Ürünler (46.000+)

SN74HC86N - Quad 2-Input XOR Gate, 14-PDIP | Texas Instruments
SN74HC86N

SN74HC86N - Quad 2-Input XOR Gate, 14-PDIP | Texas Instruments

The Texas Instruments SN74HC86N is a quadruple 2-input Exclusive-OR (XOR) gate belonging to the broad 74HC high-speed CMOS logic family, supplied in a 14-pin PDIP (N) through-hole package. It integrates four independent 2-input XOR gates on a single die, each performing the Boolean function Y = A XOR B in positive logic, with a typical quiescent current in the microampere range and 5.2 mA balanced output drive strength. Operating from a 2 V to 6 V VCC supply, it delivers CMOS-level low-power consumption with TTL-compatible input thresholds. An XOR gate is a fundamental combinational logic primitive that outputs a HIGH whenever its two inputs differ. In digital system hierarchies, XOR gates sit alongside AND, OR, and NOT gates as building blocks of arithmetic logic units, parity generators, comparators, and crypto primitives. The 74HC86 places four such gates in one package, reducing board area and interconnect length for glue logic. Key features of the SN74HC86N include ±5.2 mA output drive, wide 2 V to 6 V supply range, low input current of ±1 µA, typical propagation delay around 13 ns at 5 V/15 pF, and ±20 µA quiescent supply current. Its CMOS outputs produce rail-to-rail logic swings, simplifying interfacing with downstream CMOS loads. The HC family is pin-compatible with the LS TTL legacy while consuming a fraction of the power. Architecturally, the SN74HC86 uses a CMOS NAND/NOR-equivalent XOR topology realized with complementary pull-up and pull-down networks. The high-speed CMOS process delivers sub-15 ns gate delay at 5 V while keeping static dissipation negligible. Inputs are CMOS with Schmitt-trigger-like hysteresis improving noise immunity in noisy industrial environments. Typical applications include parity generation and checking in memory and communication systems, half-adder and full-adder construction, controlled inverters, programmable logic replacement, and signal conditioning for comparators. Designers also use XOR gates for phase detectors in PLLs, simple encryption/decryption stages, and switch-debounce or edge-detection circuits. When designing with the SN74HC86N, observe standard CMOS handling rules: tie unused inputs to VCC or GND through a resistor to prevent floating inputs that draw shoot-through current. The 14-PDIP package is suitable for breadboards, prototypes, and legacy through-hole assemblies where surface-mount land patterns are not desired. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a decision-ready snapshot of the SN74HC86N.

RFQ İletişim
SN74HC86NE4 - Quad 2-Input XOR Gate, 14-PDIP | Texas Instruments
SN74HC86NE4

SN74HC86NE4 - Quad 2-Input XOR Gate, 14-PDIP | Texas Instruments

The Texas Instruments SN74HC86NE4 is a quadruple 2-input Exclusive-OR (XOR) gate IC fabricated in high-speed CMOS silicon-gate technology, providing four independent XOR gates in a 14-pin PDIP (plastic DIP) through-hole package. Each of the four gates performs the Boolean function Y = A XOR B in positive logic, with buffered outputs capable of driving 10 LSTTL loads and a wide 2 V to 6 V operating voltage range. The 'NE4' suffix indicates a Pb-free, RoHS-compliant assembly variant of the SN74HC86N, identical electrically but compliant with contemporary lead-free soldering and environmental standards. The device typically exhibits 6 ns propagation delay at 5 V C_load = 50 pF, 5.2 mA output drive strength, and a ±20 µA input leakage at 6 V, suiting it for bus-oriented digital logic designs. What is an XOR gate? An XOR (Exclusive-OR) gate is a fundamental two-input digital logic primitive whose output is HIGH only when the two inputs differ. Positioned within the broader gates-and-inverters IC category, XOR gates sit alongside AND, OR, NAND, NOR, and INVERTER cells, and are widely deployed in parity generators, comparators, half adders, controlled inverters, and arithmetic logic units. A single HC86 device packs four independent XOR gates into one 14-pin package, saving board area and reducing part count versus discrete implementations. Key features include balanced CMOS outputs, low input current of ±1 µA maximum, significant power-reduction versus LSTTL equivalents, and an operating temperature range of -40 °C to +85 °C suitable for industrial applications. The HC family also provides high noise immunity (typically 30% of V_CC as the noise margin) and supports fan-out to 10 LSTTL loads, simplifying interface to legacy bipolar logic without level shifters. Clamp diodes on the inputs allow voltages up to 1.5 V above V_CC without damage. Architecturally, the SN74HC86NE4 uses a silicon-gate CMOS process to deliver HCMOS-equivalent speed at one-fifth the static power of LSTTL. Its TTL-compatible input thresholds (V_IL ≈ 0.9 V at 5 V, V_IH ≈ 3.15 V) allow direct interfacing with legacy bipolar logic without external pull-ups. The four gates are partitioned symmetrically as 1A/1Y, 2A/2Y, 3A/3Y, 4A/4Y to ease PCB routing, and an internal thermal-shutdown feature is absent (CMOS logic is inherently current-limited by design). Typical applications include parity generation and checking in data communication busses, half and full adder construction for low-bit arithmetic, true/complement control logic for op-amp switching, phase-detector networks in PLL synthesizers, and address decoders in memory systems. Designers also use the HC86 for binary-to-Gray code conversion, which is essential in optical encoders and shaft position decoding. When designing with this part, ensure unused inputs are tied to V_CC or GND through 1 kΩ pull-down/up resistors rather than left floating to prevent excess current and propagation of noise through the CMOS input stages. Operating above 6 V will damage the device; operating below 2 V disables the internal logic thresholds and produces undefined outputs. This page synthesizes current distributor pricing, AEO-optimized FAQ entries, verified drop-in alternatives, and practical design notes that extend the manufacturer datasheet with engineering-grade decision support.

RFQ İletişim
SN74HCS126QPWRQ1 - Automotive Quad 3-State Buffer | TI
SN74HCS126QPWRQ1

SN74HCS126QPWRQ1 - Automotive Quad 3-State Buffer | TI

The Texas Instruments SN74HCS126QPWRQ1 is an AEC-Q100 qualified automotive quadruple bus buffer with 3-state outputs and Schmitt-trigger inputs, housed in a 14-pin TSSOP (PW) package rated from -40C to +125C. The device operates from a 2.0 V to 6.0 V supply and buffers four non-inverting 1-bit channels with active-high output-enable pins. A CMOS logic buffer is a digital building block that reproduces (non-inverting) a digital signal while providing isolation between a weak or noisy source and a heavier load. In the logic hierarchy, the SN74HCS126-Q1 belongs to the buffer / line driver family of the HC/HCS CMOS logic category, and bus buffers with 3-state outputs further add the ability to disconnect the output from the bus, enabling shared, multidrop data lines in microprocessor and automotive in-vehicle networking systems. Key differentiating features include Schmitt-trigger inputs with hysteresis that convert slow or noisy input transitions into clean, fast edges - essential in automotive environments with ground bounce and EMI; 3-state outputs that implement high-impedance bus sharing; low input hysteresis threshold spread across the 2.0 V to 6.0 V operating range; and a typical CMOS microamp-level quiescent current that minimizes system standby power. The device is qualified per AEC-Q100 Grade 1 for harsh automotive ambient temperatures. Technically, the HCS family combines high-voltage CMOS fabrication with input hysteresis, providing robust switching thresholds (VT+ / VT- spread) across supply voltage, temperature, and process corners. Output drive is balanced across the supply range, and outputs are disabled to high impedance whenever the OE pin is low, allowing multiple drivers on one bus with tri-state control. Power-up and power-down protection prevents bus contention during supply sequencing. Typical applications include automotive body electronics, CAN/LIN transceiver front-end buffering, level-shifted control signals in 12 V-derived rails, industrial PLC I/O, and generic bus-buffering between microcontrollers and peripheral modules where slow edges must be squared up. Design tip: do not let the OE pin float - tie unused enables to ground and unused inputs to VCC or GND; ensure each enabled output sources/sinks within the drive limits at the given VCC to keep VOL/VOH within datasheet margins. This page adds value beyond the manufacturer datasheet by synthesizing distributor pricing, drop-in same-footprint alternatives (HC126 variants, HCS125 siblings), and practical design notes in one place.

RFQ İletişim
SN74HCS541PWR - Octal Buffer Schmitt 3-State TSSOP-20 | TI
SN74HCS541PWR

SN74HCS541PWR - Octal Buffer Schmitt 3-State TSSOP-20 | TI

The Texas Instruments SN74HCS541PWR is an octal buffer and line driver with Schmitt-trigger inputs, 3-state outputs, and a flow-through pinout, supplied in a 20-pin TSSOP (PW) package. It operates over a wide 2 V to 6 V supply range and is fully specified from -40C to +125C. What is an octal buffer/line driver? It is a digital logic IC providing eight independent buffer channels capable of driving bus lines or long PCB traces. The 3-state outputs allow each device to release the bus into a high-impedance state, enabling multi-device bus sharing, while Schmitt-trigger inputs add hysteresis that converts slow or noisy input edges into clean logic transitions. The SN74HCS541 belongs to the HCS (High-speed CMOS with Schmitt-trigger) logic family, combining CMOS low power with TTL-compatible drive. Key features include the 2 V to 6 V operating range for 3.3 V and 5 V mixed-voltage systems, typical 0.4 V input hysteresis at 4.5 V for superior noise immunity, dual active-low output enables (OE1 and OE2, both must be low to activate outputs), and only 20 uA typical quiescent current at 6 V. Outputs sink or source up to 6 mA at 4.5 V, suitable for driving LEDs, relays, or additional logic inputs. Fabricated in silicon-gate CMOS, the device balances switching speed with low power dissipation. The flow-through pinout places inputs on one side and outputs on the opposite side, simplifying PCB routing and reducing crosstalk in bus-oriented layouts. Typical applications include microcontroller bus buffering, memory address/data line driving, sensor signal conditioning, and interfacing 3.3 V logic to 5 V domains in industrial automation and automotive-adjacent systems. Design tip: control the OE pins carefully to avoid bus contention, place 0.1 uF decoupling capacitors close to VCC/GND, and keep input rise times below 500 ns at 2 V and 200 ns at 6 V for best performance.

RFQ İletişim
SN74HCS541QPWRQ1 - AEC-Q100 Octal Buffer 3-State | TI
SN74HCS541QPWRQ1

SN74HCS541QPWRQ1 - AEC-Q100 Octal Buffer 3-State | TI

The Texas Instruments SN74HCS541QPWRQ1 is an automotive-qualified (AEC-Q100) octal buffer and line driver featuring eight non-inverting channels with 3-state outputs, Schmitt-trigger inputs, and a flow-through pinout, supplied in a 20-pin TSSOP (PW) package rated from -40C to +125C. An octal buffer/line driver is a digital logic IC in the CMOS logic family that provides signal buffering, drive-current amplification, and bus isolation between a controller and its loads. Within the logic hierarchy, it belongs to the buffer and line-driver category of specialty logic, sitting between simple gates and full bus transceivers. The 3-state (tri-state) outputs allow multiple devices to share a common bus by high-impedance disconnection when disabled. Key features include Schmitt-trigger inputs with hysteresis that tolerate slow or noisy input edges typical of automotive harnesses, wide VCC operation of the HCS Schmitt-CMOS family, two independent active-low output-enable pins (OE1 and OE2) for flexible bus control, and a flow-through pinout that simplifies PCB routing by keeping inputs on one side and outputs on the other. The Q1 grade ensures AEC-Q100 qualification and PPAP support for automotive designs. The HCS (HC with Schmitt input) architecture combines high-speed CMOS output drive with hysteresis-enhanced input stages, improving noise margin on long or filtered signal lines. Outputs are non-inverting, so logic polarity is preserved, making the device suitable for address and control bus buffering in MCU-based systems. Typical applications include automotive body electronics and ADAS control modules, buffering GPIO or SPI/control lines from MCUs such as the TMS320F2800xx series, industrial PLC I/O isolation, and level-tolerant interfacing to switches and sensors with slow edge rates. Design tip: tie both OE pins low for always-enabled operation, and keep VCC decoupling (100 nF ceramic) close to the supply pins; the Schmitt inputs allow RC-filtered inputs but do not eliminate the need for controlled signal routing.

RFQ İletişim
SN74HCS86PWR - Quad 2-Input XOR Schmitt-Trigger Gate | TI
SN74HCS86PWR

SN74HCS86PWR - Quad 2-Input XOR Schmitt-Trigger Gate | TI

The Texas Instruments SN74HCS86PWR is a quadruple 2-input XOR (exclusive OR) gate with Schmitt-trigger inputs, supplied in a 14-pin TSSOP (PW) surface-mount package. It operates from a 2V to 6V supply and is fully specified from -40C to +125C for industrial environments. A logic gate is the fundamental building block of digital electronics, performing Boolean operations on binary inputs. The XOR gate outputs a high level only when an odd number of its inputs is high, making it essential for adders, parity generators and checkers, comparators, and programmable inverters. The SN74HCS86 belongs to the TI HCS family, which pairs CMOS low static power with Schmitt-trigger inputs for superior noise immunity - a drop-in upgrade path for the classic 74HC86. Key features include the wide 2V to 6V operating range, Schmitt-trigger inputs with hysteresis (typically around 0.5V at a 5V supply), CMOS technology for near-zero quiescent current, and balanced output drive. Per the TI datasheet, the device can drive loads up to 50 pF while meeting all datasheet specifications; larger capacitive loads are not recommended. Technically, the CMOS architecture provides high noise margins and negligible static current, while the Schmitt inputs use internal positive feedback to create hysteresis. This makes the part tolerant of inputs from mechanical switches, quadrature encoders, RC oscillators, and long wires with slow rise times - conditions that would cause a standard HC86 input to oscillate or multi-trigger. Typical applications include signal conditioning of noisy sensor or switch inputs, parity generation in serial communication links, crystal and RC oscillator circuits, frequency doubling (XOR with a delayed copy of itself), and digital comparator functions in industrial control, instrumentation, and automotive modules. Design tip: tie all unused inputs to a defined logic level (GND or VCC) to prevent floating nodes, and keep total capacitive load per output at or below 50 pF; add a buffer such as SN74LVC244A if heavier loads are required. Pricing references below are as of 2026-08-30.

RFQ İletişim
SN74HCS86QPWRQ1 - Quad 2-Input XOR Gate, AEC-Q100 | TI
SN74HCS86QPWRQ1

SN74HCS86QPWRQ1 - Quad 2-Input XOR Gate, AEC-Q100 | TI

The Texas Instruments SN74HCS86QPWRQ1 is an automotive-qualified quadruple 2-input XOR (exclusive OR) gate with Schmitt-trigger inputs, supplied in a 14-pin TSSOP (PW) package. It operates from a wide 2 V to 6 V supply range and across a -40C to +125C ambient temperature range, per AEC-Q100 temperature grade 1 qualification. An XOR gate is a fundamental digital logic primitive in the combinational logic family of gates and inverters: its output is HIGH only when an odd number of inputs is HIGH, making it essential for adders, parity generation and checking, pseudo-random sequence generation, and signal comparison. The SN74HCS86-Q1 belongs to the HCS (HC with Schmitt) CMOS logic family, a modern low-power derivative of the classic 74HC high-speed CMOS series. The key feature distinguishing this device is its Schmitt-trigger inputs, which tolerate slow or noisy input edges that would cause oscillation in standard CMOS gates. The wide 2 V to 6 V operating range supports legacy 5 V systems as well as 3.3 V and lower-voltage rails. The device offers very low static power consumption typical of CMOS logic, and automotive-grade robustness with HBM ESD Level 2 and CDM ESD classification Level C6 per the TI datasheet (Rev. C). Because all four XOR gates are independent in a single package, the device consolidates parity trees, phase comparators, and code-comparison functions efficiently on board. Balanced drive capability and standardized TTL/CMOS-compatible thresholds at 5 V ease interfacing with microcontrollers and FPGAs. Typical applications include automotive body and powertrain modules, gate drivers for isolated communication schemes, parity checkers in serial links, frequency doublers, and XOR-based CRC generation in industrial systems. Design tip: keep unused inputs tied to VCC or GND (unused XOR gates may have inputs grounded) to prevent floating-node oscillation and excess current draw, and provide local 100 nF decoupling per TI logic application guidance.

RFQ İletişim
SN74HCT240PWR - Octal Inverting 3-State Buffer | TI TSSOP-20
SN74HCT240PWR

SN74HCT240PWR - Octal Inverting 3-State Buffer | TI TSSOP-20

The Texas Instruments SN74HCT240PWR is an octal inverting buffer and line driver with 3-state outputs, organized as 2 elements of 4 bits each, housed in a 20-pin TSSOP (PW) package. It operates from a 4.5 V to 5.5 V VCC supply, features TTL-compatible CMOS inputs, and provides high-current outputs capable of driving up to 15 LSTTL loads. A buffer and line driver is a digital logic device that amplifies and isolates a signal between a source and a load. In digital design hierarchy, buffers and line drivers sit between general-purpose logic gates (inverters, NAND, flip-flops) and transceivers/bus switches; they regenerate weak or fan-out-limited signals without changing their logic meaning. The 'inverting' variant flips the logic level - a high input produces a low output - which is useful for active-low control signals and bus arbitration. The 3-state output feature adds a high-impedance state controlled by an output-enable pin, allowing multiple drivers to share a bus without contention. Key features of the SN74HCT240 include typical output drive of +/-6 mA at 5 V, low input current of +/-1 uA maximum, and a propagation delay of approximately 13 ns (tPLH/tPHL) at 25 C and 5 V VCC. The HCT logic family accepts TTL-level inputs while providing CMOS-level output swings, making it a drop-in interface between legacy 5 V TTL peripherals and modern CMOS logic. Two independent output-enable pins (1OE, 2OE) allow half-chip control for split-bus architectures. Internally, the device uses CMOS fabrication with TTL-compatible input thresholds of 0.8 V (VIL) and 2.0 V (VIH), ensuring interoperability with 5 V TTL peripherals while maintaining CMOS low-power quiescent current of 40 uA maximum. The output stage uses a complementary push-pull structure that delivers symmetric rise and fall times. Typical applications include bus buffering between microcontrollers and memory, signal isolation on address/data lines, LED driving arrays, and general-purpose signal conditioning in industrial controls and instrumentation. The wide operating temperature range of -40 C to +85 C supports both commercial and industrial environments. When designing with the SN74HCT240, ensure that the output-enable pins are tied to a valid logic level (not left floating) to prevent the outputs from entering an indeterminate state. For high-speed buses, place a 0.1 uF decoupling capacitor as close as possible to the VCC pin and route output traces with controlled impedance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on a single manufacturer or distributor page - including same-brand SN74HCT244PWR (non-inverting variant) and cross-brand equivalents from onsemi (MC74HCT240ADTR2G) and NXP, enabling engineers to evaluate substitutes quickly.

RFQ İletişim
SN74HCT245NSR - Octal Bus Transceiver 3-State | Texas Instruments
SN74HCT245NSR

SN74HCT245NSR - Octal Bus Transceiver 3-State | Texas Instruments

The Texas Instruments SN74HCT245NSR is an octal bus transceiver with 3-state outputs designed for asynchronous two-way communication between data buses, housed in a 20-pin SOP (NS) surface-mount package. It operates from a 4.5V to 5.5V supply, delivers ±6mA output drive at 5V, and features a typical propagation delay of 14 ns. An octal bus transceiver is a digital logic integrated circuit that buffers and transfers eight bits of data between two buses in either direction. As a member of the broader voltage-level-translation and buffer/driver family within the 74HCT high-speed CMOS-TTL-compatible logic series, it sits between bus masters (such as microcontrollers or FPGAs) and peripheral buses, providing drive strength, direction control, and high-impedance isolation. Key features include an operating voltage range of 4.5V to 5.5V, high-current 3-state outputs that can drive bus lines directly or up to 15 LSTTL loads, and low power consumption with a maximum ICC of 80 uA. The device provides ±6mA output drive at 5V and a low input current of 1 uA maximum. Inputs are TTL-voltage compatible, allowing direct interfacing with 5V TTL logic and many 3.3V microcontroller outputs. Architecturally, the SN74HCT245 uses a non-inverting 8-bit transceiver core with two control pins: DIR (direction) selects the data path (A-to-B or B-to-A), and OE (output enable) active-low pin places all outputs in the high-impedance 3-state condition. The HCT CMOS process combines the low static power of CMOS with TTL input thresholds, minimizing external timing requirements per the TI datasheet. Typical applications include microprocessor and MCU peripheral bus isolation, memory and I/O expansion buses, backplane communication in industrial controllers, and 5V legacy system interfacing where TTL-compatible inputs are required. For reliable operation, tie OE low through a pull-down resistor when unused, and place 0.1uF decoupling capacitors close to the VCC pin on both sides of the wide-body package. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not consolidated in the manufacturer datasheet.

RFQ İletişim
SN74HCT74 - Dual D-Type Flip-Flop with Clear/Preset | TI
SN74HCT74

SN74HCT74 - Dual D-Type Flip-Flop with Clear/Preset | TI

The SN74HCT74 is a dual D-type positive-edge-triggered flip-flop from Texas Instruments, featuring clear and preset inputs. It operates over a supply voltage range of 4.5V to 5.5V, making it compatible with TTL logic levels. The device is available in multiple package options including 14-pin DIP (N), SOIC (D), and TSSOP (PW), with the SN74HCT74N being a common through-hole variant. A D-type flip-flop is a fundamental sequential logic element that stores one bit of data. On the rising edge of the clock signal, the output (Q) takes the value of the data input (D). The SN74HCT74 contains two independent flip-flops, each with preset (PRE) and clear (CLR) inputs that asynchronously set or reset the outputs regardless of clock state. This makes it essential for building registers, counters, and state machines in digital systems. Key features include a wide operating voltage range of 4.5V to 5.5V, low power consumption with a maximum ICC of 40 µA, and the ability to drive up to 10 LSTTL loads. The typical propagation delay (tpd) is 15 ns at 5V, and the output drive capability is ±4 mA. The device is fully specified for operation from -40°C to 85°C, making it suitable for industrial applications. The SN74HCT74 uses HCT (High-Speed CMOS with TTL-compatible inputs) technology, which combines the low power of CMOS with the input thresholds of TTL. This allows direct interfacing with TTL logic without additional level shifting. The positive-edge-triggered design ensures reliable data capture, and the asynchronous preset and clear inputs provide flexible control for initialization and reset operations. Typical applications include data storage registers, frequency dividers, and control logic in microcontrollers, industrial automation, and consumer electronics. The device is also used in debouncing circuits and as a building block for more complex sequential logic. Its TTL compatibility makes it ideal for mixed-voltage systems. When designing with the SN74HCT74, ensure that the setup and hold times are met relative to the clock edge. The preset and clear inputs are active-low and should be tied high when unused. Decouple the power supply with a 0.1 µF capacitor near the VCC pin to minimize noise.

RFQ İletişim
SN74LS07D - Hex Buffer/Driver OC 30V 40mA | Texas Instruments (Tape & Reel)
SN74LS07D

SN74LS07D - Hex Buffer/Driver OC 30V 40mA | Texas Instruments (Tape & Reel)

The Texas Instruments SN74LS07D is a hex non-inverting buffer and driver featuring high-voltage open-collector outputs rated at 30 V with a maximum sink current of 40 mA, supplied in a 14-pin SOIC (D) package. Operating from a 4.75 V to 5.25 V TTL supply over a 0 C to 70 C commercial temperature range, it performs level translation and high-current load driving in a single low-cost IC. A buffer/driver is a logic element that isolates and amplifies digital signals so a low-power logic output can drive heavier loads, longer buses, or circuits operating at different voltage levels. Buffers and drivers sit within the broader hierarchy of logic ICs, which spans gates, flip-flops, registers, and bus interface devices in standard 7400 TTL and CMOS families. Key features include open-collector outputs that interface directly with high-level circuits such as MOS gates, indicator lamps, and relays; a strong 40 mA sink-current capability well beyond standard TTL outputs; input clamping diodes that simplify system design by suppressing negative-going line transients; and operation as a straight-through non-inverting buffer for driving TTL inputs. These characteristics make it a classic choice for logic-to-power interfacing. Architecturally, the SN74LS07 is a bipolar LS-TTL device. Each of the six channels is a single transistor with its collector open at the package pin, so no output-high voltage is driven internally; instead, an external pull-up resistor to any voltage up to 30 V defines the logic-high level. This permits conversion of 5 V TTL logic levels to MOS levels, wire-AND logic combining, and driving of lamps or relays with the external pull-up sized for the load current. Typical applications include driving LED indicators and relays from microcontroller or TTL outputs, level shifting between 5 V logic and higher-voltage MOS circuits, implementing wire-AND/wire-OR bus lines on shared nodes, and general TTL buffering in industrial control panels and test fixtures. In design, always provide an external pull-up resistor on every output, sized so the sink current stays below 40 mA and the pull-up dissipation is acceptable; do not use this part where an active drive-high output is required. This page synthesizes verified distributor data, drop-in alternatives, pinout, and practical design notes not found in the manufacturer datasheet.

RFQ İletişim
SN74LS07DR - Hex Buffer/Driver OC 30V 40mA | Texas Instruments
SN74LS07DR

SN74LS07DR - Hex Buffer/Driver OC 30V 40mA | Texas Instruments

The Texas Instruments SN74LS07DR is a hex non-inverting buffer and driver featuring high-voltage open-collector outputs rated at 30 V with a maximum sink current of 40 mA, supplied in a 14-pin SOIC (D) package. Operating from a 4.75 V to 5.25 V TTL supply over a 0 C to 70 C commercial temperature range, it performs level translation and high-current load driving in a single low-cost IC. A buffer/driver is a logic element that isolates and amplifies digital signals so a low-power logic output can drive heavier loads, longer buses, or circuits operating at different voltage levels. Buffers and drivers sit within the broader hierarchy of logic ICs, which spans gates, flip-flops, registers, and bus interface devices in standard 7400 TTL and CMOS families. Key features include open-collector outputs that interface directly with high-level circuits such as MOS gates, indicator lamps, and relays; a strong 40 mA sink-current capability well beyond standard TTL outputs; input clamping diodes that simplify system design by suppressing negative-going line transients; and operation as a straight-through non-inverting buffer for driving TTL inputs. These characteristics make it a classic choice for logic-to-power interfacing. Architecturally, the SN74LS07 is a bipolar LS-TTL device. Each of the six channels is a single transistor with its collector open at the package pin, so no output-high voltage is driven internally; instead, an external pull-up resistor to any voltage up to 30 V defines the logic-high level. This permits conversion of 5 V TTL logic levels to MOS levels, wire-AND logic combining, and driving of lamps or relays with the external pull-up sized for the load current. Typical applications include driving LED indicators and relays from microcontroller or TTL outputs, level shifting between 5 V logic and higher-voltage MOS circuits, implementing wire-AND/wire-OR bus lines on shared nodes, and general TTL buffering in industrial control panels and test fixtures. In design, always provide an external pull-up resistor on every output, sized so the sink current stays below 40 mA and the pull-up dissipation is acceptable; do not use this part where an active drive-high output is required. This page synthesizes verified distributor data, drop-in alternatives, pinout, and practical design notes not found in the manufacturer datasheet.

RFQ İletişim
SN74LS07DRE4 - Hex Buffer Open-Collector 30V | TI
SN74LS07DRE4

SN74LS07DRE4 - Hex Buffer Open-Collector 30V | TI

The Texas Instruments SN74LS07DRE4 is a hex non-inverting buffer/driver with high-voltage open-collector outputs rated at 30 V, 40 mA sink capability, and operation from a 4.75 V to 5.25 V supply, housed in a 14-pin SOIC (D) package. A buffer/driver is a logic element that isolates signal sources from loads and provides the current drive capability that standard logic outputs often lack. Within the power-management and interface hierarchy, buffers bridge low-power digital controllers and higher-current loads such as LEDs, relays, motors and high-level logic families. Open-collector buffers are a special class: the output transistor can only sink current, so the logic-high level is set by an external pull-up resistor, allowing level shifting between different voltage domains. Key features of the SN74LS07 include a rated output voltage of 30 V on the open-collector stage, a maximum sink current of 40 mA per output, six independent non-inverting elements in one package, and classic Low-Power Schottky (LS) TTL bipolar technology. The DRE4 ordering suffix denotes the 14-SOIC package in tape-and-reel packaging for automated assembly. Technically, the bipolar LS architecture provides fast switching with robust noise margins and rugged open-collector outputs suited for driving heavy loads. Because outputs are open-collector, they support wired-AND configurations where multiple outputs share a pull-up, a common technique for shared interrupt or status lines. Typical applications include driving high-current LED indicators, interfacing 5 V logic to high-level circuits up to 30 V, relay and solenoid drive, and TTL input buffering in industrial control panels. Design consideration: always provide a pull-up resistor to the desired high-level voltage; the open-collector output cannot source current, and the pull-up value trades speed against sink current. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ İletişim
SN74LS07N - 6-Channel Open-Collector Buffer | Texas Instruments
SN74LS07N

SN74LS07N - 6-Channel Open-Collector Buffer | Texas Instruments

The Texas Instruments SN74LS07N is a six-channel, non-inverting bipolar buffer and driver with open-collector high-voltage outputs, a 4.75 V to 5.25 V supply range, and a 30 V rated output voltage in a 14-PDIP package. Each channel provides input buffering for TTL-compatible signals and can sink up to 40 mA for relay, lamp, and other high-level interface loads. The open-collector architecture requires an external pull-up resistor and permits wired interfaces, level translation, and multiple drivers to share a bus safely when only one driver pulls low at a time. An open-collector buffer or driver is a digital interface IC whose output transistor can sink current but cannot actively source current. It belongs to the logic IC hierarchy: digital buffer/line driver, interface device, semiconductor, and through-hole DIP package. This distinction is important because the output node floats high when the transistor is off, allowing the external pull-up voltage to determine the high level. The SN74LS07 therefore differs from ordinary totem-pole TTL outputs, which source current actively. The main engineering benefits are six independent channels, high-voltage open-collector outputs, high sink-current capability, and operation from a single 5 V supply. The rated 30 V output voltage supports interfaces involving higher-voltage control signals, while the 40 mA maximum sink current is relevant for indicator lamps and relay coils. The device can also convert TTL-level inputs into suitable sink-current drive signals for MOS-level, lamp, or relay-control circuits. Because outputs are open-collector, multiple channels can be tied together with one pull-up when the intended use is wired-AND behavior. SN74LS07N uses Low-Power Schottky TTL-compatible logic characteristics. Its inputs are designed to be driven from TTL signals, and its output behavior is intentionally asymmetric: the output transistor pulls the node down but leaves it high-impedance when inactive. Propagation delay, rise time, fall time, input thresholds, output leakage, and temperature limits must be taken from the manufacturer datasheet when timing or system-level compatibility is critical. The supplied search results confirm the 4.75 V to 5.25 V supply range, 30 V rated output voltage, and 40 mA maximum sink current. Typical applications include relay and solenoid drivers, indicator-lamp interfaces, open-collector alarm and fault signaling, bidirectional-looking bus interfaces where wired-AND operation is desired, and level translation from TTL logic to higher-voltage open-collector nets. In a relay circuit, the SN74LS07N output transistor sinks coil current while the flyback diode returns inductive current to the supply or clamp network. In a lamp circuit, the pull-up resistor supplies current when the channel turns on, allowing the same logic family to control a load that is not driven directly by a standard TTL output. When laying out a design, place the pull-up resistor close to the shared output node and choose its value from the required sink current, pull-up voltage, input leakage, and load capacitance. Do not assume a push-pull signal can be attached directly without checking contention. Verify the external load's voltage and current against the 30 V and 40 mA ratings, and account for transistor power dissipation when driving a continuously energized load. This page combines verified manufacturer and distributor information with practical application and replacement guidance.

RFQ İletişim
SN74LS07NS - 6-Channel Open-Collector Buffer | Texas Instruments
SN74LS07NS

SN74LS07NS - 6-Channel Open-Collector Buffer | Texas Instruments

Texas Instruments SN74LS07NS is a six-channel, non-inverting bipolar buffer and driver with open-collector high-voltage outputs, operating from 4.75 V to 5.25 V in a 14-pin SOIC package. The device provides six independent channels, a 40 mA low-level output current, and a TTL-compatible logic interface for driving compatible loads and pull-up networks. A logic buffer or driver is a digital IC that conditions and strengthens a signal so it can reliably drive another logic circuit. The SN74LS07 belongs to the 74-series bipolar logic hierarchy, where a buffer or driver sits between digital logic ICs and external loads. Its open-collector outputs require an external pull-up resistor, allowing the output stage to disconnect electrically when the output is low. Key features include six non-inverting channels, open-collector output design, a 4.75 V to 5.25 V supply range, 40 mA sink-current capability, 14 mA quiescent current, and approximately 45 mA operating supply current. The open-collector architecture is useful when multiple compatible outputs must share a wired bus or when an interface requires an externally selected pull-up voltage. The SN74LS07NS commercial temperature range is 0°C to 70°C. The bipolar SN74LS07 architecture is intended for conventional 5 V TTL systems rather than low-voltage CMOS designs. Because each output has an open-collector transistor rather than a totem-pole output stage, the board designer selects the pull-up resistor and determines the usable rise time from the bus capacitance. Input and output logic levels follow the SN74LS07 family specifications, while the low-level output current is specified at 40 mA. Typical uses include driving indicator lamps, relay interfaces, optocoupler inputs, level-shifting networks, and general-purpose open-collector digital buses. The SN74LS07NS is particularly appropriate when the driven device must share a pull-up rail or when a wired-AND/open-collector connection is required. It can also buffer TTL signals for short interconnect distances within a 5 V system. Choose the pull-up resistor and trace length together because the external resistor and total bus capacitance determine the output rise time. Keep the pull-up connection short, use a resistor value suitable for the required sink current, and account for the 40 mA output rating when calculating the worst-case low-state load. The open-collector output can remain off during reset or power-loss conditions, which may be beneficial in fail-safe interface arrangements. This product page combines the SN74LS07NS electrical characteristics, package details, pin-compatible alternatives, pricing evidence, and practical design guidance into an engineering-focused reference for selecting and implementing this six-channel open-collector buffer.

RFQ İletişim
SN74LS138 - 3-to-8 Decoder/Demultiplexer LS-TTL | TI
SN74LS138

SN74LS138 - 3-to-8 Decoder/Demultiplexer LS-TTL | TI

The SN74LS138 is a 3-line to 8-line decoder/demultiplexer from Texas Instruments, part of the 74LS family of Schottky-clamped TTL MSI circuits designed for high-performance memory decoding and data-routing applications requiring very short propagation delay times. It provides three binary select inputs (A, B, C), three enable inputs (G1, G2A, G2B), and eight active-low outputs (Y0-Y7), operating from a 5V supply over 0C to +70C. A decoder is a combinational logic circuit that converts binary information from n input lines to a maximum of 2^n unique output lines. The 3-to-8 decoder is a fundamental building block in digital systems, used to select one of eight devices based on a 3-bit address. As an MSI device, it sits between SSI gates and LSI circuits in the digital logic hierarchy, and decoders are essential in memory address decoding where they enable specific memory chips. Key features include a typical propagation delay of 20 ns, low LS-TTL power dissipation (about 32 mW typical), and active-low outputs that sink up to 8 mA. The three enable inputs allow cascading multiple decoders into larger arrays (e.g., 4-to-16) and gating the device with control signals. Schottky-clamped TTL technology delivers high speed with good noise immunity and full TTL compatibility with 74LS, 74ALS, and 74AS families. The device is offered in 16-pin PDIP (N), SOIC (D), and SOP (NS) packages; the SN74LS138N in 16-PDIP is popular for through-hole and breadboard prototyping. According to the TI datasheet, the SN74LS138 is characterized from 0C to 70C for commercial operation. Typical applications include memory chip-select decoding in microprocessor systems, peripheral address decoding, and demultiplexing a single data line to one of eight outputs. Design tip: enable the device by driving G1 high and G2A/G2B low; tie unused inputs to valid logic levels to avoid floating nodes, and exploit the active-low outputs to drive active-low chip-select pins directly.

RFQ İletişim
SN74LS145 - BCD-to-Decimal Decoder/Driver | Texas Instruments
SN74LS145

SN74LS145 - BCD-to-Decimal Decoder/Driver | Texas Instruments

The SN74LS145 is a monolithic BCD-to-decimal decoder/driver with open-collector outputs, designed to accept BCD inputs and provide appropriate outputs to drive 10-digit incandescent displays. It consists of eight inverters and ten four-input NAND gates, with the inverters connected in pairs to make BCD input data available for decoding by the NAND gates. Full decoding of valid BCD input logic ensures that all outputs remain off for all invalid binary input conditions. The device is available in a 16-pin PDIP package with through-hole mounting, making it suitable for legacy and new designs requiring high-voltage, high-current sinking capability. A BCD-to-decimal decoder is a combinational logic circuit that converts a 4-bit binary-coded decimal (BCD) input into one of ten decimal outputs. The SN74LS145 is a specific implementation that includes open-collector output transistors capable of sinking up to 80 mA at 15 V, allowing direct drive of relays, incandescent lamps, and other high-current loads. This decoder/driver sits within the broader hierarchy of digital logic ICs, specifically within the 74LS family of low-power Schottky TTL devices, which are known for their speed and compatibility with TTL, DTL, and MOS logic levels. Key features of the SN74LS145 include high-breakdown output transistors rated at 15 V, each capable of sinking up to 80 mA of current. Each input is one Series 54/74 or Series 54LS/74LS standard load, ensuring easy interfacing with other TTL logic. The open-collector outputs allow wired-OR connections and level shifting, providing design flexibility. The device operates over a wide supply voltage range and is compatible with standard TTL power supplies (5 V). The SN74LS145 uses low-power Schottky (LS) technology, which reduces power dissipation compared to standard TTL while maintaining high speed. The open-collector outputs are implemented with high-voltage transistors, enabling the device to drive loads connected to higher voltage rails (up to 15 V) while the logic operates at 5 V. This architecture is particularly useful in industrial control and display applications where loads require higher voltages than the logic supply. Typical applications include driving incandescent displays, relay drivers, and other high-current loads in industrial control systems, test equipment, and consumer electronics. The device is also used in BCD-to-decimal decoding for seven-segment displays, though it requires external current-limiting resistors. Its ability to sink 80 mA per output makes it suitable for driving relays and lamps directly, reducing the need for additional driver transistors. When designing with the SN74LS145, ensure that the output load current does not exceed the 80 mA rating and that the output voltage does not exceed 15 V. Pull-up resistors may be required when driving logic inputs from the open-collector outputs. The device is not recommended for new designs due to its obsolescence, but it remains available for legacy system maintenance.

RFQ İletişim
SN74LS17N - Hex Open-Collector Buffer Driver | Texas Instruments
SN74LS17N

SN74LS17N - Hex Open-Collector Buffer Driver | Texas Instruments

The Texas Instruments SN74LS17N is a six-channel, non-inverting buffer and driver with open-collector high-voltage outputs, a 14-pin DIP package, and a 0°C to 70°C commercial temperature range. The device provides six independent channels with input clamping diodes, high sink-current capability, and open-collector outputs designed for driving indicator lamps, relays, and MOS-level interfaces. Its open-collector architecture requires an external pull-up resistor and permits wired-AND or wired-OR connections when the system bus design requires them. What is a buffer or logic driver? A buffer is a digital IC that reproduces a logic signal at a compatible voltage and current level, while a driver adds output-current capability for loads beyond ordinary logic-gate fanout. The SN74LS17N belongs to the 74LS low-power Schottky TTL logic family, which is part of the broader digital IC and logic-IC hierarchy. Its open-collector outputs can sink current from an external pull-up network, making it useful where a driven device must share a bus or where system shutdown must actively pull a line low. Key features include six non-inverting channels, open-collector high-voltage outputs, input clamping diodes, and high sink-current capability. The verified product description specifically identifies the device as suitable for converting TTL voltage levels to MOS levels and driving indicator lamps and relays. Because the outputs are open collector, voltage rise time depends on the pull-up resistor, load capacitance, and the driven load rather than being determined only by the IC output stage. This makes resistor and capacitance selection important in time-sensitive systems. The SN74LS17N uses a 14-pin through-hole DIP package, with a commercial-grade temperature range of 0°C to 70°C. The provided sources identify the function, package class, channel count, terminal count, open-collector output architecture, input clamping, and high sink-current capability. Detailed electrical limits such as supply voltage, output current, propagation delay, input and output voltage levels, and absolute maximum ratings were not included in the supplied verified excerpts and are therefore marked for data retrieval rather than guessed. Typical applications include TTL-to-MOS level conversion, relay-driver circuits, indicator-lamp interfaces, alarm and status signaling, and digital control lines requiring active-low open-collector behavior. An external pull-up resistor must be selected so that its sink current remains within the SN74LS17N output specification and so that the resulting RC rise time meets the receiving circuit's timing requirements. Multiple open-collector outputs can be connected to a common pull-up for wired logic, provided the aggregate sink-current limit is respected. When designing a replacement board, preserve the 14-pin DIP pinout and account for open-collector output behavior. Do not assume a push-pull output can be substituted without reviewing the pull-up network and downstream load. Verify the external pull-up voltage, relay-coil current, logic thresholds, temperature requirements, and timing budget against the complete manufacturer datasheet before production release.

RFQ İletişim
SN74LS191N - 4-Bit Synchronous Up/Down Counter | Texas Instruments
SN74LS191N

SN74LS191N - 4-Bit Synchronous Up/Down Counter | Texas Instruments

The Texas Instruments SN74LS191N is a synchronous 4-bit binary up/down counter with up/down mode control, packaged in a 16-pin PDIP. The counter provides one 4-bit counting element, positive-edge triggering, and a 58-equivalent-gate complexity. Its synchronous operation clocks all four internal flip-flops simultaneously, allowing the outputs to change on the same clock edge without the counting spikes normally associated with asynchronous counters. A synchronous counter is a logic device that advances or reverses its binary count on a common clock edge while internal steering logic determines the direction. The SN74LS191N belongs to the 74LS TTL family and operates within the broader hierarchy of counters, digital logic ICs, and logic semiconductors. Its four parallel outputs provide the current count, while separate control inputs support loading, counting enable, direction selection, and clearing functions. The main benefits of the SN74LS191N are its synchronous output behavior, independent up/down control, and straightforward 4-bit parallel counting. Because every state element changes at the same clock event, the device avoids the intermediate output states that can appear when an asynchronous ripple counter transitions between binary values. This makes it useful when downstream circuitry must observe stable count transitions. Internally, the SN74LS191 uses four edge-triggered flip-flops with common clocking and steering logic for count direction. A positive-edge clock transition advances the count when the direction input selects up-counting and decrements it when down-counting is selected. Control inputs provide parallel loading and count-enable behavior, allowing the counter to be synchronized with a larger digital system. The manufacturer datasheet identifies the device as a four-bit synchronous counter with 58 equivalent gates. Typical applications include digital frequency division, programmable sequence generation, industrial control counters, instrumentation timing, and general-purpose logic systems. It can also form the counting stage of a cascaded counter arrangement when a larger count range is required. The SN74LS191N is particularly appropriate when a four-bit parallel count must be loaded, enabled, cleared, or reversed under digital control. PCB design should preserve the 16-pin PDIP pin arrangement and provide adequate routing clearance around the through-hole device. Decoupling should be placed close to the power and ground pins, while clock and control traces should be kept short enough to minimize propagation-related timing errors. Confirm operating voltage, temperature grade, output drive, and timing limits in the manufacturer datasheet before applying the counter to new logic. This product page organizes the SN74LS191N function, verified distributor references, package information, practical design guidance, and verified drop-in alternatives. It also distinguishes synchronous counting from ripple-count behavior and provides application-oriented guidance for engineers evaluating the 74LS counter family.

RFQ İletişim
SN74LS193D - 4-Bit Synchronous Up/Down Counter | Texas Instruments
SN74LS193D

SN74LS193D - 4-Bit Synchronous Up/Down Counter | Texas Instruments

The Texas Instruments SN74LS193D is a synchronous 4-bit binary up/down counter with dual clock inputs and asynchronous clear, packaged in a 16-pin SOIC. Its four parallel outputs represent a binary count from 00H to 1111, while separate up and down clock inputs select the counting direction. The counter is suited to digital sequencing, frequency division, state advancement, and industrial control logic requiring deterministic parallel counting. A counter IC is a synchronous sequential-logic device that stores a binary value and changes that value in response to clock edges. The SN74LS193 belongs to the 74LS TTL family, which sits within the broader hierarchy of digital logic ICs, counters, binary counters, and standard-surface-mount logic. Because all internal flip-flops are clocked together, the four outputs update simultaneously instead of producing the ripple transitions associated with asynchronous counting stages. The key functional features are a 4-bit counting capacity, independent up-count and down-count clocks, a load input for parallel initialization, an asynchronous clear input, and a carry output for detecting overflow or underflow. The verified manufacturer description identifies the SN74LS193 as a synchronous 4-bit up/down binary counter with dual clock and clear. Its 16-SOIC package supports conventional surface-mount PCB assembly and is compatible with standard digital-logic design practices. Synchronous operation is the device's principal engineering advantage. Since the four output bits change on the same active clock edge, downstream combinational logic sees a coherent new binary state rather than intermediate count values. This simplifies decoding and reduces uncertainty in control systems. The separate clock inputs also allow the same physical counter to perform upward counting, downward counting, or operation from a selected direction-control clock without redesigning the board. Typical uses include programmable sequence generators, pulse and event counters, digital position indicators, frequency-divider stages, and control systems for industrial equipment. A load input can establish an initial count, and the carry output can flag the terminal count of 1111 during up counting or 0000 during down counting. These functions allow a single counter IC to coordinate multistage digital operations without requiring several separate accumulator devices. PCB design should preserve clear access to the clock, load, and clear inputs because asynchronous control signals must not be allowed to float. Use a defined logic level for every input and route clock traces away from noisy switching nodes. The manufacturer datasheet should be consulted for the exact pin-description table, recommended operating conditions, timing limits, and maximum input voltages before finalizing the circuit. This page combines the manufacturer function description, distributor package and pricing references, verified substitute data, and practical implementation guidance for engineers evaluating the SN74LS193D in legacy TTL, industrial-control, counter, and sequencing designs.

RFQ İletişim
SN74LS240H - 8-Channel 3-State Inverting Driver | onsemi
SN74LS240H

SN74LS240H - 8-Channel 3-State Inverting Driver | onsemi

onsemi SN74LS240H is an eight-channel bipolar octal buffer and line driver with inverting, three-state outputs, designed for operation from a 4.75 V to 5.25 V supply. The device is offered in a 20-pin PDIP package and provides eight independently controlled outputs for driving buses, memory interfaces, and other digital systems. An octal buffer or line driver is a digital logic IC that strengthens a signal so it can reliably drive multiple bus loads. The SN74LS240 family combines buffer operation with active-low output enable control, allowing each output to be placed into a high-impedance state when the associated output is not selected. This tri-state capability supports shared buses, bidirectional bus-interface arrangements, and designs that require controlled connection and isolation of multiple logic nodes. The key functional characteristics are eight inverting channels, a 4.75 V to 5.25 V supply range, three-state outputs, and a 20-pin PDIP package. The three-state outputs are particularly useful in bus-oriented equipment because disabled drivers do not actively contend with another logic source. The H designation identifies a distinct onsemi catalog configuration within the SN74LS240 family, so engineers should confirm ordering details, temperature range, and qualification requirements before release. The bipolar SN74LS240 architecture belongs to the Low-Power Schottky TTL logic family. Its buffered outputs are intended to improve signal integrity and drive capability when connecting processors, memory devices, peripheral controllers, and bus transceivers. Because the outputs invert, a low input produces a high output and a high input produces a low output when the output driver is enabled. Output-enable polarity must therefore be considered together with data inversion during system-level logic design. Typical applications include memory address driving, clock and control-line distribution, instrument-bus interfacing, industrial control systems, and legacy computer peripherals. In a shared-bus arrangement, the output-enable signal determines which driver section may actively connect to the bus while the other sections remain in the high-impedance state. In address-driver arrangements, the inverting channels can be assigned according to the required polarity of each memory-control signal. PCB implementation requires correct DIP pin orientation and adequate routing space around the 20-pin package. Power and ground pins should be connected with short traces and suitable bypass capacitance to limit transient current through package leads. Because outputs can source or sink bus current, external load capacitance, trace length, and simultaneous switching should be checked against the applicable device limits before using the part in high-speed or heavily loaded systems. This page consolidates the device function, verified catalog information, replacement considerations, and practical implementation guidance. It also distinguishes a genuine pin-compatible replacement from a merely similar logic function and emphasizes that system timing, output-enable polarity, package construction, temperature grade, and qualification requirements must be reviewed together before substitution.

RFQ İletişim
SN74LS240M - 8-Channel 3-State Inverting Buffer | onsemi
SN74LS240M

SN74LS240M - 8-Channel 3-State Inverting Buffer | onsemi

The onsemi SN74LS240M is an 8-channel bipolar inverting buffer and line driver with 3-state outputs, designed for operation from a 4.75 V to 5.25 V supply in an SOEIAJ-20 surface-mount package. Each device contains two 4-bit channels, and each output can be placed in the high-impedance state for shared-bus operation. The three-state capability allows multiple drivers to share a bus when only one device is actively driving at a time. A logic buffer is a digital integrated circuit that reproduces an input signal while providing buffering, isolation, and drive capability. A line driver strengthens digital signals for transmission across circuit-board traces or between logic sections. A bus transmitter combines that drive function with a three-state output, allowing the output to disconnect electrically when it is not selected. The SN74LS240M belongs to the 74LS bipolar logic family and is positioned within the hierarchy of logic integrated circuits, digital interface devices, and bus-oriented transmitters. The principal features are eight individually controlled inverting outputs, 4.75 V to 5.25 V operating voltage, and three-state output operation. Inverting operation means a low input level produces a high output level, while a high input level produces a low output level. Input hysteresis helps improve noise margins by defining distinct transition regions near the switching threshold. The device is intended for memory-address driving, clock driving, and general bus-oriented signal transmission where higher board density is useful. The SN74LS240M combines LS-series bipolar logic behavior with the practical benefits of a compact surface-mount package. Its inverting outputs are useful when a system requires complementary phase relationships or inversion between two logic stages. Because three-state outputs can be disabled, designers can prevent contention on shared data, address, or control buses by ensuring that only one driver is enabled during each transfer interval. Typical uses include memory and peripheral interface logic, buffered clock distribution, industrial control boards, computer bus interfaces, and embedded systems requiring a compact octal bus transmitter. In a shared-bus arrangement, output-enable signals determine which driver owns the bus, while the other devices maintain high-impedance outputs. This arrangement reduces electrical loading and helps prevent simultaneous-output contention. PCB design should provide a continuous ground plane, minimize return-current-loop area, and place input and output paths away from noisy switching nodes. Because the device is a bipolar logic part, supply and ground connections should be decoupled near the package, and unused inputs should be tied to a defined logic level rather than left floating. This page combines the device function, package information, replacement guidance, and practical interface considerations for faster engineering selection.

RFQ İletişim
SN74LS240N - 8-Channel 3-State Buffer | Texas Instruments
SN74LS240N

SN74LS240N - 8-Channel 3-State Buffer | Texas Instruments

The Texas Instruments SN74LS240N is an 8-channel inverting buffer and line driver with three-state outputs, designed for 4.75 V to 5.25 V bipolar TTL systems and supplied in a 20-pin PDIP package. Each of the four channels contains two inverter elements, allowing independent control of two output groups through the two output-enable inputs. A three-state buffer is a digital logic device that can present a low level, a high level, or a high-impedance state on its output. The SN74LS240N belongs to the 74LS TTL family, which occupies the logic buffer, line-driver, and bus-interface level of the broader semiconductor hierarchy. Its three-state outputs allow multiple drivers to share a bus when only one group is enabled at a time. Key characteristics include eight inverting outputs, four output elements, separate output-enable control for the two groups, and operation from a single 4.75 V to 5.25 V supply. The inverting function reverses the logic state presented at each enabled output. The three-state capability is especially useful in memory-address, clock, and bidirectional bus-interface systems where inactive drivers must be isolated rather than continuously switching a node. The SN74LS240N is a bipolar 74LS-series device rather than a low-power CMOS interface. This places it in applications built around conventional 5 V TTL logic, where system compatibility, established timing behavior, and direct bus interfacing are more important than very low supply current. Its four output elements are organized as two four-bit groups, and each group has a dedicated output-enable input. Typical uses include three-state bus drivers, memory-address drivers, clock-distribution buffers, industrial control interfaces, test equipment, and legacy computer or peripheral-control systems. Because every output is inverting, the device is appropriate where inverted logic is expected or where an inversion stage can simplify a wider bus arrangement. A non-inverting bus interface may instead require a different 74LS buffer function. When laying out a board, keep input and output traces short, provide a stable ground reference, and avoid forcing a three-state output into a logic-high or logic-low state while its driver is disabled. Confirm that enable polarity, propagation delay, fanout, and bus contention requirements fit the surrounding system. Use the manufacturer pin-description table when assigning PCB tracks and checking the two output-enable connections. This product page combines the SN74LS240N function, package, sourcing guidance, verified alternatives, and practical interface considerations. It also provides engineering-focused comparisons for selecting an inverting three-state bus buffer without confusing it with non-inverting or differently controlled 74LS devices.

RFQ İletişim
SN74LS241N - Octal 3-State Buffer | Texas Instruments
SN74LS241N

SN74LS241N - Octal 3-State Buffer | Texas Instruments

The Texas Instruments SN74LS241N is an octal, non-inverting buffer and line driver with eight 4-bit elements, individual output-enable control, and three-state outputs in a 20-pin PDIP package. The device operates from 4.75 V to 5.25 V and belongs to the LS-series bipolar logic family. Its buffered outputs provide stronger signal drive than ordinary TTL gates while preserving non-inverting logic behavior. A buffer or line driver is a digital logic component that isolates a source from a load, provides signal gain, and improves drive capability within a logic system. The SN74LS241N hierarchy is octal buffer > non-inverting buffer > three-state line driver > bipolar logic IC > integrated circuit. Three-state outputs can place an output in the active-high, active-low, or high-impedance state, allowing multiple devices to share a data bus when only one driver is enabled at a time. Each device contains eight non-inverting buffer elements. Two output-enable inputs control groups of four outputs, allowing two independently controlled four-bit sections. The three-state feature helps reduce bus contention, supports controlled disconnect from shared buses, and permits external test equipment to access nodes without permanently driving them. The NS suffix denotes the standard commercial-temperature ordering option, while N identifies the PDIP package. The SN74LS241 uses bipolar LS-series logic technology at a nominal 5 V supply. The manufacturer product page specifies an 8-channel, 4.75 V to 5.25 V bipolar buffer with three-state outputs. Because the device is a buffer rather than a level shifter, its input and output voltage thresholds remain tied to the same 5 V LS logic environment. Power and timing behavior should be evaluated against the limits in the manufacturer datasheet for the selected load and temperature range. Typical uses include computer peripheral data buses, bidirectional or multiplexed bus-interface sections, address and data-line buffering, industrial control systems, and legacy test equipment. The SN74LS241N is especially useful where a source must drive multiple loads or where two independently enabled four-bit groups need to share a common bus. It can also buffer control signals while leaving the corresponding output disconnected during a test or reset interval. Keep input and output timing requirements in mind when cascading bus devices. The output-enable pins should be controlled so that two drivers never actively oppose each other on the same node. For a bus, designate an arbitration or priority scheme, disable all inactive drivers, and account for enable and propagation delays when changing ownership. Decoupling and unused input handling should follow the connection recommendations in the manufacturer datasheet. This page organizes the SN74LS241N electrical characteristics, package details, drop-in alternatives, and application guidance for faster engineering evaluation. It also highlights the distinctions between enabled and high-impedance operation, identifies where the device differs from related LS-series buffers, and provides practical guidance for legacy-system repair, bus interfacing, and new multi-driver logic designs.

RFQ İletişim