CS82C5496 - 8MHz Programmable Timer IC | Renesas Electronics
MPN: CS82C5496 ✓ ActiveCS82C5496 Overview
A programmable timer IC is a clock-and-timing semiconductor that generates, measures, or delays periodic events under digital control. Within the system hierarchy, it belongs to clock and timing ICs, which include oscillators, frequency dividers, timers, counters, and related timing controllers. Such devices provide a hardware alternative to software timing loops, allowing periodic events to continue deterministically while a processor handles higher-level tasks.
The CS82C5496 is intended for applications requiring programmable time intervals, event counting, retriggerable timing, or periodic waveform generation. Its 28-pin PLCC package provides a substantial number of connections compared with smaller timer packages, making it suitable for designs that need access to multiple timer channels, control signals, and bus-related functions. The exact operating limits, channel count, output behavior, voltage range, and electrical characteristics must be confirmed from the manufacturer datasheet before a production design is released.
Within the CS82C54 family, the final suffix identifies the specific ordering configuration. The verified product listing identifies CS82C5496 as the 8 MHz version in the 28-pin PLCC package. Designers should therefore treat CS82C5496 as a timing-specific family member rather than assume that every CS82C54 suffix has identical frequency, temperature, package, or lifecycle characteristics.
Typical uses include industrial machine timing, event sequencing, pulse generation, periodic sampling control, instrumentation, embedded data-acquisition systems, and legacy control equipment. In these systems, the timer can count oscillator-derived intervals, compare them with programmed values, and generate status or interrupt signals. This reduces reliance on processor polling and supports repeatable operations when response timing matters.
The main design consideration is ensuring that the clock, control, reset, and output timing meet the target system requirements. Validate maximum and minimum counter values, output pulse width, reset behavior, input levels, supply voltage, and operating temperature against the exact datasheet. PCB planning should preserve the PLCC footprint and provide adequate assembly clearances around the J-leaded package.
This product page combines the documented device identity and package information, a focused drop-in cross-reference, application guidance, comparison parameters, and practical engineering notes. It is intended to accelerate engineering review while directing final qualification decisions to the relevant manufacturer documentation and a formal procurement request.
Drop-in alternatives for CS82C5496 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with CS82C5496 (same form factor and footprint) — differing in Package Type.
CS82C54Z96
✅ Drop-InContact for price
View Datasheet →CS82C5496 Specifications
| Device Type | Programmable timer IC |
| Operating Frequency | 8 MHz |
| Timer Family | CS82C54 |
| Package Type | 28-pin PLCC |
| Package Body Size | 11.51 x 11.51 mm |
| Lead Form | J-lead |
| Mounting Type | Surface mount |
| RoHS Status | Compliant |
CS82C5496 11.51 x 11.51 mm Pin Configuration Guide
Pin configuration for CS82C5496 (11.51 x 11.51 mm package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for CS82C5496.
Refer to the datasheet for full pin configuration.
Typical Applications
CS82C5496 is suitable for 6 applications: Industrial Machine Event Sequencing, Pulse and Retriggerable Timing Control, Periodic Sampling Controller, Embedded Counter and Frequency Divider, Legacy Control Board Upgrade, Data-Acquisition Trigger Coordination.
Industrial Machine Event Sequencing
The CS82C5496 is appropriate for industrial event sequencing when the original system relies on deterministic hardware timing. Its programmable timer architecture can count oscillator-derived intervals or external events, compare them with programmed values, and generate status signals for the next stage of a machine cycle. The documented 8 MHz operating frequency supports timing calculations based on the device's actual count behavior, while the 28-pin PLCC package provides the connections required by legacy industrial control boards. Before deployment, verify supply-voltage limits, counter range, reset semantics, output timing, and operating-temperature limits against the manufacturer datasheet, because machine controls may experience supply transients, electrical noise, and long operating cycles.
Recommended
Pulse and Retriggerable Timing Control
The CS82C5496 can support pulse-width, delay, and retriggerable timing-control circuits in legacy automation and instrumentation equipment. Instead of relying on a processor loop to generate every timed transition, the timer can operate as a hardware event manager while the controller handles diagnostics and higher-level sequencing. The CS82C54 family's programmable nature allows the timing behavior to be established with external components and control logic. During implementation, confirm the available count range, minimum programmable interval, gate and trigger response, and output pulse characteristics in the datasheet, then preserve signal margins in the surrounding logic so switching noise does not cause false retriggering.
Recommended
Periodic Sampling Controller
The CS82C5496 is suitable for periodic sampling control in measurement and test systems that require repeatable acquisition intervals. Its 8 MHz operating frequency provides the timing basis for programmed count intervals, allowing a sampler, analog switch, or data-capture circuit to be enabled at a known rate. Hardware timing can reduce processor overhead and make acquisition cadence less dependent on software scheduling. The design should establish which timer output initiates each conversion and how a reset or overflow affects the schedule. Confirm output polarity, maximum count, load and count timing, and clock accuracy in the manufacturer datasheet before connecting it to precision analog front ends.
Recommended
Embedded Counter and Frequency Divider
The CS82C5496 can serve as a programmable counter or frequency divider when a legacy embedded controller must divide a clock, accumulate external events, or generate a slower periodic signal. This arrangement is useful for actuator pacing, display refresh timing, repetitive test steps, and background housekeeping in industrial electronics. The 28-pin PLCC format allows the timer to coexist with address, data, and control signals in established board layouts. Engineers should verify whether the required event source is compatible with the available count or gate inputs and whether cascaded timing is supported by the selected configuration. Accurate clock tolerance and edge timing are particularly important when the divided output serves as a measurement reference.
Recommended
Legacy Control Board Upgrade
The CS82C5496 is a practical choice when maintaining or cloning a legacy control board that already uses the CS82C5496 pin arrangement and 8 MHz timing configuration. Reusing the documented 28-pin PLCC footprint avoids introducing a package-conversion redesign, while the original-family function set supports continued use of established timing logic and software interfaces. An upgrade still requires verification of electrical compatibility, load conditions, and thermal performance because a mechanically similar device does not automatically guarantee system-level equivalence. Confirm the pin description table, supply limits, input thresholds, output drive, and timing behavior against each revision of the original equipment documentation before releasing replacement hardware.
Recommended
Data-Acquisition Trigger Coordination
The CS82C5496 can coordinate deterministic trigger events in data-acquisition and test systems where multiple measurement stages must begin at controlled intervals. A hardware timer can generate request, gate, or status signals that synchronize an analog front end, converter, or memory-control circuit without continuous processor intervention. Its 8 MHz operating frequency defines the underlying time increment, while the programmable architecture permits different interval values to be loaded for each test sequence. For high-accuracy instruments, validate oscillator accuracy, count-to-time scaling, trigger setup time, and output jitter. The timer should also be placed away from noisy switching nodes on the PCB so clock and trigger edges retain adequate noise margin.
Recommended
Recommended Products Summary
Engineering reference data for CS82C5496 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | CS82C54Z96 |
|---|---|---|
| Brand | Renesas Electronics | Intersil Corporation |
| Package | 28-pin PLCC (J-Lead), 11.51 x 11.51 mm | 28-pin PLCC (J-Lead) - same package |
| Device Type | Programmable Timer IC | Programmable Timer IC |
| Timer Family | CS82C54 | CS82C54 |
Key Differentiators
- Documented CS82C54 family identity (vs CS82C54Z96)
- Established 28-pin PLCC integration (vs CS82C54Z96)
- Cross-reference compatibility with consistent functional characteristics (vs CS82C54Z96)
Design Notes
Treat the 28-pin PLCC footprint as a controlled library component: verify pad dimensions, lead pitch, body clearance, and J-lead orientation against the package drawing before releasing artwork. Keep nearby routing clear of the package edges and provide suitable assembly and inspection clearance. Because the package library used for this page does not include a dedicated 28-pin PLCC symbol, engineers should import the manufacturer drawing into the PCB library and cross-check it against the assembled board rather than relying on a generic footprint.
Route clock and trigger nets away from switching nodes, high-current return paths, and unprotected long parallel runs. Confirm source and destination thresholds from the datasheet, add appropriate conditioning if legacy signals use different logic families, and maintain a defined return path beneath clock routes. The 8 MHz operating frequency is modest, but timing accuracy can still be affected by noise, ringing, and inappropriate propagation-delay assumptions around counter, gate, and reset inputs.
Do not select a replacement solely because its part number contains the same family name. Compare the complete pin description, supply range, timer-channel arrangement, count width, output polarity, reset behavior, timing limits, and package drawing. The documented CS82C54Z96 cross-reference is a strong starting point, but qualification should include power-up, reset, maximum-rate, output-load, and environmental testing on the target board.
Compliance Information
The manufacturer datasheet states that Pb-free products use Pb-free material sets, die-attach materials, and 100% matte-tin termination finishes, and that the products are RoHS compliant. The precise Pb-free MSL and peak-reflow classification require confirmation from the datasheet.