SI3010-F-GS - 16-SOIC Telecom DAA Interface IC | Skyworks
MPN: SI3010-F-GS ✓ ActiveSI3010-F-GS Overview
A Direct Access Arrangement is a telecom interface function that provides the physical line-side interface between a customer premises telephone network and a modem or embedded communications system. In the broader electronics hierarchy, a DAA belongs to the line-interface IC family, the interface-IC category, and ultimately the semiconductor and communications-equipment ecosystem. The SI3010 series is associated with Silicon Labs' Si2401 and Si2404 ISOmodem families and is intended for designs requiring a dedicated line-side interface companion IC.
The SI3010-F-GS is identified as a 16-SOIC surface-mount part. Operating-temperature information is listed as 0°C to 70°C for one catalog representation, while the manufacturer identity is shown as Silicon Labs in some records and Skyworks Solutions, Inc. in current distributor records. The GS suffix is associated with a lead-free packaging designation in the available catalog descriptions. The -F family is specifically described as the line-side DAA for the Si2404 ISOmodem.
The device is suitable for embedded voice and data terminal designs, digital subscriber line equipment, industrial telephone interfaces, and legacy telecom equipment requiring a dedicated DAA function. Because the SI3010 is a line-side interface rather than a general-purpose logic IC, its external implementation must follow the manufacturer's recommended DAA circuit, including the specified protection, isolation, and line-interface components.
The principal design consideration is footprint continuity. The SI3010-F-GS uses a 16-SOIC outline, so any replacement must preserve the same lead arrangement and electrical function. Pin assignments, absolute maximum ratings, hook-state timing, line impedance, and recommended external components should be checked against the manufacturer datasheet before schematic capture or PCB release.
The SI3010-F-GS is listed in telecom-interface catalogs with inventory and ordering information. Its package, series, and interface function make it especially relevant to maintenance, redesign, and legacy-ISOmodem projects. For a new design, confirm current lifecycle status and obtain the authoritative datasheet before committing the component to a production BOM.
This product summary consolidates the catalogued line-side DAA function, 16-SOIC package, associated Si2404 ISOmodem application, and traceable manufacturer and distributor references into an engineer-oriented resource. It also distinguishes the DAA function from general-purpose interface ICs and highlights the package and lifecycle checks that matter when replacing the part in telecom hardware.
Drop-in alternatives for SI3010-F-GS — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with SI3010-F-GS (same form factor and footprint) — differing in Mounting Type, Package, Product Type.
SI3010-F-FS
✅ Drop-InContact for price
View Datasheet →SI3010-F-FSR
✅ Drop-In📋 Reference alternative (not in catalog)
SI3010-FS
✅ Drop-InContact for price
View Datasheet →SI3010-F-GS Specifications
| Product Type | Telecom Interface IC / Direct Access Arrangement |
| Series | SI3010 |
| Associated ISOmodem | Si2401 / Si2404 |
| Functional Description | Line-side DAA for the Si2404 ISOmodem |
| Package | 16-SOIC (0.154 in, 3.90 mm width) |
| Mounting Type | Surface mount |
| Supply Voltage | 3.0 V to 3.6 V |
| Operating Temperature | 0°C to 70°C |
| Interface Type | Parallel, SPI, UART |
| Number of Circuits | 1 circuit |
| Lead-Free Status | Lead-free |
| Tube Packaging | Tube |
| Product Status | Active |
SI3010-F-GS 16-soic (0.154 in, 3.90 mm width) Pin Configuration Guide
Pin configuration for SI3010-F-GS (16-soic (0.154 in, 3.90 mm width) package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for SI3010-F-GS.
Refer to the datasheet for full pin configuration.
Typical Applications
SI3010-F-GS is suitable for 6 applications: Si2404 ISOmodem Line Interface, Embedded Voice Terminal, Digital Subscriber Line Terminal, Industrial Telephone Gateway, Legacy Telecom Equipment Maintenance, Telephone Network Test Equipment.
Si2404 ISOmodem Line Interface
The SI3010-F-GS is intended to provide the line-side Direct Access Arrangement required by a Si2404 ISOmodem implementation. Its 16-SOIC footprint allows the DAA to be placed beside the modem circuitry on a conventional surface-mount PCB, while the 3.0 V to 3.6 V supply range aligns with the associated 3.3 V modem electronics. The external telephone-line protection and network components remain essential; following the manufacturer reference circuit is necessary to preserve signal quality, hook-state control, and isolation behavior.
Recommended
Embedded Voice Terminal
An embedded voice terminal can use the SI3010-F-GS as the line-side interface companion for an ISOmodem-based design. The 16-SOIC package supports compact surface-mount assembly, and the 0°C to 70°C catalog range suits indoor commercial terminal equipment. Because this is a telephone-line DAA rather than a general-purpose transceiver, the design must implement the prescribed line protection and isolation network and validate hook-state timing against the target modem firmware.
Recommended
Digital Subscriber Line Terminal
The SI3010-F-GS is applicable to DSL terminal equipment requiring a dedicated direct-access-arrangement function in the telephone-line path. Its single-DAA architecture and 16-SOIC package allow a straightforward surface-mount layout, while the 3.0 V to 3.6 V operating supply integrates with a 3.3 V modem subsystem. System-level compliance depends on the complete protection, isolation, line-driver, and hook-state implementation rather than on the interface IC alone.
Recommended
Industrial Telephone Gateway
Industrial gateways can use the SI3010-F-GS when an embedded ISOmodem needs a dedicated line-side DAA in a 16-SOIC footprint. The 3.0 V to 3.6 V supply suits conventional 3.3 V logic, and the 0°C to 70°C range is appropriate for controlled indoor equipment. For a gateway installed in a wider thermal range, verify environmental requirements and use an appropriately qualified component rather than relying on the standard commercial-temperature grade.
Recommended
Legacy Telecom Equipment Maintenance
The SI3010-F-GS supports maintenance and redesign of legacy Si2404 ISOmodem-based telephone equipment where an existing board uses a 16-SOIC DAA position. The exact ordering code and line-side DAA function allow engineers to preserve the established board architecture when repairing populated assemblies. Before substitution, compare the -F-GS pin table, external network, supply limits, and suffix definitions with the original assembly documentation and the current manufacturer datasheet.
Recommended
Telephone Network Test Equipment
The SI3010-F-GS can serve in line-interface test equipment built around an Si2401 or Si2404 ISOmodem architecture. A dedicated DAA permits controlled interaction between the modem and the telephone network, and the surface-mount 16-SOIC package simplifies instrument-board assembly. Test-equipment developers should preserve the manufacturer-defined protection and isolation structure and account for line-side transients that can exceed the modem-side 3.0 V to 3.6 V supply limits.
Recommended
Recommended Products Summary
Engineering reference data for SI3010-F-GS — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | SI3010-F-FS | SI3010-F-FSR | SI3010-FS |
|---|---|---|---|---|
| Package | 16-SOIC (0.154", 3.90 mm Width) | 16-SOIC (0.154", 3.90 mm Width) | 16-SOIC (0.154", 3.90 mm Width) | 16-SOIC (0.154", 3.90 mm Width) |
| Brand | Skyworks Solutions, Inc. | Skyworks Solutions, Inc. | Skyworks Solutions, Inc. | Skyworks Solutions, Inc. |
| Product Type | Telecom Interface IC / Direct Access Arrangement | Line-side DAA for Si2404 ISOmodem | Line-side DAA for Si2404 ISOmodem | Telecom Interface IC / Direct Access Arrangement |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount |
Key Differentiators
- Exact GS ordering code with a documented line-side DAA function (vs SI3010-F-FSR)
- Commercial-temperature SI3010-F family positioning (vs SI3010-FS)
- Direct association with Si2401 and Si2404 ISOmodem designs (vs SI3010-F-FS)
Design Notes
Assign the board layout from the exact SI3010-F-GS 16-SOIC pin-description table in the manufacturer datasheet. Keep the DAA and its associated line-network components away from noisy modem and switching-supply areas, route the telephone-line side as a high-impedance protected network, and preserve the recommended component placement around the ISOmodem interface. The available catalog confirms the package outline but does not provide the complete pin assignment.
Design the modem-side supply for 3.0 V to 3.6 V and decouple it locally according to the manufacturer reference circuit. The DAA operates beside sensitive line-interface electronics, so supply return paths and ground currents should not share noisy switching-node paths. Verify line-side protection components separately because telephone transients are outside the modem-side supply range.
Do not select a replacement solely because the package is called 16-SOIC. Compare the exact ordering-code row, function, pin table, temperature range, qualification, and packing format across SI3010-F-GS, SI3010-F-FS, SI3010-F-FSR, and SI3010-FS. Preserve the manufacturer-defined line protection, isolation, and hook-state network; a footprint-compatible IC with incorrect suffix characteristics can still prevent functional equivalence.
Keep the telephone-line network physically separate from low-level modem signals and use the shortest practical high-impedance routing shown in the reference design. Maintain consistent grounding according to the isolation strategy, minimize return loops, and validate hook-state transitions under worst-case line conditions. Complete EMI and ESD validation at the assembled board level because the DAA is connected to external telephone wiring.
Compliance Information
The SI3010-F-GS is identified as a lead-free part in distributor records. RoHS, REACH, AEC-Q100, halogen-free, and conflict-minerals status were not explicitly established and remain unknown.