Mga Microcontroller

Mga Produkto (20,000+)

P1022NSE2LHB - QorIQ P1 2-Core 1.067GHz Power Arch SoC | NXP
P1022NSE2LHB

P1022NSE2LHB - QorIQ P1 2-Core 1.067GHz Power Arch SoC | NXP

The NXP (formerly Freescale) P1022NSE2LHB is a QorIQ P1-series Power Architecture system-on-chip integrating dual e500v2 processor cores at up to 1.067 GHz, packaged in a 689-ball TEPBGA II (31x31 mm) with an operating range of 0C to 105C. The device is designed for complex application processing in IP networking and advanced media processing, combining high-speed connectivity (Gigabit Ethernet, PCI Express, USB) with on-chip security and ECC-protected DDR2/DDR3 memory controllers. Marked "Rev 2" in the part suffix, this member of the P1022 family balances processing throughput with peripheral integration. A QorIQ communications processor is a multicore Power Architecture SoC built for embedded networking and industrial control, sitting in NXP's product hierarchy between the lower-power QorIQ P1 single/dual-core parts and the higher-end P2/P3/P4 multicore platforms. These devices integrate CPU cores, memory controllers, Ethernet MACs, security engines, and various high-speed serial interfaces into a single package, reducing board area and BOM cost for routers, gateways, and industrial controllers compared with discrete CPU-plus-chipset designs. Key features include dual 32-bit e500v2 cores with integrated L1/L2 caches, hardware-accelerated SEC (security engine) for encryption and IPSec, three Gigabit Ethernet interfaces with IEEE 1588 support, three PCI Express controllers, two USB 2.0 controllers (host + device), an LCD controller for HMI panels, and a 32-bit DDR2/DDR3 memory controller with ECC. The "NSE" suffix indicates the standard 0C to 105C commercial temperature grade; the "2" in the suffix denotes silicon revision 2. Architecturally, the P1022 uses a coherent SMP fabric between the two cores, supports hardware virtualization through the embedded hypervisor extensions, and integrates a SerDes block that multiplexes PCIe, SGMII, and SATA lanes. Process technology is 45 nm CMOS, contributing to the 3.5 W to 5 W typical power envelope at full load. The integrated SEC engine accelerates AES, DES, 3DES, SHA, MD5, and Kasumi at line rate, eliminating the need for an external crypto coprocessor on most designs. Typical applications include industrial routers and gateways, factory-automation controllers, networked HMI panels with the integrated LCD controller, secure VPN concentrators leveraging SEC, networked printers and multifunction devices, and small-form-factor NAS/SAN appliances. Engineers commonly pair the P1022 with NXP power management ICs, a DDR3 memory down configuration, and a Vitesse/Marvell Ethernet PHY for SGMII links. When designing with this part, allocate careful attention to PCB layout for the 689-ball BGA: trace length matching on DDR3, SerDes, and PCIe lanes is critical, and a minimum 8-layer stackup with continuous ground planes is recommended. The 0C to 105C operating range and 3.5-5 W dissipation generally permit a moderate copper heatsink or thermal pad, but sealed enclosures should be thermally validated. For new designs, engineers should evaluate the recommended replacement per NXP's PCN/end-of-life notice, as the P1022 family has been superseded by Layerscape LS1021A and LS1028A platforms with equivalent software compatibility. This page synthesizes distributor pricing, BGA pinout, same-family drop-in alternatives, and practical layout guidance not consolidated in the original manufacturer datasheet.

RFQ Kontak
P1022NSE2MHB - QorIQ P1 Dual-Core 1.2GHz SoC | NXP | 689-TEPBGA
P1022NSE2MHB

P1022NSE2MHB - QorIQ P1 Dual-Core 1.2GHz SoC | NXP | 689-TEPBGA

The NXP (formerly Freescale) P1022NSE2MHB is a QorIQ P1 communications processor integrating dual Power Architecture e500v2 cores running up to 1.055GHz (rev 2 silicon, often listed as the 1.2GHz grade by re-marked distributors) in a 689-TEPBGA II (31x31 mm) package. The SoC combines application processing performance with high-speed interconnect peripherals for IP networking, industrial control, and advanced media processing applications. A microprocessor (MPU) is a single-chip CPU that integrates core processing units, memory controllers, and peripheral interfaces into one device, forming the central compute element of an embedded system. Within the broader taxonomy, the P1022 belongs to communications processors (a sub-category of microprocessors), which sit between general-purpose application processors and DSP-heavy media processors, and falls under NXP's QorIQ P1 series of Power Architecture SoCs. Key features include dual 32-bit e500v2 cores with integrated SEC (security engine), hardware ECC support for DDR2/DDR3 memory, a triple-speed Ethernet MAC (GbE), PCIe, USB, and an LCD controller. The device targets low-power embedded applications with operating temperature support from 0C to 105C and a TEPBGA II package that provides excellent thermal dissipation via an exposed die pad. The architecture is built on a 45 nm CMOS process, with the e500v2 cores featuring dual-issue pipelines, hardware MMU, and a coherent SMP fabric. Integrated peripherals are routed through NXP's Coherent Fabric interconnect, enabling deterministic low-latency DMA between Ethernet, PCIe, and memory subsystems - critical for line-rate packet processing. Typical applications include industrial networking routers and switches, smart-grid substation gateways, factory automation controllers, single-board computers for edge computing, and embedded media processing nodes. The integrated SEC engine and GbE switch fabric make it suitable for secure VPN terminators and protocol-converters in industrial environments. When designing with this part, engineers must respect the 689-ball BGA routing complexity, providing at least 6 PCB layers with controlled impedance for DDR3 traces and length-matched Ethernet pairs. The exposed die pad requires thermal vias to inner copper planes for proper heat extraction under sustained load. Firmware should enable SEC early in boot for secure boot chain verification. This page synthesizes distributor pricing, NXP cross-reference data, and practical board-design notes not found in the manufacturer datasheet alone, enabling rapid sourcing and design-in decisions.

RFQ Kontak
P1022NSN2E$B - QorIQ P1 600MHz Dual-Core MPU | NXP | BGA-689
P1022NSN2E$B

P1022NSN2E$B - QorIQ P1 600MHz Dual-Core MPU | NXP | BGA-689

The NXP Semiconductors (formerly Freescale) P1022NSN2E$B is a QorIQ P1 series integrated communications processor built around dual PowerPC e500v2 cores operating at up to 600 MHz, housed in a 689-ball TEPBGAII (31x31 mm) package. The device targets embedded networking, industrial control, and secure printing applications where deterministic packet processing and hardware-assisted cryptography are needed. A communications processor (often abbreviated MPU or networking SoC) is a system-on-chip that integrates one or more CPU cores with Ethernet MACs, security accelerators, DDR memory controllers, PCIe interfaces, and other peripheral logic on a single die. The P1022NSN2E$B sits in the taxonomy: MPU -> communications processor -> embedded processor -> SoC -> semiconductor. It belongs to NXP's QorIQ P1 family, which sits below the higher-tier QorIQ P2/P3 and above the entry-level QorIQ P0 lines. Key features include dual 32-bit e500v2 cores with superscalar out-of-order execution, integrated SEC 4.0 cryptography engine, two 10/100/1000 Mbps Ethernet MACs (RGMII/SGMII support), a DDR2/DDR3 memory controller with ECC, two PCIe Gen2 controllers, four UARTs, two I2C, and SD/MMC support. The device operates from a typical 1.0 V core supply and 3.3 V I/O supply with industrial-grade -40 °C to +105 °C junction temperature range. The 31x31 mm TEPBGAII exposed-pad package provides a low-inductance thermal path for high-performance embedded workloads. The P1022NSN2E$B applies a 45 nm process technology and integrates the datapath, queue manager, and buffer manager engines used in earlier PowerQUICC III parts, but consolidates them with dual cores for higher aggregate throughput per watt. The platform is supported by NXP's Software Development Kit for QorIQ and the U-Boot firmware tree, allowing engineers to bring up Linux, VxWorks, or proprietary RTOS builds quickly. Typical applications include industrial Ethernet switches and routers, secure print server controllers, factory automation gateways, multi-protocol industrial networking, and embedded security appliances. The integrated SEC 4.0 engine accelerates IPsec, TLS/SSL, and bulk cipher primitives, making it well suited for VPN termination and secure edge gateways. When designing with this device, allocate generous PCB area for the 31x31 mm BGA, use matched-length routing for the DDR2/DDR3 byte lanes, and follow NXP's reference design's decoupling and via-in-pad thermal pad pattern. The legacy 600 MHz speed grade is now considered mature; designers targeting new designs at higher throughput should compare against the P1024/P2020 family members. This page synthesizes distributor inventory, current pricing, verified parametric values, and drop-in alternatives for the P1022NSN2E$B - information not aggregated in a single datasheet viewing.

RFQ Kontak
P1022NSN2EFB - QorIQ Dual-Core e500v2 MPU 1.055GHz | NXP
P1022NSN2EFB

P1022NSN2EFB - QorIQ Dual-Core e500v2 MPU 1.055GHz | NXP

The NXP P1022NSN2EFB is a dual-core PowerPC e500v2 microprocessor from the QorIQ P1 communications platform family, operating at up to 1.055 GHz and housed in a 689-pin TEPBGA II (31x31 mm) package. It integrates two 32-bit Power Architecture e500v2 cores with advanced system peripherals, a DDR2/DDR3 memory controller with ECC, dual Gigabit Ethernet controllers, multiple PCIe lanes, USB 2.0, and an LCD controller, making it a system-on-chip (SoC) for IP networking and industrial embedded applications. A microprocessor is an integrated circuit that fetches, decodes, and executes instructions of a stored program; in embedded systems it typically combines one or more CPU cores with on-chip peripherals to form a complete application processor or SoC. The QorIQ P1 series from NXP sits in the hierarchy: embedded MPU -> communications processor -> Power Architecture SoC -> QorIQ platform -> NXP networking portfolio, succeeding the legacy PowerQUICC III family and targeting mid-range routers, switches, and industrial control. Key features include 1.055 GHz core frequency, dual e500v2 cores with MMU and double-precision FPU, hardware ECC for DDR2/DDR3 memory, integrated SEC (security engine), four 10/100/1000 Ethernet MACs, two PCIe controllers, USB 2.0 host/device, SD/MMC, SPI, I2C, UART, and an LCD controller supporting up to 1280x1024 resolution. Industrial temperature range is 0C to 105C per the trailing "EFB" speed-grade code, and the device operates from 1.5V/1.8V/2.5V/3.3V supplies. The architecture combines out-of-order dual-issue cores with the DPAA-style peripheral set and a high-bandwidth interconnect that sustains multi-Gbps packet throughput while running control-plane software. The hardware security block accelerates IPsec, SSL/TLS, and bulk crypto, offloading the cores for data-plane tasks. Typical applications include industrial Ethernet routers, fanless industrial gateways, smart-grid concentrators, factory-automation controllers, networked printers, defense radios, and embedded vision systems. Drop-in deployment is enabled because the device ships in the only 689-pin TEPBGA package used across the P1022/P1013 family, allowing PCB reuse when moving between speed grades and core counts. When designing with this MPU, pay close attention to DDR3 trace length matching, the SEC engine firmware dependencies, and the thermal envelope: at full 1.055 GHz dual-core load with 1.5V core, the device can dissipate several watts, so a 4-layer minimum PCB with a ground flood under the BGA is required. This page consolidates distributor pricing, same-package drop-in alternatives across the QorIQ P1 family (P1013 single-core variant and P1022 speed grades), and application-level guidance not found in the standalone manufacturer datasheet.

RFQ Kontak
P1022NSN2HFB - QorIQ 32-Bit Power Arch SoC 800MHz 2-Core | NXP
P1022NSN2HFB

P1022NSN2HFB - QorIQ 32-Bit Power Arch SoC 800MHz 2-Core | NXP

The NXP P1022NSN2HFB is a QorIQ P1022 family 32-bit Power Architecture system-on-chip (SoC) featuring dual e500 processor cores running up to 800 MHz core / 400 MHz platform / 667 MHz DDR, integrated in a 689-pin PBGA exposed-pad package. The P1022NSN2HFB variant targets networking and industrial applications with an operating temperature range of 0 C to 105 C, Revision 2 silicon, and is offered as an industrial-grade part with lead-free (Pb-free) packaging. A QorIQ SoC is a system-on-chip that integrates one or more Power Architecture CPU cores, memory controllers, high-speed interconnect fabrics, and peripheral IP blocks onto a single die. QorIQ platforms sit within the broader NXP processor taxonomy: SoC -> communications processor -> embedded microprocessor -> Power Architecture device -> semiconductor. The QorIQ P1 family is positioned for cost-sensitive multi-core networking and industrial control workloads where integration reduces BOM and PCB complexity. Key features of the P1022 include dual e500 cores with double-precision floating-point support, an integrated DDR2/DDR3 memory controller with ECC, three Gigabit Ethernet controllers (one 10/100/1000 plus two RGMII), two PCI Express controllers (x1/x2), a USB 2.0 controller (host/device), an LCD controller, secure boot, and Trust Architecture features. The device is fabricated in a 45 nm CMOS process, and the PBGA-689 exposed-pad package provides a low thermal resistance path for sustained compute workloads. Architecturally, the P1022 implements a hierarchical interconnect with coherent L1 caches per core and a shared L2 cache. The CoreNet platform coherently fabric fabric is shared with the DDR memory controller. Hardware accelerators for cryptography and pattern matching (SEC 4.0 engine) are integrated for line-rate security processing. This combination delivers wire-speed networking throughput while freeing CPU cores for application and control-plane tasks. Typical applications for the P1022NSN2HFB include IP networking equipment such as branch-office routers, Ethernet switches, industrial gateways, and network-attached storage (NAS). The integrated LCD controller and DDR3/2 controller also make it suitable for human-machine interface (HMI) controllers, building automation, and factory-floor protocol bridges where deterministic Power Architecture performance is required. When designing with this device, engineers should pay close attention to power-rail sequencing and the exposed-pad thermal management. The 689-ball PBGA requires a properly stitched thermal via array beneath the exposed pad to dissipate the full-chip power; a four-layer PCB with 2 oz copper on outer layers is typically the minimum recommended stack-up. This page synthesizes distributor availability, datasheet pinout details, same-family drop-in alternatives, and lifecycle status not consolidated in the manufacturer part page alone, giving procurement and design engineers a single decision-ready reference for the P1022NSN2HFB.

RFQ Kontak
P1022NSN2LFB - QorIQ P1 1.055GHz Dual-Core PowerPC SoC | NXP
P1022NSN2LFB

P1022NSN2LFB - QorIQ P1 1.055GHz Dual-Core PowerPC SoC | NXP

The NXP P1022NSN2LFB is a dual-core QorIQ P1 communications processor built on Power Architecture e500v2 cores running at up to 1.055 GHz, integrated in a 689-ball TEPBGA II (31x31 mm) package. It combines two 32-bit e500v2 cores with high-speed connectivity peripherals including dual Gigabit Ethernet, PCI Express, USB, DDR2/DDR3 with ECC, and an LCD controller for industrial HMI. A QorIQ communications processor is a system-on-chip (SoC) that integrates one or more Power Architecture CPU cores with networking and media peripherals on a single die. QorIQ P1 sits within the broader NXP PowerQUICC and QorIQ family hierarchy: PowerQUICC III -> QorIQ P1/P2/P3/P4/P5 -> communications processors -> microprocessors -> integrated circuits. This taxonomy places the P1022 in the entry-to-mid-tier networking and industrial processing segment. Key features include a 32 KB instruction and 32 KB data L1 cache per core, 256 KB shared L2 cache with ECC, dual 10/100/1000 Mbps Enhanced Three-Speed Ethernet (eTSEC) controllers, two PCI Express endpoints/RCs, USB 2.0 with PHY, an integrated LCD controller supporting up to WXGA resolutions, and a DDR2/DDR3 memory controller with ECC support. The device targets an operating temperature range of 0 to 105 °C (commercial/industrial grade). The P1022 integrates hardware acceleration for security (SEC 3.3 engine with DES, 3DES, AES, SHA, RSA, Kasumi) and four DMA controllers for offloading data movement. The high-speed SerDes block can be configured for SGMII, PCIe, SRIO, or Aurora interfaces, providing flexible front-panel and backplane connectivity. The integrated LCD controller eliminates the need for an external graphics chip in many HMI designs. Typical applications include industrial routers, factory automation gateways, networked HMI panels, smart-grid concentrators, networked printers, and point-of-sale terminals. The dual GbE plus PCIe combination makes it well suited as a control-plane processor for small-cell base stations and industrial Ethernet switches. When designing with the P1022, ensure the DDR2/DDR3 interface is routed with 50 ohm controlled impedance and matched length within the byte lanes. The TEPBGA II package requires a multilayer PCB with stitched ground vias under the BGA field for power integrity and thermal dissipation. Firmware should leverage U-Boot or the NXP SDK for proper Secure Boot fuse configuration. This page synthesizes distributor pricing, drop-in alternatives from the QorIQ P1 family, and practical board-layout guidance not found in the manufacturer datasheet alone.

RFQ Kontak
P1022NSN2MHB - QorIQ P1 Dual-Core SoC, 1.055GHz | NXP
P1022NSN2MHB

P1022NSN2MHB - QorIQ P1 Dual-Core SoC, 1.055GHz | NXP

The NXP P1022NSN2MHB is a dual-core Power Architecture (e500v2) QorIQ P1 system-on-chip (SoC) microprocessor running at 1.055 GHz core frequency, housed in a 689-ball TEPBGA II (31 x 31 mm) package. The device integrates dual 32-bit PowerPC e500v2 cores with 36-bit physical addressing, a high-speed interconnect fabric, and a rich peripheral set that includes GbE, PCIe, USB, DDR2/DDR3 with ECC, LCD controller, security engine, and SATA. According to the manufacturer part description, the P1022 family is designed to deliver complex application processing performance with exceptional feature integration and high-speed connectivity for IP networking and advanced media processing. A QorIQ SoC belongs to the power-architecture communications processor family - an integrated multiprocessor IC that combines CPU cores, memory controllers, and networking/connectivity peripherals on a single die. Within the broader taxonomy, QorIQ P1 sits beneath the QorIQ P-series (communications), below the QorIQ platform tier, and ultimately under the Power Architecture / embedded microprocessor category. The P1 tier targets cost- and power-sensitive networking and industrial applications where a single-chip SoC replaces a CPU plus external chipset. Key features of the P1022NSN2MHB include dual 1.055 GHz e500v2 cores with integrated FPU/LSU per core, 32 KB I-cache and 32 KB D-cache per core, a DDR2/DDR3 SDRAM controller with ECC support up to 800 MT/s data rate, three 10/100/1000 Mbps enhanced Gigabit Ethernet controllers (eTSECs), two PCIe interfaces (PCIe x4 + PCIe x1 or x4 + x4 configuration), one USB 2.0 controller with ULPI interface, integrated LCD controller supporting up to 1280 x 1024 resolution, SATA 2.0 interface, SD/MMC host controller, two I2C controllers, four UARTs, enhanced SPI, and a security engine supporting DES/3DES, AES, RSA, and ARC4. Power management is provided through a sophisticated voltage and frequency scaling infrastructure. The operating temperature range spans -40C to +125C, indicating the part targets industrial and extended-temperature applications. Technically, the P1022 implements a hierarchical interconnect with separate CoreNet platform and peripheral bus, enabling concurrent high-bandwidth data movement between cores, memory, and networking engines. This architecture minimizes contention when simultaneously running packet processing, control-plane tasks, and media workloads. ECC on the DDR controller protects against single-bit memory errors critical for network and storage reliability, while the integrated LCD controller eliminates the need for an external graphics chip in HMI applications. Typical applications for this SoC include industrial networking gateways, factory-automation controllers, multi-port Ethernet switches/routers, network-attached storage (NAS) controllers, industrial IoT edge nodes, secure point-of-sale terminals, and embedded HMI panels. The device is also used in smart-grid substation equipment and other long-lifecycle industrial platforms where its -40C to +125C range is mandatory. Designers should budget power carefully: at 1.055 GHz the device draws several watts, and a multilayer PCB with continuous ground planes plus thermal vias under the exposed pad is required. The TEPBGA II package has a large ball count (689), so 4-6 layer PCB with 0.8 mm or finer pitch fanout, microvia-in-pad, and controlled-impedance routing for DDR/PCIe/SerDes traces is mandatory for signal integrity. This page synthesizes NXP part documentation, distributor pricing, and same-family drop-in alternatives - not all of which are aggregated on a single distributor product page.

RFQ Kontak
P1022NXE2HFB - QorIQ P1 SoC 1.055GHz Dual e500v2 689-TEPBGA | NXP
P1022NXE2HFB

P1022NXE2HFB - QorIQ P1 SoC 1.055GHz Dual e500v2 689-TEPBGA | NXP

The NXP P1022NXE2HFB is a QorIQ P1 series communications processor built on Power Architecture technology, integrating two e500v2 cores operating at up to 1.055 GHz in a 689-ball TEPBGA II (31x31 mm) package. The device combines dual PowerPC e500v2 processor cores with the high-speed system interconnect required for IP networking routers, line cards, and advanced media processing gateways, supporting DDR2/DDR3 memory with ECC, three Gigabit Ethernet MACs, PCI Express, USB, LCD, and SEC security offload. A QorIQ communications processor is a multi-core SoC optimized for embedded networking and industrial control workloads where deterministic throughput, hardware-accelerated security, and rich peripheral integration replace discrete ASICs plus an external CPU. It sits at the top of the taxonomy: communications processor -> SoC -> microprocessor -> integrated circuit -> semiconductor, sharing lineage with PowerQUICC predecessors while migrating to a deeper pipeline and on-die peripherals. Key differentiating specifications include dual e500v2 cores with MMU/FPU support, integrated SEC 4.x security engine for IPSec and SSL/TLS offload, three enhanced Gigabit Ethernet MACs with SGMII/RGMII/MII interfaces, DDR2/3 memory controller with ECC up to 800 MT/s, two PCI Express controllers, USB 2.0 with ULPI, and an LCD controller. The integrated security and networking acceleration remove the need for companion crypto and Ethernet PHYs at the data-plane level. The architecture pairs a 32-bit superscalar e500v2 core with a coherent system bus, platform cache, and dedicated DMA engines, allowing deterministic throughput for wire-speed packet processing. The 1V core / 1.0-1.05V I/O operation reduces board-level power complexity versus legacy multi-rail PowerQUICC designs, and the 689-TEPBGA exposed-pad package provides the thermal headroom required for fanless industrial enclosures rated -40C to +125C. Typical applications include industrial networking gateways, factory automation controllers, secure IoT edge routers, line-rate network appliances, HMI panels with LCD, and legacy PowerQUICC migrations. Designers adopt the P1022 family when deterministic dual-core Power Architecture performance with hardware security and multi-protocol I/O is needed on a single SoC. When laying out the board, allocate a continuous ground plane beneath the exposed pad and use at least 8 vias in a 3x3 grid for thermal relief. Respect DDR3 routing rules (length matching within 25 mils for byte lanes) and keep PHY-side differential pairs (SERDES, PCIe) length-matched to within 150 mils of the companion transceiver. This page synthesizes NXP datasheet specs, distributor pricing, and drop-in alternative guidance that is not aggregated in the manufacturer's product brief alone.

RFQ Kontak
P1022NXE2LFB - QorIQ Dual-Core 1GHz SoC | NXP
P1022NXE2LFB

P1022NXE2LFB - QorIQ Dual-Core 1GHz SoC | NXP

The NXP P1022NXE2LFB is a dual-core QorIQ Power Architecture system-on-chip (SoC) that integrates two e500v2 cores running up to 1.055 GHz, packaged in a 689-ball TEPBGA II (31 x 31 mm) for high-performance industrial and networking applications. According to the NXP product page, this device combines dual Power Architecture cores with on-chip peripherals including two Gigabit Ethernet controllers, PCI Express, USB 2.0, DDR2/DDR3 memory controller with ECC, and a security engine, targeting IP networking, industrial gateways, and advanced media processing workloads. A QorIQ P1022 SoC is a members of NXP's Power Architecture-based communications processor family, positioned between the single-core P101x and higher-core P20xx platforms. QorIQ processors historically delivered integrated networking, security, and packet-processing acceleration within a single chip, reducing bill-of-materials compared with discrete CPU-plus-assist-chip designs for router, switch, and industrial control use cases. The P1022 family specifically addresses mid-range dual-core workloads needing deterministic performance with low power envelope. Key features of the P1022NXE2LFB include dual 32-bit e500v2 cores up to 1.055 GHz, integrated 32 KB I-cache and 32 KB D-cache per core, DDR2/DDR3 memory controller with ECC support up to 800 MHz data rate, two 10/100/1000 Mbps Ethernet MACs, three PCI Express controllers, two USB 2.0 controllers (host + device), an LCD controller, and an integrated security engine supporting DES, 3DES, AES, and public-key acceleration. The 'E' industrial-temperature range from -40C to +125C, together with the 'L' lithography and 'FB' lead-free ball package, makes the device suitable for harsh-environment embedded systems. Architecturally, the P1022NXE2LFB leverages the Power Architecture e500v2 superscalar core with out-of-order execution, a coherent CoreNet fabric interconnect, and dedicated datapath engines for packet parsing, queue management, and cryptography. The SoC integrates multiple power islands so that unused blocks can be clock-gated, allowing systems designers to hold platform power below target thermal envelopes even with the dual cores active. Typical applications for the P1022NXE2LFB include industrial Ethernet gateways, programmable logic controllers with protocol conversion, secure network-attached storage controllers, factory-floor edge routers, building automation controllers, and embedded industrial PCs running Linux or VxWorks. The dual-core configuration supports real-time control cores combined with networked application cores within a single SoC footprint. When designing with the P1022NXE2LFB, consider that the device is approaching end-of-life per NXP's product discontinuance notice shown on the official product page. Designers of long-lifecycle programs should evaluate the NXP P1022 successor, or migrate to the LS1021A family, both of which pin-redefine rather than drop-in, so a layout revision is unavoidable. The 689-ball TEPBGA requires careful PCB stackup and microvia technology to escape the fine 1 mm pitch BGA. This page synthesizes current distributor availability, lifecycle status, and parametric positioning of the P1022NXE2LFB relative to its same-family and same-package alternatives, information not consolidated in a single source from the manufacturer datasheet alone.

RFQ Kontak
P1022NXN2HFB - QorIQ P1 Dual-Core e500v2 SoC | NXP
P1022NXN2HFB

P1022NXN2HFB - QorIQ P1 Dual-Core e500v2 SoC | NXP

The NXP P1022NXN2HFB is a QorIQ P1 series dual-core Power Architecture system-on-chip (SoC) integrating two e500v2 cores running up to 1.055 GHz, packaged in a 689-ball TEPBGA II (31x31 mm) form factor. It combines a 32-bit RISC/MPU subsystem with high-speed connectivity peripherals and is characterized for an extended industrial temperature range of -40C to +125C. A microprocessor (MPU) is an integrated processing subsystem that executes software instruction streams and orchestrates system peripherals. The QorIQ P1 tier sits within NXP's Power Architecture-based communications processor family, targeting IP networking, industrial control, and advanced media processing workloads where deterministic performance, ECC memory support, and integrated GbE/PCIe/USB connectivity simplify board design and reduce BOM. Key features of the P1022NXN2HFB include dual e500v2 cores with integrated L1/L2 caches, hardware ECC support for DDR2/DDR3 memories, three Gigabit Ethernet interfaces, multiple PCIe lanes, USB 2.0, an LCD controller for HMI, and a security engine. The device supports both DDR2 and DDR3 with ECC, addresses industrial-grade reliability requirements, and integrates DPAA-friendly acceleration blocks for packet inspection and crypto offload. Architecturally, the P1022NXN2HFB is built on a Power Architecture e500v2 core complex with a coherent fabric connecting the cores, memory controllers, and high-speed serial I/O. This design delivers application processing performance with simultaneous line-rate packet handling, eliminating the need for separate control-plane and data-plane processors in many embedded networking designs. Typical applications include industrial gateways and routers, factory automation controllers, networked HMI panels, smart-grid energy management, and secure edge appliances. The integrated peripherals reduce external chip count, while the extended temperature range enables deployment in harsh industrial environments. When designing with this MPU, allocate sufficient PCB area for the 31x31 mm TEPBGA II package, follow NXP's reference design for power decoupling and DDR routing, and verify that your firmware targets the e500v2 instruction set. The device is non-trivial to bring up; use NXP's BSP and SDK to accelerate software development. This page consolidates distributor pricing, lifecycle status, drop-in reference variants, and practical design guidance sourced from the NXP product page and authorized distributor inventories, going beyond the bare datasheet content alone.

RFQ Kontak
P1022NXN2LFB - QorIQ Dual-Core 1.067 GHz SoC | NXP | Networking
P1022NXN2LFB

P1022NXN2LFB - QorIQ Dual-Core 1.067 GHz SoC | NXP | Networking

The NXP P1022NXN2LFB is a dual-core QorIQ communications processor built on Power Architecture e500 cores, designed for IP networking and advanced media processing applications. Housed in a 689-ball TEPBGA package measuring 31 x 31 mm with 2.23 mm height, this SoC integrates dual 32-bit Power Architecture cores running up to 1.067 GHz, DDR2/DDR3 memory controllers with ECC support, Gigabit Ethernet, PCIe, USB 2.0, and an LCD controller. The part targets industrial temperature grade (-40 °C to +125 °C) operation in extended-temperature networking and industrial designs. A QorIQ processor is a system-on-chip (SoC) family within NXP's communications-platform portfolio, positioning it above discrete microcontrollers and below enterprise-class multi-core CPUs in the taxonomy: SoC -> communications processor -> QorIQ platform -> Power Architecture implementation. QorIQ parts are engineered specifically for high-throughput packet processing, secure networking, and intelligent edge gateways. The P1022 family sits in the value-tier of QorIQ, balancing dual-core performance with the integration of network and storage peripherals. Key features of the P1022NXN2LFB include 1067/533/667 ET NE r1.1 platform versioning, dual e500 cores with hardware MMU and 36-bit physical addressing, DDR2/DDR3 memory controller supporting up to 32-bit ECC, three 10/100/1000 Ethernet MACs, three PCIe Gen1 interfaces, USB 2.0 host/device, four TDM/I2S interfaces, and a 32-bit LCD controller. The integrated security engine supports symmetric and asymmetric crypto acceleration. Hardware virtualization is provided through the embedded hypervisor extensions. The P1022NXN2LFB is built on a 45 nm low-power process, with voltage rails between 3.13 V and 3.47 V at the core supply domain. The architecture combines a 256 KB shared L2 cache per core with a platform cache fabric, yielding determinism for control-plane workloads. Compared to the smaller P1013 (single-core), the P1022 adds a second e500 core for symmetric multiprocessing workloads, and compared to the P1020 the P1022 offers higher DDR frequency support. Typical applications include industrial routers and gateways, factory-floor protocol converters, smart-grid concentrators, multi-service access equipment, line cards for branch routers, military/aerospace networking, networked printers, and edge-of-network media gateways. Its extended temperature range and RoHS/halogen-free TEPBGA package make it suited to long-life industrial designs. When designing with this part, ensure the PCB supports the large 31 x 31 mm BGA land pattern, plan thermal vias under the exposed die area, and validate DDR3/DDR2 IBIS-AMI models for SI compliance on multi-rank memory subsystems.

RFQ Kontak
P1023NSN5CFB - QorIQ P1023 500MHz Dual-Core e500v2 MPU | NXP
P1023NSN5CFB

P1023NSN5CFB - QorIQ P1023 500MHz Dual-Core e500v2 MPU | NXP

The NXP P1023NSN5CFB is a QorIQ P1 communications processor based on the PowerPC e500v2 core, integrating two 32-bit cores running up to 500 MHz (core / DDR / platform frequencies of 500 / 333 / 667 MHz) in a 457-ball TEPBGA-1 (19x19 mm) package. The device targets networking, industrial control, and entry-level communications applications where deterministic response, integrated peripherals, and a long-life PowerPC architecture are required. A microprocessor (MPU) is a single-chip CPU containing the full arithmetic logic unit, control unit, register file, and on-chip caches of a computer. QorIQ P1 devices such as the P1023 sit at the entry tier of NXP's QorIQ Power Architecture portfolio (P1 -> P2 -> P3 -> P4 -> P5), positioned above simple microcontrollers (MCU) but below high-end Layerscape LX2/LX2160 communications processors. The P1023 bridges the gap between legacy PowerQUICC communications processors and modern QorIQ Layerscape families for cost-sensitive SMB/SOHO networking, factory automation, and secure connected devices. Key features include dual e500v2 cores with integrated 32 KB instruction and 32 KB data L1 caches per core, a unified 256 KB L2 cache, and integrated DDR2/DDR3 memory controller with ECC. The SoC also integrates three Gigabit Ethernet MACs (one RGMII + two SGMII), dual PCIe Gen1 controllers, USB 2.0, SD/MMC, SPI, I2C, UART, and an integrated security engine (SEC 3.x) for IPsec / SSL acceleration. The platform runs from a 1.0 V core supply with a 19x19 mm package suitable for standard 4-layer PCB stack-ups. Typical applications include entry-level routers, switches and gateways, industrial PLC controllers, factory automation nodes, secure POS terminals, and networked MFP/multifunction peripherals. The dual-core architecture with hardware-accelerated encryption makes the P1023 a frequent choice for SOHO/SMB firewall and UTM appliances where deterministic packet processing and a mature BSP ecosystem matter more than peak throughput. When designing with the P1023, ensure the 1.0 V core supply uses a buck converter with sufficient transient response to handle core load steps. DDR memory routing requires matched-length traces and proper termination per NXP's hardware design checklist; signal integrity on the two SGMII links is critical and usually demands a reference clock with low jitter. This page synthesizes authorized distributor pricing, available stock across DigiKey / Mouser / Rochester Electronics, drop-in alternatives from the same P1 family, and practical design notes not consolidated in the NXP product brief.

RFQ Kontak
P1024NSN5DFB - QorIQ P1 Dual-Core 667MHz SoC | NXP
P1024NSN5DFB

P1024NSN5DFB - QorIQ P1 Dual-Core 667MHz SoC | NXP

The NXP P1024NSN5DFB is a dual-core PowerPC e500v2 communications processor from the QorIQ P1 family, integrating two 32-bit cores operating up to 667 MHz in a 561-ball TEBGA-1 (23x23 mm) package. The device combines GbE, DDR3 with ECC memory controller, PCIe, USB 2.0, and TDM interfaces on a single 45 nm silicon die, delivering networking-grade compute at typical embedded power envelopes. A QorIQ communications processor is a system-on-chip (SoC) tailored for wired and wireless infrastructure, integrating CPU cores, packet processing accelerators, high-speed serial interfaces, and memory controllers in a single device. Within the broader taxonomy, the P1024 sits at: communications processor -> embedded SoC -> microprocessor -> integrated circuit -> semiconductor. This integration reduces BOM count, PCB area, and software complexity for OEMs building routers, switches, industrial gateways, and defense platforms. Key features of the P1024 include dual PowerPC e500v2 cores up to 667 MHz (533 MHz core / 333 MHz platform / 667 MHz data rate per Mouser description), integrated three-speed 10/100/1000 Ethernet controllers, a 64-bit DDR3 controller with ECC, two PCIe controllers, USB 2.0 host/device, TDM, SPI, I2C, DUART, and security engine acceleration. The 45 nm process enables low-power operation while supporting the industrial 0 to 125C junction temperature range, suitable for thermally constrained deployments. The 561-TEPBGA package provides high-density board integration at 23x23 mm. The architecture combines dual e500v2 cores with hardware-accelerated packet handling, queue management, and cryptography. The integrated security engine supports IPsec, SSL/TLS, and MACsec offload, offloading packet inspection from the cores and improving throughput per watt. This makes the P1024 well suited for line-rate encryption, deep-packet inspection, and control-plane processing in mid-range networking equipment. Typical applications include branch-office routers, industrial control gateways, defense and aerospace secure communications, factory automation controllers, and Smart Grid / IEC 61850 substation equipment. The combination of dual-core performance, hardware crypto, and industrial temperature range addresses the converged networking and embedded computing needs of these markets. When designing with the P1024, allocate sufficient PCB layers (at least 8) for the 561-ball BGA breakout and high-speed DDR3 routing. Use impedance-controlled traces for GbE, PCIe, and SERDES signals, and follow NXP hardware design guidelines for thermal management given the 23x23 mm package. This page synthesizes current distributor inventory, lifecycle status, drop-in alternatives within the QorIQ P1 family, and practical design considerations drawn from the manufacturer datasheet to help engineers evaluate the P1024NSN5DFB for production use.

RFQ Kontak
P1024NXE5BFB - QorIQ P1 Dual-Core 400MHz SoC | NXP
P1024NXE5BFB

P1024NXE5BFB - QorIQ P1 Dual-Core 400MHz SoC | NXP

The NXP P1024NXE5BFB is a dual-core QorIQ P1 communications processor built on 45 nm silicon-on-insulator technology, integrating two Power Architecture e500 cores running at 400 MHz inside a 561-ball TEPBGA package measuring 23x23 mm. The device delivers up to 800 MHz aggregate compute with hardware-accelerated security (SEC), GbE interfaces, DDR3 with ECC memory controller, PCIe, USB, and TDM peripherals, all in a single SoC. What is a QorIQ communications processor? The QorIQ family is NXP's line of Power Architecture-based system-on-chip devices that integrate CPU cores, memory controllers, networking peripherals, and security engines for wired/wireless infrastructure. In the hierarchy, a communications SoC like the P1024 sits above a generic microprocessor (MPU) and below a full network processor (NPU), filling the role of intelligent control plane and modest data-plane processing in routers, switches, base stations, and industrial gateways. Key features include dual e500 cores with 36-bit physical addressing, 32 KB I-cache and 32 KB D-cache per core, integrated SEC 4.0 security engine, dual 10/100/1000 Mbps Ethernet controllers, 32-bit DDR3/DDR3L memory controller with ECC, two PCIe controllers, one USB 2.0 with PHY, TDM serial interface, eSPI, and four I2C controllers. The device operates from -40C to +125C junction temperature and is targeted at industrial-grade extended-temperature networking equipment. Technically, the P1024NXE5BFB uses a high-performance superscalar e500v2 core with out-of-order execution, hardware table-walk MMU, and a 256 KB shared CoreNet platform cache. The Coherent Fabric crossbar eliminates main-memory access contention between cores, while the SEC block accelerates IPsec, SSL/TLS, and 3GPP wireless cipher suites for secure data-plane operations. Typical applications include industrial routers and gateways, LTE/small-cell base stations, defense and aerospace networking, network-attached storage (NAS) controllers, and secure VPN concentrators. The extended temperature range also suits outdoor industrial switches and grid infrastructure. When designing with the P1024NXE5BFB, plan a six-layer PCB for DDR3 routing with matched 50 ohm impedance. Use the on-chip SEC engine to offload IPsec processing and reserve e500 cycles for control-plane software. This page synthesizes distributor pricing, parameter analysis, and design considerations not found in the manufacturer datasheet alone, supporting engineers evaluating communications SoC alternatives.

RFQ Kontak
P1024NXN5DFB - QorIQ P1 Dual-Core 667MHz SoC | NXP Semiconductors
P1024NXN5DFB

P1024NXN5DFB - QorIQ P1 Dual-Core 667MHz SoC | NXP Semiconductors

The NXP (formerly Freescale) P1024NXN5DFB is a QorIQ P1 family communications processor based on the Power Architecture e500v2 core, integrating dual 32-bit cores operating up to 667 MHz in a 561-pin TEBGA I (23x23 mm) package. Per the verified distributor specification it combines GbE, DDR3 with ECC, PCIe, USB 2.0, TDM, and security engines, targeting industrial temperature operation from -40°C to +125°C, revision 1.1 silicon. A QorIQ communications processor is a system-on-chip (SoC) that integrates one or more Power Architecture CPU cores with high-speed networking peripherals, memory controllers, and accelerator blocks. The P1024NXN5DFB sits in the hierarchy: Power Architecture CPU -> QorIQ P1 SoC -> communications processor -> embedded networking MCU. It targets the same role as the older PowerQUICC III family but with significantly higher integration at 45 nm process geometry. Key features highlighted in the verified data include the dual-core e500v2 configuration, an internal core complex supporting up to 667 MHz operation, DDR3 memory controller with ECC for reliable networking memory, integrated Gigabit Ethernet MACs, PCI Express lanes, USB 2.0 controller, TDM/SGMII serial interfaces, and an industrial -40°C to +125°C operating range. The part is offered in tray packaging suitable for high-rel manufacturing. The P1024NXN5DFB is implemented on a 45 nm low-power CMOS process and includes hardware-accelerated cryptography, QUICC Engine packet handling, and RapidIO optional interfaces in the wider P1 family. Revision 1.1 silicon identifies the specific mask set, important for software/firmware compatibility and erratum tracking; engineers should validate Rev 1.1 against their BSP and SDK distributions. Typical applications include industrial routers, secure gateways, industrial Ethernet switches, defense and aerospace networking, telecom edge equipment, and industrial IoT controllers. The combination of dual-core processing and integrated GbE/PCIe makes it well-suited for L2/L3 managed switches and secure VPN gateways. When designing with this SoC, plan thermal management: at 667 MHz dual-core the part dissipates several watts and the TEBGA I package requires substantial PCB copper or airflow. Validate BSP/driver support for your Linux distribution and confirm that the 561-ball TEBGA I footprint matches your PCB design rules before committing to layout. This page synthesizes distributor pricing, lifecycle status (End-of-Life per the NXP product page), datasheet references, and practical design notes not consolidated on any single vendor page.

RFQ Kontak
P1025NSE5BFB - QorIQ P1025 667MHz Dual-Core PowerPC | NXP
P1025NSE5BFB

P1025NSE5BFB - QorIQ P1025 667MHz Dual-Core PowerPC | NXP

The NXP P1025NSE5BFB is a QorIQ P1 series communications processor featuring dual PowerPC e500v2 cores running at up to 667 MHz, packaged in a 561-pin TEPBGA I (23x23 mm). Built on 45 nm low-power process technology, the device integrates GbE controllers, DDR3 memory controller with ECC, PCI Express, USB, TDM, security (SEC), and QUICC Engine (QE) peripherals for networking, telecom, defense and industrial markets. A QorIQ communications processor (also known as a Power Architecture SoC or communications MPU) is a highly-integrated system-on-chip designed for packet processing, secure routing, and embedded control in networked equipment. It belongs to the broader family of embedded microprocessors (MPU) that combine one or more processor cores, memory controllers, high-speed I/O, and acceleration engines on a single die. Within NXP's portfolio, QorIQ P1 sits between the lower-cost P1015 family and the higher-performance P2/P4 families. Key differentiating features of the P1025NSE5BFB include dual 32-bit e500v2 cores (vs single-core P1016), 667 MHz operation, integrated hardware security engine, QUICC Engine for legacy TDM/UTOPIA support, and industrial temperature range from 0C to +125C. The combination of DDR3 with ECC and integrated GbE MACs makes it suitable for line cards, secure routers, and industrial gateways that demand deterministic throughput. Architecturally, the device uses a hierarchical interconnect that allows each e500v2 core to access L1 caches while sharing L2 and I/O subsystems. The 45 nm process provides a favorable power/performance balance for fanless industrial deployments where the larger 23x23 mm BGA helps spread thermal dissipation. Hardware accelerators offload crypto, pattern matching, and packet inspection from the cores. Typical applications include secure network routers, industrial Ethernet switches, defense communications equipment, factory automation controllers, LTE small-cell baseband, and smart-grid gateways. The dual-core configuration and QUICC Engine make it especially attractive where TDM/legacy interfaces must coexist with modern IP traffic. When designing with this part, allocate sufficient PCB layers (typically 8+), follow NXP AN-4320 for BGA routing, and place bulk decoupling capacitors within 2 inches of the power balls. Designers should refer to NXP's hardware specifications for the recommended DDR3 topology and SERDES termination network. This page synthesizes distributor pricing, drop-in alternatives from the QorIQ P1 family, and practical design notes not directly compiled in the manufacturer datasheet, giving engineers a single reference for evaluation, sourcing, and PCB layout considerations.

RFQ Kontak
P1025NSN5DFB - QorIQ P1 Dual-Core 667MHz PowerPC SoC | NXP
P1025NSN5DFB

P1025NSN5DFB - QorIQ P1 Dual-Core 667MHz PowerPC SoC | NXP

The NXP P1025NSN5DFB is a QorIQ P1 platform communications processor based on the Power Architecture e500v2 core, integrating two 32-bit cores operating up to 667 MHz in a 561-pin TEPBGA I (23x23) package. Built on a 45 nm process, this dual-core system-on-chip delivers integrated peripherals including Gigabit Ethernet, DDR3 memory controller with ECC, QUICC Engine (QE), PCIe, USB, and TDM interfaces for industrial and networking equipment. The QorIQ P1 platform series represents NXP's Power Architecture-based communications processor family targeting networking, telecom, defense, and industrial embedded applications. The P1025 specifically provides a dual-core solution within the 400 MHz to 667 MHz performance envelope, offering higher integration than discrete CPU-plus-MCU designs by collapsing networking, security, and connectivity silicon into a single device. The architecture inherits from the PowerQUICC III lineage, evolving the QUICC Engine subsystem into the enhanced QE block that handles serial protocol termination without consuming host CPU cycles. Key features of the P1025NSN5DFB include dual e500v2 cores at 533/333/667 MHz core-complex bus ratios, hardware virtualization support, integrated security acceleration, four GbE MACs, multiple high-speed serial interfaces, and a 32-bit DDR3 SDRAM controller with ECC. The 561-TEPBGA package exposes the full peripheral set, including SerDes lanes for PCIe and SGMII, while the thermal envelope is engineered for fan-less industrial designs operating from 0C to 125C junction temperature. The P1025NSN5DFB uses a hierarchical interconnect with the CoreNet coherency fabric shared by both e500v2 cores, allowing symmetric multiprocessing and coherent DMA from peripherals. The QUICC Engine subsystem offloads TDM, HDLC, UART, and BISYNC protocols, making the chip well suited for legacy telecom interfaces bridging into modern packet networks. Hardware-assisted encryption and integrity checking reduce CPU load on IPsec, SSL, and MACsec data planes. Typical applications include industrial routers and gateways, factory automation controllers, defense and aerospace networking equipment, smart-grid substation controllers, and multi-protocol telecom access systems. The dual-core configuration enables deterministic separation between control-plane and data-plane workloads, a key requirement in carrier-grade equipment where real-time protocol processing runs alongside management software. When designing with this device, allocate sufficient PCB area for the 23x23 mm BGA landing pattern, ensure controlled-impedance routing for SerDes and DDR3 signals, and follow NXP's hardware specifications for power-rail sequencing across the 1.0 V core and 1.5/1.8 V DDR3 supplies. The R1.1 designation refers to the silicon revision and must be matched across the BOM to ensure consistent errata behavior. This page synthesizes distributor stock data, lifecycle status, drop-in alternatives within the QorIQ P1 family, and design considerations not aggregated elsewhere, helping engineers source and qualify the P1025NSN5DFB quickly.

RFQ Kontak
P1025SSE5BFB - QorIQ P1025 400MHz PowerPC MPU | NXP | 561-TEPBGA
P1025SSE5BFB

P1025SSE5BFB - QorIQ P1025 400MHz PowerPC MPU | NXP | 561-TEPBGA

The NXP (formerly Freescale) P1025SSE5BFB is a QorIQ P1 series communications microprocessor based on the PowerPC e500v2 core, running at 400 MHz and housed in a 561-pin TEPBGA package (23x23 mm). It integrates dual PowerPC e500 cores, a QUICC Engine communications accelerator, hardware security engine SEC 3.3 with cryptography and random number generator support, and DDR2/DDR3 memory controller optimized for embedded networking and industrial control designs. A microprocessor (MPU) is a system-on-chip that integrates one or more CPU cores, memory controllers, peripheral interfaces and interconnect fabric onto a single die, allowing designers to build compact embedded systems without discrete processor plus chipset solutions. Within the broader taxonomy, the P1025 sits in the application processor tier between microcontrollers (single-purpose control) and high-performance SoCs (multi-core application processors); the QorIQ P1 family specifically targets industrial, networking and secure connectivity workloads. Key features include dual e500v2 cores at 400 MHz, 32-bit RISC architecture, integrated QUICC Engine for protocol offload, SEC 3.3 cryptographic acceleration including AES, 3DES, Kasumi and SNOW, integrated DDR2/DDR3 SDRAM controller with ECC support, PCI Express and Gigabit Ethernet MACs, and operating temperature range from 0C to 125C junction temperature. The 561-TEPBGA package provides high pin density for extensive I/O while remaining compatible with standard PCB assembly processes. Typical applications include industrial Ethernet switches, secure network routers, factory automation controllers, smart-grid gateways, and embedded industrial PCs requiring deterministic processing with hardware-accelerated cryptography. When designing with this device, allocate thermal copper under the package, use the recommended DDR trace length matching per NXP hardware specifications, and validate the QUICC Engine firmware integration against target protocol stacks early in the design cycle. This page synthesizes distributor pricing, application guidance and a practical design checklist beyond what is found in the manufacturer datasheet alone.

RFQ Kontak
P2010NSE2HFC - QorIQ P2 800MHz Power Arch SoC | NXP | Networking
P2010NSE2HFC

P2010NSE2HFC - QorIQ P2 800MHz Power Arch SoC | NXP | Networking

The NXP P2010NSE2HFC is a single-core 32-bit Power Architecture QorIQ P2 communications processor built on 45nm process technology, delivering 800 MHz of CPU frequency in a 689-ball TEBPGA II (31x31 mm) package. The device integrates a DDR2/DDR3 memory controller with ECC support, three Gigabit Ethernet controllers, three PCIe controllers, two Serial RapidIO (SRIO) interfaces, a USB 2.0 controller, and a security engine (SEC), making it suitable for wired and wireless networking, industrial control, and secure communications applications. What is a QorIQ communications processor? The QorIQ family is NXP's line of Power Architecture-based system-on-chip (SoC) devices that evolved from the PowerQUICC communications processor legacy. QorIQ P2 series parts like the P2010 are positioned for high-performance-per-watt networking applications and integrate general-purpose CPU cores, networking peripherals, and a memory controller in a single device. The platform is widely used in routers, switches, base stations, and industrial control systems where deterministic networking performance and integrated peripherals matter more than raw application-processor throughput. Key features of the P2010NSE2HFC include 800 MHz e500v2 CPU core, 32 KB I-cache and 32 KB D-cache per core, integrated SEC security accelerator supporting DES, 3DES, AES, RSA and ECC, and hardware pattern matching for QoS and traffic shaping. The device operates from a single supply rail and supports a junction temperature range of 0 to 125 degrees C (commercial extended), with the 'HFC' suffix indicating commercial temperature grade. The P2010NSE2HFC is pin-compatible with the dual-core P2020 and the lower-frequency P2010 variants, allowing a single PCB design to scale performance through component substitution. Its 45nm process technology yields low power dissipation (typically 4-6 W at 800 MHz) suitable for fanless designs in thermally constrained enclosures. Typical applications include entry-level to mid-range routers and switches, industrial Ethernet gateways, secure VPN concentrators, LTE/3G base station control plane processing, and factory automation controllers. The integrated SEC block makes it especially suitable for IPsec and SSL/TLS termination in network appliances. When designing with this device, ensure your PCB layout uses 1 oz copper on at least six layers with continuous power planes under the BGA, and provide at least 2 square inches of copper pour for thermal dissipation. Use NXP's CodeWarrior or QorIQ Linux SDK for software development, and validate the DDR3 interface timing with NXP's DDR3 register configuration tool before committing to layout. This page synthesizes distributor pricing, end-of-life context, pin-compatible alternatives within the QorIQ P2 family, and practical design considerations not consolidated in any single distributor or manufacturer page.

RFQ Kontak
P2010NSE2HHC - QorIQ P2010 800MHz e500v2 SoC | NXP
P2010NSE2HHC

P2010NSE2HHC - QorIQ P2010 800MHz e500v2 SoC | NXP

The NXP P2010NSE2HHC is a single-core QorIQ P2 series Power Architecture SoC running at 800 MHz (with 800 MHz core frequency) and housed in a 689-ball TEPBGA II package measuring 31x31 mm. Built on NXP's PowerPC e500v2 core architecture with a 32-bit datapath, it integrates dual DDR2/DDR3 memory controllers with ECC, Gigabit Ethernet, PCI Express, Serial RapidIO (SRIO), USB, and a security (SEC) engine on chip. An SoC (System-on-Chip) is an integrated circuit that consolidates CPU, memory controllers, and peripheral interfaces into a single silicon device, eliminating the multi-chip overhead typical of legacy processor-plus-coprocessor designs. The QorIQ P2010/P2020 family is NXP's communications-platform evolution of the PowerQUICC line, designed for high performance per watt in single- and dual-core networking, industrial control, and embedded computing applications. The series scales from a single-core 533 MHz P1011 to a dual-core 1.33 GHz P2020 while sharing one common pinout footprint. Key features include the e500v2 32-bit core with double-precision FPU, hardware ECC on the DDR2/DDR3 controller with up to 32-bit addressing, an integrated SEC security engine accelerating AES, 3DES, and SHA-1/2, four GbE ports, two PCIe controllers, two SRIO interfaces, USB 2.0 with PHY, and the Enhanced Local Bus Controller (eLBC). The 800 MHz core frequency is targeted at mainstream wired/wireless infrastructure, factory automation, and defense/aerospace subsystems. The P2010NSE2HHC operates across 0 to 125 C junction temperature per the NXP datasheet, making it suitable for thermally demanding industrial enclosures and outdoor telecom equipment. The TEPBGA II package exposes a thermal pad on the top side for direct heatsink attachment, while the 31x31 mm body accommodates 689 balls on a 1 mm pitch for high-density PCB layouts. Typical applications include industrial Ethernet switches, ruggedized military routers, factory automation controllers, and multi-protocol industrial gateways where deterministic real-time performance and long product lifecycles are required. The integrated SEC engine and ECC-protected memory also suit secure payment terminals and railway signaling. When designing with this device, follow NXP reference-design power-sequencing guidelines and ensure the exposed-pad thermal interface carries sufficient copper pour or an attached heatsink to keep junction temperature in spec under worst-case operating loads.

RFQ Kontak
P2010NSE2KHC - QorIQ P2010 e500v2 MPU 1.2GHz 689-TEBGA II | NXP
P2010NSE2KHC

P2010NSE2KHC - QorIQ P2010 e500v2 MPU 1.2GHz 689-TEBGA II | NXP

The NXP P2010NSE2KHC is a QorIQ P2010 communications processor featuring a single-core 32-bit Power Architecture e500v2 core running at 1.2 GHz, integrated into a 689-ball TEBGA II (31x31 mm) package with exposed pad for thermal dissipation. Built on 45 nm process technology, this SoC delivers high performance per watt for single-core networking and embedded communications applications, with on-chip peripherals including GbE, PCIe, Serial RapidIO (SRIO), USB and SEC 3.3 cryptography acceleration. The QorIQ P2 platform is an evolution of the PowerQUICC communications-processor family. A QorIQ MPU (microprocessor unit) is a SoC that combines one or more Power Architecture cores with the memory controllers, serial interfaces and packet-processing engines required by routers, switches, base stations and other networking infrastructure equipment. The P2010 sits at the entry of the P2 series, occupying a 4.5x aggregate frequency range within the same pinout as the dual-core P2020 up to 1.33 GHz and the smaller P1 (P1011 at 533 MHz) devices. Key features include an integrated DDR2/DDR3 memory controller with ECC support, dedicated security engine (SEC 3.3) for bulk encryption, two GbE controllers with TCP/IP offload, two PCIe Gen 1 controllers and a single USB 2.0 interface. The device operates across the 0 C to 125 C junction temperature range as required by NXP's industrial/extended-temperature specifications, making it suitable for outdoor or thermally-constrained telecom environments. The architecture pairs an e500v2 core with NXP's enhanced peripheral set, including dual I2C, dual UART, SD/MMC host and a 16-bit local bus. The 689-TEBGA II package supports high-speed SERDES and DDR3 traces while exposing a thermal pad that, when soldered to a properly-sized copper land pattern, keeps junction temperature within safe limits across the full operating range. Typical applications include entry-level edge routers, industrial control gateways, single-board computers for railway and energy systems, networked printing and imaging equipment, and secure communications appliances in industrial and defense systems where deterministic processing and hardware-accelerated encryption are valued. When designing with this device, engineers must implement a 6-layer PCB at minimum to route the DDR3 controller and SERDES lanes cleanly. The exposed thermal pad must be soldered to a continuous copper pour with thermal vias; failure to do so triggers thermal shutdown above the rated temperature. Designers reusing P1011, P2020 or P2010 layouts in the same TEBGA II footprint should follow NXP's hardware specifications for SERDES reference clock jitter and DDR3 length-matching, since the same footprint spans three performance grades. This page synthesizes distributor inventory, NXP datasheet specifications, drop-in compatible QorIQ P1/P2 siblings and practical design notes that go beyond the manufacturer datasheet, helping engineers select the right QorIQ tier for their target performance budget.

RFQ Kontak
P2010NSE2MFC - QorIQ P2010 1.2GHz e500v2 SoC | NXP Semiconductors
P2010NSE2MFC

P2010NSE2MFC - QorIQ P2010 1.2GHz e500v2 SoC | NXP Semiconductors

The NXP (formerly Freescale) P2010NSE2MFC is a single-core QorIQ P2 communications processor built on Power Architecture technology, integrating a 32-bit e500v2 core running at 1.2 GHz in a 689-ball TEPBGA II (31x31 mm) package with exposed pad. The device delivers high performance per watt for wired networking, industrial control, and single-core communications applications where deterministic throughput and integrated peripherals are required. A communications SoC (System-on-Chip) integrates a CPU core, memory controller, and multiple high-speed peripherals such as Gigabit Ethernet, PCIe, Serial RapidIO (SRIO), USB, and Security Engine (SEC) into a single die. The QorIQ P2010 belongs to the QorIQ P2 sub-family within NXP's Power Architecture communications processor hierarchy, occupying the slot between the lower-frequency P1 family (e.g., P1011) and the dual-core P2020. The MFC (Rev 2.1) suffix denotes a specific silicon revision with a fixed feature set. Key features of the P2010NSE2MFC include a 32-bit e500v2 core at 1.2 GHz, a DDR2/DDR3 memory controller with ECC support, three Gigabit Ethernet controllers (one with 10/100/1000 + 10/100 + 10/100), three PCI Express controllers, two Serial RapidIO interfaces, a USB 2.0 controller, a Security Engine (SEC), and a 0 to 125 °C extended operating temperature range. The 45 nm process technology balances performance against thermal dissipation, and the 689-TEPBGA II package supports high-density board layouts. The architecture uses a hierarchical interconnect that ties the e500v2 core to the L2 cache and peripheral controllers. Hardware acceleration offloads common data-plane tasks from the CPU, allowing sustained throughput on multi-gigabit Ethernet and SRIO links. The integrated SEC accelerates encryption protocols used in secure networking equipment. Typical applications include industrial routers and switches, factory automation controllers, defense and aerospace single-board computers, and telecom line cards where deterministic single-core Power Architecture performance and rich peripheral integration are required. When designing with this device, allocate adequate thermal dissipation because the 689-TEPBGA package concentrates heat; the exposed pad must be soldered to a continuous ground/power plane. Confirm voltage rail sequencing and use ECC-enabled DIMMs when reliability is required. This page synthesizes distributor pricing, drop-in alternatives within the QorIQ P2 family, and practical design notes not consolidated in the manufacturer datasheet.

RFQ Kontak
P2010NSN2MFC - QorIQ P2010 1.2GHz PowerPC e500v2 SoC | NXP
P2010NSN2MFC

P2010NSN2MFC - QorIQ P2010 1.2GHz PowerPC e500v2 SoC | NXP

The NXP P2010NSN2MFC is a QorIQ P2010 communications processor built on 45nm process technology, integrating a single PowerPC e500v2 core running at up to 1.2 GHz with 32-bit Power Architecture instruction set support. The device is packaged in a 689-ball TE-PBGA II (31x31 mm) with exposed pad, and combines a high-performance CPU subsystem with on-chip DDR2/DDR3 memory controllers (with ECC), Gigabit Ethernet, PCI Express, Serial RapidIO, and USB interfaces. Core voltage is 1.05 V; the operating temperature range spans 0 °C to +125 °C. Lead-free / RoHS compliant per the manufacturer datasheet. A communications processor (CPU/MPU) is a system-on-chip that integrates one or more processor cores, memory controllers, and high-speed serial peripherals on a single die for networking and embedded applications. Within the broader taxonomy, the P2010 sits in the MPU (microprocessor unit) class of microcontrollers and processors, which itself belongs to the wider category of embedded processors used in routers, switches, wireless base stations, industrial gateways, and similar network-edge equipment. The QorIQ family superseded NXP/Freescale's PowerQUICC line, and the P2010 is one of the entry/single-core members of the P-series. Key differentiating features include its pin-compatibility with the QorIQ P1 family (P1011/P1020/P1013/P1014/P1017/P1021/P1022/P1010/P1012), its integrated ECC-capable DDR2/DDR3 controller, and a four-tier frequency scaling option that lets OEMs standardize one PCB across multiple SKUs. The exposed-pad TE-PBGA II package supports high-power thermal dissipation for the 1.2 GHz speed grade. Architecturally, the P2010 uses the e500v2 core with double-precision FPU, hardware MMU, and a coherent fabric connecting the core to platform peripherals. The 45 nm silicon process provides a useful balance between performance and leakage for thermally constrained designs. Security is augmented by NXP's Trust Architecture and on-chip SEC engine (Lite) for crypto offload in secure boot and IPSec paths. Typical applications include industrial routers, factory automation gateways, smart-grid concentrators, line cards for access/edge networking, and any embedded Linux / VxWorks design that needs GbE plus PCIe plus a deterministic embedded OS footprint. The part is also used in wireless backhaul and small-cell infrastructure. As the device is approaching end-of-life per NXP's product page, long-life industrial designs should evaluate the recommended replacement (NXP recommends migration to the newer QorIQ LS series for new programs). Estimated: at 1.05 V core and 1.2 GHz, the P2010's typical power consumption is approximately 5-7 W depending on workload and I/O utilization. Designers must provide adequate copper area on the PCB top layer for the 31x31 mm BGA exposed pad to keep junction temperature below +125 °C. This page consolidates distributor pricing, lifecycle status, drop-in compatible QorIQ family variants, and PCB-level design notes that go beyond the bare datasheet extract — content tailored for engineers evaluating the P2010NSN2MFC for new designs or migration to the recommended NXP replacement.

RFQ Kontak
P2010NXE2KFC - QorIQ 1GHz e500v2 SoC, 689-TEPBGA | NXP
P2010NXE2KFC

P2010NXE2KFC - QorIQ 1GHz e500v2 SoC, 689-TEPBGA | NXP

The NXP P2010NXE2KFC is a single-core QorIQ P2 communications processor built on Power Architecture e500v2, operating up to 1.2 GHz core frequency, packaged in a 689-pin TEPBGA II (31 x 31 mm) with exposed pad for thermal dissipation. What is a QorIQ communications processor? The QorIQ platform is NXP's (formerly Freescale's) Power Architecture-based system-on-chip (SoC) family designed for networking, industrial control, and embedded communications workloads. QorIQ devices integrate one or more Power Architecture cores, memory controllers, Ethernet MACs, PCIe, Serial RapidIO (SRIO), USB, security engines, and various peripheral interfaces into a single BGA package, replacing multi-chip designs and reducing board area and system power. The P2 series sits in the performance tier above the P1 family, with frequencies up to 1.33 GHz, DDR2/DDR3 memory with ECC, and hardware-accelerated SEC 3.3 cryptographic offload. Key features of the P2010NXE2KFC include a single 32-bit e500v2 core with double-precision floating point, integrated DDR2/DDR3 memory controller with ECC support, three 10/100/1000 Mbps Enhanced Three-Speed Ethernet (eTSEC) controllers with IEEE 1588 timestamping, four lanes of PCI Express Gen 1/2, one x4 Serial RapidIO 1.2 interface, USB 2.0, two I2C controllers, two DUARTs, and a SEC 3.3 security engine for accelerated IPsec, SSL, TLS, and other cryptographic protocols. The wide I/O integration lets a single SoC replace what previously required a CPU plus external bridge, PHY, and security ASICs. Architecturally, the P2010NXE2KFC leverages 45 nm process technology, dual-issue in-order execution pipelines, 32 KB L1 instruction cache and 32 KB L1 data cache per core, plus a unified 512 KB L2 cache with ECC. The integrated SEC 3.3 engine provides transparent encryption, public-key acceleration (RSA, ECC), and random-number generation at wire speed, making the part a common choice for VPN gateways, industrial firewalls, and secure routers. Industrial-grade temperature range of -40 °C to +125 °C makes the P2010NXE2KFC suitable for harsh-environment deployments. Typical applications include industrial routers and gateways, networked factory equipment with EtherCAT or PROFINET bridges, secure VPN concentrators, single-board computers for medical imaging, telecom line cards, and defense/aerospace embedded controllers. Pin compatibility with the higher-frequency P2020 family and lower-power P1011/P1021 devices allows a single PCB design to scale across four performance points. Designers should plan thermal management carefully: even at 1 GHz a continuous 6 W+ dissipation through a 689-ball BGA requires a 4-layer PCB minimum with continuous ground plane beneath the exposed pad and a thermal interface material (TIM) connected to a heatsink or chassis. Decoupling requires 0402/0603 ceramics placed inside the BGA footprint shadow, and DDR routing must keep the 32-bit data bus matched within 25 ps to preserve DDR3-800 timing margins. This page aggregates NXP official specifications, distributor pricing, and drop-in alternatives sourced from the QorIQ P2 family datasheet - information that goes beyond what any individual distributor listing provides.

RFQ Kontak