DSP
Товары (913)
DSPIC33FJ64MC706A-E/MR - 16-bit 40MIPS DSC 64KB | Microchip
The Microchip Technology DSPIC33FJ64MC706A-E/MR is a 16-bit digital signal controller (DSC) delivering 40 MIPS from a 40 MHz core, with 64 KB of flash program memory and 16,384 words of RAM, housed in a 64-pin QFN with exposed pad (MR) package rated for -40C to +125C extended temperature operation. A digital signal controller combines the deterministic interrupt response and peripheral set of a microcontroller with the multiply-accumulate computational throughput of a DSP. In the power-management hierarchy of embedded systems, a DSC sits between a general-purpose MCU and a dedicated DSP: it executes real-time control loops, such as field-oriented control of motors, while managing communication, sensing, and system supervision on the same silicon. Key features include the 16-bit dsPIC33F core with DSP instruction extensions, an on-chip CAN 2.0B controller for industrial networking, motor-control PWM peripherals capable of complementary outputs with dead-time insertion, and advanced analog integration for sensing. The dsPIC33FJ64MC706A family is explicitly optimized for motor control applications by Microchip, covering brushless DC, single- and 3-phase induction, and switched reluctance motor architectures. Technically, the device executes up to 40 million instructions per second at 3.0V to 3.6V operation, with a 24-bit instruction word architecture. Seamless migration paths exist to PIC24 MCU and dsPIC30F DSC devices in similar packages, protecting software investment. The extended -40C to +125C E-temperature suffix suits industrial enclosures, traction cabinets, and under-hood-adjacent electronics where ambient temperatures exceed commercial ratings. Typical applications include brushless DC motor drives, 3-phase induction motor inverters, uninterruptible power supplies (UPS), switched reluctance motor controllers, and power-factor-correction stages where the PWM engine, ADC, and CAN bus operate in a coordinated real-time loop. A key design consideration is supply integrity: the QFN exposed pad must be soldered to a solid ground plane, and decoupling capacitors placed directly at each VDD/VSS pair to support the 40 MHz switching currents during simultaneous PWM edge transitions. This page synthesizes distributor pricing, drop-in same-package alternatives, pinout guidance, and practical design notes not consolidated in the manufacturer datasheet.
DSPIC33FJ64MC706AT-I/PT - 16-bit 40MIPS DSC 64KB Flash | Microchip
The Microchip Technology DSPIC33FJ64MC706AT-I/PT is a 16-bit digital signal controller (DSC) delivering 40 MIPS performance with 64KB (64K x 8) of Flash program memory and 16KB of RAM, housed in a 64-pin TQFP (10x10 mm) package. A digital signal controller combines the computational architecture of a DSP with the peripheral set and ease of use of a microcontroller. Within the power-management hierarchy of embedded systems, the DSC sits between general-purpose MCUs and dedicated DSPs: it executes deterministic control loops (such as field-oriented motor control) while simultaneously handling communication, timing, and analog acquisition tasks on a single chip. The dsPIC33F family from Microchip Technology is a widely adopted 16-bit DSC platform for these mixed control-plus-connectivity designs. Key features of this device include the 40 MIPS dsPIC33F core with DSP engine and barrel shifter, 16KB of on-chip SRAM, 8-channel DMA controller, and 11 timers. Analog capability is provided by a 16-channel, 10-bit/12-bit ADC supporting high-rate simultaneous sampling - essential for current and voltage sensing in motor drives. Five external interrupt sources and multiple serial ports round out the I/O capability. The MC706 variant belongs to the motor-control (MC) subfamily, which integrates motor-control PWM peripherals suited to inverter and converter control. The CMOS process with low-power modes (Idle and Sleep) allows battery-powered and thermally constrained designs to reduce average current draw while retaining fast wake-up for real-time control loops. Typical applications include three-phase motor control (BLDC, PMSM, AC induction), digital power supplies and solar inverters, and industrial automation nodes that need deterministic control loops alongside serial communication. The 3.0V to 3.6V supply range matches standard 3.3V industrial rails. When designing with this device, budget the 16KB RAM carefully - control-loop state, DMA buffers, and communication stacks must share it; larger buffer requirements may favor the 128KB Flash variants of the same package. The industrial temperature rating (-40C to +85C) and RoHS3 compliance simplify qualification for factory environments. This page synthesizes distributor pricing, drop-in same-package alternatives, design notes, and application guidance not consolidated in the manufacturer datasheet.
DSPIC33FJ64MC706T-I/PT - 16-bit DSC, 40 MIPs, 64KB Flash | Microchip
The Microchip Technology DSPIC33FJ64MC706T-I/PT is a 16-bit digital signal controller (DSC) delivering 40 MIPs of performance, 64KB (64K x 8) of Flash program memory, and 69 I/O, housed in a 64-pin TQFP (10x10 mm) surface-mount package rated from -40C to +85C. A digital signal controller combines the deterministic control flow of a microcontroller with the multiply-accumulate (MAC) hardware of a DSP core. In the power-management hierarchy, the dsPIC33F family sits between general-purpose 16-bit MCUs (such as the PIC24) and standalone DSPs, offering a single-chip solution for control loops that must execute fast math while managing peripherals, communication, and I/O. Key features include the 16-bit dsPIC33F core with DSP engine (40-bit accumulators, dual 16-bit working registers), 64KB Flash and 8KB SRAM, an internal fast RC oscillator with PLL allowing 40 MIPS operation without an external crystal, and industrial temperature coverage (-40C to +85C). The supply range is 3.0V to 3.6V (3.3V nominal), and the part is lead-free and RoHS-compliant per distributor listings. The MC706 variant of the dsPIC33FJ64MC family is optimized for motor control and digital power, integrating peripherals such as PWM modules, high-speed ADCs, and communication interfaces (UART, SPI, I2C, ECAN per family datasheet) that allow field-oriented control (FOC) and digital power loops to be executed at 40 MIPS with headroom. Typical applications include three-phase motor drives (BLDC, PMSM, ACIM), switch-mode power supplies and digital power conversion, power inverters and UPS systems, and sensor signal processing in industrial automation. The 69 available I/O on the 64-TQFP gives enough parallel interface capability for displays, keyboards, and companion ICs. Design consideration: the 3.0V to 3.6V supply window means this DSC is not 5V tolerant across all pins by default - verify per-pin tolerances in the manufacturer datasheet and add proper decoupling (multiple 0.1uF ceramics plus bulk capacitance) at each VDD/VSS pair. This page synthesizes distributor pricing, drop-in alternatives, application guidance, and engineering design notes not found in the standard manufacturer datasheet, as of 2026-09-27.
DSPIC33FJ64MC710AT-I/PT - 16-bit 40MIPS DSC 64KB Flash | Microchip
The Microchip Technology DSPIC33FJ64MC710AT-I/PT is a 16-bit digital signal controller (DSC) from the dsPIC33FJ64MC710A motor control family, delivering 40 MIPS performance with 64KB (64K x 8) of Flash program memory and 16KB of RAM, housed in a 100-pin TQFP (12x12 mm, 0.5 mm pitch) surface-mount package rated from -40C to +85C. A digital signal controller combines the compute architecture of a microcontroller with the DSP engine of a digital signal processor. In the power-management hierarchy, the dsPIC33F family sits between general-purpose MCUs (such as the PIC24) and dedicated DSPs, adding a DSP multiply-accumulate engine, 8-channel DMA, and motor-control-specific peripherals (PWM with dead-time insertion, quadrature encoder interface) to a familiar MCU toolchain. Key features include a 16-bit dsPIC33F core executing up to 40 MIPS, 64KB self-programmable Flash with in-circuit programming, and 16KB data RAM. The device integrates a 10-bit high-speed ADC, multiple UART, SPI and I2C serial ports, CAN 2.0B for industrial networking, and DMA channels that offload data movement from the CPU. According to Microchip product pages, the family targets brushless DC, single and 3-phase induction, and switched reluctance motor control. Technical depth: the dsPIC33FJ64MC710A core supports 40 MHz maximum clock operation (40 MIPS at 3.3V supply), with DSP instructions including 40-bit accumulators, dual operand fetch, and modulo/bit-reversed addressing. The 8-channel DMA and nine timers support deterministic real-time control loops, while the Output Compare/PWM modules generate complementary waveform pairs for inverter bridges. Per the Microchip USA listing, the related ATH grade variant is built on CMOS technology meeting AEC-Q100 automotive requirements. Typical applications include brushless DC (BLDC) and PMSM motor drives, solar inverters, digital UPS and power-factor-correction converters, and industrial automation nodes requiring CAN connectivity alongside DSP-class control loops. Design consideration: at 40 MIPS the device is sensitive to supply integrity; place 0.1 uF decoupling at all VDD/VSS pairs and keep the switching nodes of the power stage away from the analog front end to protect ADC accuracy. This page synthesizes distributor pricing, same-brand drop-in alternatives, pinout guidance, and practical design notes not found in the manufacturer datasheet.
DSPIC33FJ64MC710T-I/PT - 16-bit 40 MIPS DSC, 64KB Flash | Microchip
The Microchip Technology DSPIC33FJ64MC710T-I/PT is a 16-bit digital signal controller (DSC) from the dsPIC33FJ64MC710 motor-control family, delivering up to 40 MIPS performance, 64KB (64K x 8) of FLASH program memory, 16KB of RAM, and 3.3V operation (3V to 3.6V supply), housed in a 100-pin TQFP (12 x 12 mm) surface-mount package rated from -40C to +85C. A digital signal controller combines the control peripherals of a microcontroller with the multiply-accumulate (MAC) DSP engine of a digital signal processor. In the power-management hierarchy, a DSC sits between a general-purpose MCU and a dedicated DSP: it runs deterministic control loops for power conversion while retaining flexible I/O, timers, and communication peripherals. The dsPIC33F family belongs to Microchip's 16-bit architecture portfolio and offers seamless migration options to PIC24F, PIC24H MCUs, and dsPIC30F DSCs in similar packages. Key features of this part include the 40 MIPS dsPIC33F core at 3.3V, 69 I/O ports for high pin-count boards, an integrated DSP engine for fast FIR filtering and PID control, and industrial temperature qualification (-40C to +85C). The motor-control subclass (MC) integrates dedicated PWM peripherals designed for inverter and motor-drive applications. Architecturally, the dsPIC33F core uses a modified Harvard 16-bit pipeline that executes most instructions in a single cycle, with two 40-bit accumulators and a 17-bit x 17-bit single-cycle MAC for DSP math. FLASH program memory allows field reprogramming, and the 3V to 3.6V supply range supports standard 3.3V rails. Typical applications include sensorless BLDC and PMSM motor drives, digital power supplies (PFC, LLC), industrial automation, and embedded control systems requiring DSP-grade math with MCU-style peripherals. Design consideration: the 100-TQFP 12 x 12 mm package requires careful decoupling of all VDD/VSS pairs and a solid ground plane to maintain signal integrity at 40 MIPS clock rates. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.
DSPIC33FJ64MC802-E/MM - 16-bit DSC, 40 MIPS, 64KB Flash | Microchip
The Microchip Technology DSPIC33FJ64MC802-E/MM is a 16-bit digital signal controller (DSC) delivering 40 MIPS performance, 64KB (64K x 8) of FLASH program memory, and automotive-grade AEC-Q100 qualification in a 28-pin QFN-S (6x6 mm) exposed-pad package operating from a 3.3V supply. A digital signal controller combines the deterministic interrupt handling and peripherals of a microcontroller with the mathematical throughput of a DSP. Within the power-management hierarchy, the dsPIC33F family sits above general-purpose MCUs (such as the PIC18 series) and below 32-bit MCUs, targeting closed-loop control applications that rely on high-speed, repetitive computations. According to Microchip, the dsPIC33F devices are pin compatible with the PIC24HJ family and share a very high degree of compatibility with the dsPIC30F family, enabling seamless migration. Key features include the modified Harvard 16-bit core with DSP engine (barrel shifter, 17-bit x 17-bit multiplier, 40-bit accumulator), motor-control PWM peripherals, and advanced analog-to-digital conversion. The -E temperature suffix guarantees operation from -40C to +125C, supporting under-hood and industrial environments. The architecture couples a 16-bit instruction width with 16-bit wide data RAM and single-cycle MAC operations, making it well suited to field-oriented motor control where Clarke/Park transforms execute every PWM cycle. Hardware division, modulo addressing, and DO/REPEAT loops further accelerate control math. Typical applications include brushless DC and PMSM motor drives, digital power supplies (LLC, PFC, buck), and sensorless FOC algorithms requiring deterministic 40 MIPS throughput. Design consideration: use the QFN exposed pad as the primary ground connection, soldered to a solid VSS copper pour, to minimize ground bounce during simultaneous PWM switching events. This page synthesizes distributor pricing data, pin-compatible family alternatives, and practical design notes not found in the manufacturer datasheet alone.
DSPIC33FJ64MC802-E/SP - 16-bit DSC 40 MIPS 64KB Flash | Microchip
The Microchip DSPIC33FJ64MC802-E/SP is a 16-bit digital signal controller (DSC) combining a dsPIC33F DSP core running at up to 40 MIPS with 64 KB (22K x 24) Flash program memory, a 3.0V to 3.6V supply range, and a 28-pin SPDIP through-hole package rated for the extended -40C to +125C temperature range. A digital signal controller is a hybrid class of power management and embedded processing IC that merges the computational engine of a digital signal processor (DSP) with the peripherals and architecture of a microcontroller (MCU). In the embedded control hierarchy, the DSC sits between a general-purpose microcontroller and a dedicated DSP, offering single-cycle MAC, barrel shifting, and hardware divide - capabilities targeted at high-speed, repetitive computations such as field-oriented motor control and digital power conversion. Key features include 40 MIPS throughput from an on-chip PLL, two PWM generators with independent timebases and complementary outputs for motor control, the Peripheral Pin Select (PPS) capability that remaps digital peripherals to any compatible pin, and a 10-bit, 1.1 Msps ADC suited to closed-loop current sensing. The -E/SP ordering code denotes the extended-temperature grade in the 28-SPDIP package, packaged in tubes for through-hole assembly. The dsPIC33FJ64MC802 belongs to Microchip's 16-bit dsPIC33F motor-control family and is pin compatible with the PIC24HJ family, sharing a high degree of code compatibility across the 16-bit portfolio. Development is supported by MPLAB X IDE and XC16 compiler toolchain with hardware debug via ICD/Real ICE. Typical applications include brushless DC and PMSM motor drives, switched-mode power supplies, digital ballasts, battery charging, and industrial sensing nodes requiring real-time signal processing in a compact, low-pin-count footprint. Design consideration: the 3.3V-only supply (3.0V to 3.6V) requires level shifting for 5V industrial peripherals; MCLR must be driven below VDD limits during programming. This page synthesizes distributor availability data, pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet alone.
DSPIC33FJ64MC802-H/SO - 16-bit DSC, 64KB Flash, 40MHz | Microchip
The Microchip Technology DSPIC33FJ64MC802-H/SO is a 16-bit digital signal controller (DSC) with 64KB of Flash program memory, 40MHz internal clock operation, and a 3.0V to 3.6V supply range, housed in a 28-pin SOIC package. It combines MCU control with DSP capability in a single core. A digital signal controller is a hybrid device that merges the deterministic control features of a microcontroller (interrupts, peripherals, Flash memory) with the high-speed, repetitive computation capability of a digital signal processor (DSP engine, MAC instructions). Within the power-management hierarchy, DSCs such as the dsPIC33F family sit above basic MCUs and are widely used wherever fast control loops - such as current loops in motor drives - must execute at microsecond intervals. Key features of this device include the Motor Control PWM module for precision motor drive, a DMA controller that offloads data transfers from the CPU, and advanced analog peripherals for sensing feedback signals. Per Microchip product data, the family is pin compatible with the PIC24HJ family and shares a high degree of compatibility with dsPIC30F and dsPIC33F devices, enabling seamless migration across the portfolio. Architecturally, the dsPIC33F employs a modified Harvard 16-bit core optimized for high-speed, repetitive computations as well as control. Program memory is Flash-based (64KB on this variant) with the family scaling up to 128KB Flash and 16K SRAM, while the DSP instruction set accelerates filtering and transform-based algorithms used in digital power and sensor processing. Typical applications include brushless DC (BLDC) and permanent-magnet motor control, digital power supplies (PFC, LLC), and sensor signal conditioning where the on-chip analog and DSP engine handle fast feedback loops. The CAN-capable, DMA-equipped architecture also suits industrial automation nodes. Design consideration: the 3.0V-3.6V supply requires a regulated 3.3V rail; the -H suffix denotes the wider temperature rating, so verify thermal margin in enclosed motor-drive enclosures. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes beyond what the manufacturer datasheet alone provides.
DSPIC33FJ64MC802-I/MM - 16-bit DSC 40MIPS 64KB Flash | Microchip
The Microchip Technology DSPIC33FJ64MC802-I/MM is a 16-bit digital signal controller (DSC) delivering 40 MIPS at 40 MHz, with 64 KB of Flash program memory and 8 DMA channels, housed in a 28-lead QFN-S (6x6 mm) package. A digital signal controller combines the computational throughput of a digital signal processor with the peripheral integration and interrupt-driven determinism of a microcontroller. In the power-management hierarchy of embedded systems, the DSC sits above general-purpose MCUs where motor control, digital power conversion, and sensor-processing loops demand multiply-accumulate performance per clock cycle. Key features include the dsPIC33F 16-bit modified Harvard architecture with DSP instruction support (MAC, DSP multiply), 40 MIPS maximum execution speed, 64 KB self-programming Flash, and eight DMA channels that move data without CPU intervention. Advanced analog peripherals and motor-control PWM outputs target precision control applications directly. The architecture is pin compatible with the PIC24HJ family and shares a high degree of compatibility with dsPIC30F and dsPIC33F devices, allowing seamless migration between 16-bit Microchip platforms. The CMOS core operates from a 3 V to 3.6 V supply, and the industrial temperature grade (suffix I) covers -40C to +85C. In-circuit serial programming and debug are supported by standard Microchip tools, including PICKIT and ICD programmers, as well as SEGGER tooling. Typical applications include brushless DC and permanent-magnet motor control, digital power supplies (PFC, LLC), and sensor signal processing in industrial automation. Design consideration: keep the oscillator circuit within 12 mm of the device clock pins with load capacitors adjacent to the crystal, as recommended in the Microchip datasheet, to preserve start-up margin. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not consolidated in the manufacturer datasheet.
DSPIC33FJ64MC802T-I/SO - 16-Bit DSC 64KB Motor Control | Microchip
The Microchip Technology DSPIC33FJ64MC802T-I/SO is a 16-bit Digital Signal Controller (DSC) from the dsPIC33F family, delivering 40 MIPS at 3.0 V to 3.6 V with 64 KB of Flash program memory and 16 KB of SRAM, housed in a 28-pin SOIC (0.295", 7.50 mm) surface-mount package. It integrates a motor-control PWM module, a 10-bit ADC, and a CAN module, making it a single-chip solution for embedded motor control and digital power conversion. A Digital Signal Controller (DSC) is a hybrid device that combines the real-time control peripherals and interrupt behavior of a microcontroller (MCU) with the single-cycle multiply-accumulate (MAC) arithmetic and barrel shifter of a digital signal processor (DSP). In the system hierarchy, a DSC sits between a general-purpose MCU and a dedicated DSP: it is a member of the embedded processor and controller category, under the broader semiconductor and integrated circuit taxonomy. The dsPIC33F architecture executes most instructions in a single cycle, enabling deterministic control loops that pure MCUs cannot match. Key differentiators of the DSPIC33FJ64MC802T-I/SO include its 40 MIPS core, 64 KB Flash, 16 KB SRAM, 8-channel DMA, and a dedicated motor-control PWM with complementary outputs and dead-time insertion. The device is pin-compatible with the PIC24HJ family and highly compatible with dsPIC30F devices, enabling seamless migration across Microchip's 16-bit portfolio. The device uses a modified Harvard architecture with a 16-bit data path and 24-bit instruction words, supported by a barrel shifter and hardware divider. Its nanoWatt power management supports multiple sleep and idle modes for energy-sensitive designs, while the on-chip CAN module enables industrial networking without an external controller. Typical applications include three-phase brushless DC (BLDC) motor control, field-oriented control (FOC) of permanent-magnet synchronous motors (PMSM), digital power supplies, and automotive sensorless motor drives. The combination of 40 MIPS throughput and hardware PWM makes it well suited to closed-loop current and speed control at switching frequencies up to tens of kHz. When designing with this device, keep the analog supply (AVDD/AVSS) well decoupled from the digital rail and route the motor-control PWM outputs away from the ADC input traces to preserve conversion accuracy. The 28-pin SOIC package limits available I/O, so peripheral pin selection (PPS) should be planned early. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers a single reference for selection, replacement, and layout decisions.
DSPIC33FJ64MC804-E/ML - 16-bit 40 MIPS DSC 64KB Flash | Microchip
The Microchip Technology DSPIC33FJ64MC804-E/ML is a 16-bit digital signal controller (DSC) delivering 40 MIPS execution speed, 64 KB (64K x 8) of Flash program memory, and 16 KB (16K x 8) of SRAM, housed in a 44-pin QFN (8 x 8 mm) package. It operates from a 3 V to 3.6 V single supply and is rated for the extended -40C to +125C temperature range. A digital signal controller combines the computation throughput of a DSP engine with the peripheral set and ease of use of a microcontroller. Within the power-management hierarchy, the dsPIC33F family sits between general-purpose MCUs and standalone DSPs: it is a 16-bit processor core with integrated DSP multiply-accumulate instructions, making it a single-chip solution for control loops and signal processing. Key features of this part include a 16-bit modified Harvard architecture running up to 40 MIPs, motor-control PWM and advanced analog peripherals, and pin compatibility with the PIC24HJ family, which eases migration between controller families. The 64 KB Flash supports in-circuit self-programming, and the 16 KB SRAM provides headroom for control algorithms and buffering. The MC804 subfamily is specifically architected for precision motor control: dedicated motor-control PWM outputs, high-speed ADC sampling, and DSP instructions for field-oriented control (FOC) transforms. The advanced analog block integrates a fast ADC and comparators that offload the core in current-loop applications. Typical applications include brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) drives, switch-mode power supplies and power factor correction, digital power metering, and industrial automation nodes where high-speed repetitive computation is required. When designing with this device, decouple the 3.3 V rail locally at each VDD/VSS pair and follow the Microchip family reference manual for oscillator layout, since a stable 40 MIPS clock is central to control-loop timing. This page synthesizes distributor pricing, drop-in alternatives, comparison data, and practical design notes not found in the manufacturer datasheet.
DSPIC33FJ64MC804-E/PT - 16-bit DSC 64KB Flash 40MIPS | Microchip
The Microchip Technology DSPIC33FJ64MC804-E/PT is a 16-bit Digital Signal Controller (DSC) combining a dsPIC33F core running at up to 40 MIPS, 64 KB of Flash program memory, and 8 KB of SRAM, housed in a 44-pin TQFP (10x10 mm) surface-mount package with an extended -40C to +125C operating temperature range. A Digital Signal Controller is a hybrid device that merges the deterministic control structure of a microcontroller with the high-speed multiply-accumulate computation of a DSP. Within the power-management hierarchy, the DSC sits between a general-purpose MCU and a dedicated DSP: it belongs to the class of 16-bit embedded processors, which in turn belong to the broader family of microcontrollers and semiconductor integrated circuits. The dsPIC33F family is pin compatible with the PIC24HJ family, allowing designers to move between control- and DSP-optimized variants without changing the PCB. Key features include 64 KB of self-programmable Flash, 8 KB of RAM, 8 DMA channels for peripheral data transfer without CPU intervention, dedicated motor control PWM peripherals, and advanced analog modules for sensor feedback loops. The device operates from a 3.0 V to 3.6 V single supply, with a maximum clock rate of 40 MHz (40 MIPS), matching the needs of closed-loop motor and power-conversion algorithms executed in microseconds. Architecturally, the dsPIC33F core pairs a 16-bit RISC pipeline with DSP-engine instructions (MAC, DSP multiply, barrel shifter), enabling high-speed repetitive computations such as FOC (field-oriented control), PI loops, and digital filtering. Code protection features safeguard intellectual property in the Flash array. Typical applications include brushless DC and PMSM motor drives, digital power supplies (LLC, totem-pole PFC), solar inverters, and industrial sensing and control nodes. The MC (Motor Control) peripheral set and DMA make it a strong fit where precise PWM generation and fast ADC sampling must run concurrently. Design consideration: keep the supply strictly within 3.0 V to 3.6 V and decouple every VDD/VSS pair with 0.1 uF ceramics placed within 2 mm of the pins; the 44-TQFP thermal pad region benefits from solid ground planes for analog accuracy. This page synthesizes verified distributor data, drop-in alternatives, and design guidance not found in the manufacturer datasheet, with pricing verified as of 2026-09-27.
DSPIC33FJ64MC804-H/ML - 16-bit DSC, 64KB Flash, 40 MIPS | Microchip
The Microchip Technology DSPIC33FJ64MC804-H/ML is a 16-bit digital signal controller (DSC) delivering 40 MIPS at 3.3V with 64KB (64K x 8) of Flash program memory and a 44-pin QFN (8x8 mm) exposed-pad package. A digital signal controller combines the compute architecture of a digital signal processor with the peripheral set and ease of use of a microcontroller. Within the power-management hierarchy, a DSC is a class of embedded processor that sits between a general-purpose MCU and a dedicated DSP: it executes high-speed, repetitive mathematical loops (PID control, transforms, filtering) while simultaneously managing real-time I/O such as PWM generation and ADC sampling. The dsPIC33F family is Microchip's 16-bit DSC line, pin-compatible with the PIC24HJ MCU family and highly code-compatible with the older dsPIC30F family for seamless migration. Key features of the DSPIC33FJ64MC804-H/ML include the dsPIC33F core operating at up to 40 MIPS, motor-control PWM peripherals purpose-built for precision motor control, an advanced analog front end with high-speed 12-bit ADC, and a wide 3.0V to 3.6V supply range (3.3V nominal). The -H temperature grade supports -40C to +125C operation, making it suitable for demanding industrial environments. Architecturally, the device pairs the 16-bit modified Harvard core with DSP engine instructions (MAC, DSP multiply) and zero-overhead loops, so control-law computations execute deterministically without interrupt jitter. Flash program memory is 64KB and SRAM is sized per the family datasheet (family devices support up to 16K SRAM across the family). Multiple PGECx/PGEDx pin pairs support In-Circuit Serial Programming (ICSP) with any pair usable, provided the clock and data pins are used as a matched pair. Typical applications include brushless DC and PMSM motor drives, switched-mode power supplies, digital lighting ballasts, and embedded industrial control where sensor-loop and PWM timing must be tightly coupled. Design consideration: use only one matched PGECx/PGEDx pair for ICSP, and decouple the 3.3V rail with low-ESR ceramics placed close to the QFN exposed pad, which must be soldered to a grounded thermal pad for both electrical and thermal integrity. This page synthesizes distributor pricing data, verified drop-in alternatives, datasheet-sourced specifications, and practical design notes not consolidated in the manufacturer datasheet alone.
DSPIC33FJ64MC804-H/PT - 16-bit DSC 64KB Flash Motor Control | Microchip
The Microchip Technology DSPIC33FJ64MC804-H/PT is a 16-bit Digital Signal Controller (DSC) combining a dsPIC33F core running at up to 40 MIPS with 64KB (22K instructions x 24-bit) Flash program memory and 16KB SRAM, housed in a 44-pin TQFP (PT) package rated from -40C to +150C. A Digital Signal Controller merges the computational power of a DSP with the peripheral set and ease of use of a microcontroller. Within the semiconductor hierarchy, the dsPIC33F family sits under the 16-bit MCU/DSC category, itself a branch of embedded processors, and is designed for control loops that demand both fast math and rich on-chip analog and PWM peripherals. Key features include a modified Harvard 16-bit architecture with DSP engine (17-bit x 17-bit single-cycle MAC, 40-bit accumulators), Motor Control PWM with complementary outputs and dead-time insertion, a 10-bit ADC capable of 1.1 Msps operation, and connectivity peripherals such as CAN 2.0B, UART, SPI and I2C. DMA controllers offload data movement from the CPU, keeping loop timing deterministic. Technically, the device operates from a 3.0V to 3.6V supply and executes from zero-wait-state Flash at 40 MIPS via an on-chip PLL from an external or internal oscillator. The H temperature grade extends operation to +150C, supporting motor drives mounted near hot electromechanical assemblies. Pin compatibility with the PIC24HJ family allows easy migration between general-purpose and motor-control firmware platforms. Typical applications include brushless DC and PMSM motor control with sensorless field-oriented control, switched-mode power supplies and digital power conversion, and automotive/industrial sensing nodes requiring CAN networking at elevated ambient temperatures. A key design consideration is power-supply sequencing and decoupling: place 0.1uF ceramics at every VDD/VSS pair and use the dedicated AVDD/AVSS pins with an RC filter for ADC accuracy. This page synthesizes distributor pricing, drop-in alternatives, design notes, and FAQ content not found in the manufacturer datasheet. Pricing shown is a distributor estimate as of 2026-09-27; confirm live stock and pricing before ordering.
DSPIC33FJ64MC804T-I/PT - 16-bit 40 MIPS DSC 64KB Flash | Microchip
The Microchip Technology DSPIC33FJ64MC804T-I/PT is a 16-bit digital signal controller (DSC) delivering 40 MIPS performance, 64KB of Flash program memory, 8KB of SRAM, and an integrated Motor Control PWM peripheral, housed in a 44-pin TQFP (10x10 mm) package rated for -40C to +85C operation. A digital signal controller combines the computational throughput of a digital signal processor with the deterministic control and peripheral set of a microcontroller. Within the power-management hierarchy, a DSC sits above general-purpose MCUs in signal-processing capability, making the dsPIC33F family a bridge between the PIC24HJ MCU family and dedicated DSP devices. Microchip confirms that dsPIC33F devices are pin compatible with PIC24HJ and share a high degree of compatibility with dsPIC30F, enabling seamless migration across these families. Key features include a 16-bit modified Harvard architecture executing up to 40 MIPS, 64KB (64K x 8) of self-programmable Flash, and an 8-channel DMA controller that offloads data movement from the CPU. The peripheral set includes multiple timers (5 timers per Microchip USA product data), two serial I/O interfaces, and Motor Control PWM outputs targeted at precision motor control per the datasheet title. Architecturally, the dsPIC33FJ64MC804 employs multiple internal buses, a barrel shifter, DSP multiply-accumulate hardware, and boundary-scan support. Supply voltage is specified at 3 V to 3.6 V per digchip specifications data, and the CMOS process delivers low power consumption for embedded control nodes. The 44-TQFP (10x10) package suits both prototyping and volume surface-mount assembly. Typical applications include precision motor control (BLDC, PMSM, ACIM drives), digital power supplies and inverters, and industrial sensors and instrumentation that rely on high-speed, repetitive computation. The MC suffix denotes the Motor Control peripheral family, with ADC and analog support for closed-loop current sensing. Designers should decouple the 3.3 V rail locally and account for Flash erase/write endurance when using self-programming. Confirm ADC channel allocation early, as the 44-pin package multiplexes many analog functions. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
MC56F8025MLD - 16-Bit DSC 32MHz 32KB Flash 44-LQFP | NXP
The NXP MC56F8025MLD is a 16-bit digital signal controller (DSC) based on the 56800E core, running at 32 MHz with 32KB (16K x 16) of on-chip flash program memory, 4KB (2K x 16) of RAM, and 35 general-purpose I/O lines, housed in a 44-pin LQFP (10 x 10 mm) surface-mount package. A digital signal controller combines the computation throughput of a digital signal processor with the programming model, interrupt structure, and peripherals of a microcontroller. In the embedded hierarchy, the MC56F8025MLD sits between general-purpose MCUs and dedicated DSPs: it is a member of the NXP 56F8xxx DSC family, which in turn belongs to the broader category of embedded microcontroller ICs for real-time control. Key features include the dual Harvard-style 56800E architecture with three parallel execution units capable of up to six operations per instruction cycle, 32KB of flash memory supporting in-circuit reprogramming, and connectivity peripherals including I2C, LINbus, SCI, and SPI. The part operates over an industrial temperature range and uses gull-wing terminals on a square LQFP body. Technically, the 56800E core executes an MCU-style, C-compiler-friendly instruction set while providing DSP instructions such as single-cycle MAC, hardware loop instructions, and bit-manipulation capability. This allows a single device to run both the control loop (PID, state machines) and signal-processing tasks (filtering, transforms) without a second processor, reducing board area and BOM cost in motor and power-conversion designs. Typical applications include digital power supplies and power factor correction, BLDC/PMSM and stepper motor control, AC induction motor drives, uninterruptible power supplies, and industrial appliances requiring fast closed-loop control. Design consideration: budget flash and RAM carefully - at 32KB/4KB the device targets compact control loops, and C code with heavy DSP libraries can exhaust memory quickly; enable compiler optimization and consider fixed-point math. This page synthesizes distributor pricing, availability, alternatives, and practical design notes not found in the manufacturer datasheet, with data verified as of 2026-10-18.
MC56F8156VFV - 16-bit DSC 80MHz 256KB | NXP 56F815x
The NXP MC56F8156VFV is a 16-bit Digital Signal Controller (DSC) from the 56F815x family, integrating a 56800E core with DSP and microcontroller functionality on a single device, operating at 80 MHz, housed in a 144-pin LQFP (20x20 mm) package. It delivers up to 80 MIPS of performance, features 256 KB of program Flash and up to 36 KB of unified data/parameter RAM, and targets industrial temperature grade operation from -40C to +105C. A Digital Signal Controller (DSC) is a hybrid architecture that combines a microcontroller's deterministic control peripherals with a Digital Signal Processor (DSP)'s multiply-accumulate (MAC) throughput. The 56800E core in the MC56F8156VFV executes both control code and DSP kernels in a single thread, eliminating the dual-chip DSP+MCU paradigm common in motor control designs. Within the broader taxonomy, the MC56F8156VFV sits as DSC -> microcontroller -> embedded processor -> semiconductor IC. Key features include on-chip peripherals such as PWM channels suitable for 3-phase motor drive, 12-bit ADCs with sub-microsecond conversion, quadrature decoders for position feedback, CAN 2.0B, SCI, SPI, I2C, and a 6-channel timer. Programmable memory protection and JTAG/OnCE debug enable robust embedded firmware deployment. The 144-LQFP package offers generous I/O for multi-axis motion applications. Architecturally, the 56800E core pairs a Harvard bus with unified 16-bit data and 16-bit instruction paths, plus a 36-bit accumulator for high-dynamic-range DSP arithmetic. Dual on-chip regulators and brown-out detection support direct industrial 3.3V/5V supply operation. Built-in temperature sensor and dedicated PWM fault inputs simplify hardware safety implementation. Typical applications include 3-phase AC induction and BLDC motor drives, digital power conversion, industrial inverters, servo control, and photovoltaic inverter control loops. The wide operating temperature and CAN connectivity suit factory automation environments. When designing with the MC56F8156VFV, ensure that decoupling capacitors are placed close to each supply pin pair, the analog supply is filtered, and the exposed thermal considerations are respected under high peripheral activity. Use Freescale/NXP CodeWarrior with Processor Expert for code generation to accelerate bring-up. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
MC56F8166VFV - 16-Bit 120MHz DSP Controller | NXP
The NXP Semiconductors MC56F8166VFV is a 16-bit 56800E digital signal controller with 512 KB Flash, a 120 MHz maximum clock, and 144 leads in a 20 mm × 20 mm LQFP package. It combines a CISC processor core with embedded signal-processing and control peripherals for industrial embedded designs. A digital signal controller is a microcontroller-family semiconductor optimized for real-time control and high-speed data manipulation. In the product hierarchy, it sits between a general-purpose microcontroller and a dedicated digital signal processor. The MC56F8166VFV is suited to applications where deterministic control, peripheral integration, and software-configurable signal processing are more important than a high-pin-count general-purpose processor platform. The verified device information identifies the 56800E architecture, 16-bit processing, 512 KB Flash organized as 256K × 16, a 60 MHz listing in the distributor result, and a 120 MHz maximum operating frequency in the datasheet search result. The discrepancy is recorded rather than resolved because the supplied sources do not clarify whether the 60 MHz figure is a bus or listing-specific frequency. Supply voltage is listed as 2.25 V to 2.75 V, and the package is a 144-pin square LQFP measuring 20 mm × 20 mm. The MC56F8166VFV family is appropriate for motor-control systems, power-conversion control, industrial automation, digital signal processing, and embedded control platforms. Its Flash memory supports embedded firmware storage, while the high-speed processing core can execute control algorithms and manage real-time peripherals. The 144-pin package provides substantial external connectivity compared with smaller microcontroller packages, although the exact peripheral mapping requires the manufacturer datasheet. Designers should verify the device datasheet before layout because the supplied data confirms the package and core specifications but does not provide a complete verified pinout, peripheral list, memory map, electrical limits, or application reference design. In particular, power rails, decoupling, clocking, programming, and unused-pin requirements must be taken directly from the official device documentation. This page distinguishes verified facts from missing engineering data and does not infer unprovided specifications. This page consolidates verified distributor identity, datasheet references, package information, application context, and procurement metadata into an engineering-oriented product record. It is designed for engineers comparing control-processor options, checking package and memory constraints, and locating source documents without treating unsupported numbers as guaranteed specifications.
MC56F8322MFA60 - 60MHz 16-bit DSC 48-LFQFP | NXP Semiconductors
The NXP Semiconductors MC56F8322MFA60 is a 16-bit Digital Signal Controller (DSC) running at 60 MHz (60 MIPS) based on the 56800E Harvard-style core, delivered in a 48-pin LFQFP (7x7 mm) gull-wing surface-mount package. The device integrates DSP-class signal processing with an MCU-style programming model, executing up to six operations per instruction cycle through three parallel execution units, and is offered in an automotive temperature grade for demanding embedded control applications. A Digital Signal Controller (DSC) is a hybrid processor class that sits between a microcontroller (MCU) and a digital signal processor (DSP). In the broader taxonomy, the MC56F8322 belongs to: DSC -> DSP -> microprocessor -> semiconductor. DSCs combine deterministic interrupt-driven control (typical of MCUs) with deterministic, high-throughput numeric computation (typical of DSPs) on a single die, eliminating the cost and complexity of separate processor + DSP chip sets in motor control and power-conversion systems. Key features of the MC56F8322MFA60 include 60 MHz core frequency delivering 60 MIPS, on-chip Flash program memory, on-chip data RAM, a multi-channel PWM module suitable for three-phase motor drive, dual 12-bit ADCs, and a rich set of serial peripherals (SCI, SPI, I2C, CAN). The 56800E instruction set is C-compiler friendly, enabling rapid development of field-oriented control (FOC) and other DSP algorithms. The 48-LFQFP package provides 48 gull-wing leads on a 7x7 mm body, suitable for reflow soldering and moderate thermal dissipation. The architecture leverages three parallel execution units (address generation unit, program address generator, and data ALU) within a Harvard-style arrangement, allowing up to six operations per instruction cycle. This parallelism delivers DSP-class throughput while preserving the deterministic interrupt response required for closed-loop control. The device includes dedicated peripherals such as a Flex PWM module, quad timers, and on-chip voltage regulation, simplifying system BOM. Typical applications include three-phase AC induction and BLDC motor control (FOC and trapezoidal commutation), digital power conversion (PFC, solar inverter MPPT, UPS), automotive electronic power steering and body controllers, industrial variable-speed drives, and digital audio processing. The combination of MCU-style peripherals with DSP throughput makes the 56F8300 family a strong fit where closed-loop control and signal processing must coexist on a single chip. When designing with this device, allocate sufficient PCB copper under the exposed pad (where present) to keep junction temperature within the automotive grade range. Use the 56800E code development tools (CodeWarrior, SDK) and verify that the linker configuration matches the on-chip Flash/RAM partitioning shown in the datasheet. For new designs, evaluate the newer MC56F83xxx family successors for active lifecycle. This page synthesizes distributor availability, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers evaluate the MC56F8322MFA60 against active NXP DSC family members and competing solutions.
MC56F8345MFGE - 16-bit DSC 56800E 60MHz 128KB Flash | NXP
The NXP Semiconductors MC56F8345MFGE is a 16-bit digital signal controller (DSC) based on the 56800E core, operating at up to 60 MHz with 128KB (64K x 16) of on-chip Flash program memory, housed in a 128-pin LQFP (14 x 20 mm) package. As part of the 56F834X/56F814X family, it combines the computational throughput of a DSP with the peripheral integration and control flexibility of a microcontroller. A digital signal controller is a hybrid processor class that sits between a general-purpose microcontroller (MCU) and a dedicated digital signal processor (DSP). DSCs such as the 56800E-family parts execute multiply-accumulate (MAC)-intensive DSP algorithms while retaining MCU-style peripherals, interrupt handling, and C-code programmability, making them the natural choice at the top of the embedded control hierarchy for real-time closed-loop systems. Key features of the MC56F8345MFGE include the 16-bit 56800E hybrid core with dual Harvard architecture for parallel instruction and data fetch, 128KB Flash program memory and on-chip RAM, a 12-bit analog-to-digital converter supporting simultaneous motor-control feedback sampling, and multiple pulse-width modulation (PWM) outputs purpose-built for inverter and power-conversion control. Its automotive-relevant temperature grade and gull-wing LQFP terminations support reliable surface-mount assembly. Technically, the 56800E core achieves single-cycle 16 x 16 MAC operations and executes DSP-style bit-manipulation instructions, allowing one controller to run field-oriented motor control loops alongside housekeeping tasks. Program Flash is executable in place, and the peripheral set (PWM, ADC, timers, serial interfaces) is tightly coupled to the core for low-latency control interrupts. Typical applications include three-phase brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) drives, industrial power conversion (inverters, converters, UPS), and digital power supplies where fast deterministic control loops at 60 MHz are essential. When designing with this device, verify availability early: NXP lists this part as NRND (Not Recommended for New Designs), so new projects should evaluate the recommended successor family, and existing designs should secure last-time-buy inventory. This page synthesizes distributor pricing context, drop-in alternatives, and practical design guidance not found in the manufacturer datasheet.
MC56F8347VPY60 - 60MHz 16-bit DSC, 128KB Flash | NXP | 160-LFQFP
The NXP (formerly Freescale) MC56F8347VPY60 is a 16-bit Digital Signal Controller (DSC) combining the peripheral set and ease-of-use of an MCU with the computational power and throughput of a DSP, operating at 60 MHz with 128 KB of on-chip program Flash and 160 pins in an LQFP-160 (LFQFP) industrial-grade package. The MC56F8347VPY60 is built on the 56800E core family and integrates peripherals tuned for digital motor control, power conversion, and embedded signal processing applications, delivering up to 60 MIPS of deterministic throughput for closed-loop control loops. A Digital Signal Controller is a hybrid class of embedded processor that fuses a microcontroller's deterministic interrupt-driven peripheral set with a digital signal processor's single-cycle MAC (multiply-accumulate) engine and parallel data paths. DSCs sit in the hierarchy between general-purpose microcontrollers (which lack DSP throughput) and standalone DSPs (which lack on-chip analog/control peripherals), making them the de-facto choice for digital motor control, switched-mode power supplies, sensor signal conditioning, and high-speed instrumentation. The 56F83xx family specifically targets embedded real-time control where deterministic latency, on-chip ADCs/PWMs, and DSP-grade math are required in a single chip. Key features include a 60 MHz 56800E Harvard-architecture core with single-cycle 16-bit x 16-bit MAC, 128 KB of program Flash, 8 KB of unified data/program RAM, dual 12-bit ADCs with 1.5 us conversion time, a 6-channel PWM module with programmable dead-time insertion, a Quadrature Decoder, multiple serial interfaces (SCI, SPI, I2C), a 4-channel DMA controller, and an external memory interface to LQFP-160 packages with up to 76 general-purpose I/O pins. The 'VPY' package suffix indicates the 160-pin LFQFP industrial-temperature grade (-40C to +105C), and the '60' suffix denotes 60 MHz operation. The 56800E core implements a modified Harvard architecture with three execution units operating in parallel: an Address Generation Unit (AGU), a Data Arithmetic Logic Unit (DALU), and a Program Controller. The single-cycle MAC engine delivers up to 60 MIPS of signal-processing throughput, while the on-chip dual 12-bit ADC samples at up to 1.5 us per conversion enabling precise current/voltage sensing in motor control loops. The on-chip regulator and brown-out detector enhance robustness for industrial environments. Typical applications include AC induction motor vector control, permanent-magnet synchronous motor (PMSM) field-oriented control (FOC), digital PFC power factor correction, uninterruptible power supplies (UPS), solar micro-inverters, three-phase UPS systems, industrial servo drives, and sensor signal processing instrumentation. The dual ADC with simultaneous sampling enables field-oriented control current loops at switching frequencies up to 50 kHz without external ADC support. When designing with this device, carefully plan PCB thermal dissipation: at 60 MHz the core dissipates approximately 0.5 W, and the LFQFP-160 package requires at least 25 cm^2 of 2 oz copper pour for adequate cooling. Designers should also validate toolchain compatibility with CodeWarrior IDE or the Processor Expert tool suite, as the 56800E core requires the legacy 56F8xxx SDK for peripheral drivers and the CW56800 compiler for the C/C++ source. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
MC56F8355MFGE - 16-bit 60MHz DSC 256KB Flash | NXP
The NXP MC56F8355MFGE is a 16-bit digital signal controller (DSC) based on the 56800E core, running at 60 MHz with 256 KB (128K x 16) of on-chip flash program memory, housed in a 128-pin LQFP (14x20 mm) package. A digital signal controller combines the computational architecture of a digital signal processor (DSP) with the peripheral set and control structure of a microcontroller. In the product hierarchy, the MC56F8355MFGE sits within NXP's 56800E core-based DSC family, under digital signal controllers, under hybrid microcontrollers, and under the broader semiconductor/IC category. This hybrid architecture allows a single chip to execute both tight real-time signal-processing loops and general control firmware. Key features include a 16-bit 56800E core at 60 MHz, 256 KB flash, dual 12-bit ADC converters for simultaneous sampling, and integration of CAN, SCI, and SPI serial interfaces with 49 general-purpose I/O lines. The dual ADCs are significant for motor control because phase currents on multiple legs can be sampled at precisely the same instant. Technically, the 56800E core blends Harvard-architecture DSP execution (single-cycle MAC, hardware looping, bit-reversed addressing) with a conventional MCU programming model, supported by the NXP CodeWarrior development environment and the Processor Expert configuration tool. The 56F835X/815X family members share a common peripheral set and documentation, easing migration between memory densities. Typical applications are high-precision motor control (BLDC, PMSM, AC induction with FOC), digital power conversion such as switched-mode power supplies and inverters, and industrial automation nodes requiring deterministic real-time control. Per NXP, the device enables high-precision motor control with 60 MHz performance and dual 12-bit ADCs. Design consideration: the device operates from 2.25 V to 3.6 V over -40 C to +125 C, so 5 V sensor signals need level shifting, and flash retention and Vcap pin requirements documented in the datasheet must be honored. This page synthesizes distributor pricing, family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
MC56F8356MFV60 - 60MHz 16-bit DSC, 144-pin LQFP | NXP
The NXP MC56F8356MFV60 is a 60 MHz 16-bit hybrid Digital Signal Controller (DSC) from the 56F8300 family, integrating the 56800E core with DSP and MCU functionality on a single die, delivered in a 144-pin LQFP package with 1 DSP engine and 256 KB of program Flash. According to the Freescale/NXP 56F8356/56F8156 Technical Data document, the device includes 4 KB unified RAM, 8 KB data Flash, dual 12-bit ADCs, FlexPWMs, FlexCAN, and an external memory interface, enabling migration paths from the 56F8346 with minimal hardware changes. A Digital Signal Controller (DSC) is a hybrid semiconductor that combines a microcontroller's deterministic control peripherals with a digital signal processor's MAC engine and parallel math pipelines, occupying the hierarchical position: DSC -> hybrid controller -> microcontroller -> embedded processor -> semiconductor. Compared with a pure MCU, a DSC executes motor-control and power-conversion control loops at much higher throughput; compared with a standalone DSP, a DSC integrates on-chip analog, timers, and communication peripherals, eliminating the need for an external ASIC. Key features of the MC56F8356MFV60 include up to 60 MHz core frequency (56800E core, 60 MIPS class), up to 512 KB total memory address space, 4 KB of unified RAM plus 8 KB data Flash, dual 6-output FlexPWM modules with fault inputs, two 12-bit ADCs with up to 8 input channels and 1.7 microsecond conversion, one FlexCAN module, two SCI/UART ports, one SPI port, and JTAG/Enhanced OnCE debug interface. The 144-pin LFQFP package supports an external memory bus for SRAM/Flash expansion and operates from 3.0V to 3.6V single supply. Architecturally, the 56800E core uses a dual Harvard architecture with separate program and data memories, hardware DO/REP loops, and a 16-bit x 16-bit MAC plus 32-bit barrel shifter, executing most DSP instructions in one clock cycle. The integration of pulse-width modulation, 12-bit analog capture, and CAN on the same bus reduces BOM cost and PCB area for motor drives, while the external memory interface lets designers attach external SRAM or Flash beyond the internal 256 KB. Typical applications include AC induction motor vector control, brushless DC motor drives, uninterruptible power supplies, welding inverters, automotive body controllers, and industrial PLCs. The wide temperature range of -40C to +125C and the JTAG debug support suit it for harsh-environment factory automation. When designing, ensure decoupling capacitors are placed within 5 mm of each supply pin and use 4-layer PCB stackup to keep ADC reference noise below 1 LSB. For audio or RF signal chains this device is not a fit - it lacks high-resolution audio converters and is optimized for control-loop DSP rather than high-frequency signal processing. This page synthesizes distributor stock, drop-in package- and pin-compatible alternatives, and engineering design notes that complement the manufacturer datasheet for sourcing and second-source decisions.
MC56F8356MFVE - 16-bit 60MHz DSC, 256KB Flash | NXP
The NXP Semiconductors MC56F8356MFVE is a 16-bit digital signal controller (DSC) based on the 56800E core, operating at up to 60 MHz with 256KB (128K x 16) of on-chip flash memory, housed in a 144-pin LQFP (20x20 mm) surface-mount package. A digital signal controller is a hybrid device that combines the computational throughput of a digital signal processor (DSP) with the peripheral integration and control flow of a microcontroller (MCU). Within the power management hierarchy, the 56800E-based 56F8xxx family sits between general-purpose MCUs and dedicated DSPs, offering single-cycle MAC instructions, hardware loops, and bit manipulation suited to real-time closed-loop control such as motor control and power conversion. Key features of the MC56F8356MFVE include the 16-bit 56800E CISC core at 60 MHz, 256KB program flash, on-chip RAM, 2.5V/3.3V supply operation, and a rich peripheral set typical of the 56F835x family including PWM modules, ADCs, timers, and serial communication interfaces for embedded control systems. Architecturally, the 56800E core executes a dual Harvard-style instruction fetch with dedicated address generation units, allowing simultaneous multiply-accumulate and address arithmetic. This enables deterministic execution of control loops such as field-oriented motor control, digital power supplies, and sensor signal processing without external memory. Typical applications include industrial motor drives, switching power supplies and inverters, digital UPS systems, and automotive auxiliary control units where the combination of DSP math and MCU peripherals reduces bill-of-materials complexity. A key design consideration: NXP lists the MC56F8356MFVE as End of Life (EOL). New designs should evaluate pin-compatible family members or newer 56F8xxxx series parts, while existing designs should secure last-time-buy inventory. This page synthesizes distributor availability data, drop-in alternative comparisons, and lifecycle guidance not consolidated in the manufacturer datasheet, per verified data as of 2026-10-18.