MSP430F2003IPW - 16MHz Low-Power MCU | Texas Instruments
MPN: MSP430F2003IPW ✓ ActiveMSP430F2003IPW Overview
A mixed-signal microcontroller combines a digital processor, analog measurement circuitry, and communication peripherals in one device. The MSP430 belongs to the MCU, RISC, embedded-controller, and semiconductor hierarchies. Its 16-bit RISC CPU, 16-bit registers, and low-power operating modes make it useful for portable measurement systems where energy efficiency and deterministic sensor acquisition are more important than large memory capacity or high multimedia processing capacity.
The MSP430F2003IPW combines a 16 MHz clock, a 16-bit sigma-delta ADC, and USI-based serial connectivity in a compact 14-pin TSSOP. Its 1 KB Flash configuration supports firmware storage in small embedded products, while 128 bytes of RAM provides working space for acquisition, filtering, and control routines. The device also offers five low-power modes according to the manufacturer product description, allowing the CPU and peripherals to remain responsive while reducing consumption between measurements.
The MSP430 architecture is centered on a 16-bit RISC core with 16-bit registers and constant-memory instructions. The USI provides a practical interface for sensors, converters, and external memory using either SPI or I2C. The sigma-delta ADC supports analog sensing in cost-sensitive industrial, instrumentation, and portable measurement products. Because the exact ADC resolution mode, conversion timing, and channel count depend on the device configuration, engineers should use the MSP430F2003 manufacturer datasheet when defining gain, sampling, and reference settings.
Typical uses include low-power sensor transmitters, industrial process-monitoring nodes, compact data loggers, portable measurement instruments, digital thermometers, and connected analog-control products. A board-level design can place the MCU close to the sensor, use the USI for a serial sensor or digital interface, and activate a low-power mode between samples. This arrangement reduces wiring and may simplify enclosure design compared with a discrete processor, analog front end, and communications interface.
The main design constraint is limited memory. Firmware, constants, acquisition buffers, and communication state must be planned carefully within 1 KB of Flash and 128 bytes of RAM. Keep analog routing compact, observe all decoupling and grounding recommendations, and validate startup, conversion timing, and serial timing in the assembled board. This page also organizes package, sourcing, and replacement information to support a faster engineering decision.
The MSP430F2003IPW is centered on the MSP430F2xx family and is suited to designs that need low-power operation, a sigma-delta ADC, and compact serial connectivity. Engineers evaluating alternatives should compare memory capacity, ADC implementation, clock requirements, package dimensions, and firmware ecosystem in addition to headline processor speed. For new designs, the 16 MHz device offers a focused feature set for embedded sensing without the resource demands of a larger general-purpose MCU.
Drop-in alternatives for MSP430F2003IPW — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with MSP430F2003IPW (same form factor and footprint) — differing in Package, SRAM, ADC Resolution, Supply Voltage, CPU Architecture.
MSP430F2001IPW
✅ Drop-In ⚠️ Specs Unverified📋 Reference alternative (not in catalog)
MSP430F2002IPW
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →MSP430F2012IPW
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →MSP430F2013IPW
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →MSP430F2101IPW
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →MSP430F2003IPW Maximum Ratings & Electrical Characteristics
| CPU Architecture | 16-bit RISC |
| Maximum Clock Frequency | 16 MHz |
| Register Width | 16 bit |
| ADC Quantity | 1 ADC |
| ADC Resolution | 16-bit sigma-delta |
| Universal Serial Interface | 1 USI supporting SPI and I2C |
| Flash Memory | 1 KB |
| RAM | 128 bytes |
| Low-Power Modes | 5 modes |
| Supply Voltage | 2.5 V to 3.3 V |
| Operating Temperature Range | -40 °C to +85 °C |
| Temperature Grade | Industrial |
| Package | 14-pin TSSOP (PW) |
| Mounting Type | Surface mount |
| Lead Count | 14 pins |
| Package Shape | Rectangular |
| Terminal Style | Gull wing |
MSP430F2003IPW rectangular Pin Configuration Guide
Pin configuration for MSP430F2003IPW (rectangular package). This digital IC includes GPIO, communication interfaces (UART, SPI, I2C), and power pins. Refer to the manufacturer datasheet for alternate pin functions and configuration options. Essential for embedded system design and PCB layout.
No detailed pinout data available for MSP430F2003IPW.
Refer to the datasheet for full pin configuration.
Typical Applications
MSP430F2003IPW is suitable for 6 applications: Portable Temperature and Environmental Sensors, Battery-Powered Process Monitoring, Compact Data Loggers, Industrial Control and Monitoring, Digital Thermometers and Measurement Instruments, Portable Medical and Wearable Monitoring.
Portable Temperature and Environmental Sensors
The MSP430F2003IPW fits compact environmental sensors that combine slow-changing measurements with low-frequency serial reporting. Its 16-bit sigma-delta ADC can acquire an analog sensor signal, while the USI can connect a digital temperature, humidity, pressure, or air-quality sensor through SPI or I2C. At 16 MHz, the 16-bit RISC core can execute filtering, calibration, threshold logic, and communication routines without a separate processor. The five low-power modes support duty-cycled measurement, while 1 KB of Flash and 128 bytes of RAM require compact firmware and carefully sized buffers.
Recommended
Battery-Powered Process Monitoring
The MSP430F2003IPW is suitable for remote process-monitoring nodes that measure one or more slow analog variables and report results over a serial link. The ADC supports direct acquisition, the USI provides SPI or I2C connectivity, and the five low-power modes reduce activity between samples. A 2.5 V to 3.3 V operating range also simplifies integration with low-energy industrial sensors. Firmware should use interrupt-driven conversion, avoid unnecessary polling, and place the controller into its lowest acceptable standby mode to preserve battery life between measurement intervals.
Recommended
Compact Data Loggers
The MSP430F2003IPW can serve as the control core of a compact data logger when measurements are acquired periodically and stored or transmitted through a serial interface. Its 16-bit RISC architecture supports timestamp handling, simple scaling, and sensor conditioning, while the USI can communicate with external nonvolatile memory or a radio module. The 128-byte RAM limit requires streaming or page-oriented data handling rather than large in-memory buffers. Developers should use the 1 KB Flash capacity carefully and make the firmware layout modular so logging and communication functions can be updated independently.
Recommended
Industrial Control and Monitoring
The MSP430F2003IPW is appropriate for small industrial control modules that monitor sensors and operate limited actuators through an external driver interface. Its integrated ADC handles analog process conditions, and the USI supports communication with isolated sensors, converters, or expansion logic. The industrial temperature range of -40 °C to +85 °C supports equipment operating across conventional industrial environments. Robust implementation still requires transient protection, proper grounding, watchdog strategy, and careful validation of ADC timing and serial communication under electrical noise.
Recommended
Digital Thermometers and Measurement Instruments
The MSP430F2003IPW can implement a digital thermometer or compact measurement instrument where a sigma-delta ADC, calibrated scaling, and serial output are required. Its 16-bit ADC path suits sensors that produce a slowly changing analog voltage, while the USI can connect a display or configuration interface through I2C. The low-power architecture allows the instrument to wake for a measurement, convert and display the result, then return to a low-power state. Calibration coefficients and display formatting must be kept compact because Flash memory and RAM are limited.
Recommended
Portable Medical and Wearable Monitoring
The MSP430F2003IPW can support low-energy wearable or portable monitoring prototypes that combine an analog vital or environmental measurement with serial sensor data. Its small TSSOP package, 2.5 V to 3.3 V operation, and five low-power modes suit space-constrained designs. The ADC and USI allow measurement acquisition and sensor communication in one controller, reducing component count. Medical use requires application-specific validation, isolation where appropriate, electrical-safety review, and software risk controls; the MCU qualification alone does not establish compliance for a finished medical product.
Recommended
Recommended Products Summary
Engineering reference data for MSP430F2003IPW — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | MSP430F2001IPW | MSP430F2002IPW | MSP430F2012IPW | MSP430F2013IPW | MSP430F2101IPW |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | TSSOP-14 (PW) | TSSOP-14 (PW) | TSSOP-14 (PW) | TSSOP-14 (PW) | TSSOP-14 (PW) | TSSOP-14 (PW) |
| Maximum Clock Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| CPU Architecture | 16-bit RISC | 16-bit RISC | 16-bit RISC | 16-bit RISC | 16-bit RISC | 16-bit RISC |
| Flash Memory | 1 KB | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB |
| RAM | 128 bytes | 256 bytes | 256 bytes | 256 bytes | 256 bytes | 256 bytes |
Key Differentiators
- Focused low-power mixed-signal integration (vs MSP430F2013IPW)
- Documented serial connectivity in a compact MCU (vs MSP430F2101IPW)
- Industrial temperature target with low-voltage operation (vs MSP430F2002IPW)
Design Notes
Calculate the complete sleep-mode current, including the MCU, ADC circuitry, voltage regulator, and external sensors. The MSP430F2003IPW can operate from 2.5 V to 3.3 V and has five low-power modes, but system standby current may be dominated by sensors or regulator leakage. Use interrupt-driven sampling, disable unused peripherals, and place the device into a low-power state only after confirming that serial communication and data retention requirements remain satisfied.
Follow the Texas Instruments manufacturer datasheet layout guidance for the 14-pin PW TSSOP, particularly for supply decoupling, analog input routing, and ground connections. Place decoupling capacitors close to their associated supply pins and keep analog traces short and away from switching nodes and high-current return paths. A compact 16-bit sigma-delta ADC can benefit from careful reference and signal routing, so validate the assembled layout with noise and conversion-stability measurements.
Do not treat a related MSP430F2xx device as interchangeable until its pin table, ADC configuration, clock requirements, memory map, and USI functions have been checked. The MSP430F2003IPW has only 1 KB of Flash and 128 bytes of RAM, so stack-heavy or buffered routines can exhaust memory. Use compiler stack analysis, avoid recursive call paths, and verify that any alternative with more memory still preserves the original board's voltage and peripheral connections.
Define USI clocking and bus timing from the device's documented operating conditions rather than assuming full-speed SPI or I2C compliance in every mode. Account for signal rise and fall times, pull-up requirements, capacitance, and the timing margin of connected sensors. For the sigma-delta ADC, validate acquisition timing, reference stability, input range, and digital filtering with the actual sensor source because external signal conditioning can dominate the final measurement accuracy.
Compliance Information
Compliance status was not identified for the exact MSP430F2003IPW ordering code. Review current manufacturer environmental declarations, material declarations, and product-quality records for the applicable regional market.