Ürünler (44.000+)

TJA1040T/CM - 1 MBaud CAN Transceiver | NXP
TJA1040T/CM

TJA1040T/CM - 1 MBaud CAN Transceiver | NXP

The NXP Semiconductors TJA1040T/CM is a high-speed CAN transceiver rated for operation up to 1 MBaud and supplied in an 8-pin SO package. It provides differential transmit capability to the physical CAN bus and differential receive capability to a CAN protocol controller, making it an interface between controller-area-network logic and vehicle or industrial bus wiring. A CAN transceiver is a physical-layer interface IC within the broader interface-IC hierarchy. It converts the controller’s digital logic signals into differential bus signaling and converts differential bus levels back into logic-compatible receive signals. The TJA1040 is intended primarily for high-speed passenger-car CAN networks, where robust differential signaling, standby control, and electromagnetic compatibility are important. The verified manufacturer information identifies differential transmission, differential reception, high-speed operation up to 1 MBaud, and standby-mode capability as principal device features. The distributor record identifies the TJA1040T/CM,118 ordering form as an 8-pin SO CAN-bus transceiver. Detailed electrical limits, loop-delay values, bus-fault behavior, and package dimensions were not supplied in the verified extract and therefore require confirmation from the manufacturer datasheet before design release. Typical uses include passenger-vehicle body and powertrain CAN networks, automotive control modules, CAN gateways, and industrial equipment that uses a 5 V CAN physical layer. The transceiver is intended to operate with a compatible CAN controller rather than as a standalone bus controller. Its differential bus interface supports robust communication over cable networks, while the standby function can reduce activity when the node is not communicating. Designers should preserve the pin assignment, supply decoupling, CANH/CANL routing, termination, and common-mode protection described by the manufacturer. The verified source set does not include the complete pinout, absolute maximum ratings, thermal data, or EMC test values, so those details must not be inferred. This page combines official NXP information with distributor records and explicitly marks unavailable parameters rather than estimating them. TJA1040T/CM is a legacy EoL-positioned part according to the supplied migration context. For new designs, engineers should compare it with current NXP or third-party CAN transceivers and verify pin, electrical, lifecycle, and qualification compatibility before treating any replacement as drop-in.

RFQ İletişim
TJA1040T/N1 - 1 Mbit/s CAN Transceiver | NXP Semiconductors
TJA1040T/N1

TJA1040T/N1 - 1 Mbit/s CAN Transceiver | NXP Semiconductors

The NXP Semiconductors TJA1040T/N1 is a high-speed CAN bus transceiver with a maximum signaling rate of 1 Mbit/s, supplied in an 8-pin SO package. It provides the physical-layer interface between a CAN protocol controller and the differential CAN bus, combining a differential transmitter with a differential receiver. The device is intended primarily for high-speed in-vehicle passenger-car networks, where a compact controller-to-bus interface enables distributed automotive electronics to exchange safety, body, and powertrain-related data. A CAN transceiver is a semiconductor interface device that converts logic-level transmit and receive signals into the differential signaling used on a Controller Area Network. In the hierarchy of electronic components, the TJA1040T/N1 is an interface IC, specifically a CAN physical-layer transceiver. A host microcontroller or dedicated CAN controller handles message framing, arbitration, filtering, and protocol timing, while the transceiver translates those controller signals into robust bus-level voltages and converts received bus states into logic-compatible data. The key operating headline is a maximum data rate of 1 Mbit/s, with differential transmit and receive capability. The 8-SO package keeps the physical interface compact for automotive electronic control units and other embedded CAN systems. The NXP product page specifically identifies passenger cars as the principal application environment. These characteristics make the TJA1040T/N1 relevant to designs that need a conventional high-speed CAN physical layer rather than a low-speed fault-tolerant body-network interface. The TJA1040T/N1 belongs to an older generation of CAN transceivers whose successor products can add functions such as standby control, split-buffer operation, or expanded I/O voltage support. Its core role remains straightforward: TXD accepts a controller-side transmit signal, RXD presents the received bus state to the controller, and the differential CANH and CANL pins connect to the bus. Exact electrical limits, loopback behavior, and pin functions should be checked against the manufacturer data sheet before final circuit release. Typical applications include passenger-car body-control modules, powertrain controllers, automotive comfort systems, CAN-based sensors, and industrial or embedded equipment using a standard 1 Mbit/s CAN network. In an automotive control unit, the transceiver provides the physical link between a CAN controller and the two-wire bus while leaving protocol functions to the controller. Its differential interface also suits systems where minimizing susceptibility to common-mode noise is important. PCB design should preserve the short, symmetric CANH and CANL connection between the transceiver and the bus connector, keep the connector and bus stubs short, and provide the required decoupling directly at the device supply pins. The 8-SO footprint simplifies assembly but requires careful escape routing around the two bus pins. Review the recommended application circuit, termination requirements, supply voltage, and loopback configuration in the NXP data sheet when laying out the module. This product record combines the manufacturer interface description, ordering information, package details, lifecycle information, and replacement guidance with practical PCB considerations. It also distinguishes strict same-footprint substitutes from newer CAN transceivers that offer additional functions but may require different pin interpretation or board-level qualification.

RFQ İletişim
TJA1040T/VM - 1Mbit CAN Transceiver | NXP | Automotive
TJA1040T/VM

TJA1040T/VM - 1Mbit CAN Transceiver | NXP | Automotive

The NXP TJA1040T/VM is a high-speed CAN physical-layer transceiver rated for data rates up to 1 Mbaud, operating from a 5 V supply, and packaged in an 8-pin SO small-outline package. It provides the differential transmitter and receiver interface between a CAN protocol controller and the physical CAN bus, making it suitable for passenger-car and other high-speed Controller Area Network systems. A CAN transceiver is an interface IC within the broader hierarchy of CAN interface devices, bus transceivers, wired-network interfaces, and semiconductors. It translates logic-level TXD and RXD signals into the differential CANH and CANL bus conductors and converts received bus differential voltage back into a logic-compatible RXD signal. This physical-layer function separates CAN protocol processing in a controller from the electrical drive, receive, and bus-failure behavior implemented by the transceiver. The TJA1040 supports high-speed CAN operation up to 1 Mbaud, making it appropriate for engine, chassis, body, and other automotive networks operating within that bandwidth. Its 5 V supply arrangement matches conventional automotive CAN interface environments. The device also provides power-down and standby operating states, allowing a system to reduce activity when communication is not required. The listed 8-SO package supports compact surface-mount PCB layouts. The transceiver architecture combines a differential CAN output stage with a differential input receiver. TXD is the controller-facing transmit input, while RXD is the controller-facing receive output. CANH and CANL provide the physical connection to the bus, VCC supplies the transceiver, VIO supports the interface voltage domain, and EN provides operating-state control. These functions allow a CAN controller to communicate through a multi-conductor differential bus while keeping protocol handling separate from bus signaling. Typical applications include passenger-car CAN networks, automotive body and chassis control modules, powertrain control equipment, industrial CAN equipment operating at compatible bus speeds, and embedded CAN gateways. In each application, the controller generates TXD and receives RXD, while the TJA1040 handles the physical bus interface. Board design must preserve the transceiver's supply, reference-ground, input, and bus-connection requirements to maintain signal integrity. When laying out the PCB, place the transceiver and its local decoupling capacitor close to the associated CAN controller, keep CANH and CANL routing compact and symmetrical, and provide the bus termination and common-mode network required by the selected CAN topology. Differential routing reduces sensitivity to external noise, while correct termination prevents excessive reflections from degrading communication at the maximum supported data rate. This product page combines the NXP device description with package, interface, application, comparison, and layout guidance. It also distinguishes verified source facts from engineering choices that depend on bus topology, termination strategy, controller supply voltage, and EMC validation.

RFQ İletişim
TJA1041AT - 1 Mbit/s High-Speed CAN Transceiver | NXP
TJA1041AT

TJA1041AT - 1 Mbit/s High-Speed CAN Transceiver | NXP

NXP Semiconductors TJA1041AT is a high-speed CAN transceiver intended for automotive Controller Area Network nodes operating at data rates up to 1 Mbit/s. It provides differential transmit capability to the CAN bus and differential receive capability to the CAN protocol controller, with a 4.75 V to 5.25 V supply range and a 14-pin SOIC surface-mount package. The device is designed for use with a 5 V CAN controller interface. A CAN transceiver is the physical-layer interface between a CAN protocol controller and a wired CAN bus. Within the hierarchy of CAN interface ICs, CAN transceivers sit between microcontrollers or dedicated CAN controllers and the differential bus. They combine a transmitter, receiver, bus-driver protection, and logic-level interfaces into one component. This integration allows a protocol controller to exchange messages with other CAN nodes while the transceiver handles the physical signaling characteristics of the bus. The TJA1041AT supports CAN data rates up to 1 Mbit/s and is compatible with the ISO 11898 standard. Its differential transmitter and receiver support communication over a balanced CAN bus, while its digital transmit and receive pins connect to a CAN controller. NXP identifies the TJA1041AT as an end-of-life product, so long-lived automotive, industrial, and transportation programs should confirm lifecycle strategy and replacement planning with NXP before committing new production volumes. The SOIC-14 package provides separate connections for logic supply, transceiver supply, transmit data, receive data, standby control, CANH, and CANL. Its surface-mount construction supports automated PCB assembly, while the comparatively large lead pitch facilitates inspection and rework compared with fine-pitch packages. Precise pin names, truth-table behavior, electrical limits, and unused-pin connections should be assigned directly from the pin-description table and application information in the manufacturer datasheet. Typical uses include automotive body and powertrain networking, industrial automation equipment, transportation controllers, embedded CAN gateways, and diagnostic interfaces. The 1 Mbit/s capability suits conventional high-speed CAN networks used throughout vehicle and factory automation systems. A suitable host controller must support the device's logic levels, supply arrangement, standby behavior, and CAN protocol requirements. Designers should preserve the recommended transceiver and controller grounding arrangement, route CANH and CANL as a differential pair, and place protection or termination components where the bus topology requires them. Bus termination, common-mode range, loop delay, radiated emissions, and fault tolerance must be evaluated at system level rather than inferred solely from the nominal data rate. This product page combines the manufacturer lifecycle status, datasheet characteristics, application guidance, and cross-reference assessment to support engineering selection. It also distinguishes a genuine PCB-footprint replacement from merely similar CAN devices, avoiding the unsafe assumption that equal functionality automatically means pin-to-pin compatibility.

RFQ İletişim
TJA1041AT/N - 1 Mbit/s High-Speed CAN Transceiver | NXP
TJA1041AT/N

TJA1041AT/N - 1 Mbit/s High-Speed CAN Transceiver | NXP

The NXP Semiconductors TJA1041AT/N is a high-speed CAN bus transceiver for automotive applications operating at data rates up to 1 Mbit/s. It provides a physical-layer interface between a CAN protocol controller and the differential CAN bus, offering differential transmit and receive functions in a 14-pin SO package. Its nominal 5 V supply range is 4.75 V to 5.25 V. A CAN transceiver, also called a CAN physical-layer interface, converts logic-level signals from a CAN controller into differential bus signals and converts the received bus state back into a logic signal. Within the automotive electronics hierarchy, the TJA1041AT/N belongs to the CAN interface IC class, connecting the protocol-control layer to the physical communication bus. The principal feature of the TJA1041AT/N is its support for high-speed CAN communication up to 1 Mbit/s. Differential CAN signaling improves immunity to electromagnetic noise, while the transceiver's transmit and receive paths integrate the controller and bus into one physical-layer solution. The device is specifically intended for automotive high-speed CAN nodes, where robust differential signaling, compact packaging, and predictable interoperability are important. The TJA1041A family uses a nominal 5 V operating environment, with the documented supply range of 4.75 V to 5.25 V. The 14-pin SO package supports surface-mount PCB assembly and provides the CANH and CANL bus connections together with controller-facing TXD, RXD, and error-status signaling. Exact pin functions, absolute maximum ratings, loop-delay limits, and output-stage characteristics should be taken from the manufacturer datasheet. Typical deployments include automotive body and comfort modules, powertrain controllers, gateway units, cluster electronics, infotainment systems, and industrial CAN equipment that implements a compatible high-speed CAN physical layer. In these systems, the transceiver replaces discrete driver and receiver circuitry around the CAN controller while keeping the PCB layout compact. When laying out the circuit, place the transceiver close to the bus connector and route CANH and CANL as a matched differential pair. Keep the connection from CANH and CANL through the connector as short as practical, follow the datasheet recommendations for termination, and use the pin-description table in the manufacturer datasheet when assigning PCB tracks. The NXP product page identifies TJA1041AT as end of life, so new designs should confirm the recommended successor before committing the footprint. This page combines the manufacturer's product information, datasheet links, distributor records, lifecycle information, and packaging details with practical application guidance, comparison parameters, and board-level design notes. It is intended to accelerate component selection and design-in work while keeping the final engineering decisions anchored to the official NXP documentation.

RFQ İletişim
TJA1041AT/V - 1Mbit/s High-Speed CAN Transceiver | NXP
TJA1041AT/V

TJA1041AT/V - 1Mbit/s High-Speed CAN Transceiver | NXP

The NXP Semiconductors TJA1041AT/V is a high-speed CAN transceiver designed for automotive Controller Area Network nodes operating at data rates up to 1 Mbit/s. It provides differential transmit and receive capabilities between a CAN protocol controller and the physical CAN bus, operates from a 4.75 V to 5.25 V supply, and is offered in a 14-pin SO package. The device is intended for automotive electronic control units, body modules, instrumentation systems, and other embedded networking equipment that require a robust interface between a digital CAN controller and a differential bus. A CAN transceiver is an interface IC within the broader Controller Area Network hierarchy. A CAN controller generates and interprets digital protocol frames, while the physical-layer transceiver converts controller signals into a differential CAN bus waveform and converts received bus levels back into logic-compatible receive data. The TJA1041AT/V therefore belongs to the CAN transceiver family, which operates at the physical-bus layer beneath communication controllers, embedded processors, and complete automotive electronic control units. Key operating features include support for high-speed CAN communication up to 1 Mbit/s, a 4.75 V minimum operating supply, a 5.25 V maximum operating supply, differential bus transmission, and differential bus reception. Its transceiver architecture allows a host controller to remain separate from the physical bus wiring while providing the electrical interface required for multi-node communication. The 14-pin SO package supports compact surface-mount assembly in automotive control-unit designs. The TJA1041A family is associated with ISO 11898 high-speed CAN communication and provides compatibility with CAN protocol controllers that provide TXD and RXD logic signals. The CANH and CANL connections carry complementary differential bus levels. This differential signaling improves common-mode noise rejection in vehicle electrical environments, where switching loads, alternator systems, and other transient-producing equipment can disturb the communication network. Typical applications include automotive body-control modules, powertrain controllers, gateway units, dashboard electronics, seat and door modules, lighting controllers, small electric motors, and industrial or transportation equipment using a CAN bus. In these systems, the transceiver is placed between the host CAN controller and the CANH and CANL network conductors. PCB routing, termination, grounding, and protection remain critical because the transceiver is only one element of the complete physical-layer network. Design the power and signal paths carefully around the 4.75 V to 5.25 V operating range. Decoupling should be placed close to the supply pins, the CANH and CANL traces should follow controlled-impedance routing practices, and the bus should use the termination strategy specified by the CAN network design. Protection components may be added when the cable environment includes severe automotive transients, provided their capacitance and clamping behavior do not distort the differential signal. This product page combines the NXP technical description with lifecycle information, package identification, practical interface guidance, sourcing questions, and clearly qualified replacement analysis. It also highlights where an existing design can be reused and where a new PCB and EMC validation are required before changing CAN transceivers.

RFQ İletişim
TJA1041T/H/V - 1Mbit/s High-Speed CAN Transceiver | NXP
TJA1041T/H/V

TJA1041T/H/V - 1Mbit/s High-Speed CAN Transceiver | NXP

The NXP Semiconductors TJA1041T/H/V is a high-speed CAN bus transceiver supporting data rates up to 1 Mbit/s, operating from a 5 V supply in a 14-pin SOIC package. It provides a differential CANH and CANL bus interface together with transmit and receive paths for connection between a CAN protocol controller and the physical CAN network. The device is designed for automotive high-speed CAN nodes and is compatible with the ISO 11898 standard. A CAN transceiver is an interface IC that translates logic-level signals from a CAN controller into differential physical-bus signals and converts received differential bus levels back into controller-compatible logic. In the hierarchy of electronic components, the TJA1041T/H/V is a CAN transceiver, which is a bus-interface device within the broader interface IC and semiconductor categories. Its primary role is to isolate the controller from the electrical characteristics, common-mode behavior, and fault conditions found on a wired CAN network. Key characteristics include operation at up to 1 Mbit/s, ISO 11898 compatibility, a nominal 5 V supply, and an operating temperature range of -40°C to +150°C. NXP describes the TJA1041 as providing excellent electromagnetic compatibility, very low power consumption, and passive behavior when the supply voltage is off. These characteristics make it relevant to automotive body, powertrain, chassis, and industrial CAN systems where bus reliability under temperature and electromagnetic stress is important. The transceiver uses differential signaling to improve common-mode rejection on the CAN bus. Its transmitter drives the CANH and CANL conductors, while its receiver interprets differential bus voltage. ISO 11898 compatibility provides a defined physical-layer framework for high-speed CAN communication. Because the TJA1041T/H/V does not include a CAN protocol controller, it must be paired with a controller containing CAN TX and RX logic rather than used as a standalone bus node. Typical applications include automotive electronic control units, body-control modules, powertrain controllers, industrial automation equipment, elevator controls, and embedded CAN gateways. The 1 Mbit/s capability suits conventional CAN systems, while the wide -40°C to +150°C operating range supports harsh industrial and automotive environments. Systems requiring a CAN controller with an integrated transceiver should use a different device family rather than adding this transceiver unnecessarily. Design attention should be directed to supply decoupling, termination, common-mode choke selection, protection against bus transients, and the separation of sensitive analog or communication paths from noisy power stages. A split termination network can improve EMC behavior, while a common-mode choke can reduce radiated emissions when appropriately selected. PCB placement should minimize loop area around the transceiver and bus-node components because long or poorly controlled high-current loops can increase emissions. This product reference combines lifecycle information, interface specifications, package details, application guidance, and same-package replacement considerations. It is intended to help engineers distinguish the original TJA1041T/H/V order code from related qualification and packing variants before making a PCB-compatible sourcing decision.

RFQ İletişim
TJA1041T/N1 - 1Mbit/s CAN Transceiver | NXP | SOIC-14
TJA1041T/N1

TJA1041T/N1 - 1Mbit/s CAN Transceiver | NXP | SOIC-14

The NXP TJA1041T/N1 is a high-speed CAN transceiver designed to connect a CAN protocol controller to a physical Controller Area Network bus. It supports data rates up to 1 Mbit/s, provides one CAN transmit and receive path, and is offered in a 14-pin SOIC surface-mount package for automotive high-speed CAN systems. A CAN transceiver is an interface IC within the automotive network-communication hierarchy. It translates the controller's logic-level TXD and RXD signals into a differential bus waveform for transmission and converts received differential bus levels into a logic signal for the controller. This physical-layer function complements the CAN protocol controller, which handles message identifiers, arbitration, error handling, and higher-level data exchange. The TJA1041T/N1 provides differential transmit capability, differential receive capability, and compatibility with high-speed CAN protocol controllers operating up to 1 Mbit/s. Its single-transceiver arrangement suits conventional CAN nodes that do not require the additional transceiver features found in sleep-capable variants. The SOIC-14 package supports surface-mount assembly while providing separate pins for the bus interface, logic interface, ground connection, and stabilization. Automotive and industrial CAN networks benefit from the robust differential signaling inherent in the TJA1041 architecture. Differential reception rejects common-mode voltage present on the bus, while the controller and transceiver can use twisted-pair wiring to maintain signal integrity over longer cable runs. The manufacturer's product documentation identifies the device primarily for automotive high-speed CAN applications and confirms compatibility with suitable CAN protocol controllers. Typical deployments include engine-control units, transmission controllers, body-control modules, gateways, electronic control units, industrial automation controllers, and CAN-based sensor or actuator networks. In these systems, the TJA1041T/N1 handles the physical bus layer while a separate CAN controller manages frame arbitration, acknowledgments, error counters, and communication with the host processor. Designers should follow the manufacturer's recommended transceiver and bus-line application circuit, including termination, common-mode choke or split-termination options where required, decoupling, and PCB routing guidance. The 1 Mbit/s capability does not remove the need for controlled bus topology, adequate ground references, correct termination placement, and protection suited to the vehicle or industrial environment. This page combines the TJA1041T/N1 lifecycle information, verified source links, same-footprint alternatives, application guidance, and engineering design notes to support component selection, PCB planning, and long-term supply-risk assessment.

RFQ İletişim
TJA1041T/VM - 1 Mbit/s CAN Transceiver | NXP Semiconductors
TJA1041T/VM

TJA1041T/VM - 1 Mbit/s CAN Transceiver | NXP Semiconductors

The NXP Semiconductors TJA1041T/VM is a high-speed Controller Area Network transceiver designed for automotive CAN nodes operating at speeds up to 1 Mbit/s. It provides differential transmit and receive functions between a CAN protocol controller and the physical CAN bus, and is offered in a 14-pin SOIC package. The TJA1041 family is listed as End of Life by NXP. A CAN transceiver is the physical-layer interface between a digital CAN controller and the differential bus wiring. It converts controller logic signals into a dominant or recessive differential bus state and converts bus levels into logic signals for the controller. This type of interface belongs to the hierarchy of CAN transceiver, communication interface IC, interface IC, and semiconductor. The TJA1041 supports CAN communication rates up to 1 Mbit/s and is primarily intended for high-speed automotive applications. Its differential receiver provides the interface from the bus to the controller, while its differential transmitter connects the node to the CAN network. The TJA1041T/VM package designation identifies the SOIC-14 variant with NXP's VM ordering suffix. Automotive electronics use CAN networks to connect engine-control, body, chassis, comfort, and diagnostic modules while reducing wiring complexity. A CAN node generally combines a protocol controller with a transceiver such as the TJA1041. The physical transceiver handles bus-level signaling, allowing the controller to exchange frames through a standardized communication interface. Typical uses include electronic control units, body-control modules, powertrain controllers, gateway electronics, automotive diagnostic interfaces, and industrial CAN equipment connected to 1 Mbit/s networks. Selection should consider bus speed, transceiver logic compatibility, termination strategy, package footprint, operating temperature, and the manufacturer's lifecycle status. PCB design must preserve the recommended CAN bus routing and termination arrangement, provide a stable transceiver supply, and maintain suitable common-mode behavior for the automotive network. Because the TJA1041T/VM is marked End of Life, new production designs should verify migration options and avoid depending on an unannounced second source. This product page combines the NXP functional description, package and lifecycle information, ordering references, and practical guidance for selecting, comparing, and implementing a replacement before an End of Life migration.

RFQ İletişim
TJA1042AT/0Z - 5Mbps High-Speed CAN Transceiver | NXP
TJA1042AT/0Z

TJA1042AT/0Z - 5Mbps High-Speed CAN Transceiver | NXP

The NXP TJA1042AT/0Z is a high-speed CAN bus transceiver with one transmitter and one receiver, a maximum data rate of 5 Mb/s, and an SOIC-8 surface-mount package. Its 4.5 V to 5.5 V supply range and -40°C to +150°C operating-temperature range make it appropriate for demanding industrial and automotive communication systems. The TJA1042AT/0Z also provides Standby-mode operation, including the bus-wake-up capability described for the TJA1042 family. A CAN transceiver is an interface IC that connects a CAN protocol controller, such as a microcontroller with an integrated CAN controller, to a physical two-wire CAN bus. The transceiver converts the controller's logic-level transmit command into a differential CANH/CANL bus signal and converts the differential bus voltage into a logic-level receive output. Within the product hierarchy, a CAN transceiver belongs to the interface IC class, the CAN interface subclass, and ultimately the broader semiconductor category. The TJA1042AT/0Z provides a data rate of up to 5 Mb/s, one CAN transmitter, one CAN receiver, and a specified operating supply current of 80 mA. Its 4.5 V minimum and 5.5 V maximum supply voltages support conventional 5 V automotive and industrial CAN systems. Standby mode helps reduce system consumption when the bus is inactive, while the family's bus-wake-up behavior supports systems that must detect remote bus activity. The family is designed for high-speed CAN applications in the automotive industry and includes differential transmit and receive capability between a CAN controller and a two-wire bus. NXP describes the TJA1042 as a third-generation high-speed CAN transceiver. Its SOIC-8 construction provides a conventional surface-mount option for PCBs requiring a small, widely supported package, although the actual exposed-pad and soldering details should be confirmed against the manufacturer package drawing. Typical uses include automotive body and powertrain control modules, industrial automation equipment, robotics controllers, building automation gateways, and other embedded systems that exchange data over a CAN bus. In these systems, the controller handles CAN frames and protocol timing, while the TJA1042AT/0Z handles the physical-layer differential signaling. Its 5 Mb/s capability accommodates high-speed CAN traffic, and its -40°C to +150°C specification supports wide environmental ranges. PCB design should preserve the transceiver's supply decoupling, ground connection, controller-interface traces, and CAN bus routing. Place the supply capacitor close to the device and keep the CANH and CANL route as a closely coupled differential pair. The bus conductors require suitable termination, protection, and common-mode considerations; exact resistor and capacitor values are application-dependent and are not specified by the verified source excerpts. This product record combines the verified NXP datasheet information with distributor availability, package details, temperature limits, supply limits, and a bulk pricing schedule as of 2026-10-28. It also distinguishes the TJA1042AT/0Z from related TJA1042 and modern TCAN transceiver options so engineers can assess PCB compatibility and functional differences before selecting a replacement.

RFQ İletişim
TJA1042AT/3/0Z - 5Mbps CAN Transceiver | NXP
TJA1042AT/3/0Z

TJA1042AT/3/0Z - 5Mbps CAN Transceiver | NXP

The NXP Semiconductors TJA1042AT/3/0Z is a high-speed CAN transceiver with a 5 Mbps maximum data rate, differential CAN bus transmit and receive functions, a 5 V supply, and an 8-pin SOIC package. It provides the physical-layer interface between a CAN protocol controller and a two-wire CAN network, with the /3 version supporting a VIO supply for direct interfacing with 3.3 V or 5 V controller logic. A CAN transceiver is an interface IC that converts logic-level TXD and RXD signals into the differential CANH and CANL bus signals used by Controller Area Network systems. Within the hierarchy of CAN interface ICs, physical-layer transceivers connect automotive and industrial network controllers to the bus while adding bus protection, standby behavior, and standardized digital interfaces. The TJA1042 family is specifically designed for high-speed automotive CAN networks. Principal features include a maximum CAN data rate of 5 Mbps, one-transceiver one-receiver organization, differential bus output, low-power Standby mode, and VIO support in the /3 version. The separate VIO rail allows the controller-facing pins to operate from a lower voltage while CANH, CANL, and the transceiver core use the 5 V supply. The Arrow product listing identifies the device as an automotive AEC-Q100 8-pin SOIC transceiver. The TJA1042AT/3/0Z uses pin 5 as VIO rather than the SPLIT common-mode stabilization function found on the TJA1042T version. This distinction is important during replacement because the two suffix families do not have identical pin 5 functions. The /3 device also provides bus wake-up capability and passive behavior when unpowered, characteristics that support low-power automotive networking and robust bus integration. Typical applications include automotive body and chassis control modules, powertrain and gateway controllers, industrial CAN equipment, robotics, and embedded transport systems. It is particularly suitable where a microcontroller or dedicated CAN controller requires a 5 Mbps physical interface while its digital I/O operates at 3.3 V. The low-power Standby function helps reduce current consumption when the node is not actively communicating. When laying out a circuit, place the transceiver close to the CANH and CANL connector, keep the bus traces short and matched, and provide the decoupling and common-mode components recommended by the NXP TJA1042 manufacturer datasheet. Verify that VIO is connected correctly on the /3 version and that PCB exposure, automotive qualification, and temperature requirements match the intended installation. This page combines the NXP manufacturer datasheet, product listings, verified drop-in candidates, interface comparisons, and practical PCB guidance. It helps engineers identify the correct /3 variant, distinguish VIO from SPLIT implementations, and plan a CAN transceiver layout without relying on a generic SOIC-8 pinout.

RFQ İletişim
TJA1042ATK/3/0Z - 5Mbps CAN FD Transceiver | NXP
TJA1042ATK/3/0Z

TJA1042ATK/3/0Z - 5Mbps CAN FD Transceiver | NXP

NXP Semiconductors TJA1042ATK/3/0Z is a high-speed CAN and CAN FD transceiver with a maximum data rate of 5 Mbit/s, a 5 V transceiver supply, and an 8-HVSON exposed-pad package measuring 3 x 3 mm. It provides the physical-layer interface between a CAN protocol controller and a two-wire CAN bus, combining high-speed data transfer with low-power standby operation. A CAN transceiver is an interface IC that converts logic-level controller signals into differential CAN bus levels and reconstructs bus signals for the controller. Within the communication hierarchy, the TJA1042ATK/3/0Z belongs to the CAN transceiver class, interface ICs, wired-communication semiconductors, and automotive electronics. Its differential bus interface supports robust automotive networking while the transceiver handles electrical protection and bus interfacing. Key characteristics include support for communication rates up to 5 Mbit/s, a 4.5 V to 5.5 V transceiver operating range, and a low-power Standby mode with bus wake-up capability. The automotive-grade version is identified as AEC-Q100 compliant in the product listing. Its 8-HVSON package uses an exposed pad to improve heat dissipation while keeping the PCB footprint compact. The TJA1042 family is designed for reliable CAN and CAN FD communication with improved electromagnetic compatibility and electrostatic-discharge performance. The passive behavior of the bus pins when the device is unpowered helps a connected node avoid disrupting communication from other operating nodes. These characteristics are useful in distributed automotive and industrial control networks where cable length, electromagnetic interference, and partial power loss are important system considerations. Typical applications include automotive body and chassis control modules, industrial CAN gateways, vehicle diagnostic interfaces, battery-management systems, and distributed automation controllers. A CAN protocol controller or MCU with an integrated CAN controller connects to the TJA1042 through TXD, RXD, and enable-related pins, while CANH and CANL connect to the bus through the network termination and protection scheme. For PCB implementation, place the transceiver close to the CAN bus connector and keep the CANH and CANL traces short, symmetric, and free from switching nodes. Follow the manufacturer pin and layout guidance when connecting the exposed pad, supply decoupling, split-capacitor option, bus termination, and protection components. Account for the common-mode and transient-voltage environment of an automotive bus. This page combines the exact ordering information, electrical envelope, automotive qualification, package details, drop-in alternatives, application guidance, and design considerations needed to evaluate the TJA1042ATK/3/0Z before PCB implementation or sourcing.

RFQ İletişim
TJA1042T - 1 Mbps High-Speed CAN Transceiver | NXP Semiconductors
TJA1042T

TJA1042T - 1 Mbps High-Speed CAN Transceiver | NXP Semiconductors

Buy the NXP TJA1042T 1 Mbps high-speed CAN transceiver in an 8-pin SOIC with standby mode. Compare alternatives, verify pinout and lifecycle, and request current supply.

RFQ İletişim
TJA1042T/1J - High-Speed CAN Transceiver | NXP | Automotive
TJA1042T/1J

TJA1042T/1J - High-Speed CAN Transceiver | NXP | Automotive

The NXP TJA1042T/1J is a high-speed CAN transceiver with standby mode, providing the physical-layer interface between a CAN protocol controller and a differential two-wire CAN bus. The device is packaged as an 8-pin SOIC and is identified by DigiKey as a 1/1 half CAN-bus transceiver. The verified NXP product page describes it as a high-speed CAN transceiver with standby mode, while the manufacturer datasheet states that it supplies differential transmit and receive capability for automotive CAN systems. A CAN transceiver is an interface IC that converts logic-level TXD and RXD signals into the dominant and recessive voltage levels carried by a CAN bus. It also places the bus-side driver and receiver between the controller and the physical network, helping the controller communicate over a robust multi-node differential bus. The TJA1042 family belongs to the broader CAN transceiver, communication interface, interface IC, and semiconductor hierarchy. The key verified feature set is high-speed CAN operation, differential transmit and receive, standby operation, 8-pin SOIC packaging, and automotive-oriented application positioning. The standby function is useful when a node must reduce activity while retaining the CAN interface. The exact maximum data rate, supply range, loop delay, bus fault behavior, thermal limits, and electrical thresholds are not present in the supplied verified excerpts, so those values must be confirmed from the complete manufacturer datasheet before design release. The TJA1042 is intended for automotive electronic control units, body controllers, powertrain controllers, gateway modules, instrument clusters, and other embedded systems that use a CAN protocol controller. In a typical circuit, the MCU CAN controller connects to TXD and RXD, while CANH and CANL connect to the external bus through the board's approved network interface and termination arrangement. The transceiver is the boundary between digital controller signaling and the differential physical bus. Designers should verify the exact NXP ordering code, supply voltage, transceiver mode timing, bus termination, common-mode environment, loop delay, and external-component recommendations against the complete TJA1042 datasheet. Because the supplied web data does not expose a complete pin-level table, pricing schedule, compliance declaration, or lifecycle statement, those items are marked as needing verification rather than inferred. The TJA1042T/1J is best evaluated by engineers who need a standby-capable, high-speed CAN physical-layer device in an SOIC footprint.

RFQ İletişim
TJA1042T/1U - High-Speed CAN Transceiver | NXP | SOIC-8
TJA1042T/1U

TJA1042T/1U - High-Speed CAN Transceiver | NXP | SOIC-8

The NXP Semiconductors TJA1042T/1U is a high-speed CAN transceiver with standby mode, packaged in an 8-pin SOIC. It provides the physical-layer interface between a CAN protocol controller and a differential two-wire CAN bus. The device supports the transmit, receive, standby, split and bus-fault functions expected from a high-speed automotive CAN transceiver, while its SOIC-8 format supports conventional surface-mount PCB assembly. A CAN transceiver is an interface IC within the broader Controller Area Network hierarchy. It converts logic-level TXD and RXD signals from a CAN controller into the dominant and recessive differential levels carried by CANH and CANL. Conversely, it converts the differential bus voltage into a logic-compatible receive signal. This physical-layer function allows a microcontroller or dedicated CAN controller to communicate reliably with other nodes on a shared network. The TJA1042T/1U differentiates itself through its standby operating mode and split functionality. Standby mode lets the node reduce activity when it is not required to participate fully in bus communication. The split function is associated with stabilizing recessive bus behavior and can be important in systems containing more than one CAN node. NXP markets the TJA1042T family for high-speed CAN applications in the automotive industry. The TJA1042T/1U is identified as an NRND product on the official NXP product page. NRND means the product is not recommended for new designs, so engineers should evaluate the lifecycle position and any successor named by NXP before committing a new production platform to this MPN. Existing designs may still use the part, but procurement and long-term availability require confirmation from authorized distributors. Typical uses include distributed automotive control modules, body electronics, electric vehicle subsystems, industrial CAN gateways, sensor nodes and engine or transmission control units. The differential bus interface lets these systems exchange data reliably over distances and wiring arrangements that would be unsuitable for ordinary single-ended digital signaling. Local CAN-controller I/O voltage compatibility must also be checked during design review. PCB implementation requires care around the CANH and CANL connections. The two bus conductors should follow the impedance and routing guidance in the manufacturer datasheet, with a common-mode choke or split capacitor used only when the reference network requires it. Decoupling should be placed close to the supply pins, and unused device functions must be connected exactly as specified in the datasheet rather than according to generic transceiver schematics. This page consolidates the verified NXP product information, distributor package identification, sourcing context, lifecycle status and practical design guidance. It distinguishes documented facts from values that require confirmation from the current manufacturer datasheet, helping engineers evaluate the TJA1042T/1U without treating incomplete distributor snippets as complete electrical specifications.

RFQ İletişim
TJA1042T/3 - 5Mbit/s CAN Transceiver, SOIC-8 | NXP
TJA1042T/3

TJA1042T/3 - 5Mbit/s CAN Transceiver, SOIC-8 | NXP

The NXP Semiconductors TJA1042T/3 is a high-speed CAN transceiver with Standby mode, providing a physical-layer interface between a CAN protocol controller and a two-wire CAN bus. It supports CAN FD fast-phase communication at data rates up to 5 Mbit/s, operates from a 4.5V to 5.5V supply, and supports 3V to 5V microcontroller interfacing through its VIO interface. The device is packaged in an 8-pin SOIC. A CAN transceiver is an interface IC that converts logic-level signals from a CAN controller into the dominant and recessive voltage states used on a differential CAN bus. It also converts bus levels into receive data for the controller. The TJA1042 belongs to the high-speed CAN transceiver category within the broader network-interface IC and automotive communication hierarchy. The TJA1042T/3 provides differential transmit and receive capability, a low-power Standby mode, and bus wake-up capability. It can remain passive when unpowered, helping the connected CAN network enter a low-current state. The VIO interface allows direct connection to microcontrollers operating from 3V to 5V, while the main transceiver supply operates from 4.5V to 5.5V. The TJA1042 implements the CAN physical layer defined by ISO 11898-2:2016 and the SAE J2284-1 through J2284-5 specifications identified in the NXP documentation. These standards establish the electrical behavior expected of high-speed CAN nodes, including bus signaling, termination, timing, and fault behavior. Typical uses include automotive body and comfort modules, industrial CAN gateways, engine controllers, battery-management systems, and embedded control units that communicate over a two-wire CAN network. Its 5Mbit/s capability makes it appropriate for systems that combine conventional CAN traffic with the faster data phase of CAN FD. Designers should connect the CANH and CANL pins to the protected bus network, provide the bus-side termination specified by the system architecture, and use a suitable common-mode choke or ESD protection where required. VIO should be connected to the microcontroller interface supply, while VCC must satisfy the 4.5V to 5.5V operating range. This page combines the manufacturer specifications, package information, interface standards, drop-in candidates, and application guidance needed to evaluate the TJA1042T/3 as a high-speed CAN physical-layer interface for automotive and industrial control systems.

RFQ İletişim
TJA1042T/3/1J - High-Speed CAN Transceiver w/ Standby, SOIC-8 | NXP
TJA1042T/3/1J

TJA1042T/3/1J - High-Speed CAN Transceiver w/ Standby, SOIC-8 | NXP

The NXP TJA1042T/3/1J is a high-speed Controller Area Network (CAN) transceiver providing the physical interface between a CAN protocol controller and a two-wire CAN bus, supplied in an 8-pin SOIC package with a maximum data rate of 1 Mbit/s. It operates from a 4.5 V to 5.5 V VCC supply and supports direct interfacing to microcontrollers with supply voltages as low as 3 V through a dedicated VIO pin (variant /3). The device features low-current Standby mode with bus wake-up capability and ideal passive behavior to the CAN bus when VCC is off. A CAN transceiver (also called a CAN bus transceiver or CAN physical layer device) is a protocol-bridge IC that converts the differential digital signaling on a CAN bus into the single-ended TX/RX logic levels expected by a microcontroller's CAN protocol controller. CAN transceivers sit one layer below the CAN data link layer in the OSI model and are essential for any automotive, industrial, or embedded system that communicates over the Controller Area Network standard (ISO 11898). Without a transceiver the MCU's CAN controller cannot drive or receive the bus. Key features include excellent electromagnetic compatibility (EMC) and electrostatic discharge (ESD) performance, an SPLIT-pin-free /3 variant with a VIO reference for 3.3 V MCUs, and pin compatibility with the classic TJA1040, PCA82C250, and PCA82C251. The transceiver supports bus wake-up patterns, thermal shutdown, a dominant time-out that prevents bus lockup if the controller fails, and an unpowered bus node that does not disturb the network. The TJA1042T/3/1J also provides a low-current Standby mode in which the bus is continuously monitored for wake-up frames. Internally the device uses a differential driver with slope control to minimize EMI, very-low-drop receiver comparators, and an integrated VIO reference that allows the logic I/O domain of the chip to match the host MCU's supply. Compared to its predecessor TJA1040, the TJA1042 reduces quiescent current, improves ESD to at least 6 kV HBM, and adds the VIO pin to decouple digital I/O levels from VCC for 3.3 V microcontrollers. Typical applications include automotive body and chassis ECUs, industrial CANopen and DeviceNet nodes, elevator controllers, building automation gateways, and any CAN node that must interface to a 3.3 V microcontroller without level shifters. The part is widely used as the physical-layer upgrade for designs that previously used TJA1040, PCA82C250, or PCA82C251. When designing with this part, place a 100 nF decoupling capacitor as close as possible to the VCC pin and a 100 nF cap on VIO; add a common-mode choke and split termination (60 ohm + 5.6 nF at each end) on bus lines operating above 500 kbit/s in noisy environments. Tie the STBY pin high for Normal mode and monitor CANH/CANL for short-to-ground or short-to-VCC conditions. The /3 variant replaces the SPLIT pin of the original TJA1042T with a VIO pin, so confirm that the PCB land pattern matches pin 5 = VIO. This page synthesizes distributor pricing, drop-in alternatives from the same TJA1042 family and competitor cross-references such as TCAN1042, plus practical design notes not found in the manufacturer datasheet.

RFQ İletişim
TJA1042T/3/1U - 5 Mbit/s CAN FD Transceiver | NXP
TJA1042T/3/1U

TJA1042T/3/1U - 5 Mbit/s CAN FD Transceiver | NXP

NXP TJA1042T/3/1U is a high-speed CAN transceiver with Standby mode, providing an interface between a CAN protocol controller and a two-wire CAN bus. The device supports reliable CAN and CAN FD communication at data rates up to 5 Mbit/s and is packaged in an 8-pin SOIC-style package. Its automotive temperature grade and 3 V microcontroller interface capability suit vehicle networking systems that require low-power standby operation. A CAN transceiver is the physical-layer interface within a Controller Area Network communication hierarchy. It converts logic-level TXD and RXD signals into balanced differential bus levels on CANH and CANL, while also providing bus dominance, recessive-state detection, and controller-side logic interfacing. The TJA1042 therefore belongs to the CAN physical-layer transceiver, interface IC, and automotive communication semiconductor categories. The TJA1042T/3/1U supports data rates up to 5 Mbit/s, includes a low-power Standby mode, and provides improved electromagnetic compatibility and electrostatic-discharge performance. Its /3 variant is intended for direct interfacing with microcontrollers operating from supply voltages down to 3 V. Pin 5 provides the VIO function instead of the SPLIT function found on certain other TJA1042 variants, making the ordering-code distinction important during PCB design and replacement planning. The transceiver integrates CAN bus driver and receiver functions with controller-facing logic inputs and outputs. VIO supports compatible microcontroller interfacing, while RXD reports the received bus state to the CAN controller. CANL and CANH provide the differential physical bus connection, and VCC supplies the transceiver. This integration allows a CAN controller to communicate over a robust two-wire bus without implementing the bus-line driver and receiver externally. Typical uses include automotive body and comfort modules, powertrain controllers, electric-vehicle control units, diagnostic gateways, industrial CAN equipment, and CAN FD nodes. The 5 Mbit/s capability is particularly useful where the network carries larger payloads or enables CAN FD data-phase communication. Standby mode supports systems that need to retain low-power behavior while reducing activity when the node is not communicating. When designing around the TJA1042T/3/1U, verify that the PCB footprint accommodates the 8-pin SOIC package and that the controller supply level matches the VIO arrangement of the /3 variant. CAN bus layouts should follow the routing and termination guidance in the manufacturer datasheet, including correct 120-ohm termination only at the physical ends of the bus. This product overview combines the verified NXP family characteristics with application guidance, pin-role clarification, practical layout considerations, and qualified replacement comparisons. It is intended to help engineers distinguish the TJA1042T/3/1U from related SOIC-8 CAN transceivers whose logic, supply, standby, or bus-behavior details differ.

RFQ İletişim
TJA1042TK/3/1J - 5 Mbit/s CAN FD Transceiver | NXP
TJA1042TK/3/1J

TJA1042TK/3/1J - 5 Mbit/s CAN FD Transceiver | NXP

NXP Semiconductors TJA1042TK/3/1J is a high-speed Controller Area Network transceiver with a maximum supported data rate of 5 Mbit/s, CAN FD compatibility, and a low-power Standby mode. The device is packaged in an 8-pin HVSON package measuring 3 mm by 3 mm and interfaces a CAN protocol controller with a physical two-wire CAN bus. A CAN transceiver is an interface IC that converts logic-level signals from a CAN controller into the differential dominant and recessive states carried by a CAN bus. It also converts received bus states into signals the controller can interpret. The TJA1042 family belongs to the CAN transceiver hierarchy within interface ICs, semiconductors, and automotive communication electronics. The TJA1042 supports reliable CAN and CAN FD communication up to 5 Mbit/s. Its Standby mode provides a low-power operating state, while the 3.3 V VIO connection supports communication with CAN controllers operating at that logic level. The manufacturer identifies improved electromagnetic compatibility and electrostatic-discharge performance as principal benefits of the family. The TJA1042TK/3/1J ordering code identifies the 8-HVSON 3 mm by 3 mm package configuration and a 3.3 V VIO variant. The package offers a compact surface-mount implementation for automotive electronics, but its exposed-pad construction and limited thermal path require careful PCB layout. CAN bus traces should be routed as a controlled differential pair with appropriate termination and common-mode considerations. Typical uses include automotive CAN FD gateways, body and comfort controllers, electric-vehicle subsystems, industrial CAN equipment, and battery-management systems with 3.3 V CAN controllers. The combination of 5 Mbit/s operation, CAN FD support, and Standby mode is useful where high communication bandwidth and reduced inactive-state consumption are both important. Use the manufacturer pin-description table when assigning PCB tracks and land patterns, and confirm the controller voltage, bus termination, transceiver supply levels, and standby-control polarity before releasing a board layout. The small HVSON package also requires adequate copper around the thermal pad and controlled assembly-planarity conditions. This page organizes the TJA1042TK/3/1J specifications, verified source links, application guidance, engineering design notes, and compatibility considerations to support faster component selection and PCB implementation.

RFQ İletişim
TJA1043AT/0Z - 5 Mbps CAN Transceiver | NXP | Automotive
TJA1043AT/0Z

TJA1043AT/0Z - 5 Mbps CAN Transceiver | NXP | Automotive

The NXP TJA1043AT/0Z is a high-speed CAN transceiver supporting data rates up to 5 Mbps in a 14-pin SOIC package. It operates from a 4.5 V to 5.5 V supply and provides Normal, Sleep, and Standby operating modes for power-managed automotive and industrial CAN networks. The part is identified as an AEC-Q100 automotive-grade device and is supplied in tape-and-reel packaging. A CAN transceiver is the physical-layer interface between a host controller and a Controller Area Network bus. The CAN standard assigns the physical signaling, termination, dominant and recessive states, and bus fault behavior that allow nodes to communicate reliably over a wired network. A CAN interface IC therefore bridges digital controller signals and the differential CANH and CANL bus conductors. The TJA1043AT/0Z family is designed for high-speed communication while adding fail-safe and diagnostic capabilities intended to improve system reliability. Its supported modes give a host controller opportunities to reduce power use when communication is not required. The verified product data specifies 5 Mbps operation, a 4.5 V to 5.5 V DC operating range, Normal/Sleep/Standby modes, AEC-Q100 qualification, and a 14-pin SOIC package. The TJA1043 product family combines a CAN transmitter, CAN receiver, bus-driver enable control, and low-power management in one interface device. This integration reduces the number of discrete components required around a CAN controller and centralizes bus-domain behavior. Because CAN bus reliability depends on correct termination and layout, the transceiver remains only one element of the complete network design. Typical uses include automotive body and comfort modules, industrial automation equipment, engine controllers, gateways, sensors, and embedded control systems. A controller such as the site's ISO1500DBQ can provide an isolated interface layer, while the TJA1043AT/0Z handles the non-isolated physical CAN connection. Its 5 Mbps capability supports communication-intensive vehicle networks and industrial equipment. Designers should verify the complete pinout against the current NXP datasheet before layout because the supplied verified data confirms the 14-pin package but does not expose individual pin assignments. CANH and CANL routing also requires controlled impedance, a common-ground strategy, correct 120 ohm termination at the physical bus endpoints, and protection appropriate for the target environment. This product page consolidates current distributor availability, the confirmed electrical envelope, automotive qualification, packaging information, and practical interface-selection guidance. It also distinguishes verified drop-in candidates from broader functional alternatives so engineers can assess PCB reuse, power-mode behavior, and bus-system compatibility before committing to a replacement.

RFQ İletişim
TJA1043ATK/0Y - High-Speed CAN Transceiver | NXP | 14-HVSON
TJA1043ATK/0Y

TJA1043ATK/0Y - High-Speed CAN Transceiver | NXP | 14-HVSON

The NXP Semiconductors TJA1043ATK/0Y is a high-speed Controller Area Network transceiver packaged in a 14-HVSON package measuring 3 x 4.5 mm. It provides one CAN transmit and one CAN receive path for connecting a host controller to a high-speed CAN bus. According to the manufacturer product page, the device combines fail-safe operation, diagnostic features, and advanced power management to support dependable automotive and industrial communication systems. A CAN transceiver is the physical-layer interface between a CAN controller and the differential CAN bus. It converts logic-level transmit and receive signals into a robust differential bus waveform and provides the receive data back to the controller. As a single-transceiver device, the TJA1043ATK/0Y integrates a CAN transmitter, CAN receiver, bus biasing functions, and interface protection in one compact package. The principal differentiators of the TJA1043 family are its fail-safe and diagnostic capabilities together with advanced power-management functions. Fail-safe behavior is important in automotive networks because it helps define the transceiver state when the bus supply or bus line is absent. Diagnostic features support system-level fault detection by exposing bus-related conditions to the host electronics. These functions are more relevant than raw data-rate differences when the transceiver is selected for a new vehicle or industrial CAN network. The 14-HVSON package is intended for compact surface-mount assemblies. Its small 3 x 4.5 mm footprint supports high-density controller-unit and gateway layouts, although exposed-pad layout and thermal performance must follow the package recommendations in the manufacturer datasheet. Because the package is lead-free and very small, careful PCB footprint design, solderability verification, and assembly process control are essential. Typical uses include automotive electronic control units, body-comfort modules, powertrain controllers, industrial automation equipment, and CAN-based sensors. In these systems, the TJA1043ATK/0Y sits between the CAN controller and the bus connector, while external bus protection, decoupling, and common-mode choke elements are selected according to the network topology and electromagnetic-compatibility requirements. This page organizes the confirmed package and product information, provides practical application guidance, and separates documented TJA1043 characteristics from parameters that must be confirmed in the manufacturer datasheet. The datasheet remains the controlling document for pin assignments, electrical limits, timing values, recommended application circuits, and qualification information.

RFQ İletişim
TJA1043T - High-Speed CAN Transceiver, 1Mbps, SO-14 | NXP
TJA1043T

TJA1043T - High-Speed CAN Transceiver, 1Mbps, SO-14 | NXP

The NXP TJA1043T is a high-speed Controller Area Network (CAN) transceiver that provides the physical interface between a CAN protocol controller and a differential two-wire CAN bus, housed in a 14-pin SO (SOIC-14) package. It supports data rates up to 1 Mbps across the ISO 11898-2 / ISO 11898-5 compliant physical layer, and operates from a 5 V supply with very low standby and sleep-mode quiescent currents for ECU sleep-current budgets. The device provides differential transmit and receive capability and integrates dominant-timeout, bus-failure diagnostics, and thermal protection. A CAN transceiver (sometimes called a CAN physical layer or CAN PHY) is the analog interface between a digital CAN protocol controller (typically inside an MCU) and the differential CANH/CANL bus wires that carry data across a vehicle network. It belongs to the broader hierarchy of bus transceivers -> interface ICs -> wired communication ICs. Automotive ECUs (Electronic Control Units) require a certified transceiver that meets ISO 11898 EMC and ESD specifications; the TJA1043 family is a third-generation NXP design widely used in body, chassis, and powertrain CAN nodes. Key features include 1 Mbps maximum bit rate, ±8 kV HBM ESD on bus pins (per NXP datasheet figures), very low quiescent current in Sleep mode (typically a few microamps), an SPLIT pin for bus biasing when the bus is off, and three operating modes (Normal, Standby, Sleep) selectable via the EN and STBN pins. The IC operates across -40 °C to +125 °C ambient and is qualified to the automotive quality flow. Internally the TJA1043T uses a bipolar-CMOS-DMOS (BCD) process that combines 5 V analog drive strength on the bus with low-power digital logic. The receiver includes a wide common-mode range for excellent EMC immunity, and the transmitter incorporates slew-rate control to limit EMI on unshielded bus segments. Typical applications include automotive body control modules, gateway ECUs, chassis controllers, infotainment CAN nodes, and industrial CAN-FD ready nodes that need backward-compatible high-speed CAN. The wide common-mode range also makes it suitable for 12 V and 24 V battery systems in trucks and off-road equipment. When designing with this part, place a 100 nF decoupling capacitor close to VCC and respect the SPLIT-pin biasing network shown in the datasheet typical application. Verify bus termination (120 Ω at each end) and dominant-timeout behaviour when using a permanently dominant TXD input. This page synthesizes distributor pricing, drop-in alternative guidance, and practical design notes that complement the manufacturer datasheet and accelerate your component selection.

RFQ İletişim
TJA1043T-1J - High-Speed CAN Transceiver, 5Mbit/s | NXP
TJA1043T-1J

TJA1043T-1J - High-Speed CAN Transceiver, 5Mbit/s | NXP

The NXP TJA1043T-1J is a third-generation high-speed Controller Area Network (CAN) transceiver providing the physical interface between a CAN protocol controller and a differential two-wire CAN bus, supporting data rates up to 5 Mbit/s in a 14-pin SOIC package. It features VIO supply pin for direct interfacing with 3.3V microcontrollers, SPLIT voltage output for bus biasing stabilization, dedicated wake-up input, standby control (STBN), and an enable pin. The part is qualified for automotive networks and conforms to ISO 11898-2:2024 high-speed CAN physical layer requirements. A CAN transceiver is an interface IC that translates single-ended logic-level TXD/RXD signals from a microcontroller into the differential voltage signaling required on the CANH and CANL bus wires, while simultaneously protecting the controller from bus-side ESD and EMC events. Within the broader hierarchy, the TJA1043 belongs to the class of bus transceivers (also called physical-layer devices or PHYs), which sit between the data-link-layer CAN controller and the physical CAN bus medium in an in-vehicle network. Key features include very low quiescent current consumption in standby and sleep modes, passive bus behavior when supply is off (no reverse current into the bus), integrated thermal shutdown, and bus-pin ESD protection up to ±8 kV HBM. The VIO pin allows the logic supply to be tied directly to a 3.3V microcontroller without level shifters, simplifying mixed-voltage ECU designs. Typical applications include automotive body and powertrain ECUs, gateway modules, ADAS sensor nodes, industrial CAN automation networks, and CAN-FD backbone segments where bus termination biasing and EMC robustness are critical. The SPLIT pin stabilizes the recessive bus common-mode voltage, especially important in networks with multiple unpowered nodes. When designing with this device, keep the SPLIT pin terminated through a capacitor to ground per the datasheet reference design, and ensure the VIO and VCC rails are sequenced correctly to avoid latch-up during cold-crank events in 12V automotive systems.

RFQ İletişim
TJA1043T/1U - High-Speed CAN Transceiver | NXP
TJA1043T/1U

TJA1043T/1U - High-Speed CAN Transceiver | NXP

The NXP Semiconductors TJA1043T/1U is a high-speed CAN transceiver that provides the physical-layer interface between a CAN protocol controller and a two-wire CAN bus. The device is offered in a 14-pin small-outline package identified by distributor data as 14-SO, and the TJA1043 family includes standby and sleep operating modes for reducing activity when communication is not required. Its transceiver architecture handles CAN signal transmission, reception, bus termination, and controller interfacing. A CAN transceiver, also called a CAN physical-layer interface, converts logic-level TXD and RXD signals into the differential voltage used on a CAN network. In the larger electronics hierarchy, it belongs to the CAN interface IC family, within the broader category of interface ICs and communication semiconductors. The CAN bus itself is a robust two-wire communication network commonly used in automotive electronics, industrial automation, transportation, and embedded control systems. The TJA1043 provides separate TXD and RXD controller connections, control pins for standby and sleep behavior, and connections for the differential CANH and CANL conductors. The standby and sleep functions are useful in systems where low-power operation or controlled bus participation is required. The split-termination arrangement gives a board designer additional flexibility when configuring bus termination and EMC performance. Operationally, the transceiver is intended for use with a separate CAN controller rather than as a standalone bus node. The controller generates transmit data and receives decoded bus information, while the TJA1043 translates between controller logic and the physical CAN bus. Its high-speed CAN positioning makes it appropriate for systems requiring reliable communication over longer in-vehicle or industrial cable runs when the associated controller, termination network, and wiring satisfy the required bus conditions. Typical uses include automotive body and powertrain electronics, industrial automation equipment, robotics, elevator controls, building automation, and embedded CAN gateways. In these systems, the TJA1043 can sit between the physical bus and a controller such as a CAN controller MCU, an automotive communication processor, or an embedded communications bridge. Standby and sleep support helps designers balance responsive bus access against standby power. The primary design consideration is preserving correct CAN bus termination and signal integrity. The split termination network must be configured according to the manufacturer application guidance, and the PCB should provide a short return path to the transceiver ground pins. Designers should also verify controller logic levels, enable-state polarity, transceiver supply requirements, and bus topology before releasing a production design. This page consolidates the verified NXP and distributor references, distinguishes the available same-family and cross-brand drop-in candidates, and adds practical comparison, selection, and design guidance that is not consolidated on a typical distributor listing.

RFQ İletişim