AD515JH/+ Precision J-FET Op Amp | Analog Devices
MPN: AD515JH/+ ✗ End of LifeAD515JH/+ Overview
A J-FET-input operational amplifier is an operational amplifier whose input stage uses junction field-effect transistors. This input architecture belongs to the broader hierarchy of operational amplifier, analog amplifier, analog signal-conditioning IC, and semiconductor. Compared with bipolar-input amplifiers, J-FET inputs are commonly selected when very low input bias current, high source impedance, sensor-interface capability, and low distortion are more important than low-voltage operation or minimum cost.
The AD515JH/+ combines one amplifier circuit with a low-power FET-input design and an electrometer-amplifier function. Verified product descriptions identify the device as a monolithic precision device. Input offset voltage is listed up to 3000 uV. Additional operating limits, noise, gain-bandwidth product, slew rate, input bias current, supply-current range, common-mode range, and temperature limits must be confirmed against the manufacturer datasheet before the amplifier is released into a new precision measurement design.
The 8-lead TO-99 package is mechanically distinct from modern surface-mount and small-outline packages. A replacement therefore requires more than matching the amplifier category: the engineer should verify every terminal function, offset polarity, supply arrangement, package dimensions, thermal constraints, and electrical limits. The AD515JH/+ is best treated as a legacy instrumentation-amplifier building block for equipment where its established footprint and electrical behavior are already part of the system design.
Typical uses include high-impedance sensor signal conditioning, pH and ion-sensitive measurement front ends, photodiode amplifiers, capacitance measurement, laboratory instrumentation, and low-current transducers. In each circuit, the principal design task is preserving signal integrity from the sensor through the amplifier input while avoiding input-bias-current error and unintended parasitic capacitance at the feedback network.
For a new PCB, reproduce the TO-99-8 land pattern and pin orientation directly from the Analog Devices datasheet, including any exposed metal-can or case-potential connection. Use guarding, a single-point analog ground strategy, short feedback traces, and clean separation from switching nodes. Before substitution, compare offset voltage, bias current, noise, gain bandwidth, common-mode voltage, supply range, and temperature behavior rather than relying only on the generic J-FET-input description.
This page combines the device identity, verified package information, sourcing context, legacy-placement guidance, and engineering checks needed to evaluate AD515JH/+ in instrumentation systems. It is intended to help designers distinguish a true mechanical and electrical replacement from a merely similar precision op amp.
Drop-in alternatives for AD515JH/+ — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
No drop-in alternatives available for this product.
Request AlternativesAD515JH/+ Maximum Ratings & Electrical Characteristics
| Amplifier Type | Precision J-FET-input electrometer operational amplifier |
| Number of Amplifier Circuits | 1 circuit |
| Input Device Type | J-FET |
| Input Offset Voltage | 3000 uV maximum |
| Power Classification | Low-power |
| Monolithic Construction | Monolithic |
| Package Type | TO-99-8 |
| Number of Terminals | 8 terminals |
| Mounting Style | Through-hole metal can |
| Temperature Grade | Commercial |
| Terminal Form | Wire |
| Package Shape | Round |
AD515JH/+ round Pin Configuration Guide
Pin configuration for AD515JH/+ (round package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for AD515JH/+.
Refer to the datasheet for full pin configuration.
Typical Applications
AD515JH/+ is suitable for 6 applications: High-Impedance Sensor Signal Conditioning, Photodiode Current Measurement, pH and Ion-Sensitive Measurement, Capacitance and Charge Measurement, Laboratory Instrumentation, Low-Current Transducer Interface.
High-Impedance Sensor Signal Conditioning
The AD515JH/+ fits legacy high-impedance sensor front ends because it is a precision, low-power J-FET-input electrometer amplifier with one amplifier channel in an 8-lead TO-99 package. It can condition signals from resistive, capacitive, or charge-sensitive sensors while avoiding the higher input-bias-current burden associated with many bipolar-input amplifiers. The implementation should use guarded input traces, clean analog grounding, and a feedback network selected for the sensor capacitance. Input offset voltage is listed up to 3000 uV, so calibration and sensor-specific error analysis remain important.
Recommended
Photodiode Current Measurement
The AD515JH/+ is suitable for photodiode and optical-detector current measurement when low input current and high source impedance dominate the design. Its J-FET-input electrometer topology supports a single-stage transimpedance arrangement, while the TO-99-8 package provides through-hole construction for legacy laboratory and industrial instruments. The circuit must balance feedback resistance against bandwidth and photodiode capacitance, and its grounded package requires attention to case potential. Confirm input bias current, input capacitance, noise, and stability in the manufacturer datasheet before production use.
Recommended
pH and Ion-Sensitive Measurement
The AD515JH/+ can serve as the input amplifier in a legacy pH, ion-selective electrode, or electrochemical measurement system. These sensors present very high source impedance, so the amplifier’s J-FET input architecture and low-power electrometer role are important for preserving the measurement signal. Place the amplifier close to the sensor, guard sensitive nodes against leakage, and separate the analog input path from switching converters and relay transients. Input offset voltage up to 3000 uV makes calibration, reference-junction compensation, and drift control essential parts of the complete measurement design.
Recommended
Capacitance and Charge Measurement
The AD515JH/+ is appropriate for capacitance, charge, and displacement measurements that rely on a very high-impedance input stage. The single J-FET-input amplifier can be configured as a sensitive charge-to-voltage or capacitance-to-voltage circuit, with the TO-99-8 package matching established instrumentation layouts. Practical performance depends on guarding, cleanliness, insulation resistance, and careful feedback-component selection. The low-power monolithic design also helps limit self-heating, but the designer must verify noise density, bias current, bandwidth, and input overload behavior against the smallest signal of interest.
Recommended
Laboratory Instrumentation
The AD515JH/+ can support legacy laboratory instrument front ends that require a low-noise, high-impedance precision input stage. Its one-amplifier TO-99-8 construction is useful when restoring an existing analyzer, picoammeter, or general-purpose measurement module without changing the established PCB footprint. The amplifier should sit close to the input connector, with the analog return arranged to minimize pickup and ground-potential differences. Because the device is obsolete and packaged in a through-hole metal can, mechanical interchangeability, case grounding, thermal conditions, and electrical drift must be reviewed during any repair or redesign.
Recommended
Low-Current Transducer Interface
The AD515JH/+ is well aligned with low-current transducer interfaces because the J-FET-input electrometer amplifier minimizes input-bias-current effects when the source resistance is high. It can convert small transducer currents into a measurable voltage, provided the feedback network and downstream converter are selected with adequate bandwidth and dynamic range. The documented offset-voltage ceiling of 3000 uV can be significant in nanoamp-level measurements, so zero calibration and drift compensation should be included. Maintain a guarded, low-leakage layout and verify supply range, common-mode limits, and noise before approving the circuit.
Recommended
Recommended Products Summary
Engineering reference data for AD515JH/+ — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product |
|---|---|
| Package | TO-99-8 |
| Brand | Analog Devices |
| Amplifier Circuit Count | 1 circuit |
| Input Architecture | J-FET input |
| Input Offset Voltage | 3000 uV maximum |
| Power Classification | Low-power |
| Construction | Monolithic precision |
| Terminal Count | 8 terminals |
| Temperature Grade | Commercial |
| Lifecycle Status | Obsolete |
Key Differentiators
- Purpose-built precision electrometer positioning (vs AD549KHZ)
- Established through-hole implementation (vs AD549KHZ)
- Commercial-grade legacy sourcing context (vs Modern precision operational amplifiers)
Design Notes
Use the Analog Devices TO-99-8 mechanical drawing to establish the land pattern, pin-one position, and case clearance. Place the amplifier close to the input connector or sensor, keep the high-impedance node physically short, and surround that node with a grounded guard where the application permits. Do not route switching-control, display, or relay signals beside the input because capacitive coupling can overwhelm a measurement made with a high-impedance source.
Do not assume that AD549KHZ or another TO-99 precision amplifier is a drop-in replacement merely because the package outline appears similar. Verify the assignment of all eight terminals, offset-input polarity, supply pins, case connection, input bias current, noise, common-mode range, gain-bandwidth product, and slew rate. The published cross-reference information identifies similar functions but does not establish complete pin compatibility for the AD515JH/+.
Design the input stage around leakage, capacitance, and noise rather than only nominal gain. Use a feedback resistor no larger than necessary for the required sensitivity, keep feedback-loop nodes compact, and provide clean grounding around the reference return. For capacitive sensors or photodiodes, calculate the transimpedance bandwidth from feedback resistance, total input capacitance, and the amplifier’s gain-bandwidth product before selecting compensation components.
Check the dissipation and ambient-temperature limits from the Analog Devices datasheet because no power rating is stated in the product listings. Keep the metal can away from heat sources and preserve airflow around the through-hole device. When the amplifier dissipates appreciable power, use the package’s specified thermal path rather than assuming the surrounding copper area alone is adequate.
Compliance Information
The available product records do not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 qualification is not applicable to this commercial-grade precision analog amplifier unless a separate automotive qualification is documented.