Mga Microcontroller

Mga Produkto (20,000+)

MSP430FR5994IZVW - 16MHz 256KB FRAM MCU, NFBGA-87 | TI
MSP430FR5994IZVW

MSP430FR5994IZVW - 16MHz 256KB FRAM MCU, NFBGA-87 | TI

The Texas Instruments MSP430FR5994IZVW is a 16-bit ultra-low-power MSP430 FRAM microcontroller featuring a 16 MHz CPUXV2 RISC core, 256KB of non-volatile FRAM memory, 8KB of SRAM, and an integrated Low-Energy Accelerator (LEA) for digital signal processing, housed in an 87-ball NFBGA (6x6 mm) package. An FRAM (ferroelectric random access memory) microcontroller is a class of mixed-signal MCU that replaces traditional flash program memory with ferroelectric RAM. FRAM offers byte-writable, non-volatile storage with dramatically faster write speeds, near-zero write energy, and essentially unlimited endurance compared to flash, making FRAM MCUs part of the broader power-management-focused, low-power semiconductor hierarchy. The MSP430 family pioneered this category and remains its most widely adopted representative. Key differentiating features of the MSP430FR5994 include the LEA vector coprocessor, which TI states delivers up to 40x the DSP performance of Arm Cortex-M0+ MCUs for functions such as FFT, FIR filtering, and matrix multiplication; hardware AES cryptographic acceleration; a 12-bit SAR ADC; an integrated comparator; a multi-channel DMA controller; and eUSCI serial peripherals supporting UART, SPI, and I2C. Multiple 16-bit timers enable motor control, capture/compare, and PWM applications with very low active and standby power consumption. Architecturally, the device is based on the MSP430 CPUXV2 core with unified FRAM program and data storage, allowing flexible memory partitioning under software control via the Memory Protection Unit (MPU). The LEA offloads block-based DSP math from the CPU, freeing cycles for application logic while operating in low-power modes. Typical applications include battery-powered metering and sensing nodes, industrial sensor front ends requiring FFT-based vibration or acoustic analysis, portable medical monitoring devices, and IoT edge endpoints where ultra-low standby power and long battery life are mandatory. A key design consideration is FRAM write protection: configure the MPU segment boundaries early in development to protect persistent data structures from firmware updates. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Kontak
MSP430FR6989IPZ - 16-bit ULP FRAM MCU 128KB | TI LQFP-100
MSP430FR6989IPZ

MSP430FR6989IPZ - 16-bit ULP FRAM MCU 128KB | TI LQFP-100

The Texas Instruments MSP430FR6989IPZ is a 16-bit ultra-low-power MSP430 FRAM microcontroller with 128KB of embedded FRAM, an extended scan interface (ESI), hardware AES-128 accelerator, and an integrated LCD driver, housed in a 100-pin LQFP (PZ) package. It operates from a 16 MHz MSP430 CPUXV2 core with a 1.8 V to 3.6 V supply and is rated for the -40 C to +85 C industrial temperature range. An FRAM-based microcontroller is a mixed-signal MCU whose non-volatile memory uses Ferroelectric RAM rather than flash. FRAM delivers nearly unlimited write endurance (roughly 100x more than flash), faster unified-memory writes at low energy, and a simpler software model because code and data share one address space. The MSP430 FRAM platform combines this memory with TI's holistic ultra-low-power system architecture, allowing designers to log data or run frequent writes without the wear-budget anxiety associated with flash. In the broader hierarchy, this device is a microcontroller -> embedded MCU -> mixed-signal SoC -> semiconductor. Key specifications include 128 KB of non-volatile FRAM, 2 KB of information FRAM, 16 KB of SRAM, a 12-bit SAR ADC with up to 16 channels, four 16-bit timers, up to 83 GPIO pins, a real-time clock, and a 320-segment LCD driver. The integrated extended scan interface is purpose-built for liquid flow-meter rotary sensing, while the AES-128 hardware accelerator supports encrypted metering and secure connectivity. The MSP430FR6989IPZ leverages TI's MSP430 CPUXV2 architecture with active current of approximately 118 uA/MHz and standby current under 1 uA with RTC retention, enabling multi-year battery life in metering and sensor applications. The unified FRAM memory can be partitioned at runtime between code and data, simplifying field firmware updates and over-the-air data logging. Built-in BSL and JTAG/SBW interfaces simplify in-system programming. Typical applications include water, heat, and gas flow meters with rotary sensing, portable medical and industrial sensor loggers, secure battery-powered IoT endpoints, e-paper / LCD human-machine interfaces, and energy-harvesting wireless sensor nodes where its ultra-low-power modes and FRAM endurance deliver measurable system-level advantages. When designing with this MCU, allocate the FRAM memory between code and data carefully - because writes are nearly instantaneous and unlimited, data-logging applications can reserve large blocks for circular buffers, but be sure to budget enough FRAM for firmware images so that in-field updates remain possible. This page synthesizes distributor pricing, parametric alternatives, and practical design guidance that are not aggregated on any single manufacturer or distributor datasheet page.

RFQ Kontak
MSP430G2210ID - 16MHz MCU, 2KB Flash, 128B SRAM | Texas Instruments (Tape & Reel)
MSP430G2210ID

MSP430G2210ID - 16MHz MCU, 2KB Flash, 128B SRAM | Texas Instruments (Tape & Reel)

The Texas Instruments MSP430G2210ID is a 16-bit mixed-signal microcontroller from the MSP430G2xx Value-Series, operating at up to 16 MHz with 2 KB Flash and 128 B SRAM, housed in an 8-pin SOIC (D) package. It features an integrated low-power comparator, a 16-bit timer, and four general-purpose I/O pins, making it well-suited for ultra-low-cost embedded applications. The device operates from a 1.8 V to 3.6 V supply and supports ultra-low power consumption across five power-saving modes. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O into one package. The MSP430 family specifically uses a 16-bit von Neumann RISC architecture, optimized for ultra-low power operation and mixed-signal applications. Within the broader taxonomy, the MSP430G2xx Value-Series targets cost-sensitive applications that still require the low-power signature of the MSP430 platform, sitting between simple 8-bit MCUs and higher-end ARM Cortex-M0 parts in capability and price. Key features of the MSP430G2210ID include active-mode current of 220 µA at 1 MHz (2.2 V), standby current of 0.5 µA, off-mode RAM retention current of 0.1 µA, and an ultra-fast wake-up from standby mode of less than 1 µs. The integrated brownout detector and on-chip internal oscillator simplify BOM cost by eliminating external clock or voltage supervisor components in cost-sensitive designs. The device is supported by TI's MSP430 LaunchPad ecosystem, free Code Composer Studio IDE, and a broad library of application notes covering ultra-low power design patterns. The MSP430G2210ID uses the MSP430 CPU16 core, which combines a 16-bit RISC instruction set with a 16-bit data path, 16 registers, and a constant generator for maximum code density. Program memory is in-system programmable Flash with 2 KB total (approximately 2K x 8 plus 256 B information memory), and the 128 B RAM supports data and stack operations. The internal digitally-controlled oscillator (DCO) provides the 16 MHz maximum clock without external crystals, and the on-chip comparator can wake the CPU from LPM4 with no external components. Typical applications include battery-powered sensor nodes, smoke detectors, remote controls, smart metering, handheld instruments, toys, and any cost-sensitive embedded system requiring ultra-low standby current. The 8-pin SOIC footprint is friendly for hand-soldering and hobbyist prototyping as well as high-volume SMT manufacturing lines. When designing with this device, ensure the supply voltage stays within 1.8 V to 3.6 V and respect absolute maximum ratings on I/O pins to avoid latch-up. The four GPIO pins are multiplexed with the comparator, timer, and JTAG functions; verify pin allocation against the desired peripheral mix before finalizing the schematic. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers select and source the MSP430G2210ID with full context.

RFQ Kontak
MSP430G2210IDR - 16MHz MCU, 2KB Flash, 128B SRAM | Texas Instruments
MSP430G2210IDR

MSP430G2210IDR - 16MHz MCU, 2KB Flash, 128B SRAM | Texas Instruments

The Texas Instruments MSP430G2210IDR is a 16-bit mixed-signal microcontroller from the MSP430G2xx Value-Series, operating at up to 16 MHz with 2 KB Flash and 128 B SRAM, housed in an 8-pin SOIC (D) package. It features an integrated low-power comparator, a 16-bit timer, and four general-purpose I/O pins, making it well-suited for ultra-low-cost embedded applications. The device operates from a 1.8 V to 3.6 V supply and supports ultra-low power consumption across five power-saving modes. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O into one package. The MSP430 family specifically uses a 16-bit von Neumann RISC architecture, optimized for ultra-low power operation and mixed-signal applications. Within the broader taxonomy, the MSP430G2xx Value-Series targets cost-sensitive applications that still require the low-power signature of the MSP430 platform, sitting between simple 8-bit MCUs and higher-end ARM Cortex-M0 parts in capability and price. Key features of the MSP430G2210IDR include active-mode current of 220 µA at 1 MHz (2.2 V), standby current of 0.5 µA, off-mode RAM retention current of 0.1 µA, and an ultra-fast wake-up from standby mode of less than 1 µs. The integrated brownout detector and on-chip internal oscillator simplify BOM cost by eliminating external clock or voltage supervisor components in cost-sensitive designs. The device is supported by TI's MSP430 LaunchPad ecosystem, free Code Composer Studio IDE, and a broad library of application notes covering ultra-low power design patterns. The MSP430G2210IDR uses the MSP430 CPU16 core, which combines a 16-bit RISC instruction set with a 16-bit data path, 16 registers, and a constant generator for maximum code density. Program memory is in-system programmable Flash with 2 KB total (approximately 2K x 8 plus 256 B information memory), and the 128 B RAM supports data and stack operations. The internal digitally-controlled oscillator (DCO) provides the 16 MHz maximum clock without external crystals, and the on-chip comparator can wake the CPU from LPM4 with no external components. Typical applications include battery-powered sensor nodes, smoke detectors, remote controls, smart metering, handheld instruments, toys, and any cost-sensitive embedded system requiring ultra-low standby current. The 8-pin SOIC footprint is friendly for hand-soldering and hobbyist prototyping as well as high-volume SMT manufacturing lines. When designing with this device, ensure the supply voltage stays within 1.8 V to 3.6 V and respect absolute maximum ratings on I/O pins to avoid latch-up. The four GPIO pins are multiplexed with the comparator, timer, and JTAG functions; verify pin allocation against the desired peripheral mix before finalizing the schematic. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers select and source the MSP430G2210IDR with full context.

RFQ Kontak
MSP430G2230ID - 16MHz Low-Power MCU with 10-Bit ADC
MSP430G2230ID

MSP430G2230ID - 16MHz Low-Power MCU with 10-Bit ADC

The Texas Instruments MSP430G2230ID is a 16 MHz mixed-signal microcontroller with 2 KB of Flash memory, 256 bytes of SRAM, and a 10-bit ADC in an 8-pin SOIC package. Its supply range is 1.8 V to 3.6 V, while integrated SPI, I2C, and timer peripherals support compact sensing, control, and communication designs. A mixed-signal microcontroller combines a digital processor with analog measurement and interface functions on one integrated circuit. The MSP430 family belongs to the embedded microcontroller category within integrated circuits. Its 16-bit RISC architecture, 16-bit registers, and low-power operating modes make it suitable for portable measurement and control systems where energy efficiency, deterministic control, and compact peripheral integration are important. Key features include operation up to 16 MHz, 2 KB of Flash program memory, 256 bytes of SRAM, and a 10-bit analog-to-digital converter. The device also provides SPI and I2C communication interfaces, timer resources, and five power-saving modes. Active-mode current is listed as 220 uA at 1 MHz and 2.2 V, while standby current is 0.5 uA and off-mode current with RAM retention is 0.1 uA. The MSP430G2230ID is designed for low-power embedded control. Its 10-bit ADC allows analog sensor signals to be digitized without a separate converter, while SPI and I2C permit connection to external transducers, memory, or remote sensing nodes. The 256-byte SRAM supports small working data sets, and the 2 KB Flash area accommodates compact firmware for dedicated control tasks. Typical uses include portable environmental measurement, battery-powered instrumentation, low-cost sensor nodes, industrial process monitoring, and compact consumer controls. The 8-pin SOIC package also simplifies assembly where a through-hole-compatible surface-mount footprint is preferable to a very small QFN package. When designing the power supply, verify that each rail remains within 1.8 V to 3.6 V and account for the input-voltage range of every attached peripheral. Place the device close to its decoupling network, preserve a short analog-signal path to the ADC input, and follow the recommended external-circuitry and grounding guidance in the manufacturer datasheet. This product summary combines the manufacturer specifications with engineering-focused guidance for low-power firmware development, analog acquisition, serial connectivity, and PCB implementation. It is intended to help engineers identify whether the MSP430G2230ID provides the required memory, conversion capability, interfaces, package, and operating characteristics for a compact embedded design.

RFQ Kontak
MSP430G2553CY - 16MHz 16KB Flash Mixed-Signal MCU | TI
MSP430G2553CY

MSP430G2553CY - 16MHz 16KB Flash Mixed-Signal MCU | TI

Texas Instruments MSP430G2553CY is a 16-bit mixed-signal microcontroller operating at 16 MHz, with 16 KB of Flash memory and 512 bytes of SRAM. The device combines a comparator, timers, UART, SPI, and I2C interfaces in a 32-pin QFN package. The supplied ordering information identifies this orderable MPN as a die-sale device, so package-specific mechanical details and production procurement terms must be confirmed with TI before assembly. A mixed-signal microcontroller is an embedded semiconductor that combines a programmable digital controller with analog or sensing functions. In the product hierarchy, this MSP430 belongs to the microcontroller, embedded processor, semiconductor, and mixed-signal controller classes. Its 16-bit MSP430 CPU architecture makes it suitable for compact control systems requiring low power, deterministic peripheral access, and several communication interfaces without a separate analog processor. The verified device information identifies a 16 MHz operating speed, 16 KB Flash, 512 B SRAM, one comparator, UART/SPI/I2C connectivity, and timers. DigChip additionally lists 24 I/O ports, a 3.3 V to 3.6 V supply range, and a 0.1 µA off-mode current with RAM retention. These figures position MSP430G2553CY for low-power sensing, control, instrumentation, and communications designs where memory and integrated interfaces are more important than high-speed digital processing. The MSP430G2xx family architecture is oriented toward low-power embedded control. Its integrated comparator supports threshold-based sensing, while UART, SPI, and I2C support connections to sensors, displays, transceivers, and external nonvolatile memory. The timer resources can provide event timing and periodic service functions, but individual timer channels, capture/compare resources, and interrupt assignments must be selected from the MSP430G2x53 datasheet for the exact die. Typical applications include battery-powered sensor nodes, compact industrial monitors, digital thermometers, environmental measurement systems, motor or actuator controllers, and simple serial gateways. For a new PCB, the CY suffix and die-sale status require careful review: developers should not assume that the QFN-32 package information found in generic listings corresponds to the CY deliverable. Board assembly may instead require the documented die-sale process, bonding method, and package outline. Before layout, confirm the exact pin assignment and exposed-pad requirements in the official MSP430G2x53 datasheet and with TI. Program development commonly uses an MSP430-compatible toolchain, but the verified data does not identify a specific IDE version, debugger, or programming adapter. Power, ground, decoupling, reset, boot-strapping, communication, and exposed-pad connections should therefore follow the authoritative device documentation rather than generic QFN assumptions. This page consolidates verified manufacturer and distributor information, separates die-sale ordering facts from generic family specifications, and identifies unresolved package, pricing, pinout, lifecycle, and compliance details instead of guessing. It is intended as an engineering-data starting point for MSP430G2553CY sourcing and design review, not as a substitute for TI's final orderable datasheet and quality documentation.

RFQ Kontak
MSP430G2553IN20 - 16MHz 16KB Flash MCU | Texas Instruments
MSP430G2553IN20

MSP430G2553IN20 - 16MHz 16KB Flash MCU | Texas Instruments

The Texas Instruments MSP430G2553IN20 is a 16 MHz mixed-signal microcontroller with a 16-bit RISC CPU, 16 KB of Flash memory, 512 bytes of SRAM, and integrated analog and serial peripherals in a 20-pin PDIP package. Its operating temperature range is -40°C to 85°C. The device combines five low-power modes with a 10-bit ADC and comparator for portable measurement and embedded control designs. A mixed-signal microcontroller combines a digital processor, analog measurement circuitry, communications interfaces, and timing resources within one device. The MSP430G2553 belongs to the MSP430 family of ultra-low-power microcontrollers and targets applications that require deterministic control, efficient peripheral integration, and low standby consumption. Its architecture supports portable instruments, sensing nodes, data acquisition modules, and small embedded-control systems. Key features include a 16-bit RISC CPU operating at up to 16 MHz, 16 KB of Flash, 512 bytes of SRAM, a 10-bit ADC, an analog comparator, UART, SPI, I²C, and timers. The integrated peripherals reduce external component count and allow compact designs that measure analog inputs while exchanging data with external sensors, displays, or host systems. The manufacturer identifies the device for low-power portable measurement applications. The MSP430 architecture uses 16-bit registers and an interrupt-oriented peripheral model. Its mixed-signal resources support sensor conditioning and threshold comparison without requiring a separate analog processor, while UART, SPI, and I²C interfaces provide paths to external integrated circuits. The 20-pin PDIP package also exposes the device through a conventional through-hole footprint suitable for prototyping, education, and industrial control boards. Typical uses include battery-powered measurement instruments, simple data loggers, environmental sensors, industrial sensing nodes, keypad interfaces, and compact embedded-control products. UART, SPI, or I²C can connect a sensor module or local display, while the ADC and comparator support analog measurement. The MSP430G2553IN20 is also widely used as the target device for MSP430 LaunchPad-style development and educational projects. Designers should verify the exact pin functions and peripheral multiplexing against the manufacturer datasheet before laying out the PCB. Decoupling, grounding, unused-pin handling, clock configuration, and low-power mode sequencing are critical in a compact mixed-signal design. The verified data does not provide a complete pin-level mapping, so pin names and electrical details not explicitly supplied are marked as needed rather than inferred.

RFQ Kontak
MSP430G2553IPW0RQ1 - 16MHz Automotive MCU | Texas Instruments
MSP430G2553IPW0RQ1

MSP430G2553IPW0RQ1 - 16MHz Automotive MCU | Texas Instruments

The Texas Instruments MSP430G2553IPW0RQ1 is an automotive 16-bit mixed-signal microcontroller operating at 16 MHz, with 16 KB of Flash memory, 512 B of SRAM, and a 10-bit ADC. It is supplied in a 20-pin TSSOP (PW) package rated for -40°C to +85°C and integrates UART, SPI, I²C, timer, and comparator peripherals. A mixed-signal microcontroller is a semiconductor device that combines a programmable digital controller with analog measurement or signal-conditioning resources. The MSP430 belongs to the MCU → microcontroller → embedded processor → semiconductor hierarchy and is designed for compact, low-power control systems. Its 16-bit CPU16 architecture, on-chip memory, and communication peripherals allow standalone sensing and control without requiring separate memory, ADC, or serial-interface devices. Key device resources include a 16 MHz maximum clock, 16 KB of Flash program memory, 512 B of SRAM, a 10-bit analog-to-digital converter, and an integrated comparator. The MCU supports UART, SPI, and I²C communication, while timer resources support periodic measurement, timing, and control functions. The -40°C to +85°C operating range and automotive qualification make the Q1 device suitable for demanding vehicle electronic modules. The MSP430G2 family architecture combines compact digital processing with mixed-signal measurement. Flash memory retains programmed firmware across power removal, while SRAM supports working variables and stack operations. The ADC provides an integrated path for analog inputs, and the comparator can support threshold detection or basic signal monitoring. Serial interfaces allow the device to communicate with sensors, transceivers, memories, and external controllers. Typical uses include automotive body and sensing modules, battery-powered instrumentation, condition-monitoring controllers, compact data loggers, and low-power industrial controls. The device is especially appropriate where a small TSSOP footprint, mixed-signal integration, and multiple serial interfaces are more valuable than a high-pin-count application processor. Designers should preserve the power, ground, and decoupling layout recommended by the MSP430G2553-Q1 datasheet and verify unused I/O states in the final design. Because automotive qualification, operating-temperature grade, and ordering suffix affect procurement, replacements should be checked for identical package pinout, 16 MHz operation, memory capacity, ADC resolution, and peripheral configuration before substitution. This product page consolidates the verified manufacturer and distributor information for MSP430G2553IPW0RQ1, including package and memory details, current purchasing data, drop-in replacement guidance, comparison parameters, and practical design considerations.

RFQ Kontak
MSP430G2553IPW20 - 16MHz 16KB MCU | Texas Instruments
MSP430G2553IPW20

MSP430G2553IPW20 - 16MHz 16KB MCU | Texas Instruments

The Texas Instruments MSP430G2553IPW20 is a 16-bit mixed-signal microcontroller operating at up to 16 MHz, with 16 KB of Flash memory, 512 bytes of SRAM, and a 20-pin TSSOP (PW) package. According to the Texas Instruments product page, the device includes comparator, UART, SPI, I2C, and timer resources for compact embedded control designs. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, input/output ports, and peripherals into one device. The MSP430 belongs to the mixed-signal MCU family, combining digital control with analog comparison capability and low-power operating modes. This makes it useful for embedded products that must measure a signal, control peripherals, communicate with external systems, or operate from limited power budgets. The MSP430G2553IPW20 provides 16 KB of Flash for firmware, 512 bytes of SRAM for working data, and a maximum clock frequency of 16 MHz. Its listed peripherals include a comparator, UART, SPI, I2C, and timer. The supplied distributor and manufacturer snippets identify the industrial temperature range as -40 °C to +85 °C and the package as 20-pin TSSOP (PW). The verified source data does not provide the complete pin-level electrical table, so individual pin functions and several operating-current values remain unverified. The MSP430G2553 platform is suited to low-power embedded control, sensor conditioning, communication bridges, and small control nodes. The comparator can support threshold-based analog supervision, while the serial interfaces allow connection to displays, sensors, transceivers, or storage devices. The 16 MHz CPU class is appropriate for event handling, protocol management, and control logic where deterministic behavior is more important than workstation-class processing. When designing a board around this MCU, verify the device pinout and the detailed electrical limits in the manufacturer datasheet before routing power, programming signals, communication interfaces, and analog inputs. Pay particular attention to decoupling, oscillator configuration, unused pins, programming access, and the selected supply voltage. Firmware and peripheral assignments should also be checked against the exact device variant and package. This page combines the verified Texas Instruments product information with distributor references, application guidance, and procurement considerations. It is intended to help engineers identify the correct MSP430G2553IPW20 for low-power embedded systems while clearly separating confirmed specifications from parameters that still require datasheet confirmation.

RFQ Kontak
MSP430G2553IPW20R - 16MHz 16KB MCU | Texas Instruments (Tape & Reel)
MSP430G2553IPW20R

MSP430G2553IPW20R - 16MHz 16KB MCU | Texas Instruments (Tape & Reel)

The Texas Instruments MSP430G2553IPW20R is a 16-bit mixed-signal microcontroller operating at up to 16 MHz, with 16 KB of Flash memory, 512 bytes of SRAM, and a 20-pin TSSOP (PW) package. According to the Texas Instruments product page, the device includes comparator, UART, SPI, I2C, and timer resources for compact embedded control designs. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, input/output ports, and peripherals into one device. The MSP430 belongs to the mixed-signal MCU family, combining digital control with analog comparison capability and low-power operating modes. This makes it useful for embedded products that must measure a signal, control peripherals, communicate with external systems, or operate from limited power budgets. The MSP430G2553IPW20R provides 16 KB of Flash for firmware, 512 bytes of SRAM for working data, and a maximum clock frequency of 16 MHz. Its listed peripherals include a comparator, UART, SPI, I2C, and timer. The supplied distributor and manufacturer snippets identify the industrial temperature range as -40 °C to +85 °C and the package as 20-pin TSSOP (PW). The verified source data does not provide the complete pin-level electrical table, so individual pin functions and several operating-current values remain unverified. The MSP430G2553 platform is suited to low-power embedded control, sensor conditioning, communication bridges, and small control nodes. The comparator can support threshold-based analog supervision, while the serial interfaces allow connection to displays, sensors, transceivers, or storage devices. The 16 MHz CPU class is appropriate for event handling, protocol management, and control logic where deterministic behavior is more important than workstation-class processing. When designing a board around this MCU, verify the device pinout and the detailed electrical limits in the manufacturer datasheet before routing power, programming signals, communication interfaces, and analog inputs. Pay particular attention to decoupling, oscillator configuration, unused pins, programming access, and the selected supply voltage. Firmware and peripheral assignments should also be checked against the exact device variant and package. This page combines the verified Texas Instruments product information with distributor references, application guidance, and procurement considerations. It is intended to help engineers identify the correct MSP430G2553IPW20R for low-power embedded systems while clearly separating confirmed specifications from parameters that still require datasheet confirmation.

RFQ Kontak
MSP430G2553IPW28 - 16MHz 16KB Flash MCU | Texas Instruments (Tape & Reel)
MSP430G2553IPW28

MSP430G2553IPW28 - 16MHz 16KB Flash MCU | Texas Instruments (Tape & Reel)

The Texas Instruments MSP430G2553IPW28 is a 16-bit ultra-low-power mixed-signal microcontroller from the MSP430 Value Line series, featuring a 16MHz CPU, 16KB Flash, 512B SRAM, and a rich set of integrated peripherals. Housed in a 28-pin TSSOP (PW) package, it operates from 1.8V to 3.6V over the industrial temperature range of -40 to +85 C. A microcontroller (MCU) is a compact integrated circuit that governs a specific operation in an embedded system, containing a processor core, memory (Flash and SRAM), and programmable I/O peripherals. The MSP430 family sits within the broader hierarchy of 16-bit RISC microcontrollers under power-management-conscious embedded processing, and is renowned for five low-power modes (LPM0 to LPM4) that reduce current to as low as 0.1 uA in standby mode with RAM retention. Key features include a 10-bit ADC, an analog comparator, two 16-bit timers, and a universal serial communication interface (USCI) supporting UART, SPI, and I2C. The device integrates a temperature sensor, brownout reset, and capacitive-touch-enabled I/O. Its internal DCO is factory-calibrated to 16 MHz with approximately 1% accuracy, often eliminating external crystals. Architecturally, the MSP430G2553 uses a 16-bit RISC CPU with a von-Neumann memory map, enabling efficient code density and rapid wake-up from low-power modes. Firmware can be updated in-system via the two-wire Spy-Bi-Wire interface, simplifying production programming. Typical applications include portable medical devices, wireless sensor nodes, smart meters, remote controls, and battery-powered consumer electronics. The 16KB Flash accommodates substantial application code, while 512B SRAM supports moderate buffering. The integrated comparator and ADC enable direct sensor interfacing, and the multiple communication interfaces allow easy connectivity to radios, displays, and other peripherals. Design tip: place a 0.1 uF capacitor close to DVCC and 1 uF at the power entry; configure unused I/O as outputs to avoid floating-input leakage. This mature, widely available part has extensive community support for both prototyping and production. The MSP430G2553IPW28 is a popular choice for cost-sensitive, power-critical designs where performance and low energy consumption are paramount.

USD $0.72 Kontak
MSP430G2553IPW28R - 16MHz 16KB Flash MCU | Texas Instruments
MSP430G2553IPW28R

MSP430G2553IPW28R - 16MHz 16KB Flash MCU | Texas Instruments

The Texas Instruments MSP430G2553IPW28R is a 16-bit ultra-low-power mixed-signal microcontroller from the MSP430 Value Line series, featuring a 16MHz CPU, 16KB Flash, 512B SRAM, and a rich set of integrated peripherals. Housed in a 28-pin TSSOP (PW) package, it operates from 1.8V to 3.6V over the industrial temperature range of -40 to +85 C. A microcontroller (MCU) is a compact integrated circuit that governs a specific operation in an embedded system, containing a processor core, memory (Flash and SRAM), and programmable I/O peripherals. The MSP430 family sits within the broader hierarchy of 16-bit RISC microcontrollers under power-management-conscious embedded processing, and is renowned for five low-power modes (LPM0 to LPM4) that reduce current to as low as 0.1 uA in standby mode with RAM retention. Key features include a 10-bit ADC, an analog comparator, two 16-bit timers, and a universal serial communication interface (USCI) supporting UART, SPI, and I2C. The device integrates a temperature sensor, brownout reset, and capacitive-touch-enabled I/O. Its internal DCO is factory-calibrated to 16 MHz with approximately 1% accuracy, often eliminating external crystals. Architecturally, the MSP430G2553 uses a 16-bit RISC CPU with a von-Neumann memory map, enabling efficient code density and rapid wake-up from low-power modes. Firmware can be updated in-system via the two-wire Spy-Bi-Wire interface, simplifying production programming. Typical applications include portable medical devices, wireless sensor nodes, smart meters, remote controls, and battery-powered consumer electronics. The 16KB Flash accommodates substantial application code, while 512B SRAM supports moderate buffering. The integrated comparator and ADC enable direct sensor interfacing, and the multiple communication interfaces allow easy connectivity to radios, displays, and other peripherals. Design tip: place a 0.1 uF capacitor close to DVCC and 1 uF at the power entry; configure unused I/O as outputs to avoid floating-input leakage. This mature, widely available part has extensive community support for both prototyping and production. The MSP430G2553IPW28R is a popular choice for cost-sensitive, power-critical designs where performance and low energy consumption are paramount.

RFQ Kontak
MSP430G2553IPW8RQ1 - 16MHz Automotive MCU | Texas Instruments
MSP430G2553IPW8RQ1

MSP430G2553IPW8RQ1 - 16MHz Automotive MCU | Texas Instruments

The Texas Instruments MSP430G2553IPW8RQ1 is an automotive ultra-low-power 16-bit microcontroller with a 16 MHz clock, 16 KB of Flash memory, 512 bytes of SRAM, and a 28-pin TSSOP package. It integrates a 10-bit ADC, comparator, UART, SPI, I2C, and timer peripherals for compact control systems. An ultra-low-power microcontroller is a semiconductor device optimized to minimize energy consumption during active operation and standby. The MSP430 belongs to the embedded-controller hierarchy: microcontroller > mixed-signal MCU > ultra-low-power MCU. Its architecture combines a 16-bit RISC core with integrated analog and serial interfaces, reducing the component count required for embedded measurement, monitoring, and control designs. The verified product information identifies a 16 MHz maximum clock, 16 KB Flash, 512 B SRAM, and 10-bit ADC. These resources suit applications that require periodic sensing, local control, and low-rate serial communication without adopting a higher-power application processor. Integrated UART, SPI, and I2C peripherals support sensor, actuator, display, and external peripheral connectivity while preserving a compact embedded design. The MSP430G2553-Q1 product family targets automotive applications and is available in the specified 28-pin TSSOP configuration. Its MSP430 CPU16 architecture processes the ADC, comparator, timer, and communication resources in a compact package. The family-level information confirms the combination of 16 KB Flash and 512 B SRAM, making it suitable for firmware that coordinates mixed-signal sensing and embedded control rather than computationally intensive workloads. Typical uses include automotive body-control modules, low-duty-cycle sensor nodes, battery-operated instrumentation, industrial condition-monitoring equipment, and compact communication controllers. The integrated serial interfaces allow a design to connect sensors over I2C or SPI, use UART for a local link, and employ the ADC for analog measurements while retaining the modest memory footprint of the MSP430 architecture. Designers should verify the exact pin multiplexing, operating-voltage limits, clock configuration, and automotive qualification requirements in the manufacturer datasheet before layout release. The 28-pin TSSOP footprint also requires adequate spacing between fine-pitch leads, careful decoupling near the supply pins, and programming access consistent with the device configuration. This page consolidates verified manufacturer and distributor information, automotive ordering details, practical application guidance, and honest replacement analysis. It distinguishes confirmed drop-in information from package-code or cross-family parts that cannot be treated as true pin-compatible substitutes.

RFQ Kontak
MSP430G2553IRHB32R - 16MHz, 16KB Mixed-Signal MCU | TI
MSP430G2553IRHB32R

MSP430G2553IRHB32R - 16MHz, 16KB Mixed-Signal MCU | TI

The Texas Instruments MSP430G2553IRHB32R is a 16 MHz mixed-signal microcontroller with 16 KB Flash memory, 512 bytes of SRAM, a 10-bit ADC, an analog comparator, UART, SPI, and I2C in a 32-pin VQFN package. It is intended for low-power embedded systems that require compact digital control alongside limited analog measurement capability. The industrial-temperature ordering option is specified for operation from -40°C to +85°C. An ultra-low-power microcontroller is a semiconductor controller designed to minimize energy consumption while executing control, measurement, and communications tasks. The MSP430 family belongs to the mixed-signal MCU hierarchy, combining a 16-bit RISC core with analog and digital peripherals. MSP430 devices use multiple low-power operating modes, making them especially useful in battery-powered instrumentation, portable sensing, and embedded industrial products. The MSP430G2553 operates at up to 16 MHz and provides 16 KB of Flash for program storage plus 512 bytes of SRAM for working memory. Its integrated 10-bit ADC and comparator support analog front ends, while the universal serial communication interface provides UART, SPI, and I2C connectivity. Up to 24 I/O pins can support capacitive-touch functions according to the manufacturer product information. Power efficiency is central to the device architecture. Verified manufacturer information lists active-mode consumption of 230 μA at 1 MHz and 2.2 V, standby current of 0.5 μA, and off-mode current with RAM retention of 0.1 μA. Five power-saving modes allow firmware to match current consumption to workload, although exact standby time and wake-up behavior should be checked in the datasheet for the selected clock configuration. Typical uses include compact environmental sensors, industrial condition-monitoring nodes, low-power data loggers, capacitive-touch controls, wearable measurement devices, and embedded communications modules. The combination of 16 MHz processing speed, serial-interface flexibility, and small memory makes the MCU suitable for coordinating sensors and communicating results through UART, SPI, or I2C. Designers should account for the limited 512-byte SRAM when planning buffers and must place input and output decoupling close to the supply pins. The exposed-pad VQFN package also requires a properly designed thermal and ground layout. Firmware should use the device's low-power modes and avoid blocking delays when battery life is important. This product data combines manufacturer specifications, distributor availability information, and explicit cross-reference findings. It also distinguishes verified technical parameters from values that still require confirmation, providing a practical basis for schematic design, PCB layout, firmware planning, sourcing, and component selection.

RFQ Kontak
MSP430G2553IRHB32T - 16MHz Mixed-Signal MCU | Texas Instruments
MSP430G2553IRHB32T

MSP430G2553IRHB32T - 16MHz Mixed-Signal MCU | Texas Instruments

The Texas Instruments MSP430G2553IRHB32T is a 16-bit mixed-signal microcontroller with a 16 MHz CPU, 16 KB Flash memory, 512 B SRAM, and a 32-pin VQFN package with an exposed thermal pad. It integrates a 10-bit ADC, analog comparator, 16-bit timers, and UART, SPI, and I2C communication capability in an ultra-low-power design optimized for portable measurement and embedded control systems. A mixed-signal microcontroller combines digital processing and analog measurement functions on one semiconductor device. The MSP430 belongs to the ultra-low-power MCU hierarchy, where a 16-bit RISC core and architecture-specific low-power modes reduce energy consumption in battery-powered or intermittently powered equipment. The G2553 device family provides 16-bit registers and constant generators that support efficient execution of compact embedded control algorithms. Verified device features include a maximum clock speed of 16 MHz, 16 KB of programmable Flash, 512 B of SRAM, a 10-bit analog-to-digital converter, a versatile analog comparator, and communication peripherals supporting UART, SPI, and I2C. Up to 24 I/O pins are described as capacitive-touch capable, enabling compact user interfaces and low-cost sensing arrangements without requiring separate switch devices. The MSP430G2553 is based on the MSP430 CPU16 architecture and combines digital control with analog signal acquisition. Its low-power operating modes make it useful for portable instruments, sensor nodes, energy meters, and embedded products that spend substantial time waiting for measurements or user input. The mixed-signal peripherals reduce the component count of designs that otherwise require separate ADC and communication circuitry. Typical uses include low-power data loggers, industrial sensor interfaces, battery-powered monitoring equipment, simple motor-control systems, and connected measurement instruments. UART, SPI, and I2C support allows the controller to communicate with display controllers, external analog or digital sensors, transceivers, and data-storage components. The 16 MHz processing rate is suitable for responsive sampling, control-loop calculation, and peripheral coordination without adopting a higher-power application processor. Designers should use the exposed-pad land pattern correctly for thermal dissipation and should preserve the device's recommended supply and decoupling arrangement. Because firmware size, interrupt configuration, peripheral mapping, and exposed-pad construction affect interchangeability, an alternative should not be treated as a drop-in replacement unless its complete ordering information and pinout have been verified. The verified 32-VQFN construction makes the RHB package especially relevant to compact, surface-mounted industrial designs. This page consolidates the verified manufacturer and distributor information for MSP430G2553IRHB32T and separates confirmed specifications from parameters that still require datasheet confirmation. It also provides application guidance, procurement context, and a conservative replacement assessment that avoids presenting unrelated MSP430 devices as verified pin-compatible substitutes.

RFQ Kontak
MSP430I2031TPWR - 16MHz Metering AFE MCU 32KB Flash | TI
MSP430I2031TPWR

MSP430I2031TPWR - 16MHz Metering AFE MCU 32KB Flash | TI

The Texas Instruments MSP430I2031TPWR is a 16-bit metering analog front end (AFE) microcontroller with a 16.384 MHz 16-bit RISC CPU, three 24-bit sigma-delta ADCs, 32KB Flash, and 2KB RAM, housed in a 28-pin TSSOP (PW) package rated from -40C to +105C. A metering AFE MCU is a mixed-signal microcontroller that combines an MCU core with high-resolution analog-to-digital conversion on the same die. In the power management hierarchy it sits between generic MCUs and dedicated metrology ASICs, integrating sigma-delta conversion, timing, and computation for energy measurement without external ADCs. The MSP430i20xx family belongs to TI's MSP430 Metrology and Monitoring portfolio. Key features include the 16-bit RISC CPU with a DCO-based clock system generating up to 16.384 MHz, three independent 24-bit sigma-delta (SD24) converters ideal for simultaneous voltage and current sampling in poly-phase metering, two 16-bit timers, and five low-power modes optimized for extended battery life. The integrated flash-based memory supports field firmware updates for metering products. Architecturally, the device pairs the CPU16 core with a power management module (PMM) and a flexible clock subsystem, allowing the sigma-delta ADCs to run concurrently with computation for RMS power, energy accumulation, and tariff processing. The 24-bit ADC resolution supports wide dynamic range current sensing via shunt or CT inputs, reducing external component count and calibration effort. Typical applications include single-phase and poly-phase electricity meters, current-voltage monitoring in industrial equipment, battery-powered measurement instruments, and building automation energy sub-metering, where simultaneous multi-channel sampling and low power consumption are decisive. Design consideration: budget the sigma-delta ADC sampling rate against CPU headroom at 16.384 MHz, and place the analog inputs away from switching noise; the 2KB RAM constrains buffering depth for multi-channel DSP algorithms. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ Kontak
MSP430L092SPW - 4MHz 16-Bit MCU | Texas Instruments
MSP430L092SPW

MSP430L092SPW - 4MHz 16-Bit MCU | Texas Instruments

Texas Instruments MSP430L092SPW is a 4 MHz, 16-bit mixed-signal microcontroller with 2 KB ROM, 2 KB SRAM, an 8-bit ADC, an 8-bit DAC, a comparator, and a timer, packaged in a 14-pin TSSOP (PW). The device combines the MSP430 RISC core with embedded analog conversion and comparison functions in a compact surface-mount package. A mixed-signal microcontroller is an integrated circuit that places programmable digital control with analog measurement or output functions on one device. In the MSP430 product hierarchy, the MSP430L092 belongs to the family of ultra-low-power 16-bit RISC microcontrollers within the broader embedded-control and semiconductor categories. Its combination of digital processing and analog peripherals reduces the component count in compact control systems while keeping software development within the MSP430 ecosystem. The principal operating characteristics include a 4 MHz clock, 2 KB of ROM, 2 KB of SRAM, and 8-bit ADC and DAC resolution. The ADC and DAC support direct acquisition and generation of analog quantities, while the comparator can monitor a voltage against a programmable threshold. A dedicated timer supports periodic timing, elapsed-time measurement, and event-generation tasks, making the MCU suitable for deterministic embedded-control sequences. The MSP430L092 uses 16-bit registers and a reduced-instruction-set architecture designed for efficient control operations. Its small 14-pin TSSOP package is appropriate for space-constrained instruments, sensor nodes, and compact control boards. Because the device combines digital processing with an ADC, DAC, comparator, and timer, peripheral sharing can reduce external circuitry and simplify firmware scheduling when the application does not require simultaneous high-rate conversion. Typical applications include low-power sensor acquisition, compact industrial control modules, battery-operated instruments, programmable signal-generation products, and threshold-based monitoring systems. The 8-bit ADC suits slower measurements where higher-resolution conversion is unnecessary, while the DAC supports controllable analog outputs. The timer provides a deterministic time base for sampling, control-loop updates, or periodic actuator commands. Designers should verify the complete electrical limits and pin assignments in the MSP430L092 manufacturer datasheet before layout or firmware release. Decoupling, analog grounding, and regulator selection should follow the device recommendations. Firmware should also account for the 2 KB ROM and 2 KB SRAM limits by controlling library size and avoiding unbounded buffer allocation. This product page consolidates verified manufacturer and distributor information, organizes the mixed-signal feature set, identifies application fit, and clearly documents pricing and pinout data that were not supplied by the retrieved sources.

RFQ Kontak
MSP430L092SPWR - 4MHz 16-Bit MCU | Texas Instruments (Tape & Reel)
MSP430L092SPWR

MSP430L092SPWR - 4MHz 16-Bit MCU | Texas Instruments (Tape & Reel)

Texas Instruments MSP430L092SPWR is a 4 MHz, 16-bit mixed-signal microcontroller with 2 KB ROM, 2 KB SRAM, an 8-bit ADC, an 8-bit DAC, a comparator, and a timer, packaged in a 14-pin TSSOP (PW). The device combines the MSP430 RISC core with embedded analog conversion and comparison functions in a compact surface-mount package. A mixed-signal microcontroller is an integrated circuit that places programmable digital control with analog measurement or output functions on one device. In the MSP430 product hierarchy, the MSP430L092 belongs to the family of ultra-low-power 16-bit RISC microcontrollers within the broader embedded-control and semiconductor categories. Its combination of digital processing and analog peripherals reduces the component count in compact control systems while keeping software development within the MSP430 ecosystem. The principal operating characteristics include a 4 MHz clock, 2 KB of ROM, 2 KB of SRAM, and 8-bit ADC and DAC resolution. The ADC and DAC support direct acquisition and generation of analog quantities, while the comparator can monitor a voltage against a programmable threshold. A dedicated timer supports periodic timing, elapsed-time measurement, and event-generation tasks, making the MCU suitable for deterministic embedded-control sequences. The MSP430L092 uses 16-bit registers and a reduced-instruction-set architecture designed for efficient control operations. Its small 14-pin TSSOP package is appropriate for space-constrained instruments, sensor nodes, and compact control boards. Because the device combines digital processing with an ADC, DAC, comparator, and timer, peripheral sharing can reduce external circuitry and simplify firmware scheduling when the application does not require simultaneous high-rate conversion. Typical applications include low-power sensor acquisition, compact industrial control modules, battery-operated instruments, programmable signal-generation products, and threshold-based monitoring systems. The 8-bit ADC suits slower measurements where higher-resolution conversion is unnecessary, while the DAC supports controllable analog outputs. The timer provides a deterministic time base for sampling, control-loop updates, or periodic actuator commands. Designers should verify the complete electrical limits and pin assignments in the MSP430L092 manufacturer datasheet before layout or firmware release. Decoupling, analog grounding, and regulator selection should follow the device recommendations. Firmware should also account for the 2 KB ROM and 2 KB SRAM limits by controlling library size and avoiding unbounded buffer allocation. This product page consolidates verified manufacturer and distributor information, organizes the mixed-signal feature set, identifies application fit, and clearly documents pricing and pinout data that were not supplied by the retrieved sources.

RFQ Kontak
MSP430P112IDW - 16-Bit 8MHz Ultra-Low-Power MCU | Texas Instruments
MSP430P112IDW

MSP430P112IDW - 16-Bit 8MHz Ultra-Low-Power MCU | Texas Instruments

The Texas Instruments MSP430P112IDW is an ultra-low-power 16-bit RISC mixed-signal microcontroller with an 8 MHz maximum clock, 4 KB of one-time-programmable flash memory, 256 bytes of RAM, and a 20-pin SOIC package. According to the distributor-verified product data, its low 5.5 V supply range and 200 ns minimum instruction-cycle time suit compact embedded control and battery-powered sensing designs. What is an ultra-low-power mixed-signal microcontroller? It is a semiconductor that combines a low-power digital CPU with resources for interacting with analog signals. In the MSP430 family, the MSP430 core belongs to the broader RISC microcontroller hierarchy and is selected when energy efficiency, fast interrupt handling, and compact embedded control matter more than a large memory map or high peripheral integration. Key verified features include a 16-bit RISC architecture, 4 KB OTP, 256 B RAM, and operation up to 8 MHz. The available datasheet search data also identifies a maximum supply voltage of 5.5 V, standby wake-up within 6 microseconds, and off-mode RAM-retention current as low as 0.1 microampere. These figures make the device applicable where the controller spends substantial time waiting for an event and must resume quickly. The MSP430 architecture provides a compact instruction set and deterministic timing useful for embedded measurement, control, and low-duty-cycle monitoring. Its 4 KB program memory is modest, so firmware must be sized carefully, while 256 B of RAM supports local variables and short data buffers. The 20-SOIC format also simplifies assembly and inspection compared with very small packages, although it is larger than modern QFN options. Typical uses include battery-operated sensor nodes, simple industrial controls, compact instrumentation, meter-reading products, and portable measurement devices. Because the supplied data does not enumerate the target device's individual I/O assignments or peripheral set, the complete pinout and peripheral requirements should be checked in the manufacturer datasheet before PCB release. The principal design consideration is supply and power management. Designers should use a regulated supply within the 5.5 V maximum, confirm clock requirements against the selected operating mode, and avoid treating every SOIC-20 MCU as pin-compatible. Programming, reset, and unused-pin handling must follow the MSP430P112 datasheet exactly. This page consolidates the verified distributor specifications, sourcing context, and design cautions for MSP430P112IDW. It also distinguishes factual data from fields that require confirmation, helping engineers evaluate the MCU without introducing unverified electrical, timing, or compliance claims.

RFQ Kontak
MSP430P315CY - 16-Bit 8MHz 16KB OTP MCU | Texas Instruments
MSP430P315CY

MSP430P315CY - 16-Bit 8MHz 16KB OTP MCU | Texas Instruments

The Texas Instruments MSP430P315CY is a 16-bit mixed-signal microcontroller with an 8 MHz MSP430 CPU16 core, 16 KB of one-time-programmable memory, 512 bytes of RAM, and integrated LCD segment support in a low-power system-on-chip design. Its wide 3.3 V to 5.5 V operating capability and five power-saving modes suit compact instruments, meters, industrial controls, and battery-powered products. A mixed-signal microcontroller combines a digital processor, analog and timing resources, memory, and communication peripherals on one chip. Within the MSP430 family, the device belongs to the mixed-signal MCU hierarchy rather than the flash-memory general-purpose MSP430X line. One-time-programmable memory permits a finished device to be programmed once, which can simplify production control when field updates are unnecessary. The verified source information identifies a 16-bit RISC architecture, 16 KB OTP memory, 512 B RAM, up to 92 LCD segments, and operation at 8 MHz. It also reports low-current operation at 1 MHz and 3 V, five power-saving modes, 1.3 uA standby current, 0.1 uA RAM-retention/off current, and a maximum 6 us wakeup from standby. These figures make the MCU appropriate for designs where most of the time is spent waiting for an input or measurement event. The LCD integration is particularly useful for segment-driven meters because external display multiplexing is reduced. The CPU16 architecture supports efficient control of sensor inputs, timers, and LCD segments while retaining state in low-power modes. Firmware and board design must still confirm the required LCD segment map, pin assignments, timing, and voltage limits before layout release. Typical uses include compact utility meters, temperature controllers, industrial panel instruments, portable monitors, and low-cost embedded sensing systems. For battery-powered products, use the standby and RAM-retention modes only when the application can tolerate the stated 1.3 uA and 0.1 uA conditions, respectively. Wakeup latency also affects whether the MCU can meet a short measurement or response interval. The principal design trade-off is OTP memory: it supports a compact, controlled programming process but cannot be updated like flash. Confirm final code size before programming, reserve pins for the exact display and peripherals, and follow the manufacturer’s absolute maximum and recommended operating conditions. This page combines distributor availability, verified family specifications, application guidance, and replacement considerations beyond a raw catalog entry.

RFQ Kontak
MSP430P315IDL - 16-Bit, 8MHz Mixed-Signal MCU | Texas Instruments
MSP430P315IDL

MSP430P315IDL - 16-Bit, 8MHz Mixed-Signal MCU | Texas Instruments

Texas Instruments MSP430P315IDL is a 16-bit RISC mixed-signal microcontroller operating at up to 8 MHz, with 16 KB of one-time-programmable memory, 512 B of RAM, and a 92-segment LCD driver in a 56-pin SSOP package. Designed around the MSP430 family hierarchy of embedded mixed-signal controllers, the device combines low-power operation with dedicated LCD segment support, making it suitable for compact, display-oriented industrial and instrumentation products. A mixed-signal microcontroller is an embedded controller that integrates digital processing with analog-capable peripherals for sensing, timing, communication, and control. Within the semiconductor hierarchy, the MSP430P315IDL belongs to the MSP430x3xx family of 16-bit RISC microcontrollers and combines a power-management-aware design with LCD-driving resources. This family architecture targets applications that need deterministic control, compact display output, and low standby consumption without the complexity of a larger system. Verified product information identifies a maximum clock frequency of 8 MHz, 16 KB of OTP memory, 512 B of RAM, and support for up to 92 LCD segments. The device operates from low-voltage supply rails, with 3.3 V and 5 V operation identified in the distributor records and a maximum supply voltage of 5.5 V. Its 16-bit RISC architecture supports efficient control workloads while the integrated display capability reduces the need for an external LCD controller in segmented-meter designs. Power-management characteristics include standby current of 1.3 µA and off-mode current with RAM retention of 0.1 µA, as stated in the retrieved technical description. Wake-up from standby is specified at up to 6 µs. These figures make the MSP430P315IDL relevant to battery-operated meters, portable instrumentation, and industrial panel devices where idle-current demand is important. The available operating-current value at 1 MHz and 3 V could not be confirmed from the supplied excerpts. Typical uses include multifunction utility meters, industrial measurement panels, temperature controllers, portable test equipment, and compact display instruments. The 92-segment LCD capability is particularly useful when the user interface consists of numeric digits, status indicators, or a matrix of fixed segments. The device can reduce external display-driver circuitry, provided the selected LCD panel and segment mapping are compatible with its multiplexing and pin assignments. The primary design considerations are power-budget verification, LCD bias and segment mapping, oscillator configuration, firmware timing, and decoupling of the supply pins. Designers should use the manufacturer datasheet for the complete pinout, recommended operating conditions, LCD timing, and electrical limits because the verified excerpts do not provide a complete public pin-assignment table. Industrial-grade marking is reported by the distributor data, but detailed temperature limits are not included in the supplied records. This page consolidates verified distributor specifications, lifecycle-relevant sourcing information, package constraints, and a drop-in replacement assessment for the MSP430P315IDL. It also distinguishes confirmed engineering facts from fields that still require datasheet or quotation confirmation, helping engineers avoid treating uncertain parameters as production-ready data.

RFQ Kontak
MSP430TCH5EPW - 16-Bit Haptics MCU | Texas Instruments
MSP430TCH5EPW

MSP430TCH5EPW - 16-Bit Haptics MCU | Texas Instruments

The Texas Instruments MSP430TCH5EPW is a haptics-enabled mixed-signal 16-bit microcontroller with 16 kB of flash memory, 512 bytes of RAM, an 8-channel 10-bit ADC, and two PWM channels, housed in a 28-pin TSSOP package measuring 4.40 mm in width. A mixed-signal microcontroller combines a low-power digital processor with analog measurement and control functions on one integrated circuit. The MSP430 family belongs to the embedded-controller hierarchy of microcontrollers, embedded processors, and semiconductor devices. It is intended for compact products in which touch sensing, haptic feedback, analog monitoring, and embedded control must operate within a small package and a constrained power budget. The MSP430TCH5EPW is differentiated by its dedicated capacitive-touch and haptics capability. Its 10-bit ADC provides eight analog input channels, while two PWM outputs support timed control functions. The 16-bit processor architecture and 16 kB flash capacity provide space for touch configuration, haptic drive control, system state machines, and application firmware. The 512-byte RAM supports working variables and buffered data without requiring a large external memory device. The 28-pin TSSOP package is suitable for conventional surface-mounted PCB assembly and provides a practical alternative to larger leaded packages when product dimensions are constrained. Signal integrity around touch electrodes, ADC inputs, and haptics-drive outputs requires careful partitioning of sensitive analog paths from switching nodes and high-current drive returns. The manufacturer datasheet should be used for exact pin assignments, recommended external components, electrical limits, and initialization procedures. Typical applications include capacitive-touch control panels, haptic feedback interfaces, industrial control panels, appliance user interfaces, compact sensor-hub products, and embedded human-interface systems. In a touch-control design, the MCU can acquire electrode measurements through its mixed-signal resources, evaluate touch conditions, and generate a controlled haptic response through its PWM-capable output architecture. When designing the PCB, place the MCU decoupling capacitors close to their specified supply pins and keep the analog ground and signal paths compact. Confirm input-voltage, output-current, ADC, and haptics-drive constraints against the device limits before connecting external loads. Firmware should also include startup defaults, electrode calibration, and a defined haptics-drive shutdown state to prevent unintended actuator activation. This product page combines the manufacturer device identity, package information, core mixed-signal specifications, application guidance, engineering notes, and verified sourcing links. It also identifies the distinction between a true pin-compatible replacement and a merely similar MCU so engineers can avoid accepting a footprint-level match without checking peripheral functionality.

RFQ Kontak
MSP430U183IPG - 16-Bit RISC Ultra-Low-Power Mixed-Signal MCU | Texas Instruments
MSP430U183IPG

MSP430U183IPG - 16-Bit RISC Ultra-Low-Power Mixed-Signal MCU | Texas Instruments

The Texas Instruments MSP430U183IPG is a 16-bit RISC mixed-signal microcontroller from the MSP430U1xx family, packaged in an 80-pin TQFP (IPG) surface-mount package. It combines an ultra-low-power CPU core with on-chip analog conversion resources and a 16-bit RISC architecture optimized for battery-operated and energy-harvesting systems. A microcontroller (MCU) is a single integrated circuit containing a processor core, non-volatile program memory, data memory, and peripherals such as analog-to-digital converters, timers, and serial interfaces. The MSP430 family belongs to the broader embedded-processor hierarchy: MCU -> embedded processor -> mixed-signal semiconductor. Devices in this line are engineered around a 16-bit RISC core with a highly regular instruction set, 16-bit register file, and hardware designed for very low standby current, making the family a common choice for metering, sensing, and portable control nodes. Key characteristics of this device include its 16-bit RISC instruction set, mixed-signal analog front end integrated on the same die, and a low-leakage design intended for always-on operation. The MSP430U1xx family targets cost-sensitive, low-power designs where a few milliwatts of active power or microamps of standby current determine whether a product is viable. The part is supplied in a surface-mount TQFP-80 (IPG) package, which supports automated assembly and provides ample I/O for external sensing and actuation. Because the part integrates analog signal acquisition alongside digital control, one device can replace a discrete sensor front end plus a small microcontroller. This reduces board area, lowers total component count, and simplifies firmware by keeping the measurement path on the same silicon as the control logic, which minimizes conversion latency and analog routing issues. Typical applications include battery-powered flow and energy meters, portable gas and air quality monitors, industrial sensor nodes, smart home sensing modules, handheld instrumentation, and low-leakage tamper-detection or security peripherals. When designing with the MSP430U183IPG, budget for bypass capacitors on the supply pins, keep analog inputs away from fast switching traces, and consult the pin-description table in the manufacturer datasheet when assigning PCB tracks and test points. Confirm operating voltage limits and current consumption for your specific clock and duty cycle before committing to a power budget. This page consolidates device characteristics, family-level drop-in alternatives, a parameter-by-parameter comparison table, and practical layout and power-design guidance into a single engineering reference that goes beyond the raw datasheet ordering information.

RFQ Kontak
MSP430U275IPM - 64-LQFP 16-Bit Microcontroller | Texas Instruments
MSP430U275IPM

MSP430U275IPM - 64-LQFP 16-Bit Microcontroller | Texas Instruments

Texas Instruments MSP430U275IPM is a 16-bit microcontroller IC identified by distributor listings as an ASIC for the Dolphin chipset, supplied in a 64-LQFP surface-mount package measuring 10 mm by 10 mm. Its defining orderable features are the MSP430 microcontroller category, 16-bit architecture, ASIC implementation, 64-lead LQFP package, and 10 mm by 10 mm body size. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and I/O into one device. The MSP430 family belongs to the embedded-controller hierarchy: microcontroller, embedded processor, semiconductor, and integrated circuit. It is used where a compact control system must execute firmware, read inputs, operate timing functions, and control external circuitry within a defined board-level design. The verified distributor information identifies MSP430U275IPM as an MSP430 Microcontroller IC and an ASIC for the Dolphin chipset. The same sources consistently identify the package as 64-LQFP (10x10), while DigChip specifies tray packaging. Detailed information such as flash memory, RAM, I/O count, clock speed, operating-temperature range, and detailed peripheral assignments was not present in the supplied excerpts and therefore remains unverified on this page. Because the supplied source refers to the U275 as a Dolphin chipset ASIC rather than providing a conventional general-purpose MCU feature summary, engineers should evaluate the device from the complete manufacturer documentation for the specific embedded design. The 64-LQFP footprint also requires a PCB land pattern and pin assignment matching the exact ordering code; a 64-pin package alone does not prove function-level compatibility with another MSP430 device. Typical design contexts for a 16-bit embedded controller include embedded system control, peripheral control, data acquisition, instrumentation, and compact industrial products. The 10 mm by 10 mm LQFP package provides a moderate-size surface-mount option for multilayer PCBs, while tray packaging is identified by the verified product listings. Exact suitability still depends on the unavailable memory, clock, I/O, and electrical specifications. For new layouts, preserve the manufacturer-specified decoupling, programming interface, clock arrangement, and exposed or routed ground-network requirements from the complete datasheet. Also verify programming, debug, and supply-voltage compatibility before substituting this device into an existing design, especially when replacing a microcontroller with a superficially similar 64-LQFP part. This page combines verified package, classification, packaging, inventory, and pricing information with explicit uncertainty notes, helping engineers separate confirmed data from fields that still require the full MSP430U275IPM datasheet for memory capacity, pinout, electrical limits, and lifecycle confirmation.

RFQ Kontak