Ürünler (44.000+)

TS339ID - Micropower Quad CMOS Comparator | STMicroelectronics
TS339ID

TS339ID - Micropower Quad CMOS Comparator | STMicroelectronics

STMicroelectronics TS339ID is a micropower quad CMOS voltage comparator with four independent open-drain outputs, a supply range of ±8 V to ±16 V, and a 14-pin SOIC package. Each comparator typically consumes 9 µA, while the device is designed for low-input-bias and low-input-offset-current measurements. A voltage comparator is an analog semiconductor that compares two input voltages and produces a digital logic result indicating which input is higher. The TS339ID belongs to the comparator hierarchy, combining four general-purpose channels in one package. Its CMOS construction reduces current consumption compared with a conventional bipolar LM339, while the open-drain outputs support wired logic, level translation, and systems using external pull-up resistors. Each channel provides non-inverting and inverting inputs. Key characteristics include extremely low input bias current, a typical input offset current of 1 pA, and typical input impedance of 10^12 ohms. The TS339ID is pin-to-pin and functionally compatible with the bipolar LM339 device. Its typical response time is 1.5 µs for a 5 mV overdrive, making it suitable for threshold detection rather than high-speed signal-chain comparison. The open-drain output architecture requires an external pull-up resistor when a logic-high level is needed. Because the output stage can pull the node low but cannot actively drive it high, several comparator outputs can be combined in a wired-AND arrangement. This characteristic is useful for supervision, window detection, and fault signaling, although circuit design must account for the pull-up value, output leakage, and bus rise time. Typical uses include power-supply sequencing, battery monitoring, overvoltage and undervoltage detection, temperature-control thresholds, industrial sensor interfaces, and simple digital control systems. The quad arrangement reduces board area and component count when four independent thresholds are required, particularly in industrial monitoring, instrumentation, and embedded-control equipment. Designers should verify input common-mode limits, output pull-up requirements, and absolute maximum supply voltage against the manufacturer datasheet before implementation. The open-drain node should include a pull-up to a valid logic rail, and unused inputs must be tied to a defined potential rather than left floating. PCB layout should keep sensitive input traces away from switching nodes and high-current return paths. This product overview combines the exact TS339ID characteristics with practical guidance for open-drain logic, threshold detection, PCB implementation, and comparison against pin-compatible LM339-family devices. It also organizes the available technical information for engineers evaluating power consumption, response time, input impedance, package compatibility, and lifecycle-sensitive redesigns.

RFQ İletişim
TS339IN - Micropower Quad CMOS Comparator | STMicroelectronics
TS339IN

TS339IN - Micropower Quad CMOS Comparator | STMicroelectronics

The STMicroelectronics TS339IN is a micropower quad CMOS voltage comparator with four independent channels, a 1.35 V to 16 V operating supply range, and a 14-DIP package. It features a 1 pA input bias current, 5 mV input offset voltage, and 1.5 microsecond response time, making it suitable for low-power signal conditioning. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital output indicating which input is higher. The TS339IN belongs to the comparator hierarchy, where four open-drain channels can monitor thresholds, detect crossings, supervise signals, or support feedback control. Its CMOS implementation provides low input bias current and low power consumption compared with classic bipolar comparator families. The TS339IN includes four general-purpose comparator channels with CMOS, open-drain outputs. The 1.35 V to 16 V supply range allows operation from low-voltage battery systems through conventional industrial rails, while the 1 pA typical input bias current reduces loading on high-impedance sensors. A 5 mV typical input offset voltage defines the baseline comparison accuracy, and the 1.5 microsecond response time supports threshold decisions without adding substantial propagation delay. Each comparator channel operates independently, allowing one device to implement four related decisions. The open-drain output architecture requires an external pull-up resistor, but it also provides flexible output-interface options. Designers can use the pull-up voltage to match downstream logic levels and can connect open-drain outputs in wired-AND configurations where appropriate. Dual-supply operation is supported up to a total supply span of 8 V. Typical uses include industrial sensor interfaces, battery-powered monitoring, digital control thresholds, window comparators, and general signal-conditioning systems. The low input bias current is particularly useful with resistive dividers, sensor outputs, and leakage-sensitive measurement circuits. The 14-DIP format also supports through-hole assembly and repairable industrial equipment where surface-mount packages would be inconvenient. When designing around the TS339IN, account for the open-drain output when selecting pull-up values and external logic supply levels. Keep input and output paths away from noisy switching nodes, and verify offset and common-mode behavior against the minimum signal separation required by the application. The operating range of -40°C to +125°C supports industrial temperature environments when the complete assembly is properly qualified. This product data combines the electrical characteristics, package details, cross-reference options, and practical design guidance needed to evaluate TS339IN. It also organizes pin assignments, application considerations, and compatible alternatives into a concise engineering reference for prototype development and production sourcing.

RFQ İletişim
TS339IPT - Micropower Quad Open-Drain Comparator | ST
TS339IPT

TS339IPT - Micropower Quad Open-Drain Comparator | ST

The STMicroelectronics TS339IPT is a micropower quad CMOS voltage comparator with four open-drain outputs, extremely low typical supply current of 9 μA per comparator, and operation across a 3 V to 16 V supply range. The device is packaged in a 14-pin TSSOP package and is intended for low-voltage, low-power signal-conditioning systems. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input exceeds the inverting input. The TS339 belongs to the comparator hierarchy, combining four independent comparator channels with CMOS input stages and open-drain outputs. The TS339 family provides a practical alternative to higher-current bipolar LM339-family comparators in battery-powered and portable equipment. Key features include four comparator channels, a typical input common-mode range extending from ground to VCC minus 1.5 V, an output sink capability of 40 mA, and open-drain outputs that can be pulled up to a chosen external voltage. The low 9 μA typical current per comparator supports low-power sensing, while the 16 V maximum supply rating permits operation from a 3 V supply through higher-voltage industrial rails. These characteristics make the device suitable for threshold detection, battery monitoring, signal conditioning, and sensor interfaces. The open-drain architecture provides flexible output voltage levels but requires an external pull-up resistor on every output. The pull-up resistor establishes the high output level, while the output transistor actively pulls the line toward ground. This arrangement permits wired logic, level translation, and wired-AND behavior, although designers must account for the rise time created by the resistor and total bus capacitance. Input common-mode and output-level requirements must be checked against the actual supply voltage. Typical applications include portable battery monitoring, industrial sensor interfaces, window or level comparators, overvoltage detection, and low-power control systems. Because the TS339IPT is specified for the industrial temperature range, it can also be used in equipment exposed to temperatures from −40 °C to +125 °C. The 14-pin TSSOP package supports compact, surface-mount assembly but is relatively narrow and requires careful component placement. When designing a PCB around the TS339IPT, route the comparator inputs away from switching nodes and provide a short, quiet ground reference for each sensing point. Place pull-up resistors close to the corresponding open-drain outputs to minimize trace capacitance and improve switching speed. Confirm that the logic high generated by the pull-up meets the receiving device's input threshold, and verify that no signal connected to either comparator input exceeds the datasheet's absolute maximum ratings. This page combines the TS339IPT's principal electrical characteristics, verified package and distributor information, application guidance, comparison data, and practical replacement considerations to support faster component selection and board-level design.

RFQ İletişim
TS3702CD - Micropower Dual CMOS Comparator | STMicro
TS3702CD

TS3702CD - Micropower Dual CMOS Comparator | STMicro

The STMicroelectronics TS3702CD is a dual micropower CMOS voltage comparator with 9 uA typical supply current per comparator, a 2 us typical response time, and push-pull outputs, packaged in an 8-pin SOIC. The device provides two independent comparators with high input impedance, making it suitable for low-power sensing and threshold-detection circuits. A voltage comparator is an analog integrated circuit that compares an input voltage against a reference voltage and changes its digital output state when the compared signals cross. The TS3702 belongs to the comparator class within analog and mixed-signal semiconductors. Its push-pull CMOS outputs eliminate the external pull-up resistor normally required by open-collector comparators such as the bipolar LM393, reducing component count and simplifying output interfacing. The TS3702 operates from single or dual supplies and supports input common-mode ranges extending below and above the supply rails. Typical supply current is 9 uA per comparator, approximately twenty times lower than a bipolar LM393 according to the manufacturer datasheet. Input impedance is 10^12 ohms typical, helping minimize loading on high-impedance sensors. Maximum input offset voltage is listed as 6.5 mV, so applications requiring tighter threshold accuracy should include offset and propagation-delay error in the system budget. Each channel contains an input stage, a logic decision element, and a CMOS push-pull output driver. The push-pull stage sources or sinks output current, allowing direct connection to CMOS logic inputs. Because the output actively drives both states, the device does not need a pull-up resistor, although PCB design should still provide adequate output-current margin and account for the input capacitance of the following stage. Typical uses include battery-powered threshold detection, window comparators, sensor signal conditioning, overvoltage monitoring, temperature-setpoint control, and portable instrumentation. The dual-channel configuration also allows one package to implement a two-threshold window monitor or compare two independent sensor signals without adding a second comparator package. For low-noise analog signals, keep comparator input traces short, place the input reference network close to the device, and avoid routing them beside switching-node traces. Add supply-bypass capacitance near the power pins and verify that the output state never conflicts with another push-pull driver. Because the output is actively driven, do not connect two comparator outputs together without an isolation device. This page combines package and pin information with application guidance, drop-in candidate evaluation, comparison parameters, and practical design notes that help engineers move from datasheet review to a working low-power analog front end.

RFQ İletişim
TS3702CN - 9µA Dual CMOS Comparator | STMicroelectronics
TS3702CN

TS3702CN - 9µA Dual CMOS Comparator | STMicroelectronics

The STMicroelectronics TS3702CN is a micropower dual voltage comparator featuring 9 µA typical supply current per comparator, a 1.5 µs response time, and a 6.5 mV maximum input offset voltage. The device is packaged in an 8-pin DIP and uses a CMOS push-pull output stage. Its two independent channels support differential input comparisons with single or dual power-supply operation. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the measured relationship crosses a defined threshold. The TS3702 belongs to the comparator hierarchy within analog signal-conditioning integrated circuits. Two integrated channels in one package provide a practical way to monitor two thresholds, control one analog system, or implement complementary sensing functions while reducing board area. The TS3702's principal advantages are its very low 9 µA typical current consumption per comparator, CMOS input characteristics, and push-pull outputs. Unlike the open-collector outputs used by conventional bipolar comparators such as the LM393 family, push-pull outputs can drive a defined high or low state without an external pull-up resistor. This can simplify output interfacing and reduce board space, although the resulting output current and transition behavior must remain within the device specifications. According to the STMicroelectronics manufacturer datasheet, the TS3702 can operate from a single positive supply or from split positive and negative supplies. The available comparison information identifies a dual-supply operating span from ±1.35 V to ±8 V, with ±3 V and ±5 V listed as typical dual-supply configurations. Input offset voltage is specified up to 6.5 mV, while propagation delay can reach 1.5 µs. These values position the device for low-power threshold detection rather than high-speed timing applications. Typical uses include battery-powered sensor conditioning, overvoltage and undervoltage detection, temperature-limit monitoring, window comparators, and low-power control loops. The two channels may also monitor complementary supply or signal thresholds. A push-pull output is particularly useful when the next stage requires a CMOS-compatible logic level and the added quiescent current of an external pull-up network is undesirable. Designers should verify input common-mode range, output-current limits, supply sequencing, and output behavior for every operating condition using the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, while comparator inputs require short, quiet traces that minimize coupling from switching nodes. The DIP package is suitable for through-hole assembly and prototypes, but modern compact products may require a different package variant and corresponding PCB redesign. This product page organizes the TS3702CN electrical characteristics, verified drop-in references, pin assignments, comparison parameters, and practical design guidance into one engineering-focused resource. It also distinguishes documented drop-in options from alternatives that require different packages or output structures, helping designers make a PCB-compatible sourcing decision.

RFQ İletişim
TS3702ID - Micropower Dual CMOS Comparator, 9uA, SOIC-8 | STMicroelectronics
TS3702ID

TS3702ID - Micropower Dual CMOS Comparator, 9uA, SOIC-8 | STMicroelectronics

The STMicroelectronics TS3702ID is a micropower dual CMOS voltage comparator that integrates two independent general-purpose comparators in an 8-pin SOIC-8 (SO-8) surface-mount package. Each channel consumes only 9 uA typical supply current, presents a 10^12 ohm typical input impedance and offers a 2.3 us typical response time, making it roughly twenty times lower in consumption than the classic bipolar LM393 reference circuit. A voltage comparator is an analog integrated circuit that compares two input voltages and switches its output according to which input is higher. As a sub-type of the amplifier family, a comparator sits between raw sensing elements and a digital control path: it belongs to the broader hierarchy of analog ICs, amplifiers and comparators, signal conditioning, and ultimately power management and interface ICs. Its job is to translate a small analog difference into a logic-level decision without introducing supply noise or consuming significant battery current. Key features of the TS3702ID include a push-pull CMOS output stage, which removes the external pull-up resistor normally required by open-collector comparators and saves both board area and standby current. The device accepts a single supply from 2.7 V to 16 V or dual supplies from +/-1.35 V to +/-8 V, operates down to ground at the input common-mode range, and draws only 1 pA typical input offset current. The manufacturer also specifies pin-to-pin and functional compatibility with the bipolar LM393, which eases migration between designs. Internally the TS3702ID uses a CMOS process, giving near-zero input bias current and rail-to-rail CMOS output levels rather than saturated bipolar levels. The push-pull stage sources and sinks current actively, so output transitions are fast and the logic levels remain valid at low supply voltages where open-collector comparators would need extra headroom to guarantee a valid high level. Typical applications include battery-powered sensor and threshold monitoring, window comparators for over/undervoltage detection, low-current alarm and wake-up circuits, portable instrumentation, and general-purpose level detection in industrial control boards. When designing with the TS3702ID, remember that the output stage is push-pull, not open-collector, so no external pull-up resistor should be added. Confirm the input common-mode limits against the actual supply voltage in the manufacturer datasheet, and keep the input bias network impedance high so the 1 pA offset current does not shift the threshold. This page consolidates the manufacturer datasheet figures, distributor availability, package details, drop-in alternatives and practical design notes into one engineering reference that goes beyond the raw component listing.

RFQ İletişim
TS3702IN - Micropower Dual Comparator | STMicroelectronics
TS3702IN

TS3702IN - Micropower Dual Comparator | STMicroelectronics

STMicroelectronics TS3702IN is a micropower dual CMOS voltage comparator with 9 µA typical supply current per comparator, 1.5 µs maximum response time, and 6.5 mV maximum input offset voltage in an 8-pin PDIP package. Its two independent comparator channels use push-pull CMOS outputs, eliminating the external pull-up resistor normally required by open-collector comparators. A voltage comparator is an analog mixed-signal component that compares two input voltages and produces a logic-level output indicating which input is higher. The TS3702IN belongs to the comparator hierarchy within integrated circuits and analog signal-conditioning ICs. Its micropower operating current makes it suitable for battery-powered equipment where continuous supply consumption must remain low, while its dual-channel configuration provides two comparison functions in one package. The principal features are low power consumption, CMOS-compatible push-pull outputs, low input offset voltage, and a response time suitable for general-purpose signal detection. According to the STMicroelectronics TS3702 product page, the TS3702 consumes 9 µA typical per comparator, approximately twenty times less than a bipolar LM393. The 16 V maximum supply rating provides headroom for conventional 5 V and low-voltage industrial systems, while the 600 pA input bias current limits disturbance of high-impedance sensing nodes. Internally, the device combines CMOS input stages with two independent comparator channels. The push-pull output architecture actively drives both logic states, making the outputs suitable for direct connection to compatible CMOS inputs. This differs from open-collector comparators, which require an external pull-up resistor and can present slower rising edges when additional capacitance must be charged. Board designers should still check the output timing and load limits in the manufacturer datasheet when driving unusually long traces or high-capacitance nodes. Typical uses include battery-powered threshold detection, sensor signal conditioning, overvoltage and undervoltage monitoring, window comparators, and simple control loops. A second application is industrial sensing where low 9 µA typical current per comparator helps limit standby consumption. The TS3702IN can also supervise a divided supply rail by comparing its scaled voltage against a reference derived from another node. The principal design consideration is logic compatibility. Push-pull outputs must not be tied together or connected to a pull-up resistor in the manner used with open-collector outputs. Input common-mode range, output voltage levels, and propagation-delay limits must be checked against the actual supply voltage and connected logic family before finalizing the circuit. This product page combines the manufacturer specifications with package, sourcing, and replacement guidance for engineers evaluating the TS3702IN. It also identifies drop-in alternatives that retain the same 8-pin through-hole footprint, helping PCB designers compare functionality without introducing an unintended package migration.

RFQ İletişim
TS3704CD - Quad Micropower CMOS Comparator | STMicroelectronics
TS3704CD

TS3704CD - Quad Micropower CMOS Comparator | STMicroelectronics

The STMicroelectronics TS3704CD is a four-channel micropower CMOS voltage comparator with push-pull outputs, supplied in a 14-pin SOIC package. It is designed for low-power signal conditioning and is identified by the manufacturer as an obsolete part. The device accepts a 3 V nominal supply according to distributor product records, operates from 0°C to 70°C in the standard TS3704CD grade, and uses a 35 uA typical comparator current as listed for the closely matched TLC3704CD family. A voltage comparator is an analog integrated circuit that compares an input voltage with a reference voltage and changes its digital output state when the relationship between the two signals changes. The TS3704CD belongs to the comparator hierarchy: analog mixed-signal IC, voltage comparator, quad comparator, and power-management signal-conditioning IC. Four independent channels in one package can reduce board area and simplify designs requiring several threshold-detection or overvoltage-monitoring functions. The TS3704CD uses CMOS circuitry to limit consumption and a push-pull output stage to eliminate the external pull-up resistor normally required with open-collector comparators. The four channels share a common supply arrangement within the package, while each comparator provides its own non-inverting and inverting inputs and logic output. This makes the device applicable to threshold crossings, sensor interfaces, signal conditioning, and general-purpose digital logic interfaces. According to the manufacturer datasheet, the TS3704 is a micropower quad CMOS voltage comparator whose typical current is approximately 9 uA per comparator, while the identified TLC3704 comparison records state 35 uA. Push-pull outputs can drive CMOS-compatible loads directly and transition without the passive pull-up network associated with open-drain comparators. Designers should still check output current, supply voltage, input common-mode range, and output levels for each operating condition before reuse. Typical uses include battery-powered monitoring, industrial control thresholds, sensor signal conditioning, window comparison, and four-channel level detection. The 14-SO package is suitable for conventional through-hole assembly and prototype boards. Because TS3704CD is obsolete, engineers should use a qualified drop-in option when possible or confirm lifecycle, availability, and qualification requirements for long-term production programs. For a new PCB, preserve the 14-pin SOIC footprint and verify every signal against the replacement part's pin description. Pay particular attention to input common-mode range, propagation delay, output polarity, supply voltage, and input bias current, since a matching package alone does not guarantee equivalent behavior in every operating condition. This page consolidates lifecycle information, verified distributor records, pin-compatible migration options, comparison parameters, and practical replacement guidance. The structured alternatives help engineers move away from the obsolete TS3704CD without relying on a mechanically similar but electrically unsuitable part.

RFQ İletişim
TS3704CN - Micropower Quad CMOS Comparator | STMicroelectronics
TS3704CN

TS3704CN - Micropower Quad CMOS Comparator | STMicroelectronics

The STMicroelectronics TS3704CN is a micropower quad CMOS voltage comparator with four independent comparison channels, push-pull outputs, and a low typical supply current of 9 µA per comparator. The device is packaged in a 14-pin DIP and is designed for low-power threshold detection, signal conditioning, and voltage-level comparison. A voltage comparator is an analog semiconductor that compares an input voltage with a reference or threshold and changes its output when the relationship between those voltages changes. The TS3704 belongs to the comparator hierarchy within integrated circuits and analog signal conditioning. Compared with the bipolar LM339 family, its CMOS implementation consumes substantially less current and uses push-pull outputs, eliminating the external pull-up resistor normally required by open-collector comparators. The principal features of the TS3704CN include four CMOS comparator channels, 9 µA typical current consumption per comparator, a fast response time of 2 µs typical for a 5 mV overdrive, and typical input impedance of 10^12 ohms. Its push-pull output stage can drive logic inputs directly while reducing external component count. The device is also described as pin-to-pin and functionally compatible with the bipolar LM339, although output polarity, common-mode limits, supply behavior, and timing should still be checked before substitution. The TS3704 architecture supports four independent threshold or window-detection functions in one package. High input impedance reduces loading on high-impedance sensor nodes, while the low 9 µA typical consumption per comparator suits battery-operated equipment. The 2 µs typical response is useful for systems requiring fast decisions without moving to a higher-power comparator family. Its through-hole DIP-14 construction also favors legacy industrial, instrumentation, and educational designs where socketed or leaded assembly is preferred. Typical uses include battery-powered sensor interfaces, overvoltage and undervoltage detection, industrial control thresholds, window comparators, and low-power monitoring systems. The TS3704CN is particularly appropriate when one board requires several independent comparisons and when avoiding open-collector pull-up components materially simplifies the design. Designers should account for input common-mode range, supply voltage, output drive, and input overvoltage before assigning comparator inputs. Because this is a leaded DIP device, board spacing, soldering heat, and cleaning practices also affect long-term assembly reliability. Decoupling should follow the manufacturer datasheet guidance, especially when long PCB traces or switching sources are present. This product record combines the manufacturer datasheet, distributor identification, explicit package information, cross-reference candidates, and practical engineering guidance to support component selection, replacement assessment, PCB planning, and low-power comparator design.

RFQ İletişim
TS3704ID - 4-Comparator 9uA CMOS IC | STMicroelectronics
TS3704ID

TS3704ID - 4-Comparator 9uA CMOS IC | STMicroelectronics

The STMicroelectronics TS3704ID is a micropower quad CMOS voltage comparator with four independent comparison channels, 9 uA typical supply current per comparator, push-pull CMOS outputs, and a 14-pin SOIC package. It compares two input voltages and produces a logic-level result indicating which input is higher, making it suitable for precision threshold detection and low-power signal conditioning. A voltage comparator is an analog interface component that translates a difference between two voltages into a digital logic state. Within the broader hierarchy of integrated circuits and interface ICs, the TS3704 combines four analog comparison functions with low-power digital output stages. Unlike the open-collector outputs used by many bipolar comparator families, its push-pull outputs source and sink current directly, eliminating the external pull-up resistor normally required. Key characteristics include 9 uA typical current consumption per comparator, 1 TΩ typical input impedance, and a 2 us typical response time for a 5 mV input step. The high input impedance minimizes loading on high-impedance sensors and divider networks. A push-pull output also provides faster signal transitions and makes the device suitable for systems that need a direct active-high or active-low logic indication without an added pull-up resistor. The TS3704 uses CMOS input and output circuitry to achieve low bias current and low power consumption while retaining the pin arrangement associated with the LM339 family. Its four channels share supply pins but operate independently, allowing one package to implement battery monitoring, supervision, window comparison, or several unrelated threshold functions. Maximum offset voltage, input common-mode limits, supply range, and output-drive details should be checked against the manufacturer datasheet for the specific operating conditions. Typical applications include low-voltage battery monitoring, industrial sensor thresholds, consumer power-fail detection, overvoltage and undervoltage supervision, and comparison of external reference voltages. In portable equipment, the low 9 uA typical consumption per channel helps limit standby drain, while the four-channel integration reduces package count and board area compared with discrete single comparators. Designers should account for input common-mode range, output levels, propagation delay, and unused-channel behavior before assigning every comparator. Inputs must remain within their specified operating range, and unused channels should be configured according to the manufacturer guidance rather than left floating. PCB placement should keep sensitive comparison nodes away from switching nodes and high-current return paths to minimize coupled errors. This page organizes the TS3704ID electrical characteristics, package and pin information, application guidance, lifecycle status, and confirmed drop-in alternatives into one design-focused reference. It also identifies where a direct substitution is not established, helping engineers distinguish a true same-footprint replacement from a merely similar quad comparator.

RFQ İletişim
TS3704IN - 4-Channel Micropower CMOS Comparator | STMicroelectronics
TS3704IN

TS3704IN - 4-Channel Micropower CMOS Comparator | STMicroelectronics

The STMicroelectronics TS3704IN is a micropower quad CMOS voltage comparator with four independent comparison channels, push-pull outputs, and a 14-pin PDIP package. Each comparator typically consumes 9 µA, while the complete device is designed for low-power signal conditioning. According to the manufacturer datasheet, the TS3704IN supports input voltages up to ±8 V with a nominal 16 V supply and accepts a single supply from 3 V. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its digital output state when one input exceeds the other. This places the TS3704IN within the hierarchy of comparator IC, analog interface IC, and semiconductor. Four independent channels in one package reduce board area in threshold detection, window comparison, sensor conditioning, and control systems where several voltage relationships must be monitored. Key features include a push-pull CMOS output stage that eliminates the external pull-up resistor required by open-collector comparators. The typical input offset voltage is 5 mV, typical input bias current is 600 pA, and the response time is approximately 2 µs for a 5 mV overdrive. A nominal supply voltage of 3 V and an operating temperature range from -40 °C to +125 °C support both portable and industrial designs. The CMOS input stage provides high input impedance, helping the TS3704IN interface with high-impedance sensors without drawing substantial signal current. Its four-channel architecture also simplifies power sequencing because all comparators operate from the same supply. The push-pull output can actively drive both high and low states, although designers must account for the output current and voltage limits specified by the manufacturer when connecting loads. Typical uses include battery-powered threshold detection, industrial sensor interfaces, window comparators, overvoltage monitoring, control-system logic, and four-channel signal conditioning. In portable equipment, the 9 µA typical consumption per comparator is especially useful. For longer trace runs or noisy industrial environments, input filtering and careful grounding remain necessary even though the push-pull output reduces dependence on external pull-up hardware. PCB layout should keep input and output traces short, provide a stable ground reference, and place input filtering close to the comparator inputs. Because all four channels share supply pins, bypassing the supply close to the package helps minimize disturbance between channels. Avoid relying on the comparator output for functions requiring a pull-up resistor, since the TS3704IN output architecture is push-pull rather than open collector. This product page combines the manufacturer’s electrical characteristics, package and pin information, verified distributor listings, application guidance, and a strictly same-package alternative assessment. It is intended to help engineers determine whether the TS3704IN’s four channels, low current consumption, input impedance, and output architecture fit a specific low-power design.

RFQ İletişim
TS372CD - Dual Precision CMOS Comparator | STMicroelectronics
TS372CD

TS372CD - Dual Precision CMOS Comparator | STMicroelectronics

STMicroelectronics TS372CD is a low-power dual precision CMOS voltage comparator containing two independent differential comparators, with a response time of 600 ns, a single-supply operating range of 1.5 V to 8 V, and an 8-pin SOIC package. Each comparator provides CMOS, MOS, or TTL-compatible open-drain output operation for interfacing with mixed logic systems. A voltage comparator is an analog signal-processing IC that compares an input voltage against a reference voltage and changes its output state when the differential input crosses the switching threshold. A dual comparator integrates two independent channels into one package. Within the broader semiconductor hierarchy, TS372CD belongs to the comparator and amplifier IC family, where it bridges low-power analog sensing and digital logic control. The TS372CD emphasizes low power and precision. The manufacturer specifies a very low supply current of 0.1 mA per comparator, independent of supply voltage. Its extremely low input bias current is typically 1 pA, and its input offset current is also typically 1 pA. These characteristics reduce disturbance from high-impedance sensors and make the device suitable for monitoring systems where the source impedance could otherwise create input-related errors. Its differential CMOS architecture supports single-supply or dual-supply operation. The wide single-supply range extends from 1.5 V to 8 V, while the dual-supply capability covers positive and negative sensing ranges. The open-drain outputs require an external pull-up resistor when the output must rise to a positive logic voltage. This configuration provides flexible bus-level interfacing and permits wired-AND behavior when multiple outputs share a pull-up node. Typical uses include battery-powered threshold detection, sensor signal conditioning, window monitoring, overvoltage and undervoltage detection, and low-speed control loops. The 600 ns response time is appropriate for power-management, industrial-control, and instrumentation systems that require a rapid decision without the higher energy consumption of a high-speed comparator. Design the pull-up network around the required logic level, output rise time, and total capacitance. Place the pull-up resistor close to the output net, keep comparator input traces away from switching nodes, and account for input bias current when driving very high source impedances. Verify startup behavior and logic thresholds across temperature when the comparator controls a safety-critical or precision system. This product page combines the TS372CD electrical characteristics, package details, verified drop-in replacement information, comparison parameters, and practical interface guidance. It helps engineers evaluate whether its low-power precision architecture fits a design before checking the manufacturer datasheet and confirming application-specific limits.

RFQ İletişim
TS372CN - Dual CMOS Comparator, 8-DIP | STMicroelectronics
TS372CN

TS372CN - Dual CMOS Comparator, 8-DIP | STMicroelectronics

The STMicroelectronics TS372CN is a low-power dual CMOS voltage comparator with two independent comparison channels, a 1.5 V to 8 V single-supply operating range, support for dual supplies up to ±8 V, and an 8-DIP package. It produces open-drain, TTL-compatible outputs and combines very low supply current with extremely low input bias current. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference crosses a reference level. Comparators belong to the broader interface and signal-conditioning hierarchy, where they convert physical voltage relationships into logic-level events. The TS372CN’s dual-channel architecture provides independent decisions within one package, reducing board area compared with two separate single comparators. Key characteristics include supply current of 0.1 mA per comparator independent of supply voltage, input bias current of 1 pA typical, and input offset current of 1 pA typical. The device operates from a 1.5 V to 8 V single supply or from dual supplies within the stated ±8 V limit. Its open-drain outputs can support TTL-compatible interfacing, while the low-power operation is useful when continuously powered sensing is required. The CMOS input stage is suited to monitoring high-impedance sources because the extremely low bias current minimizes loading of the measured node. Each comparator can evaluate an input against a reference voltage or against the other input when configured as a differential comparator. The manufacturer datasheet should be consulted for the complete electrical characteristics, input common-mode limits, output sink-current limits, and propagation-delay curves. Typical applications include battery-powered threshold detection, sensor-condition interfaces, window comparators, overvoltage and undervoltage indication, low-level signal crossings, and general dual-threshold logic. Two independent channels can also implement hysteresis, zero-cross detection, or a pair of complementary limit checks without requiring two separate IC packages. Designers should account for the open-drain output architecture by providing a pull-up resistor at every output used with subsequent digital logic. Input common-mode voltage, output timing, and supply bypass requirements must remain within the manufacturer’s specified operating limits. Decoupling capacitance should be placed close to the supply pins, while sensitive input traces should be kept short and away from switching nodes. This page organizes the key electrical characteristics, commercial information, package details, application guidance, and available cross-reference information for engineers evaluating the TS372CN. It also highlights where a substitution requires direct pin and parameter verification rather than relying on package similarity alone.

RFQ İletişim
TS372ID - Dual CMOS Voltage Comparator, 8-SOIC | STMicroelectronics
TS372ID

TS372ID - Dual CMOS Voltage Comparator, 8-SOIC | STMicroelectronics

The STMicroelectronics TS372ID is a low-power dual CMOS voltage comparator in an 8-pin SOIC package. It contains two independent precision differential comparators designed for single-supply operation from 3 V to 16 V or dual-supply operation from plus or minus 1.5 V to plus or minus 8 V. Each comparator offers an open-drain output suitable for TTL-compatible interfacing. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital logic state indicating which input is higher. The TS372ID belongs to the comparator category within analog and mixed-signal integrated circuits, where it is used for threshold detection, level sensing, signal conditioning, and simple control decisions. Its dual architecture allows two independent comparisons in one package, reducing component count when two threshold functions are required. The TS372ID uses STMicroelectronics silicon linMOS technology and emphasizes low power consumption. The manufacturer specifies a very low supply current of 0.1 mA per comparator, independent of supply voltage. Its extremely low input bias current is typically 1 pA, and its input offset current is also typically 1 pA, making the device suitable for high-impedance sensing circuits where source leakage could otherwise change the decision point. The wide operating-supply range allows the same device family to support low-voltage single-rail systems or balanced dual rails. Because the outputs are open-drain, each output requires an external pull-up resistor. This arrangement supports wired logic functions and allows the output transition speed to be adjusted through the pull-up resistance and circuit capacitance, but it also means an external pull-up is required to obtain a valid high output state. Typical uses include battery-powered threshold detection, sensor signal conditioning, overvoltage and undervoltage monitoring, window-comparison functions, and low-power control logic. When two comparators operate from the same supply, their individual input, output, and supply pins still require careful routing to avoid unintended coupling or output contention. For layout, place input and output traces away from high-current switching nodes and preserve a short return path to the supply ground. Select pull-up resistors according to the required rise time and available output current, and ensure that the input common-mode range remains within the limits stated in the manufacturer datasheet for the selected supply voltage. Decoupling capacitors should be placed close to the supply pins, with the ground connection kept short. This page organizes the TS372ID supply, input-current, package, output, and application information into an engineering-oriented selection guide. It also documents where to find the official datasheet, how to interpret the package and pinout, what to verify before making a replacement, and how to request a quotation through the XAIPART Request a Quote form.

RFQ İletişim
TS372IN - Dual CMOS Voltage Comparator, 8-DIP | STMicroelectronics
TS372IN

TS372IN - Dual CMOS Voltage Comparator, 8-DIP | STMicroelectronics

The STMicroelectronics TS372IN is a low-power dual CMOS voltage comparator containing two independent precision comparators, with a 600 ns response time and a maximum input offset voltage of 12 mV. Housed in an 8-pin through-hole DIP package, it accepts single supplies from 3 V to 16 V or dual supplies from ±1.5 V to ±8 V. Each comparator consumes approximately 0.1 mA, making the device suitable for low-power signal-conditioning systems. A voltage comparator is an analog mixed-signal semiconductor that compares two input voltages and produces a digital-level indication of their relationship. The TS372IN belongs to the comparator hierarchy and uses CMOS input stages with open-drain outputs, allowing its outputs to support TTL-compatible interfacing. Two independent comparator channels in one package reduce component count when a system needs two sensing or threshold decisions. Key features include independent comparator operation, low supply current of 0.1 mA per comparator, and operation from either a single or dual supply. The single-supply range of 3 V to 16 V supports industrial logic systems, while the ±1.5 V to ±8 V dual-supply range permits comparison of signals around ground. The open-drain output architecture also enables wired-AND behavior when multiple comparator outputs share a pull-up resistor. The differential CMOS architecture provides a favorable balance between speed, power consumption, and input behavior. With a response time of 600 ns, the TS372IN is suitable for threshold monitoring, signal crossing detection, and control-loop qualification without the delay of slower micropower comparators. Its two independent channels can monitor separate sensor nodes or provide complementary decisions, although common-mode range and input-bias details should be checked against the manufacturer datasheet for the exact operating conditions. Typical applications include industrial sensor thresholding, battery and power-supply monitoring, overvoltage detection, window comparison in control systems, and low-power logic interfaces. The device can also participate in line-driver or receiver designs where open-drain outputs are pulled up to a suitable logic supply. In dual-supply systems, it is useful when signals may fall below ground or rise above a midpoint reference. Design the input network so the differential signal remains within the comparator’s specified common-mode operating range, especially when operating from a 3 V single supply. Place the pull-up resistor directly at each open-drain output and confirm that its value produces the intended rise time. Do not permit an output to exceed its supply voltage, and use the DIP footprint without relying on exposed-pad thermal dissipation because the package does not provide one. This product page combines supply-range and timing details with package-level engineering guidance, application analysis, and qualified same-footprint replacement information. It is intended to help engineers select the TS372IN, plan the input and output network, and assess drop-in alternatives without confusing package compatibility with guaranteed functional equivalence.

RFQ İletişim
TS374CD - Low-Power Quad CMOS Comparator | STMicroelectronics
TS374CD

TS374CD - Low-Power Quad CMOS Comparator | STMicroelectronics

The STMicroelectronics TS374CD is a low-power quad differential CMOS voltage comparator containing four independent precision comparator channels in a 14-pin SOIC package. The device supports single- or dual-supply operation, provides open-drain outputs compatible with CMOS, MOS, and TTL logic, and combines a typical response time of 200 ns with very low power consumption. Its four-channel arrangement allows one package to implement four independent sensing or threshold functions. A voltage comparator is an analog semiconductor that compares two input voltages and changes its output state when the difference crosses a defined threshold. The TS374CD belongs to the comparator hierarchy within analog and interface ICs. Each channel has differential inputs, high input impedance, and an open-drain output that can pull a logic node low. When used with a pull-up resistor, the open-drain architecture supports wired logic, level translation, and direct interfacing with multiple open-drain devices. The principal device characteristics include four independent channels, a typical input impedance of 10^12 ohms, a typical input bias current of 1 pA at 5 V, and a maximum quiescent current of 250 microamperes. The fast typical response time of 200 ns is useful for signal crossing, threshold detection, and control-loop applications where the comparator must react quickly after an input differential changes polarity. Open-drain outputs provide flexible system integration without driving the output high actively. The TS374CD uses four independent precision voltage comparators implemented with STMicroelectronics silicon linear MOS technology. This process is intended to provide a favorable balance between consumption and operating speed. The very high input impedance reduces loading on the signals being measured, while the low typical bias current is beneficial when the comparator monitors high-impedance sensors or threshold networks. Because the output is open drain, its rising voltage is established by an external pull-up resistor rather than an internal active pull-up. Typical applications include sensor-threshold detection, overvoltage and undervoltage monitoring, window comparison, zero-cross detection, industrial control logic, and general-purpose analog signal conditioning. Four channels can also be used as independent comparator elements in a compact design, reducing package count compared with discrete or single-channel implementations. A pull-up resistor should be selected according to the target logic family, bus capacitance, and required rise time. When designing with the TS374CD, account for open-drain behavior and provide a suitable pull-up on every output used by downstream logic. Review input common-mode limits, supply range, output sink current, and propagation timing in the manufacturer datasheet before setting thresholds. Because this ordering code is listed as obsolete, confirm lifecycle status and obtain an approved replacement or a supported availability plan before beginning a new production design. This product page organizes the TS374CD’s comparator architecture, electrical characteristics, practical applications, verified equivalent information, and design considerations. It also highlights the lifecycle constraint and distinguishes a documented cross-brand alternative from components that may use the same 14-pin footprint but differ in output behavior, supply limits, or logic compatibility.

RFQ İletişim
TS374CN - Quad CMOS Comparator, 3-16 V, 14-DIP | STMicroelectronics
TS374CN

TS374CN - Quad CMOS Comparator, 3-16 V, 14-DIP | STMicroelectronics

The STMicroelectronics TS374CN is a low-power quad differential voltage comparator with four independent channels, open-drain outputs, and a 14-pin through-hole DIP package. It operates from 3 V to 16 V with a single supply or from ±1.5 V to ±8 V with dual supplies. Key characteristics include a typical response time of 200 ns, typical input impedance of 10^12 ohms, and very low input bias current of 1 pA at 5 V. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital logic result indicating which input is higher. Comparators belong to the broader interface IC and signal-conditioning hierarchy, where they convert continuously varying analog signals into logic-compatible decisions. The TS374CN's four independent channels make it useful wherever several threshold or sorting decisions must be performed by one device. The TS374CN provides four low-power precision comparators using a LinCMOS process. Its open-drain outputs allow the output node to be pulled up to a compatible supply through an external resistor, which supports wired-AND or wired-OR behavior when several outputs share a node. Typical input offset voltage is low, while the approximately 10^12-ohm typical input impedance minimizes loading on high-impedance sensor and divider networks. Operation from 3 V to 16 V makes the device suitable for 5 V logic systems and higher-voltage industrial interfaces. Maximum quiescent current is listed as 250 uA, reducing the impact of continuous comparator operation. The open-drain architecture can also support level translation when the pull-up supply differs from the comparator supply, provided voltage and timing limits are respected. Typical uses include sensor threshold detection, battery and power-supply monitoring, window comparators, overvoltage and undervoltage protection, signal crossing detection, and four-channel digital conditioning. The 200 ns typical response is suitable for many control and monitoring loops, although propagation-delay variation, input overdrive, and output pull-up resistance must be checked in fast systems. The principal design consideration is the open-drain output. Every used output requires an external pull-up resistor, and the resistor must satisfy the sink-current and rise-time requirements of the connected logic. Inputs should remain within the common-mode range, and unused comparator channels should be tied to defined logic levels rather than left floating. This page combines manufacturer-family characteristics, verified distributor packaging information, drop-in replacement guidance, comparison parameters, and practical circuit-design notes to support component selection and PCB implementation.

RFQ İletişim
TS374ID Low-Power Quad Comparator | STMicroelectronics
TS374ID

TS374ID Low-Power Quad Comparator | STMicroelectronics

The STMicroelectronics TS374ID is a low-power quad differential voltage comparator containing four independent comparison channels, a 3 V to 16 V supply range, open-drain outputs, and a 14-pin SOIC package. It provides a typical response time of 200 ns and a typical input impedance of 10^12 ohm, making it suitable for precision threshold, sensing, and signal-conditioning circuits. A voltage comparator is an analog signal-conditioning integrated circuit that compares two input voltages and changes its output state when the difference crosses a defined threshold. The TS374ID belongs to the comparator hierarchy, within analog ICs and signal-conditioning semiconductors. Its four channels can perform independent comparisons while sharing one supply and ground connection, reducing component count in multi-channel monitoring designs. Key characteristics include four independent differential comparators, low-power CMOS operation, low input offset voltage, a 3 V to 16 V operating range, and open-drain outputs. The open-drain architecture allows each output to be pulled up to the required logic level with an external resistor, which is useful when interfacing the TS374ID to systems operating above or below its supply voltage. The TS374ID uses STMicroelectronics silicon linear MOS technology to achieve its consumption-to-speed balance. Its typical 200 ns response time supports faster threshold decisions than general-purpose slow comparators, while the high typical input impedance reduces loading on the sensed source. Each differential input pair provides a non-inverting and an inverting comparison input, and the output indicates which input is higher. Typical uses include sensor threshold detection, battery and power-supply monitoring, industrial control logic, window comparators, overvoltage detection, and general digital control interfaces. The quad configuration is particularly useful when a board must monitor several independent analog quantities, such as temperature, pressure, current, or supply rails. Designers should use pull-up resistors on all open-drain outputs and confirm that output rise time, input common-mode range, and supply timing meet the system requirements. Care is also needed when several comparators can pull an output low simultaneously, because the shared pull-up resistor must tolerate the combined sink current. This page combines the TS374ID electrical characteristics, package details, practical circuit considerations, and package-compatible replacement guidance to support faster component selection, footprint verification, and second-source planning.

RFQ İletişim
TS374IDT - Low-Power Quad CMOS Comparator | STMicroelectronics
TS374IDT

TS374IDT - Low-Power Quad CMOS Comparator | STMicroelectronics

The STMicroelectronics TS374IDT is a low-power quad CMOS voltage comparator with four independent comparison channels, an open-drain output, and operation from a single 3 V to 16 V supply or from dual supplies of ±1.5 V to ±8 V. The device is packaged in a 14-pin SOIC and is intended for low-power voltage-sensing, threshold-detection, and signal-conditioning systems. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when their relationship crosses a defined threshold. The TS374 belongs to the comparator hierarchy within analog and interface semiconductors. Its four-channel architecture allows one package to monitor four independent signals, reducing board area when several sensing or control functions are required. The TS374IDT features very low supply current of approximately 0.1 mA per comparator, independent of supply voltage, and extremely low input bias and input offset currents of approximately 1 pA typical. The input offset voltage is specified to a maximum of 12 mV, while the response time reaches 600 ns. Its CMOS input stage supports operation from a single supply or from positive and negative dual supplies. Each channel uses open-drain output structure, allowing the output to be pulled up to a suitable external voltage and permitting wired connection to a shared bus when only one channel should actively assert a logic state. The open-drain architecture also provides flexibility when interfacing with CMOS, MOS, or TTL-compatible downstream circuitry. The manufacturer lists the TS374 family as a low-power quad CMOS voltage comparator supporting supply ranges from 3 V to 16 V or ±1.5 V to ±8 V. Typical uses include battery-powered threshold detection, industrial sensor interfaces, window or level monitoring, overvoltage detection, control systems, and general-purpose signal conditioning. The low input current is especially useful with high-impedance sensors because it minimizes loading of the measured signal. Designers should account for input common-mode limits, output pull-up requirements, input offset voltage, and the effect of supply noise on comparison accuracy. Every open-drain output needs an appropriate pull-up resistor unless it is intentionally connected to a shared wired-AND node. Decoupling close to the supply pins remains important even though the device itself consumes very little current. This product page combines manufacturer electrical characteristics, package details, sourcing information, and application guidance. It also highlights the design trade-offs involved when using a quad open-drain comparator instead of single-channel or push-pull alternatives, helping engineers select the correct replacement without changing the PCB footprint.

RFQ İletişim
TS374IN - Low-Power Quad CMOS Comparator | STMicroelectronics
TS374IN

TS374IN - Low-Power Quad CMOS Comparator | STMicroelectronics

STMicroelectronics TS374IN is a low-power quad CMOS voltage comparator containing four independent precision differential comparators, with a 200 ns typical response time, 10^12 ohm typical input impedance, and a 14-DIP package. The device accepts single- or dual-supply operation and provides open-drain, CMOS, MOS, or TTL-compatible output interfacing. A voltage comparator is an analog semiconductor that evaluates two input voltages and changes its output state when one input crosses the other. Quad comparators integrate four independent channels into one package, providing efficient threshold detection, window monitoring, and signal conditioning. Within the electronics hierarchy, the TS374IN belongs to the comparator family of analog and mixed-signal ICs, where precision voltage sensing interfaces with digital control systems. The TS374IN provides four independent precision channels in one 14-DIP package. Its input impedance of 10^12 ohms typical minimizes loading on high-impedance sensor and divider networks. A 200 ns typical response time supports faster decision-making in monitoring and control circuits, while the open-drain output architecture permits wired logic, pull-up integration, and multi-node signal combinations. The STMicroelectronics silicon lin MOS process gives the device its low-power operating characteristics and favorable consumption-speed ratio. Each comparator can operate from single or dual supplies, allowing the TS374IN to suit low-voltage logic systems as well as broader analog interfaces. Open-drain outputs support CMOS, MOS, and TTL-compatible downstream logic when suitable pull-up devices are used. Typical uses include four-channel threshold monitoring, sensor-signal conditioning, overvoltage detection, window comparators, industrial control interfaces, and general digital logic interfaces. The high input impedance is especially useful when the comparator must observe a high-impedance divider or sensor without materially affecting its operating point. The 14-DIP through-hole package also simplifies prototype construction and legacy PCB maintenance. When using open-drain outputs, include the appropriate pull-up resistor on each channel and account for its effect on rise time. Common-mode voltage limits, supply voltage, and output sink-current requirements must also be checked against the circuit operating conditions. The TS374IN datasheet pin description should be used directly when assigning PCB connections. This product data combines the STMicroelectronics family description with package, interface, and electrical characteristics, then adds application guidance, pin-use cautions, and a structured comparison framework to support practical design decisions.

RFQ İletişim
TS391ILT - Low-Power Single Comparator | STMicroelectronics
TS391ILT

TS391ILT - Low-Power Single Comparator | STMicroelectronics

The STMicroelectronics TS391ILT is a low-power, single voltage comparator with a supply range of 2 V to 34 V, a response time of approximately 0.3 µs to 1.3 µs depending on the operating condition, and an open-collector output. The device is packaged in a 5-pin SOT-23 surface-mount package for compact analog signal-conditioning and threshold-detection circuits. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital output indicating which input is higher. The TS391 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Its low-power design makes it useful where continuous monitoring is required, including industrial control, sensor interfaces, power-supply sequencing, battery monitoring, and portable equipment. Key characteristics include very low supply-current consumption, low input bias current, low input-offset voltage, and an input common-mode range extending close to both supply rails. Operation from a single supply is supported, and split-supply operation is also possible. The open-collector output requires an external pull-up resistor and can be connected to a compatible logic supply when the open-drain node must rise above the comparator supply voltage. The TS391/TS391A family uses an open-collector output architecture rather than a push-pull output. This allows the output to be pulled up to a selected logic voltage, supports wired-AND behavior with suitable arrangements, and provides a defined state when the output transistor is off. Input bias and offset characteristics determine the practical switching threshold accuracy, while propagation delay determines how quickly the circuit responds to an input crossing. Typical uses include monitoring sensor outputs, detecting overvoltage or undervoltage conditions, comparing temperature-derived analog signals, and providing a simple control decision in battery-powered products. The SOT-23-5 format supports dense PCB layouts, although engineers should account for the package's limited thermal dissipation and the output pull-up component required by the open-collector architecture. For reliable operation, use the pin-description table in the manufacturer datasheet when assigning PCB tracks because the comparator uses a specific five-terminal SOT-23 layout. Confirm input voltage, common-mode range, output pull-up voltage, and propagation-delay limits across the complete temperature range before committing the circuit to a safety- or timing-sensitive application. This product overview consolidates the comparator's electrical limits, package details, replacement constraints, and practical design guidance into one engineering reference. It also distinguishes true pin-compatible alternatives from functionally similar devices with different pin assignments, helping prevent PCB rework and unintended board-level failures.

RFQ İletişim
TS393CD - Dual Micropower Comparator | STMicroelectronics
TS393CD

TS393CD - Dual Micropower Comparator | STMicroelectronics

The STMicroelectronics TS393CD is a dual micropower CMOS voltage comparator with 9 µA typical supply current per comparator, a 2.5 µs typical response time, and an 8-pin SOIC package. Each channel provides an open-drain output, high input impedance, and compatibility with the electrical behavior of bipolar LM393-class comparators. A voltage comparator is an analog integrated circuit that evaluates two input voltages and changes its output state when their relationship crosses a defined threshold. The TS393 belongs to the comparator hierarchy, where it combines analog signal comparison with digital open-drain output signaling. Two independent channels in one package conserve board area in low-power sensing, monitoring, and control systems. The principal advantages are low power consumption, high input impedance, and a response time suited to general-purpose decision circuits. Each comparator consumes 9 µA typically, while the datasheet describes this as approximately 20 times lower consumption than a bipolar LM393. The open-drain outputs permit wired logic, wired-OR operation, and level translation when an external pull-up resistor is used. The 2.7 V to 16 V supply range supports low-voltage systems while retaining operating temperature coverage from -40 °C to 125 °C. The TS393CD uses CMOS input stages to achieve a typical input impedance of 10^12 ohms. This makes the device suitable for high-impedance sensors and divider networks because the input stage draws very little current. Its maximum input offset voltage of 6.5 mV defines the practical input-referred threshold uncertainty around the comparison point. Although the response time is not as short as that of a dedicated high-speed comparator, 2.5 µs is suitable for envelope detection, threshold supervision, and slow digital control loops. Typical uses include battery-powered sensor conditioning, window or level detection, overvoltage and undervoltage supervision, temperature threshold systems, and industrial control inputs. The two channels can monitor two independent quantities, or they can be used together when a more complex decision or hysteresis arrangement is required. Open-drain outputs are especially useful when multiple comparators must share a common bus. The principal design consideration is the open-drain output. Every output requires a pull-up resistor to the appropriate logic supply, and the selected resistor must satisfy the output's sink-current and rise-time requirements. The input common-mode range, output saturation levels, and pull-up voltage must also be checked against the circuit operating conditions before deployment. This product page combines manufacturer specifications, package and pin information, application guidance, and a focused replacement comparison. It highlights where the TS393CD differs from related open-drain comparator choices and explains the electrical checks required before approving a substitute in an existing PCB design.

RFQ İletişim
TS393CN - Micropower Dual CMOS Comparator | STMicroelectronics
TS393CN

TS393CN - Micropower Dual CMOS Comparator | STMicroelectronics

The STMicroelectronics TS393CN is a micropower dual CMOS voltage comparator featuring two independent comparison channels, open-drain outputs, and a typical supply current of 9 µA per comparator. It is packaged in an 8-pin DIP and is designed as a micropower alternative to the bipolar LM393. Its input impedance is typically 10^12 ohms, while its typical response time is 2.5 µs with 5 mV overdrive. These characteristics make the TS393CN suitable for low-power threshold detection, signal conditioning, and sensing circuits where dual-channel comparison is useful. A voltage comparator is a type of analog interface IC that compares two input voltages and produces a digital logic result indicating which input is higher. In this product hierarchy, the TS393CN is a dual-channel comparator, belonging to the broader comparator and analog interface IC families. Each channel can monitor a sensor, measurement node, or control threshold independently, allowing one package to perform two related comparison functions while consuming only 9 µA typically per channel. The TS393CN offers high input impedance of 10^12 ohms typically, minimizing loading on the circuit being measured. Its 2.5 µs typical response time for 5 mV overdrive provides useful speed for threshold-control applications while retaining the low current consumption associated with CMOS design. Open-drain outputs also support wired-AND, wired-OR, and level-shifting arrangements when suitable pull-up resistors are added. The manufacturer identifies the device as pin-to-pin and functionally compatible with the bipolar LM393. Because both channels are implemented in CMOS, the TS393CN avoids the comparatively high quiescent current of conventional bipolar LM393 implementations. The manufacturer describes its typical consumption as 20 times lower than the bipolar LM393 while retaining similar performance. This makes it particularly attractive in battery-operated equipment where the comparator can remain active continuously without imposing the same continuous bias-current burden as a bipolar counterpart. Typical uses include battery threshold monitoring, window-comparison systems, temperature-limit detection, low-voltage signaling, and general-purpose sensing interfaces. The two independent channels can compare two sensed quantities against separate references or implement complementary threshold decisions. Its 8-pin DIP format also supports through-hole prototyping, educational equipment, repair work, and industrial control assemblies where socketed or leaded components are preferred. Designers should account for the open-drain output architecture by placing a pull-up resistor on each output. Input common-mode range, supply-voltage limits, output sink current, and operating temperature boundaries must be checked against the manufacturer datasheet before final circuit release. The DIP package also requires adequate lead spacing and mechanical clearance from nearby conductors, especially in high-voltage or densely populated assemblies. This page combines the core electrical characteristics of the TS393CN with package information, practical comparator design guidance, and a focused comparison with documented LM393-compatible devices. It is intended to help engineers identify where the micropower CMOS implementation offers a practical advantage without overlooking the open-drain pull-up requirements and application-specific limits of the original design.

RFQ İletişim
TS393ID - Dual Micropower CMOS Comparator | STMicroelectronics
TS393ID

TS393ID - Dual Micropower CMOS Comparator | STMicroelectronics

STMicroelectronics TS393ID is a micropower dual CMOS voltage comparator with an operating supply range of 2.7 V to 16 V, typical consumption of 9 µA per comparator, and open-drain outputs in an 8-pin SOIC package. The device contains two independent comparison channels, making it suitable for dual-threshold, window-monitoring, sensing, and low-power signal-conditioning circuits. Its typical supply current is stated as approximately 20 times lower than that of the bipolar LM393, while retaining the familiar open-drain output architecture. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their relationship. The TS393ID belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Its CMOS implementation emphasizes low supply current, and its open-drain outputs allow multiple devices to share a common pull-up when wired-AND behavior is required. These characteristics place it between simple threshold logic and more complex analog front ends. The primary features include two independent CMOS comparators, a 2.7 V to 16 V supply range, and 9 µA typical current consumption per comparator. Each output is open drain and requires an external pull-up resistor when a logic-high output is required. The SOIC-8 package provides a conventional surface-mount footprint suitable for compact industrial, consumer, instrumentation, and embedded-control designs. The manufacturer also identifies the TS3702 as a related dual micropower comparator offering similar performance with push-pull CMOS outputs. Electrically, the open-drain stage can pull its output low but cannot actively drive a high level. This gives designers control over rise time through the pull-up resistor and allows several comparator outputs to share a bus. That flexibility is useful in battery-powered equipment where minimizing activity is important, although the external pull-up contributes its own continuous current after an output is released. The two channels can compare different signal pairs or operate together for window supervision. Typical applications include battery-powered threshold detection, sensor signal conditioning, overvoltage and undervoltage indication, temperature-alarm circuits, industrial control interfaces, and low-power monitoring modules. The comparator may be used with op-amp-like input networks, dividers, current sensors, or digital control inputs where the required decision is binary. Because output polarity and timing determine system behavior, both input and output details should be checked against the manufacturer datasheet before final circuit release. A key design consideration is the external pull-up on each open-drain output. Select its resistance to balance noise immunity, switching speed, and power consumption, then confirm that every connected output can safely share the same node. Account for input common-mode limits, supply decoupling, output rise time, and any required hysteresis. The two channels are independent, so grounding or signal-conditioning requirements should be evaluated separately for each comparator. This page combines the TS393ID's verified electrical and packaging characteristics with drop-in candidate evaluation, parameter-by-parameter comparison, sourcing guidance, and practical circuit-design notes. It is intended to accelerate component selection while preserving the need to confirm detailed operating limits and timing behavior against the manufacturer datasheet.

RFQ İletişim