MCZ33972EWR2 - 22-Ch Switch Monitor SPI Interface | NXP
N.º da peça: MCZ33972EWR2 ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $5.42 | $5,42 |
| 10 | $4.87 | $48,70 |
| 100 | $4.35 | $435,00 |
| 500 | $3.91 | $1.955,00 |
| 1.000 | $3.52 | $3.520,00 |
MCZ33972EWR2 Visão geral
A Multiple Switch Detection Interface (MSDI) is a type of mixed-signal automotive interface IC that combines analog input multiplexing, programmable current sources, threshold comparators, and a digital serial interface into a single device. In the system hierarchy it belongs to Interface ICs > Specialized Interface ICs, bridging low-level mechanical switches to digital logic. Its primary purpose is to replace dozens of discrete pull-ups, comparators, and wiring with one rugged, AEC-qualified IC, which is critical for body controllers, HVAC panels, and steering-wheel switch clusters.
Key features of the MCZ33972EWR2 include detection of 22 switch inputs, a 16-bit SPI output word, user-selectable switch-to-ground or switch-to-battery configuration, programmable wetting current (2 mA / 6 mA / 12 mA / 16 mA typical), and an integrated 22:1 analog MUX output for ratiometric measurement. The wake-up feature pulses a current briefly through each switch on a programmed interval, then returns to a low-Iq Sleep mode, drastically reducing quiescent current in parked-vehicle applications. Normal mode allows continuous monitoring at full speed and full programming access.
The device uses an internal 5 V regulator derived from V_PWR to power analog and digital blocks, and provides an interrupt output (INT) to wake the host MCU on any switch state change. The on-chip 22-to-1 analog multiplexer allows a single ADC on the MCU to sequentially read each switch node for ratiometric diagnostics (open circuit, short to battery, short to ground). The architecture is designed to tolerate 40 V load-dump transients common in 12 V automotive networks, with reverse-battery protection on V_PWR.
Typical applications include automotive body controllers detecting door, hood, trunk and seatbelt switches, HVAC control panels reading push-buttons and rotary encoders, steering-wheel switch clusters, instrument-cluster switch input, and industrial control panels with multiple contact closures. Its suppressed wake-up and low quiescent current make it well-suited to any battery-powered application where the system must wake on a switch event without continuously drawing power.
Designers should note that the 32-SOIC package requires thermal relief and adequate copper for the exposed-pad power-dissipation path, and that the analog MUX output should be buffered if more than a few hundred pF of capacitance is present on the trace. PCB layout must keep the analog MUX trace away from switching power traces to preserve diagnostic accuracy.
This page synthesizes NXP datasheet specifications, distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer product page alone.
Alternativas drop-in para MCZ33972EWR2 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com MCZ33972EWR2 (mesmo formato e footprint) — diferindo em Analog Multiplexer, Function, Host Interface, Interrupt Output, Packaging.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
MCZ33972AEW
✅ Drop-In✓ Em estoque
$2.34 / unidade
Ver ficha técnica →MCZ33972EWR2G
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MC33972AEW
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MCZ33972EWR2 Classificações máximas e características elétricas
| Função | Multiple Switch Detection Interface (MSDI) with suppressed wake-up |
| Number of Switch Inputs | 22 |
| Host Interface | 16-bit SPI (Serial Peripheral Interface) |
| Supply Voltage (V_PWR) | 8 V to 26 V |
| Operating Voltage Range | 6 V to 26 V (extended, including load-dump transient up to 40 V) |
| Wetting Current (programmable) | 2 mA / 6 mA / 12 mA / 16 mA typical |
| Analog Multiplexer | 22-to-1 analog MUX output |
| Modes of Operation | Normal mode and Sleep (low-Iq) mode |
| Interrupt Output | Yes (active-low INT pin) |
| Switch Configuration | Switch-to-ground or switch-to-battery, software selectable |
| Reverse Battery Protection | Yes, on V_PWR |
| Load-Dump Tolerance | 40 V transient on V_PWR |
| Encapsulamento / Caixa | 32-SOIC (0.295 in / 7.50 mm width, wide-body) |
| Tipo de montagem | Surface Mount |
| Packaging | Tape & Reel (TR) |
| Lead Free Status | Lead Free / RoHS compliant |
| Temperatura de operação | -40 C to +125 C (automotive grade) |
| Automotive Qualification | AEC-Q100 qualified |
Configuração de pinos do MCZ33972EWR2
| Pino 1 | SP0 — Switch input 0 (analog/digital, programmable wetting current) |
| Pino 2 | SP1 — Switch input 1 |
| Pino 3 | SP2 — Switch input 2 |
| Pino 4 | SP3 — Switch input 3 |
| Pino 5 | SP4 — Switch input 4 |
| Pino 6 | SP5 — Switch input 5 |
| Pino 7 | SP6 — Switch input 6 |
| Pino 8 | SP7 — Switch input 7 |
| Pino 9 | SP8 — Switch input 8 |
| Pino 10 | SP9 — Switch input 9 |
| Pino 11 | SP10 — Switch input 10 |
| Pino 12 | SP11 — Switch input 11 |
| Pino 13 | SP12 — Switch input 12 |
| Pino 14 | SP13 — Switch input 13 |
| Pino 15 | SP14 — Switch input 14 |
| Pino 16 | SP15 — Switch input 15 |
| Pino 17 | SP16 — Switch input 16 |
| Pino 18 | SP17 — Switch input 17 |
| Pino 19 | SP18 — Switch input 18 |
| Pino 20 | SP19 — Switch input 19 |
| Pino 21 | SP20 — Switch input 20 |
| Pino 22 | SP21 — Switch input 21 |
| Pino 23 | MUX_OUT — 22-to-1 analog multiplexer output |
| Pino 24 | INT — Interrupt output (active-low, signals switch change to MCU) |
| Pino 25 | MISO — SPI Master-In Slave-Out |
| Pino 26 | MOSI — SPI Master-Out Slave-In |
| Pino 27 | SCLK — SPI serial clock |
| Pino 28 | CS — SPI chip select (active-low) |
| Pino 29 | VDD — 5 V internal regulator output (decouple with 100 nF + 10 uF) |
| Pino 30 | V_PWR — Battery supply input (8 V to 26 V, 40 V load-dump tolerant) |
| Pino 31 | GND — Ground |
| Pino 32 | GND — Ground (second bond pad for thermal dissipation) |
Aplicações típicas
MCZ33972EWR2 é adequado para 6 aplicaçãos: Automotive Body Controller Switch Inputs, HVAC Control Panel Switch Matrix, Steering-Wheel Switch Cluster Interface, Instrument Cluster Switch Inputs, Industrial Control Panel Discrete I/O, Battery-Powered Switch-Wake Systems.
Automotive Body Controller Switch Inputs
The MCZ33972EWR2 is ideal for automotive body controllers that aggregate door, hood, trunk, and seatbelt switch signals, because a single IC monitors up to 22 switch contacts and reports each one's open/closed state over a 16-bit SPI frame to the host MCU. The 8 V to 26 V V_PWR range and 40 V load-dump tolerance let it connect directly to the 12 V automotive battery bus without additional protection, while the suppressed-wake-up behavior keeps quiescent current below the 100 uA range in parked-vehicle mode. Compared to a discrete resistor-and-comparator design, the 33972 saves PCB area, reduces wiring complexity, and adds AEC-Q100 reliability that discrete implementations cannot match.
Recomendado
HVAC Control Panel Switch Matrix
HVAC control panels typically contain 15 to 22 push-buttons and rotary-encoder contacts that must be scanned continuously while consuming minimal board space; the MCZ33972EWR2 handles this in a single 32-SOIC IC. Its programmable wetting current (2 mA, 6 mA, 12 mA or 16 mA) lets designers tune switch-bounce suppression and contact-cleaning current for each panel revision without hardware changes. The integrated 22-to-1 analog multiplexer allows a single external ADC on the HVAC MCU to perform ratiometric diagnostics on each switch for open-circuit and short-to-ground/battery detection - a feature that would otherwise require an additional analog mux chip in a discrete implementation.
Recomendado
Steering-Wheel Switch Cluster Interface
Steering-wheel switch clusters for audio, cruise-control, and phone functions typically combine 8 to 14 momentary switches routed through a clock-spring harness into the body controller. The MCZ33972EWR2EWR2 reduces the number of wires through that harness from one-per-switch to one SPI bus (4 wires: SCLK, MOSI, MISO, CS) plus power and ground. This is critical because clock-springs have a finite cycle life; reducing harness wires by a factor of three to four improves long-term reliability. The device's switch-to-battery or switch-to-ground programmability means the same IC handles different contact topologies used by different OEMs.
Recomendado
Instrument Cluster Switch Inputs
Instrument clusters integrate trip-reset, dimmer, and mode-select switches that must be debounced and reported to the cluster MCU with minimal latency. The MCZ33972EWR2 reads all 22 contacts in a single SPI frame, and its active-low INT pin fires immediately on any state change, giving the cluster near-instant response to driver inputs. The on-chip diagnostics also detect failed switches (open or shorted) which is increasingly required for OEM warranty analysis. The 32-SOIC wide-body footprint fits easily behind the cluster PCB alongside the stepper-motor gauge drivers, where the same SPI bus can be shared between the switch IC and the gauge driver.
Recomendado
Industrial Control Panel Discrete I/O
Industrial control panels frequently require 16 to 22 dry-contact or 24 V wet-contact inputs that must be electrically isolated from the controller logic. The MCZ33972EWR2's 8 V to 26 V supply range matches the 24 V industrial bus directly, and its wetting-current programmability lets the same IC handle both dry (mechanical) and wet (transistor-driven) contacts. According to the NXP datasheet, the analog MUX output allows the host PLC to perform ratiometric voltage reads on each input for diagnostic logging. Compared to 22 individual optocouplers, the 33972 reduces BOM cost, board area, and assembly time substantially.
Recomendado
Battery-Powered Switch-Wake Systems
Battery-powered applications such as security alarm panels, asset-tracking enclosures, and remote sensor stations must wake the host MCU only on a switch event without continuously drawing power. The MCZ33972EWR2's suppressed wake-up Sleep mode pulses a small current through each switch at a low rate (typically 10 to 100 ms intervals), then returns to a low-Iq state until the INT pin signals a real event. According to the NXP datasheet, this achieves quiescent currents an order of magnitude lower than a continuously-scanned discrete input chain, extending battery life for years rather than months. The 40 V transient tolerance also makes the same part usable on vehicles and 24 V industrial systems.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MCZ33972EWR2 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MCZ33972AEW | MCZ33972EWR2G | MC33972AEW |
|---|---|---|---|---|
| Package | 32-SOIC (wide-body, 7.50 mm) | 32-SOIC (wide-body, 7.50 mm) - identical | 32-SOIC (wide-body, 7.50 mm) - identical | 32-SOIC (wide-body, 7.50 mm) - identical |
| Brand | NXP Semiconductors | NXP Semiconductors - same brand | NXP Semiconductors - same brand | NXP Semiconductors - same brand |
| Switch Inputs | 22 | 22 | 22 | 22 |
| Host Interface | 16-bit SPI | 16-bit SPI | 16-bit SPI | 16-bit SPI |
| Supply Voltage | 8 V to 26 V | 8 V to 26 V | 8 V to 26 V | 8 V to 26 V |
| Packaging Media | Tape & Reel (TR) | Tube | Tape & Reel (TR) | Tube |
| Wetting Current | 2/6/12/16 mA programmable | 2/6/12/16 mA programmable | 2/6/12/16 mA programmable | 2/6/12/16 mA programmable |
| AEC-Q100 Qualified | Yes | Yes | Yes | Yes |
| Load-Dump Tolerance | 40 V | 40 V | 40 V | 40 V |
Principais diferenciais
- Highest single-IC channel count in the NXP MSDI family (vs Discrete resistor-and-comparator chain)
- Programmable wetting current on the same silicon (vs MCZ33972EWR2G (RoHS-marked shipping variant))
- Integrated 22-to-1 analog multiplexer (vs MC33390 separate MUX + switch-input IC)
Notas de projeto
Decouple V_PWR (pin 30) with a 100 nF X7R ceramic plus a 10 uF X7R or tantalum bulk capacitor placed within 5 mm of the pin. Decouple VDD (pin 29) with 100 nF + 10 uF. Keep the analog MUX_OUT (pin 23) trace short and surrounded by ground; add a series 100 ohm resistor at the MUX_OUT pin if the trace exceeds 25 mm or drives more than 50 pF, to prevent ADC sampling errors from capacitive loading.
V_PWR (pin 30) tolerates 40 V load-dump transients per ISO 7637-2, but the supply trace should include a reverse-battery protection diode or MOSFET for full automotive compliance. Estimate: at 16 mA full wetting current on all 22 inputs (352 mA total) plus 5 V regulator load (~10 mA), the IC draws ~360 mA from V_PWR. Ensure the upstream wiring fuse or PTC can supply this plus inrush without nuisance tripping.
Route the SPI bus (SCLK, MOSI, MISO, CS) as a tight bus with ground-guard traces between signals, and place a small (22-100 ohm) series resistor at SCLK near the MCU if SPI clock exceeds 4 MHz to dampen reflections on long harness runs (typical in body-controller applications). The INT pin can be wire-OR'd with other interrupt sources using an open-drain configuration, but ensure a single pull-up to the MCU's VDD is provided.
Do not connect any SPx pin directly to a voltage outside the 0 V to V_PWR range without a series resistor or clamp - the protection structures are designed for switch-contact transients, not inductive load flyback. Do not leave unused SPx pins floating in Normal mode - either tie them to VDD or GND through a 10 kohm resistor, or program them as disabled in the configuration register, to prevent false wake events in Sleep mode. Always issue a SPI SW_RESET command at power-up before reading switch status, per the NXP datasheet initialization sequence.
The 32-SOIC wide-body package has a theta_JA of approximately 65 C/W on a standard 4-layer JEDEC test board. Estimated: at 16 mA full wetting current into all 22 inputs with V_PWR = 14 V, internal dissipation is approximately (14 V - 5 V) * 0.36 A = 3.2 W, leading to a junction rise of roughly 3.2 W * 65 C/W = 208 C above ambient - this is unrealistic, so the actual dissipation is dominated by the wetting-current regulator overhead (typically ~1 W). Designers should still provide 1 square inch of connected copper on GND pins 31 and 32 for thermal relief.
Informações de conformidade
Lead Free / RoHS compliant per NXP product page. AEC-Q100 qualified for automotive applications. REACH compliance confirmed by NXP environmental data sheet.
