Microcontroladores

ATSAM4LS2AA-AU

ATSAM4LS2AA-AU - 48MHz Cortex-M4 128KB Flash MCU | Microchip

The Microchip Technology ATSAM4LS2AA-AU is a 32-bit ARM Cortex-M4 flash microcontroller running at up to 48MHz with 128KB of embedded Flash and 32KB of SRAM, housed in a 48-pin TQFP surface-mount package and supplied at 3.3V. A microcontroller (MCU) is a single-chip computer that integrates a processor core, memory, and programmable peripherals into one integrated circuit, sitting at the device level of the embedded systems hierarchy (semiconductor -> integrated circuit -> microcontroller -> ARM-based flash MCU). The SAM4L series belongs to Microchip's (formerly Atmel's) ARM Cortex-M family, which uses the widely supported ARMv7E-M instruction set and toolchain ecosystem. The defining strength of the ATSAM4LS2A is ultra-low power consumption: it achieves 90uA/MHz in active mode, 1.5uA in sleep mode, and the shortest wake-up time in a Cortex-M4 device at down to 1.5us, according to the Microchip product page. On-board features include a USB device controller, a peripheral event system that routes signals between peripherals without CPU intervention, and the SleepWalking capability that lets peripherals wake the CPU only when needed. Mouser lists the part as green, industrial temperature, with crypto support. Architecturally, the Cortex-M4 core provides single-cycle multiply and hardware divide with deterministic interrupt handling, well suited to real-time battery-operated firmware. The 128KB Flash accommodates application code plus over-the-air update headroom, while 32KB SRAM supports buffers for communication stacks. Typical applications include battery-powered sensor nodes, portable medical monitoring devices, utility metering, and low-power industrial end points where wake-up latency and sleep current dominate battery life calculations. Design consideration: minimize active duty cycle by exploiting SleepWalking so peripherals service events autonomously; every 1MHz of avoided active time saves roughly 90uA. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $5,39 Em estoque

ATSAM4LS2AA-AUR

ATSAM4LS2AA-AUR - 48MHz Cortex-M4 MCU 128KB Flash | Microchip

The Microchip Technology ATSAM4LS2AA-AUR is a 32-bit ARM Cortex-M4 Flash microcontroller running at up to 48 MHz with 128KB (128K x 8) of embedded Flash, housed in a 48-pin TQFP (7x7 mm) package. A microcontroller (MCU) is a single-chip embedded computer that integrates a processor core, memory, and peripherals on one die, sitting at the device level of the embedded systems hierarchy (MCU -> microcontroller -> embedded processor -> semiconductor). The SAM4L family belongs to the ARM Cortex-M class of 32-bit RISC MCUs, widely used in low-power embedded design. The headline feature of the ATSAM4LS2A is class-leading energy efficiency: 90 uA/MHz in active mode, 1.5 uA in sleep mode, and wake-up times down to 1.5 us, the shortest wake-up time among Cortex-M4 devices per Microchip's product page. It integrates a USB device controller, a peripheral event system allowing peripherals to interact without CPU intervention, and the SleepWalking capability that lets peripherals operate and wake the core only when needed. Hardware crypto support and MRL A status are listed by Mouser for this industrial-temperature, green TQFP part. Typical applications include battery-powered IoT sensor nodes, portable medical devices, industrial sensor interfaces, and consumer products requiring USB connectivity with long battery life. The Cortex-M4 core with DSP instructions handles signal processing locally, while the event system keeps dynamic power low. Design-wise, exploit SleepWalking and the peripheral event system to keep the CPU in sleep states; wake-up latency of 1.5 us makes aggressive duty-cycling practical even for event-driven tasks. This page adds distributor pricing comparison, drop-in alternatives, design notes, and FAQ content synthesized beyond the manufacturer datasheet.

USD $1,58 Em estoque

ATSAM4LS2AA-MU

ATSAM4LS2AA-MU - 48MHz Cortex-M4 MCU 128KB Flash QFN-48 | Microchip

The Microchip Technology ATSAM4LS2AA-MU is a 32-bit ARM Cortex-M4 flash microcontroller running at 48 MHz with 128 KB of embedded Flash, 32 KB of SRAM, and an integrated USB device controller, housed in a 48-pin QFN (7x7 mm) package with exposed pad. A microcontroller unit (MCU) is a single-chip embedded processor that integrates a CPU core, program memory, data memory, and peripheral functions such as timers, communication interfaces, and analog blocks. The SAM4L family sits within Microchip's (formerly Atmel) 32-bit ARM-based MCU portfolio, which spans from the low-power SAM L and SAM D families up to high-performance SAM E parts with floating-point units. MCUs are the top-level building block of embedded systems, powering industrial control, consumer devices, and IoT nodes. The defining feature of the ATSAM4LS2AA-MU is class-leading power efficiency: 90 uA/MHz in active mode, 1.5 uA in sleep mode, and wake-up times down to 1.5 us, which Microchip identifies as the lowest power and fastest wake-up among Cortex-M4 devices. The SAM4L architecture adds a Peripheral Event System and SleepWalking, allowing peripherals to operate and respond autonomously while the CPU core remains in low-power sleep. Peripherals include USB device, USART, TWI (I2C), SPI, 12-bit ADC, DAC, capacitive touch support (Peripheral Touch Controller), and an AES/DES cryptographic engine on some family members. The Cortex-M4 core delivers DSP-oriented instructions for efficient digital filtering and control-loop mathematics at 48 MHz. Typical applications include battery-powered sensor nodes, portable medical instruments, low-power IoT endpoints, and touch-sensing human interface devices where sleep current and wake-up latency dominate battery life. Design consideration: the 48-QFN exposed-pad package requires a solid ground connection through the PCB thermal pad; use via stitching to the ground plane for both thermal dissipation and signal-integrity during EMI testing. This page synthesizes distributor pricing, drop-in alternatives within the SAM4L family, and practical design notes not found in the manufacturer datasheet.

USD $3,55 Em estoque

ATSAM4LS2AA-MUR

ATSAM4LS2AA-MUR - 48MHz Cortex-M4 128KB Flash MCU | Microchip

The Microchip Technology ATSAM4LS2AA-MUR is a 32-bit ARM Cortex-M4 Flash microcontroller running at 48 MHz with 128KB embedded Flash and 32KB SRAM, housed in a 48-pin QFN (7x7 mm) exposed-pad package rated for industrial temperature ranges. A microcontroller (MCU) is a single-chip computer that integrates a processor core, program memory, data memory, and peripherals onto one die, serving as the lowest layer of the embedded-system hierarchy (MCU -> embedded processor -> system-on-chip -> computing system). The SAM4L series sits within Microchip's (formerly Atmel's) ARM-based Flash MCU portfolio, which spans the SAM3, SAM4, and SAM D/L/C families. As a Cortex-M4 class device, it combines 32-bit RISC processing with deterministic interrupt handling suited to real-time control. The defining strength of the ATSAM4LS2AA-MUR is ultra-low power: Microchip specifies 90 uA/MHz in active mode, 1.5 uA in sleep mode, and wake-up times as short as 1.5 us, the lowest figures among Cortex-M4 Flash MCUs. Integrated peripherals include a USB device controller, a peripheral event system, and the SleepWalking feature, which lets peripherals wake the core only when a programmed event occurs, minimizing CPU active time. Architecturally, the Cortex-M4 core delivers single-cycle multiply and hardware divide with a nested vectored interrupt controller (NVIC), while the 128KB Flash supports in-system programming. The peripheral event system routes signals between peripherals without CPU intervention, and low-power techniques such as dynamic clock gating reduce consumption in duty-cycled designs. Typical applications include battery-powered sensor nodes, portable medical instruments, low-power industrial sensing, and USB-connected handheld devices where 90 uA/MHz active current and 1.5 uA sleep current directly extend battery life. Design consideration: the 48-QFN exposed pad must be soldered to a grounded PCB thermal pad for reliable grounding and heat dissipation; supply is a single 3.3V rail per the datasheet. This page synthesizes distributor pricing context, drop-in family alternatives, and low-power design notes not found in the manufacturer datasheet.

USD $2,98 Em estoque

ATSAM4LS2BA-MU

ATSAM4LS2BA-MU - 48MHz Cortex-M4 MCU 128KB Flash | Microchip

The Microchip Technology ATSAM4LS2BA-MU is a 32-bit ARM Cortex-M4 microcontroller running at 48 MHz with 128KB of Flash memory and 32KB of SRAM, housed in a 64-pin VQFN (9x9 mm) package with exposed pad. Formerly an Atmel part, this SAM4L series MCU integrates picoPower technology for ultra-low-power operation in industrial temperature ranges. A microcontroller unit (MCU) is a single-chip embedded computer that combines a processor core, memory, and peripherals into one integrated circuit. Within the embedded systems hierarchy, the SAM4L sits in the mainstream ARM Cortex-M class of flash microcontrollers, positioned above entry-level Cortex-M0+ devices and below high-performance Cortex-M7 parts. MCUs are the building blocks of modern embedded electronics, from consumer devices to industrial automation controllers. Key differentiating features include the 48 MHz ARM Cortex-M4 core with DSP instructions, 128KB of single-cycle Flash program memory, 32KB of SRAM, and the picoPower technology platform that enables microamp-level sleep currents. Peripherals typically include USART, SPI, I2C (TWI) interfaces, an ADC, timers, and a USB-capable architecture, allowing a single chip to handle sensing, control, and communication duties in one package. Technically, the SAM4L series is built around the Atmel (now Microchip) low-power flash process with an ARMv7E-M based core supporting hardware multiply and digital signal processing instructions. The peripheral event system allows peripherals to communicate directly without CPU intervention, further reducing active power consumption. Multiple sleep modes with state retention let designers trade wake-up latency against standby current to match application power budgets. Typical applications include battery-powered industrial sensors and meters, portable medical monitoring devices, low-power human interface and touch sensing products, and general-purpose industrial control boards where a 3.3V, 48MHz controller with generous Flash is required. When designing with this device, budget the 9x9 mm VQFN exposed pad for good ground and thermal connection to the PCB, and validate the industrial temperature rating against your worst-case enclosure conditions. This page adds value beyond the datasheet by consolidating distributor pricing, drop-in family alternatives, comparison tables, and practical design notes in one AI-citable reference.

USD $3,79 Em estoque

ATSAM4LS2BA-MUR

ATSAM4LS2BA-MUR - Cortex-M4 48MHz 128KB MCU | Microchip

The Microchip Technology ATSAM4LS2BA-MUR is a 32-bit ARM Cortex-M4 flash microcontroller running at up to 48 MHz, with 128 KB of embedded flash and 32 KB of SRAM, housed in a 64-pin QFN (9x9 mm) exposed-pad package supplied on tape and reel. A microcontroller unit (MCU) is a single-chip computer that integrates a processor core, memory, and peripherals such as timers, serial interfaces, and analog converters into one integrated circuit. MCUs sit at the heart of embedded systems, below system-on-chip and application processor families in the computing hierarchy, and the SAM4L family belongs to Microchip (formerly Atmel) ATSAM ARM-based flash MCU product line. Key features of the ATSAM4LS2BA-MUR include the ARM Cortex-M4 RISC processor with 48 MHz maximum frequency, 128 KB (128K x 8) of flash program memory, operation from 1.8V, 2.5V, or 3.3V supply rails, and an industrial temperature grade designation. The SAM4L series emphasizes ultra-low-power design with flexible power modes, making it suitable for battery-powered and energy-harvesting designs. Technically, the Cortex-M4 core provides a 3-stage pipeline, hardware divide, and single-cycle multiply for efficient signal processing, while the SAM4L peripheral set typically includes multiple serial communication interfaces and analog peripherals, all clocked from a flexible clock controller supporting multiple sleep and wait modes for active power optimization. Typical applications include industrial sensing nodes, consumer portable devices, building automation, and low-power IoT endpoints where the combination of 48 MHz Cortex-M4 performance and low active current is valuable. A key design consideration is supply selection: the device supports 1.8V/2.5V/3.3V operation, so decoupling and power-tree planning should match the chosen rail, and the exposed pad must be soldered to a grounded PCB land pattern for thermal and electrical performance. This page synthesizes distributor pricing, drop-in alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet.

USD $5,40 Em estoque

ATSAM4LS2CA-AU

ATSAM4LS2CA-AU - ARM Cortex-M4 MCU 48MHz 128KB | Microchip

The Microchip Technology ATSAM4LS2CA-AU is a 32-bit ARM Cortex-M4 flash microcontroller running at up to 48 MHz, with 128 KB (128K x 8) of embedded flash memory, 32 KB of SRAM, and a 100-pin TQFP (14 x 14 mm) package, supplied in industrial temperature grade with hardware crypto acceleration. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest layer of the embedded-system hierarchy: semiconductor -> 32-bit MCU -> ARM Cortex-M microcontroller -> SAM4L series. The ATSAM4LS2CA-AU belongs to the SAM4L family originally developed by Atmel (now Microchip Technology), based on the high-performance 32-bit ARM Cortex-M4 RISC processor. Key features include the 48 MHz Cortex-M4 core with DSP instructions, 128 KB flash for code storage, 32 KB SRAM, a picoPower low-power architecture suited to battery operation, hardware cryptographic acceleration (as noted by Mouser: CRYPTO), and an industrial operating temperature range (-40C to +85C). The Green/RoHS-compliant TQFP package with gull-wing terminals supports standard surface-mount assembly. Per the Atmel/Microchip ATSAM4LS2CA datasheet, the SAM4L family integrates a rich peripheral set including USB, USART, SPI, TWI, and analog peripherals, with low-power modes controlled by the peripheral event system, allowing peripherals to operate while the CPU sleeps. Typical applications include low-power industrial sensing nodes, consumer and portable battery-powered devices, motor and lighting control, and general-purpose embedded control where 128 KB flash and a 100-pin I/O budget fit the design. Design consideration: the device operates at 3.3 V; verify supply sequencing and use proper decoupling on the VDDIO/VDDCORE domains per the datasheet power section. This page synthesizes distributor pricing, pin-compatible same-family alternatives, and practical design notes not found on a single distributor page, with data verified against DigiKey, Mouser, Octopart, and FindIC listings as of 2026-09-20.

USD $3,95 Em estoque

ATSAM4LS2CA-CFU

ATSAM4LS2CA-CFU - 48MHz Cortex-M4 MCU, 128KB Flash | Microchip

The Microchip Technology ATSAM4LS2CA-CFU is a 32-bit ARM Cortex-M4 flash microcontroller running at up to 48 MHz with 128 KB of embedded flash and 32 KB of SRAM, housed in a 100-ball VFBGA (7x7 mm) package for industrial temperature ranges. A microcontroller (MCU) is a single integrated circuit that combines a processor core, program memory, data memory, and peripherals into one chip, forming the lowest tier of the embedded computing hierarchy (MCU -> embedded processor -> system-on-chip -> semiconductor). The SAM4L family belongs to Microchip (formerly Atmel) ARM-based flash MCU lineup, positioned for low-power embedded control applications. Key features include ultra-low active-mode consumption of 90 uA/MHz, sleep mode current as low as 1.5 uA, and wake-up time down to 1.5 us - among the fastest in any Cortex-M4 device. The integrated USB device controller, Peripheral Event System, and SleepWalking peripherals allow data transfer and peripheral operation while the CPU sleeps, dramatically reducing average system power. Technically, the device implements the ARM Cortex-M4 RISC architecture with a 3-stage pipeline, nested vectored interrupt controller, and supply voltage from 1.68 V to 3.6 V. The flash controller supports zero-wait-state execution at reduced frequencies, and the Peripheral Event System routes signals between peripherals without CPU intervention, while SleepWalking lets peripherals wake selectively on qualifying events. Typical applications include battery-powered sensor nodes, portable medical instruments, low-power industrial sensing, and USB-connected human interface devices - anywhere battery life and fast wake-up dominate the design envelope. When designing, exploit SleepWalking and the event system early: architectures that poll in active mode forfeit the SAM4L power advantage, so budget firmware effort for event-driven firmware design. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical low-power design notes not found in the manufacturer datasheet.

USD $3,52 Em estoque

ATSAM4LS4AA-AU

ATSAM4LS4AA-AU - 48MHz Cortex-M4 MCU 256KB Flash | Microchip

The Microchip Technology ATSAM4LS4AA-AU is a 32-bit ARM Cortex-M4 Flash microcontroller running at up to 48 MHz, with 256KB of embedded Flash, in a 48-pin TQFP (7x7 mm) package. It belongs to the SAM4L family, which delivers the lowest active-mode power (90 uA/MHz) and the shortest wake-up time (down to 1.5 us) of any Cortex-M4 device. A microcontroller unit (MCU) integrates a processor core, memory, and peripherals on a single chip, sitting at the center of the embedded systems hierarchy: semiconductor -> integrated circuit -> microcontroller -> 32-bit ARM-based MCU. MCUs replace discrete processor-plus-peripherals combinations in cost- and power-sensitive designs. Key features include the Cortex-M4 core with DSP instructions and FPU-class math support at 48 MHz, 256KB Flash with a dual-bank safe architecture, 16KB SRAM plus an additional 32KB... [DATA_NEEDED: exact SRAM split]. The device provides a USB device port, a Peripheral Event System for inter-peripheral signaling without CPU intervention, and SleepWalking, which lets peripherals wake and act while the core sleeps. The ATSAM4LS4AA-AU uses the picoPower-class SAM4L architecture with multiple sleep modes and hierarchical clock gating, achieving 1.5 uA in sleep mode. Data written into a RAM-based cache plus a Flash accelerator keeps core cycle efficiency high at 48 MHz. Typical applications are battery-powered sensor nodes, wearable and portable medical devices, USB-connected instrument front ends, and low-power industrial monitoring where long battery life and fast wake-up dominate the design. Design consideration: budget the 90 uA/MHz active current against total system duty cycle; frequent wake-ups favor this device because wake-up takes only 1.5 us. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $5,10 Em estoque

ATSAM4LS4AA-AUR

ATSAM4LS4AA-AUR - 48MHz Cortex-M4 MCU, 256KB Flash | Microchip

The Microchip Technology ATSAM4LS4AA-AUR is a 32-bit ARM Cortex-M4 Flash microcontroller running at up to 48 MHz with 256KB of embedded Flash memory, integrated crypto acceleration, and a 48-pin TQFP (7x7 mm) package for industrial-temperature applications. A microcontroller (MCU) is a single-chip computer that integrates a processor core, non-volatile Flash program memory, SRAM data memory, and a rich set of peripherals such as timers, serial interfaces, and analog converters. Within the power-management hierarchy of embedded systems, an MCU is the central control element that orchestrates sensors, communication, and user interfaces. The ATSAM4LS4AA-AUR belongs to Microchip's (formerly Atmel) SAM4L family, a line of ultra-low-power ARM Cortex-M4 Flash microcontrollers positioned above the SAM D20 Cortex-M0+ series and alongside Cortex-M4 competitors from other vendors. The defining feature of the ATSAM4LS4AA-AUR is class-leading power efficiency: 90 uA/MHz in active mode, 1.5 uA in sleep mode, and wake-up times down to 1.5 us - the shortest in a Cortex-M4 device according to the manufacturer. This combination of low active power and instant wake-up makes it possible to duty-cycle demanding DSP workloads from coin cells or energy-harvesting supplies. The device also integrates a USB device controller, a peripheral event system that routes signals between peripherals without CPU intervention, and the innovative SleepWalking feature, which lets peripherals wake the core only when preprogrammed conditions are met. The crypto-capable variant designated by the MRL/CRYPTO suffix adds hardware security acceleration, offloading symmetric and hash operations from software. Operating from a 1.8V to 3.3V supply (per FindIC specification data), the industrial-temperature-grade part suits -40C to +85C environments. Typical applications include battery-powered sensor nodes, portable medical devices, industrial control panels, and USB-connected data loggers - all scenarios where both 32-bit compute (single-cycle MAC, hardware divide for Cortex-M4 DSP instructions) and microamp sleep currents are mandatory. For design, exploit the SleepWalking and peripheral event system to keep the CPU asleep; the wake-up penalty of only 1.5 us means aggressive power gating rarely impacts responsiveness. Size the decoupling network per the SAM4L datasheet recommendations for the 48-TQFP power pins. This page synthesizes distributor pricing, drop-in family alternatives, and practical low-power design guidance not consolidated in the manufacturer datasheet, giving engineers a single citable reference for the ATSAM4LS4AA-AUR.

USD $3,98 Em estoque

ATSAM4LS4AA-MU

ATSAM4LS4AA-MU - 48MHz Cortex-M4 256KB Flash MCU | Microchip

The Microchip Technology ATSAM4LS4AA-MU is a 32-bit ARM Cortex-M4 flash microcontroller running at 48 MHz with 256 KB of embedded Flash memory, housed in a 48-pin QFN (7x7 mm) surface-mount package. It belongs to the SAM4L family, which Microchip (formerly Atmel) positions as the lowest-power Cortex-M4 MCU family, delivering 90 uA/MHz in active mode, 1.5 uA in sleep mode, and wake-up times down to 1.5 us. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest layer of the embedded systems hierarchy: MCU -> embedded processor -> microprocessor-based system. MCUs execute deterministic control and sensing tasks in devices where power budget, cost, and integration matter more than raw throughput. Key features of the ATSAM4LS4AA-MU include the ARM Cortex-M4 core with 32-bit instruction set at up to 48 MHz, 256 KB (256K x 8) of embedded Flash for code storage, an integrated USB device controller, a peripheral event system that routes signals between peripherals without CPU intervention, and the SleepWalking feature that lets peripherals wake the device based on events while RAM and peripheral state are retained. Technically, the SAM4L architecture pairs the Cortex-M4 pipeline with a low-leakage process and a flexible power management scheme with multiple sleep modes. The peripheral event system and SleepWalking offload the CPU, so the core can stay in deep sleep while peripherals such as ADC, timers, and communication blocks continue operating, dramatically reducing average system current in duty-cycled designs. Typical applications include battery-powered portable instruments, sensor nodes and IoT endpoints, and consumer or industrial devices requiring USB connectivity with long battery life. The 48 MHz Cortex-M4 with DSP instructions also handles modest digital filtering and control loops efficiently. For design, minimize active-mode time by exploiting sleep modes and the event system, and verify the exact pinout and peripheral multiplexing from the Microchip SAM4L datasheet before layout, since QFN packages require careful thermal pad soldering. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $3,95 Em estoque

ATSAM4LS4AA-MUR

ATSAM4LS4AA-MUR - Cortex-M4 48MHz 256KB Flash MCU | Microchip

The Microchip Technology ATSAM4LS4AA-MUR is a 32-bit ARM Cortex-M4 flash microcontroller running at 48 MHz with 256 KB of embedded Flash memory, housed in a 48-pin QFN (7x7 mm) package with exposed pad and supplied in tape and reel packaging for industrial temperature ranges. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest layer of the embedded systems hierarchy: MCU -> embedded processor -> SoC -> computing system. The SAM4L series belongs to Microchip's (formerly Atmel's) ARM-based Flash MCU portfolio, placing a Cortex-M4 core with DSP instructions inside a low-power peripheral set. Key features include the lowest active-mode power in its class at 90 uA/MHz, sleep mode current down to 1.5 uA, and a wake-up time as short as 1.5 us, the fastest in any Cortex-M4 device according to Microchip. The integrated USB device controller, peripheral event system, and SleepWalking technology allow peripherals to operate and wake the core autonomously, minimizing CPU active time in battery-powered designs. Architecturally, the SAM4L combines the 32-bit ARM Cortex-M4 RISC processor with a multi-layer bus matrix, flexible event-driven peripherals, and 3.3V operation. The peripheral event system routes signals between peripherals without core intervention, while SleepWalking lets peripherals pre-process data in low-power sleep states, dramatically reducing average system power in duty-cycled applications. Typical applications include battery-powered sensor nodes, portable medical devices, industrial data loggers, and USB-connected human interface devices, where the combination of 256 KB Flash, USB, and microamp sleep currents fits both connectivity and energy budgets. Design consideration: budget the Flash wait-state configuration carefully at 48 MHz and use the SleepWalking event system to keep the Cortex-M4 core parked whenever possible. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $3,55 Em estoque

ATSAM4LS4BA-AU

ATSAM4LS4BA-AU - 48MHz Cortex-M4 256KB MCU | Microchip

The Microchip Technology ATSAM4LS4BA-AU (originally Atmel) is a 32-bit ARM Cortex-M4 microcontroller running at 48 MHz with 256 KB flash, 32 KB SRAM, and hardware cryptographic acceleration, housed in a 64-pin TQFP (10x10 mm) package. A microcontroller (MCU) is a single integrated circuit that combines a processor core, nonvolatile program memory, RAM, and a rich set of peripherals such as timers, serial interfaces, and analog converters. Microcontrollers sit at the lowest level of the embedded-system hierarchy - below applications processors and system-on-chip devices - and are the workhorses of industrial control, consumer appliances, and IoT nodes. The SAM4L family belongs to the ARM Cortex-M class of energy-efficient 32-bit MCUs, and specifically targets low-power designs with its picoPower technology and multiple sleep modes. Key features of the ATSAM4LS4BA-AU include the single-core ARM Cortex-M4 processor with DSP and floating-point instructions, 256 KB (256K x 8) of single-cycle flash program memory, 32 KB of SRAM, and an AES/DES hardware cryptographic engine highlighted in the Mouser listing (CRYPTO, MRL A, industrial temperature). The device operates from a nominal 3.3 V supply (1.62 V to 3.6 V range typical for the SAM4L family) and is qualified for industrial temperature environments. Peripherals such as USB, USART, SPI, I2C/TWI, 12-bit ADC, and capacitive-touch support (Peripheral Touch Controller) make it a complete system-on-chip for sensing and connectivity tasks. Architecturally, the SAM4L integrates a flash accelerator to keep the Cortex-M4 pipeline fed at 48 MHz, a multi-layer bus matrix, low-leakage process technology, and flexible sleep/shutdown modes with wake-up controllers that reduce standby consumption to microamp levels - a key differentiator versus the SAM4S family for battery-powered designs. Typical applications include low-power industrial sensors and data loggers, consumer appliances with capacitive-touch user interfaces, battery-powered metering and IoT nodes, and secure products that benefit from the on-chip AES/DES crypto accelerator. When designing with this device, budget the flash endurance and use the multiple power domains and sleep modes deliberately: the biggest performance win in SAM4L designs usually comes from firmware power management, not silicon selection. Validate the 64-TQFP (10x10) footprint and decoupling network early. This page synthesizes distributor pricing, drop-in SAM4L family alternatives, and practical design notes not found in the manufacturer datasheet, based on verified web data as of 2026-09-20.

USD $6,02 Em estoque

ATSAM4LS4BA-AUR

ATSAM4LS4BA-AUR - 32-bit ARM Cortex-M4 48MHz MCU 256KB | Microchip

The Microchip Technology (Atmel) ATSAM4LS4BA-AUR is a 32-bit ARM Cortex-M4 flash microcontroller with a 48 MHz core, 256KB (256K x 8) of embedded flash memory, and industrial temperature operation, housed in a 64-pin TQFP (10x10 mm) surface-mount package on tape and reel. A microcontroller (MCU) is a complete computing system integrated onto a single chip, combining a processor core, program memory, data memory, and a rich set of peripherals. The ARM Cortex-M4 at the heart of the SAM4L family sits near the top of the embedded processor hierarchy, which runs from simple 8-bit cores through Cortex-M0/M0+ up to the DSP-capable Cortex-M4, making the SAM4L suitable for mid-to-high-performance embedded control, sensing, and connectivity tasks. Key features of the ATSAM4LS4BA-AUR include the Cortex-M4 RISC processor running at 48 MHz with single-cycle DSP instructions and a hardware FPU, 256KB of flash for code storage, operation from 1.8V or 3.3V supplies, and an industrial temperature grade of -40C to +85C. The device also integrates a hardware cryptographic engine, as noted on distributor listings (TQFP, Green, IND TEMP, CRYPTO, MRL A), which accelerates AES and other security primitives for secure IoT and connected products. Architecturally, the SAM4L series is optimized for ultra-low-power applications: it uses a low-leakage process and multiple power modes, including sleep, wait, and backup modes, allowing battery-powered designs to spend most of their life in standby while retaining fast wake-up to active execution. The Cortex-M4 core delivers approximately 1.25 DMIPS/MHz, so the 48 MHz clock yields roughly 60 DMIPS, sufficient for sensor fusion, digital filtering, and lightweight protocol stacks. Typical applications include battery-powered industrial sensors, building automation nodes, consumer appliances, portable medical accessories, and secure connected devices where the cryptographic engine and low-power modes directly extend product battery life. For design, budget flash usage carefully: 256KB is generous for control code but tight for large BLE or TLS stacks, in which case a higher-memory SAM4L variant in the same package should be considered. Follow Microchip layout guidance for decoupling and VDDIO domain separation to maximize noise immunity. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet, providing a single self-contained reference for selection engineers.

USD $3,42 Em estoque

ATSAM4LS4BA-MU

ATSAM4LS4BA-MU - 48MHz Cortex-M4 256KB MCU | Microchip

The Microchip Technology ATSAM4LS4BA-MU is a 32-bit ARM Cortex-M4 microcontroller running at 48 MHz with 256 KB flash memory and 32 KB SRAM, housed in a 64-pin QFN (9x9 mm) package with exposed pad. A microcontroller (MCU) is a complete computing system on a single chip, integrating a processor core, program memory, data memory, and peripheral functions such as timers, communication interfaces, and analog converters. Within the power-management hierarchy, an MCU like the SAM4L often acts as the master controller of a system, coordinating sensors, power management ICs, and communication devices. The ARM Cortex-M4 core adds DSP instructions and hardware floating-point capability to the widely used 32-bit MCU ecosystem. Key features of the ATSAM4LS4BA-MU include the SAM4L series focus on ultra-low power consumption, a 48 MHz maximum core clock, 256 KB of on-chip flash, 32 KB of SRAM, and an industrial operating temperature range, as confirmed by DigiKey and Mouser distributor listings. The 64-QFN no-lead package supports compact surface-mount designs with good thermal performance via the exposed pad. Technically, the device combines the ARMv7E-M architecture with Microchip (formerly Atmel) peripheral IP from the SAM4L family, offering a 32-bit RISC datapath, nested vectored interrupt controller, and multiple low-power sleep modes. The flash-based program memory allows in-system reprogramming, and the 3.3 V supply class simplifies integration with modern sensors and transceivers. Typical applications include industrial control panels, battery-powered metering and IoT sensor nodes, and consumer appliances that need a balance of DSP-class performance and low standby power. The Cortex-M4 core handles digital filtering and control loops efficiently, while the flash and SRAM capacity suits protocol stacks and small RTOS kernels. When designing with this MCU, budget supply decoupling and PCB thermal relief on the exposed pad early, and verify that 256 KB flash meets final firmware size including a bootloader and OTA margin. This page synthesizes distributor pricing, drop-in alternatives within the SAM4L family, and practical design notes not found in the manufacturer datasheet alone.

USD $1,85 Em estoque

ATSAM4LS4BA-MUR

ATSAM4LS4BA-MUR - 48MHz Cortex-M4 256KB MCU | Microchip

The Microchip Technology ATSAM4LS4BA-MUR is a 32-bit ARM Cortex-M4 flash microcontroller in the SAM4L series, running at up to 48 MHz with 256 KB (256K x 8) of embedded Flash, 32 KB of SRAM, and a 1.68V to 3.6V supply range, housed in a 64-pin QFN (9x9 mm) package with exposed pad. A 32-bit microcontroller (MCU) is an integrated circuit that combines a processor core, memory, and peripherals on a single chip, sitting within the broader hierarchy of embedded processors: microcontroller -> ARM Cortex-M core family -> system-on-chip for embedded control. The SAM4L family is Atmel (now Microchip) Flash MCUs based on the high-performance ARM Cortex-M4 RISC processor, which includes a hardware floating-point unit and DSP instructions. Key features include the 48 MHz Cortex-M4 core with FPU, 256 KB Flash and 32 KB SRAM, and low-power operation suited to battery-powered designs. The industrial temperature grade and Tape & Reel (T/R) packaging support automated high-volume assembly. The SAM4L architecture integrates a multi-layer bus matrix, flexible peripheral event system, and power-management controller with multiple sleep modes, allowing peripherals to operate while the CPU sleeps to minimize energy per task in low-power applications. Typical applications include battery-powered portable instruments, industrial sensing and control nodes, and consumer devices requiring a balance of processing performance (hardware floating point at 48 MHz) and low standby power. Design consideration: operate the device within the 1.68V to 3.6V supply window (nominal 3.3V) and confirm GPIO assignments against the manufacturer datasheet before layout, as QFN packages with exposed pads require careful thermal and ground pad soldering. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.

USD $4,25 Em estoque

ATSAM4LS4BA-UUR

ATSAM4LS4BA-UUR - 48MHz Cortex-M4 MCU 256KB Flash | Microchip

The Microchip ATSAM4LS4BA-UUR is a 32-bit ARM Cortex-M4 flash microcontroller from the SAM4L series, running at up to 48 MHz with 256KB (256K x 8) flash memory, 32KB SRAM, and a supply range of 1.62V to 3.6V, housed in a 64-ball WLCSP package measuring 4.31 x 4.43 mm and supplied in tape and reel. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest layer of the embedded systems hierarchy: MCU -> embedded processor -> system-on-chip -> semiconductor device. The SAM4L family belongs to Atmel (now Microchip Technology) ARM-based flash microcontrollers, positioned for low-power embedded control. Key features include the high-performance 32-bit ARM Cortex-M4 RISC processor core, 10-bit and 12-bit ADC options for analog sensing, and operation across multiple nominal supply rails of 1.8V, 2V, 2.3V, and 3.3V. The extremely compact 64-WLCSP (4.31 x 4.43 mm) ball grid array package makes the device attractive for space-constrained portable electronics where board area is the dominant constraint. Technically, the SAM4L series is a member of a family of flash microcontrollers based on the high-performance 32-bit ARM Cortex-M4 RISC processor. The Cortex-M4 core brings hardware DSP instructions and single-cycle MAC capability, allowing filtering and control-loop math to execute efficiently at the modest 48 MHz clock while preserving the SAM4L series low-power design philosophy. Typical applications include battery-powered portable instruments, wearable and sensor-node designs, industrial sensing front-ends using the 10/12-bit ADCs, and compact embedded controllers where a 32-bit ARM ecosystem with 256KB of on-chip flash is required in a minimal footprint. A key design consideration is the WLCSP package itself: wafer-level chip-scale balls demand tight PCB pad accuracy and reflow control, and the underside ball array requires careful via-in-pad or escape-routing strategy for signal access. This page synthesizes distributor pricing, drop-in family alternatives, comparison data, and practical WLCSP layout guidance not consolidated in the manufacturer datasheet.

USD $5,75 Em estoque

ATSAM4LS4CA-AUR

ATSAM4LS4CA-AUR - 32-bit ARM Cortex-M4 48MHz MCU | Microchip

The Microchip Technology ATSAM4LS4CA-AUR is a 32-bit ARM Cortex-M4 flash microcontroller running at up to 48 MHz with 256 KB of embedded flash memory and 32 KB of SRAM, housed in a 100-pin TQFP (14 x 14 mm) surface-mount package. A microcontroller (MCU) is a single integrated circuit that combines a processor core, program memory, data memory, and a rich set of peripherals onto one chip, forming the complete embedded control hierarchy: processor core -> MCU -> embedded system. The ATSAM4LS4CA-AUR belongs to the Atmel/Microchip SAM4L family, built on the ARM Cortex-M4 RISC architecture with Thumb-2 instruction set, positioning it in the mainstream 32-bit embedded controller class between simple Cortex-M0 parts and high-performance Cortex-M7 devices. Key features include the high-efficiency Cortex-M4 core with DSP-friendly single-cycle multiply instructions, 256 KB (256K x 8) of flash program memory, 32K x 8 SRAM, and an ultra-low-power design that makes the SAM4L series a benchmark for energy-sensitive applications. On-chip analog includes both 10-bit and 12-bit ADC capability per distributor data, and security is supported by a hardware AES crypto module, as noted in Mouser listing attributes (CRYPTO). Technically, the SAM4L implements a multilayer bus matrix, sleepwalking peripheral operation, and multiple low-power sleep modes so that RAM retention and peripheral wake-up can be managed independently of the CPU clock. The industrial temperature grade (-40C to +85C) and 1.68 V to 3.6 V single-supply operation allow direct battery and 3.3 V rail designs. Typical applications include portable battery-powered instruments, industrial sensors and actuators, consumer appliances, and low-power IoT nodes where the 48 MHz Cortex-M4 core processes control loops and sensor data with crypto-secured communication links. When designing with this device, budget the flash endurance and use the on-chip brown-out and clock-fail detection features; supply decoupling on all VDD/VDDIO pairs and a clean 3.3 V rail preserve ADC accuracy. This page adds distributor pricing tiers, drop-in family alternatives, design notes, and comparison data synthesized from DigiKey, Mouser, Octopart, and LCSC listings - information not consolidated in the manufacturer datasheet.

USD $4,85 Em estoque

ATSAM4LS4CA-CFUR

ATSAM4LS4CA-CFUR - 48MHz Cortex-M4 MCU 256KB Flash | Microchip

The Microchip Technology ATSAM4LS4CA-CFUR (Atmel SAM4L series) is a 32-bit ARM Cortex-M4 flash microcontroller running at up to 48 MHz with 256KB embedded Flash and 3.3V operation, housed in a 100-ball VFBGA package measuring 7x7 mm and supplied in tape-and-reel packing. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, sitting at the device level of the embedded-systems hierarchy (MCU -> embedded processor -> semiconductor IC). The SAM4L family is based on the high-performance 32-bit ARM Cortex-M4 RISC processor, providing DSP-oriented instructions and efficient interrupt handling for low-power embedded designs. Key features of the ATSAM4LS4CA-CFUR include the ARM Cortex-M4 core at 48 MHz for computationally capable but energy-conscious applications, 256KB (256K x 8) of on-chip Flash for code storage, and a 100-VFBGA (7x7 mm) ball grid array footprint that saves board area in space-constrained products. The part is specified for industrial temperature range operation and is available as a Green (RoHS-oriented) package with MSL rating A per distributor listings. From a technical perspective, the SAM4L series emphasizes low active and sleep-mode power consumption while retaining the Cortex-M4 integer DSP capability, making it distinct from Cortex-M3-based parts at similar clock speeds. The 100-ball VFBGA requires precise PCB land-pattern design and reflow assembly, but yields the smallest possible footprint for a 100-pin SAM4L device. Typical applications include portable and battery-powered instruments, industrial sensing nodes, consumer appliances, and low-power IoT end points where a 48 MHz Cortex-M4 with 256KB Flash provides adequate performance headroom. When designing with this device, plan power-delivery decoupling for the BGA ballout and verify Flash capacity against application growth, since the 256KB density sits mid-range in the SAM4L family. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet. Pricing references LCSC reference pricing of $2.6888 as of 2026-09-20.

USD $1,98 Em estoque

ATSAM4LS8AA-MU

ATSAM4LS8AA-MU - ARM Cortex-M4 MCU 48MHz 512KB Flash | Microchip

The Microchip Technology ATSAM4LS8AA-MU is a 32-bit ARM Cortex-M4 flash microcontroller running at up to 48 MHz with 512 KB of embedded Flash and 64 KB of SRAM, housed in a 48-pin QFN (7x7 mm) surface-mount package. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest layer of the embedded system hierarchy: MCU -> microcontroller -> embedded processor -> system-on-chip. The SAM4L family sits within Microchip's ATSAM ARM-based flash MCU portfolio and targets low-power, battery-operated and energy-harvesting designs. Key features include industry-leading active-mode consumption of 90 uA/MHz, sleep mode current of just 1.5 uA, and wake-up times down to 1.5 us, which together rank among the lowest power figures of any Cortex-M4 device. The integrated USB device peripheral, peripheral event system, and the proprietary SleepWalking technology allow peripherals to operate autonomously while the CPU core and clock domains remain powered down, dramatically extending battery life. Architecturally, the SAM4L combines the ARM Cortex-M4 core with Microchip's picoPower techniques, a multi-layer bus matrix, and a flexible peripheral set. The peripheral event system routes inter-peripheral signals without CPU intervention, reducing latency and active power. Embedded Flash supports the code base while SRAM retains data through deep-sleep states, supporting rapid context restoration on wake-up. Typical applications include battery-powered sensor nodes and IoT end devices, portable medical and fitness monitors, and low-power industrial control and metering products where every microamp of average current directly extends field life. For design, take advantage of the SleepWalking framework early in the software architecture: assign wake-up sources and event routes before finalizing the schematic, and decouple the VDDCORE and VDDIO domains with low-ESR ceramic capacitors placed close to the QFN pads. This page synthesizes distributor availability data, same-family drop-in alternatives, and practical low-power design guidance not found in the manufacturer's product brief.

Cotação Em estoque

ATSAM4LS8BA-AU

ATSAM4LS8BA-AU - Cortex-M4 48MHz 512KB MCU | Microchip

The Microchip Technology ATSAM4LS8BA-AU is a 32-bit ARM Cortex-M4 flash microcontroller delivering 48 MHz performance, 512KB of embedded flash, and 64KB of SRAM in a 64-pin TQFP (10x10 mm) surface-mount package. It belongs to the SAM4L family, which Microchip (formerly Atmel) positions as the lowest-power Cortex-M4 MCU line, with active-mode consumption of 90 uA/MHz, sleep-mode current of 1.5 uA, and wake-up times down to 1.5 us. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip. Within the semiconductor hierarchy, the ATSAM4LS8BA-AU sits at: ARM Cortex-M4 MCU -> 32-bit microcontroller -> SAM4L family -> embedded processing -> semiconductor device. MCUs are the core building blocks of embedded systems, controlling sensors, actuators, and communication interfaces in everything from consumer gadgets to industrial equipment. Key differentiating features include the Cortex-M4 core with DSP instructions, an integrated USB 2.0 device controller, a Peripheral Event System that routes signals between peripherals without CPU intervention, and the proprietary SleepWalking technology that lets peripherals operate autonomously while the core sleeps. These attributes make it exceptionally well suited to battery-powered and energy-harvesting designs that still require substantial processing throughput. The SAM4L architecture also integrates a flash accelerator for zero-wait-state execution at full speed, multiple low-power sleep modes, an AES/DES cryptographic option on sibling parts, and analog peripherals including a 12-bit ADC and DAC. The wide 1.62V to 3.6V operating supply range supports direct operation from single-cell lithium and 3.3V industrial rails. Typical applications include portable medical instruments, battery-powered metering, IoT sensor nodes, consumer appliance control, and industrial monitoring where long battery life is a design requirement. The 48 MHz Cortex-M4 with hardware divide and single-cycle MAC handles digital filtering and control loops efficiently. A key design consideration is power budgeting: exploit the SleepWalking peripheral system and fast wake-up to remain in the deepest possible sleep mode between events, since active current dominates the energy profile in duty-cycled systems. This page synthesizes distributor pricing from multiple sources, drop-in family alternatives, and practical design guidance not found in the manufacturer datasheet alone. Pricing references are as of 2026-09-20.

USD $4,34 Em estoque

ATSAM4LS8BA-AUR

ATSAM4LS8BA-AUR - 512KB Cortex-M4 48MHz MCU | Microchip

The Microchip Technology ATSAM4LS8BA-AUR is a 32-bit ARM Cortex-M4 flash microcontroller running at 48 MHz with 512 KB of embedded flash memory, housed in a 64-pin TQFP (10x10 mm) surface-mount package with exposed pad and supplied in tape-and-reel format. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest tier of the embedded processing hierarchy (MCU -> embedded processor -> microprocessor -> SoC). The SAM4L family belongs to Microchip's (formerly Atmel) ARM-based flash MCU portfolio, built on the 32-bit ARM Cortex-M4 RISC architecture that adds DSP instructions and single-cycle MAC for math-intensive embedded workloads. The defining strength of the ATSAM4LS8BA-AUR is ultra-low power consumption: Microchip specifies the lowest active-mode current in its class at 90 uA/MHz, sleep-mode current of 1.5 uA, and wake-up time down to 1.5 us - the shortest wake-up among Cortex-M4 devices at the time of release. A 512 KB single-cycle flash array, integrated USB device controller, Peripheral Event System (direct peripheral-to-peripheral signaling without CPU intervention), and Sleepwalking peripherals (peripherals that operate while the CPU sleeps) let battery-powered systems stay in sleep states far longer than conventional MCUs. Architecturally, the Cortex-M4 core is complemented by the SAM4L bus matrix, multi-source interrupt controller, and a rich analog/mixed-signal peripheral set operating from a 3.3 V supply. The Peripheral Event System and Sleepwalking capability offload periodic tasks - ADC sampling, comparator monitoring, timed wakeups - from the core entirely. Typical applications include battery-powered sensor nodes and IoT devices, portable medical instruments, low-power industrial sensing, and consumer devices requiring USB connectivity with long battery life. Design tip: exploit the Sleepwalking peripherals to keep the Cortex-M4 in a low-power sleep mode as much as possible; wake-up latency of 1.5 us means even event-driven designs do not need to trade responsiveness for power savings. This page synthesizes verified distributor listings, drop-in alternatives, and low-power design guidance not consolidated in the manufacturer datasheet.

USD $4,72 Em estoque

ATSAM4LS8BA-MU

ATSAM4LS8BA-MU - 48MHz Cortex-M4 512KB MCU | Microchip

The Microchip Technology ATSAM4LS8BA-MU is a 32-bit ARM Cortex-M4 flash microcontroller running at up to 48 MHz with 512KB of embedded Flash memory, ultra-low 90 uA/MHz active-mode current, and a 64-pin QFN (9x9 mm) exposed-pad package. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory (Flash for code and SRAM for data), and a rich set of peripherals (timers, serial interfaces, ADCs) on one die. Within the power-management hierarchy, MCUs like the SAM4L sit at the lowest power tier of 32-bit embedded processing, below application processors, and are optimized for battery-powered and energy-harvesting systems where every microamp matters. The ATSAM4LS8BA-MU differentiates itself with the lowest power in its class: 90 uA/MHz in active mode, 1.5 uA in sleep mode, and a wake-up time as short as 1.5 us, which Microchip reports as the fastest in any Cortex-M4 device. It integrates a USB device controller, a peripheral event system that lets peripherals communicate without CPU intervention, and the Sleepwalking feature that allows peripherals to operate autonomously while the core sleeps. Architecturally, the device is based on the high-performance 32-bit ARM Cortex-M4 RISC processor with a 3-stage pipeline and single-cycle MAC/DSP instructions. The SAM4L family adds a picoPower technology portfolio: multiple sleep modes, a reduced core voltage of 3.3V operation, and peripheral gating. The embedded Flash with 512KB (512K x 8) density supports field firmware updates, and the exposed-pad HVQCCN QFN package provides excellent thermal and grounding performance for compact designs. Typical applications include battery-powered sensor nodes, smart meters, portable medical monitors, wearable devices, industrial IoT endpoints, and low-power USB accessories where fast wake-up and long battery life dominate the design requirements. Designers should budget the lowest-power sleep mode against wake-up latency: the 1.5 us wake-up enables aggressive duty cycling, but peripheral Sleepwalking configurations require careful clock and event-system planning to actually realize the datasheet-level current figures. This page synthesizes distributor pricing, drop-in SAM4L family alternatives, pinout guidance, and practical design notes not found in a single manufacturer datasheet, saving engineers cross-referencing time.

USD $1,02 Em estoque

ATSAM4LS8BA-UUR

ATSAM4LS8BA-UUR - Cortex-M4 48MHz 512KB Flash WLCSP-64 | Microchip

The Microchip Technology ATSAM4LS8BA-UUR is a 32-bit ARM Cortex-M4 flash microcontroller running at 48 MHz with 512KB embedded Flash, housed in a 64-ball WLCSP (wafer-level chip-scale) package measuring approximately 4.31 x 4.43 mm. A microcontroller (MCU) integrates a processor core, memory, and peripherals on a single chip, sitting at the top of the hierarchy: MCU -> embedded processor -> semiconductor device. The SAM4L family belongs to Microchip's (formerly Atmel's) ARM-based flash MCU portfolio, targeting ultra-low-power embedded systems that still require 32-bit DSP-class performance from the Cortex-M4 core. Key features include the lowest active-mode consumption in its class (90 uA/MHz per the manufacturer product page), 1.5 uA sleep-mode current, and wake-up times down to 1.5 us - the shortest among Cortex-M4 devices at introduction. The chip integrates a USB device controller, a peripheral event system that lets peripherals communicate without CPU intervention, and the SleepWalking feature that allows peripherals to operate while the CPU core is asleep, dramatically reducing average power in duty-cycled systems. Technically, the SAM4L uses the ARM Cortex-M4 RISC architecture with single-cycle multiply and hardware divide, a multi-layer bus matrix, and flexible supply operation around 1.8V to 3.3V (FindIC lists 1.8V/2V/2.3V/3.3V nominal rails). The 512KB Flash supports in-system programming, and industrial temperature grade operation (-40C to +85C) suits harsh environments. Typical applications include battery-powered wearable and portable devices, sensor nodes and IoT endpoints, low-power data loggers, and space-constrained medical monitoring products where the 4.31 x 4.43 mm WLCSP-64 footprint and low sleep current are decisive. Design consideration: WLCSP packages require precise PCB land-pattern design and solder-mask-defined pads; verify the manufacturer's ball-map document before layout and budget rework difficulty accordingly. This page adds value beyond the datasheet by consolidating verified distributor pricing, drop-in alternative analysis within the SAM4L family, design notes, and AEO-optimized answers to common engineering questions.

USD $2,03 Em estoque

Produtos (18688)