ATXMEGA16C4-AN - 32MHz 16KB AVR Microcontroller | Microchip
MPN: ATXMEGA16C4-AN ✓ ActiveATXMEGA16C4-AN Overview
An AVR XMEGA microcontroller is an 8/16-bit RISC controller designed to balance processing throughput, deterministic event handling, and low-power operation. In the product hierarchy, the ATXMEGA16C4-AN belongs to the AVR XMEGA family of 8/16-bit microcontrollers, combining a compact embedded CPU with timers, serial interfaces, analog conversion functions, and programmable event-system resources. Its enhanced RISC architecture supports single-clock-cycle instruction execution for responsive control loops.
The device provides 16 KB of Flash, including a dedicated 4 KB boot-code section with read-while-write capability. It also includes 1 KB of internal EEPROM for nonvolatile configuration data and 2 KB of SRAM for working memory. Four 16-bit timer/counter modules support timing and PWM functions, while three USARTs and two TWI interfaces provide serial connectivity for sensors, human-interface equipment, and industrial control networks.
The four-channel event system is a key architectural feature for coordinating activities without relying entirely on interrupt service routines. A programmable multilevel interrupt controller organizes events by priority, and the 16-bit real-time counter provides a dedicated timekeeping resource. Together, these features are useful when several inputs must be sampled, filtered, or reacted to with predictable timing.
Typical uses include industrial control modules, sensor hubs, motor controllers, communication bridges, compact data loggers, and embedded gateways. The 34 GPIO pins make the ATXMEGA16C4-AN suitable for designs that need multiple digital interfaces without adding a separate programmable logic device. Its 32 MHz operating ceiling also supports time-sensitive protocol handling and higher-rate control tasks.
Designers should verify every signal assignment and voltage-domain connection against the manufacturer pin-description table before routing the PCB. Pay particular attention to supply pins, decoupling, programming interfaces, and any pins configured for analog functions. Confirm the device's full electrical limits, ADC performance, clock options, and absolute maximum ratings before releasing a production design.
This product page combines the manufacturer device specifications, exact-package information, practical application guidance, pin-compatible migration considerations, and engineering-focused comparison data. It is intended to support component selection, schematic review, firmware planning, and PCB footprint verification without replacing the complete manufacturer documentation.
Drop-in alternatives for ATXMEGA16C4-AN — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with ATXMEGA16C4-AN (same form factor and footprint) — differing in Package, Flash Memory, Event System Channels, Product Type, Boot Code Section.
ATXMEGA16C4-AU
✅ Drop-InContact for price
View Datasheet →ATXMEGA16C4-ANR
✅ Drop-In📋 Reference alternative (not in catalog)
ATXMEGA32C4-AU
✅ Drop-InContact for price
View Datasheet →ATXMEGA32D4-AU
✅ Drop-InContact for price
View Datasheet →ATXMEGA32A4U-AU
✅ Drop-InContact for price
View Datasheet →ATXMEGA16C4-AN Maximum Ratings & Electrical Characteristics
| Product Type | 8/16-bit RISC Microcontroller |
| Architecture | AVR enhanced RISC |
| Maximum Clock Frequency | 32 MHz |
| Flash Memory | 16 KB |
| Boot Code Section | 4 KB |
| Flash Read-While-Write | Supported |
| EEPROM | 1 KB |
| SRAM | 2 KB |
| General-Purpose I/O | 34 lines |
| Event System | 4 channels |
| Interrupt Controller | Programmable multilevel |
| Real-Time Counter | 16-bit |
| Timer/Counter Modules | 4 modules, 16-bit |
| USART Modules | 3 |
| TWI Interfaces | 2 |
| ADC | Present |
| Supply Voltage | 3.3 V |
| Package | 44-pin TQFP |
| Mounting Type | Surface mount |
ATXMEGA16C4-AN 44-pin tqfp Pin Configuration Guide
Pin configuration for ATXMEGA16C4-AN (44-pin tqfp package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for ATXMEGA16C4-AN.
Refer to the datasheet for full pin configuration.
Typical Applications
ATXMEGA16C4-AN is suitable for 6 applications: Industrial Sensor Hub, Motor Control and Actuator Interface, Communication Protocol Bridge, Data Logger and Recorder, LED and Human-Interface Controller, Battery-Powered Embedded Control.
Industrial Sensor Hub
The ATXMEGA16C4-AN fits a compact sensor hub where multiple inputs must be sampled and reported over a wired network. Its 34 GPIO lines provide ample digital interface capacity, while the four 16-bit timer/counters support periodic measurement, timeout, and PWM-related functions. The three USARTs can connect a radio or host processor, a local module, and diagnostic equipment without sharing a peripheral. The four-channel event system can coordinate sampling events and communication timing, reducing CPU polling overhead. According to the Microchip manufacturer datasheet, the device operates up to 32 MHz and provides 16 KB of Flash, 1 KB of EEPROM, and 2 KB of SRAM, making it appropriate for protocol handling, filtering, configuration storage, and local diagnostics. Engineering attention should focus on pin multiplexing and keeping communications routing away from sensitive analog traces.
Recommended
Motor Control and Actuator Interface
The ATXMEGA16C4-AN is suitable for compact actuator-control boards that combine pulse generation, status inputs, and serial command handling. Its four 16-bit timer/counter modules provide dedicated timing resources for PWM, capture, and periodic control functions, while 34 GPIO lines allow connection of drivers, switches, position sensors, and status indicators. The programmable multilevel interrupt controller helps prioritize time-sensitive events, and the four-channel event system can link timer events to communication or logic operations. At up to 32 MHz, the controller provides substantial throughput for closed-loop calculations, fault handling, and coordinated startup. According to the Microchip manufacturer datasheet, the 16 KB Flash and 1 KB EEPROM are adequate for compact control firmware and persistent parameters. The final design must include suitable driver-stage protection, fault shutdown behavior, and decoupling appropriate to the selected motor supply.
Recommended
Communication Protocol Bridge
The ATXMEGA16C4-AN can bridge legacy serial equipment to a modern embedded network because it includes three USARTs and two TWI interfaces in a single 44-pin TQFP device. One USART can serve a host console, another can connect to a local sensor or radio module, and the TWI interfaces can support local devices such as EEPROMs, sensors, or display controllers. Its four-channel event system supports deterministic routing between communication events and timers, while the programmable multilevel interrupt controller prioritizes protocol deadlines. According to the Microchip manufacturer datasheet, the device combines 32 MHz operation with 2 KB of SRAM for packet buffers and protocol state. A bridge design should budget SRAM carefully, isolate communications lines where required, and confirm peripheral multiplexing on all 44 package pins before schematic release.
Recommended
Data Logger and Recorder
The ATXMEGA16C4-AN can serve as the controller for a compact local data recorder that combines sensor inputs, nonvolatile configuration, and serial data transfer. The 16 KB Flash supports application firmware and a boot-code section, while 1 KB of EEPROM can retain calibration values, counters, or device settings. Four 16-bit timers can establish uniform sampling periods, and the programmable multilevel interrupt controller helps separate acquisition deadlines from background work. The device's three USARTs permit simultaneous use for a data destination, configuration console, and optional external sensor link. According to the Microchip manufacturer datasheet, the AVR enhanced RISC core supports responsive single-cycle instruction execution. Storage media, write endurance, clock accuracy, and power-loss recovery should be designed around the particular logger requirements rather than inferred from the MCU specifications.
Recommended
LED and Human-Interface Controller
The ATXMEGA16C4-AN fits human-interface and indicator boards that combine LED patterns, switches, displays, and serial configuration. Four 16-bit timer/counter modules can generate PWM for dimming or indicator timing, while 34 GPIO lines provide a flexible connection to keys, display segments, status LEDs, and external interface logic. The four-channel event system can coordinate button activity, display updates, and periodic events, and the two TWI interfaces can connect suitable display or sensor devices. According to the Microchip manufacturer datasheet, the MCU runs up to 32 MHz and includes a programmable multilevel interrupt controller for responsive event prioritization. For reliable human-interface behavior, debounce and update rates should be tied to the timer resources, and current limits for every LED or display path should be checked against the selected driver circuit.
Recommended
Battery-Powered Embedded Control
The ATXMEGA16C4-AN can serve as the central controller in a compact battery-powered instrument because its low-power AVR XMEGA architecture includes a 32 MHz performance ceiling, event-driven peripherals, and dedicated timing resources. The four-channel event system allows sensors, timers, and communication interfaces to coordinate work without continuous processor polling, while the programmable multilevel interrupt controller supports prioritized wake-up and fault handling. Its three USARTs and two TWI interfaces provide multiple options for connecting low-power sensors, a local display, or a host. According to the Microchip manufacturer datasheet, the device offers 16 KB of Flash, 1 KB of EEPROM, and 2 KB of SRAM. Final battery-life calculations must incorporate the selected clock mode, sleep configuration, peripheral activity, regulator efficiency, and external sensor current because those operating-mode details are not established by the headline frequency alone.
Recommended
Recommended Products Summary
Engineering reference data for ATXMEGA16C4-AN — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | ATXMEGA16C4-AU | ATXMEGA16C4-ANR | ATXMEGA32C4-AU | ATXMEGA32D4-AU | ATXMEGA32A4U-AU |
|---|---|---|---|---|---|---|
| Package | 44-pin TQFP | 44-pin TQFP | 44-pin TQFP | 44-pin TQFP | 44-pin TQFP | 44-pin TQFP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Maximum Clock Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 16 KB | 16 KB | 16 KB | 32 KB | 32 KB | 32 KB |
| EEPROM | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB |
| SRAM | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB |
| General-Purpose I/O | 34 lines | 34 lines | 34 lines | 34 lines | 34 lines | 34 lines |
| Event System | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| USART Modules | 3 | 3 | 3 | 3 | 3 | 3 |
| TWI Interfaces | 2 | 2 | 2 | 2 | 2 | 2 |
Key Differentiators
- Matches the 16C4 memory configuration without increasing Flash (vs ATXMEGA32C4-AU)
- Uses a 3.3 V supply configuration (vs ATXMEGA32D4-AU)
- Uses the exact ATXMEGA16C4-AN ordering configuration (vs ATXMEGA16C4-AU)
- Preserves the smaller 16 KB code footprint for cost-sensitive embedded designs (vs ATXMEGA32A4U-AU)
Design Notes
Use the manufacturer pin-description table to distinguish power, ground, programming, reset, analog, and multiplexed GPIO assignments before routing the 44-pin TQFP. Place the required bypass capacitors directly at the supply pins and provide short, low-impedance paths to the ground plane. Treat programming and reset nets as sensitive to switching noise, and verify exposed-pad or thermal requirements against the exact package drawing before releasing the layout.
The three USART and two TWI interfaces can make the 32 MHz TQFP design sensitive to long or poorly terminated routes. Keep clock traces short and controlled, provide suitable return paths beneath high-speed signals, and separate communication edges from ADC inputs and precision analog references. Although the four-channel event system reduces timing jitter, firmware scheduling and edge-rate assumptions must be tested with the actual clock, peripheral configuration, and external load.
Plan the 3.3 V supply path before adding communications transceivers or actuators. Separate the MCU's regulated supply from high-current loads, maintain local decoupling at the package, and calculate regulator headroom for temperature, load transient, and startup margin. The controller's 32 MHz operating ceiling does not determine power dissipation by itself; actual consumption depends on the selected clock source, active peripherals, GPIO loading, and sleep mode.
Do not treat a 44-pin TQFP package alone as proof that an alternative is a drop-in replacement. Verify the ordering suffix, power pins, boot configuration, peripheral multiplexing, voltage range, interrupt vector behavior, and programming interface. When moving from ATXMEGA16C4-AN to a 32 KB ATXMEGA variant, rebuild and test the firmware because the memory map, linker script, boot section, and application resource assumptions can change.
Compliance Information
Use the current Microchip material-compliance declaration for the exact orderable MPN. No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement appears in the source excerpts.