LM2903BQPWRQ1 - Dual Automotive Comparator | Texas Instruments
MPN: LM2903BQPWRQ1 ✓ ActiveLM2903BQPWRQ1 Overview
A comparator is an analog semiconductor that evaluates two input voltages and produces a logic-level indication of their relationship. The differential input stage determines whether the non-inverting input is above or below the inverting input, while the open-collector output stage provides a flexible interface for pull-up resistors and digital logic. In the LM2903BQPWRQ1, the dual-channel architecture provides two independent comparator functions in one package, reducing board area when two sensing channels are required.
Key advantages include rail-to-rail input operation, a common-mode input range that includes ground, an operating supply range extending to 36 V, and open-collector outputs that can sink current from an external pull-up. The open-collector architecture is particularly useful when interfacing to TTL, CMOS, or MOS logic, or when multiple open-drain outputs need to share a bus with suitable wired-AND behavior. Automotive qualification supports its use in cost-sensitive vehicle electronics where tolerance for electrical transients and ESD events is important.
The LM2903B-Q1 generation improves several parameters relative to the earlier LM2903-Q1 family while retaining compatibility with established LM2903-family applications. Its lower offset voltage supports more accurate switching thresholds, while reduced supply and input bias currents can simplify power budgeting and high-impedance sensor interfaces. Lower propagation delay is useful in control loops and threshold-detection circuits, and the improved 2 kV ESD capability strengthens robustness at exposed connector and signal interfaces.
Typical uses include automotive battery and power-system monitoring, sensor threshold conditioning, overvoltage and undervoltage detection, window comparison, industrial control logic, and dual-level signal qualification. Because the outputs are open collector, the design must include suitable pull-up resistors when a valid high output is required. Inputs must also remain within the device's absolute maximum ratings, and unused channels require appropriate input states to prevent unstable output behavior.
Designers should verify the exact input common-mode range, differential input limits, output pull-up voltage, and timing budget against the manufacturer datasheet for the selected operating condition. Automotive systems should additionally check the required qualification, temperature grade, ESD class, and production test requirements. This page combines exact catalog information, package details, drop-in alternatives, and application-specific engineering guidance for faster component selection and PCB planning.
Drop-in alternatives for LM2903BQPWRQ1 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with LM2903BQPWRQ1 (same form factor and footprint) — differing in Number of Channels, Package.
LM2904BQPWRQ1
✅ Drop-InContact for price
View Datasheet →LM2903Q2T
✅ Drop-InContact for price
View Datasheet →LM2903BQPWRQ1 Maximum Ratings & Electrical Characteristics
| Product Type | Dual differential comparator |
| Number of Channels | 2 channels |
| Supply Voltage Range | Up to 36 V |
| Common-Mode Input Voltage | Includes ground; rail-to-rail input operation |
| Differential Input Voltage | ±38 V maximum-rated supply voltage |
| Output Type | Open-collector |
| Output Compatibility | TTL, MOS, and CMOS compatible |
| ESD Performance | Improved to 2 kV |
| Automotive Qualification | AEC-Q100 qualified |
| Package | 8-pin TSSOP |
| Mounting Type | Surface mount |
| Shipping Format | Tape and reel |
LM2903BQPWRQ1 8-pin tssop Pin Configuration Guide
Pin configuration for LM2903BQPWRQ1 (8-pin tssop package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for LM2903BQPWRQ1.
Refer to the datasheet for full pin configuration.
Typical Applications
LM2903BQPWRQ1 is suitable for 6 applications: Automotive Battery Monitoring, Overvoltage and Undervoltage Detection, Automotive Sensor Threshold Conditioning, Industrial Control and Limit Detection, Window and Range Monitoring, Motor and Actuator Control.
Automotive Battery Monitoring
The LM2903BQPWRQ1 fits automotive battery and vehicle power monitoring because it combines two differential comparator channels, operation to 36 V, and improved 2 kV ESD performance in an 8-pin TSSOP package. One channel can compare a divided battery voltage with a threshold, while the second can monitor another rail or discharge condition. Open-collector outputs support pull-up-based interfacing to a controller input. The B-generation's lower offset voltage and lower propagation delay can improve threshold repeatability and response time. Final circuit design must verify the common-mode limits, input protection needs, and automotive qualification requirements.
Recommended
Overvoltage and Undervoltage Detection
LM2903BQPWRQ1 is suitable for independent overvoltage and undervoltage supervision because its two differential channels can each compare a scaled supply signal against a reference. With operation extending to 36 V and common-mode input capability that includes ground, the comparator can monitor automotive electrical nodes when the sensing network keeps each input within its ratings. Open-collector outputs permit each channel to use its own pull-up or enter a shared fault bus. Designers should validate threshold accuracy, input overvoltage behavior, and output logic levels against the manufacturer datasheet.
Recommended
Automotive Sensor Threshold Conditioning
The LM2903BQPWRQ1 can condition two high-impedance sensor signals when the application requires simple threshold decisions rather than an amplified analog output. The B-generation's lower input bias current reduces loading on sensitive sensing networks, while lower offset voltage can improve switching-point repeatability. Rail-to-rail input operation expands the usable signal range when the sensing node approaches a supply rail. Because the outputs are open collector, external pull-up resistors define the logic-high level and control the output rise time. Confirm input bias, offset, common-mode, and propagation-delay limits for the actual sensor impedance and operating temperature.
Recommended
Industrial Control and Limit Detection
The dual-channel LM2903BQPWRQ1 supports industrial limit detection, PLC input conditioning, and simple process-control decisions. A wide 36 V operating range allows the device to work with higher-voltage control systems when signals are appropriately scaled, and two independent channels reduce the component count compared with separate single comparators. The open-collector outputs can sink current for relay, indicator, or digital-logic interfaces through suitable pull-ups and drivers. The design must prevent both differential inputs from exceeding ±38 V and must account for the non-isolated power-ground relationship in the target control system.
Recommended
Window and Range Monitoring
LM2903BQPWRQ1 can implement a two-level range monitor by assigning one comparator to an upper threshold and the other to a lower threshold, then combining their open-collector states in downstream logic. The 8-pin TSSOP package supports compact implementation, while operation to 36 V suits automotive and industrial signal ranges after suitable attenuation. Its lower propagation delay helps reduce the interval between a threshold crossing and the resulting control action. Pull-up values must be selected to balance rise time, current consumption, and the sink-current capability of the open-collector output.
Recommended
Motor and Actuator Control
The LM2903BQPWRQ1 can supervise actuator or motor-control signals by comparing feedback and reference voltages in two independent channels. It is particularly relevant in automotive systems where the wide supply range, improved 2 kV ESD performance, and automotive qualification support robust interface design. The open-collector outputs can pull down a gate-driver fault input, controller interrupt, or discrete driver stage when the monitored condition is out of range. The comparator is not a motor driver, so external transistors and protection are required; verify switching margins, pull-up voltage, and inductive transient isolation in the complete circuit.
Recommended
Recommended Products Summary
Engineering reference data for LM2903BQPWRQ1 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | LM2904BQPWRQ1 | LM2903Q |
|---|---|---|---|
| Package | 8-pin TSSOP | 8-pin TSSOP | 8-pin TSSOP family option; exact suffix requires verification |
| Brand | Texas Instruments | Texas Instruments | 3PEAK |
| Comparator Type | Dual differential comparator | Window comparator | Dual differential comparator family |
Key Differentiators
- Two independently usable differential channels (vs LM2904BQPWRQ1)
- Next-generation automotive family improvements (vs LM2903Q)
- Automotive-qualified 8-pin TSSOP order code (vs LM2903Q)
Design Notes
Treat both LM2903BQPWRQ1 channels as sharing the same supply pins. Place the device's supply-decoupling capacitor close to the power terminals and return its ground connection directly to the system ground plane. Because open-collector outputs do not source current, determine the pull-up voltage independently from the comparator supply. Confirm that the pull-up node remains within the output-pin voltage limit even during fault conditions.
Keep the two input pairs short, symmetrical, and away from switching nodes and high-current return paths. Differential threshold accuracy can be degraded by unequal input routing, shared impedance, or leakage through board contamination. If an input is unused, follow the datasheet recommendation for a defined voltage rather than leaving it floating. Provide a solid ground reference beneath the TSSOP and avoid long exposed input traces near connectors.
Do not assume that equal package dimensions establish drop-in compatibility. LM2903BQPWRQ1 uses two independent differential comparator channels, while a window comparator can assign pins differently for upper and lower reference inputs. Before replacing the part, compare every pin, output architecture, common-mode range, supply range, and reference configuration. Also confirm that the alternative order code retains the required automotive qualification and temperature grade.
Open-collector outputs require pull-up resistors and can be wired for shared fault signaling. Select the resistor so the pull-up current remains below the channel's permissible sink current while still producing an acceptable rise time at the driven capacitance. Consider whether the output node can be pulled above the comparator supply during startup or shutdown. Use the manufacturer's output ratings to set a conservative pull-up voltage.
Although the LM2903B-Q1 family improves ESD performance to 2 kV, normal ESD precautions remain necessary at exposed automotive connectors and external wiring. Keep high-energy transients away from the input traces and add protection appropriate to the actual system threat level. The comparator's 36 V operating capability is not a substitute for a dedicated surge-protection network, particularly where connected leads can experience automotive load-dump events.
Compliance Information
The LM2903B-Q1 family is identified as automotive qualified, and the B-generation provides improved 2 kV ESD performance. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not stated in the available manufacturer and distributor results.