Entegre Devreler

PIC18F14Q41-E/REB

PIC18F14Q41-E/REB - 8-bit 64MHz MCU, 16KB Flash, 20-VQFN | Microchip

The Microchip Technology PIC18F14Q41-E/REB is an 8-bit PIC18 microcontroller built around a 64 MHz core, integrating 16 KB of Flash program memory, 1 KB of SRAM and 512 bytes of EEPROM, and packaged in a compact 20-pin VQFN (3x3 mm) with an exposed thermal pad. The device belongs to the PIC18-Q41 family and is targeted at sensor-conditioning, lighting-control, and real-time-control designs that benefit from advanced on-chip analog. What is an 8-bit PIC microcontroller? An 8-bit MCU is a microprocessor core with an 8-bit data path, FLASH program memory, on-chip RAM and a peripheral set tuned for deterministic, low-latency control. PIC18 devices add a 16-bit instruction word, hardware multiplier and prioritized interrupts while retaining the small footprint and low power consumption of the PIC family, sitting within the hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. Key features include an on-chip operational amplifier (OPA), a 12-bit ADC with Computation (ADCC) for automated averaging, threshold compare and oversampling, an 8-bit DAC, two 8-bit timers, one 16-bit timer/PWM, DMA, and Peripheral Pin Select (PPS) for flexible signal routing. The device also integrates a configurable logic cell, complementary waveform generator (CWG), numerically controlled oscillator (NCO) and zero-cross detect, supporting fan/motor and lighting applications. The architecture pairs the enhanced mid-range PIC18 core with Core Independent Peripherals (CIPs), allowing ADCC, PWM, DMA and CWG to operate without CPU intervention. PPS remaps digital I/O to most pins, simplifying PCB routing in dense 3x3 mm layouts, and the 64 MHz internal oscillator eliminates the need for an external crystal in cost-sensitive designs. Typical applications are LED lighting drivers, sensor signal-conditioning front-ends, small appliance controls, fan/blower motor control, and IoT edge-node acquisition. Industrial-grade -40C to +125C operation supports factory and automotive sub-system environments. Designers should bias unused pins to defined states and follow Microchip AN2602 guidelines for VQFN-20 land pattern and thermal via arrays. The on-chip OPA and 12-bit ADCC combination typically eliminates one external op-amp, reducing BOM and PCB area by approximately 10-20% versus discrete analog front-ends. This page synthesizes distributor pricing, drop-in alternatives, application notes, and practical design notes that go beyond the manufacturer datasheet to help engineers select and qualify the part faster.

RFQ İletişim

PIC18F14Q41-E/SO

PIC18F14Q41-E/SO - 8-Bit 64MHz 16KB Flash MCU | Microchip

The Microchip Technology PIC18F14Q41-E/SO is an 8-bit RISC microcontroller from the PIC18-Q41 product family featuring a PIC18 CPU core running at up to 64 MHz, housed in a 20-pin SOIC package. It integrates 16 KB of Flash program memory, 1 KB of SRAM, and 512 bytes of EEPROM data memory, complemented by four DMA channels, two 8-bit DACs, and 17 channels of 12-bit ADC with computation (ADCC). The on-chip peripherals include an operational amplifier, configurable logic cells, and 16-bit PWM modules suitable for advanced sensor and real-time control applications. An 8-bit microcontroller (MCU) is a single-chip computer built around a CPU with an 8-bit data path, integrated program memory, RAM, and peripherals. PIC18 microcontrollers belong to Microchip's high-performance 8-bit family, positioned between simpler PIC16 devices and 16-bit dsPIC controllers. They are widely used in cost-sensitive embedded designs where deterministic interrupt response, low power consumption, and rich peripheral integration outweigh the throughput of 32-bit cores. The Q41 family specifically targets analog-intensive and mixed-signal applications with built-in op-amps, high-resolution PWM, and high-channel-count ADCs. Key features include 18 general-purpose I/O pins with Peripheral Pin Select (PPS) for flexible signal routing, UART, SPI, and I2C communication interfaces, and a wide 1.8V to 5.5V operating voltage range. The device supports up to 64 MHz operation from internal or external clock sources and includes multiple low-power modes for battery-driven applications. The PIC18F14Q41 leverages an enhanced Harvard architecture with separate code and data buses, instruction pipelining, and a hardware multiplier. The 12-bit ADCC with hardware averaging and threshold detection reduces CPU overhead for sensor acquisition, while the integrated op-amp enables direct signal conditioning without external amplifiers. Typical applications include industrial sensor nodes, IoT edge devices, LED lighting controllers, motor control subsystems, and battery-powered portable instruments. Designers value the part for compact designs needing strong analog performance in a small footprint. When designing with this device, ensure the ICSP programming pins are accessible for in-circuit firmware updates and that the exposed pad (if present on the package variant) is soldered to the thermal plane for optimal heat dissipation. This page synthesizes distributor pricing, drop-in PIC18 family alternatives, and practical design notes not consolidated in the manufacturer datasheet.

RFQ İletişim

PIC18F14Q41-I/P

PIC18F14Q41-I/P - 8-bit MCU, 16KB Flash, 64MHz, 20-PDIP | Microchip

The Microchip Technology PIC18F14Q41-I/P is a high-performance 8-bit RISC microcontroller from the PIC18-Q41 family, offering 64MHz operation with 16KB of Flash program memory in a 20-pin PDIP through-hole package. It integrates 1KB of data RAM, 512 bytes of data EEPROM, and a rich analog and digital peripheral set aimed at sensor and real-time control applications. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path and an integrated CPU core, Flash program memory, RAM, and a fixed set of peripherals. It sits within the broader hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The PIC18 architecture extends the baseline PIC16 instruction set with C-friendly addressing, a hardware multiplier, and a linear program memory map, making it well suited to mid-complexity firmware in industrial, consumer, and IoT endpoints. Key features of the PIC18F14Q41-I/P include an on-chip operational amplifier, a 12-bit differential Analog-to-Digital Converter with Computation (ADCC), an 8-bit DAC, a 16-bit PWM module, DMA-driven data movement, UART, SPI, and I2C interfaces, plus Peripheral Pin Select (PPS) for flexible signal routing. The device operates across an industrial temperature range, supporting harsh-environment deployments. The 20-pin PDIP package allows easy prototyping and breadboard work while exposing the full peripheral set. Technically, the PIC18F14Q41 implements a Harvard architecture with separate program and data buses, a 16-bit instruction word, and a vectored interrupt controller with multiple priority levels. The 12-bit ADCC supports oversampling and averaging in hardware, offloading noise reduction from the CPU. PPS remaps most digital peripherals onto a wide choice of I/O pins, simplifying PCB routing when multiple functions must share a limited pin budget. Typical applications include sensor signal conditioning, closed-loop motor and lighting control, general-purpose embedded control, small user-interface controllers, and battery-powered IoT nodes that benefit from the integrated op-amp and high-resolution ADC. The combination of DMA, ADCC, and 16-bit PWM enables responsive control loops without burdening the core. When designing with this part, validate that the 20-pin PDIP package offers sufficient I/O for the application and confirm the device's supply-voltage range against the chosen analog reference. PPS should be configured in code at startup to avoid bus contention. This page synthesizes distributor pricing, package-equivalent Microchip variants, and practical design notes not found in the manufacturer datasheet.

RFQ İletişim

PIC18F14Q41-I/SO

PIC18F14Q41-I/SO - 8-bit 64MHz MCU 16KB Flash 20-SOIC | Microchip

The Microchip Technology PIC18F14Q41-I/SO is a compact, high-performance 8-bit PIC18 microcontroller operating at up to 64 MHz with 16 KB of Flash program memory, 1 KB of SRAM, and 512 bytes of EEPROM, housed in a 20-pin SOIC package. The PIC18-Q41 family integrates advanced analog peripherals including a 12-bit ADC with computation (ADC2), dual 8-bit DACs, a 16-bit PWM, an on-chip operational amplifier, and a configurable logic cell, making it well suited for sensor and real-time control applications. A PIC18 microcontroller is an 8-bit Harvard-architecture RISC MCU from Microchip's PIC18 family, sitting in the broader taxonomy of 8-bit microcontroller -> microcontroller -> embedded processor -> semiconductor. The PIC18 core executes most instructions in a single cycle with a hardware multiplier and a 31-level stack, balancing deterministic real-time control with rich peripheral integration. Within the power management and signal-chain subsystem of a product, the MCU acts as the sensing-and-actuation brain, replacing discrete analog hardware with software-configurable analog blocks. Key features of the PIC18F14Q41-I/SO include 18 general-purpose I/O pins, an enhanced mid-range core with a C compiler-friendly instruction set, an on-chip op-amp, zero-cross detection, a complementary waveform generator (CWG) for motor and power conversion, and support for 1.8 V to 5.5 V operation. The device integrates a 12-bit differential ADC with oversampling and a computation engine for automated averaging and threshold comparisons. The PIC18F14Q41 architecture pairs a 64 MHz internal oscillator with peripheral pin select (PPS) remappable I/O, allowing flexible board layouts. Its nanoWatt XLP technology delivers low-power sleep currents in the nanoamp range, supporting battery-backed sensing nodes. The on-chip op-amp, comparators, and DACs enable closed-loop analog control without external amplifiers, reducing BOM cost and PCB area. Typical applications include sensor signal conditioning, LED lighting control with smooth dimming, low-end motor control (fan, pump, small BLDC), battery-powered IoT nodes, and white-goods user-interface controllers. The compact 20-SOIC package supports hand-solderable prototypes and high-volume automated assembly. Designers should pay attention to the analog pin assignments and PPS mapping: the on-chip op-amp inputs are shared with specific ADC channels, and the CWG outputs occupy fixed pins. A 100 nF decoupling capacitor as close as possible to VDD, plus a 10 uF bulk capacitor, is recommended. This page combines authoritative manufacturer specifications, current distributor pricing, drop-in compatible alternatives, and practical design notes that are not assembled in any single source on the web, providing a faster engineering evaluation path than the datasheet alone.

RFQ İletişim

PIC18F14Q41-I/SS

PIC18F14Q41-I/SS - 8-bit 64MHz 16KB Flash MCU | Microchip

The Microchip Technology PIC18F14Q41-I/SS is an 8-bit RISC microcontroller from the PIC18-Q41 product family, featuring a high-performance PIC18 CPU core operating at up to 64 MHz, 16 KB of Flash program memory, 1 KB of SRAM, and 512 bytes of EEPROM, housed in a 20-pin SSOP package. The device integrates advanced analog peripherals including a 12-bit ADC with Computation (ADC2), two 8-bit DACs, an on-chip operational amplifier, comparators, a 16-bit PWM, and a 10-bit PWM, making it well suited to closed-loop sensor and real-time control applications. Per the Microchip product page, the Q41 family is positioned for compact designs where integrated analog replaces external signal-conditioning components, and the SSOP-20 footprint (208 mil body width) eases hand-soldering and breadboard prototyping. A microcontroller (MCU) is an integrated circuit that combines a CPU, program and data memory, and configurable peripherals on one die. The 8-bit MCU class prioritises deterministic interrupt latency, low power consumption, and predictable I/O behaviour over raw computational throughput, and remains dominant in cost-sensitive embedded designs where the application fits within the address space. PIC18 devices extend the classic PIC16 instruction set with linear addressing and a larger register file, retaining the RISC-style single-cycle instruction execution that has defined the PIC architecture for decades. Within the broader power-management and embedded hierarchy, PIC18F14Q41 belongs to the microcontrollers segment, with deep ties to the wider Microchip 8-bit and 16-bit dsPIC ecosystem. Key features include up to 64 MHz operation from a 1.8 V to 5.5 V supply, on-chip op-amp and zero-cross detector, multiple communication interfaces (UART, SPI, I2C), up to 18 I/O pins, and integrated Core Independent Peripherals (CIPs) that offload timing-critical tasks from the CPU. The device supports in-circuit serial programming (ICSP) via high-voltage or low-voltage interfaces, enabling firmware updates in the field without package removal. Architecturally, the PIC18F14Q41 uses a Harvard architecture with separate program and data buses, a hardware multiplier, and an 8-level deep hardware stack. The ADC2 peripheral performs automated averaging, threshold comparisons, and burst-mode sampling, reducing firmware overhead for sensor acquisition. The integrated op-amp can be routed to the ADC input or comparator, eliminating an external amplifier stage in many sensor-interface designs. Typical applications include industrial sensor conditioning, building automation, lighting control, low-cost motor control, and battery-powered IoT edge nodes. The wide 1.8 V to 5.5 V supply range supports direct connection to single-cell Li-Ion or 3.3 V system rails. When designing with this device, allocate decoupling capacitance close to VDD and AVSS pins, route analog signals away from switching nodes, and follow Microchip's Q41 family layout guidelines to minimise ADC noise pickup. This page synthesises distributor pricing, drop-in same-package alternatives, and practical design notes not aggregated on the manufacturer product page or individual distributor listings.

RFQ İletişim

PIC18F14Q41T-I/SO

PIC18F14Q41T-I/SO - 8-bit 64MHz 16KB Flash MCU | Microchip

The Microchip Technology PIC18F14Q41T-I/SO is an 8-bit PIC18 microcontroller IC running up to 64 MHz with 16 KB (16K x 8) of Flash program memory, 1 KB of SRAM, and 512 bytes of EEPROM, housed in a 20-pin SOIC package. It is part of the PIC18-Q41 family, which is described by Microchip as a compact, high-performance PIC18 product family with advanced analog peripherals for sensor and real-time control applications. What is a PIC18 8-bit microcontroller? A PIC18 microcontroller is an 8-bit Harvard-architecture MCU from Microchip Technology built on a modified RISC core with a rich peripheral set. Within the broader taxonomy, PIC18 sits inside PIC microcontrollers -> microcontrollers -> embedded ICs -> integrated circuits -> semiconductors. The Q41 family in particular targets mixed-signal applications by integrating a 12-bit ADC with computation (ADCC), an 8-bit DAC, an on-chip operational amplifier, DMA, and configurable peripherals via Peripheral Pin Select (PPS). Key features include a 12-bit ADCC for high-resolution analog measurements, an 8-bit DAC, an on-chip op-amp for signal conditioning, a 16-bit PWM for precision motor and lighting control, Direct Memory Access (DMA) for offloading the CPU, and PPS for flexible pin assignments. The on-chip op-amp and ADCC combination is designed to minimize external analog components in sensor and closed-loop control designs. The device operates from 2.3V to 5.5V, supports UART, SPI, and I2C communication interfaces, and includes Core Independent Peripherals (CIPs) that allow complex functions to run without CPU involvement. The 64 MHz internal oscillator enables high-speed operation without an external crystal in many designs. Typical applications include sensor signal conditioning with on-chip op-amp + ADC, BLDC/PMSM motor control using the 16-bit PWM, LED lighting control, IoT edge nodes, and small appliance control boards. When designing with this part, leverage PPS to route peripherals to available pins and use the on-chip op-amp to eliminate external analog stages. The DMA controller can significantly reduce CPU load in high-throughput ADC or communication tasks. This page synthesizes distributor pricing, verified drop-in alternatives from Microchip's PIC18 family, and practical design notes not found in the manufacturer datasheet.

RFQ İletişim

PIC18F15Q40-E/P

PIC18F15Q40-E/P - 8-bit 64MHz 32KB Flash MCU | Microchip

The Microchip Technology PIC18F15Q40-E/P is an 8-bit RISC microcontroller featuring the PIC18 CPU core operating at up to 64MHz, housed in a 20-pin PDIP (P) through-hole package. The device integrates 32KB of Flash program memory, 2KB of data SRAM, and 512 bytes of data EEPROM, making it suitable for compact real-time control and sensor applications. The -E temperature grade supports an operating range of -40C to +125C. What is a PIC microcontroller? A PIC (Peripheral Interface Controller) microcontroller is a compact, low-cost, self-contained computer-on-a-chip that integrates a CPU core, non-volatile program memory, working RAM, EEPROM, and a rich set of analog and digital peripherals into a single IC. PIC MCUs sit within the broader embedded microcontroller hierarchy (8-bit MCU -> microcontroller -> embedded processor -> semiconductor), and the PIC18 family is Microchip's mainstream 8-bit line balancing cost, performance, peripheral integration, and code density via an enhanced 16-bit instruction word. Key differentiating features of the PIC18F15Q40 include a 12-bit ADC with Computation (ADCC) for automated averaging, threshold detection, and filtering; dual 8-bit DACs for analog output generation; 16-bit PWMs with multiple modes for motor, lighting, and power control; Direct Memory Access (DMA) to offload CPU data movement; Configurable Logic Cells (CLC) for hardware glue logic; and Peripheral Pin Select (PPS) for flexible signal routing. The device also offers UART, SPI, and I2C communications. Architecturally, the PIC18F15Q40 uses an enhanced Harvard architecture with separate program and data buses, hardware multiply, and a 31-level deep hardware stack. The 12-bit ADCC provides oversampling and burst-averaging modes, enabling high effective resolution. The combination of DMA, CLC, and PPS creates a deterministic, low-CPU-overhead platform ideal for closed-loop control. Typical applications include sensor signal conditioning, LED lighting control, low-cost motor control, battery management front-ends, and industrial IoT edge nodes. The wide temperature range and PPS flexibility make it a fit for harsh industrial environments. When designing, allocate careful PCB attention to the AGND/AVDD analog rails if using the ADCC; place the recommended 0.1uF + bulk decoupling within 5mm of each VDD pin and follow Microchip AN4553 for ADCC layout practices.

RFQ İletişim

PIC18F15Q40-E/REB

PIC18F15Q40-E/REB - 8-Bit 64MHz MCU, 32KB Flash, 20-VQFN | Microchip

The Microchip Technology PIC18F15Q40-E/REB is a high-performance 8-bit PIC18 microcontroller featuring a 64MHz CPU, 32KB of Flash program memory, 2KB of SRAM, and 512 bytes of EEPROM, all housed in a compact 20-pin VQFN (3x3 mm) package. It integrates advanced peripherals including a 12-bit ADC with Computation (ADCC) supporting capacitive voltage divider touch sensing, two 8-bit DAC modules, 16-bit Pulse-Width Modulation (PWM) channels, four DMA channels, two comparators, and Configurable Logic Cells (CLC) for hardware-based state machine implementation. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory, and programmable peripherals on one IC. The PIC18F family is built on an enhanced 8-bit RISC Harvard architecture that balances deterministic interrupt response, low power consumption, and ease of programming in C or assembly. Within the broader taxonomy, an 8-bit MCU like the PIC18F15Q40 sits between simple 8-bit controllers and 16-/32-bit MCUs, making it ideal for cost-sensitive real-time control applications that demand more peripheral integration than a basic PIC10/PIC12 device but do not justify the cost of an ARM Cortex-M0 part. Key features include 17 channels of 12-bit ADC with computation capabilities, hardware-accelerated averaging/filtering/oversampling/threshold comparison, two 8-bit DACs for analog signal generation, multiple communication interfaces including UART, SPI, and I2C, plus 9 timers and 3 PWM modules. The device operates from 1.8V to 5.5V supply, supports extended temperature range from -40C to +125C, and includes on-chip debugging via MPLAB ICD. The PIC18-Q40 architecture combines a high-throughput 8-bit core with rich analog integration, making it well suited for sensor-based designs. Configurable Logic Cells allow glue-logic replacement directly in hardware, while DMA offloads repetitive data movement from the CPU, freeing cycles for application code. Typical applications include consumer appliance control, capacitive touch user interfaces, sensor node data acquisition, motor control loops, LED lighting controllers, and battery-powered IoT edge devices. The wide 1.8V-5.5V supply range supports both single-cell lithium battery operation and traditional 5V systems. When designing with the PIC18F15Q40-E/REB, ensure that unused pins are configured as outputs or pulled appropriately to minimize power consumption. The CLC modules can replace discrete logic gates to reduce BOM cost and PCB area in mixed-signal designs. This page synthesizes verified distributor pricing, drop-in same-package alternatives, and practical design guidance beyond the manufacturer datasheet, supporting engineers in component selection and BOM optimization.

RFQ İletişim

PIC18F15Q40-E/SO

PIC18F15Q40-E/SO - 8-Bit 64MHz MCU, 32KB Flash 20-SOIC | Microchip

The Microchip Technology PIC18F15Q40-E/SO is an 8-bit PIC18-Q40 family microcontroller running up to 64 MHz with 32 KB of Flash program memory, 2 KB of SRAM, and 512 bytes of EEPROM in a 20-pin SOIC (SO) wide-body package. The part integrates a 12-bit ADC with Computation (ADCC), two 8-bit DACs, 16-bit PWMs, Direct Memory Access (DMA), Configurable Logic Cells (CLC), and peripheral pin select for flexible real-time control. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and a range of peripherals. The PIC18F15Q40 belongs to the 8-bit RISC MCU family, sits within the broader PIC microcontroller hierarchy, and is targeted at real-time control and sensor applications. It uses a modified Harvard architecture with separate program and data buses and a C-compiler-friendly instruction set. Key features include operation across 1.8 V to 5.5 V, ten ADC channels, up to six 16-bit PWM outputs with complementary and dead-band control, CLC for hardware glue logic, and zero-cross detection for TRIAC and motor control. The integrated 32 KB Flash supports self-programming and non-volatile data, and the 2 KB SRAM is sized for small protocol stacks or sensor-fusion loops. The PIC18F15Q40 uses Microchip's latest core revision with single-cycle instruction execution from Flash, hardware multiply, and a C-friendly compiler. The ADCC automates averaging, oversampling, and threshold comparisons, offloading the CPU for filter and sensor conditioning tasks. DMA moves data between peripherals and memory without CPU intervention, freeing cycles for control loops. Typical applications include consumer appliance control, LED lighting drivers, battery-powered sensor nodes, low-cost motor control, and IoT end-node signal conditioning. The combination of 16-bit PWM, CLC, and ADCC reduces BOM cost by replacing external op-amps, timers, and comparators. When designing with this part, derate maximum clock versus Vdd per the datasheet's frequency-voltage graph and keep the MCLR pin configuration within the in-circuit debug (ICD) limits. Select the SO package for hand-solderable prototype builds and the SS (SSOP) variant for high-density production. This page synthesizes distributor pricing, drop-in same-package alternatives from Microchip's PIC18 family, and practical design notes that go beyond the manufacturer datasheet to help procurement and engineering teams shorten sourcing decisions.

RFQ İletişim

PIC18F15Q40-E/SS

PIC18F15Q40-E/SS - 32KB Flash 64MHz 8-bit MCU | Microchip

The Microchip PIC18F15Q40-E/SS is a high-performance 8-bit PIC microcontroller with 32KB Flash, 2KB RAM, and 512 bytes EEPROM, housed in a 20-pin SSOP package. It runs at up to 64MHz and targets real-time control and sensor applications, integrating a 12-bit ADC with Computation (ADCC), two 8-bit DACs, 16-bit PWMs, DMA, Configurable Logic Cells (CLC), and multiple serial interfaces including UART, SPI, and I2C. An 8-bit microcontroller (MCU) is a single-chip computer that uses an 8-bit data bus and is optimized for embedded control tasks. The PIC18 family sits within the broader taxonomy of microcontroller -> RISC processor -> CMOS logic IC -> semiconductor. 8-bit MCUs remain widely used where cost, deterministic interrupt response, and low power outweigh raw compute throughput, particularly in real-time control loops, capacitive touch sensing, motor control, and sensor signal conditioning. Key differentiating features include the 12-bit ADCC that automates Capacitive Voltage Divider (CVD) techniques for advanced touch sensing, on-chip oversampling and threshold comparison for noise-robust measurements, and dual 8-bit DACs that eliminate external analog components in closed-loop control. The Direct Memory Access (DMA) engine moves data between peripherals and memory without CPU intervention, freeing cycles for application logic. Architecturally, the device uses Microchip's enhanced PIC18 RISC core with a hardware multiplier and 16-bit instructions, delivering roughly 16 MIPS at 64MHz. The CLC blocks allow glue-logic functions (AND/OR/XOR gates, flip-flops) to be implemented in silicon rather than in discrete logic, reducing BOM cost and PCB area. Typical applications include capacitive touch user interfaces, BLDC motor control with sensorless FOC, LED lighting controllers, battery management front-ends, and small sensor hubs. The combination of ADCC + CLC + 16-bit PWM makes it particularly suitable for single-chip mixed-signal designs. When designing, pay attention to the SSOP-20 thermal envelope and provide adequate decoupling (100nF + 10uF) close to VDD. The E temperature grade (-40C to +125C) supports automotive and industrial environments. The -E suffix indicates the extended temperature grade; the -I suffix covers -40C to +85C industrial. This page synthesizes distributor pricing, pin-compatible PIC18 alternatives, and practical design notes not found in the manufacturer datasheet alone. Use the comparison table and selection guide to choose the right Q40-family variant for your application.

RFQ İletişim

PIC18F15Q40-I/P

PIC18F15Q40-I/P - 8-Bit 64MHz MCU, 32KB Flash, 20-PDIP | Microchip

The Microchip Technology PIC18F15Q40-I/P is an 8-bit RISC microcontroller from the PIC18-Q40 family, featuring a 64 MHz CPU, 32 KB of Flash program memory, 2 KB of SRAM, and 512 bytes of EEPROM, housed in a 20-pin PDIP through-hole package. According to the Microchip datasheet, it integrates a 12-bit ADC with Computation (ADCC), two 8-bit DAC modules, 16-bit PWMs, Direct Memory Access (DMA), Configurable Logic Cells (CLC), and Peripheral Pin Select (PPS), making it well suited for real-time control and sensor applications. What is a PIC microcontroller? A PIC (Peripheral Interface Controller) is a family of Harvard-architecture microcontrollers from Microchip Technology built around a RISC instruction set, widely used in embedded systems that require deterministic real-time response, low power consumption, and rich peripheral integration. Within the taxonomy, the PIC18F15Q40 sits in the 8-bit PIC18 family -> PIC microcontroller -> microcontroller unit (MCU) -> embedded processor -> semiconductor device. Key features of the PIC18F15Q40-I/P include up to 64 MHz operation, a 12-bit ADCC with automated capacitive voltage divider (CVD) for advanced touch sensing, two 8-bit DACs for analog outputs, DMA for data movement without CPU intervention, four 16-bit PWMs for motor and power control, four CLC blocks for hardware glue logic, and PPS for flexible pin mapping. Its 32 KB Flash and 2 KB SRAM give enough headroom for state-machine plus protocol stacks in compact designs. Technically, the ADCC automates averaging, filtering, oversampling, and threshold comparison, offloading signal-conditioning work that would otherwise consume CPU cycles. DMA channels move ADC results into RAM or PWM registers autonomously, freeing the CPU for closed-loop control. The CLC peripheral implements combinational and sequential logic on-chip, replacing small external logic ICs and reducing BOM cost. PPS allows most digital peripherals to be remapped to a wide range of I/O pins, simplifying PCB layout. Typical applications include capacitive touch user interfaces, BLDC motor control, LED lighting drivers, sensor signal conditioning, HVAC fan control, and small-form-factor IoT edge nodes. The 20-pin PDIP variant is especially attractive for breadboarding, education, and through-hole production where hand-soldering or socketed replacement is required. When designing with this part, leverage the peripheral pin select (PPS) feature to route peripherals to convenient pins, and use the CLC to implement safety logic or hardware interlocks without external gates. Plan for ICD/ICSP header access if in-field firmware updates are required.

RFQ İletişim

PIC18F15Q40-I/REB

PIC18F15Q40-I/REB - 8-Bit 64MHz PIC18 MCU, 32KB Flash | Microchip

The Microchip Technology PIC18F15Q40-I/REB is an 8-bit PIC18 microcontroller running up to 64MHz with 32KB Flash, 2KB SRAM and 512 bytes EEPROM in a compact 20-pin VQFN 3x3 mm package. Built on the PIC18-Q40 family architecture, the device integrates a 12-bit ADC with Computation, 8-bit DACs, 16-bit PWMs, Direct Memory Access (DMA), Configurable Logic Cells (CLC) and communication peripherals suited to real-time control and sensor applications. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program memory (Flash), data memory (RAM), non-volatile storage (EEPROM) and configurable peripherals on a single die. Within the broader taxonomy, the PIC18F15Q40 sits under 8-bit microcontroller -> microcontroller -> integrated circuit -> semiconductor. Microchip's PIC18 family uses a Harvard RISC architecture with a 16-bit instruction word optimized for C-compiled firmware and deterministic interrupt response. Key differentiating features include 12-bit ADC with Computation for hardware-averaged oversampling and analog signal conditioning, 16-bit PWMs with fine resolution for power conversion and motor control, configurable logic cells for glue-less peripheral interconnection, and DMA to offload CPU data movement. The 20-pin VQFN package also enables layout-dense sensor nodes and appliance-grade products. Architecturally, the PIC18F15Q40 combines a high-performance 8-bit core with advanced analog integration. The ADC2 (12-bit with computation) supports hardware accumulation, oversampling and threshold-based triggering, offloading DSP-style filtering from the CPU. CLCs allow combinational/sequential logic to be built from internal peripheral signals without external gates, while DMA channels move data between peripherals and RAM without CPU intervention, critical for high-throughput sensor fusion. Typical applications include sensor signal conditioning nodes, motor control (BLDC and stepper) sub-systems, white-goods and appliance control boards, LED lighting controllers, IoT edge nodes, and small-form-factor power converters. The combination of 12-bit ADC, 16-bit PWM and DMA is particularly suited to digital power and closed-loop control. When designing with this device, allocate analog and digital supply pins separately and place the VQFN-20 EP thermal pad with sufficient copper to meet thermal targets. Verify ICSP programming pin assignments against the datasheet pinout before finalizing the PCB, since the small 3x3 mm footprint leaves limited routing margin. This page synthesizes distributor pricing, drop-in alternatives within the PIC18-Q40 family, and practical design notes not consolidated in the manufacturer datasheet, delivering information gain beyond distributor listings.

RFQ İletişim

PIC18F15Q40-I/SS

PIC18F15Q40-I/SS - 64MHz 8-bit MCU, 32KB Flash, 20-SSOP | Microchip

The Microchip Technology PIC18F15Q40-I/SS is an 8-bit PIC18 microcontroller running up to 64 MHz with 32 KB of Flash, 2 KB of SRAM, and 512 bytes of EEPROM, housed in a 20-pin SSOP package. It is part of the PIC18-Q40 family targeted at real-time control and sensor applications. The device operates from 1.8 V to 5.5 V and provides 18 general-purpose I/O pins. An 8-bit microcontroller is a programmable computing core that executes one byte per internal data path and integrates Flash program memory, SRAM, and peripherals into a single silicon die. The PIC18 family extends Microchip's baseline PIC16 architecture with a 16-bit instruction word, hardware multiplier, linear RAM map, and C-friendly compiler support (XC8), placing it in the MCU hierarchy above PIC10/12/16 and below the 16-bit dsPIC/PIC24 and 32-bit PIC32 lines. PIC18-Q40 specifically targets compact, low-pin-count real-time control designs. Key features of the PIC18F15Q40 include a 12-bit ADC-with-Computation (ADCC) supporting automated Capacitive Voltage Divider (CVD) touch sensing, two 8-bit DACs, two 16-bit PWMs with complementary outputs and center-aligned modes, a Direct Memory Access (DMA) controller, Configurable Logic Cells (CLC) for hardware glue logic, and communication peripherals including UART, SPI, and I2C. The ADCC engine performs oversampling, averaging, and threshold comparisons autonomously, reducing CPU burden. Architecturally, the device combines an 8-bit data path with a 16-bit enhanced Harvard instruction set, 31-level stack, and 49 instructions. Internal 64 MHz oscillator accuracy is +/-1 percent across voltage and temperature. The CIP (Core Independent Peripherals) approach - CLC + DMA + ADCC - allows sensor-processing pipelines to run without waking the CPU, enabling low-power sensor node designs. Typical applications include capacitive touch user interfaces, sensor signal conditioning, LED lighting control, small motor control, IoT end nodes, and battery-powered instrumentation. The combination of ADCC, DAC, and PWM in a 20-pin SSOP suits appliance front panels, white-goods controls, and compact industrial sensor modules. When designing with this MCU, ensure the SSOP-20 footprint accommodates 0.65 mm pitch routing and that the CVD touch sensor trace geometry follows Microchip's mTouch guidelines. Power sequencing is straightforward within the 1.8 V to 5.5 V range, and decoupling per the datasheet (100 nF + 1 uF) should be placed within 3 mm of VDD pins. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes - including DMA and CLC usage patterns - that are not collected in a single location in the manufacturer datasheet.

RFQ İletişim

PIC18F15Q40T-I/SO

PIC18F15Q40T-I/SO - 8-bit 64MHz MCU, 32KB Flash | Microchip

The Microchip PIC18F15Q40T-I/SO is a high-performance 8-bit PIC microcontroller from the PIC18-Q40 family, featuring a 64 MHz CPU core, 32 KB of Flash program memory, 2 KB of SRAM and 512 bytes of EEPROM, housed in a 20-pin SOIC (SO) package. This compact MCU is engineered for real-time control and sensor applications, integrating a 12-bit ADC with Computation (ADCC), two 8-bit DAC modules, up to four 16-bit PWM channels, DMA, Configurable Logic Cells (CLC), and a Peripheral Pin Select (PPS) routing fabric. A PIC18-Q40 microcontroller is a member of the 8-bit PIC18 family from Microchip, which itself sits within the broader category of microcontrollers (MCUs) and ultimately integrated circuits. PIC18-Q40 devices target low-pin-count, real-time signal-chain applications by combining a high-MIPS 8-bit core with sophisticated analog and digital peripherals that previously required external components. The ADCC (ADC-with-Computation) automates capacitive touch sensing (CVD), averaging, filtering, oversampling and threshold comparison, replacing software loops with hardware acceleration. Key differentiating features include ADCC for advanced capacitive touch sensing, two 8-bit DACs for setpoint generation or waveform output, 16-bit PWMs with up to four channels for power-conversion and motor control, integrated DMA for offloading the CPU, PPS for flexible pin mapping, and a CLC block for combinational logic synthesis without external gates. The part operates across 1.8V to 5.5V VDD and supports an industrial temperature range of -40C to +85C. Architecturally, the PIC18F15Q40T-I/SO uses an enhanced Harvard architecture with a 16-bit instruction word and an 8-bit data path, executed by the C-compiler-optimized PIC18 core. The ADCC and CLC blocks reduce firmware burden for touch and logic applications, while DMA enables high-throughput ADC-to-memory transfers without CPU intervention. Typical applications include capacitive touch user interfaces, sensor signal conditioning, low-power motor control, LED lighting control, and compact IoT sensor nodes. The wide 1.8V to 5.5V supply range supports both 3.3V and 5V system rails. When designing with this part, leverage PPS to remap peripherals to any digital I/O pin, which simplifies PCB layout. Ensure adequate decoupling with a 100 nF capacitor on VDD near the package and follow Microchip AN2648 (Capacitive Touch Design) for robust touch-sensing electrode patterns. This page synthesizes current distributor pricing, drop-in alternative MPNs, and practical design notes beyond what is found in the manufacturer datasheet, supporting faster component selection and BOM finalization.

RFQ İletişim

PIC18F15Q41-E/P

PIC18F15Q41-E/P - 8-bit MCU, 32KB Flash, 64MHz, 20-PDIP | Microchip

The Microchip Technology PIC18F15Q41-E/P is an 8-bit RISC microcontroller from the PIC18-Q41 family, featuring a high-performance PIC18 CPU core operating at up to 64 MHz, with 32 KB of Flash program memory, 2 KB of SRAM, and 512 bytes of data EEPROM, housed in a 20-pin PDIP (Plastic DIP) through-hole package. The device operates from 1.8 V to 5.5 V and integrates advanced analog peripherals including an on-chip operational amplifier, 12-bit ADC with Computation (ADCC), an 8-bit DAC, DMA, 16-bit PWM, and Peripheral Pin Select (PPS) for flexible signal routing. A PIC18 microcontroller is an 8-bit Harvard-architecture MCU belonging to the broader category of microcontrollers (MCU) which sit within the integrated circuit (semiconductor) family tree. PIC18 devices use a modified RISC instruction set and are widely used in embedded control, sensor interfacing, and low-power IoT applications where deterministic real-time response and rich analog integration are required. The Q41 sub-family specifically targets sensor and real-time control applications, adding analog peripherals that historically required external components. Key features include 18 general-purpose I/O pins, on-chip op-amp, 12-bit ADCC, 8-bit DAC, 16-bit PWM with complementary outputs, DMA controller for offloading CPU data movement, UART/SPI/I2C communication peripherals, and configurable logic cells. The PPS feature allows digital peripheral pins to be remapped to multiple physical I/O pins, simplifying PCB layout when signal routing conflicts arise. The -E temperature grade supports -40 °C to +125 °C operation, making the part suitable for industrial environments. Architecturally, the PIC18F15Q41 leverages a 16-bit instruction word with an 8-bit data path, hardware multiplier, and a vectored interrupt controller supporting prioritized interrupts. The 64 MHz internal oscillator eliminates the need for an external crystal in many designs, and the device supports multiple low-power sleep modes for battery-powered applications. Typical applications include industrial sensor conditioning, IoT edge nodes, motor control (small DC fans, solenoids), LED lighting controllers, and consumer appliances. The integrated op-amp and 12-bit ADCC are particularly well suited for direct interface to analog sensors (temperature, pressure, light) without external signal conditioning ICs. When designing with this device, ensure that ICSP programming pins (PGC/PGD) and MCLR are accessible for in-circuit programming. A 0.1 µF decoupling capacitor placed within 5 mm of VDD and a 10 µF bulk capacitor are recommended for stable operation across the wide 1.8 V to 5.5 V supply range. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, with cross-brand candidates sourced from third-party parametric databases and verified for same-package pin compatibility.

RFQ İletişim

PIC18F15Q41-E/REB

PIC18F15Q41-E/REB - 8-bit 64MHz MCU, 32KB Flash VQFN-20 | Microchip

The Microchip Technology PIC18F15Q41-E/REB is an 8-bit RISC microcontroller from the PIC18-Q41 family, featuring a high-performance PIC18 CPU core running at up to 64 MHz, 32 KB of Flash program memory, 2 KB of data RAM, and 512 bytes of data EEPROM, all housed in a 20-pin VQFN (3x3 mm) package. It integrates an on-chip operational amplifier, a 12-bit ADC with Computation (ADCC), an 8-bit DAC, a 16-bit PWM module, DMA, and Peripheral Pin Select (PPS), making it well-suited for sensor and real-time control applications. The operating voltage range spans 1.8 V to 5.5 V, with the /REB suffix denoting the VQFN-20 (3x3) package and the /E suffix indicating the extended -40 °C to +125 °C industrial temperature grade. An 8-bit microcontroller (MCU) is a compact programmable processor that integrates a CPU, memory, and peripherals on a single die, designed to deliver deterministic real-time control at low power and cost. PIC18 devices sit between baseline PIC10/12/16 parts and 16-bit dsPIC33 parts in Microchip's 8-bit hierarchy, combining a rich peripheral set with the simplicity of an 8-bit data path. The PIC18F15Q41 belongs to the Q41 sub-family, which adds high-performance analog peripherals (ADCC, DAC, op-amp) and Core Independent Peripherals (CIPs) for offloading CPU work. Key features include 32 KB self-programmable Flash with Flash Partitioning, a 12-bit ADCC supporting up to 17 channels and hardware oversampling, an 8-bit DAC with low-power operation, configurable logic cells, multiple 16-bit PWMs with complementary outputs, and four DMA channels for data movement without CPU intervention. Communication interfaces include two UART, two SPI, and two I2C modules, all remappable via PPS. The architecture is built around an enhanced PIC18 Harvard core with hardware multiply, a 31-level hardware stack, and an interrupt controller with vectored priorities. The ADCC can perform automated averaging and threshold comparisons in hardware, while the op-amp can be used as a PGA or general-purpose amplifier for sensor signal conditioning - both reduce firmware complexity and code size. Typical applications include closed-loop fan control, sensor signal conditioning with analog front-end, LED lighting controllers, low-cost BLDC drivers, battery charging front-ends, and IoT edge sensor nodes. The combination of op-amp, DAC, ADCC, and 16-bit PWM enables a single-chip solution for many closed-loop analog control loops. When designing with this part, ensure the VDDCORE pin is decoupled with a 100 nF + 1 µF pair, the VDD pin uses a 10 µF bulk + 100 nF bypass, and unused I/O pins are configured as outputs low to minimize current draw. For automotive or extended-temperature deployments requiring -40 °C to +125 °C operation, the /E suffix confirms grade suitability. This page synthesizes distributor pricing, pin-compatible alternatives, and practical design notes not found in the standalone manufacturer datasheet.

RFQ İletişim

PIC18F15Q41-E/SO

PIC18F15Q41-E/SO - 32KB Flash 8-bit MCU, 64MHz, 20-SOIC | Microchip

The Microchip Technology PIC18F15Q41-E/SO is a high-performance 8-bit PIC microcontroller from the PIC18-Q41 family with 32KB Flash, 2KB SRAM, and 512B EEPROM in a 20-pin SOIC package. The device runs at up to 64MHz CPU speed, operates from 1.8V to 5.5V, and integrates advanced analog peripherals including a 12-bit ADC, an 8-bit DAC, an on-chip operational amplifier, a 16-bit PWM, and configurable peripherals via Peripheral Pin Select (PPS). It is specifically designed for sensor interfacing and real-time control in compact form-factor applications. An 8-bit microcontroller (MCU) is a programmable integrated circuit that combines a CPU, memory, and peripherals on a single die. The PIC18 family is Microchip's mid-range 8-bit architecture, positioned above PIC16 (baseline) and PIC10/12/14 (low pin-count) families. MCUs form the "brain" of embedded systems, executing firmware to read sensors, drive outputs, and manage communications. The PIC18F15Q41-E/SO is engineered for sensor and real-time control applications, sitting within the broader hierarchy: PIC18-Q41 family -> PIC18F family -> 8-bit MCU -> microcontroller -> embedded IC -> semiconductor. Key features include 32KB self-programmable Flash with 10,000 erase/write cycles, 2KB SRAM, 512B high-endurance EEPROM, and 12-bit differential ADC with computation. The on-chip op-amp eliminates the need for an external amplifier in many sensor signal chains, while the 8-bit DAC enables analog waveform generation. Configurable logic cells and PPS allow flexible pin function remapping, simplifying PCB layout when peripherals must move due to routing constraints. The device supports UART, SPI, and I2C serial communications plus DMA for offloading CPU data transfers. Typical applications include motor control (BLDC, stepper), power supply monitoring and conversion, sensor signal conditioning, LED lighting control, IoT edge nodes, and small medical/industrial devices. The combination of analog integration and PWM channels makes it particularly suited for closed-loop control systems. When designing with this device, evaluate the 20-pin count early - if more I/O is needed, consider the PIC18F16Q41 or PIC18F14Q41 variants in the same package for memory scaling.

RFQ İletişim

PIC18F15Q41-E/SS

PIC18F15Q41-E/SS - 8-bit MCU 32KB Flash 64MHz SSOP-20 | Microchip

The Microchip Technology PIC18F15Q41-E/SS is an 8-bit PIC18 RISC microcontroller running up to 64 MHz with 32 KB of Flash program memory, 2 KB of SRAM and 512 bytes of EEPROM, housed in a 20-pin SSOP package. It integrates advanced analog peripherals including a 12-bit ADC with Computation (ADC2), an 8-bit DAC, on-chip operational amplifiers, a 16-bit PWM module and a high-performance sensor-interface analog fabric aimed at real-time control applications. An 8-bit microcontroller (MCU) is a small, self-contained computer-on-a-chip built around an 8-bit data path. The PIC18 family uses a Harvard RISC architecture with separate program and data buses, 31-level hardware stack, and a rich peripheral set that places digital control logic and analog signal conditioning on the same die. Within the broader semiconductor taxonomy this part belongs to: microcontroller -> 8-bit MCU -> PIC18 -> PIC18-Q41 family -> embedded computing IC. Key features include 32 KB self-programmable Flash with device Information Area (DIA), 2 KB data SRAM with hardware-managed banking, 512 bytes data EEPROM rated for 100k erase/write cycles, a 12-bit ADC2 with up to 17 analog channels, two on-chip operational amplifiers, a 5-bit DAC and an 8-bit DAC, four 16-bit PWM channels with complementary outputs and fine resolution, plus communication peripherals such as UART, SPI and I2C. The device operates from 1.8 V to 5.5 V and supports extended temperature range -40C to +125C. Architecturally the PIC18-Q41 family combines a high-drive 64 MHz core with on-chip op-amps, zero-crossing detect and a configurable logic cell so the MCU can replace many external analog components. This integration simplifies sensor signal chains for thermocouples, RTDs, photodiodes and strain gauges while reducing BOM count and PCB area. Typical applications include IoT sensor nodes, medical wearable monitors, industrial sensor transmitters, LED lighting controllers, low-end motor control, smoke and gas detectors, and consumer white-goods HMI front-ends. The wide voltage range and rich analog make it equally suited to 3.3 V coin-cell designs and 5 V industrial loops. When designing with this part, allocate sufficient decoupling (100 nF + 1 uF) close to VDD/AVDD pins, route the analog reference and Vcap carefully, and respect the programming/debug pin (ICSPCLK/ICSPDAT) sharing to avoid in-circuit programming conflicts. This page synthesizes distributor pricing, drop-in SSOP-20 alternatives and practical design notes not found in the manufacturer datasheet alone.

RFQ İletişim

PIC18F15Q41-I/P

PIC18F15Q41-I/P - 8-bit MCU, 32KB Flash, Op Amp | Microchip

The Microchip Technology PIC18F15Q41-I/P is an 8-bit RISC microcontroller from the PIC18-Q41 family, featuring 32KB of Flash program memory, 2KB of SRAM, and 512 bytes of EEPROM in a 20-pin PDIP through-hole package. It operates at up to 64MHz clock speed with a wide 2.3V to 5.5V supply range and includes a 12-bit ADC with Computation (ADCC), an 8-bit DAC, two op amps, a 16-bit PWM with dual independent outputs, DMA, and Peripheral Pin Select (PPS) for flexible signal routing. What is an 8-bit MCU? An 8-bit microcontroller is a single-chip computer that processes data in 8-bit chunks and integrates a CPU, memory, and peripherals. Within the broader taxonomy, the PIC18F15Q41 belongs to the PIC18 family of enhanced 8-bit microcontrollers, which sit under the PIC microcontrollers family, the microcontroller (MCU) category, and ultimately power management and embedded control semiconductors. PIC18 devices balance low cost, low power, and ease of use, making them a long-standing industry workhorse for sensor and control designs. Key features of this part include integrated analog peripherals (op amps, 12-bit ADCC, 8-bit DAC, comparators, 8-bit voltage reference), Core Independent Peripherals (CIPs) such as CWG, NCO, and PWM, DMA support for offloading CPU data movement, and on-chip debug via single-wire In-Circuit Serial Programming (ICSP). The 16-bit PWM module delivers dual independent outputs on the same time base, ideal for motor control and digital power conversion, while PPS allows nearly any digital peripheral to be mapped to almost any I/O pin. From an architectural standpoint, the PIC18F15Q41-I/P uses a Harvard RISC architecture with an 8-level hardware stack, hardware multiplier, and 31 interrupt sources. The ADCC automates averaging, threshold detection, and burst accumulation, reducing firmware overhead for sensor front-ends. Two on-chip op amps and an 8-bit DAC enable closed-loop analog signal chains without external components. Typical applications include sensor signal conditioning with on-chip op amps, LED lighting and color mixing, low-cost motor control (PWM-driven brushed DC or stepper), battery-powered IoT nodes, capacitive touch user interfaces, and consumer appliance control panels. The wide 2.3V-5.5V operating range simplifies both 3.3V and 5V system designs. When designing with this MCU, ensure that the ICSP programming pins (PGx/RGx) are accessible for field updates and consider using PPS to route peripherals in a way that simplifies PCB routing. For noise-sensitive analog designs, place the part's analog supply (AVDD) as close to a clean, bypassed source as possible. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ İletişim

PIC18F15Q41-I/REB

PIC18F15Q41-I/REB - 8-Bit MCU, 32KB Flash, 20-VQFN | Microchip

The Microchip Technology PIC18F15Q41-I/REB is an 8-bit PIC18 microcontroller with 32KB of Flash program memory, 2KB of SRAM, and 512 bytes of EEPROM, operating at up to 64MHz in a compact 20-pin VQFN (3x3 mm) package. It belongs to the PIC18-Q41 family, which targets sensor interfacing, real-time control, and advanced analog applications where board space is constrained but analog performance cannot be compromised. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, integrating a CPU, non-volatile program memory, volatile data memory, peripherals, and I/O on one silicon die. PIC18-family MCUs from Microchip use a Harvard-architecture RISC core with hardware multiplier, offering deterministic instruction timing, low power consumption, and a mature MPLAB X / MCC toolchain. They sit within the broader category of embedded microcontrollers -> microprocessors -> semiconductors -> integrated circuits. Key differentiating features of the PIC18F15Q41-I/REB include a 12-bit ADC2 with computation, an 8-bit DAC, two on-chip operational amplifiers, a 16-bit PWM, DMA, and Peripheral Pin Select (PPS). The device also integrates two UART, SPI, and I2C peripherals plus a complementary waveform generator (CWG) and numerically controlled oscillator (NCO). These features position the part above general-purpose 8-bit MCUs and adjacent to Microchip's PIC16 family. Architecturally, the PIC18F15Q41 leverages the enhanced mid-range core with a modified Harvard bus, hardware multiply/divide, and vectored interrupts. The advanced analog peripherals - op-amp + 12-bit ADC2 - reduce the bill of materials in sensor-conditioning circuits, while DMA offloads data movement from the CPU. Typical applications include IoT sensor nodes, industrial sensing and control loops, LED lighting drivers, medical instrumentation front-ends, and consumer appliances requiring on-chip analog conditioning in a small 3x3 mm VQFN footprint. When designing with this device, ensure the VQFN-20 (3x3) thermal pad is properly soldered to the PCB ground plane for thermal dissipation and electrical reference. The on-chip op-amp output drives only modest loads - buffer externally if heavy sourcing/sinking is required.

RFQ İletişim

PIC18F15Q41-I/SO

PIC18F15Q41-I/SO - 32KB Flash, 64MHz 8-bit MCU | Microchip

The Microchip Technology PIC18F15Q41-I/SO is an 8-bit PIC18 microcontroller with 32 KB of Flash program memory, 2 KB of SRAM, and 512 bytes of EEPROM, operating at up to 64 MHz and housed in a 20-pin SOIC package. The part integrates an on-chip operational amplifier, a 12-bit differential Analog-to-Digital Converter (ADC2), an 8-bit DAC, 16-bit PWM peripherals, and a configurable logic block, all aimed at sensor and real-time control designs in compact form factors. A PIC microcontroller (often abbreviated MCU) is a programmable logic device that integrates a CPU, memory, and peripherals onto a single die. The PIC18 family sits in the 8-bit MCU category hierarchy between the smaller PIC16 and the higher-end 16-bit dsPIC33 families, with a modified Harvard RISC core optimized for deterministic interrupt response and low-power operation. The Q41 subgroup further specializes PIC18 by adding advanced analog peripherals for sensor-front-end and closed-loop control applications. Key features of the PIC18F15Q41-I/SO include 18 general-purpose I/O pins, a 64 MHz internal oscillator, multi-voltage I/O (MVIO) support down to 1.8 V, a 12-bit ADC with computation engine, two 8-bit DACs, on-chip op-amps for signal conditioning, and configurable logic cells for hardware customization. Core-independent peripherals reduce CPU load for time-critical tasks. The architecture combines a RISC CPU with on-chip debug and a Peripheral Pin Select (PPS) system that maps digital peripherals to any I/O pin, simplifying PCB layout. The device operates over an extended industrial temperature range and offers low-power sleep modes with peripheral wake-up, suitable for battery-powered sensor nodes. Typical applications include IoT sensor nodes, medical wearables, smart lighting controllers, industrial process sensors, and low-end motor control. The combination of integrated op-amps and a 12-bit ADC enables single-chip signal-chain designs for thermistor, RTD, and strain-gauge conditioning. When designing with this MCU, ensure decoupling capacitors are placed close to VDD pins, and follow Microchip's recommended programming/debug header layout for MPLAB PICkit or ICD tool compatibility. PPS remapping must be configured before peripheral use to avoid unexpected pin states during bring-up. This page synthesizes verified distributor pricing, curated cross-reference alternatives within the same package, and application notes not aggregated in the Microchip datasheet - offering clear engineering guidance for new designs.

RFQ İletişim

PIC18F15Q41-I/SS

PIC18F15Q41-I/SS - 8-Bit MCU, 64MHz, 32KB Flash | Microchip

The Microchip Technology PIC18F15Q41-I/SS is an 8-bit PIC18 microcontroller delivering 64 MHz CPU performance with 32 KB Flash, 2 KB SRAM, and 512 bytes EEPROM, housed in a 20-pin SSOP package. The Q41 family integrates advanced analog peripherals - including a 12-bit ADC with computation, two 8-bit DACs, an on-chip operational amplifier, and 16-bit PWM - that target sensor and real-time control applications. What is a PIC18 microcontroller? The PIC18 is Microchip's high-performance 8-bit MCU family built on a modified Harvard architecture with a C-optimized instruction set. PIC18 microcontrollers belong to the broader category of microcontrollers (MCUs), which sit inside the integrated circuit (IC) hierarchy along with memory, analog, and interface ICs. Within an embedded system, an MCU provides the central processing, memory, and peripheral integration that replaces discrete logic and analog chains, making the PIC18F15Q41 a single-chip solution for compact sensor/control nodes. Key features include a wide 1.8V to 5.5V operating voltage range, 18 general-purpose I/O pins, hardware UART/SPI/I2C, configurable logic cells, and zero-crossing detection. The device operates across -40 C to +85 C (industrial) and supports in-circuit serial programming (ICSP) plus on-chip debugging. An integrated temperature indicator and 5-bit DAC simplify closed-loop designs. The Q41 architecture combines a 16-bit instruction path with 8-bit data paths and a hardware multiplier, enabling efficient DSP-style filtering on the ADC channel. The 12-bit ADC with accumulation and averaging automates sensor linearization, while the complementary waveform generator produces complementary, dead-band-controlled PWM for power-conversion and motor-drive stages. Typical applications include IoT sensor nodes, LED lighting controllers, medical monitoring peripherals, industrial sensing, capacitive-touch human interfaces, and low-power fan/HVAC control. The combination of analog integration and small SSOP-20 footprint enables shrinking analog front-end designs into compact PCBs. When designing with this MCU, ensure the supply decoupling network uses a 100 nF ceramic capacitor directly on VDD plus a bulk capacitor on the analog rail. Review the configuration word settings early in firmware development since incorrect oscillator or watchdog settings are the most common bring-up pitfalls. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Pinout, parametric differences, and same-package alternatives are consolidated for engineers evaluating the PIC18F15Q41-I/SS against PIC18F14Q41 and PIC18F05Q41 family members.

RFQ İletişim

PIC18F15Q41T-I/SO

PIC18F15Q41T-I/SO - 32KB Flash 8-bit MCU, 64MHz | Microchip

The Microchip Technology PIC18F15Q41T-I/SO is a high-performance 8-bit PIC18 microcontroller IC featuring 64 MHz CPU speed, 32 KB (32K x 8) FLASH program memory, 2 KB RAM, and 512 bytes of EEPROM, housed in a 20-pin SOIC package. It integrates advanced analog peripherals including a 12-bit ADC with Computation (ADCC), an 8-bit DAC, an on-chip operational amplifier, and a 16-bit PWM module designed for sensor and real-time control applications. A PIC microcontroller (MCU) is a compact, low-power, programmable integrated circuit combining a CPU, memory (Flash/RAM/EEPROM), and peripherals on a single die. Within the broader taxonomy it belongs to the 8-bit MCU class, which sits below 16-bit dsPIC and 32-bit ARM Cortex-M devices in performance and above discrete logic in integration. PIC MCUs typically use a RISC Harvard architecture with separate program and data buses, executing one instruction per clock cycle (excluding branches), giving predictable timing for embedded control loops. Key differentiating features include Direct Memory Access (DMA), Peripheral Pin Select (PPS) for flexible I/O mapping, and zero-crossing detection hardware that simplifies AC line-sensing designs. Communication interfaces include UART, SPI, and I2C, while the integrated op-amp eliminates external analog front-end components for many sensor-conditioning circuits. Typical applications span consumer white goods, LED lighting controllers, battery-powered IoT sensor nodes, motor control for small DC fans and pumps, and touch/proximity user interfaces. The wide 1.8V to 5.5V operating range makes it suitable for both 3.3V and 5V systems directly without level shifters. When designing with this part, ensure the high-temperature operating range (-40C to +85C for the -I grade) is observed for industrial enclosures, and use the PPS feature to remap peripheral functions to free I/O pins when adding functions late in the design cycle. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ İletişim

PIC18F15Q41T-I/SS

PIC18F15Q41T-I/SS - 32KB Flash 8-bit MCU w/ Op Amp | Microchip

The Microchip Technology PIC18F15Q41T-I/SS is an 8-bit PIC18 microcontroller with 32KB Flash, 2KB SRAM, and 512 bytes EEPROM, running up to 64 MHz in a 20-pin SSOP package. The 'T' suffix indicates Tape & Reel packaging, 'I' is the industrial -40C to +85C temperature grade, and 'SS' denotes the 5.30 mm body 20-pin SSOP. This part is part of the PIC18-Q41 family, which integrates advanced analog peripherals including an on-chip operational amplifier, 12-bit ADC2, 8-bit DAC, 16-bit PWM, DMA, and Peripheral Pin Select (PPS) for sensor and real-time control applications. An 8-bit microcontroller (MCU) is a programmable integrated circuit that executes instructions from on-chip Flash memory using an 8-bit data path. PIC18 devices sit in Microchip's mid-range 8-bit portfolio above baseline PIC10/12/16 parts, supporting self-programming, larger RAM/Flash, C-compiler friendly architecture, and richer peripherals. The PIC18-Q41 family extends this with high-performance analog and digital peripherals targeted at sensor signal conditioning and closed-loop control. Key features include 32 KB self-programmable Flash, 2 KB SRAM, 512 bytes EEPROM, 12-bit ADC with computation (ADC2), 8-bit DAC, two operational amplifiers, 16-bit PWM with complementary outputs, DMA controller, and Peripheral Pin Select. The device supports UART, SPI, I2C, and runs instruction cycles at 64 MHz (16 MIPS). The integrated op-amp lets designers implement gain stages, transimpedance amplifiers, and comparators without external analog ICs. Architecturally, the PIC18F15Q41 uses Microchip's enhanced Harvard architecture with 16-bit opcodes and an 8-bit data path, plus hardware multiplier and priority interrupt controller. The ADC2 integrates oversampling, accumulation, and filtering hardware to reduce CPU overhead for sensor averaging. PPS remaps digital peripherals to any I/O pin, simplifying PCB layout. The 20-pin SSOP supports up to 17 I/O pins, leaving room for system expansion. Typical applications include industrial sensor signal conditioning, closed-loop fan/PWM control, LED lighting drivers, battery-powered IoT nodes, USB-to-UART bridges, and small motor control. The industrial temperature range suits factory automation and outdoor equipment. On-chip analog blocks reduce BOM cost for sensor-interface designs where a separate op-amp IC would otherwise be required. Design consideration: leverage the integrated op-amp and DAC for sensor biasing and offset cancellation rather than allocating PCB area to a discrete analog front-end. The DMA engine can move ADC samples to RAM without CPU intervention, freeing cycles for communication stacks. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes drawn from the PIC18-Q41 family datasheet and reference designs - material not collected on a single distributor product page.

RFQ İletişim

Alt Kategoriler

Ürünler (39.000+)

PIC18F14Q41-E/REB - 8-bit 64MHz MCU, 16KB Flash, 20-VQFN | Microchip

PIC18F14Q41-E/SO - 8-Bit 64MHz 16KB Flash MCU | Microchip

PIC18F14Q41-I/P - 8-bit MCU, 16KB Flash, 64MHz, 20-PDIP | Microchip

PIC18F14Q41-I/SO - 8-bit 64MHz MCU 16KB Flash 20-SOIC | Microchip

PIC18F14Q41-I/SS - 8-bit 64MHz 16KB Flash MCU | Microchip

PIC18F14Q41T-I/SO - 8-bit 64MHz 16KB Flash MCU | Microchip

PIC18F15Q40-E/P - 8-bit 64MHz 32KB Flash MCU | Microchip

PIC18F15Q40-E/REB - 8-Bit 64MHz MCU, 32KB Flash, 20-VQFN | Microchip

PIC18F15Q40-E/SO - 8-Bit 64MHz MCU, 32KB Flash 20-SOIC | Microchip

PIC18F15Q40-E/SS - 32KB Flash 64MHz 8-bit MCU | Microchip

PIC18F15Q40-I/P - 8-Bit 64MHz MCU, 32KB Flash, 20-PDIP | Microchip

PIC18F15Q40-I/REB - 8-Bit 64MHz PIC18 MCU, 32KB Flash | Microchip

PIC18F15Q40-I/SS - 64MHz 8-bit MCU, 32KB Flash, 20-SSOP | Microchip

PIC18F15Q40T-I/SO - 8-bit 64MHz MCU, 32KB Flash | Microchip

PIC18F15Q41-E/P - 8-bit MCU, 32KB Flash, 64MHz, 20-PDIP | Microchip

PIC18F15Q41-E/REB - 8-bit 64MHz MCU, 32KB Flash VQFN-20 | Microchip

PIC18F15Q41-E/SO - 32KB Flash 8-bit MCU, 64MHz, 20-SOIC | Microchip

PIC18F15Q41-E/SS - 8-bit MCU 32KB Flash 64MHz SSOP-20 | Microchip

PIC18F15Q41-I/P - 8-bit MCU, 32KB Flash, Op Amp | Microchip

PIC18F15Q41-I/REB - 8-Bit MCU, 32KB Flash, 20-VQFN | Microchip

PIC18F15Q41-I/SO - 32KB Flash, 64MHz 8-bit MCU | Microchip

PIC18F15Q41-I/SS - 8-Bit MCU, 64MHz, 32KB Flash | Microchip

PIC18F15Q41T-I/SO - 32KB Flash 8-bit MCU, 64MHz | Microchip

PIC18F15Q41T-I/SS - 32KB Flash 8-bit MCU w/ Op Amp | Microchip