PIC24EP256MC202-E/SO - 70 MIPS 256KB Flash Motor Control MCU | Microchip
Артикул: PIC24EP256MC202-E/SO ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $4.4 | $4,40 |
| 10 | $3.92 | $39,20 |
| 100 | $3.43 | $343,00 |
| 500 | $3.06 | $1.530,00 |
| 1.000 | $2.74 | $2.740,00 |
PIC24EP256MC202-E/SO Обзор
What is a motor-control MCU? A motor-control microcontroller is a specialized MCU that integrates the high-resolution PWM generators, fast ADC, op-amps, and quadrature encoder interfaces required to drive three-phase BLDC, PMSM, and ACIM motors. It sits at the bottom of the power-electronics control hierarchy: power stage -> gate driver -> motor-control MCU -> sensors -> communication bus. This integration eliminates external analog front-end components, reducing BOM cost and improving noise immunity.
Key features include up to 2 PWM channels with 7.5 ns resolution, dual sample-and-hold 10-bit ADC at 1.1 Msps, two on-chip operational amplifiers for current sensing, and a Quadrature Encoder Interface (QEI). The device supports motor-control PWM, input capture, and output compare with dedicated time bases. A 16-channel DMA engine offloads CPU bandwidth, while peripheral pin select (PPS) remaps digital functions to any I/O.
The architecture pairs a modified Harvard bus with a DSP engine delivering single-cycle 16x16 MAC operations and zero-overhead loop control. With dual-partition Flash supporting live update and an on-chip temperature sensor, the device tolerates -40C to +125C ambient conditions. Memory protection and a configurable interrupt controller make it suitable for IEC 60730 Class B safety-compliant appliances.
Typical applications include field-oriented control (FOC) for PMSM/BLDC, HVAC compressor drivers, e-bike traction controllers, industrial servo drives, drone ESCs, and ceiling-fan inverter boards. On-chip op-amps reduce BOM cost and PCB area.
When designing with this device, derate the high-speed PWM duty to leave at least 50 ns dead time at the maximum 120 MHz system clock. Use the internal op-amp in unity-gain for current-shunt sensing with the dedicated ADC trigger from the PWM module.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping procurement and embedded engineers accelerate the design cycle for cost-sensitive 16-bit motor-control systems.
Аналоги без доработки для PIC24EP256MC202-E/SO — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с PIC24EP256MC202-E/SO (тот же форм-фактор и посадочное место) — отличается по Package, Core Architecture, ADC, Operating Temperature, Program Memory (Flash).
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
PIC24EP256MC202-I/SO
✅ Прямая замена✓ В наличии
$4.55 / шт.
Открыть даташит →PIC24EP256MC202T-E/SO
✅ Прямая замена✓ В наличии
$4.61 / шт.
Открыть даташит →DSPIC33EP256MC202-I/SO
✅ Прямая замена✓ В наличии
$3.48 / шт.
Открыть даташит →PIC24EP256GP202-E/SO
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC24EP128MC202-E/SO
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
PIC24EP256MC202-E/SO Максимальные параметры и электрические характеристики
| Core Architecture | PIC24E (16-bit modified Harvard with DSP) |
| Maximum CPU Speed | 70 MIPS (60 MHz FOSC, with 1:1.16 PLL) |
| Program Memory (Flash) | 256 KB |
| Data Memory (SRAM) | 16 KB |
| Operating Voltage Range | 3.0 V to 3.6 V |
| Корпус | 28-pin SOIC (SO, 7.50 mm body, 1.27 mm pitch) |
| Диапазон рабочих температур | -40 C to +125 C (E = Extended) |
| ADC | 10-bit, up to 1.1 Msps, dual sample-and-hold |
| PWM Channels | High-Speed PWM with 7.5 ns resolution |
| On-Chip Op-Amps | 2 operational amplifiers |
| Quadrature Encoder Interface (QEI) | Yes |
| DMA Channels | 16-channel DMA |
| Communication Interfaces | UART, SPI, I2C, ECAN |
| Peripheral Pin Select (PPS) | Yes |
| Уровень MSL | MSL 3 (168 hours) |
| Статус RoHS | Compliant |
Конфигурация выводов PIC24EP256MC202-E/SO
| Контакт 1 | MCLR — Master Clear (reset) input, active-low |
| Контакт 2 | RP0/AN0 — Remappable I/O / Analog input 0 |
| Контакт 3 | RP1/AN1 — Remappable I/O / Analog input 1 |
| Контакт 4 | RP2/AN2/CMP1A — Remappable I/O / Analog input 2 / Comparator 1 output A |
| Контакт 5 | RP3/AN3 — Remappable I/O / Analog input 3 |
| Контакт 6 | VSS — Ground reference |
| Контакт 7 | VDD — Positive supply voltage (3.0-3.6 V) |
| Контакт 8 | RP4/AN4/QEA — Remappable I/O / Analog input 4 / QEI Phase A input |
| Контакт 9 | RP5/AN5/QEB — Remappable I/O / Analog input 5 / QEI Phase B input |
| Контакт 10 | RP6/AN6/INDX — Remappable I/O / Analog input 6 / QEI Index pulse |
| Контакт 11 | RP7/AN7 — Remappable I/O / Analog input 7 |
| Контакт 12 | RP8/PWM1L — Remappable I/O / PWM 1 Low output |
| Контакт 13 | RP9/PWM1H — Remappable I/O / PWM 1 High output |
| Контакт 14 | OSC1/CLKI/RA2 — Crystal oscillator input or external clock |
| Контакт 15 | OSC2/CLKO/RA3 — Crystal oscillator output |
| Контакт 16 | RP10/PWM2L — Remappable I/O / PWM 2 Low output |
| Контакт 17 | RP11/PWM2H — Remappable I/O / PWM 2 High output |
| Контакт 18 | RP12/PWM3L — Remappable I/O / PWM 3 Low output |
| Контакт 19 | RP13/PWM3H — Remappable I/O / PWM 3 High output |
| Контакт 20 | VDD — Positive supply voltage (3.0-3.6 V) |
| Контакт 21 | VSS — Ground reference |
| Контакт 22 | RP14/OC1 — Remappable I/O / Output Compare 1 |
| Контакт 23 | RP15/OC2 — Remappable I/O / Output Compare 2 |
| Контакт 24 | RP16/INT0 — Remappable I/O / External Interrupt 0 |
| Контакт 25 | RP17/RTCC — Remappable I/O / Real-Time Clock Calendar |
| Контакт 26 | RP18/U1RX — Remappable I/O / UART1 receive |
| Контакт 27 | RP19/U1TX — Remappable I/O / UART1 transmit |
| Контакт 28 | VDD — Positive supply voltage (3.0-3.6 V) |
Типичное применение
PIC24EP256MC202-E/SO подходит для 6 применениеs: BLDC/PMSM Field-Oriented Control (FOC), HVAC Compressor Inverter, E-Bike / E-Scooter Traction Controller, Industrial Servo Drive, Drone Electronic Speed Controller (ESC), Ceiling Fan / Appliance BLDC Motor Drive.
BLDC/PMSM Field-Oriented Control (FOC)
The PIC24EP256MC202-E/SO's 70 MIPS PIC24E core with single-cycle 16x16 MAC executes Park and Clarke transforms for sensorless FOC at 8-16 kHz torque-loop rates, while the dual sample-and-hold 10-bit ADC samples two phase currents simultaneously from the on-chip op-amps - eliminating external current-sense amplifiers. The 7.5 ns high-speed PWM resolution supports 50 kHz switching with 250 ns dead time for 24V/48V PMSM drives. Its 256 KB Flash holds a full FOC state-machine plus speed PI controller with headroom for customer-specific parameter tables. Recommended companion: gate driver MCP8024 for 3-phase MOSFET bridges.
Рекомендуется
HVAC Compressor Inverter
Variable-speed HVAC compressors require sinusoidal torque control to minimize audible noise and maximize efficiency at part-load conditions. The PIC24EP256MC202-E/SO drives the compressor's PMSM via sensorless FOC using its high-speed PWM and integrated op-amps for current sensing, with the 256 KB Flash holding the entire compressor state machine (startup, steady-state, anti-surge, defrost, brownout recovery). The -40 C to +125 C extended temperature grade supports outdoor unit operation, and the ECAN interface links the compressor board to the indoor unit's master controller for demand-response commands.
Рекомендуется
E-Bike / E-Scooter Traction Controller
E-bike traction controllers demand high torque at low RPM, regenerative braking, and battery management - all within a compact, low-cost PCB. The PIC24EP256MC202-E/SO integrates 256 KB of Flash for full torque-vectoring firmware, dual on-chip op-amps for leg-current sensing without external amplifiers, and a QEI module for hub-motor Hall-sensor feedback or aftermarket encoder retrofits. Its 16 KB SRAM accommodates CAN-bus message buffers linking to the BMS, while peripheral pin select (PPS) routes UART and PWM to any GPIO for flexible PCB layout in crowded controller housings.
Рекомендуется
Industrial Servo Drive
Low-voltage (24-48 V) industrial servo drives benefit from the PIC24EP256MC202-E/SO's 70 MIPS performance, hardware QEI for incremental encoder feedback, and 256 KB Flash for cascaded position/velocity/current control loops. The DMA engine offloads ADC-to-memory transfers at 1.1 Msps, freeing CPU bandwidth for trajectory planning and EtherCAT/CANopen communication stacks. The 28-pin SOIC package suits compact integrated servo designs where PCB real estate is at a premium. Temperature grade -40 C to +125 C supports cabinet-free machine-mounting applications.
Рекомендуется
Drone Electronic Speed Controller (ESC)
The PIC24EP256MC202-E/SO is a strong fit for racing and cinematography drone ESCs in the 4-6S LiPo, 20-40 A continuous range. Its 7.5 ns PWM resolution supports 24-48 kHz switching for low-acoustic-noise sinusoidal commutation, while the 70 MIPS core runs fast (8-16 kHz) torque loops essential for stable multi-rotor flight control. On-chip op-amps reduce ESC PCB area and BOM cost - critical for weight-sensitive applications. DSHOT and OneShot protocol support is achievable in firmware thanks to flexible PWM and DMA-driven UART peripherals.
Рекомендуется
Ceiling Fan / Appliance BLDC Motor Drive
Cost-sensitive ceiling fans, range hoods, and bathroom exhaust fans increasingly adopt sinusoidal BLDC drives for energy compliance (e.g., EU Lot 6, China GB 21456-2025). The PIC24EP256MC202-E/SO's on-chip op-amps and high-speed PWM eliminate external analog ICs, while 256 KB of Flash supports both sensorless startup (I/F or BEMF) and steady-state FOC algorithms with built-in self-test routines. The -40 C to +125 C temperature grade tolerates enclosed-fixture ambient temperatures above 60 C, and the 28-pin SOIC package supports compact driver-board designs behind the motor housing.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для PIC24EP256MC202-E/SO — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | PIC24EP256MC202-I/SO | PIC24EP256MC202T-E/SO | dsPIC33EP256MC202-I/SO | PIC24EP256GP202-E/SO | PIC24EP128MC202-E/SO |
|---|---|---|---|---|---|---|
| Package | SOIC-28 (SO) | SOIC-28 (SO) - same | SOIC-28 (SO) - same | SOIC-28 (SO) - same | SOIC-28 (SO) - same | SOIC-28 (SO) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | |
| Core / Architecture | PIC24E (16-bit, 70 MIPS) | PIC24E (16-bit, 70 MIPS) | dsPIC33E (16-bit DSP, 70 MIPS) | PIC24E (16-bit, 70 MIPS) | PIC24E (16-bit, 70 MIPS) | |
| Flash / SRAM | 256 KB / 16 KB | 256 KB / 16 KB | 256 KB / 16 KB | 256 KB / 16 KB | 128 KB / 8 KB | |
| Temperature Grade | E: -40 C to +125 C | I: -40 C to +85 C | I: -40 C to +85 C | E: -40 C to +125 C | E: -40 C to +125 C | |
| High-Speed PWM / Op-Amps / QEI | Yes / Yes / Yes | Yes / Yes / Yes | Yes / Yes / Yes + DSP engine | No / No / No (GP variant) | Yes / Yes / Yes | |
| DSP Engine | No | No | Yes (DSPIC33E superset ISA) | No | No |
Ключевые отличия
- On-chip dual operational amplifiers eliminate external current-sense ICs (против PIC24EP256GP202-E/SO)
- Extended -40 C to +125 C temperature grade vs industrial -40 C to +85 C (против PIC24EP256MC202-I/SO)
- 256 KB Flash with dual-partition live update vs 128 KB single-partition (против PIC24EP128MC202-E/SO)
Заметки по проектированию
Place a 100 nF decoupling capacitor as close as possible to each VDD pin (pins 7, 20, 28) and a 10 uF bulk capacitor near the MCU power pins. The 28-pin SOIC has three VDD pins that must all be connected; leaving any one floating causes internal logic errors. For high-current switching applications, add a ferrite bead between the MCU VDD and the noisy digital 3.3 V rail to isolate ADC reference noise from PWM-induced ground bounce. The PIC24EP256MC202 datasheet section 2.4 provides reference decoupling layouts.
Estimated: at 70 MIPS continuous operation with all peripherals active, the SOIC-28 package dissipates approximately 0.3-0.5 W. Thermal resistance theta_JA is approximately 80 C/W for the SOIC-28 on a 2-layer JEDEC test board, resulting in a 25-40 C junction temperature rise above ambient. For enclosed motor-drive housings above 85 C ambient, derate the CPU clock to 40 MIPS (32 MHz FOSC) or improve PCB copper pour under the exposed die pad region.
Do not apply input voltages above 3.6 V to any I/O pin - the PIC24EP family is NOT 5 V tolerant on digital I/O. Use a level translator (e.g., TXS0108E) when interfacing to 5 V sensors or drivers. When using the on-chip op-amps for current sensing, ensure the common-mode voltage stays within 0-VDD and add a 100 ns RC filter on each input to suppress PWM-induced transients. The PIC24EP256MC202 datasheet section 32 'Op-Amp/Comparator' details the supported configurations.
Информация о соответствии
RoHS compliant per Microchip product page. Lead-free SOIC-28 package with matte-tin plating. Not AEC-Q100 qualified; for automotive under-hood applications consider dsPIC33EP256MC506 which is AEC-Q100 Grade 1. PIC24EP family is REACH compliant per EU declaration.
