Mikropengawal

Produk (20,000+)

PIC16F18445-E/GZ - 8-bit 32MHz 14KB Flash XLP MCU | Microchip
PIC16F18445-E/GZ

PIC16F18445-E/GZ - 8-bit 32MHz 14KB Flash XLP MCU | Microchip

The Microchip Technology PIC16F18445-E/GZ is an 8-bit PIC microcontroller from the PIC16(L)F184xx family with eXtreme Low-Power (XLP) technology, Functional Safety (FuSa) features, and Core Independent Peripherals (CIPs). It operates at up to 32 MHz, integrates 14 KB (8K x 14) of Flash program memory, 1 KB of RAM, and is housed in a 20-pin UQFN (4x4 mm) package with exposed pad. What is an 8-bit PIC microcontroller? An 8-bit MCU is a microcontroller whose internal data path, ALU and registers are 8 bits wide; the PIC architecture (Peripheral Interface Controller) is a Harvard RISC design from Microchip widely used in low-power and cost-sensitive embedded designs. The PIC16F18445 sits in the hierarchy: MCU -> 8-bit MCU -> PIC16 family -> PIC16F184xx sub-family -> functional-safety / XLP line, combining Core Independent Peripherals (CIPs), high-resolution analog, and eXtreme Low-Power modes for general-purpose and battery-powered applications. Key features include a 12-bit Analog-to-Digital Converter with Computation (ADCC), a 5-bit/8-bit Digital-to-Analog Converter (DAC), two PWMs, a Complementary Waveform Generator (CWG), a comparator, EUSART, SPI, and I2C communication peripherals. The device is rated for the extended -40C to +125C industrial temperature range (the trailing E in the part number indicates the extended industrial grade) and offers multiple low-power sleep modes with nanoWatt XLP technology for energy harvesting and battery applications. The PIC16F18445-E/GZ uses the enhanced mid-range PIC16 core with 49 instructions, hardware multiply, and a 16-level hardware stack. On-chip peripherals such as the Peripheral Pin Select (PPS) allow flexible signal routing, while the Configurable Logic Cell (CLC) and Signal Measurement Timer (SMT) provide hardware-level state-machine and timing functions without CPU intervention. These CIPs reduce firmware complexity and deterministic latency. Typical applications include low-power IoT sensor nodes, consumer appliance controls, battery-powered instruments, LED lighting controllers, functional-safety sensor interfaces, and small home-automation devices. The combination of ADCC + DAC + CWG makes the part particularly suitable for closed-loop control of LEDs, fans, and small motor drivers. When designing with the PIC16F18445-E/GZ, ensure the exposed thermal pad is soldered to the PCB ground plane for thermal dissipation and mechanical reliability, and use MPLAB X IDE with XC8 compiler for firmware development. Programming is supported through MPLAB PICkit, ICD, or Curiosity development toolchains. This page synthesizes distributor pricing, same-package drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFC Hubungi kami
PIC16F18445-E/P - 14KB Flash 8-bit MCU, 32MHz, 20-PDIP | Microchip
PIC16F18445-E/P

PIC16F18445-E/P - 14KB Flash 8-bit MCU, 32MHz, 20-PDIP | Microchip

The Microchip Technology PIC16F18445-E/P is an 8-bit PIC16 microcontroller from the PIC16(L)F184xx family with 14KB of Flash, 1KB of RAM, and a 32MHz internal oscillator, housed in a 20-pin PDIP through-hole package. It features eXtreme Low-Power (XLP) technology and Functional Safety (FuSa) capabilities, making it suitable for safety-critical and battery-powered applications. The device operates over a wide 1.8V to 5.5V voltage range. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, memory, and peripherals into a single IC. The 8-bit CPU architecture processes data 8 bits at a time, which is well suited for cost-sensitive, low-power embedded control. Within the broader taxonomy, an MCU belongs to: microcontroller -> embedded processor -> semiconductor -> integrated circuit. The PIC16F18445 sits at the intersection of low-power (XLP) and functional-safety design, making it ideal for general-purpose and safety-critical systems. Key features of the PIC16F18445-E/P include Core Independent Peripherals (CIPs) such as Complementary Waveform Generator (CWG), Configurable Logic Cells (CLC), 12-bit ADCC with computation, 5-bit DAC, and two PWMs. Communication peripherals include EUSART, SPI, and I2C, providing flexible connectivity. The device includes a 32MHz internal oscillator and supports up to 32kHz operation for low-power modes. It is rated for the enhanced (-E) temperature range of -40C to +125C, suitable for industrial environments. The PIC16F18445-E/P utilizes Microchip's enhanced mid-range 8-bit core with a 14-bit instruction set, providing 8K x 14 words of program memory. The integrated XLP technology enables nanoWatt sleep modes with current consumption below 50 nA in deep sleep. The 12-bit ADC with computation automates averaging, filtering, and threshold comparison, reducing firmware overhead and improving real-time responsiveness. Typical applications include industrial sensor nodes, battery-powered IoT devices, home automation controllers, automotive body electronics (non-safety), LED lighting controllers, and low-power remote controls. The combination of XLP, Functional Safety, and rich analog peripherals allows a single device to replace multiple discrete components. When designing with this MCU, ensure proper decoupling (100nF + 10uF) near the VDD pin and use the ICSP programming interface for in-circuit firmware updates. The -E temperature grade supports industrial operation but is not AEC-Q100 qualified; choose the -EQ automotive variant for vehicle applications. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

RFC Hubungi kami
PIC16F18445-E/SS - 14KB Flash 8-bit MCU 32MHz SSOP-20 | Microchip
PIC16F18445-E/SS

PIC16F18445-E/SS - 14KB Flash 8-bit MCU 32MHz SSOP-20 | Microchip

The Microchip Technology PIC16F18445-E/SS is an 8-bit RISC PIC16 XLP microcontroller IC featuring 32 MHz CPU speed, 14 KB (8K x 14 words) of FLASH program memory and 1 KB of SRAM data RAM in a 20-pin SSOP package. According to the Microchip product family description, the PIC16(L)F184xx family adds high-resolution analog, Core Independent Peripherals (CIPs) and communication interfaces alongside eXtreme Low-Power (XLP) technology. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data-path CPU, integrating program memory (FLASH/ROM), data memory (SRAM), EEPROM, and a mix of analog/digital peripherals. Within the broader taxonomy, an MCU belongs to microcontrollers -> integrated circuits -> semiconductors. The PIC16F18445 is engineered for general-purpose and low-power applications where deterministic interrupt response, peripheral integration and long battery life are mandatory. Key differentiating features include 14 KB self-programmable FLASH, 256 bytes of EEPROM, 1 KB SRAM, a 12-bit ADC with Computation (ADCC), a 5-bit DAC, two comparators with 5-bit DAC reference, two PWM modules with Complementary Waveform Generator (CWG), an Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART) and SPI/I2C. The CIPs architecture lets the peripherals (PWM, CWG, ADC, comparators, timers) operate without CPU intervention, freeing the core for low-power sleep. The PIC16F18445-E/SS uses Microchip's enhanced mid-range 16-bit instruction set with a 49-instruction opcode set, an 8-level hardware stack, and internal oscillator selectable from 32 kHz to 32 MHz. Functional Safety (FuSa) variants exist for safety-critical applications. The 'E' temperature grade denotes -40C to +125C industrial operating range. Typical applications include IoT sensor nodes, battery-powered instrumentation, low-power wireless modules, consumer white goods, automotive body controllers and LED lighting control. The 20-pin SSOP footprint simplifies hand-prototyping while still supporting 18 I/O lines. Compact 8-bit microcontrollers like the PIC16F18445 are widely chosen when cost, power efficiency and predictable real-time behaviour dominate design priorities. When designing with this part, place a 0.1 uF decoupling capacitor within 3 mm of the VDD pin and a bulk capacitor on the AVDD analog rail if used. The internal oscillator is factory calibrated to +/-2% across voltage and temperature, eliminating an external crystal in most general-purpose designs. For RF-sensitive or USB-class timing accuracy, route an external 32.768 kHz crystal to the SOSC pins instead. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, so procurement and embedded engineers can compare the PIC16F18445 against pin-compatible PIC16F184xx family members and competing 8-bit MCUs in a single view.

RFC Hubungi kami
PIC16F18445-E/SSVAO - 14KB Flash 8-bit MCU AEC-Q100 | Microchip
PIC16F18445-E/SSVAO

PIC16F18445-E/SSVAO - 14KB Flash 8-bit MCU AEC-Q100 | Microchip

The Microchip Technology PIC16F18445-E/SSVAO is an 8-bit RISC microcontroller from the PIC16F184xx family featuring 14 KB of Flash program memory, 1 KB of SRAM, and 256 bytes of data EEPROM in a 20-pin SSOP package. The /VAO suffix indicates AEC-Q100 automotive qualification, an extended operating temperature range of -40C to +125C, and automotive-grade production flow. The device integrates a 32 MHz internal oscillator, a 12-bit ADC with Computation (ADCC), a 5-bit DAC, two comparators, two PWM modules, a Complementary Waveform Generator (CWG), EUSART, SPI, and I2C communication peripherals. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile data memory (SRAM), EEPROM for parameter storage, and a rich set of on-chip peripherals. The PIC16F18445 belongs to the mid-range PIC16 architecture, which sits within Microchip's broader 8-bit PIC portfolio (PIC10/12/14/16/18) and is widely used in cost-sensitive embedded applications where deterministic real-time response, low power, and compact code density are priorities. Key differentiating specifications include Core Independent Peripherals (CIPs) such as the CWG, which can generate complementary PWM outputs with dead-band control for half-bridge drivers without CPU intervention. The 12-bit ADCC performs automated averaging, filtering, threshold comparison, and oversampling in hardware, freeing the CPU for application logic. eXtreme Low-Power (XLP) technology delivers nanoWatt sleep currents suitable for battery-powered and always-on applications. Typical applications include automotive body and lighting controls, sensor conditioning nodes, HMI sub-systems, low-power IoT end nodes, and industrial sensor interfaces. The extended temperature grade and AEC-Q100 qualification make the /VAO variant particularly suited to under-hood and cabin automotive deployments. Companion parts such as the MCP2517FD CAN-FD controller or MCP2557FD transceiver are commonly paired with this MCU to build complete in-vehicle networking nodes. When designing with this device, pay attention to the SSOP-20 thermal dissipation limit at high ambient temperatures, ensure the ICSP programming pins (ICSPCLK/ICSPDAT) are accessible, and use MPLAB X IDE with XC8 compiler for code development. A 100 nF decoupling capacitor placed within 5 mm of VDD is recommended to suppress switching transients from the digital I/O ring.

RFC Hubungi kami
PIC16F18445-I/GZ - 8-Bit XLP MCU 14KB Flash 20-UQFN | Microchip
PIC16F18445-I/GZ

PIC16F18445-I/GZ - 8-Bit XLP MCU 14KB Flash 20-UQFN | Microchip

The Microchip Technology PIC16F18445-I/GZ is an 8-bit PIC microcontroller built on the PIC® XLP™ 16F architecture with Functional Safety (FuSa) support, delivering 32 MHz CPU performance from 14 KB of self-programmable Flash program memory. It is housed in a 20-pin UQFN 4x4 mm package and targets general-purpose and ultra-low-power embedded designs where small footprint and rich analog peripherals are required. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), and a set of on-chip peripherals such as timers, communication interfaces, ADCs, and GPIO. The PIC16F18445 belongs to the mid-range PIC16F1xxx enhanced family that introduces Core Independent Peripherals (CIPs), allowing complex functions such as signal generation, waveform measurement, and motor control to run in hardware without CPU intervention. Within the broader taxonomy, this part sits at: 8-bit microcontroller → PIC16 family → XLP low-power → functional-safety-capable sub-family → semiconductor device. Key headline specifications include 14 KB Flash program memory (8K x 14 words), 1 KB RAM, 256 bytes of EEPROM data memory, 12-bit ADC with Computation (ADCC), two 10-bit PWMs, an on-chip 5-/8-bit DAC, a Comparator, a Complementary Waveform Generator (CWG), and serial interfaces comprising EUSART, SPI, and I²C. The XLP sleep current can drop below 50 nA in Retention mode, allowing battery-powered products to extend operating life on a single coin cell. The PIC16F18445 integrates the CIP blocks (CWG, NCO, DSM, configurable logic cells, and zero-cross detect) that let designers implement closed-loop SMPS, lighting control, and sensor signal conditioning entirely in silicon. The 12-bit ADCC provides averaging, burst averaging, oversampling, and hardware accumulation, offloading the core from low-level signal processing and enabling precision sensor measurement at low MIPS. Typical applications include IoT sensor nodes, battery-powered thermostats, LED lighting controllers, consumer appliances, automotive body and sensor ECUs (with FuSa documentation), industrial control boards, and wearable health devices. The 4x4 mm UQFN footprint also suits space-constrained designs such as USB-C accessories and small motor-control PCBs. When designing with this part, allocate at least one decoupling 100 nF X7R capacitor adjacent to each VDD/VSS pair and follow Microchip's recommended ground plane layout to keep radiated EMI low. Developers can use the MPLAB X IDE with the free XC8 compiler and PICkit 4 / Snap programmer for in-circuit debug. This page combines distributor pricing, drop-in alternatives, and practical design notes that complement, but do not replace, the manufacturer datasheet and family reference manual.

RFC Hubungi kami
PIC16F18445-I/SO - 8-Bit 32MHz XLP MCU, 14KB Flash | Microchip
PIC16F18445-I/SO

PIC16F18445-I/SO - 8-Bit 32MHz XLP MCU, 14KB Flash | Microchip

The Microchip Technology PIC16F18445-I/SO is an 8-bit PIC microcontroller from the PIC16(L)F184xx family, featuring 14KB (8K x 14) of Flash program memory, 1KB of RAM, and a 32MHz internal oscillator, housed in a 20-pin SOIC (0.295 inch / 7.50mm width) package. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash/RAM/EEPROM), peripherals (ADC, timers, communication), and I/O pins on a single silicon die. PIC16 microcontrollers sit in the product hierarchy as: PIC16 -> PIC10/12/16/18 family -> 8-bit MCU -> microcontroller -> embedded IC -> semiconductor. The XLP (eXtreme Low-Power) designation indicates the family is optimized for ultra-low-power operation, making it ideal for battery-powered applications. The device integrates Core Independent Peripherals (CIPs) including a 12-bit ADC with Computation (ADCC), two 10-bit PWMs, a Digital-to-Analog Converter (DAC), a Comparator, a Complementary Waveform Generator (CWG), and configurable logic cells. Communication is handled by EUSART, SPI, and I2C peripherals. Functional Safety (FuSa) features support IEC 61508 SIL applications. Architecturally, the PIC16F18445 uses an enhanced mid-range 8-bit core with a hardware multiplier and 49 instructions, executing most instructions in one clock cycle at up to 32MHz (8 MIPS). The ADCC automates averaging, oversampling, and threshold comparison without CPU intervention, freeing the core for power-management tasks. Typical applications include IoT sensor nodes, consumer white goods, battery-powered measurement devices, low-power wireless sensor interfaces, LED lighting controllers, and industrial control where tight power budgets and rich analog integration simplify BOM. When designing with this part, budget I/O pins carefully - the 20-pin SOIC exposes 17 I/O, limiting concurrent peripheral use. Plan clock source selection (internal 32MHz HFINTOSC vs. external crystal) early, as the choice affects both power and accuracy. This page synthesizes distributor pricing, same-family drop-in alternatives in SOIC-20, and design notes not consolidated in any single source.

RFC Hubungi kami
PIC16F18445T-I/GZ - 8-bit 32MHz 14KB FLASH MCU 20-UQFN | Microchip
PIC16F18445T-I/GZ

PIC16F18445T-I/GZ - 8-bit 32MHz 14KB FLASH MCU 20-UQFN | Microchip

The Microchip Technology PIC16F18445T-I/GZ is an 8-bit PIC® XLP™ microcontroller from the PIC16(L)F184xx family with Functional Safety (FuSa) capability, 14 KB (8K × 14) of FLASH program memory, 1 KB of RAM, and a maximum CPU clock of 32 MHz, housed in a 20-pin UQFN (GZ) package measuring 4 × 4 mm. An 8-bit microcontroller is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and a configurable set of peripherals around an 8-bit data path. The PIC® XLP™ (eXtreme Low-Power) family extends this with sub-µA sleep currents, making these MCUs the lowest tier of the PIC® microcontroller hierarchy: 8-bit MCU -> PIC16 family -> XLP low-power family -> low-power general-purpose MCU -> semiconductor. The 'Functional Safety (FuSa)' suffix indicates that hardware diagnostics, windowed watchdog, CRC scan and lockable memory are documented for IEC 61508 / ISO 26262 capable designs. Key differentiating features include a 12-bit ADC with Computation (ADCC), a 5-bit DAC, two PWM modules, a Complementary Waveform Generator (CWG), configurable logic cells, an EUSART, and SPI/I²C peripherals. XLP technology delivers sleep currents in the sub-µA range, while active current stays low for battery-driven applications. The 20-UQFN package exposes a thermal pad that, when soldered to the PCB ground pour, dramatically lowers junction-to-ambient thermal resistance compared to leaded equivalents. The PIC16F18445T-I/GZ uses an enhanced mid-range 8-bit CPU core with a hardware multiplier and an instruction set optimized for compiled C. Its interrupt controller, peripheral pin select, and zero-cross detection offload routine work from the core, freeing CPU bandwidth for application logic. The 12-bit ADCC supports averaging, oversampling, and threshold-triggered operations in hardware. Typical applications include battery-powered IoT sensor nodes, industrial sensor transmitters, low-power handheld instrumentation, functional-safety sensor peripherals, white-goods user-interface controllers, and consumer remote controls. Its small footprint and low quiescent current also suit wearables and energy-harvesting endpoints. Design considerations: place 100 nF decoupling close to each VDD pin, route analog/digital grounds as split planes joined at a single star, and follow Microchip's TB3138 PCB layout guidelines for the UQFN exposed pad. The trailing 'T' in the MPN denotes tape-and-reel packaging, and the '-I' indicates the -40 °C to +85 °C industrial temperature grade. This page synthesizes distributor pricing, same-package drop-in alternatives, application notes, and design considerations not aggregated on any single manufacturer page.

RFC Hubungi kami
PIC16F18445T-I/SS - 14KB Flash 8-Bit MCU | Microchip | 20-SSOP
PIC16F18445T-I/SS

PIC16F18445T-I/SS - 14KB Flash 8-Bit MCU | Microchip | 20-SSOP

The Microchip Technology PIC16F18445T-I/SS is an 8-bit microcontroller from the PIC16F184xx family featuring eXtreme Low-Power (XLP) technology and Core Independent Peripherals (CIPs) for general-purpose and low-power applications. The device operates at up to 32 MHz, integrates 14 KB (8K x 14) of Flash program memory and 1 KB of RAM, and is housed in a 20-pin SSOP (Shrink Small Outline Package) with industrial temperature grade (-40C to +85C). A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), and a rich set of on-chip peripherals such as ADCs, timers, communication interfaces, and digital logic blocks. The PIC16 family uses a modified Harvard 8-bit RISC architecture that executes one instruction per clock cycle (except branches), giving it deterministic timing ideal for hard-real-time control loops. Microcontrollers sit in the embedded systems hierarchy between discrete logic and full microprocessors, enabling compact, low-cost, low-power designs. Key features of the PIC16F18445T-I/SS include a 12-bit ADC with Computation (ADCC), a 5-bit DAC, two PWM modules, a comparator, a Complementary Waveform Generator (CWG), and serial interfaces including EUSART, SPI, and I2C. Functional Safety (FuSa) capability and CIPs such as the Configurable Logic Cell (CLC) allow hardware-state machines to run autonomously, offloading the CPU. The device supports 1.8V to 5.5V operation with nanoWatt XLP sleep currents in the order of a few microamps, making it suited to battery-powered and energy-harvesting designs. Typical applications include IoT edge nodes, sensor signal conditioning, low-power wireless sensor interfaces, battery-powered HVAC controls, smart home sensor hubs, and small motor/LED control loops. The trailing 'T' in the part number denotes Tape & Reel packaging, and the 'I' suffix indicates the industrial -40C to +85C operating range. When designing with this part, ensure the configuration words, oscillator selection, and PPS (Peripheral Pin Select) assignments are set in the firmware build - PPS is essential because the I2C, SPI, UART, and PWM functions are remappable to most I/O pins.

RFC Hubungi kami
PIC16F18446-E/GZ - 8-bit MCU, 32MHz, 28KB Flash | Microchip
PIC16F18446-E/GZ

PIC16F18446-E/GZ - 8-bit MCU, 32MHz, 28KB Flash | Microchip

The Microchip Technology PIC16F18446-E/GZ is a 32 MHz 8-bit PIC microcontroller with 28 KB (16K x 14) Flash program memory housed in a 20-pin UQFN (4x4 mm) package with exposed thermal pad. It belongs to the PIC16(L)F184xx family, integrates Functional Safety (FuSa) features, and combines high-resolution Analog, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology for general-purpose and battery-powered applications. An 8-bit microcontroller (MCU) is a self-contained computing element that combines a CPU, non-volatile program memory, data RAM, and peripherals on a single silicon die. The PIC16F18446 sits inside the broader hierarchy: 8-bit microcontroller -> microcontroller (MCU) -> embedded processor -> semiconductor IC. It executes one instruction per cycle from its enhanced mid-range core and supports in-circuit serial programming (ICSP) via two pins, making it well suited for compact, cost-sensitive embedded designs. Key features of the PIC16F18446 include 32 MHz internal oscillator operation (8 MIPS), 2 KB SRAM, 256 bytes of EEPROM, a 12-bit ADC with computation, 8-/16-bit timers, PWM modules, configurable logic cells (CLC), complementary waveform generators (CWG), and multiple serial interfaces (I2C, SPI, UART with LIN). The 20-pin UQFN exposes up to 17 I/O pins with peripheral pin select (PPS) flexibility, allowing remapping of digital peripherals to most I/Os. Architecturally, the device uses a 14-bit instruction-word PIC16 enhanced core with a 16-level hardware stack, hardware multiplier (8x8 in one cycle), and zero-crossing detection on select pins. The XLP Sleep mode drops current consumption to the nanoamp range, and the IDLE/DOZE modes let the CPU sleep while CIPs continue to operate, ideal for always-on sensor polling and energy harvesting designs. Typical applications include low-power sensor nodes, IoT end-node controllers, household appliances, lighting controls, consumer electronics, and battery-powered wearables. The wide operating voltage range and robust peripheral set also suit automotive body and comfort subsystems where the FuSa features accelerate safety documentation. When designing with this MCU, plan the I/O budget against the 20-pin UQFN pinout early: peripheral pin select eases layout, but each function still consumes at least one physical pin. Add an external 100 nF + 1 uF decoupling pair near VDD, and place the ICSP/test pads where a debugger clip or pogo-pin header can reach them.

RFC Hubungi kami
PIC16F18446-E/SO - 28KB Flash 8-bit MCU | Microchip | XLP
PIC16F18446-E/SO

PIC16F18446-E/SO - 28KB Flash 8-bit MCU | Microchip | XLP

The Microchip Technology PIC16F18446-E/SO is an 8-bit PIC microcontroller from the PIC16F184xx family featuring 28KB Flash program memory, 2KB RAM, and a 32MHz internal oscillator in a 20-pin SOIC package. The device integrates Core Independent Peripherals (CIPs) such as a 12-bit Analog-to-Digital Converter with Computation (ADCC), Complementary Waveform Generator (CWG), two 10-bit PWMs, configurable logic cells (CLC), and EUSART/SPI/I2C communication interfaces for low-power general-purpose applications. It is built on the eXtreme Low Power (XLP) technology platform, with typical sleep currents in the nanoampere range, making it well-suited for battery-powered and energy-harvesting designs. An 8-bit PIC microcontroller (MCU) is a compact processor built around a Harvard-architecture RISC core optimized for deterministic real-time control with minimal instruction-cycle overhead. Within the broader hierarchy, a microcontroller is a single-chip computer integrating CPU, RAM, non-volatile program memory, peripherals, and I/O, and the PIC16F184xx family sits in the PIC16 mid-range tier targeting applications that demand low power, integrated analog, and peripheral flexibility without an operating system. Key features include the 28KB (16K x 14) Flash memory, 256 bytes of EEPROM data, 2KB SRAM, 12-bit ADCC with automatic averaging, 5-bit DAC, two comparators, and a Peripheral Pin Select (PPS) system that remaps digital peripheral I/O to a wide range of physical pins. The part supports up to 18 I/O pins and operates from 1.8V to 5.5V across the extended -40C to +125C industrial temperature range, making it broadly compatible with 3.3V and 5V system rails. Typical applications include IoT sensor nodes, consumer white goods, low-power wireless sensor hubs, lighting controls, and small home appliances. The integrated 12-bit ADCC allows direct interfacing with analog sensors such as thermistors, photocells, and battery monitors without an external ADC. The CWG and CLC enable flexible waveform synthesis and event-driven logic without CPU intervention, freeing core bandwidth for higher-level tasks. The EUSART/SPI/I2C interfaces are suitable for connecting to external sensors, displays, EEPROM, or RF front-end modules. When designing with this MCU, allocate adequate decoupling (100 nF plus 1 uF to 10 uF bulk) near VDD, route the ICSP programming pins (ICSPCLK/ICSPDAT) to a header that is accessible for in-circuit programming, and use Microchip's MPLAB X IDE with the XC8 compiler. The PPS system should be configured in software early in initialization to remap peripheral functions to chosen pins. This page synthesizes distributor pricing across 11 channels, drop-in 20-SOIC alternatives, and practical design notes not found in the standalone manufacturer datasheet, helping engineers select, source, and integrate the PIC16F18446-E/SO confidently.

RFC Hubungi kami
PIC16F18446-E/SS - 32MHz 8-bit MCU, 28KB Flash, 20-SSOP | Microchip
PIC16F18446-E/SS

PIC16F18446-E/SS - 32MHz 8-bit MCU, 28KB Flash, 20-SSOP | Microchip

The Microchip Technology PIC16F18446-E/SS is an 8-bit RISC PIC16 microcontroller operating at up to 32MHz, integrating 28KB (16K x 14 words) of Flash program memory, 2KB SRAM and 256 bytes of EEPROM, housed in a 20-pin SSOP package. It belongs to the PIC16(L)F184xx family which combines Intelligent Analog, Core Independent Peripherals (CIPs) and eXtreme Low-Power (XLP) technology for general purpose and battery powered applications. An 8-bit microcontroller (MCU) is a programmable semiconductor device that integrates a CPU, non-volatile program memory, working RAM, and a rich set of on-chip peripherals (ADC, timers, communication ports, comparators) into a single chip. Within the broader taxonomy, this places the PIC16F18446 in the MCU -> microcontroller -> embedded controller -> semiconductor IC hierarchy. Microcontrollers are the brain of embedded systems and are used wherever sensor data must be read, decisions made, and actuators driven - from a thermostat to a motor controller to a wireless sensor node. Key features include a 32MHz internal oscillator, a 12-bit ADC with computation (ADC2) that offloads averaging and threshold detection from the CPU, two PWM modules, a Complementary Waveform Generator (CWG), a 5-bit DAC, comparators, EUSART, SPI and I2C. The device operates from 1.8V to 5.5V and offers Active current below 1mA/MHz with sleep currents in the nanoamp range via XLP modes, enabling years of operation from a single coin cell. Typical applications include low-power sensor end nodes (IoT), battery powered remote controls, home appliances, lighting controls, sensor signal conditioning nodes and small motor or fan controllers. The high-resolution analog and CIPs allow the ADC, threshold detection and PWM to run without CPU intervention, dramatically reducing active time and overall power consumption. When designing with this device, choose the SSOP-20 variant when PCB height is constrained and 14-20 GPIO pins are sufficient. For pin-constrained designs below 20 pins, the PIC16F18426 family shares the same peripherals in 14-pin packages. Always provide a 0.1uF decoupling capacitor within a few millimeters of VDD. This page synthesizes distributor pricing, drop-in same-package alternatives and practical design notes that are not aggregated on the manufacturer product page or distributor catalog.

RFC Hubungi kami
PIC16F18446-I/GZ - 28KB Flash 8-bit MCU, 32MHz, 20-UQFN | Microchip
PIC16F18446-I/GZ

PIC16F18446-I/GZ - 28KB Flash 8-bit MCU, 32MHz, 20-UQFN | Microchip

The Microchip Technology PIC16F18446-I/GZ is an 8-bit PIC microcontroller from the PIC16(L)F184xx family featuring 28KB (16K x 14) of Flash program memory, 2KB of RAM, and a maximum CPU clock of 32MHz, housed in a compact 20-pin UQFN (4x4 mm) package. It belongs to the PIC® XLP™ (eXtreme Low-Power) lineup and is rated for Functional Safety (FuSa) applications, integrating Core Independent Peripherals (CIPs) that execute tasks in hardware without CPU intervention. An 8-bit microcontroller (MCU) is a single-chip computer that uses an 8-bit data path, optimized for cost-sensitive, low-power, and deterministic embedded applications. Within the broader taxonomy, the PIC16F18446 sits as: PIC microcontroller -> 8-bit MCU -> microcontroller unit -> semiconductor device. The PIC16F184xx family specifically targets sensor end-node, IoT, and battery-powered designs where active current, sleep current, and integration density dominate the design trade-offs. Key features include a 12-bit ADCC (Analog-to-Digital Converter with Computation), a 5-bit DAC, two PWM modules, a Comparator, a Complementary Waveform Generator (CWG), and communication peripherals (EUSART, SPI, I2C). The on-chip CIPs such as the CWG and ADCC enable closed-loop hardware control of sensors, LEDs, and power stages without waking the CPU, dramatically reducing average power consumption. The 20-UQFN package (4x4 mm) provides a minimal PCB footprint suitable for space-constrained wearable and IoT modules. Typical applications include IoT sensor end nodes, battery-powered wireless transmitters, home automation controllers, low-power edge sensors, LED lighting controllers, and consumer appliance user interfaces. The wide 2.3V to 5.5V operating voltage range enables direct connection to 2x AA / coin-cell stacks or 3.3V regulated rails. The XLP sleep currents in the nanoampere range allow multi-year battery life on duty-cycled nodes. When designing with this device, allocate PCB area for the exposed thermal pad on the UQFN, use a 0.1 µF decoupling capacitor adjacent to VDD, and configure the unused I/O pins as outputs to minimize sleep current. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFC Hubungi kami
PIC16F18446-I/SO - 8-bit XLP MCU, 28KB Flash, 32MHz | Microchip
PIC16F18446-I/SO

PIC16F18446-I/SO - 8-bit XLP MCU, 28KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F18446-I/SO is an 8-bit PIC microcontroller built on the enhanced mid-range PIC16 CPU core, delivering up to 32 MHz operation with 28 KB (16K x 14) of Flash program memory and 2 KB of SRAM, housed in a 20-pin SOIC package with industrial-grade -40C to +85C temperature range. The device integrates 256 bytes of EEPROM data memory, a 12-bit Analog-to-Digital Converter with Computation (ADCC), two 10-bit PWMs, a 5-bit DAC, comparators, a Complementary Waveform Generator (CWG), and EUSART/SPI/I2C communication peripherals. It belongs to the PIC16(L)F184xx family that features Core Independent Peripherals (CIPs) and eXtreme Low-Power (XLP) technology for battery-powered and energy-harvesting applications. An 8-bit microcontroller (MCU) is a compact programmable processor that combines a CPU, non-volatile program memory, RAM, and peripheral interfaces on a single silicon die. The "PIC" architecture uses a modified Harvard layout with separate program and data buses; the PIC16F18446 specifically runs the enhanced mid-range core that supports 49 instructions and a 16-level hardware stack. Within the broader taxonomy, the PIC16F18446 is an 8-bit MCU, which sits below 16-bit dsPIC and 32-bit ARM Cortex-M devices in computational capability but excels in deterministic real-time response, ultra-low sleep current, and small package footprint - making it favored for sensor end-nodes, appliance control, and human-interface peripherals. Key differentiating features include the 12-bit ADCC with automated hardware averaging and threshold comparison that offloads the CPU, the CWG that synthesizes complementary PWM outputs for power-conversion dead-band control, and the Peripheral Pin Select (PPS) module that routes digital peripherals to any I/O pin. The XLP technology delivers typical sleep currents below 50 nA with retention, enabling multi-year coin-cell battery life in wireless sensor nodes. Typical applications include IoT sensor end-nodes, battery-powered remote controls, LED lighting controllers, BLDC motor pre-drivers, white-goods user interfaces, and industrial sensor transmitters. The integrated 12-bit ADC and CIPs make it particularly suited to hardware-based sensor signal conditioning where the CPU remains in sleep until a threshold is crossed.

RFC Hubungi kami
PIC16F18446T-I/GZ - 8-bit 32MHz 28KB Flash XLP MCU | Microchip
PIC16F18446T-I/GZ

PIC16F18446T-I/GZ - 8-bit 32MHz 28KB Flash XLP MCU | Microchip

The Microchip Technology PIC16F18446T-I/GZ is an 8-bit PIC microcontroller from the PIC16(L)F184xx family featuring eXtreme Low-Power (XLP) technology and Functional Safety (FuSa) support. It integrates 28KB (16K x 14 words) of Flash program memory, 2KB of RAM, and runs at up to 32 MHz in a compact 20-pin UQFN (4x4 mm) package. Core Independent Peripherals (CIPs) include dual 10-bit PWMs, a Complementary Waveform Generator (CWG), 12-bit ADC with Computation (ADCC), 5-bit and 8-bit DACs, comparators, EUSART, SPI, and I2C communication interfaces. An 8-bit microcontroller is a small computing-on-a-chip that executes instructions 8 bits wide at a time. It sits within the broader hierarchy of microcontrollers -> embedded microcontrollers -> semiconductor ICs, and is the workhorse of low-power, deterministic, cost-sensitive embedded designs. The PIC16F18446 specifically belongs to the mid-range PIC16 family, which adds CIPs to handle I/O tasks in hardware without burdening the CPU. Key features of this part include operation from 2.3V to 5.5V, an integrated 32 MHz internal oscillator, low-power sleep currents in the nanoampere range via XLP, and CIPs that let designers offload timing-critical functions to hardware. The 12-bit ADCC performs averaging, oversampling, and threshold comparison in hardware, while the CWG can synthesize dead-band-controlled complementary outputs for power-switching applications. Architecturally, the PIC16F18446 uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word, hardware multiplier, and direct addressing of up to 32KB of Flash. The CIP block includes Numerically Controlled Oscillator (NCO), CWG, and configurable logic cells that act as glue logic on-chip, reducing BOM and PCB area. Typical applications include IoT sensor end nodes, low-power battery-operated products, LED lighting controllers, consumer appliances, and small motor control. Its 20-pin UQFN footprint suits space-constrained designs. When designing, ensure the supply decoupling follows the layout in the datasheet's typical application circuit. For FuSa-required systems, consult Microchip's functional safety documentation for diagnostic coverage and FMEDA data. This page consolidates distributor pricing, drop-in same-package alternatives, and practical design notes drawn from Microchip's PIC16F18446 datasheet and reference designs.

RFC Hubungi kami
PIC16F18446T-I/SO - 8-Bit 32MHz 28KB Flash XLP MCU | Microchip
PIC16F18446T-I/SO

PIC16F18446T-I/SO - 8-Bit 32MHz 28KB Flash XLP MCU | Microchip

The Microchip Technology PIC16F18446T-I/SO is an 8-bit PIC16 (L)F184xx family microcontroller featuring 28KB (16K x 14 words) of Flash program memory, 2KB of RAM, and a 32MHz internal oscillator, housed in a 20-pin SOIC package with the industry-standard 0.295" (7.50mm) body width. The "T" suffix denotes Tape & Reel packaging, while the "I" indicates the industrial -40C to +85C operating temperature range. What is a PIC16 XLP microcontroller? An 8-bit MCU (microcontroller unit) is a single-chip computer integrating a CPU core, Flash memory, RAM, and programmable peripherals on one silicon die; the PIC16 family uses a RISC instruction set, and XLP (eXtreme Low Power) denotes Microchip's proprietary nanoWatt technology that enables sleep currents in the tens of nanoamps, allowing battery-powered applications to operate for years on a single cell. Key differentiating features of the PIC16F18446 include Core Independent Peripherals (CIPs) such as the 12-bit ADCC (Analog-to-Digital Converter with Computation), 5-bit DAC, two PWM modules, comparators, CWG (Complementary Waveform Generator), and the EUSART plus SPI/I2C serial interfaces. Functional Safety (FuSa) capability is built in, and the device operates from 1.8V to 5.5V across industrial and consumer temperature grades. Architecturally, the PIC16F18446 combines a Harvard RISC core running up to 32MHz (8 MIPS) with 14-bit instruction words, providing deterministic interrupt latency under 5 cycles and a compact code footprint. The integrated 32MHz HFINTOSC eliminates the need for an external crystal in most designs, while the 16-channel 12-bit ADCC handles sensor fusion, signal conditioning, and battery monitoring without external analog components. Typical applications include low-power IoT sensor nodes, battery-powered home automation, LED lighting controls, small consumer appliances, and industrial sensor interfaces. The wide operating voltage range and nanoWatt XLP modes also suit wearables and remote controls where standby current dominates total energy budget. When designing with this MCU, place a 0.1uF decoupling capacitor close to VDD and use the ICSP programming pins (PGED/PGEC) with a 10k pull-up on MCLR to ensure reliable in-circuit programming. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes not found in the manufacturer datasheet.

RFC Hubungi kami
PIC16F18455-E/SO - 14KB Flash 8-bit MCU | Microchip XLP | 28-SOIC
PIC16F18455-E/SO

PIC16F18455-E/SO - 14KB Flash 8-bit MCU | Microchip XLP | 28-SOIC

The Microchip Technology PIC16F18455-E/SO is a 14KB Flash 8-bit microcontroller from the PIC16F184xx family featuring XLP (eXtreme Low Power) technology and Core Independent Peripherals (CIPs). It operates at up to 32MHz, integrates 14KB (8K x 14 words) of Flash program memory, 1KB of RAM, and offers peripheral connectivity including 2x PWMs, a Comparator, a 5-bit DAC, 12-bit ADCC, CWG, EUSART, and SPI/I2C. The device is housed in a 28-pin SOIC (7.50mm/0.295in width) surface-mount package and supports an extended operating temperature range from -40C to +125C. An 8-bit PIC microcontroller is a compact, low-power RISC-based computing core optimized for embedded control tasks. It sits within the broader hierarchy of microcontroller -> embedded processor -> semiconductor IC, where it competes with 32-bit ARM Cortex-M0 devices for low-cost general-purpose applications. The 8-bit architecture retains advantages in code density, deterministic timing, and ease of use through MPLAB X IDE and XC8 toolchain. The XLP designation indicates the family targets battery-powered and energy-harvesting designs with deep-sleep current measured in nanoamps. Key features include a 12-bit Analog-to-Digital Converter with Computation (ADCC) for automated averaging and threshold detection, a 5-bit DAC for analog setpoint generation, a Complementary Waveform Generator (CWG) for power-converter gate-drive signals, and a Zero-Cross Detect (ZCD) module. The device supports 1.8V to 5.5V VDD operation, making it suitable for both 3.3V and 5V systems. Peripherals such as EUSART, SPI, and I2C enable flexible communication with sensors and master controllers. Typical applications include low-power IoT sensor nodes, consumer electronics with capacitive touch sensing via the MTouch peripheral, battery-powered home automation, and industrial control blocks. The combination of XLP sleep current, the 12-bit ADCC, and on-chip DAC eliminates many external analog components, reducing BOM cost and PCB area in space-constrained designs. When designing with this device, place a 100nF decoupling capacitor as close as possible to the VDD pin, and route MCLR through a 10k pull-up. Confirm that the 32MHz internal oscillator accuracy is sufficient for your timing budget, or specify an external crystal for UART-bound communication. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFC Hubungi kami
PIC16F18455-E/SS - 14KB Flash 8-bit MCU, 32MHz, SSOP-28 | Microchip
PIC16F18455-E/SS

PIC16F18455-E/SS - 14KB Flash 8-bit MCU, 32MHz, SSOP-28 | Microchip

The Microchip Technology PIC16F18455-E/SS is an 8-bit PIC microcontroller featuring 14KB Flash program memory, 1KB RAM, and a 32MHz internal oscillator, housed in a 28-pin SSOP package. It belongs to the PIC16(L)F184xx family, which combines Intelligent Analog, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology for general-purpose and battery-powered applications. Operating voltage spans 2.3V to 5.5V across an industrial -40C to +125C temperature range. An 8-bit microcontroller (MCU) is a small computer on a single integrated circuit containing a CPU, memory (Flash, RAM, EEPROM), and programmable I/O peripherals. PIC microcontrollers use a modified Harvard RISC architecture, executing one instruction per clock cycle (except branches) to deliver deterministic performance at low clock rates. PIC MCUs sit within the broader hierarchy of: microcontroller -> embedded processor -> integrated circuit -> semiconductor. Compared with 16-bit or 32-bit MCUs, 8-bit parts typically deliver lower cost, lower power, and simpler toolchains for sensing, control, and human-interface tasks. Key features include a 12-bit Analog-to-Digital Converter with Computation (ADC2), two PWM modules, a Digital-to-Analog Converter (DAC), a Comparator, a Complementary Waveform Generator (CWG), EUSART, and SPI/I2C interfaces. The device integrates CIPs that offload timing-critical tasks from the CPU, enabling deterministic response without firmware intervention. The PIC16F18455 uses an enhanced mid-range 8-bit core with a 14-bit instruction word, supporting interrupt-driven and core-independent operation. Internal voltage reference, temperature indicator, and zero-cross detection extend its analog capability, while Memory Access Partitioning (MAP) and Device Information Area (DIA) support bootloader and calibration flows. Typical applications include IoT sensor nodes, battery-powered instrumentation, consumer appliances, LED lighting controllers, low-cost motor control, and industrial automation peripherals. The XLP feature set (sleep currents below 1 uA typical with full RAM retention) makes it suitable for energy-harvesting and remote-control products. Design tip: choose the SSOP-28 variant over the SOIC-28 only when board height is constrained; both share the same 0.65mm pitch and are drop-in pin-compatible. For automotive qualification, select the -I or -E temperature grades as required by the target environment. This page synthesizes distributor pricing, drop-in PIC16F184xx alternatives, and practical design notes not found in the manufacturer datasheet alone, providing an at-a-glance comparison of compatible 28-pin SSOP 8-bit MCUs.

RFC Hubungi kami
PIC16F18455-I/SO - 8-bit 32MHz 14KB Flash MCU | Microchip
PIC16F18455-I/SO

PIC16F18455-I/SO - 8-bit 32MHz 14KB Flash MCU | Microchip

The Microchip PIC16F18455-I/SO is an 8-bit PIC microcontroller from the PIC16(L)F184xx family, featuring a 32 MHz internal oscillator, 14 KB (8K x 14 words) of Flash program memory, 1 KB of RAM and 256 bytes of EEPROM, and a 12-bit ADC with Computation (ADC2). Housed in a 28-pin SOIC wide-body (SO) package, the -I suffix indicates the industrial temperature grade (-40C to +85C). An 8-bit microcontroller (MCU) is a small, low-power programmable processor built around an 8-bit data path, optimized for embedded control rather than raw computational throughput. The PIC16F18455 belongs to the broader class of microcontrollers within the semiconductor hierarchy: MCU -> embedded processor -> integrated circuit. It uses Microchip's enhanced mid-range 16-bit instruction set running on an 8-bit data bus, giving deterministic execution and very low power draw suitable for battery-powered edge devices. Key features include eXtreme Low-Power (XLP) technology with currents in the nanoamp range in sleep, Core Independent Peripherals (CIPs) such as CWG, NCO, DSM and configurable logic cells, Memory Access Partitioning (MAP) for bootloader support, and a Device Information Area (DIA) for unique serialization. The 12-bit ADC2 performs automated averaging, filtering and threshold comparisons without CPU intervention. Typical applications include low-power IoT sensor nodes, battery-powered HVAC and thermostat controls, automotive interior lighting and body controllers, consumer appliances, and general-purpose logic replacement. The wide 1.8V to 5.5V operating range and rich peripheral set let one part cover analog sensing, PWM-driven loads and serial communication in a single device. When designing with this part, ensure decoupling capacitors are placed within a few millimeters of VDD/VSS pins and that the ICSP programming footprint is retained on production boards to allow in-field firmware updates. The 28-SOIC wide package (7.50 mm body) is the most serviceable hand-solder option for prototype runs.

RFC Hubungi kami
PIC16F18455-I/SP - 8-bit MCU 14KB Flash 32MHz 28-SPDIP | Microchip
PIC16F18455-I/SP

PIC16F18455-I/SP - 8-bit MCU 14KB Flash 32MHz 28-SPDIP | Microchip

The Microchip Technology PIC16F18455-I/SP is an 8-bit PIC microcontroller from the PIC16F184xx family, featuring 14KB Flash program memory, 1KB RAM, and a 32MHz internal oscillator in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. It combines high-resolution analog peripherals, Core Independent Peripherals (CIPs), and eXtreme Low-Power (XLP) technology, targeting general-purpose and energy-conscious embedded designs. An 8-bit microcontroller is a single-chip computer built around an 8-bit data path, integrating a CPU, Flash program memory, SRAM, and a rich set of peripherals such as ADCs, timers, communication interfaces, and Core Independent Peripherals (CIPs). The PIC16F18455 sits within the larger taxonomy of microcontrollers -> 8-bit MCUs -> PIC16 family -> PIC16F184xx sub-family -> 16KB-Flash low-pin-count devices. It is widely used where deterministic real-time control, low active and sleep power, and compact analog integration matter more than raw MIPS. Key features include 14KB (8K x 14 words) self-programmable Flash, 1KB RAM, 256-byte EEPROM, a 12-bit ADC with Computation (ADCC), 10-bit DAC, two PWMs, a Complementary Waveform Generator (CWG), EUSART, SPI, I2C, and a configurable Logic Cell. The 12-bit ADCC supports automated averaging, threshold comparison, and hardware accumulator, offloading signal conditioning from the CPU. Architecturally, the PIC16F18455 uses an enhanced mid-range 8-bit core with a 14-bit instruction word and a hardware multiplier, enabling C-compiled firmware at 32MHz while retaining PIC predictability. XLP technology drives active currents to the sub-100 µA/MIPS range and sleep currents below ~50 nA typical, supporting battery-sourced and energy-harvesting products. Typical applications include low-power IoT sensor nodes, consumer white goods, HVAC controls, battery-powered instrumentation, LED lighting controllers, and industrial sensor signal conditioning. Designers benefit from the combination of 12-bit analog accuracy and tiny quiescent draw in a single through-hole device. When designing, select the -I variant (industrial, -40C to +85C) for non-automotive deployments and the -E variant for extended temperature grades. Decoupling 100nF ceramic capacitors at every VDD/VSS pair and a 10µF bulk cap near the MCU are recommended for ADCC noise performance. This page synthesizes real distributor pricing as of 2026-09-20, drop-in same-package alternatives, and practical design guidance beyond what appears in the manufacturer datasheet.

RFC Hubungi kami
PIC16F18455-I/SS - 8-Bit 32MHz 14KB Flash XLP MCU | Microchip
PIC16F18455-I/SS

PIC16F18455-I/SS - 8-Bit 32MHz 14KB Flash XLP MCU | Microchip

The Microchip Technology PIC16F18455-I/SS is an 8-bit RISC PIC16F microcontroller running up to 32 MHz with 14 KB (8K x 14) of Flash program memory, 1 KB of SRAM, and 256 bytes of EEPROM, packaged in a 28-pin SSOP (5.30 mm body). It belongs to the PIC16(L)F184xx family, which pairs high-resolution analog, Core Independent Peripherals (CIPs) such as CLC, CWG, NCO, and configurable logic, with eXtreme Low-Power (XLP) technology for general-purpose and battery-driven designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripheral I/O, and interrupt control on one die. The PIC16F18455's 8-bit Harvard architecture executes one instruction per cycle (excluding branches), and its XLP lineage targets sleep currents in the nanoamp range with active run currents below 1 mA/MHz. Key features include 14 KB self-programmable Flash, 1 KB SRAM, 256 B EEPROM, an integrated 10-bit ADC with computation, multiple 8/16-bit timers, EUSART, SPI, and I2C peripherals, a 32 MHz internal oscillator, and an operating range of -40 °C to +85 °C (industrial grade). The 28-SSOP footprint exposes up to 25 digital I/O, including interrupt-on-change, with peripheral pin select (PPS) routing. The device combines a low-power analog complement with Core Independent Peripherals, allowing capacitive sensing, power-supply signaling, and real-time control without CPU intervention. Hardware CIPs such as the Configurable Logic Cell (CLC), Complementary Waveform Generator (CWG), and Numerically Controlled Oscillator (NCO) offload tasks from the CPU, reducing active-mode power and freeing MIPS for application code. Typical applications include low-power IoT sensor nodes, battery-powered HVAC controls, automotive body and interior ECUs, white goods and appliance HMI, LED lighting controllers, and general-purpose 8-bit embedded products. The 32 MHz core plus PPS gives designers flexibility to remap peripherals, while XLP enables multi-year coin-cell operation. When designing with this part, place a 100 nF decoupling capacitor within 2 mm of VDD and connect unused I/O to a defined logic level to minimize current draw. Programming is supported by Microchip's MPLAB X IDE with free XC8 compiler; in-circuit serial programming (ICSP) uses only two pins, simplifying board layout and field upgrades. This page synthesizes distributor pricing, drop-in 28-SSOP alternatives, application notes, and practical design guidance that complement the manufacturer datasheet for engineers evaluating the PIC16F18455-I/SS.

RFC Hubungi kami
PIC16F18455-I/STX - 8-bit XLP MCU 14KB Flash 32MHz | Microchip
PIC16F18455-I/STX

PIC16F18455-I/STX - 8-bit XLP MCU 14KB Flash 32MHz | Microchip

The Microchip Technology PIC16F18455-I/STX is an 8-bit PIC RISC microcontroller with 14KB (8K x 14 words) of Flash program memory, 1KB of SRAM, and 256 bytes of data EEPROM, operating up to 32MHz and housed in a 28-pin VQFN (4x4 mm) package with exposed thermal pad. It integrates a 12-bit ADC with Computation (ADCC), two 10-bit PWMs, a 5-bit DAC, a comparator, a Complementary Waveform Generator (CWG), and serial interfaces including EUSART, SPI, and I2C, all in the low-pin-count PIC16F184xx family. What is an 8-bit PIC microcontroller? An 8-bit PIC microcontroller is a Harvard-architecture, RISC-based microcontroller that fetches instructions from Flash program memory and operates on 8-bit data words in a single CPU cycle. PIC MCUs belong to the broader category of microcontrollers (MCU) within embedded processors, themselves a subset of integrated circuits. They sit at the lowest tier of the embedded computing hierarchy - below 16-bit dsPIC, 32-bit ARM Cortex-M0/M4, and application processors - and are typically chosen for cost-sensitive, deterministic, peripheral-rich applications where a full 32-bit core would be overkill. Key features include eXtreme Low-Power (XLP) technology with sub-1 uA sleep current, Core Independent Peripherals (CIPs) that operate without CPU intervention, and a 32MHz internal oscillator with 1% accuracy. The 12-bit ADCC performs automated averaging, threshold detection, and oversampling in hardware, offloading signal-conditioning work from the CPU. Multiple power-managed operating modes - Run, Doze, Idle, Sleep, and Peripheral Module Disable (PMD) - let developers minimize quiescent draw in battery-powered designs. Typical applications include consumer IoT sensor nodes, low-power handheld instruments, LED lighting controllers, battery-powered motor control loops, and small appliance user interfaces. The combination of 14KB Flash and 1KB SRAM is sufficient for state-machine firmware, basic protocol stacks (Modbus, LIN slave), and PID control loops without external memory. When designing with this MCU, budget I/O pins carefully: the 28-VQFN exposes roughly 24 GPIO pins, with several shared between analog inputs and digital peripherals. Always reserve the ICSPDAT/ICSPCLK pins (typically RB6/RB7) for in-circuit serial programming unless the design includes a dedicated debug header.

RFC Hubungi kami
PIC16F18455T-I/SO - 14KB Flash 8-bit XLP MCU 28-SOIC | Microchip
PIC16F18455T-I/SO

PIC16F18455T-I/SO - 14KB Flash 8-bit XLP MCU 28-SOIC | Microchip

The Microchip Technology PIC16F18455T-I/SO is an 8-bit RISC microcontroller in the PIC16(L)F184xx family with 14KB Flash program memory, 1KB RAM, and a 32MHz internal oscillator, housed in a 28-pin SOIC package with industrial -40C to +85C temperature grade. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash, RAM, EEPROM), and peripherals on one silicon die. The PIC16F18455 sits in the hierarchical family PIC16F18455 -> PIC16F184xx -> PIC16 -> PIC microcontrollers -> 8-bit microcontrollers -> microcontrollers -> integrated circuits. Microchip's PIC16 family is a workhorse of low-power and general-purpose embedded designs thanks to the eXtreme Low-Power (XLP) technology that delivers nanoWatt sleep currents. Key features include 14KB (8Kx14 words) of self-programmable Flash, 1KB data SRAM, 256B EEPROM, a 12-bit ADC with Computation (ADC2), 2 PWMs with complementary waveform generation, a 5-bit DAC, two comparators, EUSART, SPI, I2C, a Complementary Waveform Generator (CWG), and Core Independent Peripherals (CIPs) that offload tasks from the CPU. The device operates from 2.3V to 5.5V across -40C to +125C. The architecture uses a Harvard-style 8-bit RISC core with a modified 14-bit instruction word optimized for code density. Core Independent Peripherals (CIPs) such as the CWG, NCO, and configurable logic cells let the chip handle timing-critical events without CPU intervention, freeing the core for application logic and reducing firmware complexity. Typical applications include battery-powered IoT sensor nodes, low-power wireless remotes, HVAC controls, small appliances, LED lighting controllers, and consumer white-goods user-interface boards. The trailing 'T' in the part number designates Tape and Reel packaging, and the '/SO' suffix identifies the 300-mil 28-pin SOIC. When designing with this part, ensure your programmer/debugger is compatible with the device's In-Circuit Serial Programming (ICSP) interface and verify the SOIC pad pitch against your PCB footprint. For applications below 2.5V, drop to 16MHz CPU speed; for full 32MHz operation, keep VDD at 2.5V or above. This page synthesizes distributor pricing, drop-in PIC16F184xx and PIC16F182xx family alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFC Hubungi kami
PIC16F18455T-I/SS - 32MHz 8-bit MCU, 14KB Flash, 28-SSOP
PIC16F18455T-I/SS

PIC16F18455T-I/SS - 32MHz 8-bit MCU, 14KB Flash, 28-SSOP

The Microchip Technology PIC16F18455T-I/SS is an 8-bit RISC microcontroller from the PIC16F18455 family, featuring 14 KB of Flash program memory, 1 KB of SRAM, and a 32 MHz internal oscillator in a 28-pin SSOP (Tape and Reel) package. The device integrates Core Independent Peripherals (CIPs), eXtreme Low-Power (XLP) technology, and high-resolution analog including a 12-bit ADC with Computation (ADC2), a 5-bit DAC, and up to two comparators. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash), data memory (RAM), and a range of peripherals onto one die. Within the broader semiconductor taxonomy, MCUs belong to the embedded controller category, sitting beneath microprocessors in processing power but above simple logic ICs in functional integration. PIC16F series devices are Microchip's mid-range 8-bit family, optimized for low-power general-purpose and consumer/industrial applications. Key features of the PIC16F18455T-I/SS include 14 KB (8K x 14 words) of self-programmable Flash, 1 KB of SRAM, 256 bytes of EEPROM, 26 I/O pins, and rich on-chip peripherals: 2 EUSART, 2 MSSP (SPI/I2C), 2 PWM modules with complementary outputs, CWG (Complementary Waveform Generator), 12-bit ADC2, 5-bit DAC, 2 comparators, and a windowed WDT. The XLP deep-sleep current is typically under 50 nA with full RAM retention. The PIC16F18455 architecture uses a Harvard RISC core with a 14-bit instruction word and single-cycle execution at 32 MHz (8 MIPS). The 12-bit ADC2 with computation automates averaging, threshold comparison, and oversampling, reducing firmware burden. Peripheral Pin Select (PPS) and Memory Access Partitioning (MAP) provide flexible pin remapping and bootloader protection. Typical applications include low-power IoT sensor nodes, battery-powered consumer devices, smart home controls, LED lighting controllers, small appliance user interfaces, and industrial sensor conditioning. The XLP nanoWatt features and 32 MHz performance balance responsive computation with multi-year battery life. When designing with this part, allocate at least one decoupling capacitor per power pin (typically 100 nF ceramic) and follow Microchip's MPLAB X IDE / XC8 compiler toolchain. The wide 1.8 V to 5.5 V supply range enables both single-cell Li-ion and 5 V regulated designs. This page synthesizes distributor pricing, drop-in package alternatives, and practical design notes not found in the manufacturer datasheet alone, providing engineers with a faster selection path for the PIC16F18455 family.

RFC Hubungi kami
PIC16F18456-E/SS - 8-bit MCU, 32MHz, 28KB Flash, 28-SSOP | Microchip
PIC16F18456-E/SS

PIC16F18456-E/SS - 8-bit MCU, 32MHz, 28KB Flash, 28-SSOP | Microchip

The Microchip Technology PIC16F18456-E/SS is an 8-bit PIC microcontroller from the PIC16(L)F184xx family featuring Core Independent Peripherals (CIPs), high-resolution analog peripherals, and eXtreme Low-Power (XLP) technology. It integrates 28KB of Flash program memory, 2KB of RAM, and operates at up to 32MHz in a 28-pin SSOP package (Extended temperature grade -40C to +125C). A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and programmable peripherals. The PIC16F18456 belongs to the 8-bit MCU category (8-bit CPU data path -> microcontroller -> embedded controller -> semiconductor IC), positioned for general-purpose and low-power embedded designs. The 16F184xx family specifically targets applications that combine analog signal conditioning with serial communication, replacing multi-chip discrete solutions. Key features include a 12-bit Analog-to-Digital Converter with Computation (ADCC), a 5-bit and 8-bit Digital-to-Analog Converter (DAC), two PWMs, a Complementary Waveform Generator (CWG), a Comparator, EUSART, and two SPI/I2C interfaces. These CIPs allow hardware-based signal generation and conditioning without CPU intervention, freeing the core for application logic and reducing firmware complexity. The PIC16F18456 uses a RISC architecture with a modified Harvard memory layout, providing deterministic interrupt response and predictable instruction timing. The XLP technology delivers deep-sleep currents below 1uA in sleep mode with retention, making it suitable for battery-powered sensor nodes. The 32MHz internal oscillator removes the need for an external crystal in most designs. Typical applications include IoT sensor nodes, low-power wireless sensor interfaces, battery-powered home automation, industrial control, automotive body electronics, and consumer appliances. The combination of 12-bit ADC, DAC, and PWM makes it well-suited for closed-loop motor control and LED lighting. The EUSART and dual SPI/I2C enable bridging to sensor, display, or wireless modules. When designing with this device, allocate sufficient decoupling (100nF + 1uF) close to VDD, route the ICSP programming pins to a debug header, and configure the configuration bits (FOSC, WDTE, etc.) in your project settings. The 28-SSOP package is hand-solderable for prototyping but is best assembled in volume via reflow. This page synthesizes distributor pricing from DigiKey, Mouser, and LCSC, plus drop-in alternatives from the PIC16F184xx family and pin-compatible variants, plus practical design notes not aggregated in the manufacturer datasheet.

RFC Hubungi kami