MAX3243IPWRE4 - 3.3V 250kbps RS-232 | Texas Instruments
MPN: MAX3243IPWRE4 ✓ ActiveMAX3243IPWRE4 Overview
An RS-232 transceiver is an interface IC that converts between single-ended digital logic signals and the voltage levels used by the RS-232 standard. It belongs to the hierarchy of interface ICs, communication interfaces, serial-interface transceivers, and semiconductors. Each driver converts logic-level inputs into RS-232 outputs, while each receiver converts differential noise-resistant inputs into logic-level outputs. This bidirectional conversion supports point-to-point serial links between equipment, controllers, test systems, and peripheral modules.
The MAX3243 family operates across a 3 V to 5.5 V supply range, allowing operation from both 3.3 V and 5 V systems. Its maximum signaling rate of 250 kbps suits control links, industrial equipment, instrumentation, and legacy serial connectivity. Three driver channels and five receiver channels provide more receive capacity than transmit capacity, allowing several incoming RS-232 signals to be monitored while supporting three outbound connections. The ±15 kV HBM ESD rating adds board-level protection for exposed serial ports.
The E4 ordering suffix identifies the lead-free 28-pin TSSOP configuration shown in the product ordering information. This surface-mount package supports automated assembly while requiring careful layout around the RS-232 connector and supply rails. The device is not a modern differential serial transceiver: it is intended for point-to-point RS-232 signaling rather than RS-485 multidrop networks, USB, or differential Ethernet interfaces. Its design includes the voltage levels, slew behavior, and receiver thresholds associated with RS-232.
Typical applications include industrial control panels, barcode and labeling equipment, security and access-control systems, serial-to-embedded-controller links, test instrumentation, and point-to-point service interfaces. A design can pair the MAX3243 with a microcontroller UART for logic-side connections while using a DE/RE-style control strategy where driver outputs are intentionally disabled. The receiver count also supports monitoring several incoming alarm, status, or sensor signals through separate RS-232 sources.
For reliable implementation, place the transceiver close to the connector, keep RS-232 traces short and away from clocks or switching nodes, and provide the decoupling and protection required by the application. Decoupling capacitors should be placed adjacent to the supply and ground pins. External protection may still be needed for exposed cables because the on-chip ±15 kV HBM rating is a device-level specification rather than a guarantee of complete connector immunity.
This page combines manufacturer specifications, drop-in substitution guidance, application-focused engineering notes, and a parameter comparison organized for PCB designers and component engineers evaluating the MAX3243IPWRE4 for 3.3 V or 5 V RS-232 designs.
Drop-in alternatives for MAX3243IPWRE4 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with MAX3243IPWRE4 (same form factor and footprint) — differing in ESD Protection, Product Type, Operating Temperature Range.
MAX3243IPWRDL
✅ Drop-InContact for price
View Datasheet →MAX3243EIPWR
✅ Drop-InContact for price
View Datasheet →MAX3243IPW
✅ Drop-InContact for price
View Datasheet →SP3243EUER-L
✅ Drop-In📋 Reference alternative (not in catalog)
MAX3243IPWRE4 Specifications
| Product Type | Multichannel RS-232 line driver and receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Driver Channels | 3 |
| Receiver Channels | 5 |
| ESD Protection | ±15 kV HBM |
| Operating Temperature Range | -40°C to +85°C |
| Package | 28-pin TSSOP |
| Mounting Type | Surface mount |
| Logic Supply Compatibility | 3.3 V and 5 V systems |
| Channel Arrangement | 3 drivers and 5 receivers |
| Transceiver Count | 1 multichannel transceiver |
| Operating Temperature | -40°C to +85°C |
| Standard | RS-232 |
| ESD Test Model | Human Body Model |
MAX3243IPWRE4 28-pin tssop Pin Configuration Guide
Pin configuration for MAX3243IPWRE4 (28-pin tssop package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for MAX3243IPWRE4.
Refer to the datasheet for full pin configuration.
Typical Applications
MAX3243IPWRE4 is suitable for 6 applications: Industrial Control Panel Interface, Serial Access-Control Terminal, Embedded Equipment Service Port, Security and Surveillance Peripheral, Barcode and Labeling Equipment, Test and Measurement Equipment.
Industrial Control Panel Interface
The MAX3243IPWRE4 fits point-to-point RS-232 connections between an industrial controller and a local operator interface. Its 3 V to 5.5 V supply range permits use in either 3.3 V or 5 V embedded control systems, while the 250 kbps rate covers many panel, status, and configuration links. Three drivers support outbound commands, and five receivers can monitor separate status inputs. The -40°C to +85°C range also suits temperature-controlled industrial enclosures. Place the IC near the connector, maintain short RS-232 routes, and use external surge protection when the cable leaves the enclosure.
Recommended
Serial Access-Control Terminal
The MAX3243IPWRE4 can connect an access-control terminal, card interface, or alarm controller to a serial processor. The five receiver channels allow multiple incoming status lines to be observed, while three driver channels handle commands or acknowledgements over separate point-to-point RS-232 links. A 250 kbps maximum rate is appropriate for configuration traffic and low-speed supervisory data. The device's ±15 kV HBM ESD rating improves robustness at an accessible interface boundary, although operators and long external cables may require board-level protection beyond the transceiver itself.
Recommended
Embedded Equipment Service Port
The MAX3243IPWRE4 is useful for a service or configuration port in embedded test equipment because it translates controller UART logic into RS-232 levels and returns incoming serial responses. Its 3.3 V-compatible operation reduces the need for an additional 5 V transceiver supply, and its 28-pin TSSOP footprint supports compact assembly. The 250 kbps rate is suitable for firmware-loading and diagnostic protocols. Keep the logic-side traces away from the cable-side interface, connect a solid return path, and verify baud-rate tolerance over the selected cable length before finalizing the port design.
Recommended
Security and Surveillance Peripheral
The MAX3243IPWRE4 can connect surveillance equipment, access-control readers, or alarm modules that use point-to-point RS-232 links. Five receiver channels are valuable when several independent sensors or status devices must report into a controller, while three drivers can initiate commands. The transceiver operates from 3.3 V or 5 V logic and supports signaling up to 250 kbps, which is appropriate for supervisory communication. The ±15 kV HBM protection rating is useful near exposed connectors, but outdoor installations still require enclosure design, cable protection, surge suppression, and proper grounding.
Recommended
Barcode and Labeling Equipment
The MAX3243IPWRE4 can bridge a low-power embedded controller to a barcode scanner, label printer, or other RS-232 peripheral. The 3 V to 5.5 V operating range supports compact industrial peripherals, and the 250 kbps signaling rate is sufficient for command and status traffic. The three-driver, five-receiver arrangement allows several peripherals or status lines to share the logic side of the design while remaining point-to-point on the RS-232 side. Maintain controlled cable lengths, provide a common signal ground, and place connector-side protection close to the transceiver pins.
Recommended
Test and Measurement Equipment
The MAX3243IPWRE4 suits legacy test instruments and automated measurement systems that expose an RS-232 service or control interface. Its 250 kbps maximum rate supports command exchange and result transfer, while the separate three-driver and five-receiver channels provide flexible point-to-point connectivity. The device can run from 3.3 V or 5 V instrumentation logic, helping simplify power architecture. For laboratory use, place the transceiver near the connector, maintain separation from high-impedance analog inputs, and use appropriate grounding to avoid injecting cable transients or ground-current disturbances into the measured circuit.
Recommended
Recommended Products Summary
Engineering reference data for MAX3243IPWRE4 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | MAX3243IPWR | MAX3243EIPWR | MAX3243IPW | SP3243EUER-L |
|---|---|---|---|---|---|
| Package | 28-TSSOP | 28-TSSOP | 28-TSSOP | 28-TSSOP | 28-TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Exar |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps | 250 kbps | 250 kbps |
| Driver Channels | 3 | 3 | 3 | 3 | 3 |
| Receiver Channels | 5 | 5 | 5 | 5 | 5 |
| Interface Standard | RS-232 | RS-232 | RS-232 | RS-232 | RS-232 |
Key Differentiators
- Five receiver channels support multi-input monitoring (vs SP3243EUER-L)
- Single IC supports 3.3 V and 5 V logic systems (vs MAX3243EIPWR)
- Exact E4 ordering configuration for compact TSSOP assembly (vs MAX3243IPWR)
Design Notes
Place the MAX3243IPWRE4 close to the RS-232 connector and keep connector-side driver and receiver routes short. Separate logic-side UART traces from cable-side RS-232 traces where possible, and route ground as a continuous return path. A solid ground reference and controlled physical cable routing reduce susceptibility to common-mode noise and prevent external transients from coupling directly into sensitive logic circuitry.
Do not assume that the ±15 kV HBM rating eliminates the need for external port protection. HBM testing does not represent every cable-borne surge, and a long outdoor cable can expose the interface to much larger energy. Select protection devices with suitable capacitance, standoff voltage, clamping behavior, and RS-232 signal compatibility, and confirm that added protection does not distort the 250 kbps signaling.
Connect the supply bypass capacitor directly between the power and ground pins, with a short and low-inductance path. Keep the capacitor connection short enough to suppress supply transients generated when the internal transmitter changes state. Use a quiet source for the transceiver when receiver sensitivity or logic-noise margin is important, and avoid sharing high-current return paths between the RS-232 ground and switching power stages.
Treat each RS-232 connection as a point-to-point interface and verify signal amplitude, slew behavior, receiver thresholds, baud rate, and cable capacitance together. The 250 kbps maximum rate does not guarantee reliable communication at every cable length. Use the manufacturer's test conditions and receiver specifications to establish a margin, and avoid adding excessive filtering or protection capacitance directly to driver outputs.
Compliance Information
The E4 ordering suffix identifies the lead-free configuration, but no explicit RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals declaration was identified in the supplied manufacturer and distributor information.