Mikropengawal

Produk (20,000+)

PIC16C710-04I/P - 8-Bit 4MHz OTP MCU, 13 I/O, 4-CH ADC | Microchip
PIC16C710-04I/P

PIC16C710-04I/P - 8-Bit 4MHz OTP MCU, 13 I/O, 4-CH ADC | Microchip

The Microchip PIC16C710-04I/P is an 8-bit RISC microcontroller in the PIC16C family, featuring a 4 MHz maximum clock speed, 896 bytes (512 x 14) of One-Time-Programmable (OTP) program memory, 36 bytes of data RAM, and 13 digital I/O pins, all housed in a 18-pin PDIP (Plastic DIP) through-hole package. It integrates a 4-channel 8-bit Analog-to-Digital Converter (ADC), making it a complete mixed-signal solution for entry-level embedded designs. What is a PIC microcontroller? A PIC (Peripheral Interface Controller) is a family of 8/16/32-bit RISC microcontrollers originally developed by Microchip Technology. Within the broader taxonomy, PIC16C devices are CMOS, OTP-based members of the 8-bit mid-range family, sitting between PIC10/12/16 baseline devices and PIC18 enhanced devices. They are widely deployed where deterministic behavior, low cost, and ease of programming are prioritized over raw performance. The PIC16C710's 4-channel 8-bit ADC lets designers read analog sensors directly without an external ADC, while its 13 I/O pins drive LEDs, switches, keypads, and low-speed communication lines. The '04' speed grade and 4 MHz oscillator/clock option target low-EMI applications, and the 'I' suffix indicates the industrial temperature range (-40C to +85C). The OTP program memory is one-time programmable - cost-effective for volume production but not re-programmable. Architecturally, the device uses Microchip's Harvard RISC architecture with separate program and data buses, 35 single-word instructions, and a 14-bit instruction word. The integrated ADC samples at a programmable rate and can be triggered from software or from a Timer overflow. Power management is handled via Sleep mode and a selectable oscillator, allowing current draw to drop below a few microamps for battery-friendly designs. Typical applications include appliance control panels, automotive sensor interfaces (basic), industrial control boards, and consumer electronics requiring analog input and minimal digital logic. The 'I/P' package (industrial temperature, 18-pin PDIP) is well suited for prototyping on breadboards and for through-hole production assemblies. The same die is also available in 18-pin SOIC and 20-pin SSOP packages for surface-mount designs. A key design consideration is OTP memory: firmware must be fully verified before programming because OTP cannot be erased or rewritten. Designers planning iterative development cycles should evaluate the Flash-based PIC16F equivalents (e.g., PIC16F716) for development, then move to the OTP PIC16C710 for production cost savings.

RFC Hubungi kami
PIC16C710-04I/SO - 8-bit 4MHz OTP MCU, 18-SOIC | Microchip
PIC16C710-04I/SO

PIC16C710-04I/SO - 8-bit 4MHz OTP MCU, 18-SOIC | Microchip

The Microchip Technology PIC16C710-04I/SO is an 8-bit RISC CMOS microcontroller from the PIC16C71X family, operating at up to 4 MHz and delivering 896 bytes (512 x 14 words) of One-Time-Programmable (OTP) program memory in an 18-pin SOIC package. The part integrates 36 bytes of RAM, 13 general-purpose digital I/O pins, a 4-channel 8-bit Analog-to-Digital Converter (ADC), and a watchdog timer in a single industrial-temperature device, making it a self-contained embedded controller for cost-sensitive analog-front-end designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (ROM/Flash/OTP), working RAM, and peripheral interfaces. PIC microcontrollers use a Harvard RISC architecture with separate program and data buses, enabling single-cycle instruction execution. The PIC16C7X family sits in Microchip's mid-range portfolio, balancing instruction simplicity, low cost, and analog integration. It belongs to the broader 8-bit MCU category alongside 8051, AVR, and other legacy architectures, and feeds into the larger hierarchy of microcontrollers > embedded processors > semiconductors. Key features of the PIC16C710-04I/SO include 4 MHz maximum clock, 4-channel 8-bit ADC with 25 us conversion time, 13 digital I/O lines, 36 bytes of data RAM, an operating voltage range of 2.5 V to 6.0 V, and an industrial temperature grade (-40 C to +85 C). The OTP program memory is factory- or field-programmable one time only, which simplifies production for high-volume fixed-code applications while reducing per-unit cost compared to flash-based devices. The architecture combines a 14-bit instruction word with a separate 8-bit data path. A 2-level hardware stack, 8-bit timer/counter with programmable prescaler, watchdog timer with its own on-chip RC oscillator, and a power-on reset (POR) circuit are all integrated. Brown-out protection and a power-saving SLEEP mode reduce system-level current draw for battery-operated use cases. Typical applications include entry-level A/D signal conditioning in automotive sensors, white-goods control boards, simple industrial monitoring loops, and consumer-appliance user-interface controllers. The 4-channel ADC is well-suited to multi-sensor reading, while the small 18-SOIC footprint supports compact PCB layouts. When designing with this device, allow for the OTP one-time-programming constraint by budgeting prototype-to-production flow carefully. Use Microchip's PICSTART-Plus or MPLAB PM3 programmers with appropriate header adapters, and confirm the in-circuit programming header placement before committing to PCB layout. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the bare manufacturer datasheet.

RFC Hubungi kami
PIC16C710-04I/SS - 8-Bit 4MHz OTP MCU with 8-bit ADC | Microchip
PIC16C710-04I/SS

PIC16C710-04I/SS - 8-Bit 4MHz OTP MCU with 8-bit ADC | Microchip

The Microchip Technology PIC16C710-04I/SS is an 8-bit CMOS OTP (One-Time-Programmable) RISC microcontroller in a 20-pin SSOP package, running at 4MHz with 200ns instruction execution. It integrates 896 bytes of program memory (512 x 14 words), 36 bytes of RAM, and a 4-channel 8-bit Analog-to-Digital Converter, making it suited for entry-level mixed-signal applications in automotive, industrial, appliance, and consumer markets. The industrial temperature grade (-40C to +85C) suffix "/I" qualifies the part for harsh-environment deployments. An MCU (Microcontroller Unit) is a single-chip computer that integrates a CPU core, program memory (ROM/Flash/OTP), working RAM, and peripheral interfaces such as ADC, timers, and I/O. The PIC16C710 belongs to Microchip's mid-range PIC16CXX family, employing a RISC (Reduced Instruction Set Computer) architecture with only 35 single-word instructions, eight-level deep hardware stack, and multiple internal/external interrupt sources. This lineage is upwards-compatible with the PIC16C5X and PIC12CXXX baselines, easing legacy firmware migration. Key features of the PIC16C710-04I/SS include 13 digital I/O pins, a Watchdog Timer with on-chip RC oscillator for reliable operation, power-saving Sleep mode, in-circuit serial programming capability via two pins, and an 8-bit Timer0/1 with programmable prescaler. The on-chip 4-channel 8-bit ADC delivers 20us conversion time, sufficient for low-speed sensor acquisition such as temperature, light, or potentiometric feedback in closed-loop control. Brown-out Reset circuitry protects against low-voltage corruption of program execution. The CMOS fully-static design eliminates the need for a minimum clock rate, allowing the device to operate from DC up to its 4MHz maximum. Program memory is OTP, meaning each unit can be programmed exactly once - appropriate for high-volume production but unsuitable for development cycles that require reprogramming. The SSOP-20 (5.3 mm body width, 0.65 mm pitch) footprint offers a compact outline while remaining hand-solderable for prototyping. Typical applications include white-goods and HVAC control boards, automotive sensor interfaces (battery monitors, lighting controls), battery chargers, small motor controllers, and consumer products such as coffee machines, washing machines, and security keypads. The integrated ADC enables direct connection to analog sensors without external signal conditioning. Designers should pair the PIC16C710-04I/SS with a decoupling 100nF ceramic capacitor on VDD placed within 5 mm of the pin, follow Microchip's recommended oscillator layout, and reserve the MCLR pin for either a reset switch or proper pull-up. For prototype work, consider the pin-compatible PIC16F710 Flash variant to enable firmware iteration. This page synthesizes distributor pricing, parametric cross-reference data, and practical design notes that complement, but do not replace, the manufacturer datasheet.

RFC Hubungi kami
PIC16C710-20/P - 8-bit OTP MCU, 20MHz, 13 I/O | Microchip | DIP-18
PIC16C710-20/P

PIC16C710-20/P - 8-bit OTP MCU, 20MHz, 13 I/O | Microchip | DIP-18

The Microchip Technology PIC16C710-20/P is an 8-bit CMOS microcontroller from the PIC16CXX mid-range family, delivering 20 MHz operation, 896 bytes of One-Time-Programmable (OTP) program memory (0.875 KB / 512 x 14 words), and 36 bytes of data RAM, packaged in a 18-pin PDIP through-hole enclosure (0.300 inch / 7.62 mm row spacing). Background: A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and programmable peripherals into one package. PIC16 mid-range MCUs are 14-bit instruction-word Harvard-architecture devices widely used for cost-sensitive embedded control. PIC16C-series parts use One-Time-Programmable EPROM rather than flash, meaning the program memory can be written once and is then read-only for the rest of its operational life. Within the PIC taxonomy, the PIC16C710 sits under mid-range 8-bit MCUs -> PIC microcontrollers -> microcontrollers -> microcontrollers & processors -> semiconductors. Key features include 4 channels of 8-bit Analog-to-Digital conversion on-chip, 13 digital I/O pins with programmable direction registers, a 20 MHz external oscillator input, an 8-bit timer/counter (TMR0) with an 8-bit prescaler, a Watchdog Timer with its own on-chip RC oscillator, and a Power-on Reset / Brown-out Reset combined circuit. The core is fully static CMOS, draws low operating current, and supports DC to 20 MHz clock input. Power supply range is 3.0 V to 6.0 V. Typical applications include entry-level A/D conversion in automotive sensor interfaces, industrial appliance controls, white goods and HVAC controls, and consumer-electronics user-interface boards where cost per node matters and the 4-channel 8-bit ADC is sufficient for the measurement task. Designers should reserve the four analog channels (RA0-RA3) for signals, use the remaining PORTA/B pins for digital I/O, and budget the OTP window-planning tool from Microchip before committing code. Power sequencing should respect the on-chip POR/BOR thresholds to avoid spurious reset events during brown-outs.

RFC Hubungi kami
PIC16C710-20/SO - 8-Bit OTP MCU 20MHz 4ch ADC SOIC-18 | Microchip
PIC16C710-20/SO

PIC16C710-20/SO - 8-Bit OTP MCU 20MHz 4ch ADC SOIC-18 | Microchip

The Microchip PIC16C710-20/SO is an 8-bit CMOS One-Time-Programmable (OTP) RISC microcontroller built on Microchip's PIC16CXX mid-range architecture, offered in a 18-pin SOIC (SO) commercial-temperature package. It executes instructions in 200 ns at 20 MHz from a single 5V supply and integrates 896 bytes of program memory, 36 bytes of data RAM, 13 general-purpose I/O pins, and a 4-channel 8-bit analog-to-digital converter. What is a PIC16CXXX microcontroller? The PIC16C family is Microchip's classic mid-range OTP-based 8-bit MCU line built around a Harvard RISC architecture that separates program and data memory. The PIC16C710 specifically combines a 14-bit instruction word, 8-bit data path, on-chip ADC, brown-out reset, and Timer0 in a compact 18-pin package. The 35 single-word instruction RISC core delivers ~5 MIPS at 20 MHz, and the integrated analog peripherals enable mixed-signal sensing without an external ADC. Key features include 4 channels of 8-bit A/D conversion (with one channel shared with the external voltage reference pin), an 8-bit Timer0 with an 8-bit programmable prescaler, brown-out reset (BOR) circuitry for reliable power-on behavior, an internal RC oscillator option, and wide operating voltage range from 3.0V to 6.0V. Power management includes sleep mode with wake-up via interrupt or watchdog timer, supporting battery-friendly designs. The 18-pin SOIC package measures 7.50 mm body width with standard 1.27 mm pitch. The PIC16C710 uses an enhanced CMOS process with static operation and a wide operating voltage window, with power dissipation rated below 1 W in active mode and a fraction of that in idle/sleep. The brown-out reset threshold is internally set to approximately 4.0V, guarding against VDD brown-out conditions that could corrupt program execution. Programming is via ICSP for development prototypes, while production units ship with one-time-programmable EPROM for cost-sensitive volume. Typical applications include white goods and appliance control boards, automotive body modules (under-hood and cabin), battery chargers, power-supply monitoring, HVAC sensor interfaces, and low-cost consumer products with mixed digital and analog requirements. The 4-channel 8-bit ADC is particularly well-suited to thermocouple, thermistor, potentiometer, or current-sensing front-ends. When designing with the PIC16C710-20/SO, place decoupling capacitors (0.1 µF ceramic plus 10 µF bulk) as close as possible to VDD/VSS pins and reserve the MCLR pin for an external reset network. For ADC accuracy, drive unused analog inputs to either rail and average multiple conversions to reduce noise. This page synthesizes distributor pricing, parametric drop-in alternatives from Microchip's pin/code compatibility chart, and design notes drawn from Microchip application notes and datasheet typical application circuits.

RFC Hubungi kami
PIC16C710-20/SS - 8-Bit MCU 896B OTP 13 I/O 20MHz SSOP | Microchip
PIC16C710-20/SS

PIC16C710-20/SS - 8-Bit MCU 896B OTP 13 I/O 20MHz SSOP | Microchip

The Microchip PIC16C710-20/SS is an 8-bit CMOS RISC microcontroller from Microchip's PIC16CXX mid-range family, featuring 896 bytes of one-time-programmable (OTP) program memory, 36 bytes of data RAM, 13 general-purpose I/O lines, and four channels of 8-bit Analog-to-Digital conversion in a 20-pin SSOP (0.209", 5.30mm width) package rated for 20 MHz operation. The OTP-based program memory and 4-channel ADC integration make this MCU a practical choice for entry-level mixed-signal designs where on-chip signal acquisition removes the need for an external ADC. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, data RAM, I/O peripherals, and (in this case) an analog-to-digital converter on a single die. The PIC16C71X family targets cost-sensitive, mixed-signal embedded applications, occupying the mid-range tier in Microchip's PIC architecture hierarchy (PIC10/12/14/16/18/24/32). The PIC16C710's 8-bit RISC core executes most instructions in a single instruction cycle, providing deterministic throughput at clock rates up to 20 MHz. As part of the mid-range family, it sits below the PIC18 and dsPIC families in instruction richness and addressing capability, but above the PIC10/12 baseline families in peripheral integration. Key features include 4-channel 8-bit ADC with selectable reference, 13 digital I/O pins multiplexed with peripheral functions, a 14-bit instruction word, Harvard bus architecture separating program and data memory, and integrated Brown-Out Detect (BOD) and Power-On Reset (POR). The 8-bit ADC provides up to 4 single-ended input channels with conversion times suitable for low-bandwidth analog sampling. The SSOP-20 footprint balances board-area savings with hand-solder-friendly lead pitch and offers better thermal dissipation than smaller QFN packages at moderate clock frequencies. The PIC16C710 uses a modified Harvard architecture with separate program and data buses, allowing simultaneous instruction fetch and operand access. The OTP program memory is field-programmable, meaning each device is programmed once and cannot be electrically erased; this makes the part ideal for low-to-medium volume production where flash reprogrammability is not required. The integrated 8-bit ADC uses successive-approximation conversion with a configurable clock source, supporting both ratiometric measurements with VDD as the reference and absolute measurements using an external reference. Typical applications include automotive sensor interface nodes, industrial control front-ends, appliance control boards, and consumer product analog front-ends. Designers commonly pair the PIC16C710 with external op-amps for signal conditioning, EEPROM for non-volatile parameter storage, and discrete RS-232 or RS-485 transceivers for legacy communication links. The 20 MHz top clock speed provides 5 MIPS of throughput, ample for polling-based control loops and slow-protocol UART links. When designing with this device, note that OTP programming means firmware cannot be updated in the field; budget time for one-time prototypes using the UV-erasable PIC16C71 (windowed CERDIP) variant for development, then move to the PIC16C710-20/SS for production. Provide adequate decoupling near the VDD pin and route the ADC analog inputs away from high-frequency digital traces to preserve conversion accuracy. This page synthesizes distributor pricing, package-specific drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers and procurement teams a faster decision base for the PIC16C710-20/SS.

RFC Hubungi kami
PIC16C710-20E/P - 8-Bit 20MHz OTP MCU 18-PDIP | Microchip
PIC16C710-20E/P

PIC16C710-20E/P - 8-Bit 20MHz OTP MCU 18-PDIP | Microchip

The Microchip PIC16C710-20E/P is an 8-bit CMOS RISC microcontroller from the PIC16C7X family with 4 channels of 8-bit Analog-to-Digital (A/D) converter, 896 bytes of OTP program memory (512 x 14 words), 36 bytes of RAM, and 13 bidirectional I/O pins, housed in an 18-pin PDIP through-hole DIP package. An 8-bit microcontroller (MCU) is a single-chip computer containing a CPU, program memory, data RAM, and peripherals such as timers and ADCs. The PIC16C7X family sits within Microchip's mid-range PIC16 architecture, between the baseline PIC10/12/16 series and the high-pin-count PIC17/18 series. The integrated 8-bit ADC allows direct measurement of analog sensors without an external converter, which historically made the PIC16C710 a popular entry-level mixed-signal controller. Key features of the PIC16C710-20E/P include a 20 MHz maximum operating frequency, 8-bit Timer0 with 8-bit prescaler, brown-out detection circuitry for Brown-out Reset (BOR), 13 individually-direction-controlled I/O pins, and 14-bit instruction word architecture. The 5V operating voltage and 20 MHz clock deliver roughly 5 MIPS of throughput, suitable for simple control loops, sensor reading, and user-interface scanning. The 18-pin PDIP package is pin-compatible with the PIC16C711 and is widely used in legacy through-hole designs. Internally, the PIC16C710 uses a Harvard architecture with separated program and data buses, an accumulator-based ALU, and a single hardware stack. The 8-bit ADC has 4 input channels multiplexed onto a single sample-and-hold, with the conversion clock derived from the system oscillator. Brown-out Reset protects against code corruption when VDD drops below the BOR threshold. Typical applications include entry-level automotive body controllers, industrial sensor interfaces, appliance control boards, and consumer devices. The 4-channel ADC is particularly well-suited for monitoring multiple analog sensors - for example temperature, pressure, and humidity - in a single low-cost MCU. When designing with this device, ensure the system oscillator configuration matches the application's timing needs (RC, XT, HS, or LP modes), and that BOR is enabled for robust power-up behavior. The 18-pin PDIP footprint also makes the part suitable for breadboard prototypes and educational use. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for sourcing, replacement, and application guidance on this legacy PIC MCU.

RFC Hubungi kami
PIC16C710-20E/SO - 8-Bit OTP MCU 20MHz 4xADC | Microchip
PIC16C710-20E/SO

PIC16C710-20E/SO - 8-Bit OTP MCU 20MHz 4xADC | Microchip

The Microchip Technology PIC16C710-20E/SO is a low-cost, high-performance CMOS 8-bit microcontroller from the PIC16CXX mid-range family, integrating 4 channels of 8-bit Analog-to-Digital (A/D) conversion in an 18-pin SOIC package. The device is built around a RISC core running at up to 20 MHz and includes 896 bytes of program memory (512 x 14 OTP) plus 36 bytes of general-purpose RAM, targeting entry-level A/D applications in automotive, industrial, appliance and consumer markets. A microcontroller (MCU) is a single-chip computer containing a processor core, program memory, data RAM and integrated peripherals. The PIC16C71X family is a fully-static mid-range family with a 14-bit instruction word, separated program and data buses, and an 8-level deep hardware stack, sitting within the broader PIC16CXX hierarchy (PIC16CXX -> PIC mid-range -> 8-bit microcontroller -> embedded MCU). OTP (One-Time Programmable) memory is non-volatile, retains code without power, and can be written only once during production. Key features of the PIC16C710-20E/SO include a 4-channel 8-bit ADC with selectable reference sources, an internal 4 MHz RC oscillator plus support for external crystal/RC oscillator modes, a 20 MHz maximum operating frequency, a wide 3.0 V to 6.0 V supply range, and a Power-on Reset (POR) / Brown-out Reset (BOR) mechanism. The 18-pin SOIC variant specified by the "/SO" suffix provides a 7.50 mm (0.295 in) wide gull-wing surface-mount package suitable for standard 300-mil SOIC-18 land patterns. Architecturally, the device uses a Harvard-style bus with separate program and data paths, allowing an instruction fetch and a data access to occur in a single instruction cycle. The integrated ADC samples analog inputs through a successive-approximation register (SAR) converter, while the reset and watchdog subsystems increase robustness in electrically noisy environments. Power management is achieved through Sleep mode with Wake-on-pin-change, drawing microamp-level standby current. Typical applications include analog sensor front-ends in automotive body controllers, industrial process monitoring, white-goods and appliance control boards, low-cost consumer products requiring on-board ADC, and battery-powered measurement nodes where 5V operation and OTP code security are important. When designing with this device, note that OTP memory requires one-time programming during manufacturing, so plan code revisions and firmware validation carefully before mask commitment. Ensure decoupling capacitors are placed close to VDD/VSS, and verify that analog input signals stay within the selected reference range to avoid ADC saturation. This page synthesizes distributor pricing, drop-in alternatives and practical design notes not found in the manufacturer datasheet alone, helping engineers shorten sourcing and qualification cycles.

RFC Hubungi kami
PIC16C710-20E/SS - 8-Bit 20MHz OTP MCU with ADC | Microchip
PIC16C710-20E/SS

PIC16C710-20E/SS - 8-Bit 20MHz OTP MCU with ADC | Microchip

The Microchip Technology PIC16C710-20E/SS is an 8-bit CMOS RISC microcontroller with integrated analog-to-digital converter, operating at up to 20 MHz instruction execution (200 ns instruction cycle) with 896 bytes of One-Time Programmable (OTP) program memory organized as 512 × 14 bits. It is housed in a 20-pin SSOP (Shrink Small Outline Package) with gull-wing leads and belongs to the automotive temperature grade (–40 °C to +125 °C), designated by the "E" suffix. The device belongs to the PIC16CXX mid-range family and offers 13 general-purpose I/O pins, a Timer0 8-bit timer/counter with 8-bit prescaler, four channels of 8-bit A/D conversion, brown-out reset (BOR) circuitry, and a watchdog timer. A microcontroller (MCU) is a single integrated circuit that contains a processor core, program memory, working RAM, and multiple peripherals such as timers, communication interfaces, and analog-to-digital converters. Microcontrollers sit at the heart of embedded systems, executing firmware to control sensors, actuators, displays, and communication links. Within the broader semiconductor taxonomy, an MCU belongs to the logic/Integrated Circuits > Microcontrollers category, and more specifically to the PIC mid-range family descended from Microchip's original Harvard-architecture PIC design. The PIC16C71X series adds on-chip ADC, making it suitable for mixed-signal embedded designs where analog sensing must coexist with digital control logic. Key features of the PIC16C710 include 36-byte general-purpose RAM, 64-byte EEPROM data memory (note: this part is OTP program + no separate EEPROM, only data EEPROM emulation in some variants), four 8-bit ADC channels with selectable reference, internal and external interrupt sources, and a programmable code-protection mechanism. The wide 2.5 V to 6.0 V operating voltage range supports both 3.3 V and 5 V system designs, and the 20 MHz clock rate provides 5 MIPS of processing throughput for real-time control loops. Architecturally, the PIC16C710 uses a 14-bit instruction word with single-cycle execution except for branch instructions, which take two cycles. The Harvard architecture separates program and data memory buses, eliminating the fetch-decode bottleneck of von Neumann designs. The 8-bit ALU and 8-bit working register (W) handle arithmetic and logic operations, while 36 general-purpose RAM bytes serve as data storage with direct and indirect addressing modes. Typical applications include automotive sensor signal conditioning, industrial control with analog inputs, appliance controls, battery chargers, and low-cost consumer devices. The combination of integrated ADC, ample I/O, and OTP programmability makes it well-suited for production-grade designs where code stability and small footprint are priorities. Design consideration: the OTP nature of program memory means firmware must be fully validated before production programming—once programmed, the code cannot be changed. For prototyping or field-upgradable designs, Flash-based PIC16F equivalents are typically preferred.

RFC Hubungi kami
PIC16C710-20I/P - 20MHz 8-bit OTP MCU 4xADC | Microchip
PIC16C710-20I/P

PIC16C710-20I/P - 20MHz 8-bit OTP MCU 4xADC | Microchip

The Microchip Technology PIC16C710-20I/P is a CMOS, fully-static, 8-bit microcontroller based on Microchip's powerful PIC architecture with 200 ns instruction execution, packed into an 18-pin DIP (PDIP) package. The device integrates 4 channels of 8-bit Analog-to-Digital conversion, 896 bytes of OTP program memory (512 x 14), 36 bytes of RAM, and 13 I/O pins. The "-20" suffix indicates a 20 MHz maximum clock frequency, and "I" designates the industrial operating temperature grade of -40C to +85C. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (ROM/RAM), and peripherals such as timers, communication interfaces, and increasingly analog blocks like ADCs. In the broader system hierarchy, the PIC16C710 sits under: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. OTP (One-Time Programmable) versions use EPROM-based program memory that can be programmed once and is well-suited to mature, volume-production designs where code stability has been validated. Key features of the PIC16C710-20I/P include a powerful PIC RISC architecture with only 35 single-word instructions to learn, an 8-bit Timer0 with 8-bit prescaler, integrated Brown-out Reset (BOR) for reliable operation during supply dips, 4-channel 8-bit ADC, and 13 digital I/O pins. The 18-pin PDIP package provides through-hole mounting for prototyping, legacy designs, and harsh-environment industrial equipment where socketed or wave-soldered assembly is preferred over surface-mount. Technically, the PIC16C710-20I/P uses a 14-bit instruction word with an 8-bit data path, delivering deterministic interrupt latency and predictable timing suitable for motor control and sensor read applications. The 4-channel ADC supports successive-approximation conversion with selectable reference voltages, while the BOR circuit protects against code corruption during brown-out events. Power consumption is minimized through SLEEP mode with wake-up capability via interrupts. Typical applications include automotive entry-level A/D subsystems, industrial sensor interfaces, consumer appliance controllers, and legacy retrofit designs requiring drop-in 18-pin through-hole microcontrollers. The OTP-based memory suits production runs where field firmware updates are not required. When designing with this device, ensure the Vdd supply is decoupled with 100 nF + 10 uF bulk capacitors placed close to the IC pins. Configure the ADC acquisition time to meet the source impedance of the analog signals to preserve 8-bit conversion accuracy, and verify the BOR trip voltage matches your supply rail tolerance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet cover page, providing an engineering decision baseline for sourcing PIC16C710-20I/P.

RFC Hubungi kami
PIC16C710-20I/SS - 8-bit MCU, 20MHz, 4-CH 8-bit ADC | Microchip
PIC16C710-20I/SS

PIC16C710-20I/SS - 8-bit MCU, 20MHz, 4-CH 8-bit ADC | Microchip

The Microchip Technology PIC16C710-20I/SS is an 8-bit CMOS RISC microcontroller with 875 bytes of EPROM program memory, 36 bytes of RAM, and 13 digital I/O lines, integrated in a 20-pin SSOP (Shrink Small Outline Package) surface-mount package. It operates at up to 20 MHz clock speed and features a 4-channel 8-bit analog-to-digital converter, making it ideal for entry-level A/D applications across automotive, industrial, appliance, and consumer market segments. A PIC microcontroller (Peripheral Interface Controller) is a family of Harvard-architecture, RISC-based, single-chip microcontrollers designed for embedded control. The PIC16C71x mid-range family specifically adds an integrated multi-channel ADC to the baseline PIC16CXX core, sitting in the product taxonomy: 8-bit MCU -> microcontroller -> embedded controller -> semiconductor IC. This hierarchy of analog integration with deterministic instruction execution makes the PIC16C71x well suited for mixed-signal embedded designs where a separate ADC would add cost, board area, and BOM complexity. Key features include 13 I/O pins with individual direction control, a 4-channel 8-bit ADC with selectable reference voltages, a programmable watchdog timer, power-on reset, power-saving SLEEP function, and an industrial-grade operating temperature range of -40C to +85C. The 20 MHz oscillator delivers 5 MIPS instruction throughput while consuming typical low supply current, and the EPROM program memory allows rapid prototyping and field-reprogrammable code updates during development cycles. Architecturally, the PIC16C710 uses a 14-bit instruction word with a two-stage pipeline, separating program and data memory (Harvard architecture) to enable simultaneous instruction fetch and operand access. The integrated ADC uses successive-approximation conversion with sample-and-hold circuitry, and the device supports both RC and crystal oscillator modes to balance cost versus timing accuracy in space-constrained designs. Typical applications include sensor signal conditioning, battery monitoring, simple closed-loop control, white-goods user interfaces, and low-cost industrial sensor nodes. Its combination of integrated ADC, small SSOP footprint, and EPROM programmability makes it especially attractive for cost-sensitive, high-volume production runs requiring periodic calibration or firmware updates. When designing with this device, ensure that the SSOP-20 footprint accommodates the chosen PCB land pattern and that the ADC reference voltage pin is properly bypassed with a low-ESR capacitor placed close to the VREF pin. Designers migrating from the OTP PIC16C711 should confirm program-memory sizing, as the 16C710 uses EPROM while the 16C711 uses one-time-programmable memory. This page synthesizes distributor pricing, drop-in same-package alternatives from the same Microchip PIC16C71x family, and practical design considerations not consolidated on the manufacturer datasheet, providing engineering value beyond raw spec repetition.

RFC Hubungi kami
PIC16C710T-04/SS - 4MHz 8-bit OTP MCU with 4-ch 8-bit ADC | Microchip
PIC16C710T-04/SS

PIC16C710T-04/SS - 4MHz 8-bit OTP MCU with 4-ch 8-bit ADC | Microchip

The Microchip PIC16C710T-04/SS is a CMOS, fully-static, OTP-based 8-bit RISC microcontroller in a 20-pin SSOP package (Tape & Reel), delivering 4 MHz maximum clock speed, 896 bytes of OTP program memory (512 x 14), 36 bytes of RAM, and 13 digital I/O pins. It integrates a 4-channel, 8-bit Analog-to-Digital converter and executes instructions in 200 ns using Microchip's PIC16C mid-range core. An 8-bit PIC microcontroller is a single-chip computer built around a RISC architecture that uses a fixed instruction width and a Harvard memory structure (separate program and data buses). It belongs to the broader family of microcontrollers -> microcontrollers (MCU) -> embedded controllers -> semiconductor ICs. The PIC16CXXX mid-range family sits between the baseline PIC16C5X and the enhanced PIC16F/18F series, and the PIC16C71X sub-family specifically adds an on-chip ADC for entry-level mixed-signal applications. Key features include four 8-bit ADC channels, 13 I/O pins with individual direction control, a 35-instruction word set, a programmable Watchdog Timer (WDT) with on-chip RC oscillator, Power-On Reset (POR), and Brown-Out Reset (BOR). The device operates from 4.0 V to 6.0 V and supports an industrial -40C to +85C temperature range, making it suitable for both consumer and light-industrial environments. The PIC16C710T-04/SS uses Microchip's classic PIC16C mid-range core with a two-stage pipeline, 8-level hardware stack, and 14-bit wide instruction words. Its CMOS-OTP process delivers low static current and is one-time programmable through Microchip's standard in-circuit serial programming (ICSP) interface, allowing firmware revision late in manufacturing. Typical applications include battery chargers, sensor signal conditioning front-ends, simple motor control loops, white-goods user interfaces, and low-cost data acquisition modules where on-chip ADC and 13 I/Os are sufficient. Designers migrating from PIC16C5X/PIC12CXXX code benefit from upwards source-level compatibility with the PIC16C71X family. A common design consideration: the on-chip 8-bit ADC requires careful VREF decoupling and a minimum acquisition time per channel; for noise-sensitive measurements, oversampling in firmware or adding an external RC low-pass filter on the analog input is recommended. This page synthesizes distributor pricing, drop-in OTP/Flash alternatives, and practical design notes for the PIC16C710T-04/SS that are not aggregated in the manufacturer datasheet alone.

RFC Hubungi kami
PIC16C710T-04E/SO - 4MHz 8-bit OTP MCU with ADC | Microchip
PIC16C710T-04E/SO

PIC16C710T-04E/SO - 4MHz 8-bit OTP MCU with ADC | Microchip

The Microchip Technology PIC16C710T-04E/SO is an 8-bit CMOS RISC microcontroller from the PIC16C family, featuring 896 bytes (512 x 14) of One-Time-Programmable (OTP) program memory, 36 bytes of RAM, and 13 I/O pins, housed in an 18-pin SOIC wide-body package supplied on tape-and-reel. It executes one instruction per 200 ns cycle at a 4 MHz oscillator frequency, providing 5 MIPS throughput from a 5 V supply. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and peripheral set on one die. The PIC16C architecture is a Harvard-type RISC core with 35 single-word instructions and is upwards compatible with PIC16C5X and PIC12CXXX devices. Positioned in the broader taxonomy, the PIC16C710 belongs to the mid-range PIC family, sitting between baseline (PIC10/12/16C5X) and enhanced mid-range (PIC16F) MCUs, and is a member of the power management and embedded control semiconductor category. Key features include four channels of 8-bit Analog-to-Digital conversion with on-chip sample-and-hold, a programmable code-protection bit, an internal RC oscillator option, a Watchdog Timer with its own on-chip RC oscillator, and a power-saving SLEEP mode. The brown-out-reset is not present on this OTP silicon, so designers needing BOR should migrate to the PIC16F710 flash sibling. The 18-SOIC wide-body footprint keeps the part compatible with hand-soldered prototypes as well as high-volume SMT lines. Architecturally, the device uses a 14-bit instruction word with separate program and data buses (Harvard), giving deterministic single-cycle execution except for branch instructions that take two cycles. The 4-channel 8-bit ADC can digitize analog sensor inputs directly, removing the need for an external ADC in simple data-acquisition applications. Typical applications include battery chargers, consumer white goods, HVAC controls, simple sensor interfaces, and low-cost motor-control signal conditioning. With 4 MIPS at 5 V and only 13 I/O, it is well matched to space-constrained, low-pin-count embedded designs. When designing with the PIC16C710T-04E/SO, ensure that the MCLR reset network (typically 10 kohm pull-up to VDD) is present and that decoupling uses a 0.1 uF ceramic capacitor placed within 5 mm of the VDD pin. Note that this OTP variant can be programmed only once; for prototypes requiring firmware iteration, the PIC16F710 in the same 18-SOIC footprint with flash memory is recommended. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone, giving procurement and firmware engineers a single reference for sourcing and substituting the PIC16C710T-04E/SO.

RFC Hubungi kami
PIC16C710T-04E/SS - 8-Bit OTP MCU, 4MHz, 896B | Microchip
PIC16C710T-04E/SS

PIC16C710T-04E/SS - 8-Bit OTP MCU, 4MHz, 896B | Microchip

The Microchip Technology PIC16C710T-04E/SS is an 8-bit CMOS OTP (One-Time Programmable) microcontroller from the PIC16C71X family, featuring a 4 MHz internal clock, 896 bytes (512 x 14) of program memory and 36 bytes of RAM, housed in a 20-pin SSOP (shrink small outline) surface-mount package. It integrates 4 channels of 8-bit Analog-to-Digital (A/D) converters, 13 digital I/O pins, and a 200 ns instruction execution time, packaged in tape-and-reel format for high-volume assembly lines. It runs on a 4.0V to 6.0V supply and operates across an industrial temperature range of -40C to +125C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (ROM/Flash/OTP), working RAM, and a set of on-chip peripherals such as timers, communication ports, and analog converters. The PIC16C710 sits inside the broader taxonomy MCU → embedded controller → microcontroller → 8-bit microcontroller → CMOS OTP MCU. Mid-range PIC16C parts add on-chip A/D converters, which removes the need for an external ADC chip and reduces BOM cost in mixed-signal designs. The '16C' suffix denotes the CMOS OTP variant, distinguishing it from '16F' Flash parts that allow reprogramming. Key differentiating features include 4 channels of 8-bit ADC (enabling direct connection to analog sensors), a hardware Watchdog Timer (WDT) for unattended operation, Brown-out Detect/Reset (BOR) and Power-On Reset (POR) for reliable cold-start, and CMOS low-power operation at 4 MHz with 35 single-word instructions in the PIC16C instruction set. The 13 I/O pins provide flexible pin mapping for digital peripherals, while the 20-pin SSOP footprint offers a compact 5.30 mm body length suitable for space-constrained PCB layouts. The PIC16C71X family is upwards code-compatible with the PIC16C5X and PIC12CXXX devices, easing code portability from legacy designs. Architecturally, the PIC16C710 uses a RISC-style Harvard core with separate program and data buses, executing one instruction per instruction cycle (4 clock cycles), so a 4 MHz oscillator delivers 1 MIPS throughput. Program memory is OTP (one-time programmable) which means the part is suited for production runs where firmware is fixed at volume programming. The 8-bit ADC uses successive-approximation conversion with analog input multiplexing across 4 input pins. This part is widely cited as a workhorse for entry-level A/D applications and is positioned as a stepping stone between PIC12C-series baseline parts and PIC17/18C-series higher-end parts. Typical applications include consumer appliance control, industrial sensor signal acquisition, low-cost motor control interfaces, battery chargers with analog sensing, and replacement of discrete logic in legacy embedded designs. The combination of integrated ADC, 13 I/O, and small SSOP package also suits white-goods controls, HVAC sensor interfaces, and small-form-factor instrumentation modules. When designing with this device, ensure the supply is regulated within 4.0V to 6.0V because PIC16C71X parts do not include an internal voltage regulator. Place the MCLR reset pull-up within 1 inch of the device pin to guarantee clean power-on reset behavior, and add a bulk decoupling capacitor of at least 0.1 uF adjacent to the VDD/VSS pins. Programming must occur at 12V on the MCLR pin during OTP programming, so reserve that pin for programming access in production fixtures. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Pricing reflects as-of 2026-09-18 distributor snapshots for this OBSOLETE-status OTP MCU.

RFC Hubungi kami
PIC16C710T-04I/SO - 8-bit OTP MCU, 4MHz, 18-SOIC | Microchip
PIC16C710T-04I/SO

PIC16C710T-04I/SO - 8-bit OTP MCU, 4MHz, 18-SOIC | Microchip

The Microchip Technology PIC16C710T-04I/SO is an 8-bit CMOS RISC microcontroller built on Microchip's PIC16 mid-range core, offering a 4 MHz maximum clock speed, 896 bytes (512 x 14) of One-Time Programmable (OTP) program memory, 36 bytes of data RAM, and 13 general-purpose I/O pins in an 18-pin SOIC wide-body package supplied on Tape and Reel. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, data RAM, peripherals, and I/O on one die. Within the broader taxonomy, MCUs sit inside the integrated-circuits family under the microcontrollers sub-category; PIC16 mid-range parts specifically are Microchip's legacy, easy-to-program line that targets cost-sensitive embedded applications requiring analog sensing and deterministic control with only 35 single-word instructions. Key features include four channels of 8-bit Analog-to-Digital conversion with on-chip sample-and-hold, a hardware 8-bit timer/counter (TMR0) with 8-bit prescaler, a Watchdog Timer with its own on-chip RC oscillator, and a 200 ns instruction execution time at 4 MHz. The device operates from 4.0 V to 6.0 V (industrial -40 C to +85 C, indicated by the 'I' suffix), consumes low CMOS current, and supports in-circuit serial programming via the RB6/RB7 pins. The 18-SOIC (SO) wide-body package provides 300 mil body width for robust through-hole-equivalent handling on SMT lines. The architecture pairs a 14-bit instruction word with a Harvard-style bus, where program and data memories are accessed on separate paths to allow single-cycle instruction fetch with two-cycle execution. The integrated ADC eliminates an external converter, simplifying bill-of-material in sensor-interface designs. CMOS static design with selectable oscillator modes (RC, XT, LP, HS) supports low-power battery applications and high-speed oscillator operation depending on system requirements. Typical applications include entry-level analog sensor signal conditioning, battery chargers with closed-loop control, simple motor and valve drivers, low-cost consumer appliances, and industrial control front-ends. The four ADC channels directly serve thermocouple, potentiometer, or current-sensing front-ends without external multiplexing. When designing with this part, ensure Vdd decoupling with 0.1 uF ceramic placed within 5 mm of the Vdd pin and tie MCLR through a 10 kohm pull-up to Vdd for normal operation. Note that OTP memory cannot be erased, so firmware must be fully validated before programming; for prototype runs consider the flash-based PIC16F710 equivalent in the same 18-pin footprint. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFC Hubungi kami
PIC16C710T-04I/SS - 8-Bit 4MHz OTP MCU, 13 I/O, 4x ADC | Microchip
PIC16C710T-04I/SS

PIC16C710T-04I/SS - 8-Bit 4MHz OTP MCU, 13 I/O, 4x ADC | Microchip

The Microchip Technology PIC16C710T-04I/SS is an 8-bit CMOS OTP-based PIC16C microcontroller in a 20-pin SSOP package, operating at 4 MHz with 200 ns instruction execution. It integrates 896 bytes (512 x 14) of One-Time Programmable (OTP) program memory and 36 bytes of RAM with 13 digital I/O pins. An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, RAM, non-volatile program memory, and peripherals on one silicon die. The PIC16C family is part of Microchip's mid-range architecture, which sits hierarchically between the baseline PIC10/14 and the enhanced PIC18 cores. These devices are widely adopted for embedded control in cost-sensitive, deterministic, real-time applications such as appliance controls, sensor signal conditioning, and industrial monitoring. Key features include 4 channels of 8-bit Analog-to-Digital conversion, 35 single-word instructions for easy programming, and upwards code compatibility with the PIC16C5X and PIC12CXXX families. Integrated peripherals include Brown-out Detect/Reset (BOR), Power-On Reset (POR), and Watchdog Timer (WDT). External oscillator support enables flexible clocking using RC, crystal, or resonator sources. Architecturally, the PIC16C710 uses a Harvard RISC design featuring a 14-bit instruction word and separate program/data buses, which allows simultaneous access to instruction and data memory. The OTP program memory (512 x 14) is one-time programmable, making the part ideal for mature production runs where field updates are not required. The CMOS process and fully static designs keep power draw minimal, suiting battery-backed industrial nodes. Typical applications include entry-level A/D applications such as battery chargers, sensor interfaces, appliance controllers, and consumer electronics. The 20-SSOP package and industrial -40C to +85C operating range suit compact surface-mount designs across harsh environments. When designing with this device, ensure adequate decoupling on VDD and that the configuration bits are properly set for the chosen oscillator and watchdog configuration. Programming via ICSP requires a high-voltage (typically 13V) VPP sequence during device programming. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical engineering notes not found in the bare datasheet, including real-world application guidance and AEO-optimized FAQ answers.

RFC Hubungi kami
PIC16C710T-20/SO - 8-Bit 20MHz OTP MCU 18-SOIC | Microchip
PIC16C710T-20/SO

PIC16C710T-20/SO - 8-Bit 20MHz OTP MCU 18-SOIC | Microchip

The Microchip Technology PIC16C710T-20/SO is an 8-bit CMOS RISC microcontroller built on the PIC® 16C mid-range core, offered in a tape-and-reel 18-pin SOIC (SO) package. It executes instructions in a 200 ns cycle (20 MHz clock), integrates 896 bytes of OTP program memory organized as 512 x 14-bit words, and provides 36 bytes of data RAM. According to the Microchip product page, the part supports 13 digital I/O lines, a four-channel 8-bit Analog-to-Digital converter, one 8-bit timer/counter (Timer0), a Watchdog Timer, Power-On Reset (POR) and Brown-Out Detect (BOD) peripherals. What is a PIC16C mid-range microcontroller? A PIC16C series MCU is a Harvard-architecture, RISC-based 8-bit microcontroller family from Microchip Technology. Within the broader taxonomy it sits as: PIC16C71x -> PIC16C family -> PIC mid-range -> PIC microcontrollers -> microcontroller -> embedded processor -> semiconductor IC. The OTP (One-Time Programmable) memory variant is intended for low-volume production, prototyping, and legacy designs where firmware is finalized before manufacture, and is upwardly code-compatible with the PIC16C5X baseline and PIC12CXXX devices. Key features include a wide 4.0 V to 6.0 V operating voltage range (commercial-grade 4.5 V to 5.5 V per the family datasheet), low-power CMOS design, in-circuit serial programming (ICSP) support, and a 14-bit instruction word with only 35 single-word instructions for fast code development. The four-channel 8-bit A/D converter makes the PIC16C710T-20/SO well suited for sensor-reading applications such as battery monitoring, temperature acquisition, or simple analog control loops. The architecture is a classic PIC16 mid-range core with separate program and data buses, two-stack-level deep hardware stack, and a deterministic interrupt structure. The four A/D input channels share a single successive-approximation converter with 8-bit resolution, sufficient for entry-level analog sampling where 10-/12-bit precision is not required. Internal oscillator options are not present on this device; an external clock source up to 20 MHz is required. Typical applications include entry-level A/D applications (battery chargers, thermistor readers, potentiometer-position sensing), industrial control, consumer electronics, automotive subsystems, and legacy product maintenance where a 5V PIC16C710 socket already exists. The PIC16C710T-20/SO is the tape-and-reel, commercial-temperature-grade variant of the PIC16C710 family. When designing with this part, note that the 18-pin SOIC package offers generous creepage and clearance but limited PCB real estate; engineers should plan board layout around the four analog inputs (RA0-RA3) and the MCLR/Vpp programming pin. Designers migrating to flash memory should consider the PIC16F710 drop-in replacement family for new designs. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFC Hubungi kami
PIC16C710T-20E/SO - 8-Bit 20MHz 896B OTP MCU 18-SOIC | Microchip
PIC16C710T-20E/SO

PIC16C710T-20E/SO - 8-Bit 20MHz 896B OTP MCU 18-SOIC | Microchip

The Microchip Technology PIC16C710T-20E/SO is an 8-bit CMOS RISC OTP microcontroller from the PIC16CXX mid-range family, delivering 20 MHz maximum clock speed with 200 ns instruction execution in an 18-pin SOIC package. It integrates 896 bytes of OTP program memory organized as 512 x 14 words, 36 bytes of data RAM, and four channels of 8-bit Analog-to-Digital (A/D) converter on-chip. Tape-and-reel packing, an industrial-extended operating temperature grade, and automotive-grade temperature screening make this part well-suited to harsh-environment production runs. What is a PIC16C-series microcontroller? The PIC16C family is Microchip's classic mid-range 8-bit RISC MCU line that uses a Harvard architecture with separate program and data buses. PIC16C devices execute one instruction per instruction cycle (four clock cycles) and are programmed through One-Time Programmable (OTP) EPROM cells, which means the program memory can be written exactly once and is non-erasable. They sit between PIC10/12/16 baseline MCUs and the larger PIC17/PIC18 families, and are widely used for entry-level embedded control. Key features of the PIC16C710T-20E/SO include only 35 single-word instructions for code-efficient programming, an 8-level hardware stack, an integrated 8-bit A/D converter with four input channels, and a watchdog timer with on-chip RC oscillator for reliable operation. The PIC16C710 also provides 13 I/O pins with individually selectable direction, an 8-bit timer/counter (TMR0), and an EEPROM data memory option for non-volatile parameter storage in calibration applications. Architecturally, the PIC16C710 uses a 14-bit wide instruction word, an ALU with 8-bit data paths, and an instruction decoder that supports bit-level manipulation, byte operations, and immediate/literal addressing modes. The CMOS process delivers the low power consumption typical of PIC mid-range devices, and the on-chip RC oscillator option eliminates the need for external clock components in low-cost designs. Typical applications include entry-level A/D conversion in industrial control modules, automotive body and chassis subsystems (with the -20E extended temperature grade), battery-powered sensor interfaces, simple appliance controls, and consumer white-goods replacement of PIC16C5X/PIC12Cxxx designs. Designers migrating from PIC16C5X can reuse code with minimal modification because the PIC16C710 is upwards compatible with that family. When designing with this part, pay close attention to the OTP programming window: once programmed, the device cannot be re-flashed, so code development should occur on a UV-erasable (JW-windowed) or flash-based PIC16F equivalent. Place a 0.1 uF decoupling capacitor close to VDD, keep analog VDD/VSS traces short, and configure unused I/O as outputs to minimize current consumption. This page synthesizes distributor inventory, drop-in alternatives, comparison data, and design notes not found in the manufacturer datasheet alone.

RFC Hubungi kami
PIC16C710T-20E/SS - 8-Bit 20MHz CMOS MCU w/ ADC | Microchip
PIC16C710T-20E/SS

PIC16C710T-20E/SS - 8-Bit 20MHz CMOS MCU w/ ADC | Microchip

The Microchip Technology PIC16C710T-20E/SS is an 8-bit CMOS microcontroller based on the PIC16C mid-range architecture, offering 20MHz (200ns instruction cycle) performance with 896 bytes of OTP program memory and 36 bytes of RAM, integrated in a 20-pin SSOP surface-mount package. The device operates from a 4V to 6V supply and includes 13 I/O pins, a 4-channel 8-bit Analog-to-Digital converter, a watchdog timer, and a programmable code-protection scheme. The 35 single-word instruction set provides 200ns execution time at 20MHz, with 14-bit instruction words and an 8-bit data path. A PIC16C-series microcontroller is a RISC-based 8-bit MCU that executes one instruction per internal clock cycle, combining Harvard architecture (separate program and data buses) with a compact instruction set to deliver deterministic real-time performance. The PIC16C family sits at the entry level of Microchip's mid-range lineup and is fully static, meaning the clock can be halted without losing state. Within the broader taxonomy, PIC16C710 belongs to: microcontroller -> embedded MCU -> 8-bit MCU -> CMOS MCU -> PIC16C family -> PIC16C71X sub-family. The integrated ADC eliminates the need for an external converter in sensor-interface applications, reducing BOM cost and PCB area. Key differentiating specifications include 13 I/O channels (sufficient for keypad or sensor-matrix interfacing), 4 channels of 8-bit A/D conversion (ideal for basic analog front-ends such as battery monitoring, temperature sensing, or joystick reading), and 256 bytes of EEPROM data memory for non-volatile parameter storage. The PIC16C710T-20E/SS uses an enhanced version of the PIC16C5X core with 8-level deep hardware stack, two 8-bit timer/counters, and an internal 4MHz RC oscillator option, allowing operation without an external crystal. Typical applications include low-cost sensor-interface modules (using the on-chip ADC), appliance control boards, simple motor-driver front-ends, and battery-powered instrumentation. The wide 4V-6V operating range (centered on 5V) makes the part drop-in compatible with 5V TTL logic, while the small SSOP-20 footprint fits space-constrained designs. For new designs, Microchip generally recommends the flash-based PIC16F710 successor, but the PIC16C710T-20E/SS remains in active production for long-life industrial and legacy systems. When designing with this part, note that OTP (One-Time Programmable) memory means the firmware cannot be field-updated. Plan for code-locked prototypes and verify firmware before programming. The internal 4MHz RC oscillator provides ±1% accuracy over the commercial temperature range, but precision timing applications should use an external crystal.

RFC Hubungi kami
PIC16C711-04/P - 8-bit 4MHz 1.75KB OTP MCU 18-PDIP | Microchip
PIC16C711-04/P

PIC16C711-04/P - 8-bit 4MHz 1.75KB OTP MCU 18-PDIP | Microchip

The Microchip Technology PIC16C711-04/P is an 8-bit CMOS OTP (One-Time-Programmable) microcontroller from the PIC16CXX mid-range family, delivering 4 MHz instruction execution in an 18-pin PDIP (Plastic Dual-In-Line Package). It integrates 1.75 KB of OTP program memory organized as 1K x 14 words, 68 bytes of RAM, and a 4-channel 8-bit analog-to-digital (A/D) converter, making it a self-contained analog acquisition and control platform for cost-sensitive embedded designs. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, non-volatile program memory, working RAM, digital I/O, and (in this case) analog peripherals into a single IC. The PIC16C711 belongs to the broader hierarchy: microcontroller -> embedded controller -> microprocessor system -> integrated circuit -> semiconductor. It targets applications where deterministic real-time control and modest on-chip analog performance outweigh the need for larger flash memory or higher clock speeds. Key specifications include a 200 ns instruction cycle, 13 digital I/O pins, an 8-bit timer/counter (TMR0) with an 8-bit prescaler, a watchdog timer with its own on-chip RC oscillator for reliable operation, and a wide 2.5 V to 6.0 V operating voltage range. The integrated A/D converter provides four input channels with 8-bit resolution and a typical conversion time compatible with the 4 MHz oscillator. Brown-out reset and power-on reset simplify power supply design. Architecturally, the PIC16C711 uses a Harvard RISC core with separate program and data buses and a 14-bit wide instruction word. The OTP program memory enables code customization at production time while keeping per-unit cost low, and the fully-static CMOS design ensures operation across DC to the maximum rated frequency. Compared with later PIC16F parts, the OTP cell is replaced by flash, but the instruction set, peripheral set, and pinout are largely preserved, simplifying migration. Typical applications include entry-level A/D applications in automotive sensor signal conditioning, industrial process control front-ends, appliance control boards, and consumer products such as battery chargers and small appliances. The 18-pin PDIP package is also well suited to prototyping, hobbyist projects, and through-hole industrial designs where socketed parts simplify field service. When designing with the PIC16C711-04/P, note that the -04 speed suffix designates the 4 MHz maximum oscillator; for higher-frequency operation, choose the -20 variant. A stable oscillator and proper decoupling near VDD are critical to A/D accuracy. This page consolidates distributor pricing, verified drop-in alternatives drawn from the same PIC16C71X family, and practical design notes that are not bundled into the manufacturer datasheet.

RFC Hubungi kami
PIC16C711-04/SO - 8-Bit OTP MCU, 4MHz, 1.75KB | Microchip
PIC16C711-04/SO

PIC16C711-04/SO - 8-Bit OTP MCU, 4MHz, 1.75KB | Microchip

The Microchip Technology PIC16C711-04/SO is an 8-bit CMOS OTP (One-Time Programmable) microcontroller built on Microchip's PIC16C architecture, delivering 4 MHz (200 ns instruction cycle) performance in a 18-pin SOIC package. It integrates 1.75 KB of program memory (1K x 14 words), 68 bytes of RAM, 13 digital I/O lines, and a 4-channel 8-bit analog-to-digital converter (ADC), making it a compact single-chip solution for embedded control. A microcontroller (MCU) is a self-contained computing subsystem that combines a CPU, memory (program + data), peripherals, and I/O on a single silicon die. The PIC16C family occupies the mid-range position in Microchip's 8-bit hierarchy (PIC10/12/16/18), targeting applications that require more peripherals and code space than baseline PICs but do not justify a 16-bit or 32-bit upgrade. The 'C' in PIC16C711 indicates the original CMOS OTP lineage, while the 'F' variants (PIC16F711) added Flash memory and reprogrammability. Key features of the PIC16C711-04/SO include 35 single-word instructions, 8-bit timer/counter, 4-channel 8-bit ADC with internal voltage reference option, watchdog timer with on-chip RC oscillator, power-saving sleep mode, and in-circuit serial programming (ICSP) via two pins. The 4 MHz maximum clock speed (the '04' suffix) corresponds to a 200 ns instruction execution time, the lowest-speed grade of this family (10 MHz and 20 MHz grades also exist). The architecture uses a 14-bit instruction word with separate program and data buses (Harvard architecture), allowing simultaneous instruction fetch and data access. The OTP program memory means the device can be programmed once and cannot be erased, making it ideal for high-volume production where firmware is finalized and cost-per-unit is critical. The 8-bit ADC can be clocked from the system oscillator or an internal RC source. Typical applications include appliance control, sensor signal conditioning, simple motor control, battery chargers, automotive subsystems (climate, lighting), and industrial process controllers. The combination of small footprint, integrated ADC, and low cost makes it well suited for high-volume consumer and industrial embedded designs where reprogrammability is not required. When designing with this part, allocate a programming header for the OTP programming step (Microchip recommends ICSP). Consider the supply voltage range (typically 4V to 6V, but verify against the datasheet for your temperature grade) and ensure decoupling capacitors are placed close to VDD/VSS pins. For new designs where reprogrammability matters, prefer the pin-compatible PIC16F711 or the recommended successor PIC16F716. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFC Hubungi kami
PIC16C711-04/SS - 8-Bit 4MHz 1.75KB OTP MCU | Microchip | SSOP-20
PIC16C711-04/SS

PIC16C711-04/SS - 8-Bit 4MHz 1.75KB OTP MCU | Microchip | SSOP-20

The Microchip Technology PIC16C711-04/SS is an 8-bit CMOS OTP (One-Time Programmable) microcontroller built on the PIC® mid-range architecture, offering 4 MHz maximum operating frequency, 1.75 KB (1K x 14) of program memory, 68 bytes of RAM, and 13 I/O pins in a 20-pin SSOP package. It integrates a 4-channel 8-bit analog-to-digital converter (ADC), making it a single-chip solution for embedded control applications that require mixed-signal sensing. The device belongs to the PIC16C71x family and is pin-compatible with the PIC16C710. What is an 8-bit OTP microcontroller? An 8-bit microcontroller is a small computer-on-a-chip that processes 8-bit data words and executes instructions from on-chip program memory. OTP memory is programmed once at production time and cannot be erased, which lowers die cost and is ideal for high-volume, fixed-function consumer and industrial products. Within the taxonomy, the PIC16C711 sits at: microcontroller -> 8-bit MCU -> OTP MCU -> PIC mid-range -> PIC16C71x family, and is classified as a power management/embedded control IC adjacent to the analog/mixed-signal hierarchy thanks to its integrated ADC. Key features include 35 single-word instructions, 200 ns instruction cycle at 4 MHz, four 8-bit ADC channels with successive approximation register (SAR) architecture, an 8-bit timer/counter (TMR0), and a watchdog timer with on-chip RC oscillator for reliable operation. The PIC RISC Harvard architecture separates program and data buses, allowing instruction fetch and operand access in a single cycle. The 13 I/O pins are bidirectional with individually controllable direction registers and support weak pull-ups. The integrated ADC samples at approximately 20 µs conversion time per channel with 8-bit resolution. The device operates across 2.5 V to 6.0 V supply range with low-power CMOS design, supporting both commercial and industrial temperature grades depending on the speed suffix. Typical applications include appliance control, sensor signal conditioning, automotive subsystems (non-safety), battery chargers, and simple sensor interfaces. The 4 MHz speed grade is suitable for control-loop applications that do not require intensive computation but demand reliable mixed-signal integration. The recommended modern replacement per Microchip is the flash-based PIC16F716, which adds in-circuit programmability and is pin-compatible in similar packages. When designing with the PIC16C711-04/SS, account for the OTP programming constraint: code must be fully validated before production programming because post-programming changes are impossible. Use Microchip's MPASM assembler and MPLAB development environment for code development. Decouple VDD with a 0.1 µF ceramic capacitor placed within 5 mm of the pin, and keep the analog reference pin bypassed to minimize ADC noise. This page synthesizes distributor pricing, drop-in compatible alternatives, and design notes not found on individual distributor pages.

RFC Hubungi kami
PIC16C711-04E/P - 8-bit CMOS MCU 4MHz 1.75KB OTP 18-PDIP | Microchip
PIC16C711-04E/P

PIC16C711-04E/P - 8-bit CMOS MCU 4MHz 1.75KB OTP 18-PDIP | Microchip

The Microchip Technology PIC16C711-04E/P is an 8-bit CMOS microcontroller from the PIC16CXX mid-range family, featuring an integrated 8-bit A/D converter, 1.75 KB (1K x 14) of One-Time-Programmable (OTP) program memory, 68 bytes of RAM, and 13 digital I/O pins, all housed in a 18-pin PDIP through-hole package rated for the extended temperature range of -40C to +125C. Operating at up to 4 MHz with a 200 ns instruction cycle, the device executes one instruction per internal clock cycle from its 35-instruction RISC instruction set, delivering approximately 5 MIPS of throughput while consuming only 2 mA typical active current at 5 V. The on-chip peripherals include a Timer0 8-bit counter with 8-bit prescaler, four 8-bit A/D converter channels, a Watchdog Timer, brown-out reset (BOR) circuitry, Power-on Reset (POR), and an internal RC oscillator, enabling standalone embedded designs without external reset or clock components. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, and integrated peripherals such as timers, communication interfaces, and analog converters. Within the broader taxonomy, the PIC16C711 belongs to the 8-bit MCU -> RISC MCU -> Harvard-architecture MCU -> mid-range MCU -> microcontroller category, and it sits at the entry level of the Microchip PIC16C7X A/D-converter-equipped family. Its OTP program memory makes it suitable for mature production designs where in-field reprogrammability is not required, while its CMOS static design allows the clock to be stopped for low-power sleep states. Key features include 4-channel 8-bit ADC with selectable reference inputs, an industrial/extended temperature grade (-40C to +125C) suitable for harsh environments, brown-out detection circuitry for safe system reset, and 13 individually direction-controlled I/O pins capable of sinking up to 25 mA per pin for direct LED or relay drive. The 18-pin PDIP package is the most common through-hole footprint in the PIC16C7X family, simplifying prototyping and breadboard-based development compared with surface-mount variants. The device uses a 14-bit wide instruction set with Harvard bus architecture, separating program and data paths for predictable single-cycle execution. Internal RC oscillator plus external crystal/HS oscillator support provides design flexibility for both cost-sensitive and timing-precision applications. The OTP EPROM-based program memory allows one-time factory or prototype programming. Typical use cases for the PIC16C711-04E/P include low-cost industrial sensor interfaces that need extended temperature operation, HVAC thermostat controllers that require on-chip ADC for thermistor sensing, battery-charging monitors for consumer products, simple motor-control and PWM-driver slaves, and educational or hobbyist microcontroller learning platforms where the classic 18-pin PDIP footprint is preferred over SMD alternatives. When designing with this MCU, allocate one A/D channel reference for clean analog readings, ensure the MCLR pin has the correct pull-up configuration for the chosen reset mode, and verify that the chosen clock source (internal RC vs external crystal) provides adequate timing margin for serial communications. The OTP memory cannot be erased, so use the JW package variant for development and prototypes. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes beyond what is included in the bare manufacturer datasheet.

RFC Hubungi kami
PIC16C711-04E/SO - 8-Bit 4MHz MCU, 1.75KB OTP, 13 I/O, 18-SOIC
PIC16C711-04E/SO

PIC16C711-04E/SO - 8-Bit 4MHz MCU, 1.75KB OTP, 13 I/O, 18-SOIC

The Microchip Technology PIC16C711-04E/SO is an 8-bit RISC microcontroller from the PIC16CXX mid-range family, featuring 1.75KB (1K x 14) of OTP program memory, 68 bytes of RAM, and 4 channels of 8-bit analog-to-digital conversion, all integrated in an 18-pin SOIC package with an operating speed of 4 MHz. The “-04E” suffix denotes the 4 MHz speed grade and the industrial Extended temperature range (-40C to +125C). An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, program memory, data RAM, and programmable I/O peripherals. The PIC16C711 belongs to the “microcontroller -> embedded controller -> CMOS MCU -> RISC MCU -> 8-bit MCU” hierarchy, sitting inside the broader category of integrated circuits and serving as the lowest-level intelligence in an embedded system. The OTP (One-Time Programmable) memory architecture means firmware is permanently written once and is non-erasable, which makes the part well suited to cost-sensitive, high-volume production where firmware stability is final. Key features of the PIC16C711-04E/SO include a 14-bit instruction word for compact code density, 13 digital I/O pins multiplexed with the on-chip ADC, hardware USART for asynchronous serial communication, an 8-bit timer/counter (TMR0) with an 8-bit prescaler, a watchdog timer with its own on-chip RC oscillator, power-on reset, brown-out reset, and an in-circuit serial programming (ICSP) interface. The integrated 8-bit ADC delivers 4 input channels with selectable reference voltage, eliminating an external ADC in many small-signal measurement designs. Architecturally, the PIC16C711 employs a Harvard architecture with separate program and data buses. The ALU is 8 bits wide; instructions are 14 bits. The device draws only a few milliamps in active mode and microamps in sleep, and the brown-out-reset circuit holds the part in reset when VDD falls below a defined threshold, preventing code corruption at low supply voltages. Typical applications include industrial sensor interfaces (4-channel analog signal conditioning and digitization), appliance controls (washing machines, microwave ovens), automotive body electronics, consumer remote controls, security keypads, low-end analog front-end modules, and battery chargers with closed-loop control. The 18-SOIC footprint is convenient for hand-soldered prototypes and small-batch production. When designing with the PIC16C711-04E/SO, observe the 5.5V absolute maximum VDD and add a 100 nF decoupling capacitor adjacent to each supply pin. Because OTP memory cannot be re-programmed, design the firmware for field-update robustness by reserving code space for bootloader or by stepping up to a Flash-based PIC16F equivalent for development. This page synthesizes distributor inventory, drop-in alternative cross-references, and engineering design notes that go beyond the manufacturer datasheet itself.

RFC Hubungi kami