Mikropengawal

Produk (20,000+)

COP8SAC720M8/NOPB - 8-bit 10MHz 4KB OTP MCU | Texas Instruments
COP8SAC720M8/NOPB

COP8SAC720M8/NOPB - 8-bit 10MHz 4KB OTP MCU | Texas Instruments

The Texas Instruments COP8SAC720M8/NOPB is an 8-bit CMOS microcontroller from the COP8 family (8SA sub-series) featuring 4KB of One-Time Programmable (OTP) program memory, 128 bytes of RAM, and 16 digital I/O lines, housed in a 20-pin SOIC (0.295" / 7.50mm width) package. It runs at 10MHz from a single 3.3V or 5V supply, integrates power-on reset (POR), and provides a very small form factor for space-constrained applications. The /NOPB suffix designates a lead-free, RoHS-compliant shipping version. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (ROM/Flash/OTP), data memory (RAM), and programmable I/O peripherals on one IC. OTP microcontrollers ship blank and are programmed once by the OEM or via a programming socket before deployment - ideal for low-cost, medium-volume production where mask-ROM NRE charges are not justified. The COP8 core uses a CISC instruction set optimized for byte-level bit manipulation, common in white-goods and appliance control. Key features of the COP8SAC720M8/NOPB include 4KB (4K x 8) OTP program memory, 128 x 8 RAM, an integrated power-on reset circuit that holds the CPU in reset until VDD stabilizes, 16 general-purpose I/O pins multiplexed with peripheral functions, a programmable watchdog timer, and an 8-bit timer/counter. The 10MHz clock supports instruction-cycle execution in the 200ns range, sufficient for slow loop-control and user-interface scanning tasks. Typical applications for the COP8SAC720M8/NOPB include white-goods controllers (washing machines, dishwashers, microwave ovens), HVAC thermostats, low-end remote controls, simple sensor read-out boards, and replacement of discrete 8-bit logic in legacy product lines. Its 20-SOIC footprint and wide operating voltage range make retrofit into existing COP8-based designs straightforward. When designing with this part, note that OTP programming requires a special programmer or gang programmer prior to solder; firmware cannot be updated in the field. The part is RoHS-compliant (lead-free /NOPB suffix) per the addressable manufacturing data. Programming model and peripheral registers follow the COP8 architecture reference - consult the manufacturer datasheet for the full register map, interrupt vector table, and timing diagrams before prototyping.

RFC Hubungi kami
COP8SAC720M8X/NOPB - 8-Bit 10MHz 4KB OTP MCU | Texas Instruments
COP8SAC720M8X/NOPB

COP8SAC720M8X/NOPB - 8-Bit 10MHz 4KB OTP MCU | Texas Instruments

The Texas Instruments COP8SAC720M8X/NOPB is an 8-bit CMOS ROM-based and One-Time Programmable (OTP) microcontroller from the COP8™ 8SA family, delivering 10 MHz CPU performance with 4 KB of program memory and 128 bytes of RAM in a 20-pin SOIC package. Per the manufacturer datasheet, this device integrates power-on reset, low-EMI oscillator design, and very small packaging, making it suited for cost-sensitive embedded applications requiring reliable one-time-programmable code storage. The COP8 (Controller Oriented Processor) family is a mature 8-bit CISC architecture originated by National Semiconductor and now maintained by Texas Instruments. COP8 microcontrollers are accumulator-based Harvard-architecture devices featuring a rich instruction set, multiple addressing modes, and integrated peripherals such as timers, A/D converters, and serial interfaces. They are widely deployed in white-goods, appliance, industrial-control, and consumer-electronics applications where deterministic behavior, low EMI, and OTP-based code security are valued. The COP8SAC720M8X/NOPB is the OTP variant of the COP8SA family, intended for prototyping and low-to-medium volume production. Key features include 16 GPIO pins, an 8-bit accumulator-based CPU core, on-chip power-on reset eliminating external reset circuitry, and a wide operating voltage range of 2.7 V to 5.5 V. The 20-SOIC package measures 7.50 mm in body width, and the device operates over the industrial -40 °C to +85 °C temperature range. The integrated oscillator with low-EMI feature reduces electromagnetic emissions in noise-sensitive applications. The COP8SAC720M8X/NOPB is pin-compatible with other COP8SA family members including COP8SAB720M8 and COP8SAC744M8, enabling designers to migrate between memory sizes without PCB rework. It supports in-system programming via TI's development toolchain and is supported by the COP8-ICE emulator. According to the manufacturer datasheet, the device includes a multi-source interrupt controller, two 16-bit timers, and a UART-compatible serial port. Typical applications include appliance control boards, HVAC thermostat controllers, security alarm panels, battery charger control, and small home-automation sensor nodes. The OTP memory provides one-time programmability for low-volume or secure code storage, eliminating the need for external EEPROM in many designs. When designing with this part, ensure the OTP programming voltage and timing requirements are observed during code development. The COP8 instruction set is non-standard, so engineers must use the TI COP8 assembler and toolchain for code development.

RFC Hubungi kami
CP80C88-2Z - 80C88 8MHz CMOS CPU 40-PDIP | Renesas/Intersil
CP80C88-2Z

CP80C88-2Z - 80C88 8MHz CMOS CPU 40-PDIP | Renesas/Intersil

The Renesas/Intersil CP80C88-2Z is an 8/16-bit CMOS microprocessor (CPU) from the 80C88 family operating at 8 MHz from a single 5 V supply, housed in a 40-pin PDIP (0.600 in / 15.24 mm) through-hole package. It is a drop-in CMOS successor to the NMOS 8088, executing the same x86 real-mode instruction set while dramatically reducing power consumption. A microprocessor (MPU) is the central processing unit of a computer system: it fetches instructions from memory, decodes them, and executes arithmetic, logic, and I/O operations. The 80C88 sits within the x86 processor hierarchy (8086 -> 8088 -> 80C88 -> 80186/80286), making it software-compatible with the vast ecosystem of 8086/8088 code, BIOS implementations, and peripherals such as the 8284 clock generator and 8288 bus controller. Key features of the CP80C88-2Z include an 8 MHz maximum clock frequency, a multiplexed 8-bit external data bus with a 16-bit internal architecture, a 20-bit address bus addressing up to 1 MB of memory, and two operating modes: MINimum mode for small single-processor systems and MAXimum mode for larger multiprocessor applications. CMOS fabrication (self-aligned silicon gate, scaled SAJI IV process) gives it far lower static and dynamic power draw than the original NMOS 8088. Technically, the device uses a prefetch queue and bus interface unit separated from the execution unit, allowing instruction fetch and execution to overlap. The 2 suffix denotes the 8 MHz speed grade, and the Z suffix denotes lead-free, RoHS-compliant construction. Compatible support chips (8284A, 8288, 8259A, 8237A) allow a full board-level system design. Typical applications include legacy industrial control systems, embedded x86 single-board computers, avionics and test-equipment maintenance, and educational/retro-computing platforms that require authentic 8088 bus timing. Design consideration: use the 8284A clock generator for a properly phased CLK signal, and ensure READY-based wait states for slow EPROM/EEPROM memories; do not exceed the 5 V +/-10% supply range. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not consolidated in the manufacturer datasheet.

RFC Hubungi kami
CS80C86 - 16-Bit 5 MHz CMOS Microprocessor | Harris
CS80C86

CS80C86 - 16-Bit 5 MHz CMOS Microprocessor | Harris

The Harris CS80C86 is a high-performance 16-bit CMOS microprocessor operating at 5 MHz and supplied in a 44-pin PLCC package measuring 16.58 mm by 16.58 mm. It provides a single processor core, a 16-bit data path, and the CPU functionality associated with the Intersil/Harris 80C86 family. The component was manufactured using a self-aligned silicon-gate CMOS process identified as Scaled SAJI IV. Its listed distributor price begins at $2.9070 as of 2026-10-23, and one LCSC listing reports in-stock inventory. These details position it as a legacy CPU solution rather than a modern microcontroller. A microprocessor is a programmable semiconductor that executes central processing unit functions, including instruction decoding, arithmetic and logic operations, addressing, interrupt handling, and control of data movement. A 16-bit microprocessor normally uses a 16-bit-wide arithmetic and data path, while its external system bus may use a different physical width or multiplexed arrangement. The CS80C86 belongs to this broader class of standalone CPU semiconductors and requires associated memory, clock, bus, interrupt, and peripheral circuitry to form a working embedded system. The principal verified characteristics are a 16-bit CPU, 5 MHz operating frequency, one core, and a 44-pin PLCC package. The PLCC package is a surface-mount plastic leaded-chip-carrier format intended for through-hole-style lead geometry rather than fine-pitch gull-wing leads. Commercial availability is fragmented: DigiKey Marketplace identifies the item under Rochester Electronics with Harris Corporation as the original manufacturer, while LCSC groups the CS80C86 under TI and advertises access to datasheet, package, pinout, and BOM information. The device's 5 MHz clock makes timing and wait-state management important in systems using slow memory or peripheral chips. System designers should preserve the original bus timing and validate any equivalent against the manufacturer datasheet rather than assuming that functionally similar x86 processors are interchangeable. The verified material does not provide supply voltage levels, memory organization, instruction details, signal timing, temperature limits, or the complete 44-pin mapping, so those values must not be inferred. Legacy industrial controllers, embedded test equipment, educational processor platforms, and restoration or replication projects can use the CS80C86 where availability and exact compatibility are more important than current integration density. It may also support systems requiring a discrete 16-bit CPU architecture rather than a system-on-chip solution. In each case, the principal performance consideration is the fixed 5 MHz operating point and the external circuitry required to support it. Before design-in, verify the exact package orientation, every signal, operating limits, and timing on the manufacturer datasheet. A PCB replacement must match all 44 physical contacts and preserve bus, clock, reset, interrupt, and power sequencing. Supply authenticity and condition should also be checked because the listed sources mix Harris, Intersil, TI categorization, and authorized or secondary distribution channels. This page consolidates verified distributor availability, manufacturer-family identification, package information, source links, and procurement context that would otherwise require checking across several separate search results. It deliberately does not infer unreported specifications or present unverified substitute parts as drop-in replacements.

RFC Hubungi kami
CS80C88 - 5 MHz CMOS 8/16-Bit Microprocessor | Intersil
CS80C88

CS80C88 - 5 MHz CMOS 8/16-Bit Microprocessor | Intersil

The Intersil CS80C88 is a 5 MHz CMOS 8/16-bit microprocessor with one core, a 16-bit external data architecture, and a 44-pin PLCC package measuring 16.58 mm by 16.58 mm. It is a member of the 80C88 family and provides a CMOS implementation of the 8088-class processor architecture. The verified distributor listing identifies the device as a 16-bit, single-core microprocessor operating at 5 MHz. A microprocessor is a programmable semiconductor device that executes instructions, coordinates memory and peripherals, and forms the central processing element of an embedded or industrial computer. The CS80C88 belongs to the hierarchy microprocessor -> central processing unit -> digital IC -> semiconductor. Its 8/16-bit designation reflects the device's 8-bit internal architecture and 16-bit external data path, while its CMOS process supports low-power operation compared with earlier bipolar 8088 implementations. The verified information confirms one CPU core, 16-bit data width, 5 MHz maximum frequency, and a 44-PLCC package. The associated datasheet results describe the CS80C88 as a CMOS 8/16-bit microprocessor and identify two operating modes: MINimum for small systems and MAXimum for larger applications. Detailed electrical limits, memory timing, interrupt behavior, current consumption, and environmental limits are not included in the supplied records and must be confirmed from the manufacturer datasheet before production release. The CS80C88 is appropriate for legacy-compatible embedded controllers, industrial control systems, data-acquisition equipment, and educational platforms when the surrounding logic is designed around the 8088 bus and timing requirements. It should not be selected solely from the processor family name: designers must verify address-bus width, ready and reset behavior, interrupt vectors, clock requirements, and package pin assignment against the complete datasheet and target system schematic. The main design consideration is legacy-bus integration. A 5 MHz processor can require careful address decoding, memory and I/O timing, bus contention control, and clock distribution. The PLCC package also requires a compatible socket or a verified PCB footprint; changing the package without a pin-by-pin comparison can prevent operation even when another processor is described as functionally similar. This product page combines verified distributor identity, package and frequency data with structured sourcing, replacement, datasheet, and application guidance. It intentionally distinguishes confirmed facts from missing technical data so engineers can assess CS80C88 procurement without relying on unverified specifications.

RFC Hubungi kami
CY7C65113A-SXC - 4-Port USB Hub Controller | Infineon
CY7C65113A-SXC

CY7C65113A-SXC - 4-Port USB Hub Controller | Infineon

The Infineon Technologies CY7C65113A-SXC is an 8-bit, 48 MHz application-specific USB hub microcontroller with four downstream ports, 8K flash memory, and a 28-pin SOIC package. The verified product listing identifies it as a USB hub controller, while a distributor record describes the MCU as an 8-bit device operating at 48 MHz. Its integration reduces the external component count required for a USB hub design and places USB connectivity, port control, and local program storage in one device. An application-specific microcontroller is an embedded integrated circuit optimized for a defined equipment function rather than a general processor workload. Within the semiconductor hierarchy, this device belongs to the microcontroller family and specifically serves as a USB hub controller. Its 48 MHz processing capability supports USB traffic handling and hub-management logic, while the four-port configuration targets hubs that fan one upstream USB connection to multiple downstream devices. The verified listing identifies a 28-SOIC package and tube packaging. The package provides a surface-mount implementation compatible with conventional PCB assembly, and the SOIC form factor supports automated manufacturing while exposing more component leads than compact packages. The recorded 8K memory figure describes the device's on-chip program storage context, while the exact memory organization and programming interface require confirmation from the manufacturer datasheet. Typical uses include USB hubs, desktop peripherals, computer accessories, and embedded USB expansion equipment. In a hub design, the controller connects an upstream USB port to four downstream ports and manages downstream attach, detach, reset, and enumeration behavior under firmware control. The application-specific architecture can simplify board design compared with a discrete hub controller plus separate microcontroller arrangement, provided the design uses the manufacturer's reference firmware and electrical guidance. Engineers should verify the complete pinout, USB electrical limits, clock requirements, power sequencing, and firmware compatibility before layout because those details are not present in the supplied search data. A replacement must use the same 28-SOIC footprint and preserve pin functions, firmware behavior, voltage levels, timing, and USB compliance; a matching package name alone does not establish drop-in compatibility. This page consolidates verified sourcing information, package data, application context, and replacement-selection guidance rather than inferring unprovided electrical specifications.

RFC Hubungi kami
CY7C65113C-SXC 48MHz USB Hub MCU | Infineon
CY7C65113C-SXC

CY7C65113C-SXC 48MHz USB Hub MCU | Infineon

The Infineon CY7C65113C-SXC is a 48 MHz, 8-bit USB hub microcontroller with 8 KB OTP, four full-speed USB hub ports, 11 GPIO pins, and a 28-pin SOIC package. Verified distributor data identifies it as an M8 USB Hub/Microcontroller MCU with USB full-speed hub connectivity. Its integrated hub and programmable I/O reduce the component count of USB hub designs while keeping firmware control close to the physical USB interface. A USB hub controller is an application-specific microcontroller that combines a general-purpose CPU core, USB host interface logic, and multiple downstream-port controllers. Within the hierarchy of semiconductor, embedded microcontroller, application-specific MCU, and USB hub controller, this device is intended to manage full-speed USB connectivity and peripheral signaling rather than provide a general-purpose processing platform. Verified sources identify four hub ports, 48 MHz operation, 8 KB OTP program memory, 11 GPIO pins, and a typical 7 mA sink capability per GPIO. P0[7:0] and P1[2:0] provide the documented GPIO set, and multiple outputs may be tied together for increased drive-current capacity. The SOIC-28 package is identified as 0.295 inch, or 7.50 mm, wide. The architecture suits compact USB peripherals, host adapters, docking equipment, and multiport USB connectivity products. Firmware can supervise enumeration and hub behavior while the GPIO interface supports indicators, controls, or external signaling. Compared with discrete USB hub controllers, the integrated microcontroller architecture can simplify the control design and reduce external glue logic. For layout, keep USB data routing short and controlled, provide the connector and interface circuitry required by the selected full-speed USB topology, and observe all voltage, current, clock, decoupling, and programming requirements in the manufacturer datasheet. Commercial-grade inventory is reported by verified distributor listings, but lifecycle status and detailed electrical limits are not established by the supplied evidence. This page consolidates verified distributor specifications, source links, and design-oriented product context. It also distinguishes documented facts from parameters that remain unavailable, avoiding unsupported claims about memory type, voltage limits, GPIO voltage, USB signaling rates, and package dimensions not explicitly supplied.

RFC Hubungi kami
CY7C65113C-SXCT 12Mbps 4-Port USB Hub | Infineon
CY7C65113C-SXCT

CY7C65113C-SXCT 12Mbps 4-Port USB Hub | Infineon

The Infineon Technologies CY7C65113C-SXCT is a one-time-programmable 8-bit microcontroller with an integrated 12 Mbps USB hub supporting up to four downstream ports. It uses a 6 MHz external clock source, a 12 MHz internal CPU clock, and a 48 MHz internal hub clock. The device is supplied in a 28-pin SOIC package measuring 0.295 inches, or 7.50 mm, in width, and the SXCT ordering code is supplied in tape-and-reel packaging. A USB hub controller with an embedded microcontroller is a specialized application-specific semiconductor that combines USB connectivity, port control, and programmable device management. Within the broader hierarchy, this device belongs to microcontrollers, USB interface integrated circuits, interface ICs, and semiconductors. Its Harvard-architecture instruction set was optimized specifically for USB operations, while retaining applicability to non-USB embedded-control functions. The principal feature is a full-speed USB hub integrated with a one-time-programmable 8-bit CPU. Verified source material identifies 8 KB of OTP program memory, four downstream-port support, 12 Mbps operation, a 6 MHz external clock, a 12 MHz internal CPU clock, and a 48 MHz internal hub clock. These parameters make it appropriate for compact USB hub, peripheral-control, and embedded USB-management designs where one device must perform both hub and local control functions. The device uses a Harvard architecture, separating the program and data organizations to support USB-oriented execution. Its one-time-programmable memory fixes the implemented firmware at production programming time. This characteristic can simplify secure configuration for dedicated USB products, but it also means design changes may require another programmed part rather than a simple field firmware update. Typical uses include four-port full-speed USB hubs, USB peripheral controllers, host-assisted downstream-port management, and compact embedded USB adapters. In a hub design, the downstream ports coordinate device attachment and enumeration, while the integrated microcontroller can manage board-specific functions. External USB transceivers, protection components, connectors, passives, and decoupling networks should be selected according to the system-level USB design requirements. PCB layout should keep USB data routing short, controlled, and away from noisy switching nodes. Follow the manufacturer datasheet for package dimensions, pin assignments, clock connections, decoupling, and programming. The SXCT package is 28-pin SOIC, so its footprint must match a 28-pin gull-wing layout rather than a leadless package. Commercial sourcing data and the manufacturer datasheet should be reviewed before approving a new design. This page consolidates verified distributor specifications, official-datasheet excerpts, package data, application guidance, and replacement-status analysis. Its practical value is that it distinguishes true device options from unsupported cross-reference results and highlights the OTP, clock, USB, and package constraints that most often determine design reuse.

RFC Hubungi kami
CY7C68013A-100AXC USB 2.0 Controller | Infineon
CY7C68013A-100AXC

CY7C68013A-100AXC USB 2.0 Controller | Infineon

The Infineon CY7C68013A-100AXC is a ROMless EZ-USB FX2LP USB 2.0 peripheral controller with a high-speed 480 Mbps USB interface, 16 KB of RAM, 40 GPIOs, and an integrated 8051 microcontroller core, housed in a 100-pin TQFP package. It combines USB connectivity, programmable I/O, serial debugging, and an embedded microcontroller in one device. A USB peripheral controller is an application-specific integrated circuit that manages transactions between a USB host and attached peripherals. The CY7C68013A family belongs to the broader hierarchy of USB interface controllers, embedded microcontrollers, and semiconductor ICs. Its architecture lets designers implement custom USB devices, data-acquisition systems, test equipment, and human-interface devices without using a general-purpose host controller. The headline features include USB 2.0 high-speed operation at 480 Mbps, 16 KB of internal RAM, and 40 GPIOs in a 100-pin TQFP package. The integrated 8051 core provides firmware execution and peripheral control, while serial debug supports development and troubleshooting. The part is intended for non-battery-powered applications, making it suitable for equipment that can remain connected to an external USB power source. Technically, the controller organizes USB endpoint behavior, data transfer, and general-purpose I/O around its embedded processor. Its 16 KB RAM supports endpoint buffering and working memory, while the 40 GPIOs can connect status indicators, control signals, relays, displays, or external interface circuits. Compared with a discrete USB transceiver plus host-side controller arrangement, the integrated FX2LP architecture reduces board complexity and centralizes protocol handling in the same IC. Typical uses include USB data-acquisition equipment, protocol analyzers, logic-analyzer interfaces, test-and-measurement instruments, industrial control adapters, and custom USB peripherals. The 480 Mbps interface is particularly useful when transferring larger blocks of data between a PC and acquisition hardware while retaining dedicated GPIO for synchronization and control. PCB design should preserve short USB differential traces, provide correct impedance-controlled routing, and place supporting components close to their associated pins. Because the device combines a microcontroller and USB peripheral controller, firmware timing and endpoint configuration are as important as electrical layout. Validate suspend, resume, bus-powered, and externally powered operating arrangements during system validation. This product record combines manufacturer-level USB, memory, GPIO, package, and lifecycle information with drop-in replacement analysis and practical integration guidance. It helps engineers evaluate the CY7C68013A-100AXC for new designs and plan transitions where the original FX2LP device is no longer the preferred sourcing choice.

RFC Hubungi kami
CY7C68013A-128AXC 128-Pin USB 2.0 Controller | Infineon
CY7C68013A-128AXC

CY7C68013A-128AXC 128-Pin USB 2.0 Controller | Infineon

The Infineon Technologies CY7C68013A-128AXC is an EZ-USB FX2LP USB 2.0 peripheral controller and ROMless 8051 microcontroller with a 24 MHz clock, 16 KB of RAM, 40 GPIOs, and a 128-pin TQFP package. It is designed for non-battery-powered USB peripheral equipment requiring high-speed USB connectivity, parallel data-transfer control, and programmable device-side firmware. An EZ-USB FX2LP is a highly integrated USB 2.0 microcontroller. It combines an 8051-compatible processing core, USB device-controller hardware, on-chip RAM, serial interfaces, and programmable general-purpose I/O in one device. Its position in the electronics hierarchy is USB interface controller → USB 2.0 peripheral controller → embedded microcontroller → semiconductor, placing it between a host computer and a USB-connected data-acquisition or control peripheral. The principal specifications are a 24 MHz operating clock, 16 KB of RAM, and 40 GPIOs in a 128-pin TQFP package. The device operates from a 3.0 V to 3.6 V supply, uses an 8-bit processor architecture, and provides serial debug support. These characteristics make it appropriate for instruments, adapters, test equipment, and embedded peripherals that need local control logic and a direct USB 2.0 interface rather than a separate host-side USB bridge. The FX2LP architecture is intended to handle USB protocol transactions while the 8051 core manages endpoint behavior, buffers, control requests, and application-specific data movement. The 16 KB RAM provides working memory for firmware and descriptors, while 40 GPIOs expose digital control and status signals to external circuitry. Serial debug supports firmware development and troubleshooting, reducing the need for additional diagnostic interfaces when the board design permits. Typical applications include high-speed USB oscilloscope and logic-analyzer front ends, test-and-measurement adapters, data-acquisition equipment, printer or scanner interfaces, industrial control adapters, and USB-to-parallel data bridges. The 40 available GPIOs are especially useful for status LEDs, control strobes, handshake signals, and discrete front-end controls. Its integrated USB controller can simplify system architecture by consolidating peripheral control and USB communication. When designing around the CY7C68013A-128AXC, verify the complete pin assignment, USB transceiver requirements, clocking arrangement, and external memory interfaces in the manufacturer datasheet before layout. A 128-pin TQFP package demands careful fanout and decoupling, while USB signal routing requires short, controlled impedance paths. Firmware must also be developed for the ROMless architecture and programmed into the target system through the supported configuration path. This page provides a design-focused overview of the 24 MHz clock, 16 KB RAM, 40 GPIO resources, 3.0 V to 3.6 V supply range, and TQFP-128 package. It also identifies same-package replacement candidates, application-fit guidance, comparison parameters, and practical PCB considerations that help engineers evaluate the controller before committing a new USB peripheral design.

RFC Hubungi kami
CY7C68013A-128AXI - 48MHz USB 2.0 Controller | Infineon
CY7C68013A-128AXI

CY7C68013A-128AXI - 48MHz USB 2.0 Controller | Infineon

The Infineon Technologies CY7C68013A-128AXI is an EZ-USB FX2LP high-speed USB 2.0 peripheral controller with an 8051 core, 16 KB of internal RAM, 40 GPIOs, and a 128-pin TQFP package. It operates from a 3 V to 3.6 V supply and supports USB 2.0 data rates exceeding 53 MB/s. The controller combines USB connectivity, programmable peripheral interfacing, and serial debugging in a single package. An EZ-USB FX2LP is a specialized USB microcontroller within the broader hierarchy of microcontrollers, USB peripheral controllers, interface ICs, and semiconductors. Unlike a conventional general-purpose MCU, the device integrates a USB 2.0 transceiver, programmable GPIF interface logic, and an 8051 processor into one integrated circuit. This architecture lets designers implement high-speed USB peripherals without relying on a discrete USB transceiver. Three headline capabilities define the CY7C68013A-128AXI: a 48 MHz 8051 core, a maximum USB 2.0 bandwidth above 53 MB/s, and 40 general-purpose I/O pins. The 16 KB internal RAM supports USB descriptor and endpoint configuration, while the serial debug interface assists firmware development and troubleshooting. Its integrated USB 2.0 transceiver also reduces external circuitry compared with solutions using a separate controller and transceiver. The FX2LP architecture uses a General Programmable Interface, or GPIF, to connect the USB controller to external FIFOs, processors, or peripherals. This programmable interface is central to high-speed data movement because it coordinates read and write timing without requiring every connected device to implement a complete USB stack. The 8051 processor remains responsible for initialization, control transfers, descriptor handling, and application-specific firmware. Typical uses include USB-to-FIFO data acquisition, industrial data loggers, oscilloscopes and logic analyzers, test equipment, custom USB bridges, and high-throughput peripheral adapters. Its 40 GPIOs can support control signals, status indicators, triggers, and chip selects. The 128-pin TQFP provides substantially more interface connectivity than small USB controller packages, making it suitable for designs that need both high-speed data transfer and extensive control logic. PCB design should preserve short, impedance-controlled USB differential traces and provide the decoupling and layout specified by the manufacturer datasheet. The numerous external pins also require careful fan-out between the fine-pitch TQFP and surrounding circuitry. Firmware development should account for the device's role as a USB bus master and use its serial debug facilities to validate enumeration before testing sustained high-speed transfers. This product page consolidates the key electrical characteristics, package information, verified drop-in options, comparison criteria, and application guidance needed to evaluate the CY7C68013A-128AXI before designing it into a USB 2.0 peripheral system.

RFC Hubungi kami
CY7C68013A-56BAXC - USB 2.0 Controller | Infineon
CY7C68013A-56BAXC

CY7C68013A-56BAXC - USB 2.0 Controller | Infineon

The Infineon CY7C68013A-56BAXC is an EZ-USB FX2LP high-speed USB 2.0 peripheral controller with a 24 MHz 8051-compatible core, 16 KB of internal RAM, and 24 GPIOs, packaged in a 56-ball BFVGA. It integrates the USB 2.0 transceiver and supports data transfer rates above 53 MB/s. An EZ-USB FX2LP is an application-specific USB microcontroller that combines a low-cost 8051 processor with programmable USB connectivity and general-purpose I/O. In the product hierarchy, it belongs to the USB controller and embedded microcontroller categories, with USB device control, data transfer, and peripheral interfacing forming its primary system roles. The integrated USB 2.0 transceiver eliminates the need for a separate transceiver when implementing a compliant USB peripheral. The controller provides 16 KB of RAM for firmware, data buffers, and descriptor information, while its GPIOs support status indicators, control signals, data lines, and external peripheral interfaces. Its compact 56-ball package is intended for space-constrained equipment. The FX2LP architecture can organize USB transfers into buffer descriptors and direct data movement between USB endpoints and external memory or peripherals. This architecture is useful when a product requires more than the simple fixed-function behavior of a basic USB interface. The 8-bit data bus and 24 MHz operating clock provide a straightforward connection to external memory, parallel logic, and acquisition hardware. Typical uses include USB-to-serial adapters, data acquisition devices, logic analyzers, test instruments, industrial interface equipment, and compact external storage controllers. The controller is especially relevant to logic analyzers because high-speed USB can move captured samples from a parallel acquisition engine to a host computer efficiently. Designers should use the manufacturer pin description table to assign the 56-ball footprint and verify routing of power, ground, clock, USB data, address, and data-bus signals. Firmware must initialize the USB endpoints, synchronize buffer descriptors with the host, and confirm timing and signal integrity on the completed board rather than relying only on device-level specifications. This product page combines the exact catalog attributes, packaging distinctions, family comparisons, and implementation guidance for engineers evaluating the CY7C68013A-56BAXC. It also distinguishes verified same-footprint alternatives from related package options that require PCB changes.

RFC Hubungi kami
CY7C68013A-56LTXC - Low-Power USB 2.0 Controller | Infineon
CY7C68013A-56LTXC

CY7C68013A-56LTXC - Low-Power USB 2.0 Controller | Infineon

Infineon Technologies CY7C68013A-56LTXC is an EZ-USB FX2LP low-power USB 2.0 peripheral controller with 16K RAM, 24 GPIOs, and a 56-pin QFN package. It integrates a USB 2.0 controller, 8051-compatible microcontroller, and USB transceiver in one device designed for non-battery-powered applications. A USB 2.0 peripheral controller is a specialized microcontroller that communicates with a USB host while exposing programmable data-transfer functions to the surrounding equipment. Its position in the hierarchy is USB interface controller → application-specific microcontroller → integrated circuit → semiconductor. The EZ-USB FX2LP architecture combines an 8-bit data-bus interface with dedicated USB control hardware, allowing portable peripherals, test equipment, and data-acquisition products to transfer data without implementing a complete USB host stack. The controller operates from 3 V to 3.6 V and uses a 24 MHz clock. The manufacturer describes 16K of embedded RAM, 24 GPIOs, and an integrated USB 2.0 transceiver. The 56-pin QFN construction supports compact PCB layouts, while the integrated transceiver avoids the additional area required by a separate USB transceiver. The architecture supports transfer rates exceeding 53 MB per second while using the maximum USB 2.0 bandwidth. The 8051-compatible core provides a familiar firmware platform, while the USB Serial Interface Engine handles low-level protocol functions and the controller’s parallel data path connects it to external data sources. Firmware can configure endpoint behavior, packet handling, and data movement between USB and the external 8-bit bus. This division of responsibilities allows a product to present a specialized USB peripheral function while reusing relatively simple external data-acquisition or buffering hardware. Typical uses include portable logic analyzers, test-and-measurement adapters, data-acquisition equipment, industrial peripherals, and compact USB-to-custom-interface products. The low-power design is particularly relevant to non-battery-powered equipment where the integrated transceiver and 3 V to 3.6 V operating range simplify power architecture. The controller is also suitable for designs requiring high-speed sustained transfers rather than low-rate control-only communication. When laying out the PCB, place the USB connector, differential data traces, and decoupling capacitors close to the controller. USB differential routing requires matched geometry and a continuous reference plane. Firmware developers should also account for the controller’s internal USB handling and external 8-bit data interface rather than treating it as a conventional general-purpose 8051 design. This page combines the manufacturer’s key device specifications with package, sourcing, comparison, and implementation guidance. It also distinguishes genuine same-package drop-in candidates from components that may provide similar USB functionality but require a different footprint, firmware strategy, or PCB redesign.

RFC Hubungi kami
CY7C68013A-56LTXI - USB 2.0 Controller | Infineon
CY7C68013A-56LTXI

CY7C68013A-56LTXI - USB 2.0 Controller | Infineon

Infineon Technologies CY7C68013A-56LTXI is an EZ-USB FX2LP USB 2.0 high-speed peripheral controller with an integrated 8051 microcontroller, 16 KB RAM, and 24 GPIOs, housed in a 56-pin QFN package with an exposed pad. The device is intended for non-battery-powered USB peripherals and combines USB protocol handling, direct data-path control, and general-purpose I/O in one package. An EZ-USB FX2LP is a specialized USB peripheral controller, a functional member of the broader microcontroller and USB interface-controller hierarchy. It integrates a USB 2.0 transceiver, an 8051-compatible control engine, and flexible endpoint data-path hardware. This integration can reduce the component count and board area required for high-speed USB peripherals compared with a separate USB serial interface engine and external transceiver. Key verified features include support for USB 2.0 high-speed operation, transfer rates reported above 53 MB/s, 16 KB of RAM, and 24 GPIOs. The 8051 core provides 24 MHz operation according to the retrieved component data, while an 8-bit data-bus architecture supports communication with external memory or peripheral logic. The controller is supplied in a 56-pin QFN package, making it suitable for compact USB peripheral equipment. The FX2 architecture places flexible FIFO and endpoint handling close to the USB interface. Designers can select among bulk, interrupt, and control endpoint behavior for compatible USB devices, subject to the endpoint and DMA resources documented by the manufacturer. This architecture is useful when a peripheral must move data continuously while the embedded control processor manages configuration, status, or protocol-specific commands. Typical applications include USB-to-serial bridges, data acquisition equipment, test and measurement instruments, industrial peripheral adapters, high-speed storage controllers, and other non-battery-powered USB devices. Its integrated transceiver and compact package make it especially useful where board area and external component count are important design constraints. When laying out the PCB, preserve the exposed-pad and thermal requirements shown in the manufacturer package documentation. USB differential routing should be short, impedance-controlled, and kept away from noisy switching nodes. Firmware configuration, endpoint allocation, clock requirements, and transceiver support circuitry should be validated against the manufacturer datasheet before production release. This product page combines the verified manufacturer description, distributor availability, package information, and cross-reference findings with practical selection guidance. It distinguishes confirmed drop-in candidates from alternatives that still require firmware, qualification, or sourcing review.

RFC Hubungi kami
CY7C68013A-56PVXC - 16KB USB 2.0 MCU | Infineon
CY7C68013A-56PVXC

CY7C68013A-56PVXC - 16KB USB 2.0 MCU | Infineon

The Infineon Technologies CY7C68013A-56PVXC is a ROMless 8051 EZ-USB FX2LP USB 2.0 peripheral controller with 16 KB RAM, 24 GPIOs and a 56-pin SSOP package for non-battery-powered applications. It supports a 3 V to 3.6 V supply range and integrates USB connectivity with programmable peripheral control, making it suitable for data acquisition, test equipment, storage interfaces and custom USB peripherals. A USB microcontroller is an application-specific microcontroller integrated with a USB controller and dedicated I/O. The EZ-USB FX2LP family combines an 8051-compatible processing core with high-speed USB 2.0 peripheral connectivity. Its programmable architecture allows designers to implement protocol-specific endpoints and move data between USB and external circuitry without relying on a conventional ROM-resident application program. The verified product information identifies the device as ROMless and equipped with 16 KB of RAM. Infineon specifies 24 GPIOs for non-battery-powered designs, while distributor data identifies the 8051 architecture, USB 2.0 operation and a 56-BSSOP package measuring approximately 0.295 inches wide. These features support compact USB peripheral designs that require flexible endpoint and data-path behavior. The FX2LP architecture is relevant to designs requiring USB high-speed data movement alongside parallel, serial or specialized peripheral interfaces. Exact endpoint count, transfer rates, oscillator options and electrical timing characteristics were not present in the supplied verification set and must be confirmed in the manufacturer documentation before design release. The part should be treated as a USB controller rather than a general-purpose host solution. Typical applications include USB oscilloscope and logic-analyzer front ends, data loggers, test-and-measurement adapters, printer interfaces, storage bridges and industrial acquisition modules. For portable equipment, the device is specifically identified for non-battery-powered applications, so power budget and suspend behavior should be reviewed against the final system requirements. A key design consideration is USB signal integrity. The SSOP footprint requires careful routing of the differential USB data pair, short return paths and a controlled ground plane. Firmware, external interface timing, clocking and power sequencing must be validated using the manufacturer reference documentation and the target USB host environment. This page consolidates verified manufacturer and distributor information, explicitly identifies missing technical data and separates the target device from unsupported replacement claims. It is intended to accelerate component identification while preserving the need for datasheet-level verification.

RFC Hubungi kami
CY7C68013A-56PVXI - 48MHz USB 2.0 Controller | Infineon
CY7C68013A-56PVXI

CY7C68013A-56PVXI - 48MHz USB 2.0 Controller | Infineon

The Infineon Technologies CY7C68013A-56PVXI is a ROMless EZ-USB FX2LP 8051 USB 2.0 peripheral controller with a 48 MHz clock, 16 KB of RAM, 24 general-purpose I/Os, and a 56-pin SSOP package. It combines an integrated USB 2.0 transceiver, USB Serial Interface Engine, and 8051-compatible microcontroller in one package, supporting high-speed USB data acquisition and control applications. An EZ-USB FX2LP controller is a specialized USB interface microcontroller that combines peripheral control logic with a fast USB 2.0 data path. Within the semiconductor hierarchy, it is a USB interface controller, application-specific microcontroller, and member of the EZ-USB FX2LP family. This integration reduces the component count required for USB-to-serial, data acquisition, test-and-measurement, and industrial peripheral designs. Three headline characteristics distinguish the CY7C68013A-56PVXI. Its 48 MHz 8051-compatible processor supports firmware-driven endpoint and transfer control, while 16 KB of on-chip RAM provides working storage for USB descriptors, buffers, and application state. Its 24 GPIOs provide direct peripheral interfacing, and the integrated USB 2.0 interface supports transfer rates exceeding 53 MB/s under suitable host and bus conditions. The device uses the FX2LP architecture in which programmable endpoint logic controls how USB data is transferred between the host and internal FIFOs. Firmware configuration determines endpoint type, maximum packet size, and buffer ownership. This flexibility is useful for synchronous transfers, bulk data movement, vendor-specific commands, and control/status functions. The ROMless architecture keeps the target firmware external, allowing application-specific USB behavior to be updated without changing the controller. Typical uses include high-speed data acquisition, logic analyzers, test equipment, USB-to-serial equipment, industrial measurement systems, and USB-connected peripherals. The 24 GPIOs can support external clocks, triggers, indicators, and interface signals, while the integrated transceiver supports direct USB connectivity when the board layout follows the manufacturer's reference guidance. A critical design consideration is USB signal integrity. Route D+ and D- as a controlled-impedance differential pair, minimize stubs and unnecessary vias, place termination and protection components close to the connector, and observe the required separation from noisy digital and switching-power paths. Firmware must also enumerate all 24 GPIOs correctly and handle suspend, resume, and bus-disconnect states. This page combines device specifications, commercial sourcing guidance, verified drop-in alternatives, application guidance, and practical PCB design notes. It helps engineers compare package, temperature, memory, GPIO, and USB-controller differences before committing a new design or maintaining an existing USB 2.0 peripheral.

RFC Hubungi kami
CY7C68014A-128AXC USB 2.0 FX2LP Controller | Infineon
CY7C68014A-128AXC

CY7C68014A-128AXC USB 2.0 FX2LP Controller | Infineon

The Infineon Technologies CY7C68014A-128AXC is a ROMless EZ-USB FX2LP USB 2.0 peripheral controller with 16 KB RAM, 40 GPIO ports, an 8-bit data bus, and a 24 MHz clock speed in a TQFP-128 package. Designed for USB 2.0 full-speed and high-speed peripheral applications, it integrates USB device functionality with an 8051-compatible core. An EZ-USB FX2LP is a USB 2.0 peripheral controller and application-specific microcontroller. In the broader hierarchy, it belongs to USB interface controllers, embedded microcontrollers, semiconductor ICs, and power-managed embedded processing systems. Unlike a conventional host controller, the device is intended to terminate a USB peripheral connection while providing programmable data-transfer and general-purpose I/O resources for external data-acquisition, communication, or control hardware. The controller provides 16 KB of internal RAM for firmware and data buffering, 40 GPIO ports for device-side control signals, and an operating supply range of 3.0 V to 3.6 V. Its 8-bit data interface supports integration with parallel data sources and sinks, while the integrated 24 MHz clock provides the timing reference for USB signaling and firmware execution. The low-power EZ-USB FX2LP architecture is particularly useful in battery-powered equipment that must balance USB connectivity against energy consumption. The CY7C68014A family is based on the highly integrated EZ-USB FX2 architecture. USB traffic is handled by dedicated controller logic, leaving the embedded processor available for application firmware. The 16 KB RAM can hold firmware, descriptors, status data, and transfer buffers, allowing a compact implementation without an external program-memory device. This ROMless architecture allows product-specific USB behavior to be programmed directly into the device. Typical implementations include USB data-acquisition equipment, USB-to-parallel interface adapters, industrial control modules, test and measurement instruments, communications equipment, and battery-powered portable peripherals. The 40 GPIO count can support chip selects, control strobes, status indicators, and external interface signaling, while the parallel data bus can connect the controller to sensors, converters, memories, or legacy peripheral logic. PCB design should preserve short USB traces, provide solid ground-plane continuity, and place support components close to their associated pins. Pay particular attention to power distribution, clock-related routing, input protection, and the requirements listed in the manufacturer datasheet for external memory, firmware programming, and USB signal routing. This page combines manufacturer device facts, package information, application guidance, drop-in replacement analysis, and engineering design notes. It is structured to help developers evaluate USB controller integration, PCB footprint constraints, firmware requirements, peripheral I/O planning, and direct replacement decisions without relying only on a catalog specification summary.

RFC Hubungi kami
CY7C68014A-56BAXC - 48MHz USB 2.0 Controller | Infineon
CY7C68014A-56BAXC

CY7C68014A-56BAXC - 48MHz USB 2.0 Controller | Infineon

The Infineon Technologies CY7C68014A-56BAXC is a low-power EZ-USB FX2LP USB 2.0 peripheral controller integrating a 48 MHz enhanced 8051-compatible microcontroller, USB 2.0 transceiver, Serial Interface Engine, and programmable peripheral interface in a 56-VFBGA package. The controller operates from a 3.3 V supply and supports USB 2.0 high-speed operation. Its ROMless architecture allows firmware to be loaded from an external source, making it suitable for products requiring flexible USB protocol behavior, custom device descriptors, or application-specific data transfer. An application-specific microcontroller is an integrated circuit optimized around a particular embedded control function rather than a general-purpose processor. The EZ-USB FX2LP belongs to the broader hierarchy of USB interface controller, peripheral controller, microcontroller, and integrated circuit. Its integrated USB 2.0 transceiver and Serial Interface Engine reduce the external circuitry required to implement a USB peripheral, while the enhanced 8051 processor handles endpoint configuration, data movement, and application-specific control logic. Key features include USB 2.0 high-speed certification, integration of the USB transceiver and Serial Interface Engine, a 48 MHz enhanced 8051-compatible processor, and support for programmable peripheral functions. The verified source data identifies this device as a ROMless 56-VFBGA component rated for 3.3 V operation. The USB-IF high-speed certification reference shown in the retrieved source data is TID #40440111. These characteristics make the device useful where a product must present a customized USB interface while retaining a compact embedded-control architecture. Typical uses include USB data acquisition, test and measurement adapters, industrial peripheral interfaces, communications equipment, and USB-to-protocol bridge products. In these systems, the controller can implement endpoint-specific buffering and low-speed or high-speed device behavior through firmware. Because the device is ROMless, the implementation must also account for external code storage, firmware loading, enumeration timing, and the timing relationship between firmware execution and USB bus activity. The principal design consideration is package and pin-level migration. This ordering code uses a 56-VFBGA package, so any replacement must preserve the exact land pattern, ball assignments, voltage requirements, USB behavior, and firmware interface. The verified replacement information identifies a drop-in relationship within the FX2LP family, but it does not establish several distinct MPNs that are simultaneously same-package and parameter-compatible enough to populate a full five-part drop-in list. This page consolidates distributor availability, family-level replacement information, application guidance, and package cautions into an engineering-oriented selection summary. It distinguishes verified device attributes from unavailable specifications and does not infer electrical or thermal values that are absent from the supplied source material.

RFC Hubungi kami
CY7C68014A-56LFXC - 8051 High-Speed USB Controller | Infineon
CY7C68014A-56LFXC

CY7C68014A-56LFXC - 8051 High-Speed USB Controller | Infineon

Infineon Technologies CY7C68014A-56LFXC is an application-specific 8051 EZ-USB FX2LP high-speed USB microcontroller in a 56-pin VFQFN exposed-pad package. Verified distributor information identifies the device as a ROMless USB microcontroller with an 8051 processor, an 8051 address/data bus, 16K RAM, and 40 GPIOs. These features position it as a dedicated USB peripheral controller for systems requiring programmable high-speed USB connectivity rather than a general-purpose application microcontroller. An EZ-USB FX2LP is a specialized USB interface controller within the broader microcontroller and USB interface IC hierarchy. Its integrated 8051 core allows endpoint and transfer behavior to be configured through firmware, while the address/data bus can connect external memory or companion logic when a design needs more storage or peripheral integration than the internal resources provide. Unlike a fixed-function USB interface, a ROMless controller allows product-specific USB behavior to be implemented in system firmware. The principal verified characteristics are the 8051 CPU architecture, ROMless configuration, 16K RAM, 40 GPIOs, high-speed USB operation, and 56-VFQFN exposed-pad packaging. The exposed pad supports heat transfer from the device to the PCB, although the available data does not state a package dimension, pinout, clock rate, electrical limits, temperature range, or thermal resistance. Those values must be confirmed in the manufacturer datasheet before release of a production design. The architecture is suited to USB peripheral equipment requiring deterministic firmware-controlled transfers, broad GPIO availability, and access to an external 8051-style address/data bus. The verified source material identifies high-speed USB peripheral control as a principal use, while another distributor listing categorizes the part as an application-specific microcontroller. These classifications reflect the device’s specialized role as a USB-connected control component rather than a general processor for embedded control. Typical implementation areas include high-speed USB test and measurement equipment, data-acquisition adapters, printer and scanner interfaces, industrial peripheral controllers, USB-to-serial bridges, and legacy-port upgrade products. The 40 GPIOs can support control signals, indicators, interlocks, and peripheral chip selects, while the 16K RAM provides the stated internal working-memory resource. External memory may be used where firmware and working data exceed the internal capacity. Board design should preserve the exposed-pad thermal path with an uninterrupted ground or power plane beneath the package, subject to the manufacturer’s land-pattern and assembly instructions. USB routing must follow the applicable high-speed layout guidance, including a controlled impedance path, continuous reference plane, minimized stubbing, and careful separation from noisy digital or switching nodes. Firmware should account for endpoint configuration, bus timing, and the function of every externally connected bus signal. This product record combines verified distributor identification, lifecycle information from the Infineon community article, and the manufacturer-backed drop-in relationship for CY7C68014A-56LTXC. It also separates confirmed specifications from unresolved electrical and mechanical details, helping engineers evaluate the controller without mistaking datasheet gaps for guaranteed performance.

RFC Hubungi kami
CY7C68014A-56LTXC - USB 2.0 Controller | Infineon
CY7C68014A-56LTXC

CY7C68014A-56LTXC - USB 2.0 Controller | Infineon

Infineon Technologies CY7C68014A-56LTXC is a ROMless EZ-USB FX2LP USB 2.0 peripheral controller with 16K RAM, 40 GPIOs, and a 24 MHz 8051-compatible core, housed in a 56-pin VFQFN exposed-pad package. It operates from 3 V to 3.6 V and combines an 8-bit data bus with dedicated USB, I2C, and USART connectivity. A USB peripheral controller is a semiconductor that manages communication between a USB host and an embedded processor. The EZ-USB FX2LP belongs to the broader USB controller, interface IC, and microcontroller hierarchy. By placing USB protocol handling and configurable data-path logic near the processor interface, it supports compact designs that need high-speed USB data transfer without a dedicated external USB transceiver. The device provides 16K RAM for endpoint and data-transfer use, 40 general-purpose I/O pins, and an 8-bit address/data interface for an external 8051 processor. Its 24 MHz operating clock supports USB 2.0 peripheral operation, while the 3 V to 3.6 V supply range suits compact battery-powered equipment. The package combines the controller with a low-power design intended for portable and embedded USB systems. The EZ-USB architecture separates USB-specific handling from the attached processor, allowing firmware to manage control requests and data movement. The 8051 address/data bus and 40 GPIOs provide flexible connections to storage, sensors, communications transceivers, and human-interface devices. I2C and USART interfaces add options for configuration and ancillary serial peripherals without requiring separate programmable logic. Typical applications include USB data acquisition, industrial instrumentation, test-and-measurement equipment, portable data loggers, external storage interfaces, and USB-to-serial or USB-to-I2C adapters. The ROMless architecture is particularly useful when system firmware, protocol policy, or endpoint behavior must be customized for the target product. Designers should verify the exposed-pad land pattern, local decoupling requirements, clock source, USB transceiver or connector integration, and external processor bus timing before layout release. Because this high-pin-count VFQFN package has no matching diagram in the selected package library, use the manufacturer pin-description table and package drawing for all PCB assignments and land-pattern decisions. This page combines manufacturer specifications, lifecycle information, verified drop-in candidates, package-level selection guidance, and practical design notes. It is intended to help engineers evaluate the CY7C68014A-56LTXC for custom USB 2.0 peripheral equipment while preserving the distinction between documented replacements and related family members.

RFC Hubungi kami
CY7C68014A-56PVXC - 16K RAM USB 2.0 Controller | Infineon
CY7C68014A-56PVXC

CY7C68014A-56PVXC - 16K RAM USB 2.0 Controller | Infineon

Infineon Technologies CY7C68014A-56PVXC is an EZ-USB FX2LP USB 2.0 peripheral controller with a 24 MHz 8051 processor, 16K RAM, 24 GPIOs, and a 56-pin BSSOP package. Designed as a ROMless application-specific microcontroller, it integrates USB device-control hardware with configurable general-purpose I/O for data acquisition, control, storage, and human-interface devices. The listed operating supply range is 3 V to 3.6 V. An EZ-USB FX2LP USB 2.0 peripheral controller is a specialized USB interface microcontroller rather than a general-purpose processor. It combines an 8051-compatible core with USB peripheral functions and programmable I/O, placing USB connectivity, control logic, and application-specific interfaces in one device. This hierarchy runs from USB 2.0 peripheral controller to application-specific microcontroller, interface controller, and integrated circuit. The controller uses 16K RAM for firmware and data buffering, while its ROMless architecture allows the application firmware to be loaded after reset. The 24 GPIOs support digital status inputs, control outputs, and peripheral signals. A 3 V to 3.6 V operating supply supports integration with 3.3 V systems, and the 8-bit data bus enables connection to external memory or application circuitry where required. The FX2LP architecture is intended for USB peripherals that require more application-specific control than a basic USB interface bridge. Its integrated USB 2.0 peripheral functionality reduces the need for a separate USB controller in suitable designs. The processor clock listed for this device is 24 MHz, providing a defined timing basis for USB enumeration, endpoint handling, data movement, and firmware execution. Typical uses include USB-connected test and measurement instruments, data-acquisition peripherals, industrial control interfaces, programming equipment, storage adapters, and compact human-interface devices. The 24 GPIOs are particularly useful when a design needs configurable control or monitoring signals in addition to USB communication. Battery-powered equipment is also an application focus for the low-power FX2LP family. Board design should follow the manufacturer pin-description table and recommended USB circuit layout. Keep high-speed USB traces short and controlled, provide the required 1.5-kohm pull-up behavior on the USB D+ line, and place bypass capacitance close to the supply pins. Confirm all signal levels, external memory connections, and programming connections against the device documentation before releasing the PCB. This product record combines the manufacturer identification, interface characteristics, package information, lifecycle status, and design-focused guidance in a format useful for engineering selection and sourcing. It also distinguishes verified drop-in alternatives from functionally similar controllers so that PCB compatibility can be evaluated before a component substitution is approved.

RFC Hubungi kami
CY7C68015A-56LFXC - USB 2.0 FX2LP Controller | Cypress
CY7C68015A-56LFXC

CY7C68015A-56LFXC - USB 2.0 FX2LP Controller | Cypress

The Cypress Semiconductor CY7C68015A-56LFXC is a ROMless EZ-USB FX2LP USB 2.0 microcontroller and high-speed USB peripheral controller with an integrated 8051 processor, smart Serial Interface Engine, and USB transceiver. The device operates from a 3.3 V supply and is packaged as a 56-VFQFN with an exposed pad. Its architecture combines USB connectivity, an enhanced 8051 microprocessor, and programmable GPIO in one controller IC. An EZ-USB FX2LP is a highly integrated USB 2.0 controller in the broader semiconductor and embedded-controller hierarchy. It is designed for low-power USB peripheral applications requiring high-speed data transfer, flexible endpoint control, and firmware-based protocol implementation. Unlike a simple USB interface adapter, the smart SIE can handle low-level USB transactions while the embedded processor manages device-specific behavior, data movement, and host communication. The verified product information identifies the CY7C68015A-56LFXC as a ROMless 8051 EZ-USB FX2LP USB microcontroller in a 56-VFQFN exposed-pad package. It supports USB 2.0 high-speed operation and includes a single-chip USB 2.0 transceiver, smart SIE, and enhanced 8051 microprocessor. The low-power FX2LP positioning is especially relevant to battery-powered and portable equipment where USB connectivity must coexist with constrained power budgets. The integrated architecture reduces the component count required for a USB peripheral design by combining protocol handling, control logic, and general-purpose processing. Programmable GPIOs can support control signals, indicators, and external interfaces, while the ROMless architecture allows the application firmware to be loaded according to the product's programming and boot architecture. Exact RAM, GPIO, clock, endpoint, and electrical limits must be confirmed in the current manufacturer datasheet before schematic release. Typical applications include USB-to-serial adapters, data acquisition equipment, test and measurement instruments, industrial peripheral interfaces, storage and communication adapters, and portable USB-connected products. The device is particularly useful where a host bus requires protocol-specific buffering or endpoint handling beyond a basic UART or SPI USB bridge. A critical design consideration is package and pinout verification. The supplied search results confirm the 56-VFQFN exposed-pad package but do not provide the complete numbered pin list, so the design must be checked against the manufacturer datasheet land pattern, exposed-pad connection, decoupling requirements, and signal-routing guidance before fabrication. This page consolidates verified distributor and manufacturer-listing information, same-package family alternatives, comparison fields, and practical design cautions. It separates confirmed facts from unavailable specifications so engineers can identify what still requires validation from the manufacturer datasheet.

RFC Hubungi kami
CY7C68015A-56LTXC - USB 2.0 Controller, 16KB RAM | Infineon
CY7C68015A-56LTXC

CY7C68015A-56LTXC - USB 2.0 Controller, 16KB RAM | Infineon

The Infineon CY7C68015A-56LTXC is a ROMless EZ-USB FX2LP USB 2.0 peripheral controller with a 48 MHz 8051 core, 16 KB of RAM, and 24 general-purpose I/O pins in a 56-VFQFN exposed-pad package. It operates from a 3 V to 3.6 V supply and supports USB, I2C, and USART interfaces for data acquisition, control, and USB-to-serial bridge designs. An EZ-USB FX2LP controller is an application-specific USB peripheral controller that combines a fast 8051-compatible microprocessor with dedicated USB 2.0 full-speed and low-speed device hardware. Within the product hierarchy, it is a USB interface controller, application-specific microcontroller, embedded processor, and USB 2.0 peripheral controller. Its RAM may be used for firmware, descriptors, endpoint buffers, and application data rather than storing a fixed program image in on-chip ROM. The principal features include 16 KB of RAM, 24 GPIOs, a 48 MHz core clock, and operation across a 3 V to 3.6 V supply range. USB connectivity is integrated on the device, while I2C and USART provide paths to sensors, EEPROMs, transceivers, and external interface controllers. These resources make the controller suitable for compact USB peripheral equipment where high-speed host-side data transfer must coexist with embedded control functions. FX2LP devices use an 8051-compatible architecture and register-based firmware programming. Endpoint configuration, descriptor handling, and data-transfer routines are implemented in firmware, allowing product behavior to be adapted without changing the external USB interface hardware. Exact endpoint-buffer capacity and all detailed electrical characteristics should be confirmed in the manufacturer datasheet for the final production design. Typical applications include USB-to-serial adapters, data-acquisition front ends, logic analyzers, oscilloscope interfaces, industrial control panels, test equipment, and portable instruments. The exposed-pad package supports compact surface-mount layouts, while the 3 V to 3.6 V operating range fits designs powered from regulated battery or USB-derived rails. PCB designers should follow the manufacturer pin-description table when assigning the exposed pad, supply pins, and ground connections. Place high-frequency decoupling capacitors close to the device, preserve the recommended USB data-routing geometry, and confirm that the PCB footprint and paste pattern match the 56-VFQFN package used by the selected ordering code. This page combines the manufacturer device description with family-level alternatives, package comparisons, sourcing guidance, and practical integration considerations. It is intended to help engineers determine whether the CY7C68015A-56LTXC fits a USB peripheral design before beginning firmware and PCB implementation.

RFC Hubungi kami
CY7C68016A-56LFXC - USB 2.0 FX2LP Microcontroller | Infineon
CY7C68016A-56LFXC

CY7C68016A-56LFXC - USB 2.0 FX2LP Microcontroller | Infineon

Infineon Technologies CY7C68016A-56LFXC is a low-power EZ-USB FX2LP USB 2.0 microcontroller with an integrated high-speed transceiver, smart Serial Interface Engine, enhanced 8051 processor, 3.3 V operating supply, and 56-pin VFQFN exposed-pad package. It is designed for USB high-speed peripheral applications requiring flexible data transfer and compact board space. An EZ-USB FX2LP microcontroller is an application-specific USB controller in the broader hierarchy of 8051 microcontrollers, embedded processors, and USB interface integrated circuits. It combines a USB 2.0-compatible transceiver and serial-interface engine with an internal enhanced 8051 core. This integration allows one device to manage endpoint buffering, USB transfers, and peripheral data movement without relying on a separate USB transceiver. Verified listings identify the CY7C68016A-56LFXC as a ROMless 8-bit EZ-USB FX2LP device with USB, I2C, and USART interfaces. Its operating supply range is 3 V to 3.6 V, and its listed operating temperature range is 0 °C to 70 °C. The USB 2.0 implementation is USB-IF high-speed certified under TID 40440111. Its SMD package is a 56-pin VFQFN with an exposed pad and is supplied in a tube according to the verified distributor data. The controller’s integrated architecture reduces USB-interface component count by combining the transceiver, smart SIE, and enhanced 8051 processor in one package. Firmware controls endpoint configuration and data transfer behavior, while the processor handles application-specific processing. Because the device is ROMless, the design must provide a suitable firmware-programming and boot solution, and developers must budget memory appropriately for USB descriptors, endpoint logic, and application code. Typical uses include high-speed USB data acquisition, USB-to-serial and USB-to-parallel adapters, test and measurement equipment, data-logging systems, industrial peripherals, and consumer USB accessories. The 56-VFQFN exposed-pad package also requires careful PCB layout and thermal management so heat can transfer through its exposed pad while preserving high-speed USB signal integrity. A primary design consideration is the 3.0 V to 3.6 V supply constraint: the part cannot be connected directly to a 5 V USB VBUS rail without an appropriately designed power path. Layout should follow the manufacturer’s pin, differential-routing, decoupling, and exposed-pad guidance, while production firmware and connector behavior should be validated against the complete USB design. This page consolidates verified distributor specifications, package information, lifecycle-oriented cross-reference results, and practical replacement guidance that is not presented as a single-source manufacturer summary. It also distinguishes true same-footprint drop-in candidates from broader USB-controller alternatives that require firmware or hardware changes.

RFC Hubungi kami