Ürünler (44.000+)

STM8L152K4T6 - 16MHz 16KB Flash Ultra-Low-Power MCU | STMicroelectronics
STM8L152K4T6

STM8L152K4T6 - 16MHz 16KB Flash Ultra-Low-Power MCU | STMicroelectronics

The STMicroelectronics STM8L152K4T6 is an 8-bit ultra-low-power microcontroller operating up to 16 MHz with 16 KB of Flash memory in a 32-pin LQFP 7 x 7 mm package. The device supports 2.5 V and 3.3 V operation and integrates 1 KB of data EEPROM, an LCD interface, real-time clock, timers, USART, I2C, SPI, ADC, DAC, and comparators. An ultra-low-power microcontroller is a compact embedded controller designed to maintain accurate digital control while minimizing energy use. The STM8L family belongs to the 8-bit microcontroller hierarchy and is intended for battery-powered, portable, industrial, sensing, and control products where low active and standby power can extend operating time between maintenance events. The STM8L152K4T6 combines that low-power positioning with a broad collection of mixed-signal and communications peripherals. Key features include 16 KB of Flash for firmware, 16 MHz maximum operating frequency, 1 KB of data EEPROM, and dedicated 2.5 V or 3.3 V supply operation. Integrated LCD support is useful in meter, keypad, and panel designs, while the RTC and low-power modes suit timekeeping applications. USART, I2C, and SPI interfaces provide practical options for sensors, transceivers, memory, and external controllers. The STM8L152K4T6 also integrates a 12-bit-class ADC, DAC, and comparators according to the family-level device description, allowing compact designs to perform analog measurement and control without requiring every conversion function in a separate IC. Its 32-pin LQFP package exposes the mixed-signal and digital resources required for medium-density embedded designs while remaining compatible with conventional leaded PCB assembly methods. Typical uses include low-energy sensor nodes, LCD utility meters, industrial condition-monitoring terminals, small appliance controllers, battery-powered instruments, and compact data-acquisition systems. The LCD interface, RTC, EEPROM, serial ports, ADC, DAC, and comparators make it especially useful when a single controller must combine display, measurement, timekeeping, and external communication. Designers should verify the exact pin configuration, operating limits, memory map, and peripheral electrical characteristics in the manufacturer datasheet before layout or production release. Production quantities also require board-level checks for decoupling, analog reference stability, LCD drive requirements, clock configuration, and low-power mode transitions. The verified distributor data supports availability and pricing references, but the available excerpts do not provide a complete timing, power-consumption, or absolute-maximum-rating table. This product page combines verified manufacturer and distributor information with practical purchasing, comparison, and design guidance. It distinguishes true same-package alternatives from broader functional alternatives and identifies unavailable technical details explicitly instead of estimating them.

RFQ İletişim
STM8L152K4U6 - 16MHz 8-Bit Ultra-Low-Power MCU | STMicroelectronics
STM8L152K4U6

STM8L152K4U6 - 16MHz 8-Bit Ultra-Low-Power MCU | STMicroelectronics

The STMicroelectronics STM8L152K4U6 is an 8-bit ultra-low-power microcontroller with a 16 MHz maximum clock, 16 KB of Flash memory, and a 32-pin UFQFPN package with an exposed pad, supplied in a tray. It belongs to the STM8L ultra-low-power family and integrates an RTC, LCD controller, timers, USART, I2C, SPI, ADC, DAC, and comparators. The device is designed for compact, low-energy embedded systems where a modest processing rate and broad peripheral integration are more important than high-bandwidth processing. An ultra-low-power microcontroller is a type of embedded controller optimized to minimize energy consumption during active operation, idle periods, and shutdown states. The STM8L family belongs to the broader hierarchy of 8-bit MCU, embedded controller, and semiconductor categories. STM8L152K4U6 devices combine an energy-conscious architecture with analog and digital peripherals, allowing a design to avoid adding separate interface, conversion, or timing components. Key features include a 16 MHz maximum operating frequency, 16 KB Flash, 1 KB data EEPROM, and 2.5 V or 3.3 V supply operation as identified by the verified distributor data. Integrated communication resources include USART, I2C, and SPI, while the analog subsystem includes an ADC, DAC, and comparators. The RTC and LCD controller support designs that must retain timekeeping or directly drive a low-power display without relying on a separate host processor. The STM8L architecture uses an 8-bit CISC-style microcontroller core and a modular peripheral arrangement. The verified source describes the STM8L152x4/6 family as part of the STM8L ultra-low-power 8-bit family. Because this product is specified as a 16 KB Flash device, firmware planning must be based on 16 KB rather than the larger memory capacity available to some family members. Exact RAM, current-consumption, accuracy, and absolute maximum ratings require confirmation in the manufacturer datasheet. Typical uses include battery-powered environmental sensors, compact industrial monitoring nodes, low-power instrument interfaces, LCD-based control panels, and portable measurement products. In these systems, the integrated ADC and comparators support local sensing, the serial interfaces support external sensors or data acquisition modules, and the RTC can provide time stamping or scheduled control functions without continuous external supervision. Design consideration: select decoupling and power-distribution components according to the manufacturer reference circuit, and verify the device's exact pin assignments before PCB layout because the verified excerpts do not provide a complete pin table. Do not infer that family members with different flash sizes, temperature grades, or package suffixes are interchangeable without checking their ordering information. The STM8L152K4U6 uses a 32-pin UFQFPN with an exposed pad, so land-pattern and thermal-via design must follow the official package drawing. This page consolidates the verified manufacturer and distributor excerpts, separates exact published facts from unresolved datasheet parameters, and identifies same-family alternatives with explicit engineering differences. It also provides comparison, sourcing, design, and selection guidance to reduce the risk of choosing an MCU based only on its displayed part number.

RFQ İletişim
STM8L152K6T3 - 16MHz 32KB Low-Power MCU | STMicroelectronics
STM8L152K6T3

STM8L152K6T3 - 16MHz 32KB Low-Power MCU | STMicroelectronics

STMicroelectronics STM8L152K6T3 is an 8-bit ultra-low-power STM8L EnergyLite microcontroller with a 16 MHz clock, 32 KB Flash memory, and a 32-LQFP 7 x 7 mm package. It combines 1 KB of data EEPROM with an RTC, LCD interface, timers, USART, I2C, SPI, ADC, DAC, and comparators in an energy-conscious 8-bit platform. An ultra-low-power microcontroller is designed to maintain accurate measurement, communication, and control functions while minimizing energy use during active operation and standby. The STM8L family belongs to the broader hierarchy of embedded MCU, microcontroller, and semiconductor devices. Low-power architecture is especially useful in battery-operated equipment where the time spent waiting for an event can dominate overall energy consumption. The STM8L152K6T3 provides 32 KB of Flash for program storage, 1 KB of EEPROM for nonvolatile data, and operation from 1.8 V to 3.6 V. Its peripheral set includes an RTC for timekeeping, an ADC and comparators for analog measurements, a DAC for analog output, and USART, I2C, and SPI interfaces for external sensors, memory, and host connectivity. The LCD interface supports compact user-interface designs. This is a CISC-based 8-bit MCU built for compact embedded systems rather than high-throughput applications. Its 16 MHz operating frequency supports control-loop and communications tasks while its low-power operating modes help reduce average consumption. The medium-density STM8L15x family is specified over 1.8 V to 3.6 V and includes temperature grades from -40 °C to +85 °C and -40 °C to +125 °C depending on the exact ordering code. Typical applications include low-power sensor nodes, compact industrial monitoring equipment, battery-powered instruments, LCD-driven user interfaces, data loggers, and connected control modules. The ADC and comparators suit threshold detection, while the RTC and EEPROM can retain timestamps and calibration data between power cycles. Serial interfaces allow the MCU to connect measurement hardware to a host or external memory. Design around the MCU's low-power modes by defining which peripherals can remain active in each operating mode. Keep analog and communication traces short, provide the decoupling required by the manufacturer datasheet, and confirm pin multiplexing before assigning LCD, ADC, DAC, or serial functions. Verify the selected ordering code against the required temperature grade and production design. This product page combines the principal device specifications with package guidance, pinout-status documentation, selection trade-offs, and a focused comparison with same-family drop-in options. It is intended to help engineers evaluate memory, voltage, interface, and temperature requirements before committing the STM8L152K6T3 to a PCB design.

RFQ İletişim
STM8L152K6T6 - 16MHz 32KB Ultra-Low-Power MCU | STMicroelectronics
STM8L152K6T6

STM8L152K6T6 - 16MHz 32KB Ultra-Low-Power MCU | STMicroelectronics

STMicroelectronics STM8L152K6T6 is an 8-bit ultra-low-power microcontroller with a 16 MHz core, 32 KB of Flash memory, and 1 KB of data EEPROM in a 32-pin LQFP package measuring 7 x 7 mm. It belongs to the STM8L ultra-low-power 8-bit microcontroller family and is designed for compact, battery-operated systems that require broad peripheral support and low-power operation. An ultra-low-power microcontroller is an embedded processing device optimized to minimize energy consumption during active operation, idle periods, and shutdown states. Within the product hierarchy, the STM8L152K6T6 is a low-power MCU, a type of microcontroller and embedded semiconductor. Its combination of 16 MHz processing speed, serial interfaces, analog converters, and embedded timers allows one device to supervise sensors, control actuators, communicate with external circuits, and manage power in space-constrained equipment. Key features include 32 KB Flash, 1 KB data EEPROM, an LCD interface, real-time clock capability, timers, USART, I2C, SPI, ADC, DAC, and comparators. The operating supply range extends from 3.6 V down to V at power-down according to the manufacturer product information, while the maximum operating temperature reaches 125 °C. These features support applications spanning industrial controls, battery-powered instruments, metering equipment, consumer products, and compact sensing nodes. The STM8L152 architecture integrates an 8-bit core with dedicated analog and communication peripherals, reducing the need for external components in typical embedded designs. USART supports serial communication, I2C and SPI permit connection to sensors and memories, the ADC and DAC provide analog signal handling, and comparators support threshold-based decisions. The LCD interface and real-time clock are useful in instruments that display local information or maintain timekeeping while operating from constrained energy budgets. Typical applications include low-power industrial sensors, smart metering equipment, compact control panels, portable measurement products, and battery-operated monitoring devices. Its 32-pin LQFP package is suitable for conventional surface-mount assembly and provides access to the mixed analog, digital, and communication resources of the STM8L152 family. The combination of Flash, EEPROM, RTC, LCD, and serial peripherals can reduce board count compared with designs using several discrete controllers. When laying out a design, place decoupling capacitors close to the supply and ground pins, keep analog inputs short and away from fast-switching signals, and confirm the MCU operating mode against the system power budget. Use the manufacturer pin-definition table to assign every 32-pin LQFP connection, especially reset, oscillator, programming, and power pins. Validation should include startup, sleep-mode current, ADC accuracy, LCD timing, and communication behavior across the intended supply and temperature range. This page organizes the STM8L152K6T6 specification set, practical application fit, package information, and verified same-family alternatives into a design-focused reference. It also highlights the distinctions that matter when evaluating drop-in choices, including memory configuration, LCD support, interface coverage, and the effect of temperature-grade ordering codes.

RFQ İletişim
STM8L152K6U6 - 16MHz 32KB Ultra-Low-Power MCU | STMicroelectronics
STM8L152K6U6

STM8L152K6U6 - 16MHz 32KB Ultra-Low-Power MCU | STMicroelectronics

The STMicroelectronics STM8L152K6U6 is an ultra-low-power 8-bit microcontroller with a 16 MHz maximum clock, 32 KB of Flash memory, and a 32-pin UFQFPN package measuring 5 mm by 5 mm. It belongs to the STM8L ultra-low-power family and is designed for energy-sensitive embedded control applications that require a compact microcontroller and a broad peripheral set. An ultra-low-power 8-bit microcontroller is a compact embedded-control platform designed to consume little energy while performing sensor reading, timing, communications, data acquisition, and local control functions. The STM8L family hierarchy connects this device to 8-bit microcontrollers, embedded controllers, and semiconductor components suited to battery-operated, industrial, and always-on equipment. Its small package also supports space-constrained designs. The verified product information identifies 32 KB of Flash, operation up to 16 MHz, and an STM8L152K6-class configuration in a 32-pin UFQFPN package. The product family also provides LCD support, timers, USART, I2C, SPI, ADC, DAC, and comparators according to the supplied datasheet search result. These interfaces make the device suitable for connected sensing, low-power instrumentation, and compact control panels. The STM8L152K6U6 combines an 8-bit CPU architecture with a broad set of embedded peripherals rather than relying on external interface devices. Timer resources can support periodic measurement and PWM generation, while the ADC and comparators can monitor analog inputs. USART, I2C, and SPI options permit integration with sensors, transceivers, memory, and human-interface modules. The 32 KB Flash capacity provides room for application firmware and configuration data. Typical uses include low-energy sensor nodes, compact environmental monitors, LCD-driven utility meters, industrial condition-monitoring equipment, and battery-powered accessories. In each case, the device can consolidate several small functions into one controller while keeping the board area limited by the 5 mm by 5 mm package. Designers must still verify operating limits, peripheral availability, and pin multiplexing against the complete manufacturer documentation. The principal design consideration is package and pin planning. A 32-pin UFQFPN footprint requires careful escape routing, exposed-pad thermal management where applicable, and reflow-profile control. Exact pin names, alternate functions, and electrical limits are not included in the supplied verified excerpts, so they should not be inferred from generic STM8 family diagrams before the complete manufacturer datasheet and package drawing are reviewed. This page consolidates the verified distributor and manufacturer information, package details, interface capabilities, pricing references, and constrained drop-in alternatives. It also identifies where complete electrical, pinout, lifecycle, and compliance data remain necessary for production qualification rather than presenting unverified values as specifications.

RFQ İletişim
STM8L152K6U6TR - 16MHz 32KB Ultra-Low-Power MCU | STMicroelectronics (Tape & Reel)
STM8L152K6U6TR

STM8L152K6U6TR - 16MHz 32KB Ultra-Low-Power MCU | STMicroelectronics (Tape & Reel)

The STMicroelectronics STM8L152K6U6TR is an ultra-low-power 8-bit microcontroller with a 16 MHz maximum clock, 32 KB of Flash memory, and a 32-pin UFQFPN package measuring 5 mm by 5 mm. It belongs to the STM8L ultra-low-power family and is designed for energy-sensitive embedded control applications that require a compact microcontroller and a broad peripheral set. An ultra-low-power 8-bit microcontroller is a compact embedded-control platform designed to consume little energy while performing sensor reading, timing, communications, data acquisition, and local control functions. The STM8L family hierarchy connects this device to 8-bit microcontrollers, embedded controllers, and semiconductor components suited to battery-operated, industrial, and always-on equipment. Its small package also supports space-constrained designs. The verified product information identifies 32 KB of Flash, operation up to 16 MHz, and an STM8L152K6-class configuration in a 32-pin UFQFPN package. The product family also provides LCD support, timers, USART, I2C, SPI, ADC, DAC, and comparators according to the supplied datasheet search result. These interfaces make the device suitable for connected sensing, low-power instrumentation, and compact control panels. The STM8L152K6U6TR combines an 8-bit CPU architecture with a broad set of embedded peripherals rather than relying on external interface devices. Timer resources can support periodic measurement and PWM generation, while the ADC and comparators can monitor analog inputs. USART, I2C, and SPI options permit integration with sensors, transceivers, memory, and human-interface modules. The 32 KB Flash capacity provides room for application firmware and configuration data. Typical uses include low-energy sensor nodes, compact environmental monitors, LCD-driven utility meters, industrial condition-monitoring equipment, and battery-powered accessories. In each case, the device can consolidate several small functions into one controller while keeping the board area limited by the 5 mm by 5 mm package. Designers must still verify operating limits, peripheral availability, and pin multiplexing against the complete manufacturer documentation. The principal design consideration is package and pin planning. A 32-pin UFQFPN footprint requires careful escape routing, exposed-pad thermal management where applicable, and reflow-profile control. Exact pin names, alternate functions, and electrical limits are not included in the supplied verified excerpts, so they should not be inferred from generic STM8 family diagrams before the complete manufacturer datasheet and package drawing are reviewed. This page consolidates the verified distributor and manufacturer information, package details, interface capabilities, pricing references, and constrained drop-in alternatives. It also identifies where complete electrical, pinout, lifecycle, and compliance data remain necessary for production qualification rather than presenting unverified values as specifications.

RFQ İletişim
STM8L152M8T3 - 16MHz 64KB Low-Power MCU | ST
STM8L152M8T3

STM8L152M8T3 - 16MHz 64KB Low-Power MCU | ST

The STMicroelectronics STM8L152M8T3 is an 8-bit ultra-low-power microcontroller with a 16 MHz core, 64 KB of Flash program memory, LCD support, and an 80-pin LQFP package measuring 14 mm by 14 mm. It belongs to the STM8L15xx6/8 low-power MCU family and is suited to embedded systems that require compact size, low-power operation, and broad peripheral integration. An ultra-low-power microcontroller is an embedded controller designed to minimize energy consumption during active operation, standby, and low-power modes. Within the product hierarchy, the STM8L152M8T3 is a low-power MCU, an 8-bit microcontroller, and a semiconductor integrated circuit. The STM8 CPU core supports compact control firmware while integrated communication, timing, analog, and LCD-related resources reduce the need for external components. Verified device attributes include an 8-bit architecture, operation up to 16 MHz, 64 KB of Flash memory organized as 64K by 8 bits, LCD capability, and an 80-pin gull-wing LQFP package. The device also appears with an automotive temperature-grade designation in distributor technical listings. Its 14 mm by 14 mm LQFP package provides 80 accessible leads for analog, digital, communications, clock, debug, and power functions. The STM8L152M8T3 combines an embedded CPU with resources normally distributed across several discrete components. This integration is valuable when board area, standby consumption, and firmware complexity are important constraints. Exact RAM capacity, operating-voltage limits, individual peripheral ranges, clock-tree details, and converter performance should be confirmed against the manufacturer datasheet before a production schematic is released. Typical applications include low-energy sensor and metering systems, compact industrial controllers, battery-operated instruments, LCD human-interface panels, low-power communication equipment, and embedded control modules. The 64 KB Flash capacity supports moderate control code, while the large LQFP package exposes substantially more pins than smaller MCU packages for analog and mixed-signal assignments. Designers should assign every power, ground, decoupling, reset, and debug connection directly from the manufacturer pin-description table. Because this package has 80 leads, manual schematic review is particularly important; verify boot configuration, unused-pin treatment, oscillator connections, and programming access before PCB release. This product page consolidates manufacturer and distributor information with application guidance, procurement questions, comparison criteria, and design checks that support an engineering decision. The Request a Quote form on this page provides current commercial terms, stock status, and lead-time information without embedding stale pricing into the technical content.

RFQ İletişim
STM8L152M8T6 - 16MHz 64KB Low-Power MCU | ST
STM8L152M8T6

STM8L152M8T6 - 16MHz 64KB Low-Power MCU | ST

The STMicroelectronics STM8L152M8T6 is an 8-bit STM8L EnergyLite ultra-low-power microcontroller with a 16 MHz maximum CPU frequency, 64 KB of embedded Flash memory, 2 KB of data EEPROM, and an 80-pin LQFP package measuring 14 x 14 mm. It integrates an RTC, LCD support, timers, and an enhanced STM8 CPU core, making it suitable for compact control systems where energy efficiency and peripheral integration are important. An ultra-low-power microcontroller is a semiconductor designed to complete control, measurement, and communication tasks while minimizing energy consumption during active operation, standby, and low-power states. The STM8L152M8T6 belongs to the STM8L family, combining a CISC-based STM8 core with embedded Flash and EEPROM in a surface-mount package. This hierarchy places it between general-purpose 8-bit microcontrollers and highly integrated embedded control devices. Key features include a maximum CPU frequency of 16 MHz, an 8-bit data bus, 64 KB of programmable Flash, and 2 KB of data EEPROM. The integrated RTC supports timekeeping-oriented designs, while LCD support reduces the component count of segmented human-interface panels. The STM8L152M8 series also provides dedicated timer resources, allowing the MCU to measure intervals, generate timing signals, and coordinate periodic system functions without an external timing IC. The enhanced STM8 CPU core provides increased processing power compared with earlier low-power members of the STM8 family, with operation up to 16 MHz. The device combines 64 KB Flash with a separate 2 KB EEPROM area for persistent data. Its 80-LQFP package provides a large pin count relative to the device footprint, supporting extensive peripheral routing while remaining compatible with standard surface-mount assembly. Operating voltage, RAM capacity, and detailed temperature limits are not stated in the supplied source data and should be confirmed in the manufacturer documentation before design release. Typical applications include low-power sensor-hub controllers, battery-operated instruments, industrial monitoring nodes, LCD-based user interfaces, real-time-clock systems, and compact embedded products that require more I/O than a small-package MCU can offer. The combination of 64 KB Flash, 16 MHz processing speed, EEPROM, RTC, LCD support, and timers allows a single device to consolidate several peripheral functions. Designers should confirm the complete pin assignment, supply-voltage limits, decoupling requirements, and low-power configuration strategy against the manufacturer datasheet before PCB release. Because the LQFP footprint contains 80 fine-pitch leads, board assembly should provide suitable land patterns, thermal-via strategy, and soldering profiles. Firmware must also validate the active, standby, and wake-up behavior required by the final power budget. This page consolidates verified manufacturer and distributor information, source-linked pricing, same-package alternatives, comparison parameters, and practical selection guidance. It is intended to accelerate engineering review while clearly identifying parameter areas that still require datasheet confirmation.

RFQ İletişim
STM8L152M8T6TR - 16MHz 64KB Low-Power MCU | ST (Tape & Reel)
STM8L152M8T6TR

STM8L152M8T6TR - 16MHz 64KB Low-Power MCU | ST (Tape & Reel)

The STMicroelectronics STM8L152M8T6TR is an 8-bit STM8L EnergyLite ultra-low-power microcontroller with a 16 MHz maximum CPU frequency, 64 KB of embedded Flash memory, 2 KB of data EEPROM, and an 80-pin LQFP package measuring 14 x 14 mm. It integrates an RTC, LCD support, timers, and an enhanced STM8 CPU core, making it suitable for compact control systems where energy efficiency and peripheral integration are important. An ultra-low-power microcontroller is a semiconductor designed to complete control, measurement, and communication tasks while minimizing energy consumption during active operation, standby, and low-power states. The STM8L152M8T6TR belongs to the STM8L family, combining a CISC-based STM8 core with embedded Flash and EEPROM in a surface-mount package. This hierarchy places it between general-purpose 8-bit microcontrollers and highly integrated embedded control devices. Key features include a maximum CPU frequency of 16 MHz, an 8-bit data bus, 64 KB of programmable Flash, and 2 KB of data EEPROM. The integrated RTC supports timekeeping-oriented designs, while LCD support reduces the component count of segmented human-interface panels. The STM8L152M8 series also provides dedicated timer resources, allowing the MCU to measure intervals, generate timing signals, and coordinate periodic system functions without an external timing IC. The enhanced STM8 CPU core provides increased processing power compared with earlier low-power members of the STM8 family, with operation up to 16 MHz. The device combines 64 KB Flash with a separate 2 KB EEPROM area for persistent data. Its 80-LQFP package provides a large pin count relative to the device footprint, supporting extensive peripheral routing while remaining compatible with standard surface-mount assembly. Operating voltage, RAM capacity, and detailed temperature limits are not stated in the supplied source data and should be confirmed in the manufacturer documentation before design release. Typical applications include low-power sensor-hub controllers, battery-operated instruments, industrial monitoring nodes, LCD-based user interfaces, real-time-clock systems, and compact embedded products that require more I/O than a small-package MCU can offer. The combination of 64 KB Flash, 16 MHz processing speed, EEPROM, RTC, LCD support, and timers allows a single device to consolidate several peripheral functions. Designers should confirm the complete pin assignment, supply-voltage limits, decoupling requirements, and low-power configuration strategy against the manufacturer datasheet before PCB release. Because the LQFP footprint contains 80 fine-pitch leads, board assembly should provide suitable land patterns, thermal-via strategy, and soldering profiles. Firmware must also validate the active, standby, and wake-up behavior required by the final power budget. This page consolidates verified manufacturer and distributor information, source-linked pricing, same-package alternatives, comparison parameters, and practical selection guidance. It is intended to accelerate engineering review while clearly identifying parameter areas that still require datasheet confirmation.

RFQ İletişim
STM8L152M8T7 - 16MHz 8-Bit 64KB Ultra-Low-Power MCU | ST
STM8L152M8T7

STM8L152M8T7 - 16MHz 8-Bit 64KB Ultra-Low-Power MCU | ST

The STMicroelectronics STM8L152M8T7 is an 8-bit ultra-low-power microcontroller with a 16 MHz enhanced STM8 CPU core, 64 KB of embedded Flash memory, and an 80-LQFP package measuring 14 x 14 mm. The device targets compact, low-energy embedded systems that require substantial on-chip program memory, LCD-compatible peripherals, and a broad set of low-power operating modes. An ultra-low-power microcontroller is an integrated control device designed to minimize energy consumption during active operation, idle periods, and standby states. The STM8L152 belongs to the STM8L15xx low-power family, combining a simple 8-bit architecture with peripheral integration intended for battery-operated meters, sensing instruments, access controls, and human-machine-interface equipment. Its hierarchy extends from MCU to embedded processor, embedded controller, and semiconductor. Key features include a maximum clock frequency of 16 MHz, 64 KB of Flash program storage organized as 64K x 8, and an 80-pin LQFP package with a 14 x 14 mm body size. The STM8L152M8 family provides LCD-oriented connectivity together with ultra-low-power capabilities, making it suitable for designs in which the display, sensing, and control functions must operate from a constrained energy budget. The enhanced STM8 core provides a straightforward execution model for firmware that performs protocol handling, state management, sensor acquisition, and display updates. Because the device is an 8-bit MCU rather than a 32-bit application processor, designers should budget instruction cycles carefully for interrupt-heavy work, while still benefiting from the integrated Flash and low-power peripherals for compact embedded control tasks. Typical applications include battery-powered LCD instruments, environmental monitoring nodes, building-access terminals, simple metering systems, industrial panels, and low-energy sensor controllers. In each case, the STM8L152M8T7 is useful when the design benefits from the 64 KB program memory and LCD support while avoiding the overhead of a higher-performance processor. A critical design consideration is that software timing, interrupt priorities, and peripheral clock requirements must be configured for the STM8 architecture. Existing STM8L152M8 firmware can generally be reused across compatible family members, but changes in temperature grade, package suffix, or device variant should be checked against the pin-definition and electrical tables in the manufacturer datasheet before substitution. This page consolidates the confirmed device identity, package information, family positioning, drop-in alternatives, application guidance, and PCB implementation notes so that engineers can evaluate the STM8L152M8T7 before committing a PCB layout or production BOM.

RFQ İletişim
STM8L152R6T6 - 16MHz 32KB Ultra-Low-Power MCU | STMicroelectronics
STM8L152R6T6

STM8L152R6T6 - 16MHz 32KB Ultra-Low-Power MCU | STMicroelectronics

The STMicroelectronics STM8L152R6T6 is an 8-bit ultra-low-power microcontroller with a 16 MHz enhanced STM8 CPU core, 32 KB of Flash memory, and a 64-LQFP 10 x 10 mm package. It combines low-power operation with integrated RTC, LCD, timers, USART, I2C, SPI, ADC, DAC, and comparator resources for energy-conscious embedded designs. An ultra-low-power microcontroller, or ULP MCU, is a semiconductor that prioritizes low current consumption while retaining the peripherals and processing capability needed for compact embedded products. The STM8L152 family belongs to the STM8L EnergyLite product line and can sit within an embedded control system that measures, controls, communicates, and manages power without requiring a high-performance processor. Key features include up to 16 MHz processing performance, 32 KB Flash organized as 32K x 8, and a 16 MHz operating specification reported by the product listing. The device also supports an operating power supply down to 3.6 V in power-down operation, operation up to 125°C according to the component specification listing, and multiple serial and analog peripherals for reducing external component count. The STM8L152R6T6 uses the enhanced STM8 8-bit architecture and is designed for applications where energy efficiency, fast wake-up, and integrated mixed-signal resources matter more than a large memory map. Its peripheral set includes an RTC for timekeeping, LCD support for human-machine interfaces, USART and I2C for serial communication, SPI for higher-speed peripheral links, and ADC, DAC, and comparator resources for sensor and control circuits. Typical applications include low-energy sensor nodes, compact industrial monitors, building and access controls, battery-operated instruments, LCD-based meters, smart home endpoints, and portable measurement equipment. The 64-LQFP package also provides enough pins for external memory, display connections, communications, and analog inputs when required by a compact industrial design. When laying out the circuit, follow the manufacturer pin-description and package-connection tables rather than inferring unused pins. Place decoupling capacitors close to the supply pins, keep sensitive analog and digital return paths controlled, and verify startup, reset, clock, and power-down behavior against the device's configuration. The mixed supply limits shown across operating modes should be checked for every rail in the final power tree. This product page consolidates the exact STM8L152R6T6 identity, package and memory details, drop-in candidates, comparison parameters, and practical design guidance. It supports faster engineering decisions by connecting the device's low-power architecture and peripheral inventory to concrete embedded applications while keeping unresolved electrical details explicit rather than inferred.

RFQ İletişim
STM8L152R8T3 16MHz 64KB 64-LQFP Ultra-Low-Power MCU | STMicroelectronics
STM8L152R8T3

STM8L152R8T3 16MHz 64KB 64-LQFP Ultra-Low-Power MCU | STMicroelectronics

The STMicroelectronics STM8L152R8T3 is an ultra-low-power 8-bit STM8L EnergyLite microcontroller with a 16 MHz enhanced STM8 CPU core, 64 KB of Flash memory, LCD support, and a 64-LQFP 10x10 mm package. Its operating supply range is 1.65 V to 3.6 V without brown-out reset and 1.8 V to 3.6 V with brown-out reset, making it suitable for low-voltage embedded control systems. An ultra-low-power microcontroller is designed to maintain reliable digital control while minimizing energy consumption during standby, sleep, and active operation. The STM8L152R8T3 belongs to the STM8L family, combining an 8-bit CISC architecture, compact Flash-based program memory, LCD-oriented peripherals, and low-voltage operation in a surface-mount package. This combination makes it useful for compact battery-powered instruments, meter interfaces, sensor controllers, and embedded user-interface systems. The device is identified as an STM8L152R8 variant with 64 KB of Flash organized as 64K x 8 bits and a maximum stated CPU frequency of 16 MHz. Its LCD capability allows a system to drive segment or matrix displays without requiring a separate display controller. The 1.65 V to 3.6 V operating range also supports designs operating from single-cell lithium energy sources regulated to low-voltage rails, although the final power architecture must include appropriate battery protection. The STM8L152R8T3 is packaged in a 64-LQFP 10x10 mm form factor. This relatively high pin count supports a broad set of general-purpose and application-specific connections while remaining compatible with leaded-package assembly and inspection processes. The STM8L152R8 family is also available in several density and temperature configurations, so firmware validation must confirm that the selected ordering code matches the required memory, package, and operating-temperature grade. Typical uses include compact energy meters, sensor-hub boards, handheld measurement products, industrial panel controllers, and battery-operated instruments with LCD feedback. Because the MCU is designed for low-voltage systems, careful attention to supply noise, brown-out behavior, reset conditions, and peripheral current consumption is important during hardware development. For PCB design, place the MCU close to its supporting crystal or timing components and route sensitive inputs away from switching nodes. Use the manufacturer pin-description table when assigning every LQFP connection, and verify the exposed programming and debug functions before finalizing the footprint. Firmware should be tested across the intended supply range and temperature grade rather than relying only on nominal-room-temperature behavior. This product page consolidates the available manufacturer and distributor information, identifies the core electrical and packaging constraints, and provides practical selection guidance for engineers evaluating the STM8L152R8T3 in low-power LCD-equipped embedded designs.

RFQ İletişim
STM8L152R8T6 - 8-Bit Ultra-Low-Power MCU, 64KB Flash | STMicroelectronics
STM8L152R8T6

STM8L152R8T6 - 8-Bit Ultra-Low-Power MCU, 64KB Flash | STMicroelectronics

The STM8L152R8T6 is an 8-bit ultra-low-power microcontroller from STMicroelectronics, part of the STM8L EnergyLite family. It features an enhanced STM8 CPU core running at up to 16 MHz, 64 KB of Flash memory, 4 KB of RAM, and 2 KB of data EEPROM. The device is housed in a 64-pin LQFP (10x10 mm) package and operates over a supply voltage range of 1.8V to 3.6V, with a temperature range of -40°C to 125°C. It integrates a rich set of peripherals including an LCD driver, real-time clock (RTC), timers, USART, I2C, SPI, ADC, DAC, and comparators, making it suitable for a wide range of low-power applications. An 8-bit microcontroller is a single-chip computer with an 8-bit data bus, typically used in embedded systems where cost, power efficiency, and simplicity are prioritized over raw processing power. The STM8L152R8T6 belongs to the STM8L series, which is specifically designed for ultra-low-power operation, featuring multiple low-power modes (Wait, Low-power Run, Low-power Wait, Active-halt, and Halt) to minimize energy consumption. In the broader hierarchy, it sits as a microcontroller -> 8-bit MCU -> ultra-low-power MCU -> STM8L EnergyLite family, and is a key component in battery-powered and energy-harvesting applications. Key features include an ultra-low-power STM8 core with up to 16 MHz operation, 64 KB Flash with read-while-write capability, 4 KB RAM, 2 KB true data EEPROM with error correction code (ECC), and a 12-bit ADC with up to 28 channels. The device also integrates a 12-bit DAC, two comparators, an LCD driver supporting up to 8x40 segments, and a real-time clock with calendar and alarm functions. Its low-power design achieves typical current consumption of 3.4 µA in Halt mode with RTC on, and 0.35 µA in Halt mode without RTC, making it ideal for battery-powered devices. From a technical depth perspective, the STM8L152R8T6 uses a Harvard architecture with a 3-stage pipeline, allowing most instructions to execute in a single clock cycle. The Flash memory supports read-while-write, enabling firmware updates without halting the CPU. The device includes a flexible clock system with internal and external oscillators, a phase-locked loop (PLL) for frequency multiplication, and a clock security system for fail-safe operation. The ultra-low-power design is achieved through advanced process technology and multiple power domains, allowing independent power management of the core, peripherals, and I/O. Typical applications include portable medical devices (e.g., glucose meters, pulse oximeters), smart meters, wireless sensor nodes, and industrial control systems. The STM8L152R8T6's low power consumption and rich analog peripherals make it particularly well-suited for battery-powered applications where long battery life is critical. Its LCD driver and RTC also make it ideal for consumer electronics like digital thermometers and smart watches. When designing with this device, pay careful attention to the power supply decoupling: place a 100 nF capacitor close to each VDD pin and a 1 µF capacitor at the main power input. Additionally, configure the unused I/O pins to analog mode or low-power mode to minimize leakage current, and use the low-power modes effectively to extend battery life.

RFQ İletişim
STM8L162M8T6 - 8-Bit Ultra-Low-Power MCU, 64KB Flash | STMicroelectronics
STM8L162M8T6

STM8L162M8T6 - 8-Bit Ultra-Low-Power MCU, 64KB Flash | STMicroelectronics

The STM8L162M8T6 is an 8-bit ultra-low-power microcontroller from STMicroelectronics' STM8L EnergyLite family. It features a 16 MHz STM8 core, 64 KB of Flash memory, 4 KB of RAM, and 68 I/O pins in an 80-pin LQFP package (14x14 mm). Operating from 1.8V to 3.6V, it is designed for energy-efficient applications requiring long battery life. An 8-bit microcontroller (MCU) is a single-chip computer with an 8-bit data bus, executing instructions sequentially. It integrates a processor core, memory (Flash, RAM), and peripherals (timers, UART, SPI, I2C, ADC) on one IC. In the hierarchy of embedded systems, an MCU is a type of integrated circuit, specifically a microcontroller, which falls under the broader category of semiconductors. The STM8L EnergyLite series is optimized for ultra-low-power operation, making it a key component in battery-powered and energy-harvesting designs. Key features include multiple low-power modes (Wait, Low-power Run, Low-power Wait, Active-halt, Halt) with current consumption as low as 0.3 µA in Halt mode, a 12-bit ADC, two comparators, a real-time clock (RTC), and a wide range of communication interfaces (USART, SPI, I2C). The device also includes an LCD driver (up to 8x40 segments), a 12-bit DAC, and a DMA controller, enhancing its versatility for sensor and display applications. The STM8L162M8T6 is built on a low-leakage CMOS process, achieving industry-leading energy efficiency. Its architecture supports fast wake-up times (as low as 4 µs) and dynamic voltage scaling, allowing designers to balance performance and power consumption. The integrated bootloader and in-application programming (IAP) capabilities simplify firmware updates in the field. Typical applications include portable medical devices (glucose meters, pulse oximeters), smart meters, wireless sensor nodes, and industrial process control. Its ultra-low-power modes and rich analog peripherals make it ideal for battery-powered systems where every microamp matters. When designing with this MCU, pay attention to the power supply decoupling: place a 100 nF capacitor close to each VDD pin and a 1 µF capacitor at the main supply. Use the low-power modes strategically to extend battery life, and ensure the crystal oscillator layout is clean to maintain accurate timing.

RFQ İletişim
STM8L162R8T6 - 16MHz 64KB Ultra-Low-Power MCU | STMicroelectronics
STM8L162R8T6

STM8L162R8T6 - 16MHz 64KB Ultra-Low-Power MCU | STMicroelectronics

The STMicroelectronics STM8L162R8T6 is an ultra-low-power 8-bit microcontroller with a 16 MHz clock, 64 KB of Flash memory, and a 64-pin LQFP package. It belongs to the high-density STM8L162x8 family and is designed for embedded systems that require compact control, low power consumption, and extensive peripheral integration. The manufacturer describes the enhanced STM8 CPU core as delivering up to 16 MIPS at 16 MHz. An ultra-low-power microcontroller is a semiconductor controller designed to minimize energy consumption during active operation and standby periods. The STM8L162 family sits within the broader hierarchy of microcontrollers, embedded processors, and semiconductor control devices. Its 8-bit architecture is suited to compact control tasks that collect sensor information, operate human-interface elements, manage communications, and sequence external hardware without requiring a high-end application processor. The STM8L162R8T6 combines a 16 MHz maximum clock with 64 KB of program Flash in an LQFP-64 package. The STM8L family designation identifies the device as an EnergyLite low-power MCU family, while the L162x8 group provides a larger pin count and greater peripheral integration than lower-density members. This combination is useful when a design needs more I/O than a small package can provide but does not require a 32-bit processor. Its 8-bit STM8 CPU core offers up to 16 MIPS at 16 MHz, giving designers deterministic performance for control-loop and firmware workloads. The 64 KB Flash capacity provides room for application code, boot logic, configuration data, and communication routines. Its 64-LQFP package also provides a generous pin count for external sensing, actuators, serial links, and discrete power-control functions, although the exact peripheral assignment must be confirmed against the pin-description table in the manufacturer documentation. Typical applications include low-power sensor nodes, industrial monitoring equipment, compact control panels, connected accessories, building and automation controllers, and battery-operated embedded products. In these systems, the MCU can manage local inputs, coordinate peripheral functions, and support serial data exchange while conserving energy during inactive intervals. The larger package is particularly useful where field wiring, status indicators, analog channels, or multiple communication interfaces are required. When designing around the STM8L162R8T6, begin with the manufacturer pin-description table and reference manual because no complete public pin assignment is reproduced on this page. Preserve the supply, ground, reset, and debug connections required by the device, and account for the thermal and electrical requirements of every connected peripheral. Firmware should also be tested across the intended voltage and temperature conditions before deployment. This product page combines the manufacturer's core device information, package and memory details, sourcing structure, drop-in alternatives, and practical engineering guidance. It is designed to help engineers identify the correct MCU, verify PCB compatibility, compare family alternatives, and plan power-aware embedded designs without requiring repetitive searches across technical documents.

RFQ İletişim
STM8S001J3M3 - 16MHz 8-bit MCU, 8KB Flash, SOIC-8 | STMicroelectronics
STM8S001J3M3

STM8S001J3M3 - 16MHz 8-bit MCU, 8KB Flash, SOIC-8 | STMicroelectronics

The STMicroelectronics STM8S001J3M3 is a 16 MHz 8-bit STM8S microcontroller with 8 KB of Flash program memory, 128 bytes of true data EEPROM, and a 10-bit ADC, packaged in an 8-pin SOIC (SO-8/SO8N) outline. It is the lowest-pin-count member of the mainstream STM8S value line, offering the full STM8S peripheral set in a footprint as small as the ATtiny13/ATtiny85. According to the ST datasheet (DocID026881), the device integrates a Harvard-architecture 3-stage pipeline core, three timers, plus UART, SPI, and I2C communication interfaces, all in a tiny 8-pin package. A microcontroller (MCU) is an integrated circuit that combines a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), small non-volatile data storage (EEPROM), and a configurable set of digital and analog peripherals on a single silicon die. The STM8S family sits in the 8-bit MCU category, which traces up the hierarchy to microcontroller -> embedded processor -> semiconductor IC. The STM8S core uses an extended instruction set that is binary-compatible across the STM8S/STM8L families, making code portable to higher-pin-count siblings when the design grows. Key features include 8 KB Flash with in-application/in-circuit programming, 128 bytes of true byte-erasable EEPROM rated for 100 k cycles, 1 KB SRAM, 5 ADC channels with 10-bit resolution and up to 12-bit oversampling, a 16 MHz internal RC oscillator calibrated to ±1%, and a 1.8 V to 5.5 V supply range. The 8-pin SOIC exposes just enough I/O to drive a handful of switches, LEDs, sensors, or a serial link, and the integrated brown-out reset and watchdog timer simplify safety-critical designs. Two 16-bit timers and one 8-bit timer provide PWM, input capture, and output compare functions for motor, LED, and timing control. Architecturally, the STM8S001J3 is a derivative of the STM8S003F3 with the same silicon die repackaged into an 8-pin SOIC, dropping most GPIOs in favor of a tiny PCB footprint. The integrated voltage regulator lets the chip run from a single 1.8-5.5 V rail without external components. With an active-mode current in the single-digit mA range and multiple low-power modes down to a few microamps, it is well suited to battery-powered gadgets and always-on sensor nodes. Typical applications include low-cost sensor interface boards, replacement of ATtiny13/ATtiny85 designs, smart LED controllers, IR remote transmitters/receivers, simple motor and fan controllers, battery chargers, and hobby/educational platforms such as the STM8 eForth project. The wide operating temperature range (-40C to +125C) and 5 V tolerance on most pins also make it viable for industrial control front-ends. When designing with this device, note that only 6 of the 8 pins are usable as GPIO because NRST and power pins are mandatory. Use the SWIM debug interface for in-circuit programming and debugging, and place a 100 nF decoupling capacitor as close as possible to the VDD pin. Compare pinout carefully against ATtiny85 migration paths before re-using existing PCB layouts. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the ST datasheet, helping engineers quickly evaluate the STM8S001J3M3 for low-pin-count 8-bit designs.

RFQ İletişim
STM8S003F3P6 - 8-bit MCU 8KB Flash 16MHz TSSOP-20 | STMicroelectronics
STM8S003F3P6

STM8S003F3P6 - 8-bit MCU 8KB Flash 16MHz TSSOP-20 | STMicroelectronics

The STMicroelectronics STM8S003F3P6 is a value line 8-bit microcontroller based on the STM8 core, running at up to 16 MHz with 8 KB of Flash memory, 1 KB of RAM, and 128 bytes of true data EEPROM in a 20-pin TSSOP package. An 8-bit microcontroller (MCU) is a single-chip computer integrating an 8-bit CPU, program memory, data memory, and programmable peripherals. The STM8S003F3P6 belongs to the STM8S series within the STM8 family, positioned below the 32-bit STM32 series in STMicroelectronics' product hierarchy and targeting cost-sensitive embedded control. Key features include 8 KB Flash with integrated true EEPROM (up to 100,000 write/erase cycles), a 10-bit ADC with 5 channels, and UART, SPI, and I2C interfaces. The device operates from 2.95V to 5.5V, supporting both 3.3V and 5V systems, with 16 programmable I/Os and 7 timers/counters including a 16-bit timer, an 8-bit timer, and watchdog timers. The STM8 core uses a Harvard-architecture 3-stage pipeline delivering 16 MIPS at 16 MHz. An internal 16 MHz RC oscillator eliminates the need for an external crystal in many designs. Low-power modes include Halt, Active-Halt, and Wait, with 3.6 mA typical in Run mode at 16 MHz and about 1 uA in Halt mode. Typical applications include home appliances, industrial control, consumer electronics, motor control helpers, and sensor interfaces. Its wide voltage range and robust I/O make it popular in white goods, power tools, and battery-powered devices, while the integrated EEPROM removes external non-volatile memory from the BOM. Design tip: decouple VDD with a 100 nF capacitor placed close to the pin. The internal RC is accurate to approximately 2%, so use an external crystal when precise timing is required. SWIM single-wire in-circuit programming simplifies firmware updates. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes beyond the ST datasheet, as of 2026-08-29.

USD $0,36 İletişim
STM8S003F3P6TR - 8-bit MCU, 8KB Flash, 16MHz | STMicroelectronics
STM8S003F3P6TR

STM8S003F3P6TR - 8-bit MCU, 8KB Flash, 16MHz | STMicroelectronics

The STMicroelectronics STM8S003F3P6TR is an 8-bit microcontroller based on the STM8 core, offering 8KB of Flash memory, 1KB of RAM, and 640 bytes of EEPROM in a 20-pin TSSOP package. It operates at a maximum frequency of 16 MHz and supports a supply voltage range of 2.95V to 5.5V, making it suitable for a wide range of cost-sensitive embedded applications. Data verified as of 2026-08-05. An 8-bit microcontroller (MCU) is a compact integrated circuit that contains a processor core, memory, and programmable input/output peripherals on a single chip. The STM8 core is an 8-bit CISC architecture designed for high code density and efficient performance in low-cost applications. As a member of the STM8S series, this MCU sits within the broader hierarchy of microcontrollers, which are themselves a subset of embedded processors used in everything from consumer electronics to industrial control systems. Key features include 8KB of Flash program memory, 1KB of SRAM, and 640 bytes of true data EEPROM with write protection. The device integrates a 10-bit analog-to-digital converter (ADC) with up to 5 channels, a UART, SPI, and I2C interface, and a 16-bit timer with PWM capability. It also includes a watchdog timer, a clock security system, and a low-power mode to minimize energy consumption. The STM8S003F3P6TR is built on a robust 8-bit architecture with a 3-stage pipeline, enabling most instructions to execute in a single clock cycle. The device supports a wide operating temperature range from -40°C to +85°C, making it reliable for industrial environments. The TSSOP-20 package offers a compact footprint of 6.4mm x 4.4mm, ideal for space-constrained PCB designs. Typical applications include home appliances, small appliances, lighting control, power tools, and sensor interfaces. Its rich peripheral set and low cost make it a popular choice for high-volume consumer products where cost efficiency is paramount. When designing with this MCU, ensure proper decoupling of the VDD pin with a 100nF capacitor placed close to the device. The NRST pin should be connected to VDD through a 100nF capacitor and a pull-up resistor to prevent spurious resets. For programming, the SWIM interface requires a single-wire connection, simplifying in-circuit programming. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the ST datasheet, providing engineers with a comprehensive resource for evaluating the STM8S003F3P6TR.

RFQ İletişim
STM8S003K3T6 - 8-bit 16MHz MCU, 8KB Flash | STMicroelectronics
STM8S003K3T6

STM8S003K3T6 - 8-bit 16MHz MCU, 8KB Flash | STMicroelectronics

The STMicroelectronics STM8S003K3T6 is an 8-bit value-line STM8S microcontroller featuring a 16 MHz advanced STM8 core, 8 KB of Flash program memory and 128 bytes of true data EEPROM, housed in a 32-pin LQFP (7x7 mm) package. According to the manufacturer datasheet, the device integrates a 10-bit ADC, three general-purpose 16-bit timers, a UART, SPI and I2C communication interfaces, plus independent watchdog timers with separate clock source for safety-critical applications. The chip operates from 2.95 V to 5.5 V supply and is built on ST's state-of-the-art 130 nm embedded Flash process. A value-line microcontroller (often called an 8-bit MCU) is a small, low-cost processor optimised for embedded control tasks such as sensor reading, motor actuation, indicator driving, and user-interface handling. Within the broader semiconductor hierarchy, an MCU is a subset of microprocessors (MPU) and is differentiated by integrated Flash, RAM and peripherals on a single die. The STM8S003K3T6 occupies the entry-level value-line of the STM8S family, balancing die size, peripheral set and price for cost-sensitive designs where a 32-bit MCU is unnecessary. Key features that differentiate the STM8S003K3T6 in its class include 1 KB of RAM, the integrated 10-bit SAR ADC with up to 5 multiplexed channels, the clock security system (CSS) that detects external clock failure and switches to the internal RC oscillator, plus 100 k write/erase cycle endurance on the data EEPROM. Robust I/O design tolerates 5 V injection on adjacent pins, simplifying mixed-voltage interface to legacy 5 V peripherals. The 32-pin LQFP-32 (7x7) footprint provides easy hand-soldering and breadboard prototyping versus fine-pitch QFN options. Technically, the STM8S003K3T6 is engineered around the proprietary STM8 core with 16-bit index registers and a 20-bit program counter, executing most instructions in 1-2 clock cycles. The integrated voltage regulator and brown-out reset (BOR) circuitry protect the Flash against low-voltage write corruption. The 16 MHz system clock can be sourced from an external crystal, resonator, or the factory-trimmed internal 16 MHz RC oscillator with ±1 % accuracy across the full operating temperature range. Typical applications include low-cost consumer appliances (rice cookers, washing-machine user interfaces, induction cooktops), battery-powered sensor nodes, LED lighting controllers, simple BLDC/PMSM auxiliary motor drivers (fans, pumps), 5 V industrial control buttons, and Arduino-Nano-compatible hobbyist boards. The wide 2.95-5.5 V supply range and proven STM8 toolchain (STVD, IAR, Cosmic, SDCC) make it a frequent second source for legacy 8051 designs requiring a software refresh. When designing with the STM8S003K3T6, choose between the internal 16 MHz RC oscillator (saves BOM cost) and an external crystal (better UART baud-rate accuracy). Decouple VDD/VSS with 100 nF ceramic capacitors placed within 3 mm of each supply pin, and reserve the SWIM pin (single-wire debug) for in-circuit programming. For noisy environments, enable the CSS and the window watchdog for IEC 60730 class B compliance. This page synthesizes distributor pricing, drop-in alternatives and practical design notes not found in the manufacturer datasheet, and is intended as a faster reference than the 31-page ST datasheet for engineers evaluating the part for production.

RFQ İletişim
STM8S003K3T6C - 16MHz 8-bit MCU | STMicroelectronics
STM8S003K3T6C

STM8S003K3T6C - 16MHz 8-bit MCU | STMicroelectronics

STMicroelectronics STM8S003K3T6C is a value-line 8-bit STM8S microcontroller with a 16 MHz clock, 8 KB of Flash program memory, 128 bytes of true data EEPROM, and a 10-bit ADC, all housed in a 32-LQFP package measuring 7 x 7 mm. The device also provides UART, SPI, and I2C serial interfaces for compact embedded-control designs. A microcontroller is a programmable semiconductor that integrates a CPU core, nonvolatile program memory, data memory, peripherals, and input/output ports on one package. Within the product hierarchy, the STM8S003K3T6C is an 8-bit MCU, a low-density member of the STM8S microcontroller family, and a value-line device intended for cost-sensitive embedded systems. Its 16 MHz operating clock supports responsive control tasks without requiring a more complex processor architecture. Key features include 8 KB of Flash memory, 128 bytes of true data EEPROM, and a 10-bit analog-to-digital converter. Three timers support timing, counting, and basic motor or control tasks. The integrated UART, SPI, and I2C interfaces allow the MCU to connect sensors, displays, transceivers, and other digital peripherals while limiting external component count. Its 16 I/O ports provide dedicated mixed-signal and communication access on the 32-LQFP package. The STM8S003F3/K3 value-line architecture is positioned between simple logic controllers and larger 8-bit microcontrollers. True EEPROM preserves frequently changed configuration or calibration values without requiring an external memory component. The ADC supports analog measurement, while the serial peripherals cover asynchronous communication, sensor buses, and displays. Designers should still verify the exact peripheral mapping and alternate-function assignments for their selected pins in the manufacturer pin-description table. Typical applications include compact sensor nodes, appliance controllers, small motor-control boards, digital timers, LED-control systems, simple battery-powered instruments, and industrial monitoring modules. The combination of Flash, EEPROM, ADC, and three serial interfaces is particularly useful when a board must combine local control with a few external sensors or communication devices while minimizing board area and firmware overhead. A key design consideration is package verification. The STM8S003K3T6C uses a 32-LQFP footprint, so replacement parts must match its pin arrangement, power pins, oscillator connections, and exposed analog functions. Check startup, reset, and debug requirements in the manufacturer reference manual, and confirm that the selected supply voltage and external component values satisfy the electrical limits for the operating temperature range. This page combines manufacturer specifications, package and lifecycle information, interface-oriented application guidance, and a strict drop-in replacement review. It also distinguishes electrical and mechanical compatibility from simple functional similarity, helping engineers shortlist a device for an existing STM8S003K3T6C PCB with greater engineering confidence.

RFQ İletişim
STM8S005C6T6 - 8-bit MCU, 32KB Flash, 16MHz | STMicroelectronics
STM8S005C6T6

STM8S005C6T6 - 8-bit MCU, 32KB Flash, 16MHz | STMicroelectronics

The STM8S005C6T6 is an 8-bit microcontroller from STMicroelectronics' STM8S value line, featuring a 16 MHz STM8 core, 32 Kbytes of Flash program memory, and 128 bytes of data EEPROM. It is housed in a 48-pin LQFP (7x7 mm) package, offering a compact footprint for space-constrained embedded applications. An 8-bit microcontroller (MCU) is a single-chip computer with an 8-bit data bus, integrating a processor core, memory, and programmable peripherals. The STM8S005C6T6 belongs to the STM8S family, which is part of the broader STM8 8-bit MCU category, positioned below 32-bit ARM Cortex-M devices in the microcontroller hierarchy. It provides a cost-effective solution for applications requiring moderate processing power and rich peripheral integration without the complexity of 32-bit architectures. Key features include a 16 MHz CPU clock, 32 KB Flash, 2 KB RAM, 128 bytes EEPROM, and a comprehensive set of peripherals: 10-bit ADC, UART, SPI, I2C, timers, and up to 38 I/O pins. The device operates from a 2.95V to 5.5V supply, making it suitable for both 3.3V and 5V systems. Its robust ESD protection and wide operating temperature range (-40°C to +85°C) enhance reliability in industrial environments. The STM8S005C6T6 is built on ST's proprietary STM8 core, which delivers up to 20 MIPS at 16 MHz, providing efficient code execution for control-oriented tasks. The integrated EEPROM allows data storage without external components, simplifying BOM and reducing system cost. The device supports in-circuit programming and debugging via SWIM interface, enabling rapid firmware development. Typical applications include home appliances, industrial control, sensor interfaces, and consumer electronics. Its 5V-tolerant I/Os and rich peripheral set make it ideal for motor control, lighting, and power management systems. The wide voltage range and low power consumption support battery-powered devices. When designing with this MCU, ensure proper decoupling of the VDD pins with 100nF capacitors and a bulk capacitor. The SWIM pin should be pulled high for programming. For EMC-sensitive designs, follow ST's layout guidelines for the LQFP package to minimize noise coupling.

RFQ İletişim
STM8S005C6T6TR - 8-bit MCU, 32KB Flash, 16MHz | STMicroelectronics (Tape & Reel)
STM8S005C6T6TR

STM8S005C6T6TR - 8-bit MCU, 32KB Flash, 16MHz | STMicroelectronics (Tape & Reel)

The STM8S005C6T6TR is an 8-bit microcontroller from STMicroelectronics' STM8S value line, featuring a 16 MHz STM8 core, 32 Kbytes of Flash program memory, and 128 bytes of data EEPROM. It is housed in a 48-pin LQFP (7x7 mm) package, offering a compact footprint for space-constrained embedded applications. An 8-bit microcontroller (MCU) is a single-chip computer with an 8-bit data bus, integrating a processor core, memory, and programmable peripherals. The STM8S005C6T6TR belongs to the STM8S family, which is part of the broader STM8 8-bit MCU category, positioned below 32-bit ARM Cortex-M devices in the microcontroller hierarchy. It provides a cost-effective solution for applications requiring moderate processing power and rich peripheral integration without the complexity of 32-bit architectures. Key features include a 16 MHz CPU clock, 32 KB Flash, 2 KB RAM, 128 bytes EEPROM, and a comprehensive set of peripherals: 10-bit ADC, UART, SPI, I2C, timers, and up to 38 I/O pins. The device operates from a 2.95V to 5.5V supply, making it suitable for both 3.3V and 5V systems. Its robust ESD protection and wide operating temperature range (-40°C to +85°C) enhance reliability in industrial environments. The STM8S005C6T6TR is built on ST's proprietary STM8 core, which delivers up to 20 MIPS at 16 MHz, providing efficient code execution for control-oriented tasks. The integrated EEPROM allows data storage without external components, simplifying BOM and reducing system cost. The device supports in-circuit programming and debugging via SWIM interface, enabling rapid firmware development. Typical applications include home appliances, industrial control, sensor interfaces, and consumer electronics. Its 5V-tolerant I/Os and rich peripheral set make it ideal for motor control, lighting, and power management systems. The wide voltage range and low power consumption support battery-powered devices. When designing with this MCU, ensure proper decoupling of the VDD pins with 100nF capacitors and a bulk capacitor. The SWIM pin should be pulled high for programming. For EMC-sensitive designs, follow ST's layout guidelines for the LQFP package to minimize noise coupling.

RFQ İletişim
STM8S005K6T6C - 16MHz 8-Bit MCU, 32KB Flash, LQFP-32 | STMicroelectronics
STM8S005K6T6C

STM8S005K6T6C - 16MHz 8-Bit MCU, 32KB Flash, LQFP-32 | STMicroelectronics

The STMicroelectronics STM8S005K6T6C is a value-line 8-bit microcontroller (MCU) with a 16 MHz core, 32 KB of Flash program memory, 2 KB of RAM and 128 bytes of data EEPROM, packaged in a 32-pin LQFP (7x7 mm). It is the 32-pin member of the STM8S005C6/K6 family and is intended for cost-sensitive, high-volume embedded control designs. What is an 8-bit value-line microcontroller? An MCU is a complete single-chip computer: a CPU core, program Flash, data RAM, embedded EEPROM, and on-chip peripherals on one die. The "value line" designation means ST optimized the STM8S005 for low cost and low power rather than for maximum performance or peripheral count. In the hierarchy it sits as: 8-bit MCU -> embedded microcontroller -> general-purpose IC -> semiconductor. The 8-bit core naturally handles small state machines, sensor conditioning, key scanning, and actuator control where 16- or 32-bit processing is unnecessary. Key features include a maximum 16 MHz core clock, 32 KB Flash, 2 KB SRAM, 128 bytes of EEPROM, a 10-bit successive-approximation ADC, and the ST 8-bit peripheral set: one UART, one SPI interface, one I2C interface, 16-bit timers with PWM channels, and an internal 8 MHz RC oscillator with external clock support. All timers can be clocked from the internal RC source, allowing cost savings on the crystal/ceramic resonator. Architecturally the STM8S005 core uses a single-cycle Harvard architecture with an 8-bit data bus, so Flash is accessed in a single cycle and the pipeline executes most instructions in one to three cycles. This gives real-world performance well above what the 16 MHz headline number suggests for typical control code. On-chip debug and programming are handled through the standard ST 8-bit debug interface (SWIM plus optional SWD on related devices), and the toolchain is the free ST-LINK / STM8CubeProgrammer ecosystem. Typical applications include small home appliances, kitchen and white-goods control boards, simple sensor-hub nodes, LED and lighting controllers, toys, security keypads, and low-cost industrial control modules where a small pin count and low unit cost matter more than processing headroom. One design consideration dominates: this is a 32-pin LQFP, so GPIO and peripheral breakout is modest. Plan pin multiplexing for I2C, SPI, and UART carefully before finalizing the PCB, and confirm the ADC reference and operating supply range in the manufacturer datasheet before committing to a power rail. This page consolidates manufacturer specifications, package and pinout detail, drop-in replacement options, and practical design notes so you can qualify the STM8S005K6T6C for a new design or a board repair without piecing together information from multiple sources.

RFQ İletişim
STM8S007C8T6 - 8-Bit MCU, 64KB Flash, 24MHz | STMicroelectronics
STM8S007C8T6

STM8S007C8T6 - 8-Bit MCU, 64KB Flash, 24MHz | STMicroelectronics

The STM8S007C8T6 is an 8-bit microcontroller from STMicroelectronics' STM8S Value Line family, featuring a 24MHz advanced STM8 core with Harvard architecture and a 3-stage pipeline. It comes in a 48-pin LQFP package and offers 64KB of Flash memory, 6KB of RAM, and true data EEPROM. With 38 programmable I/O lines, 9 timers/counters, and interfaces including I2C, SPI, and 2 UARTs, this MCU is designed for cost-sensitive embedded applications requiring robust performance and low power consumption. An 8-bit microcontroller is a single-chip computer with an 8-bit central processing unit (CPU), memory, and programmable input/output peripherals. It is a type of embedded microcontroller, which is a compact integrated circuit designed to govern a specific operation in an embedded system. The STM8S007C8T6 belongs to the STM8 family, which is a line of 8-bit microcontrollers from STMicroelectronics, positioned between low-end 8-bit MCUs and higher-performance 32-bit ARM Cortex-M devices. Its Harvard architecture separates instruction and data buses, enabling simultaneous access and faster execution, while the 3-stage pipeline increases throughput at a given clock frequency. Key features of the STM8S007C8T6 include a maximum CPU frequency of 24MHz with 0 wait states at 16MHz, 64KB of Flash memory, 6KB of RAM, and true data EEPROM for non-volatile data storage. It integrates a 10-bit ADC, multiple timers, and communication interfaces (I2C, SPI, 2 UARTs), making it versatile for various control and monitoring tasks. The device operates over a temperature range of -40°C to 85°C and has a maximum power dissipation of 443mW, suitable for industrial and consumer environments. Technically, the STM8 core is an advanced 8-bit architecture with a 3-stage pipeline, allowing most instructions to execute in a single clock cycle. The 24MHz clock speed provides up to 24 MIPS throughput, which is competitive for 8-bit MCUs. The Flash memory supports in-application programming (IAP) and in-circuit programming (ICP), enabling firmware updates in the field. The true data EEPROM allows for byte-level read/write operations, useful for storing calibration data or system parameters without external memory. Typical applications include home appliances, industrial control, sensor interfacing, and automotive body electronics. The rich peripheral set and 38 I/O lines make it suitable for motor control, lighting systems, and human-machine interfaces. Its low power consumption and wide operating voltage range (typically 2.95V to 5.5V) support battery-powered devices and 5V logic systems. When designing with this MCU, consider the power supply decoupling and crystal oscillator layout. Use a 0.1uF capacitor close to each VDD pin and a 10uF bulk capacitor. For the external crystal, place it near the OSC pins with proper load capacitors as specified in the datasheet. Ensure the reset pin has a pull-up resistor and a capacitor for reliable power-on reset.

RFQ İletişim