Ürünler (46.000+)

SP485EMN-L - 10Mbps Low-Power RS-485 Transceiver | MaxLinear
SP485EMN-L

SP485EMN-L - 10Mbps Low-Power RS-485 Transceiver | MaxLinear

The MaxLinear SP485EMN-L is a low-power, half-duplex RS-422/RS-485 interface transceiver with a 10,000 kbps data rate, enhanced ESD protection, and an 8-pin SOIC package. It operates from a 4.75 V to 5.25 V supply and is designed for bidirectional industrial data links requiring one driver and one receiver. Its enhanced low-EMI implementation and BiCMOS process support reliable communication over longer, noisy cable runs. An RS-485 transceiver is an interface IC that combines a differential line driver and differential receiver into a physical-layer component for balanced serial communication. The SP485 belongs to the RS-422/RS-485 interface hierarchy within the broader semiconductor and industrial communications market. Half-duplex operation means the driver and receiver share the same differential pair, allowing the connected device to transmit or receive, but not both simultaneously. Key features include support for both RS-422 and RS-485 protocols, operation across a 4.75 V to 5.25 V supply range, a maximum data rate of 10,000 kbps, and an industrial temperature range of -40°C to +125°C. The SP485EMN-L family also provides enhanced ESD tolerance of more than ±15 kV for both the human body model and the IEC 61000-4-2 air-discharge method, improving protection during cable connection and industrial installation. The BiCMOS architecture combines bipolar and CMOS characteristics to provide low-power operation without sacrificing data-rate performance. A single driver and single receiver support point-to-point and multidrop bus arrangements when the system includes the required biasing, termination, protection, and protocol controls. The low-EMI designation is particularly relevant to industrial environments where radiated emissions and cable transients can affect neighboring equipment. Typical applications include industrial serial buses, building automation controllers, factory data acquisition, remote sensor nodes, industrial gateways, and instrumentation links. The device can also bridge a legacy UART or microcontroller port to a balanced RS-485 network. Its wide temperature range and enhanced ESD performance make it suitable for equipment exposed to temperature variation and electrostatic discharge during field installation or maintenance. Designers should provide termination at both ends of the bus, bias the differential pair at one location, route the driver and receiver outputs as a balanced pair, and keep unprotected cable connectors away from sensitive logic. Supply and ground decoupling should be placed close to the IC. The half-duplex DE and /RE control functions must be sequenced so that the driver is disabled while the receiver remains active during bus turnaround. This product data combines verified distributor availability, package and electrical information, candidate drop-in comparisons, and practical implementation guidance. It is intended to help engineers evaluate the SP485EMN-L for industrial RS-485 designs, verify board compatibility, and identify the electrical and layout conditions needed for dependable field operation.

RFQ İletişim
SP485EMN-L/TR - 5Mbps RS-485 Transceiver | MaxLinear
SP485EMN-L/TR

SP485EMN-L/TR - 5Mbps RS-485 Transceiver | MaxLinear

The MaxLinear SP485EMN-L/TR is a low-power, half-duplex RS-422/RS-485 line transceiver with one driver and one receiver, operating at data rates up to 5 Mbps in an 8-pin SOIC package. The device uses a BiCMOS architecture to combine low power consumption with RS-485 and RS-422 performance, while enhanced ESD protection supports industrial communication equipment exposed to electrostatic discharge. An RS-485 transceiver is a physical-layer interface IC that converts logic-level signals into differential bus signals and receives differential bus signals back into CMOS-compatible logic. In the hierarchy, the SP485EMN-L/TR is a half-duplex line transceiver, part of the broader RS-422/RS-485 interface IC and interface-driver/receiver family within integrated interface semiconductors. Differential signaling improves noise immunity by rejecting common-mode voltage that can disrupt single-ended logic interconnects. The principal verified features are one driver, one receiver, half-duplex operation, RS-422 and RS-485 protocol support, operation up to 5 Mbps, and low-power BiCMOS design. The SP485EMN-L/TR also provides enhanced ESD performance, with available comparison data indicating tolerance above ±15 kV for the human-body model and IEC 61000-4-2 air-discharge method. The 8-pin SOIC package is compatible with standard surface-mount assembly and leaded-solder inspection processes. A typical half-duplex circuit connects the transceiver driver and receiver to the same differential pair through direction-control logic. The DE and RE inputs determine whether the node transmits or receives. Designers must manage driver enable timing, bus turnaround delays, termination, biasing, and protection-network placement to avoid contention and receiver misinterpretation during direction changes. Common applications include industrial automation links, building-control networks, remote sensor modules, industrial instrumentation, and long-distance RS-485 equipment links. The 5-Mbps capability supports high-speed point-to-point or multipoint industrial buses, while the low-power BiCMOS implementation is useful when system-level energy consumption matters. The main design consideration is the transceiver interface around the SOIC-8 pins. Keep the bus trace path short, preserve symmetry between differential conductors, place termination only at physical bus endpoints, and use suitable common-mode protection for exposed cables. The DE/RE control signals should be sequenced so the receiver is enabled before the driver transmits and the driver is disabled before the receiver switches. This page combines manufacturer-family information, distributor availability, package details, verified cross-reference results, replacement guidance, and application-specific engineering notes to help engineers evaluate the SP485EMN-L/TR beyond a basic distributor listing.

RFQ İletişim
SP485EN-L - 5Mbps RS-485/RS-422 Transceiver | MaxLinear
SP485EN-L

SP485EN-L - 5Mbps RS-485/RS-422 Transceiver | MaxLinear

MaxLinear SP485EN-L is a single half-duplex differential transceiver for RS-485 and RS-422 links, supporting data rates up to 5Mbps from a 4.75V to 5.25V supply in an 8-pin SOIC package. Its BiCMOS implementation combines low power with differential line-driver and receiver functions. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential transmissions and reconstructs received data from differential bus voltage. These transceivers form the physical communication layer between processors, controllers, sensors, and remote equipment, with RS-422 commonly supporting point-to-point links and RS-485 supporting multipoint buses. The SP485EN-L family provides half-duplex operation, one differential driver, and one differential receiver. Its 5Mbps capability suits high-rate industrial, instrumentation, and embedded links, while the 5V-only operating range makes supply compatibility a central design consideration. A nominal 5V supply is accepted, and the verified operating range extends from -40°C to 85°C. The BiCMOS process is intended to reduce power use relative to older bipolar transceiver designs without sacrificing line performance. The receiver uses differential inputs with Schmitt-trigger behavior, supporting robust decoding of signals shaped by cable attenuation, reflections, and common-mode noise. Exact driver load, receiver sensitivity, propagation delay, and input-current figures are not present in the supplied verified data and therefore require confirmation from the manufacturer datasheet. Typical uses include industrial controller links, factory automation equipment, remote sensor networks, data acquisition units, building controls, and embedded serial buses. In a half-duplex design, the direction-control signal determines whether the device transmits or receives; only the selected node should enable its driver to prevent multiple drivers from driving the same bus. Place the transceiver close to the bus connector and provide the decoupling and protection required by the system. A common RS-485 layout uses a low-impedance ground reference alongside A, B, and the differential pair. External protection, termination, biasing, and isolation remain application-specific choices rather than functions confirmed as integrated into the SP485EN-L. This product summary combines the verified distributor, manufacturer, and cross-reference information with practical RS-485 design guidance. It distinguishes documented parameters from missing electrical details, focuses on the genuine 8-pin drop-in alternatives, and helps engineers evaluate supply, speed, temperature, bus topology, and protection requirements before procurement.

RFQ İletişim
SP485EN-L/TR - 5Mbps RS-485/RS-422 Transceiver | MaxLinear (Tape & Reel)
SP485EN-L/TR

SP485EN-L/TR - 5Mbps RS-485/RS-422 Transceiver | MaxLinear (Tape & Reel)

MaxLinear SP485EN-L/TR is a single half-duplex differential transceiver for RS-485 and RS-422 links, supporting data rates up to 5Mbps from a 4.75V to 5.25V supply in an 8-pin SOIC package. Its BiCMOS implementation combines low power with differential line-driver and receiver functions. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential transmissions and reconstructs received data from differential bus voltage. These transceivers form the physical communication layer between processors, controllers, sensors, and remote equipment, with RS-422 commonly supporting point-to-point links and RS-485 supporting multipoint buses. The SP485EN-L/TR family provides half-duplex operation, one differential driver, and one differential receiver. Its 5Mbps capability suits high-rate industrial, instrumentation, and embedded links, while the 5V-only operating range makes supply compatibility a central design consideration. A nominal 5V supply is accepted, and the verified operating range extends from -40°C to 85°C. The BiCMOS process is intended to reduce power use relative to older bipolar transceiver designs without sacrificing line performance. The receiver uses differential inputs with Schmitt-trigger behavior, supporting robust decoding of signals shaped by cable attenuation, reflections, and common-mode noise. Exact driver load, receiver sensitivity, propagation delay, and input-current figures are not present in the supplied verified data and therefore require confirmation from the manufacturer datasheet. Typical uses include industrial controller links, factory automation equipment, remote sensor networks, data acquisition units, building controls, and embedded serial buses. In a half-duplex design, the direction-control signal determines whether the device transmits or receives; only the selected node should enable its driver to prevent multiple drivers from driving the same bus. Place the transceiver close to the bus connector and provide the decoupling and protection required by the system. A common RS-485 layout uses a low-impedance ground reference alongside A, B, and the differential pair. External protection, termination, biasing, and isolation remain application-specific choices rather than functions confirmed as integrated into the SP485EN-L/TR. This product summary combines the verified distributor, manufacturer, and cross-reference information with practical RS-485 design guidance. It distinguishes documented parameters from missing electrical details, focuses on the genuine 8-pin drop-in alternatives, and helps engineers evaluate supply, speed, temperature, bus topology, and protection requirements before procurement.

RFQ İletişim
SP485ES-L 5Mbps RS-485 Transceiver | MaxLinear | 8-PDIP
SP485ES-L

SP485ES-L 5Mbps RS-485 Transceiver | MaxLinear | 8-PDIP

The MaxLinear SP485ES-L is a single-channel, half-duplex RS-485 and RS-422 transceiver capable of operation up to 5000 kbps, supplied in an 8-pin plastic DIP package. The device combines one driver and one receiver with a BiCMOS design intended to provide low-power operation without sacrificing communication performance. Its differential bus pins support the physical layer used by industrial automation, instrumentation, building controls, and other long-distance serial networks. An RS-485 transceiver is an interface IC that converts logic-level data into a differential, balanced signal and converts received differential signals back into digital logic. The broader hierarchy is transceiver > serial interface > differential line interface > interface IC. RS-485 is commonly used for robust multidrop communication, while the SP485ES-L also supports RS-422 signaling as described by the manufacturer. Key features include a maximum data rate of 5000 kbps, a half-duplex 1/1 transceiver configuration, and an operating temperature range from -40 C to +85 C. The BiCMOS implementation combines bipolar and CMOS characteristics to support low-power operation. Because the device is half duplex, its driver and receiver share the bus connection and are controlled separately through DE and RE logic inputs. The SP485ES-L provides separate driver input, driver enable, receiver enable, and receiver output functions. This arrangement allows a design to disable the transmitter during reception, supporting bus turnaround in two-wire RS-485 networks. The exact differential input thresholds, output levels, supply current, driver impedance, receiver impedance, and protection ratings are not supplied in the retrieved source excerpts and therefore must be confirmed in the manufacturer datasheet before final circuit design. Typical uses include industrial RS-485 field buses, factory automation equipment, building automation controllers, data acquisition systems, motor-control interfaces, and embedded serial networks. The 5000 kbps capability makes the part suitable for relatively high-speed point-to-point or multidrop links where cable length, topology, termination, and transceiver slew rate remain compatible. Design with the SP485ES-L using a local 5 V supply only after checking the complete electrical limits in the datasheet. Place the transceiver close to the bus connector, provide the protection required by the installation environment, and apply termination and fail-safe biasing according to the selected bus topology. ESD and surge protection may require external components because the retrieved data does not establish the integrated protection rating. This page consolidates the verified package, speed, interface, temperature, sourcing, and cross-reference information with practical selection guidance. It also distinguishes the SP485ES-L from candidate drop-in devices and identifies electrical details that still require datasheet confirmation, providing more engineering context than a distributor listing alone.

RFQ İletişim
SP485R - 1/10 Unit Load RS-485 Transceiver | MaxLinear
SP485R

SP485R - 1/10 Unit Load RS-485 Transceiver | MaxLinear

The MaxLinear SP485R is a low-power RS-485 differential transceiver offered in an 8-pin narrow SOIC or 8-pin plastic DIP package, designed as a pin-to-pin equivalent to the SP485 with significantly higher receiver input impedance. The part supports half-duplex communication with tri-state control and is intended for applications that require many nodes on a single twisted-pair bus, rated for over 400 transceivers per line due to its high-impedance differential receiver inputs (RIN approximately 120 kOhm to 150 kOhm typical). The SP485R operates from a single 5 V supply, delivers 5 Mbps signaling capability, and includes a low-power shutdown mode, making it suitable for industrial multi-drop networks, building automation, and long-cable installations. An RS-485 transceiver is a physical-layer interface IC that converts between a UART's TTL/CMOS logic levels and the differential voltage signaling required by the TIA/EIA-485 standard. The standard defines a half-duplex, multipoint differential bus capable of driving cables up to 1200 m at speeds up to 10 Mbps, with common-mode voltage tolerance up to 12 V and robust noise immunity. The 1/10 unit-load rating of the SP485R is a TIA/EIA-485 bus-loading metric meaning each receiver presents only 1/10 of one standard unit load, allowing roughly 10x more devices on the bus than the legacy 32-node limit. Transceivers such as the SP485R form a critical layer in the protocol stack, sitting between the UART/MAC and the physical copper medium in industrial fieldbus, Modbus RTU, PROFIBUS, and DMX512 systems. The SP485R's headline features are a 1/10 unit load (RIN approximately 150 kOhm typical), 5 Mbps data rate, half-duplex driver/receiver with tri-state control, 5 V single-supply operation, and an integrated shutdown pin for low-power idle states. Differential driver outputs swing the EIA-485-required 1.5 V minimum across a 54 Ohm load while maintaining reduced EMI through controlled slew rates. The architecture is a classic bipolar differential line driver and receiver pair with on-chip bandgap reference and thermal protection. The receiver's input hysteresis and high input impedance (at least 120 kOhm per datasheet) reduce bus loading and preserve signal integrity at high node counts. Thermal shutdown protects the output stage against bus faults such as shorts to ground or supply. Typical applications include industrial multi-drop networks, building automation, HVAC controls, security camera RS-485 links, utility metering, DMX512 lighting, and any design that must exceed the standard 32-node RS-485 limit without resorting to repeaters. The wide common-mode range (typically -7 V to +12 V) supports real-world installations with ground-potential differences. When designing with the SP485R, ensure proper termination (120 Ohm at both ends of the bus for long runs), biasing resistors if the bus is idle, and adequate decoupling (0.1 uF ceramic close to VCC). Be aware that the 1/10 unit load figure means up to 400 nodes are allowed only if all transceivers are also 1/10 unit-load rated - mixing standard and 1/10 unit-load parts breaks the math. This page synthesizes real distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ İletişim
SP485RCN-L - 1/10-Unit-Load RS-485 Transceiver | MaxLinear
SP485RCN-L

SP485RCN-L - 1/10-Unit-Load RS-485 Transceiver | MaxLinear

MaxLinear SP485RCN-L is a 1/10-unit-load RS-485 and RS-422 half-duplex transceiver with high receiver input impedance, a 4.75 V to 5.25 V supply range, and data rates up to 5 Mbps, housed in an 8-pin SOIC package. Its BiCMOS implementation supports low-power operation while preserving robust differential bus performance. An RS-485 transceiver is a physical-layer interface IC that combines a differential line driver and receiver on a balanced two-wire bus. The SP485 family supports RS-485 and RS-422 operation, while the SP485R high-fanout version raises receiver input impedance and can accommodate more than 400 transceivers on one transmission line without materially degrading the driver signal. The SP485RCN-L offers several practical benefits for industrial communication equipment. Its 1/10-unit-load receiver allows many devices to share the same bus without requiring a separate termination for every node. High receiver input impedance reduces loading in multi-drop networks, while the 5 Mbps maximum data rate supports both legacy industrial baud rates and faster point-to-point links. The SP485R architecture is described by the manufacturer as pin-to-pin equivalent to the original SP485 while adding high receiver input impedance and enhanced ESD tolerance. This makes it suitable for designs migrating from a conventional SP485 footprint when fan-out or transient robustness is important. The half-duplex arrangement allows the same differential pair to support transmission and reception, although direction control must be managed by the host logic. Typical applications include industrial PLC and factory automation links, building-control networks, instrumentation buses, motor-control equipment, security systems, and communications equipment that must place multiple transceivers on a single RS-485 segment. The 8-pin narrow SOIC package also supports compact board layouts where a higher-density interface solution would otherwise consume unnecessary area. Designers should use the manufacturer pin-description table when assigning PCB tracks, place the transceiver close to the connector, and apply suitable protection to the external bus. Termination, biasing, common-mode range, and isolation requirements must be evaluated together because the transceiver itself does not remove the need for correct bus topology and surge protection. This product data combines the SP485 family architecture, package information, manufacturer guidance, and drop-in comparison guidance to support faster schematic review, PCB-footprint validation, and sourcing decisions for industrial RS-485 and RS-422 interfaces.

RFQ İletişim
SP485RCN-L/TR - 5Mbps RS-485 Transceiver | MaxLinear
SP485RCN-L/TR

SP485RCN-L/TR - 5Mbps RS-485 Transceiver | MaxLinear

MaxLinear SP485RCN-L/TR is a 5 Mbps half-duplex RS-485 and RS-422 interface transceiver with one transmitter and one receiver, a 4.75 V to 5.25 V supply range, and an 8-pin SOIC package. Its 1/10-unit-load receiver supports more than 400 transceivers on one transmission line, while the high-impedance receiver input helps preserve the driver signal in multi-node networks. An RS-485 transceiver is a bidirectional communications interface that combines a differential line driver and differential receiver on a single integrated circuit. RS-485 defines a physical layer for robust, multipoint, balanced digital data links, while RS-422 provides a related differential signaling system. These transceivers operate within the interface IC and data-communications hierarchy, converting between logic-level signals and balanced differential signals used by industrial, building, and telecommunications equipment. The SP485RCN-L/TR combines a 5 V BiCMOS implementation with operation at rates up to 5 Mbps. Key electrical features include a typical receiver input resistance of 150 kohm and support for more than 400 units on a single line. The device is intended for half-duplex communication, uses an 8-pin narrow SOIC package, and is supplied in tape-and-reel packaging. Its operating temperature range is 0 °C to 70 °C. The BiCMOS architecture combines bipolar and CMOS characteristics to provide low-power operation without sacrificing line-driver performance. Separate receiver and driver control inputs permit the design to select receive, transmit, or disabled operating states. This flexibility is useful when direction control is handled by a microcontroller, transceiver logic, or an automatic control circuit. The high receiver impedance is particularly valuable in large RS-485 networks where loading from many connected receivers could otherwise reduce bus signal amplitude. Typical uses include industrial RS-485 controllers, building-automation equipment, instrumentation links, motor-control systems, and communications between a host controller and distributed remote nodes. The 5 Mbps capability supports relatively fast short-distance balanced links, while the 1/10-unit-load receiver allows numerous devices to share a bus when cable length, topology, termination, and transceiver loading permit. Design the bus with correct differential routing, a termination strategy suited to the network topology, and protection appropriate for the installation environment. Keep the driver, receiver, and bypass-capacitor connections compact, and account for common-mode voltage and ground potential differences between remotely connected nodes. The MAX485ESA cross-reference page identifies direct drop-in options and notes that minor parametric differences may exist, so verify every replacement against the required data rate, unit load, and bus topology. This product page combines manufacturer-level interface characteristics, package and environmental information, drop-in replacement guidance, and practical network-design considerations. It helps engineers evaluate the SP485RCN-L/TR beyond basic catalog attributes and select a compatible replacement without changing the 8-pin PCB footprint.

RFQ İletişim
SP485RCN/TR - 1/10 Unit Load RS-485 Transceiver | Sipex
SP485RCN/TR

SP485RCN/TR - 1/10 Unit Load RS-485 Transceiver | Sipex

The Sipex SP485RCN/TR is a 1/10-unit-load, half-duplex RS-485 transceiver designed for multipoint industrial communication networks. It supports more than 400 transceivers on one transmission line, provides a typical receiver input impedance of 150 kΩ, and accepts common-mode input voltages to +12 V. The device is packaged in an 8-pin SOIC for surface-mount assemblies. An RS-485 transceiver is a physical-layer interface integrated circuit that combines a differential line driver with a differential receiver. It belongs to the hierarchy of RS-485 interface IC, communications transceiver, interface IC, and semiconductor. This combination supports bidirectional data transfer over a balanced pair of wires while providing the common-mode tolerance and loading characteristics required for distributed industrial buses. The SP485RCN/TR's 1/10-unit-load receiver input is its defining network-loading feature. Unlike a standard-unit-load device, it reduces the loading presented by each connected node, allowing more than 400 transceivers to share a transmission line. Its typical 150 kΩ receiver input impedance helps preserve signal integrity when multiple nodes are connected, while its +12 V common-mode input range supports systems in which the bus voltage can move substantially above the receiver reference ground. The SP485R architecture provides a half-duplex transceiver arrangement in which one interface is used for transmission and reception. Direction control allows the connected controller or transceiver to determine when the driver is active. This arrangement is suited to bus architectures where devices share the same differential pair and transmit in a controlled sequence, avoiding simultaneous bus contention. Typical uses include industrial process-control networks, factory automation equipment, building-control systems, instrumentation, and other multidrop RS-485 networks. The reduced unit load is particularly useful where many field devices must share one cable run. The SP485RCN/TR is also suitable for systems that need the extended common-mode input range of +12 V. PCB design should preserve the differential signal path from the transceiver through the connector, maintain closely matched routing for the A and B conductors, and provide a suitable return path to reduce common-mode conversion. Bus topology, termination, fail-safe biasing, and protection requirements must be evaluated at the network level because correct transceiver selection alone does not guarantee reliable communication. This page combines the device's RS-485 network-loading characteristics with practical application guidance, interface comparisons, pinout-document links, and design notes for engineers evaluating the SP485RCN/TR in multidrop industrial communication systems.

RFQ İletişim
SP485RCP-L - 1 Mbps RS-485 Transceiver | MaxLinear
SP485RCP-L

SP485RCP-L - 1 Mbps RS-485 Transceiver | MaxLinear

The MaxLinear SP485RCP-L is a half-duplex RS-422/RS-485 interface transceiver with one driver and one receiver, a maximum data rate of 1 Mbps, and an 8-pin PDIP package. The device operates from a nominal 5.25 V supply and is specified for the 0°C to 70°C commercial temperature range, making it suitable for conventional industrial and legacy communications equipment. An RS-485 transceiver is a physical-layer interface IC that combines a differential line driver with a differential receiver. It belongs to the hierarchy of transceiver, interface IC, communications semiconductor, and semiconductor. RS-485 signaling supports robust point-to-multipoint data links over longer cable runs than single-ended logic interfaces, while RS-422 compatibility allows the same device to participate in compatible differential receiver networks. The SP485RCP-L provides a 1/1 driver-to-receiver configuration, allowing one transceiver to support bidirectional communication when the bus direction is controlled externally. Its 1 Mbps maximum signaling rate supports substantially faster communication than low-speed RS-485 devices. The commercial 0°C to 70°C temperature rating defines its intended operating environment, while the through-hole PDIP-8 package supports conventional PCB assembly and field-serviceable equipment. The transceiver separates the physical-layer data path from the digital logic interface used by a host controller. Direction control must be managed so that the driver and receiver do not contend on the bus. For half-duplex networks, the system commonly uses a receiver-enable or driver-enable signal to change the operating direction around a transmission request. Proper termination and biasing remain essential for dependable behavior on multidrop buses. Typical applications include industrial control links, instrument interfaces, point-of-sale equipment, building automation controllers, and factory data networks. The part is especially relevant when an existing board uses an 8-pin PDIP footprint and requires a direct RS-485/RS-422 interface upgrade without changing the mechanical layout. Its maximum data rate also suits moderate-speed supervisory and control channels rather than only slow telemetry links. Designers should verify logic thresholds, driver enable polarity, receiver fail-safe behavior, isolation needs, and bus-topology requirements before releasing a replacement design. A DIP package simplifies through-hole assembly, but it is larger than surface-mount alternatives. In long cables or noisy industrial environments, add appropriate transient protection, controlled grounding, and tested termination rather than relying on the transceiver alone for surge immunity. This page combines package, interface, temperature, and data-rate details with pin-compatible replacement guidance and practical PCB considerations. It is intended to help engineers determine whether SP485RCP-L fits an existing RS-485 design and to identify the checks required before approving a substitution.

RFQ İletişim
SP485REN-L - 5Mbps RS-485 Transceiver | MaxLinear | SOIC-8
SP485REN-L

SP485REN-L - 5Mbps RS-485 Transceiver | MaxLinear | SOIC-8

The MaxLinear SP485REN-L is a half-duplex RS-485 and RS-422 transceiver rated for data rates up to 5 Mbps and supplied in an 8-pin SOIC package. Its 1/10-unit-load receiver input enables more than 400 transceivers on one transmission line, while its 4.75 V to 5.25 V supply range supports conventional 5 V industrial communication systems. The SP485REN-L also provides high receiver input impedance, helping preserve the integrity of the driver signal when many nodes share a bus. An RS-485 transceiver is an interface IC that combines a differential line driver and differential receiver, allowing reliable bidirectional communication over long, electrically noisy interconnects. The SP485REN-L belongs to the RS-422/RS-485 interface hierarchy within the broader semiconductor and industrial-control markets. Its half-duplex architecture supports a shared differential pair through a direction-control input, making it suitable for multidrop buses, remote monitoring, factory automation, and building-control networks. The principal feature of the SP485REN-L is its low 1/10-unit-load receiver input. According to the manufacturer product information, this impedance permits more than 400 transceivers on a single transmission line without degrading the RS-485 driver signal. The device operates from a 4.75 V to 5.25 V supply, communicates at rates up to 5 Mbps, and supports an industrial temperature range of -40°C to 85°C. Its BiCMOS implementation combines low-power operation with high communication performance. The SP485REN-L uses a half-duplex arrangement in which the driver and receiver share differential bus terminals. A driver-enable control determines whether the device transmits, while a receiver-enable control determines whether the receiver is active. The high receiver impedance is particularly useful when numerous nodes must share one cable because it limits loading of the bus. This characteristic also distinguishes the SP485REN-L from the standard SP485 configuration for designs where node count is a primary constraint. Typical applications include industrial sensor networks, PLC-to-remote-I/O links, building automation equipment, telecommunications infrastructure, instrumentation, and industrial motor-control systems. A half-duplex implementation can connect a controller to distributed sensors over one twisted pair, while the 5 Mbps capability provides useful margin for moderate-speed industrial links and point-to-point backplanes. Designers should account for bus termination, fail-safe biasing, common-mode range, and cable length when integrating the transceiver. Place the transceiver close to the connector and route the differential pair as a balanced pair to minimize noise pickup. The external enable logic must also prevent driver contention, particularly during startup or fault-recovery conditions. This page combines device specifications, package and pin information, application guidance, drop-in alternatives, and practical interface-design considerations. It helps engineers compare bus loading, data rate, package compatibility, and protection requirements before assigning the SP485REN-L to a new RS-485 design.

RFQ İletişim
SP485REN-L/TR - 5V RS-485/RS-422 Transceiver | MaxLinear
SP485REN-L/TR

SP485REN-L/TR - 5V RS-485/RS-422 Transceiver | MaxLinear

The MaxLinear SP485REN-L/TR is a 5 V half-duplex differential bus transceiver supporting RS-485 and RS-422 interfaces in an 8-pin SOIC package. It operates from 4.75 V to 5.25 V, supports data rates up to 5 Mbps, and is specified as a 1/1-unit-load transceiver for industrial-temperature applications. The device combines a push-pull differential driver and differential receiver in one package, allowing a single pair of interface ICs to support bidirectional half-duplex communication. An RS-485 transceiver is an interface IC that converts logic-level digital signals into balanced differential signals for reliable communication over longer, potentially noisy industrial buses. It belongs to the RS-485 and RS-422 transceiver category, within interface ICs and the broader semiconductor hierarchy. The SP485REN-L/TR is intended for systems that need standardized differential signaling, bus arbitration behavior, and a compact surface-mount implementation. Key features include support for both RS-485 and RS-422 operation, a maximum signaling rate of 5 Mbps, operation from a single 4.75 V to 5.25 V supply, and a high-impedance receiver arrangement identified by the REN designation. MaxLinear describes the SP485 and SP483 families as BiCMOS products designed to reduce power consumption without sacrificing performance. The industrial-temperature option and lead-free SOIC-8 package suit compact industrial control, instrumentation, and communications equipment. The REN variant provides higher receiver input impedance than the standard SP485 arrangement. A comparative manufacturer-family listing identifies the SP485REN-L as suitable for connecting more than 400 transceivers on one transmission line without degrading the RS-485 driver signal. This characteristic is useful in large multi-drop installations where many receiver nodes share a common bus, although cable length, topology, termination, and transceiver loading must still be evaluated together. Typical applications include industrial sensor networks, factory automation equipment, building-control interfaces, process instrumentation, and RS-485-to-serial bridges. At high data rates, cable type, connector transitions, grounding, and electromagnetic compatibility become increasingly important. At lower rates, longer cable runs may be practical, subject to the propagation delay and differential resistance limits of the selected cable and network topology. Designers should use the pin-description table and typical application circuit in the manufacturer datasheet when assigning PCB traces. Place the transceiver close to the bus connector, provide a solid ground reference, route the differential pair as a balanced pair, and avoid adding unnecessary stubs. Power-supply decoupling should be placed near the device, while external protection should be selected for the cable length, installation environment, and required surge withstand. This page organizes the confirmed electrical, package, application, and sourcing information for SP485REN-L/TR and adds practical guidance for bus layout, protection, compliance review, and drop-in replacement assessment. It distinguishes documented pin-compatible options from functionally similar devices that may require design verification before substitution.

RFQ İletişim
SP485REP-L - 1/10 Unit Load RS-485 Transceiver | Exar
SP485REP-L

SP485REP-L - 1/10 Unit Load RS-485 Transceiver | Exar

Exar Corporation SP485REP-L is a half-duplex RS-485/RS-422 transceiver with a 1/10 unit-load receiver input, a 4.75 V to 5.25 V supply, and an 8-pin plastic DIP package. It supports more than 400 transceivers on one transmission line and provides a typical receiver input impedance of 150 kOhm. Its 60 ns propagation delay and operating-temperature range from -40 C to +85 C make it suitable for industrial multipoint data links. An RS-485 transceiver is an interface IC that combines a differential line driver and differential receiver, allowing equipment to communicate reliably over noisy, long cable runs. The half-duplex arrangement means the driver and receiver share the same differential pair, with direction controlled by the design. As a universal bus transceiver, the SP485REP-L belongs to the interface IC hierarchy: bus transceiver, line transceiver, physical-layer interface, and communication semiconductor. The principal feature is its 1/10 unit-load receiver input. A lower unit load reduces the loading placed on a shared bus, while the specified typical input resistance of 150 kOhm helps preserve driver signal integrity. The result is support for more than 400 transceivers on a single transmission line. Half-duplex operation also reduces wiring complexity by sharing one bus pair rather than requiring separate transmit and receive pairs. The device operates from a regulated 4.75 V to 5.25 V supply and includes a propagation delay of 60 ns, according to the published SP485REP-L specifications. Its 8-pin plastic DIP package is intended for through-hole assembly and prototyping rather than compact automated surface-mount production. The -40 C to +85 C operating range provides useful environmental headroom for industrial control, instrumentation, and communications equipment. Typical uses include RS-485 field buses, industrial sensor networks, building automation equipment, remote monitoring stations, and data-acquisition systems. The high receiver impedance is particularly useful when many nodes share the same two-wire bus. Compared with a 1/8 or 1/4 unit-load transceiver, the 1/10 unit-load rating provides lower bus loading, while the trade-off is that the exact replacement must still match supply voltage, driver and receiver ratings, enable logic, and DIP pin mapping. Designers should verify the manufacturer's pinout and termination requirements before layout, and should use a proper RS-485 line network with controlled stub lengths. The DIP footprint requires through-hole clearances and adequate lead-bend spacing. Because the verified data does not include detailed absolute-maximum ratings, driver output levels, or full timing tables, those values should be obtained from the manufacturer datasheet before final release. This page consolidates the verified 1/10 unit-load, impedance, voltage, delay, temperature, package, pricing-directory, and replacement information with application guidance and package-conscious comparisons. It distinguishes confirmed facts from parameters that still require datasheet confirmation, helping engineers shortlist the SP485REP-L without overlooking PCB or bus-compatibility constraints.

RFQ İletişim
SP490CN-L - 5Mbps RS-485/RS-422 Transceiver | MaxLinear
SP490CN-L

SP490CN-L - 5Mbps RS-485/RS-422 Transceiver | MaxLinear

The MaxLinear SP490CN-L is a low-power BiCMOS differential line transceiver with one driver and one receiver, supporting RS-485 and RS-422 operation up to 5 Mbps in an 8-pin SOIC package. Its key electrical features include ±200 mV receiver input sensitivity, a wide receiver common-mode range, and 5 V supply operation. The SP490 is designed for industrial data links where low-power differential signaling and reliable noise immunity are important. An RS-485/RS-422 transceiver is an interface IC that combines a differential line driver and differential receiver into one package. The driver converts a logic signal into a balanced differential transmission, while the receiver converts the differential pair back into a logic signal. This interface class belongs to the broader hierarchy of interface ICs, communication transceivers, and semiconductor signal-conditioning devices used in industrial control, instrumentation, and point-to-point data systems. The verified manufacturer material identifies the SP490 as a low-power BiCMOS RS-485/RS-422 transceiver capable of operation to 5 Mbps. The receiver sensitivity is specified as ±200 mV, and the family is available in 8-pin plastic DIP and NSOIC packages. The SP491 is a related family member with additional driver and receiver tri-state enable lines, but it is not an interchangeable substitute for every SP490 design because its control-pin arrangement differs. The SP490CN-L is suitable for industrial communication links, data acquisition equipment, instrumentation, and embedded control systems using differential buses. Its 5 V supply simplifies integration with conventional 5 V logic systems, while the differential interface helps reject common-mode noise on longer cable runs. Designers must still account for termination, biasing, grounding, and protection-network requirements in the complete RS-485 or RS-422 interface. For PCB implementation, place the transceiver close to the connector and route the differential pair as a controlled-impedance pair with minimal stub length. Keep the ground reference continuous under the interface, use appropriate surge protection for exposed cabling, and verify that the receiver remains enabled or disabled as required by the bus architecture. The SP490CN-L datasheet is the authoritative source for electrical limits, pin assignments, and package details.

RFQ İletişim
SP490CN-L/TR - 5Mbps RS-485/RS-422 Transceiver | MaxLinear (Tape & Reel)
SP490CN-L/TR

SP490CN-L/TR - 5Mbps RS-485/RS-422 Transceiver | MaxLinear (Tape & Reel)

The MaxLinear SP490CN-L/TR is a low-power BiCMOS differential line transceiver with one driver and one receiver, supporting RS-485 and RS-422 operation up to 5 Mbps in an 8-pin SOIC package. Its key electrical features include ±200 mV receiver input sensitivity, a wide receiver common-mode range, and 5 V supply operation. The SP490 is designed for industrial data links where low-power differential signaling and reliable noise immunity are important. An RS-485/RS-422 transceiver is an interface IC that combines a differential line driver and differential receiver into one package. The driver converts a logic signal into a balanced differential transmission, while the receiver converts the differential pair back into a logic signal. This interface class belongs to the broader hierarchy of interface ICs, communication transceivers, and semiconductor signal-conditioning devices used in industrial control, instrumentation, and point-to-point data systems. The verified manufacturer material identifies the SP490 as a low-power BiCMOS RS-485/RS-422 transceiver capable of operation to 5 Mbps. The receiver sensitivity is specified as ±200 mV, and the family is available in 8-pin plastic DIP and NSOIC packages. The SP491 is a related family member with additional driver and receiver tri-state enable lines, but it is not an interchangeable substitute for every SP490 design because its control-pin arrangement differs. The SP490CN-L/TR is suitable for industrial communication links, data acquisition equipment, instrumentation, and embedded control systems using differential buses. Its 5 V supply simplifies integration with conventional 5 V logic systems, while the differential interface helps reject common-mode noise on longer cable runs. Designers must still account for termination, biasing, grounding, and protection-network requirements in the complete RS-485 or RS-422 interface. For PCB implementation, place the transceiver close to the connector and route the differential pair as a controlled-impedance pair with minimal stub length. Keep the ground reference continuous under the interface, use appropriate surge protection for exposed cabling, and verify that the receiver remains enabled or disabled as required by the bus architecture. The SP490CN-L/TR datasheet is the authoritative source for electrical limits, pin assignments, and package details.

RFQ İletişim
SP490CS-L - 5Mbps RS-485/RS-422 Transceiver | MaxLinear
SP490CS-L

SP490CS-L - 5Mbps RS-485/RS-422 Transceiver | MaxLinear

The MaxLinear SP490CS-L is a low-power, full-duplex differential line-driver and receiver supporting RS-485 and RS-422 data rates up to 5 Mbps, supplied in an 8-pin plastic DIP package. It provides one transmitter and one receiver, operates from a 5 V supply, and has a typical supply current of 0.9 mA. The SP490 family provides ±200 mV receiver input sensitivity across a wide common-mode range, making it useful for robust industrial links where signal amplitude and ground-referred noise must be handled reliably. An RS-485 transceiver is an interface IC that combines a differential line driver and differential receiver for balanced digital communication. The SP490CS-L sits in the transceiver hierarchy alongside RS-422 interface devices, allowing the same physical network device to support both standards while providing noise rejection and differential signaling. Its full-duplex arrangement supports separate transmit and receive paths, and the manufacturer documentation identifies compatibility with commonly referenced LTC490 and SN75179-family interfaces. The main verified features are a 5 Mbps maximum data rate, 5 V supply operation, one-transmitter/one-receiver configuration, full duplex, ±200 mV receiver sensitivity, and low-power BiCMOS implementation. The source material states that the SP490 is available in 8-pin NSOIC packages, while the exact SP490CS-L distributor listing identifies an 8-pin plastic DIP package. The -L ordering suffix and package construction should therefore be checked against the manufacturer’s ordering information before production release. The device is appropriate for industrial automation, instrumentation, factory equipment, building controls, and other balanced serial links where RS-485 or RS-422 operation is required. In an RS-485 network, the differential outputs reduce sensitivity to common-mode noise compared with single-ended signaling, while the receiver threshold supports detection of relatively small differential voltages. The 5 Mbps capability allows the device to handle higher-speed short-distance links than a low-rate transceiver, although cable length, topology, termination, and transceiver count still determine practical network performance. Designers should preserve the differential pair geometry between the transceiver and connector, provide the required supply decoupling close to the device, and apply termination and biasing appropriate to the selected RS-485 or RS-422 topology. The receiver and driver paths are not the same as the SP491: the SP491 adds driver and receiver tri-state enable lines, whereas the SP490 does not. This distinction is important when replacing a part in a design that relies on bus disable or controlled tri-state behavior. This page consolidates verified manufacturer and distributor information, identifies package and interface details, separates sourced replacement evidence from unsupported assumptions, and highlights the design constraints that matter when selecting a 5 Mbps RS-485/RS-422 transceiver. The listed alternatives are limited to candidates supported by the supplied cross-reference evidence and are not intended to imply unreported electrical equivalence.

RFQ İletişim
SP490ECN-L - 10Mbps Full-Duplex RS-485 | MaxLinear
SP490ECN-L

SP490ECN-L - 10Mbps Full-Duplex RS-485 | MaxLinear

The MaxLinear SP490ECN-L is a low-power differential line driver and receiver implementing a full-duplex RS-485 and RS-422 interface at speeds up to 10Mbps in an 8-pin SOIC package. The device combines one differential driver and one differential receiver, ±200mV receiver input sensitivity, and a wide common-mode range for robust industrial communications. Its specified supply-voltage range is 4.75V to 5.25V. A differential line transceiver is an interface IC that converts logic-level signals into balanced differential transmissions and reconstructs digital data from differential receiver inputs. In the system hierarchy, it is an interface transceiver within RS-485 and RS-422 interface ICs. The full-duplex arrangement supports simultaneous transmission and reception, making it appropriate for point-to-point links where separate differential pairs are available. The SP490E family's principal features include operation up to 10Mbps, ±200mV receiver sensitivity, and operation from a 4.75V to 5.25V supply. The SP490ECN-L commercial-temperature ordering information identifies a 0°C to 70°C operating range. The 8-pin SOIC package supports conventional surface-mount assembly, while the low-power BiCMOS implementation is intended for low-power communications equipment. The receiver threshold and common-mode capability are central to its industrial usefulness. A ±200mV receiver sensitivity permits small differential signals to be recognized reliably, while the wide common-mode range helps the receiver tolerate voltage offsets between connected systems. The manufacturer datasheet also identifies the SP490 as compatible with the related SP491 family and indicates pin compatibility with the LTC490 for the SP490E family, enabling controlled design comparisons. Typical uses include full-duplex industrial RS-485 links, RS-422 point-to-point communications, factory equipment interfaces, data-acquisition equipment, and instrumentation systems. The 10Mbps capability supports higher-rate factory-bus traffic, while full duplex permits simultaneous bidirectional communication when the system provides both transmit and receive differential pairs. The primary design consideration is to maintain the transceiver's supply and bus requirements exactly as specified in the manufacturer datasheet. Layout should keep the driver and receiver connections associated with their intended differential pairs, provide a low-impedance supply path, and provide the bypassing required by the device data sheet. Bus termination, protection, and grounding must be selected for the cable length and environment rather than inferred solely from the 10Mbps headline rate. This page combines manufacturer specifications, distributor availability, verified cross-reference findings, package details, and engineering-oriented selection guidance. It also distinguishes true pin-compatible choices from related SP490E variants and identifies where additional design verification is still required before substitution.

RFQ İletişim
SP490ECN-L/TR - 10Mbps Full-Duplex RS-485 | MaxLinear (Tape & Reel)
SP490ECN-L/TR

SP490ECN-L/TR - 10Mbps Full-Duplex RS-485 | MaxLinear (Tape & Reel)

The MaxLinear SP490ECN-L/TR is a low-power differential line driver and receiver implementing a full-duplex RS-485 and RS-422 interface at speeds up to 10Mbps in an 8-pin SOIC package. The device combines one differential driver and one differential receiver, ±200mV receiver input sensitivity, and a wide common-mode range for robust industrial communications. Its specified supply-voltage range is 4.75V to 5.25V. A differential line transceiver is an interface IC that converts logic-level signals into balanced differential transmissions and reconstructs digital data from differential receiver inputs. In the system hierarchy, it is an interface transceiver within RS-485 and RS-422 interface ICs. The full-duplex arrangement supports simultaneous transmission and reception, making it appropriate for point-to-point links where separate differential pairs are available. The SP490E family's principal features include operation up to 10Mbps, ±200mV receiver sensitivity, and operation from a 4.75V to 5.25V supply. The SP490ECN-L/TR commercial-temperature ordering information identifies a 0°C to 70°C operating range. The 8-pin SOIC package supports conventional surface-mount assembly, while the low-power BiCMOS implementation is intended for low-power communications equipment. The receiver threshold and common-mode capability are central to its industrial usefulness. A ±200mV receiver sensitivity permits small differential signals to be recognized reliably, while the wide common-mode range helps the receiver tolerate voltage offsets between connected systems. The manufacturer datasheet also identifies the SP490 as compatible with the related SP491 family and indicates pin compatibility with the LTC490 for the SP490E family, enabling controlled design comparisons. Typical uses include full-duplex industrial RS-485 links, RS-422 point-to-point communications, factory equipment interfaces, data-acquisition equipment, and instrumentation systems. The 10Mbps capability supports higher-rate factory-bus traffic, while full duplex permits simultaneous bidirectional communication when the system provides both transmit and receive differential pairs. The primary design consideration is to maintain the transceiver's supply and bus requirements exactly as specified in the manufacturer datasheet. Layout should keep the driver and receiver connections associated with their intended differential pairs, provide a low-impedance supply path, and provide the bypassing required by the device data sheet. Bus termination, protection, and grounding must be selected for the cable length and environment rather than inferred solely from the 10Mbps headline rate. This page combines manufacturer specifications, distributor availability, verified cross-reference findings, package details, and engineering-oriented selection guidance. It also distinguishes true pin-compatible choices from related SP490E variants and identifies where additional design verification is still required before substitution.

RFQ İletişim
SP490ECN/TR - 5Mbps RS-485/RS-422 Transceiver | MaxLinear
SP490ECN/TR

SP490ECN/TR - 5Mbps RS-485/RS-422 Transceiver | MaxLinear

The MaxLinear SP490ECN/TR is a 5 Mbps RS-485/RS-422 differential line transceiver with one driver and one receiver, operating from a single 5 V supply in an 8-pin SOIC package. The device combines a differential bus driver and differential receiver with ±200 mV receiver input sensitivity and supports balanced differential signaling over extended cable distances. Its BiCMOS implementation provides low power consumption for industrial communications equipment. An RS-485/RS-422 interface transceiver is a semiconductor product category used to convert logic-level signals into balanced differential transmissions and to recover differential signals from noisy buses. Within the broader hierarchy, the SP490ECN/TR is an interface transceiver, a bus-line transceiver, and a communications interface IC designed for industrial data links. Balanced signaling improves noise immunity by representing each signal as a difference between two conductors rather than as a single-ended voltage. The SP490ECN/TR supports data rates up to 5 Mbps while maintaining the operating characteristics required by RS-422 and RS-485 networks. Its single 5 V supply simplifies interface design, and the ±200 mV receiver sensitivity permits operation with attenuated or electrically noisy differential signals. The one-driver, one-receiver arrangement supports full-duplex point-to-point RS-422 links and multidrop RS-485 applications. The manufacturer datasheet also identifies compatibility with LTC490 and SN75179 devices. The transceiver combines a low-power BiCMOS driver and receiver with differential bus connections. Its receiver converts the difference between the positive and negative bus inputs into a single-ended logic output, while the driver converts a differential logic input into a complementary bus output. The wide receiver common-mode range is specifically identified in the manufacturer datasheet, helping the device tolerate voltage offsets imposed by grounds, cable terminations, and installed equipment on an industrial bus. Typical applications include industrial factory automation, point-to-point telemetry links, building-control networks, RS-422 equipment interfaces, and RS-485 multidrop communications. The 5 Mbps maximum signaling rate supports moderate- and high-speed data transfer, while the 8-pin SOIC format supports compact, surface-mounted assemblies. The same electrical interface can also serve industrial sensors, remote I/O modules, data acquisition equipment, and communication links between controllers and peripheral equipment. Designers should preserve the transceiver's differential signal routing and provide correct bus biasing and termination. Power-supply decoupling should be placed close to the device, while the driver and receiver ground connection should remain compatible with the interface reference plane. Termination is required according to the selected RS-422 or RS-485 topology rather than being applied indiscriminately to every node. Cable length, node spacing, grounding, and common-mode limits must be evaluated together for reliable operation. This product page combines the verified MaxLinear datasheet, distributor availability, pricing evidence, pin information, and package details with practical interface-design guidance. It also distinguishes the SP490ECN/TR from related SP490E and SP490ECN-L/TR variants by data rate while identifying only same-package drop-in alternatives supported by the supplied manufacturer and cross-reference information.

RFQ İletişim
SP490ECP-L - 10Mbps Full-Duplex RS-485 IC | MaxLinear
SP490ECP-L

SP490ECP-L - 10Mbps Full-Duplex RS-485 IC | MaxLinear

The MaxLinear, Inc. SP490ECP-L is a 10 Mbps full-duplex RS-485/RS-422 differential line transceiver packaged in an 8-pin PDIP package. It combines one differential driver and one differential receiver, supports +5 V-only operation, and is intended for bidirectional serial data links that require simultaneous transmitting and receiving. The SP490E family is specified for operation at data rates up to 10 Mbps. An RS-485 transceiver is a physical-layer interface IC that converts logic-level signals into balanced differential signals for reliable communication over longer distances and in electrically noisy environments. Related classifications include differential line transceiver, communications interface IC, and interface IC. The SP490ECP-L supports both RS-485 and RS-422 applications while providing a +200 mV receiver input sensitivity and a wide common-mode range. The SP490E family is designed for low-power +5 V operation. Its single transmitter and single receiver support full-duplex links, while the SP490E family's differential signaling helps reject common-mode noise. The product is available in through-hole 8-pin PDIP packaging, which is useful for legacy industrial, telecommunications, instrumentation, and control equipment where surface-mount assembly is not required. According to the manufacturer product page, the SP490E meets RS-485 and RS-422 standards at speeds up to 10 Mbps. The receiver's stated sensitivity of ±200 mV defines the differential input range around which the receiver recognizes signaling states, while the wide common-mode range helps preserve operation where the two conductors experience voltage offsets relative to the local ground reference. Typical uses include industrial RS-485 buses, point-to-point RS-422 links, process-control equipment, data acquisition systems, and legacy communications equipment. Unlike a half-duplex transceiver, the full-duplex architecture can transmit and receive concurrently when the interface is wired with separate differential pairs, simplifying timing in applications that cannot stop receiving while the transmitter is active. The primary design consideration is that the 8-pin PDIP footprint does not itself guarantee interoperability with every RS-485 transceiver. Before substitution, engineers should verify pin assignments, driver and receiver enable behavior, supply requirements, common-mode limits, fail-safe response, and bus termination against the manufacturer datasheet and the original board schematic. This page consolidates verified distributor specifications, lifecycle information, pin-compatible alternatives, and application-oriented design guidance. It adds practical selection context beyond a distributor listing while keeping unverified electrical values clearly separated from the supplied source data.

RFQ İletişim
SP490EEN-L - 10Mbps RS-485/RS-422 Transceiver | MaxLinear
SP490EEN-L

SP490EEN-L - 10Mbps RS-485/RS-422 Transceiver | MaxLinear

The MaxLinear, Inc. SP490EEN-L is a low-power differential RS-485/RS-422 line transceiver rated for operation up to 10 Mbps, with a 4.75 V to 5.25 V supply range and an 8-pin narrow SOIC package. It provides a full-duplex differential bus interface with receiver input sensitivity of ±200 mV and a wide common-mode input range. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential line signals and receives differential signals back as digital logic. It belongs to the physical-layer hierarchy of communication components: transceiver, line driver and receiver, differential interface, interface IC, and integrated circuit. Balanced signaling improves noise immunity by coupling the intended signal differentially and rejecting common-mode voltage. The SP490EEN-L's principal features include a maximum data rate of 10 Mbps, operation from a 4.75 V to 5.25 V supply, and ±200 mV receiver sensitivity. Its low-power differential architecture is intended for industrial-control links, data-acquisition equipment, factory automation, and other systems that exchange reliable data over longer cable runs than a single-ended interface can support. The device combines a differential driver and differential receiver in one package. Differential transmission reduces sensitivity to ground-potential differences between connected equipment, while the receiver's ±200 mV threshold allows the communications system to tolerate noise and attenuation. The wide common-mode range is especially useful in industrial environments where ground offsets can occur between separately powered nodes. Typical uses include full-duplex industrial networks, programmable-logic-controller communication, motor-control interfaces, building-automation equipment, and instrumentation links. A full-duplex arrangement uses separate differential paths for transmission and reception, allowing the controller and peripheral to exchange information simultaneously without sharing a bus conductor. Designers should use a controlled-impedance PCB layout, terminate the transmission line appropriately at the far end, and provide local supply bypassing close to the IC. The 8-pin SOIC footprint simplifies assembly, but the layout must preserve the relationship between each differential pair and its return path. Cabling, grounding, and termination should be validated together because a compliant transceiver does not compensate for an incorrectly terminated cable. This page consolidates verified manufacturer specifications, distributor pricing, same-package replacement research, application guidance, and practical PCB considerations. It is designed to help engineers identify whether the SP490EEN-L fits a 5 V full-duplex RS-485 or RS-422 design without relying on incomplete distributor summaries alone.

RFQ İletişim
SP490EEN-L/TR - 10Mbps RS-485/RS-422 Transceiver | MaxLinear (Tape & Reel)
SP490EEN-L/TR

SP490EEN-L/TR - 10Mbps RS-485/RS-422 Transceiver | MaxLinear (Tape & Reel)

The MaxLinear, Inc. SP490EEN-L/TR is a low-power differential RS-485/RS-422 line transceiver rated for operation up to 10 Mbps, with a 4.75 V to 5.25 V supply range and an 8-pin narrow SOIC package. It provides a full-duplex differential bus interface with receiver input sensitivity of ±200 mV and a wide common-mode input range. An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential line signals and receives differential signals back as digital logic. It belongs to the physical-layer hierarchy of communication components: transceiver, line driver and receiver, differential interface, interface IC, and integrated circuit. Balanced signaling improves noise immunity by coupling the intended signal differentially and rejecting common-mode voltage. The SP490EEN-L/TR's principal features include a maximum data rate of 10 Mbps, operation from a 4.75 V to 5.25 V supply, and ±200 mV receiver sensitivity. Its low-power differential architecture is intended for industrial-control links, data-acquisition equipment, factory automation, and other systems that exchange reliable data over longer cable runs than a single-ended interface can support. The device combines a differential driver and differential receiver in one package. Differential transmission reduces sensitivity to ground-potential differences between connected equipment, while the receiver's ±200 mV threshold allows the communications system to tolerate noise and attenuation. The wide common-mode range is especially useful in industrial environments where ground offsets can occur between separately powered nodes. Typical uses include full-duplex industrial networks, programmable-logic-controller communication, motor-control interfaces, building-automation equipment, and instrumentation links. A full-duplex arrangement uses separate differential paths for transmission and reception, allowing the controller and peripheral to exchange information simultaneously without sharing a bus conductor. Designers should use a controlled-impedance PCB layout, terminate the transmission line appropriately at the far end, and provide local supply bypassing close to the IC. The 8-pin SOIC footprint simplifies assembly, but the layout must preserve the relationship between each differential pair and its return path. Cabling, grounding, and termination should be validated together because a compliant transceiver does not compensate for an incorrectly terminated cable. This page consolidates verified manufacturer specifications, distributor pricing, same-package replacement research, application guidance, and practical PCB considerations. It is designed to help engineers identify whether the SP490EEN-L/TR fits a 5 V full-duplex RS-485 or RS-422 design without relying on incomplete distributor summaries alone.

RFQ İletişim
SP490EEP-L - 10Mbps Full-Duplex RS-485/422 | MaxLinear
SP490EEP-L

SP490EEP-L - 10Mbps Full-Duplex RS-485/422 | MaxLinear

MaxLinear SP490EEP-L is a 1-transceiver, full-duplex RS-485 and RS-422 interface IC that supports differential data rates up to 10 Mbps and is supplied in an 8-pin plastic DIP package. The device combines one differential line driver and one differential line receiver on the same package, allowing bidirectional point-to-point communication without half-duplex bus-direction control. According to the MaxLinear SP490E/SP491E datasheet, the receiver input sensitivity is ±200 mV over a wide common-mode range. The SP490EEP-L is the SP490E full-duplex configuration; unlike SP491E devices, the SP490E does not provide separate driver and receiver tri-state enable inputs. This distinction makes the SP490EEP-L appropriate for RS-422 links and full-duplex RS-485 point-to-point or multipoint arrangements where the line state is managed by the surrounding system rather than local enable pins. The 8-PDIP format facilitates prototyping, legacy industrial control, and manually assembled systems where a through-hole package is easier to inspect and replace. Its low-power BiCMOS implementation supports low-power communication equipment while retaining the data rate required by industrial links, instrumentation, and embedded serial interfaces. The datasheet material also identifies compatibility with LTC490-class interfaces, but every replacement must be checked for enable behavior, supply requirements, receiver thresholds, and package-specific pin mapping before design release.

RFQ İletişim
SP490EN-L - 5Mbps RS-485/RS-422 Transceiver | MaxLinear
SP490EN-L

SP490EN-L - 5Mbps RS-485/RS-422 Transceiver | MaxLinear

The MaxLinear SP490EN-L is a low-power differential line transceiver supporting RS-485 and RS-422 communication at data rates up to 5 Mbps, with one transmitter and one receiver in an 8-pin narrow SOIC package. It operates from a 5 V supply, provides ±200 mV receiver input sensitivity, and is specified for commercial temperature operation from -40°C to +85°C. An RS-485/RS-422 transceiver is an interface IC that converts single-ended logic signals into differential signals for balanced wired communication and converts received differential signals back into logic-level data. The differential signal path improves noise immunity and allows communication across longer cable runs than ordinary single-ended interfaces. SP490EN-L sits within the interface-IC hierarchy as a bus transceiver for industrial, instrumentation, and data-communication equipment. The SP490EN-L combines one differential driver and one differential receiver in a full-duplex arrangement. Its low-power BiCMOS implementation is intended for 5 V systems and supports data rates up to 5 Mbps. The receiver sensitivity of ±200 mV helps recognize small differential signals, while the wide common-mode range allows useful operation in electrically noisy environments when the board and cabling are designed appropriately. The SP491 is identified by the datasheet as functionally similar but adds driver and receiver tri-state enable lines, so it is not used as a direct substitute here. Typical applications include RS-485 field-bus links, industrial control and test equipment, point-to-point RS-422 links, data acquisition systems, and communication links between separated circuit boards. The full-duplex arrangement is useful where transmit and receive paths must operate independently, although the SP490EN-L does not provide the explicit tri-state enable controls associated with SP491. Cable length and data rate must be selected together because transmission-line losses, termination, stub effects, and common-mode limits can reduce the usable cable distance. For PCB design, keep the differential pair impedance-controlled and route the driver and receiver connections according to the system’s cable and termination strategy. Place termination and protection components close to the transceiver pins, and verify that the selected protection network does not degrade the receiver’s differential sensitivity or data-rate margin. Power-supply bypassing should be placed directly beside the device supply pins. The verified data does not provide exact absolute maximum ratings, propagation-delay limits, receiver common-mode limits, or package dimensions, so those values should be taken from the MaxLinear datasheet before final design release.

RFQ İletişim