DG403DYZ - Dual 2:1 SPDT 45Ω Analog Switch | Renesas
MPN: DG403DYZ ✓ ActiveDG403DYZ Overview
An analog switch is an integrated semiconductor that routes electrical signals between circuit nodes under digital control. The SPDT, or single-pole double-throw, configuration connects one common terminal to one of two switched terminals. As a dual 2:1 CMOS analog switch, the DG403DYZ places two such routing elements in one package. It belongs to the broader analog-switch and multiplexer hierarchy, connecting precision measurement, test, signal-processing, and communication circuits.
Key characteristics include two switch circuits, a 45 Ω maximum on-resistance rating, switching time below 150 ns, and low charge injection suitable for sample-and-hold applications. TTL- and CMOS-compatible control inputs simplify interfacing with digital controllers. The manufacturer describes the monolithic CMOS implementation as providing low analog on-resistance and improved switching performance while retaining a standard 16-SOIC footprint.
The two independent SPDT channels allow a compact board to route control, measurement, or low-energy analog signals without using two separate switch packages. Because both channels share one IC, system designers can simplify routing logic and reduce component count. The Renesas datasheet also states that DG401 and DG403 pinouts are similar, permitting a standard layout for different switch functions, although the DG401 is SPST rather than a direct functional substitute.
Typical uses include sample-and-hold acquisition, test-equipment signal routing, data-acquisition systems, battery-powered instrumentation, and industrial control interfaces. The DG403DYZ is especially appropriate when TTL-compatible control is useful, switching speed below 150 ns is adequate, and a 45 Ω maximum on-resistance is acceptable for the signal path. Its dual-channel arrangement can simplify designs that require two coordinated or independent routing decisions.
PCB design should preserve the manufacturer's pin and footprint requirements and route each switched signal away from digital control traces where possible. Keep the analog source, drain, and common paths short, use a ground plane, and place input and output protection close to the external connector. Verify the actual signal amplitude and bandwidth against the 45 Ω on-resistance specification before using the switch in precision or high-impedance measurement paths.
This product page combines the manufacturer's DG403 family information, exact ordering-code details, source links, package guidance, comparison information, and practical selection criteria. Those engineering details help distinguish a true same-footprint replacement from a merely similar analog switch and support faster design evaluation for analog routing applications.
Drop-in alternatives for DG403DYZ — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with DG403DYZ (same form factor and footprint) — differing in Logic Compatibility, Maximum On-Resistance, Package.
DG403DY+
✅ Drop-InContact for price
View Datasheet →DG403DY-T1
✅ Drop-In📋 Reference alternative (not in catalog)
DG403DYZ Maximum Ratings & Electrical Characteristics
| Number of Circuits | 2 circuits |
| Switch Configuration | 2:1 SPDT per circuit |
| Maximum On-Resistance | 45 Ω |
| Turn-On Time | <150 ns |
| Logic Compatibility | TTL and CMOS compatible |
| Technology | Monolithic CMOS |
| Package | 16-pin SOIC |
| Number of Switches | 2 SPDT switches |
DG403DYZ 16-pin soic Pin Configuration Guide
Pin configuration for DG403DYZ (16-pin soic package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for DG403DYZ.
Refer to the datasheet for full pin configuration.
Typical Applications
DG403DYZ is suitable for 6 applications: Sample-and-Hold Acquisition, Data-Acquisition Signal Routing, Industrial Control Signal Routing, Battery-Powered Instrumentation, Test and Measurement Systems, Communication and Signal Conditioning.
Sample-and-Hold Acquisition
The DG403DYZ fits sample-and-hold front ends because its low charge injection reduces the switching disturbance injected into the holding capacitor, while turn-on time below 150 ns supports rapid acquisition sequencing. Two independent 2:1 SPDT circuits can select source signals and route the selected node without requiring two separate switch packages. The 45 Ω maximum on-resistance must be included in the source-impedance and settling-error calculation. Use the manufacturer's pin table for the 16-SOIC footprint and place the device close to the sampling node to minimize parasitic capacitance and susceptibility to control-edge coupling.
Recommended
Data-Acquisition Signal Routing
DG403DYZ is useful in compact data-acquisition systems that must route two low-energy analog channels through controlled routes. Its two SPDT channels provide independent signal selection, and the 45 Ω maximum on-resistance gives designers a defined limit for source impedance and attenuation calculations. Switching time below 150 ns is adequate for many multiplexed acquisition architectures, although high-signal-bandwidth systems must verify bandwidth and capacitance separately. The 16-SOIC package keeps routing compact, but sensitive analog traces should be separated from TTL or CMOS control nets and referenced to a solid ground plane.
Recommended
Industrial Control Signal Routing
The dual 2:1 configuration of DG403DYZ fits industrial control boards that need to switch sensor, actuator, or diagnostic signals under digital supervision. TTL-compatible control allows connection to conventional digital logic, while CMOS compatibility supports lower-voltage control environments. With a 45 Ω maximum on-resistance, the switch is best suited to low-current sensor and general-purpose routing rather than power switching. Engineers should check switch current, voltage range, leakage, and off-isolation limits in the DG403 family documentation, then place protection components close to external connectors to limit surge energy reaching the IC.
Recommended
Battery-Powered Instrumentation
DG403DYZ can be used in portable measurement equipment where two analog signals must be routed while keeping the circuit compact and control logic compatible with CMOS systems. The dual SPDT arrangement replaces two discrete switch packages, and the turn-on time below 150 ns supports rapid range or source changes. Its 45 Ω maximum on-resistance may create a measurable divider with the source impedance, so gain calculations should include the switch resistance and leakage. Low-power designs should also verify supply current, inactive-channel behavior, and power-consumption requirements in the manufacturer datasheet before finalizing the battery operating profile.
Recommended
Test and Measurement Systems
The DG403DYZ is appropriate for test-equipment signal routing where one common point must connect to one of two paths for either channel. Its two independent switches can simplify fixture routing, while the 45 Ω on-resistance limit supports many low-impedance measurement paths. Turn-on time below 150 ns helps minimize settling intervals during automated test sequences, although relay-level hold-up, bandwidth, and isolation requirements may favor a different architecture. Use a short analog path, a continuous ground plane, and controlled TTL or CMOS drive levels. Review leakage and capacitance before selecting external divider impedances or high-gain front ends.
Recommended
Communication and Signal Conditioning
DG403DYZ can route control or conditioned signal paths in communication and signal-conditioning equipment when the signal amplitude and bandwidth remain within the device's published limits. Two SPDT channels allow a single package to implement local routing or redundancy, and the monolithic CMOS design supports compact board layouts. The 45 Ω maximum on-resistance can attenuate high-impedance signals and should be included in the end-to-end transfer function. Keep switched traces short, maintain continuous ground references, and avoid routing the analog nodes beside fast digital clock lines. Control timing and propagation delay should be checked across the complete system rather than inferred from the tON value alone.
Recommended
Recommended Products Summary
Engineering reference data for DG403DYZ — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | DG403DY | DG403DY-T1 |
|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Renesas Electronics | Maxim Integrated | Vishay Intertechnology |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits |
| Switch Configuration | 2:1 SPDT per circuit | 2:1 SPDT per circuit | 2:1 SPDT per circuit |
| Maximum On-Resistance | 45 Ω | 45 Ω | 45 Ω |
| Turn-On Time | <150 ns | <150 ns | <150 ns |
| Control Logic Compatibility | TTL and CMOS compatible | TTL and CMOS compatible | TTL and CMOS compatible |
| Technology | Monolithic CMOS | Monolithic CMOS | Monolithic CMOS |
| Typical On-Resistance | 20 Ω | 20 Ω | 20 Ω |
| On-Resistance Matching | 2 Ω maximum | 2 Ω maximum | 2 Ω maximum |
Key Differentiators
- Two independent SPDT routing channels in one package (vs DG403DY)
- Fast SPDT switching for test and acquisition paths (vs DG403DY-T1)
- Defined low on-resistance class (vs DG403DY-T1)
Design Notes
Include the maximum 45 Ω on-resistance when calculating signal attenuation, especially when driving a high-impedance amplifier, sensor, or sample-and-hold capacitor. A 45 Ω source resistance can interact with the receiving input resistance to create a non-negligible voltage divider. Check the switched-node capacitance and leakage as well, because turn-on time below 150 ns does not by itself guarantee that the complete acquisition node has settled.
Follow the 16-pin SOIC land pattern and pin-description table in the Renesas DG401/DG403 datasheet. Keep the common and switched analog nodes short, provide a continuous ground plane beneath the device, and route TTL or CMOS control inputs away from sensitive analog pins. Place external protection or termination components close to the connector so surge currents and ESD events are clamped before reaching the switch.
Do not treat the similar DG401 and DG403 layouts as proof that every functional limit is interchangeable. The DG401 implements an equivalent of SPST contacts, whereas the DG403 implements an equivalent of two SPDT contacts. Confirm the switch configuration, common-node assignments, control polarity, voltage limits, and exact package drawing for the selected ordering code before reusing an existing PCB.
Compliance Information
No explicit RoHS, REACH, halogen-free, lead-free, or conflict-minerals status was identified for this ordering code. AEC-Q100 is not applicable because this is an analog switch rather than an automotive-qualified device.