16BR2 for maintenance of installed bases and for long-life-cycle industrial systems where requalification costs discourage migration to newer architectures. When designing with this device, note that the part is Obsolete per current distributor listings (as of 2026-10-16); consider NXP's recommended migration path to ColdFire MCF5208 or similar modern M68K-compatible devices for new designs. PCB layout must accommodate the 132-pin PQFP footprint with adequate thermal relief. Decoupling capacitors should be placed close to the multiple VCC/GND pairs. This page synthesizes distributor pricing, lifecycle status, and migration options not found in the original manufacturer datasheet.

RFC Hubungi kami
MC68322FT20 - 16-Bit 20 MHz M683XX Processor | Motorola
MC68322FT20

MC68322FT20 - 16-Bit 20 MHz M683XX Processor | Motorola

The Motorola MC68322FT20 is a 16-bit microprocessor built around the M683XX embedded-processor family, operating at up to 20 MHz with one core in a 160-lead QFP package measuring 28 mm by 28 mm. Its primary characteristics are a 16-bit processor architecture, 20 MHz operating frequency, single-core implementation, and the 160-QFP (28 x 28 mm) package identified for the exact MC68322FT20 ordering code. A microprocessor IC is the central processing component of an embedded system. Unlike a general-purpose desktop CPU, this device targets embedded control, communications, industrial, and legacy equipment designs where deterministic software execution and a stable peripheral interface are more important than processor scaling. In the product hierarchy, MC68322FT20 is a microprocessor IC, an embedded processor, and a member of the M683XX family. The “F” package designator and “T20” ordering suffix distinguish this exact 20 MHz, 160-QFP configuration from other MC68322 variants. The principal feature set established for MC68322FT20 includes one 16-bit processing core, a maximum clock frequency of 20 MHz, and a 160-QFP (28 x 28 mm) surface-mount package. These figures place the component in the legacy embedded-control class, where the processor operates as the system controller rather than as a host processor. Its 160 leads provide substantially more interface and power connectivity than a modern low-pin-count microcontroller, which is important when maintaining a complex legacy motherboard layout. MC68322FT20 belongs to the Motorola M683XX architecture and carries the EC000 classification in the distributor listing. Its 16-bit architecture and 20 MHz clock are consistent with systems designed around M683XX software, peripheral mappings, and established board-level interconnects. Design migration must account for the complete legacy hardware environment rather than treating processor speed as the only compatibility criterion. Memory organization, bus timing, peripheral functions, reset behavior, and electrical characteristics must be confirmed against the manufacturer documentation before any redesign. Typical uses include industrial controllers, communications equipment, embedded instrumentation, and service systems built around the M68322 processor. In these applications, the 20 MHz clock provides the execution rate, the 16-bit instruction and data environment supports the original control software, and the 160-QFP footprint preserves compatibility with densely routed legacy boards. Replacement or modernization should normally begin with a complete system audit because a package match alone does not establish software, clock, memory, and peripheral compatibility. The primary PCB-design consideration is that MC68322FT20 requires the exact 160-QFP land pattern, correct pin assignment, and layout rules associated with the 28 x 28 mm package. Existing boards should not be treated as generic QFP replacements. Confirm every power pin, ground connection, clock source, reset path, and peripheral signal against the manufacturer pin-description table before assembly or board rework. This product page combines the exact orderable MPN, processor classification, clock rating, package information, sourcing guidance, and engineering-oriented comparison guidance. It also highlights the practical distinction between an exact legacy replacement and a merely similar embedded processor, helping teams protect board compatibility, software continuity, and long-term serviceability.

RFC Hubungi kami
MC68331CAG25 - 32-bit M68300 MCU 25MHz | NXP LQFP-144
MC68331CAG25

MC68331CAG25 - 32-bit M68300 MCU 25MHz | NXP LQFP-144

The NXP Semiconductors MC68331CAG25 is a highly-integrated 32-bit microcontroller from the M68300 ColdFire/CPU32 family, operating at 25 MHz and housed in a 144-pin LQFP package measuring 20x20 mm. A 32-bit microcontroller is a microprocessor core with on-chip peripherals, memory interfaces, and I/O designed for embedded control. The MC68331 builds its system from standardized functional modules - the CPU32 processor core, a System Integration Module (SIM), a General Purpose Timer (GPT), and a Queued Serial Module (QSM) - that interconnect through a common Intermodule Bus (IMB). This modular taxonomy places the device in the larger hierarchy of CPU -> MPU -> microcontroller -> embedded processor -> semiconductor. Key features include 25 MHz CPU32 core performance, ROMless architecture for flexible external program memory, 18 programmable I/O lines, internal oscillator support, and a 144-pin LQFP (20x20 mm) footprint. The SIM integrates chip-select logic, interrupt control, and bus arbitration; the GPT supplies configurable timers for event capture and waveform generation; the QSM provides queued SPI and SCI/UART channels for asynchronous and synchronous serial communications. The CPU32 core uses a 32-bit Von Neumann architecture with a 32-bit data path and 32-bit address bus. The ROMless variant routes external program fetch through the SIM's chip-select and wait-state logic, enabling large code and data spaces. The modular IMB topology makes peripheral expansion and configuration relatively simple compared with single-block designs. Typical applications include automotive body and chassis controllers, industrial automation and motor drives, robotics, process control, factory automation, and embedded communications gateways where deterministic 32-bit performance and flexible memory mapping are required. When designing with this part, prioritize decoupling and IMB signal integrity: place 0.1 uF ceramic capacitors near each VDD/VSS pair, route the IMB clock with controlled impedance, and verify chip-select timing with worst-case wait-state scenarios. Note that this MPN is marked End of Life on the NXP product page; plan for obsolescence accordingly. This page consolidates distributor pricing, drop-in M68300 alternatives, and design considerations not assembled in the manufacturer datasheet alone.

RFC Hubungi kami
MC68331CEH25 - 25MHz CPU32 M68300 Microcontroller PQFP-132 | NXP
MC68331CEH25

MC68331CEH25 - 25MHz CPU32 M68300 Microcontroller PQFP-132 | NXP

The NXP (formerly Freescale/Motorola) MC68331CEH25 is a 32-bit modular microcontroller built around the CPU32 core running at 25 MHz, packaged in a 132-pin PQFP (24.13 mm x 24.13 mm) and supplied as a ROMless device for external program memory. It integrates a System Integration Module (SIM), a General-Purpose Timer (GPT) and a Queued Serial Module (QSM) on a common intermodule bus (IMB), and is a member of the M68300 modular microcontroller family. According to the NXP product page, the part is announced as End of Life, so engineers should plan replacement now rather than treating the listing as a long-term supply line. A 32-bit microcontroller is an embedded processing IC whose datapath, registers and ALU are 32 bits wide, enabling single-instruction operations on wide data words and larger linear address spaces than 8- or 16-bit parts. The M68300 family belongs to the ColdFire/M68K lineage (CPU32 -> M68k -> ColdFire -> embedded 32-bit MCU) of CISC RISC-style CISC cores, and within NXP's portfolio it sits below the ColdFire MCF5xxx line. The MC68331CEH25 uses the standard M68300 modular IP blocks, which simplifies migration within the family. Key features include 25 MHz CPU32 core performance, ROMless operation for flexible external memory interfacing, the GPT timer block (with capture, compare and pulse-width modulation functions), the QSM providing queued SCI and SPI channels, and the SIM block that handles chip-select generation, system protection, clock synthesis and interrupt prioritization. The 132-pin PQFP footprint gives access to the full external bus plus all on-module peripheral pins. Typical applications include industrial control systems, automotive body and chassis electronics (pre-CAN-era platforms), factory automation, motor control via the GPT PWM outputs, and embedded communication gateways that leverage the QSM serial channels. The 132-pin PQFP package and ROMless architecture make the part attractive where high-performance 32-bit processing is needed alongside custom boot/storage strategies. When designing with this device, ensure the external bus and chip-select signals are properly terminated, the 25 MHz system clock is stable, and the Vcc rails meet the M68300 family DC specifications referenced in the datasheet. Because the part is in NXP's End-of-Life program, source any qualification stock carefully and review the discontinuance notice for the official last-time-buy window and recommended migration target.

RFC Hubungi kami