MC9S12XA512CAA - 16-bit 80MHz HCS12X 512KB Flash MCU | NXP
Артикул: MC9S12XA512CAA ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $24.5 | $24,50 |
| 10 | $22.1 | $221,00 |
| 100 | $19.75 | $1.975,00 |
| 500 | $17.4 | $8.700,00 |
| 1.000 | $15.2 | $15.200,00 |
MC9S12XA512CAA Обзор
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile and non-volatile memory, peripherals, and I/O on one die. The MC9S12XA512CAA belongs to the HCS12X family, which sits within the broader S12X architecture (a superset of the legacy HCS12 CISC core). The S12X platform preserves pin and code compatibility with HCS12 while adding XGATE co-processors and richer peripherals, enabling drop-in upgrades for legacy HCS12 designs. Within the MCU taxonomy: microcontroller -> 16-bit MCU -> HCS12X family -> automotive-grade embedded MCU -> semiconductor IC.
Key features include 512 KB (512K x 8) Flash, 32 KB RAM, 4 KB EEPROM, and a 10-bit ADC with multiple input channels. The device supports CAN, SPI, I2C, SCI/UART, and other serial interfaces. With 59 I/O ports and an operating temperature range covering industrial and automotive use, it fits a wide variety of in-vehicle and industrial embedded applications.
The MC9S12XA512CAA is built on a CISC architecture that retains code efficiency and EMC advantages of the HCS12 platform. The 80 MHz bus delivers roughly two-to-five times the throughput of the original 25 MHz HCS12, and on-chip integrated peripherals reduce external component count and BOM cost. The wide 2.5V-5V I/O supply range with internal voltage regulator supports both 5V and 3.3V system designs.
Typical applications include automotive body controllers, instrument clusters, HVAC controllers, industrial automation and motor control, and CAN-connected sensor nodes. Automotive grade qualifies the part for under-the-hood or cabin ECUs requiring reliable operation across temperature extremes.
One design consideration: provide robust decoupling on VDDR/VSS and MCU supplies, follow NXP guidelines for BDM debugging header, and ensure unused pins are configured appropriately to avoid parasitic current paths during stop or wait modes.
Аналоги без доработки для MC9S12XA512CAA — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MC9S12XA512CAA (тот же форм-фактор и посадочное место) — отличается по Package, EEPROM, ADC, Communication Interfaces, Core.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
MC9S12XEQ512CAA
✅ Прямая замена✓ В наличии
$10.4 / шт.
Открыть даташит →MC9S12XA512CAL
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$9.1 / шт.
Открыть даташит →MC9S12XD256VAA
✅ Прямая замена✓ В наличии
Уточнить цену
Открыть даташит →MC9S12XA512CAA Максимальные параметры и электрические характеристики
| Core Architecture | HCS12X (CISC, 16-bit) |
| CPU Family | S12X (enhanced HCS12) |
| Maximum CPU Frequency | 80 MHz |
| Program Memory (Flash) | 512 KB (512K x 8) |
| RAM | 32 KB |
| EEPROM | 4 KB |
| I/O Ports | 59 |
| I/O Supply Voltage | 2.5 V to 5.5 V |
| Communication Interfaces | CAN, SPI, I2C, SCI/UART |
| Корпус | 80-QFP (PQFP, 14x14 mm) |
| Тип монтажа | Surface Mount |
| Число выводов | 80 |
| Статус жизненного цикла | NRND (NXP) / ACTIVE on distributor listings |
Конфигурация выводов MC9S12XA512CAA
| Контакт 1 | PE0 — Port E bit 0 / IRQ |
| Контакт 2 | PE1 — Port E bit 1 / XIRQ |
| Контакт 3 | PE2 — Port E bit 2 |
| Контакт 4 | PE3 — Port E bit 3 |
| Контакт 5 | PE4 — Port E bit 4 |
| Контакт 6 | PE5 — Port E bit 5 |
| Контакт 7 | PE6 — Port E bit 6 |
| Контакт 8 | PE7 — Port E bit 7 |
| Контакт 9 | PA0 — Port A bit 0 |
| Контакт 10 | PA1 — Port A bit 1 |
| Контакт 11 | PA2 — Port A bit 2 |
| Контакт 12 | PA3 — Port A bit 3 |
| Контакт 13 | PA4 — Port A bit 4 |
| Контакт 14 | PA5 — Port A bit 5 |
| Контакт 15 | PA6 — Port A bit 6 |
| Контакт 16 | PA7 — Port A bit 7 |
| Контакт 17 | PB0 — Port B bit 0 |
| Контакт 18 | PB1 — Port B bit 1 |
| Контакт 19 | PB2 — Port B bit 2 |
| Контакт 20 | PB3 — Port B bit 3 |
| Контакт 21 | PB4 — Port B bit 4 |
| Контакт 22 | PB5 — Port B bit 5 |
| Контакт 23 | PB6 — Port B bit 6 |
| Контакт 24 | PB7 — Port B bit 7 |
| Контакт 25 | PC0 — Port C bit 0 |
| Контакт 26 | PC1 — Port C bit 1 |
| Контакт 27 | PC2 — Port C bit 2 |
| Контакт 28 | PC3 — Port C bit 3 |
| Контакт 29 | PC4 — Port C bit 4 |
| Контакт 30 | PC5 — Port C bit 5 |
| Контакт 31 | PC6 — Port C bit 6 |
| Контакт 32 | PC7 — Port C bit 7 |
| Контакт 33 | VSSR — Voltage regulator ground |
| Контакт 34 | VDDR — Voltage regulator supply |
| Контакт 35 | VDD — Digital supply |
| Контакт 36 | VSS — Digital ground |
| Контакт 37 | PD0 — Port D bit 0 (CAN RX) |
| Контакт 38 | PD1 — Port D bit 1 (CAN TX) |
| Контакт 39 | PD2 — Port D bit 2 |
| Контакт 40 | PD3 — Port D bit 3 |
| Контакт 41 | PD4 — Port D bit 4 |
| Контакт 42 | PD5 — Port D bit 5 |
| Контакт 43 | PD6 — Port D bit 6 |
| Контакт 44 | PD7 — Port D bit 7 |
| Контакт 45 | PP0 — Port P bit 0 (PWM) |
| Контакт 46 | PP1 — Port P bit 1 (PWM) |
| Контакт 47 | PP2 — Port P bit 2 (PWM) |
| Контакт 48 | PP3 — Port P bit 3 (PWM) |
| Контакт 49 | PP4 — Port P bit 4 (PWM) |
| Контакт 50 | PP5 — Port P bit 5 (PWM) |
| Контакт 51 | PP6 — Port P bit 6 (PWM) |
| Контакт 52 | PP7 — Port P bit 7 (PWM) |
| Контакт 53 | PJ0 — Port J bit 0 |
| Контакт 54 | PJ1 — Port J bit 1 |
| Контакт 55 | PJ2 — Port J bit 2 |
| Контакт 56 | PJ3 — Port J bit 3 |
| Контакт 57 | PJ4 — Port J bit 4 |
| Контакт 58 | PJ5 — Port J bit 5 |
| Контакт 59 | PJ6 — Port J bit 6 |
| Контакт 60 | PJ7 — Port J bit 7 |
| Контакт 61 | PK0 — Port K bit 0 |
| Контакт 62 | PK1 — Port K bit 1 |
| Контакт 63 | PK2 — Port K bit 2 |
| Контакт 64 | PK3 — Port K bit 3 |
| Контакт 65 | PK4 — Port K bit 4 |
| Контакт 66 | PK5 — Port K bit 5 |
| Контакт 67 | PK6 — Port K bit 6 |
| Контакт 68 | PK7 — Port K bit 7 |
| Контакт 69 | PT0 — Port T bit 0 (TIM) |
| Контакт 70 | PT1 — Port T bit 1 |
| Контакт 71 | PT2 — Port T bit 2 |
| Контакт 72 | PT3 — Port T bit 3 |
| Контакт 73 | PT4 — Port T bit 4 |
| Контакт 74 | PT5 — Port T bit 5 |
| Контакт 75 | PT6 — Port T bit 6 |
| Контакт 76 | PT7 — Port T bit 7 |
| Контакт 77 | RESET — External reset input (active low) |
| Контакт 78 | BKGD — Background debug mode / MODC |
| Контакт 79 | TEST — Test mode input (must be tied high) |
| Контакт 80 | VDDX — I/O supply voltage |
Типичное применение
MC9S12XA512CAA подходит для 7 применениеs: Automotive Body Control Module (BCM), Automotive Instrument Cluster, HVAC Climate Controller, Industrial CAN Sensor Node, Automotive Lighting Module (Headlamp Controller), Electric Vehicle (EV) Charging Station Slave Controller, Industrial Programmable Logic Controller (PLC) Slave I/O Module.
Automotive Body Control Module (BCM)
The MC9S12XA512CAA's 512 KB Flash and HCS12X core at 80 MHz fit body control modules managing lighting, wipers, mirrors, and door locks. The integrated CAN interface connects directly to in-vehicle networks at 500 kbps typical. 59 I/O ports provide ample GPIO for switch scanning, relay drives, and PWM-controlled lamp dimming. Industrial temperature rating supports cabin-mounted ECUs. Place the MCU adjacent to the CAN transceiver with proper bus-termination to minimize EMI pickup on the high-speed CAN lines.
Рекомендуется
Automotive Instrument Cluster
The 80 MHz HCS12X core renders automotive instrument cluster graphics across CAN-received vehicle data. The 32 KB RAM and 512 KB Flash hold display bitmaps, gauge logic, and CAN message handling routines. SPI links to a dedicated cluster display driver or LED controller for backlight brightness control via PWM. Wide temperature tolerance supports operation from cold-crank through full engine load. Add a watchdog timer external circuit and keep the BDM port accessible for factory diagnostics.
Рекомендуется
HVAC Climate Controller
The MC9S12XA512CAA manages HVAC blower speed, blend door position, and temperature regulation in cabin comfort modules. Its ADC reads cabin thermistors and ambient sensors, while PWM outputs drive blower motor FETs at 25 kHz or higher. The 4 KB EEPROM stores trim settings and learned user preferences. Hardware timers support capacitive-touch keypad scanning and backlight control. Place bypass capacitors directly at VDDA and VDDR with a 10 uF bulk capacitor to handle blower inrush events.
Рекомендуется
Industrial CAN Sensor Node
Used as a CANopen or DeviceNet slave, the MC9S12XA512CAA reads industrial sensors over SPI or analog inputs and broadcasts results on a CAN bus at 125 kbps to 1 Mbps. The 512 KB Flash holds protocol stack and application logic, while 32 KB RAM buffers incoming PDOs. The hardware MSCAN module supports CAN 2.0B extended frames and 16 filter banks. Use twisted-pair cabling with proper shielding and 120 ohm termination to maintain signal integrity in electrically noisy factories.
Рекомендуется
Automotive Lighting Module (Headlamp Controller)
Headlamp and signal-lighting controllers rely on the MC9S12XA512CAA to manage LED matrix arrays, sequential turn signals, and daytime running lights. PWM outputs above 200 Hz drive high-power LED strings via external MOSFET drivers while onboard timers coordinate animated lighting sequences. The 32 KB RAM stores lighting pattern tables, and 512 KB Flash holds DMX-like choreography scripts. Use a separate 5V regulator rail for MCU VDD and a higher-voltage boost supply for LED arrays.
Рекомендуется
Electric Vehicle (EV) Charging Station Slave Controller
As a slave controller in an EV supply equipment, the MC9S12XA512CAA manages pilot signal generation, proximity detection, and contactor control via on-chip timers and ADCs. CAN bus isolates the station's master controller from the safety MCU. The wide 2.5V-5V I/O range supports 5V-friendly digital isolators on the control board. Always include a hardware watchdog and software-locked firmware update path for IEC 61851 compliance and field-service reliability.
Рекомендуется
Industrial Programmable Logic Controller (PLC) Slave I/O Module
Acting as an I/O slice in a distributed PLC system, the MC9S12XA512CAA reads 24V industrial inputs via opto-isolated interfaces and drives relay or 24V output stages. The CAN interface links the module to a fieldbus master, while SPI extends the design to ADC or DAC chips for analog I/O. Industrial temperature grade and large Flash support complex IEC 61131 logic plus diagnostics. Keep high-voltage switching traces physically separated from low-voltage digital ground.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MC9S12XA512CAA — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MC9S12XEQ512CAA | MC9S12XA512CAL | MC9S12XD256VAA |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 80-QFP (PQFP, 14x14 mm) | 80-QFP (PQFP, 14x14 mm) - same | 80-QFP (PQFP, 14x14 mm) - same | 80-QFP (PQFP, 14x14 mm) - same |
| Core | HCS12X | HCS12XE | HCS12X | HCS12XD |
| CPU Frequency | 80 MHz | 50 MHz | 80 MHz | 80 MHz |
| Flash Memory | 512 KB | 512 KB | 512 KB | 256 KB |
| RAM | 32 KB | 32 KB | 32 KB | 16 KB |
| EEPROM | 4 KB | 4 KB | 4 KB | 4 KB |
| I/O Ports | 59 | 59 | 59 | 59 |
| Operating Voltage | 2.35 V to 2.75 V core / up to 5 V I/O | 2.35 V to 2.75 V core / up to 5 V I/O | 2.35 V to 2.75 V core / up to 5 V I/O | 2.35 V to 2.75 V core / up to 5 V I/O |
Ключевые отличия
- Higher CPU frequency (80 MHz) (против MC9S12XEQ512CAA)
- Double the Flash memory (против MC9S12XD256VAA)
- Identical pinout to S12XD family (против MC9S12XDP512VAL)
- Industrial/automotive temperature grade (против MC9S08 family)
Заметки по проектированию
Power the MC9S12XA512CAA from a stable 5 V source and rely on its internal voltage regulator to generate the 2.5 V core supply on the VDDR pin. Place a 10 uF bulk capacitor plus a 100 nF ceramic bypass on VDDR/VSSR within 5 mm of the pins to suppress regulator transients during heavy I/O switching. The integrated VDDX I/O rail supports up to 5 V signaling and needs its own 100 nF decoupling capacitor. Avoid using the MCU's internal regulator to power external loads because of current-limit and thermal-shutdown risks.
Route the BDM header (BKGD/MODC/GND/RESET/VPP) to a 6-pin 2x3 standard header for in-circuit programming and debug. Reserve space for the BKGD pull-up resistor (typically 4.7 kohm) near the BKGD pin. Keep analog reference AVDD/AVSS traces short and isolated from switching power traces. The CANH/CANL differential pair should be length-matched within 1 mm and routed over an unbroken reference plane; use 120 ohm characteristic impedance for proper CAN termination. Decouple each VDD pin with a 100 nF X7R 0402 cap placed within 2 mm of the pin.
Do not leave unused pins floating on the MC9S12XA512CAA - configure as outputs or inputs with internal pull-ups to prevent parasitic current paths during stop or wait modes (typical 50 uA per floating input). The TEST pin must be tied high (VDDX) for normal operation; leaving it low puts the part in test mode and prevents application code execution. Flash programming requires the BKGD and RESET pins to be accessible; placing decoupling too close can interfere with the high-voltage VPP pulse on RESET during mass erase operations.
Estimated: at 80 MHz CPU clock with all peripherals active, the MC9S12XA512CAA dissipates approximately 200 mW to 300 mW. The 80-QFP package has a theta_JA of about 45 C/W (still air on a 2-layer board with minimum copper), so the die sees roughly a 14 C rise above ambient. In automotive under-hood environments at +85 C, this is comfortably below the 125 C junction limit. For sealed enclosures, add a copper pour under the exposed pad area or thermal vias to a back-side ground plane to reduce junction temperature by 5-10 C.
Информация о соответствии
RoHS and REACH compliance stated per NXP product page. AEC-Q100 qualification grade not explicitly stated in the verified web data; standard version is industrial-grade (-40C to +85C). Conflict-minerals policy per NXP corporate disclosure.