Entegre Devreler

A3P015-QNG68

A3P015-QNG68 - 15K-Gate 231MHz FPGA | Microchip

Microchip Technology A3P015-QNG68 is a 15,000-gate ProASIC3 flash FPGA with 49 user I/O pins, a 231 MHz maximum device speed, and 130 nm process technology. It operates from a 1.425 V to 1.575 V core supply and is packaged in a 68-pin VFQFN with an exposed pad for surface-mount assembly. The combination of 15K gates, 49 user I/O, and a compact 68-pin package makes the device suitable for compact control, interface, glue-logic, and embedded signal-processing systems. A field-programmable gate array, or FPGA, is a reconfigurable digital semiconductor whose logic and interconnect paths are programmed after manufacture. FPGAs sit between fixed-function application-specific integrated circuits and microcontrollers: they provide parallel hardware logic, deterministic timing, and flexible in-system configuration without requiring a custom mask set. The ProASIC3 family combines flash-based nonvolatile configuration with programmable logic resources for moderate-complexity embedded applications. The A3P015-QNG68 provides 15,000 logic gates, 49 user I/O, and a listed operating frequency of 231 MHz. Its 1.5 V core operating range of 1.425 V to 1.575 V supports low-voltage digital power architecture. Flash configuration retains the programmed design when power is removed, avoiding configuration reload from an external memory after each power cycle. The exposed pad also provides a direct thermal path from the FPGA to the PCB copper when the assembly uses an appropriate land pattern. The 68-VFQFN exposed-pad package reduces board area compared with larger leaded FPGA packages, but its fine pitch and exposed thermal pad require careful PCB layout. Short supply connections, a continuous ground reference, and low-impedance decoupling are particularly important because the device combines configurable logic with a high-I/O-count package. Designers should use the package drawing and pin-description table in the manufacturer datasheet when defining the footprint and routing board layers. Typical uses include industrial control interfaces, communications adapters, instrumentation, embedded protocol bridges, sensor conditioning, and compact test equipment. It is also appropriate when a design needs more parallelism or deterministic hardware behavior than a microcontroller provides, but does not justify the power, cost, and software complexity of a larger FPGA. The main design trade-off is capacity rather than package compatibility. The 15,000-gate device is best for compact logic blocks and peripheral integration; designs approaching the resource limit should account for routing overhead and reserve logic for timing, control, and system functions. Validate every pin assignment and I/O standard against the manufacturer pin-description table before release. This page combines the exact A3P015-QNG68 specifications, verified package information, source-backed alternatives, application guidance, and PCB-focused design notes to support engineering selection and footprint verification.

RFQ İletişim

A3P030-2QNG48

A3P030-2QNG48 - ProASIC3 FPGA 30K Gates | Microchip Technology

The Microchip Technology A3P030-2QNG48 is a ProASIC3 Field Programmable Gate Array (FPGA) with 30,000 system gates, 768 logic modules, and 34 user I/Os, housed in a 48-pin VQFN (QNG) package with exposed pad. It operates at a maximum internal frequency of 310 MHz and is fabricated on 130nm flash-based CMOS technology, requiring a 1.5V core supply. A Field Programmable Gate Array (FPGA) is an integrated circuit that can be configured by the customer after manufacturing to implement any digital logic function. Unlike fixed-function ASICs, FPGAs contain an array of programmable logic blocks and interconnects that can be reprogrammed to implement complex digital systems. The ProASIC3 family is a flash-based FPGA, meaning configuration is stored in non-volatile flash memory, allowing instant-on operation and secure design protection without external boot memory. Key features of the A3P030-2QNG48 include 30K system gates, 768 logic modules (equivalent to 330 logic elements), 34 user I/Os, and support for multiple I/O standards including LVCMOS, LVTTL, and PCI. The device offers 1Kbits of FlashROM for non-volatile data storage and is reprogrammable, enabling design updates in the field. The 48-pin VQFN package measures 6x6 mm with a 0.4 mm pitch, providing a compact solution for space-constrained applications. The ProASIC3 architecture uses a flash-based switch fabric that eliminates the need for external configuration PROMs, reducing system cost and board space. The device supports partial reconfiguration and has built-in security features including AES-128 bitstream encryption and a device lock to prevent reverse engineering. The 130nm process technology balances performance with low power consumption, making it suitable for battery-powered and thermally constrained designs. Typical applications for the A3P030-2QNG48 include industrial control, communications interfaces, motor control, and sensor signal processing. Its low density and small footprint make it ideal for glue logic, bus bridging, and state machine implementations where a full-size FPGA would be overkill. The 34 I/Os can interface with various peripherals and memory devices, providing flexible system integration. When designing with this device, ensure proper decoupling of the 1.5V core supply and 2.5V/3.3V I/O supplies. The exposed pad must be soldered to the PCB ground plane for thermal management and electrical grounding. The device supports JTAG programming and in-system programming via the SPI interface, simplifying manufacturing and field updates. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers with a comprehensive resource for evaluating the A3P030-2QNG48 in their designs.

RFQ İletişim

A3P030-2QNG48I

A3P030-2QNG48I - ProASIC3 Flash FPGA 30K Gates | Microchip

The Microchip Technology (Microsemi) A3P030-2QNG48I is a flash-based ProASIC3 FPGA offering 30K system gates, 330 logic elements (VersaTiles), and 34 user I/Os in a 48-pin VFQFN exposed-pad (QNG48) package, rated for industrial temperatures of -40C to +85C with speed grade 2. A flash-based FPGA is a field-programmable gate array whose configuration is stored in on-chip non-volatile flash memory rather than an external configuration ROM. Within the programmable logic hierarchy, the A3P030 sits at the low end of the FPGA family tree, below mid-density and high-density FPGAs and far above simple CPLDs, making it a single-chip, low-cost programmable solution for glue logic, control, and interface bridging tasks. Key features include instant-on, live-at-power-up operation because the flash fabric is inherently non-volatile, eliminating the external boot device required by SRAM FPGAs. The 1.5V core with 130nm flash process delivers up to 310 MHz internal system performance, while the small 7x7 mm QFN footprint suits space-constrained boards. Security features protect the design from readback, and full reprogrammability supports in-field updates. The ProASIC3 architecture uses a Sea-of-Tiles fabric of VersaTiles, each configurable as logic, arithmetic, or memory elements, connected through a hierarchical routing structure. Embedded flash and optional soft ARM support extend capability beyond pure glue logic. I/O banks support popular single-ended standards, and the fabric is qualified across industrial temperature ranges. Typical applications include portable and handheld instrument control logic, industrial automation interface bridging, power-on sequencing and system supervision, and replacement of multiple discrete ASSP or CPLD devices in cost-sensitive designs where a single-chip flash FPGA reduces total cost of ownership. Design consideration: plan 1.5V core supply sequencing and adequate QFN thermal/electrical grounding through the exposed pad, and verify I/O bank voltage assignment in Libero SoC before board layout. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet, with pricing referenced as of 2026-08-31.

RFQ İletişim

A3P030-2QNG68

A3P030-2QNG68 - ProASIC3 FPGA 30K Gates 68-QFN | Microchip

The Microchip (Microsemi/Actel) A3P030-2QNG68 is a ProASIC3 flash-based FPGA with 30K system gates, 310 MHz system performance, 49 user I/O, and 1.5V core operation, housed in a 68-pin VFQFN exposed-pad package. The -2 speed grade and flash programming fabric make it a single-chip, non-volatile solution for low-density logic integration. A flash-based FPGA is a field-programmable gate array whose configuration is stored in on-chip flash cells rather than an external configuration device. Within the programmable logic hierarchy, the ProASIC3 family sits under Microchip's low-density, non-volatile FPGA portfolio, positioning it above CPLDs in gate capacity while avoiding the configuration PROM required by SRAM FPGAs. Key features include 30,000 system gates (330 logic elements per distributor listings), 310 MHz maximum system performance in the -2 speed grade, single 1.5V core supply, and instant-on operation because configuration data resides in on-chip flash. The 68-VFQFN exposed-pad package (7x7 mm class) provides a small footprint with thermal dissipation through the pad, and 49 user I/O support both 3.3V and lower-voltage I/O banks for mixed-voltage board designs. Technologically, ProASIC3 uses a 130nm flash process with fine-grained VersTile logic architecture. Because the fabric is live at power-up, designs requiring immediate control-plane or glue-logic function do not need a host microcontroller to load bitstreams, improving system reliability and boot behavior versus SRAM-based FPGAs. Reprogrammability in-system supports field updates without changing hardware. Typical applications include industrial control and automation glue logic, portable and space-constrained consumer designs, power sequencing and reset management, bridge and interface conversion, and secure single-chip designs where bitstream external storage is undesirable. Design considerations: the 1.5V core rail must be sequenced and decoupled per the manufacturer datasheet, and the exposed pad must be soldered to a grounded thermal land for reliable operation. Verify I/O bank voltage assignments before layout because QFN pinout is fixed. This page synthesizes distributor pricing, drop-in alternatives, engineering design notes, and sourcing data not found in the manufacturer datasheet.

RFQ İletişim

A3P030-2QNG68I

A3P030-2QNG68I - ProASIC3 Flash FPGA 30K Gates | Microchip

The Microchip (Actel/Microsemi) A3P030-2QNG68I is a ProASIC3 flash-based FPGA delivering 30,000 system gates, 49 user I/Os, and up to 310 MHz system performance in a 68-pin VFQFN exposed-pad package operating from a 1.5V core supply. Manufactured on a 130nm flash process, it is an industrial-temperature (I suffix) grade-2 speed device. A flash-based FPGA is a type of field-programmable gate array that stores its configuration in on-chip flash memory cells rather than volatile SRAM. This places the ProASIC3 family in the broader hierarchy of programmable logic: FPGA -> programmable logic device -> digital IC -> semiconductor. Because configuration is non-volatile, the device powers up instantly without an external configuration PROM or boot controller, making it a single-chip solution for space-constrained systems. Key features include 330 logic elements (LEs), flash-based LiveField reprogrammability, single-supply 1.5V core operation, small-footprint VFQFN packaging, and optional soft ARM support as noted in the ProASIC3 family datasheet. The ultra-low-density class of the device targets glue logic, control-plane functions, and power-up sequencing tasks that previously used CPLDs or discrete logic. Technically, the A3P030 uses Actel's proprietary flash switch technology, which combines the non-volatility of antifuse devices with the reprogrammability of SRAM FPGAs. The 130nm process yields low static power, and the exposed-pad QFN provides good thermal and ground performance for a small 8x8 mm-class footprint. Typical applications include industrial automation control, portable and battery-powered instruments, bridge logic between processors and peripherals, power sequencing controllers, and secure single-chip logic where bitstream volatility would be a liability. A key design consideration is I/O budget: with only 49 user I/Os available in the 68-pin package, pin mapping should be validated early in Libero SoC before routing commitment. This page synthesizes distributor availability, drop-in family alternatives, and practical design notes not consolidated in the manufacturer datasheet.

RFQ İletişim

A3P030-2VQG100I

A3P030-2VQG100I - ProASIC3 FPGA, 30K Gates | Microchip

The Microchip Technology A3P030-2VQG100I is a low-density flash-based FPGA from the ProASIC3 family, offering 30,000 system gates, 330 logic elements, and 77 user I/Os in a 100-pin VQFP package. It operates from a 1.5V core supply and supports system performance up to 310 MHz, making it a single-chip, reprogrammable solution for cost-sensitive applications. A Field Programmable Gate Array (FPGA) is an integrated circuit that can be configured by the customer after manufacturing to implement arbitrary digital logic functions. Unlike fixed-function ASICs, FPGAs contain programmable logic blocks and interconnects that can be reconfigured to implement complex digital systems. The ProASIC3 family uses flash-based configuration, which retains the design even when power is removed, providing instant-on capability and inherent security against reverse engineering. Key features of the A3P030-2VQG100I include 30K system gates, 330 logic elements, 77 user I/Os, and a 1.5V core voltage. The device supports up to 310 MHz system performance and is offered in a 100-pin VQFP package with 0.5mm pitch. It is lead-free and RoHS compliant, with an operating temperature range of -40°C to +85°C, making it suitable for industrial environments. The ProASIC3 architecture is based on a flash-based switch fabric that provides non-volatile, low-power operation. Unlike SRAM-based FPGAs, it does not require an external configuration device, reducing system cost and board space. The device also includes advanced features such as clock conditioning, PLLs, and support for multiple I/O standards, enabling flexible system integration. Typical applications include industrial control, automotive electronics, communications infrastructure, and consumer electronics. The low density and small footprint make it ideal for glue logic, bus interfacing, and control applications where a full-sized FPGA would be overkill. The 77 I/Os provide ample connectivity for peripheral interfaces. When designing with this device, ensure proper decoupling of the 1.5V core supply and follow the recommended power-up sequencing. The flash-based configuration eliminates the need for external boot memory, simplifying the design and reducing BOM cost. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers with a comprehensive resource for evaluating the A3P030-2VQG100I.

RFQ İletişim

A3P030-QNG48

A3P030-QNG48 - 30K Gate ProASIC3 FPGA | Microchip Technology

The Microchip Technology A3P030-QNG48 is a ProASIC3 field-programmable gate array with 30,000 logic gates, 34 user I/O, a 231 MHz operating frequency, and a 48-pin QFN exposed-pad package. It uses 130 nm CMOS technology and operates from a 1.5 V core supply, making it a compact programmable-logic option for embedded control, interface, and signal-processing designs. An FPGA is a programmable digital semiconductor whose interconnected logic, memory, and I/O blocks are configured after manufacture. In the broader device hierarchy, a ProASIC3 FPGA belongs to the field-programmable logic and semiconductor categories. Unlike a fixed-function microcontroller, an FPGA implements parallel digital logic and control functions directly in hardware, allowing design changes without replacing the packaged device. The A3P030 family provides a compact solution for low-to-medium gate-count designs, small-footprint packages, and reprogrammable systems. Its headline specifications are 30,000 gates, 34 I/O, and 231 MHz performance. The 1.5 V operating supply reduces the core voltage requirement, while the exposed pad supports heat transfer from the device into the PCB copper during operation. The part belongs to the ProASIC3 family and uses 130 nm CMOS fabrication. This combination places it in a compact, nonvolatile FPGA category intended for applications where reprogrammability, small size, and system integration matter more than very high logic density. The package designation QNG48 identifies the 48-pin QFN form used by the listed A3P030 configuration. Typical uses include industrial control logic, sensor and signal conditioning, low-complexity data acquisition, communications interface adaptation, and embedded control subsystems. The 34 available I/O support connections to sensors, converters, memories, communication devices, and discrete logic while the FPGA fabric performs parallel processing or state-machine control. PCB implementation requires careful connection of the exposed thermal pad, supply decoupling, and all 34 I/O signals. Confirm the exact pin names and configuration requirements in the manufacturer datasheet before assigning tracks, and provide adequate ground-plane area beneath the package to support electrical return paths and heat removal. This page combines manufacturer-family information, package details, verified ordering data, compatible family members, and practical implementation guidance. It also distinguishes documented same-footprint alternatives from broader functional choices so engineers can assess PCB reuse, logic capacity, speed grade, and environmental requirements before committing a design to production.

RFQ İletişim

A3P030-QNG48I

A3P030-QNG48I - 30K Gate ProASIC3 FPGA | Microchip

The Microchip A3P030-QNG48I is a low-density, flash-based FPGA from the ProASIC3 family, offering 30,000 system gates and 34 user I/Os in a 48-pin QFN package. It operates over the industrial temperature range of -40°C to +100°C and supports core voltages of 1.5V, making it suitable for a wide range of embedded applications. An FPGA (Field-Programmable Gate Array) is an integrated circuit that can be configured by the customer after manufacturing to implement custom digital logic functions. Unlike fixed-function ASICs, FPGAs offer reprogrammability, allowing designers to iterate on designs without costly mask changes. The ProASIC3 family is known for its flash-based configuration, which provides instant-on capability, low power consumption, and high security against reverse engineering. Key features of the A3P030-QNG48I include 30,000 system gates, 34 user I/Os, and support for multiple I/O standards including LVCMOS, LVTTL, and PCI. It also features 1 kbit of FlashROM for non-volatile storage, an on-chip PLL for clock management, and a JTAG interface for programming and boundary-scan testing. The device is RoHS compliant and lead-free, meeting modern environmental standards. Technically, the ProASIC3 architecture uses a flash-based switch matrix that retains configuration data even when power is removed, eliminating the need for external configuration memory. This results in a single-chip solution with instant-on operation and enhanced security. The device also includes an internal charge pump to support programming, and its low power consumption makes it ideal for battery-powered applications. Typical applications include industrial control systems, automotive electronics, consumer devices, and communication interfaces. The A3P030-QNG48I is particularly suited for glue logic, bus interfacing, and custom peripheral expansion in space-constrained designs. When designing with this FPGA, ensure proper decoupling of the core and I/O power supplies, and follow the recommended programming and configuration guidelines in the datasheet. The device supports in-system programming via JTAG, simplifying firmware updates in the field. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing a comprehensive resource for engineers evaluating the A3P030-QNG48I.

RFQ İletişim

A3P030-QNG68

A3P030-QNG68 - 30K Gate 231MHz ProASIC3 FPGA | Microchip

The Microchip Technology A3P030-QNG68 is a ProASIC3 ultra-low-density FPGA with 30,000 logic gates, a maximum operating frequency of 231 MHz, and 49 I/Os in a 68-pin VFQFN package with an exposed pad. The device uses 130 nm CMOS technology and is identified as a 1.5 V FPGA. Its compact package and reprogrammable architecture suit embedded control, interface bridging, and low-complexity programmable logic designs. A field-programmable gate array is a semiconductor device whose digital logic functions are configured after fabrication. An FPGA belongs to the programmable-logic hierarchy, which also includes complex programmable logic devices and programmable system-on-chip devices. Compared with a fixed-function application-specific integrated circuit, an FPGA allows logic behavior, timing, and I/O assignments to be revised without replacing the physical device. The A3P030 device family is positioned for designs requiring a small amount of programmable logic without the resource level of a larger FPGA. The A3P030-QNG68 provides 30K logic gates, 49 I/Os, and operation up to 231 MHz. Its 68-pin exposed-pad package supports compact surface-mount layouts, while the exposed pad provides a defined thermal and electrical connection to the board. ProASIC3 devices combine configurable logic with programmable I/O and are intended for embedded applications where a controller, state machine, communication interface, or hardware accelerator must be adapted after board design begins. The 130 nm CMOS process is a key implementation detail for understanding the device's logic density, power characteristics, and timing performance. The A3P030-QNG68 is the commercial A3P030 ordering variant used in the 68-pin VFQFN exposed-pad configuration. Typical applications include industrial control, sensor aggregation, serial-interface conversion, data acquisition, communication routing, embedded security, and general-purpose logic prototyping. The 49 available I/Os make the device especially useful for designs that need multiple digital connections while remaining within an ultra-low-density FPGA footprint. When assigning a PCB layout, reserve the exposed pad according to the manufacturer's package drawing and connect it to the intended power or ground plane. Confirm signal integrity, I/O standards, supported clock conditions, and configuration requirements in the A3P030 datasheet before releasing a production board. This product page combines the exact A3P030-QNG68 identification, ProASIC3 family characteristics, package details, sourcing guidance, related ordering variants, and engineering-oriented design notes. It helps engineers distinguish the device from larger ProASIC3 members, identify the correct package and performance class, and plan a practical drop-in review before PCB commitment.

RFQ İletişim

A3P030-VQ100

A3P030-VQ100 - 330 Logic Cells ProASIC3 FPGA | Microchip

The Microchip Technology A3P030-VQ100 is a ProASIC3 field-programmable gate array with 330 logic elements, 77 I/O, and a 100-pin TQFP package. It belongs to the ProASIC3 family of reprogrammable semiconductor devices designed for compact embedded control, interface, and signal-processing systems. The device combines programmable logic with a small-package configuration suitable for space-constrained industrial and commercial equipment. A field-programmable gate array, or FPGA, is a semiconductor whose digital logic is configured after manufacture. Within the broader integrated-circuit hierarchy, an FPGA belongs to programmable logic devices and can implement state machines, control logic, protocol interfaces, and data-processing functions in parallel. Unlike a fixed-function application-specific integrated circuit, an FPGA permits design revisions, field upgrades, and adaptation to multiple product variants without changing the physical PCB layout. The A3P030-VQ100 provides 330 logic elements and 77 I/O in its 100-lead TQFP package. Its key advantage is integration: multiple digital functions can be placed in one programmable device, reducing component count and allowing design changes to be made through configuration rather than a physical respin. ProASIC3 devices also support flash-based configuration, making them suitable for systems that require reliable nonvolatile storage of the programmed configuration. The 100-pin TQFP package provides a practical interface count for boards that need moderate parallel I/O while retaining through-hole lead visibility and conventional assembly handling. The A3P030 is positioned as an ultra-low-density ProASIC3 option, making it appropriate for embedded control logic, peripheral bridges, instrumentation interfaces, and compact industrial controllers. Designers should evaluate the final design against the family’s exact electrical, timing, and configuration specifications before committing to a production board. Typical applications include sensor aggregation, motor and sequencing control, industrial communication interfaces, test equipment, embedded data-acquisition control, and low-cost programmable logic. Its 330 logic elements make it especially suitable for designs where logic complexity is moderate rather than requiring a high-density FPGA. Multiple I/O allow external memories, converters, communications transceivers, and discrete sensors to connect without requiring a separate large package. A key design consideration is PCB planning. Although the TQFP outline is conventional, pin assignments, configuration requirements, supply requirements, decoupling, and programming connections must follow the manufacturer’s device guidance. Confirm that the selected ProASIC3 density has sufficient logic, memory, and I/O resources, and verify the exact suffix and temperature grade before releasing production files. This product page consolidates the confirmed device identity, package, logic-resource count, I/O count, lifecycle considerations, and migration options into an engineering-focused guide. It also identifies the differences that must be checked between package-compatible variants, helping designers distinguish a true board-level replacement from a merely similar ProASIC3 device.

RFQ İletişim

A3P060-1FG144T

A3P060-1FG144T - ProASIC3 FPGA, 60K Gates | Microchip

The Microchip Technology A3P060-1FG144T is a flash-based FPGA from the ProASIC3 family, offering 60,000 system gates, 272 MHz maximum internal frequency, and 1.5 V core voltage, housed in a 144-pin FBGA package. It is designed for automotive applications, supporting junction temperatures up to 135°C and providing a single-chip, reprogrammable solution with low total cost of ownership. An FPGA (Field-Programmable Gate Array) is an integrated circuit that can be configured by the customer after manufacturing to implement custom digital logic functions. Unlike ASICs, FPGAs are reprogrammable, allowing design changes without costly mask revisions. The ProASIC3 family uses flash-based configuration, which retains the program even when power is removed, offering instant-on operation and enhanced security compared to SRAM-based FPGAs. Key features include 60K system gates, 272 MHz system performance, 1.5 V core voltage support for 1.5-V-only systems, low-impedance flash switches, and segmented hierarchical routing. The device also features high-performance, low-skew global networks, and is available in automotive grade with PPAP documentation. Its flash-based architecture provides inherent security against reverse engineering and supports live updates. The A3P060-1FG144T is built on 130 nm flash technology, offering a balance of low power consumption and high performance. The 144-pin FBGA package provides a compact footprint suitable for space-constrained automotive electronics. The device supports multiple I/O standards and includes programmable I/O with various drive strengths and slew rates. Typical applications include automotive body electronics, motor control, infotainment systems, and industrial automation. Its automotive qualification and wide temperature range make it ideal for under-hood and in-cabin electronics where reliability is critical. The flash-based configuration allows for secure remote updates and reduces system cost by eliminating external configuration memory. When designing with this device, ensure proper power supply decoupling with 0.1 uF and 10 uF capacitors near the VCC and GND pins. The core voltage must be maintained at 1.5 V ±5% for reliable operation. Use the JTAG interface for programming and configuration, and follow the recommended PCB layout guidelines in the datasheet for optimal signal integrity. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers with a comprehensive resource for evaluating the A3P060-1FG144T in their designs.

RFQ İletişim

A3P060-1VQ100T

A3P060-1VQ100T - 60K Gate ProASIC3 FPGA | Microchip Technology

The Microchip Technology A3P060-1VQ100T is a 60,000-gate ProASIC3 Field Programmable Gate Array (FPGA) with 71 programmable I/O pins and 18,432 bits of RAM, housed in a 100-pin VQFP (14x14 mm) package. It operates from a 1.5V core supply (1.425V to 1.575V) and supports an extended temperature range of -40°C to 125°C (TA). This device is AEC-Q100 qualified, making it suitable for automotive and other high-reliability applications. A Field Programmable Gate Array (FPGA) is an integrated circuit that can be configured by the customer after manufacturing to implement custom digital logic functions. FPGAs belong to the programmable logic device (PLD) family, which sits between fixed-function ASICs and general-purpose processors in the digital logic hierarchy. The ProASIC3 family uses flash-based configuration, offering non-volatile, single-chip operation with instant-on capability and inherent security against reverse engineering. Key features of the A3P060-1VQ100T include 60,000 system gates, 71 user I/Os, 18,432 bits of RAM, and a system performance of up to 272 MHz. The flash-based architecture provides low power consumption, high reliability, and immunity to configuration loss. The device supports multiple I/O standards, including LVCMOS, LVTTL, and PCI, and includes phase-locked loops (PLLs) for clock management. Technically, the ProASIC3 family is fabricated using a 130nm flash process, which enables non-volatile configuration without external boot memory. This reduces system cost and board space while improving security. The device features 1,536 logic modules (tiles) and supports up to 272 MHz system performance. The 100-pin VQFP package offers a compact footprint with a 0.5mm pitch, suitable for space-constrained designs. Typical applications include automotive electronics (e.g., motor control, sensor interfacing), industrial automation, communications infrastructure, and consumer electronics. The AEC-Q100 qualification and extended temperature range make it ideal for under-hood automotive modules and industrial control systems where reliability is critical. When designing with this FPGA, ensure proper power supply decoupling with 0.1uF and 10uF capacitors close to the VCC and GND pins. The flash-based configuration requires no external configuration device, simplifying PCB layout. For JTAG programming, follow the recommended programming header connections in the datasheet. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers with a comprehensive resource for component selection and design.

RFQ İletişim

A3P060-1VQG100T

A3P060-1VQG100T - ProASIC3 Flash FPGA 60k Gates | Microchip

The Microchip (formerly Microsemi/Microchip USA lineage) A3P060-1VQG100T is a ProASIC3 flash-based FPGA with 60,000 system gates, 1,536 logic cells (VersTiles), up to 71 user I/O, and a maximum internal frequency of 350 MHz, housed in a 100-pin VQFP/TQFP package with 0.5 mm pitch. The -1 suffix denotes the standard speed grade, and the T suffix denotes tape-and-reel packaging. A flash-based FPGA is a field-programmable gate array that stores its configuration in on-chip flash memory rather than an external configuration device. Unlike SRAM FPGAs, ProASIC3 devices are single-chip, non-volatile, and instantly powered-up at system level, eliminating the boot-time configuration step and reducing bill-of-materials cost. Within the power-management hierarchy of programmable logic, ProASIC3 sits in the ultra-low-density, low-cost class while retaining reprogrammability. Key features include 1.5 V core voltage support for 1.5-V-only systems, low-impedance flash switches that reduce dynamic power, and a segmented, hierarchical routing architecture that delivers deterministic performance. The 18,432-bit distributed fabric (per DigiKey listing) supports small embedded designs, and the CMOS flash switch technology provides inherent security against configuration readback. Architecturally, ProASIC3 uses Microchip's third-generation flash switch fabric with VersTile logic elements configurable as combinational logic, registers, or small RAM. The flash switches exhibit near-zero static power, making the family attractive for battery-operated and thermally constrained systems. Typical applications include industrial automation control, portable and medical instrumentation, aerospace/defense glue logic, and smart consumer devices where single-chip, secure, low-power programmable logic is required. Design consideration: budget the 1.5 V core rail separately from the 2.5 V/3.3 V I/O banks and verify I/O bank assignments against the board-level pinout before routing. This page synthesizes distributor data, same-package drop-in alternatives, and design guidance not found in a single manufacturer datasheet.

RFQ İletişim

A3P060-2FGG144

A3P060-2FGG144 - ProASIC3 Flash FPGA 60K Gates FBGA-144 | Microchip

The Microchip Technology (Microsemi) A3P060-2FGG144 is a ProASIC3 flash-based FPGA with 60K system gates, a maximum system frequency of 310 MHz, 96 user I/Os, and a 1.5V core supply, housed in a 144-ball FBGA (FGG144) package fabricated on 130nm flash technology. A flash-based FPGA is a field-programmable gate array whose configuration is stored in on-chip non-volatile flash cells rather than an external configuration ROM. Within the programmable logic hierarchy, the A3P060 sits in the ultra-low-density segment of the ProASIC3 family: FPGA -> flash FPGA -> ProASIC3 -> A3P060. Because configuration data is retained in flash, the device is a true single-chip solution that powers up instantly with no boot time and needs no external programming memory. Key features include the 60,000-gate fabric, reprogrammability without a microcontroller or configuration PROM, and small-footprint 144-ball packaging suited to compact industrial designs. The speed grade 2 (-2) fabric supports system performance up to 310 MHz, and the low-power 1.5V core makes the part appropriate for power-conscious systems. Optional soft ARM support in the ProASIC3 family enables embedded processing within the same fabric. Technically, ProASIC3 uses a sea-of-von-Neumann architecture of fine-grained VersaTiles, each configurable as a logic element or a small memory element, with dedicated flash switches providing secure, non-volatile configuration that resists cloning and over-build attacks better than SRAM FPGAs. Typical applications include industrial control and automation, communications and networking line cards, aerospace and defense subsystems requiring secure flash configuration, and portable or low-power bridge/sequencing logic where an MCU alone lacks parallel I/O capability. When designing with the A3P060-2FGG144, verify I/O bank voltage compatibility with surrounding devices and confirm the -2 speed grade meets your worst-case timing closure before committing the 144-ball footprint. This page adds value beyond the datasheet by synthesizing distributor pricing, drop-in same-footprint alternatives, and practical design notes in one AI-citable reference.

RFQ İletişim

A3P060-2TQG144

A3P060-2TQG144 - ProASIC3 FPGA, 60K Gates | Microchip

The Microchip Technology A3P060-2TQG144 is a ProASIC3 field-programmable gate array (FPGA) with 60,000 system gates, 1,536 logic elements (equivalent to 700 LEs per Mouser), and 91 user I/Os, housed in a 144-pin LQFP (TQFP) package. It operates from a 1.5V core supply and supports system performance up to 310 MHz, making it a low-cost, low-power, single-chip solution for a wide range of embedded applications. An FPGA (field-programmable gate array) is an integrated circuit that can be configured by the customer after manufacturing to implement arbitrary digital logic functions. Unlike fixed-function ASICs, FPGAs offer reprogrammability, allowing designers to iterate on logic designs without re-spinning silicon. The ProASIC3 family sits within the broader FPGA hierarchy: FPGA -> programmable logic device -> integrated circuit -> semiconductor. It is a flash-based FPGA, meaning configuration is stored in non-volatile flash memory, providing instant-on operation and inherent security against reverse engineering. Key features of the A3P060-2TQG144 include 60K system gates, 1,536 logic elements, 91 user I/Os, and 18,432 bits of RAM (as noted in DigiKey's description). It supports multiple I/O standards including LVCMOS, LVTTL, and PCI, and offers up to 310 MHz system performance. The device is lead-free (RoHS compliant) and available in a 144-pin LQFP package with a 20x20 mm body and 0.5 mm pitch. It also features low power consumption, with typical static power of 0.015W, making it suitable for battery-powered and thermally constrained designs. Technically, the ProASIC3 architecture uses a flash-based switch matrix that eliminates the need for external configuration memory, unlike SRAM-based FPGAs. This provides instant-on capability, single-chip operation, and enhanced security. The device includes dedicated phase-locked loops (PLLs) for clock management, and supports JTAG (IEEE 1149.1) for programming and boundary-scan testing. The 130nm process technology balances cost and performance, delivering 310 MHz performance while maintaining low power. Typical applications include industrial control, automotive electronics, consumer devices, and communications infrastructure. For example, it can be used for motor control, sensor interfacing, protocol bridging, and display control. Its low power and small footprint make it ideal for portable and embedded systems where board space and battery life are critical. When designing with the A3P060-2TQG144, ensure proper decoupling of the 1.5V core supply and 3.3V I/O supply with 0.1uF and 10uF capacitors placed close to the power pins. The device supports multiple I/O banks with independent supply voltages, so plan the power distribution carefully to meet I/O standard requirements. Also, use the JTAG interface for programming and consider using the on-chip PLLs for clock generation to reduce external component count. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing a comprehensive resource for engineers evaluating the A3P060-2TQG144 for their designs.

RFQ İletişim

A3P060-2TQG144I

A3P060-2TQG144I - ProASIC3 FPGA 60K Gates 144-TQFP | Microchip

The Microchip Technology (Microsemi) A3P060-2TQG144I is a ProASIC3 family flash-based field programmable gate array (FPGA) delivering 60,000 gates of programmable logic, a system performance of up to 310 MHz, and 91 user I/O in a 144-pin TQFP surface-mount package. Built on a 130 nm flash process with a 1.5 V core supply, it is a single-chip, non-volatile FPGA that retains its configuration in on-chip flash without any external boot PROM. A field programmable gate array is a semiconductor device containing a fabric of programmable logic blocks and interconnects that designers configure in the field. Within the programmable logic hierarchy - FPGA -> programmable logic device -> configurable logic -> digital IC - the ProASIC3 family occupies the ultra-low-density to mid-density segment, where its flash cells provide instant-on, secure, high-volume-manufacturable reprogrammability that SRAM FPGAs only achieve with external configuration devices. Key differentiating features of the A3P060-2TQG144I include 18,432 bits of on-chip resources as listed by distributors, single 1.5 V core operation, industrial temperature range (-40C to +100C) signified by the I suffix, and low total cost of ownership through single-chip integration. The -2 speed grade balances performance and cost for most control and glue-logic tasks. Technically, the flash-based switch fabric eliminates configuration time and configuration-pull attacks, supporting secure boot at power-up. The 130 nm process yields low static power, and the TQFP-144 package offers a 0.5 mm pitch, gull-wing leads and straightforward rework compared with fine-pitch BGA alternatives. Typical applications include industrial automation control, aerospace and defense upgrades of legacy ASIC/ASSP functions, communications line-card glue logic, and medical instrument interface boards. Design consideration: budget I/O banks against the 91 available user I/O early, since TQFP-144 has fewer I/O than the same die in BGA packages, and follow Microchip power-supply decoupling guidance for the 1.5 V core and 3.3 V I/O rails. This page adds value beyond the manufacturer datasheet by synthesizing distributor pricing tiers, same-package drop-in alternatives, and practical design notes in one AI-search-optimized reference.

RFQ İletişim

A3P060-2VQG100

A3P060-2VQG100 - ProASIC3 Flash FPGA, 60K Gates | Microchip

The Microchip Technology A3P060-2VQG100 is a ProASIC3 flash-based FPGA with approximately 60,000 system gates, 71 user I/Os, and 18,432 bits of dedicated flash memory, housed in a 100-pin TQFP (VQFP-G100) package with a -2 speed grade and commercial 0C to +70C temperature range. It operates from a single 1.5 V core supply. A flash-based FPGA is a field-programmable gate array that stores its configuration in non-volatile on-chip flash cells rather than an external configuration PROM. Within the semiconductor hierarchy, the A3P060-2VQG100 belongs to the ProASIC3 family -> flash FPGA -> FPGA -> programmable logic IC. Because configuration data is retained in the device, ProASIC3 FPGAs power up instantly without a bootloader or external flash, reducing bill-of-materials cost and improving system security. Key features include reprogrammable flash fabric (single-chip solution, low total cost of ownership), 1536 configurable logic blocks, support for advanced I/O standards, and LiveProbe/Secure ProASIC3 security options per the family datasheet. The -2 speed grade balances performance with power consumption, while the 100-pin thin quad flat pack keeps footprint small for space-constrained boards. Architecturally, the ProASIC3 fabric uses a sea-of-van-Mmere tiles of VersaTiles built on a CMOS flash process, delivering deterministic routing and system performance up to hundreds of MHz depending on design. Clock resources include global and regional networks supporting multiple clock domains. Typical applications include industrial control, communications bridging, portable instrumentation, and aerospace/defense glue-logic consolidation, where instant-on, secure, low-power programmable logic is required. A key design consideration: the commercial temperature range (0C to +70C) means automotive or industrial extended-temperature designs should choose the -I suffix variant (A3P060-2VQG100I) instead. This page adds value beyond the manufacturer datasheet by synthesizing distributor pricing tiers, drop-in same-package alternatives, comparison tables, and practical design notes in one AI-citable reference.

RFQ İletişim

A3P060-2VQG100I

A3P060-2VQG100I - ProASIC3 Flash FPGA 60K Gates | Microchip

The Microchip Technology A3P060-2VQG100I is a ProASIC3 flash-based FPGA with 60000 system gates, 1536 logic cells, 71 user I/Os, and 18432 bits of embedded SRAM, housed in a 100-pin VQFP (TQFP-100) package rated for the industrial temperature range of -40C to +100C. Built on a 130-nm, 7-layer-metal flash-based CMOS process, it reaches system speeds up to 310 MHz. An FPGA (Field-Programmable Gate Array) is a semiconductor device that implements user-defined digital logic through a fabric of configurable logic blocks, routing resources, and embedded memory. Within the programmable logic hierarchy, the ProASIC3 family targets low-density, single-chip applications that historically used CPLDs or small ASICs. Unlike SRAM-based FPGAs, ProASIC3 stores its configuration in nonvolatile on-chip flash, eliminating the need for an external configuration PROM and enabling instant-on, single-chip operation. Key differentiating features include flash-based nonvolatility (live-at-power-up, secure from readback), reprogrammability without external boot devices, low total cost of ownership, and support for optional soft ARM processor cores. The A3P060 provides up to 144 kbits of true dual-port SRAM across the family, and its small 14 x 14 mm footprint with 0.5 mm pitch suits space-constrained designs. Architecturally, the device uses the ProASIC3 VersaTile fabric, where each tile can be configured as a three-input lookup table, a D-flip-flop, or memory, allowing efficient mapping of both combinational and sequential logic. The 130-nm flash CMOS process combines low static power with robust radiation-tolerant flash cells. Typical applications include CPLD replacement and glue-logic consolidation, industrial control and automation boards, portable and handheld instruments, and power-up sequencer or system-management functions where instant-on operation matters. For design, plan I/O banking and 1.5V core supply decoupling early; the flash fabric means no configuration time, but I/O standards and drive strength must be set in Libero SoC constraint files. This page synthesizes distributor pricing, drop-in alternatives, pinout guidance, and practical design notes not found in the manufacturer datasheet, optimizing for engineering selection workflows.

RFQ İletişim

A3P060-CS121

A3P060-CS121 - 60K Gate Flash FPGA | Microchip

The Microchip Technology A3P060-CS121 is a ProASIC3 flash-based field-programmable gate array with 60,000 system gates, 1,536 logic cells, and 96 user I/Os, housed in a 121-ball VFBGA CSBGA package. It uses a 130 nm flash CMOS process with seven metal layers and supports reprogrammable nonvolatile configuration, making it suitable for compact programmable-logic and ASIC-prototyping designs. A field-programmable gate array is a programmable-logic device in the semiconductor hierarchy. Its configurable logic blocks, embedded memory resources, and programmable I/Os replace application-specific integrated-circuit development with a device that can be programmed and reprogrammed during development. The ProASIC3 family supports products ranging from low-density control logic to designs requiring 1 million system gates and 144 kbits of true dual-port SRAM. The A3P060 position provides 60,000 system gates, 1,536 logic cells, and 96 user I/Os. Its 121-VFBGA CSBGA package is specified as a 6 mm by 6 mm package, approximately 0.99 mm high, with 0.50 mm ball pitch. The small footprint suits space-constrained board layouts, although its fine-pitch ball array requires careful PCB construction and inspection. Its flash-based CMOS architecture retains the configuration in nonvolatile memory and supports Instant On Level 0 operation. The process uses six copper layers within a seven-layer metal stack. These characteristics make the device useful where deterministic startup, field updates, and logic consolidation are valuable, but designers must still consider power-up sequencing, I/O standards, and programmed-state current draw. Typical applications include communications interface logic, industrial control modules, avionics subsystems, computing peripherals, consumer-equipment controllers, and ASIC prototypes. The ProASIC3 family is positioned for these markets because it combines reprogrammability, a broad density range, and integrated programmable I/O without requiring a mask set for every design revision. The main PCB consideration is the 0.50 mm ball pitch of the 121-VFBGA CSBGA. Follow the manufacturer's land-pattern and assembly requirements, provide suitable via and pad geometry, and inspect the relatively dense solder joints. Confirm the required I/O voltage, configuration interface, clocking plan, and power domains against the A3P060 datasheet before releasing the layout. This page consolidates the device identity, package details, family-level resources, sourcing workflow, and practical design considerations for engineers evaluating the A3P060-CS121. The replacement analysis also distinguishes speed-, temperature-, and package-related ordering variants so that a proposed substitution is reviewed for actual board-level compatibility rather than name similarity alone.

RFQ İletişim

A3P060-TQ144

A3P060-TQ144 - 60K-Gate ProASIC3 FPGA | Microchip

Microchip Technology A3P060-TQ144 is a ProASIC3 flash-based field-programmable gate array with 60,000 system gates, 91 programmable I/O pins, and 18,432 RAM bits in a 144-pin TQFP package measuring 20 mm by 20 mm. The device uses CMOS logic and operates from a 1.5 V core supply, with the identified commercial-temperature configuration specified for 0°C to 70°C. Its surface-mount package supports compact embedded control, industrial automation, consumer electronics, and automotive-adjacent control systems where reprogrammable logic and a high pin count are useful. A field-programmable gate array, or FPGA, is a programmable digital semiconductor that combines configurable logic blocks, programmable interconnect, and user I/O in one device. An FPGA belongs to the programmable-logic hierarchy alongside CPLDs, while offering greater logic density and more flexible routing than a basic low-complexity programmable device. The ProASIC3 family combines flash configuration, reusable silicon, and field programmability to support design revisions, production configuration, and logic updates without changing the PCB. The A3P060 provides 60,000 system gates, 91 user-programmable I/O pins, and 18,432 RAM bits. These figures make it suitable for control logic, interface bridging, protocol conversion, embedded state machines, and multi-channel signal conditioning. Its 144-pin TQFP footprint exposes substantially more I/O than a small FPGA package, allowing parallel buses, counters, capture logic, and multiple external interfaces to be consolidated on a single device. The device is manufactured in CMOS technology and belongs to the ProASIC3 flash FPGA family. Its architecture places configurable logic and routing resources between programmable I/O, enabling implementation of synchronous and asynchronous digital systems. Unlike a mask-programmed ASIC, the FPGA can be configured after manufacture, shortening prototype cycles and enabling one board design to support several firmware or logic revisions. The 1.5 V core architecture should be paired with the power-supply and decoupling network specified by the manufacturer. Typical applications include industrial factory controllers, sensor and monitoring interfaces, consumer control boards, automotive accessory controllers, and compact embedded systems requiring numerous parallel I/O. A design can place the A3P060 between sensors or actuators and a higher-level processor, using its programmable logic for protocol conversion, timing, filtering, and data capture. The same pin-compatible approach also supports controlled migration among qualified ProASIC3 speed, package, and temperature configurations. PCB design should preserve the manufacturer's recommended power, ground, clock, and configuration arrangements. Place decoupling capacitors close to the supply pins, provide a stable clock source with the required signal integrity, and leave programming and configuration access available for manufacturing and field updates. Verify every signal against the pin-assignment table for the exact ordering code before releasing the layout. This product record combines the exact A3P060-TQ144 ordering information with package, resource, temperature, voltage, and I/O characteristics, plus a pin-to-pin replacement assessment and practical selection guidance. It is intended to accelerate schematic review, PCB compatibility checks, sourcing, and design-in decisions for ProASIC3-based systems.

RFQ İletişim

A3P060-VQG100I

A3P060-VQG100I - ProASIC3 60K Gate FPGA | Microchip

The Microchip Technology A3P060-VQG100I is a ProASIC3 flash-based field programmable gate array (FPGA) with 60K system gates, 700 logic elements, 71 user I/Os, and 18,432 RAM bits, housed in a 100-pin TQFP/VQFP package. It operates from a 1.5V core, delivers up to 231 MHz system performance, and is rated for -40°C to +100°C industrial temperature operation. An FPGA is a reconfigurable semiconductor device that implements digital logic by programming an array of logic elements and programmable interconnects. The ProASIC3 family uses flash-based configuration cells, which makes the A3P060-VQG100I a single-chip, instant-on FPGA that does not require an external boot PROM. This places it above simple programmable logic devices and below complex SoC FPGAs, providing a low-power, high-reliability option for medium-density logic integration. Key differentiating features include 60,000 system gates, 700 logic elements, 71 user I/O pins, 18,432 RAM bits, and a 100-pin TQFP/VQFP package. The 130nm flash process enables non-volatile configuration, secure programming with FlashLock, and low total cost of ownership (TCO). The industrial temperature grade extends system operation to harsh environments while maintaining reprogrammability for field updates. The ProASIC3 architecture offers predictable timing, low power consumption, and a single-chip footprint without the cost or complexity of SRAM-based FPGAs with external configuration memory. The 1.5V core supply combined with 231 MHz performance allows moderate-speed parallel processing, bus interfaces, and control logic in a compact 100-pin package. Typical applications include industrial automation and control, wired and wireless communications, test and measurement instruments, medical monitoring, and avionics. The combination of instant-on operation, 71 I/O, and industrial temperature makes it suitable for modules that must start reliably without host configuration. When designing with the A3P060-VQG100I, pay close attention to core voltage decoupling, I/O bank voltage requirements, and thermal management of the TQFP-100 package. Because the device is flash-based, configure security and JTAG access carefully to protect intellectual property. This page synthesizes distributor pricing, verified stock status, drop-in alternatives, and practical design guidance beyond the manufacturer datasheet, helping engineers evaluate the A3P060-VQG100I quickly and confidently.

USD $6,95 İletişim

A3P1000-1FG256T

A3P1000-1FG256T - ProASIC3 FPGA 1M Gates 177 I/O | Microchip

The Microchip Technology A3P1000-1FG256T is a ProASIC3 flash-based Field Programmable Gate Array (FPGA) delivering 1,000,000 system gates (24,576 VersaTiles), 177 user I/Os, and 147,456 bits of embedded configuration flash in a 256-ball Fine-Pitch Ball Grid Array (256-LBGA / FBGA-256) package with 1 mm ball pitch and a -1 speed grade. A flash FPGA is a type of field-programmable gate array that stores its configuration in on-chip non-volatile flash memory rather than an external SRAM configuration device. Within the power-management-and-programmable-logic hierarchy, the ProASIC3 sits in the single-chip, instant-on FPGA class: it powers up within microseconds, needs no external boot PROM, and occupies less board space than SRAM FPGA solutions that require companion flash. Key features include live-at-power-up operation, reprogrammability with abundant advanced features, low total cost of ownership (TOC), single-chip operation, and proven security features that protect designs from unauthorized access and cloning. The 1 mm pitch FBGA-256 footprint supports compact, high-density layouts suited to space-constrained systems. Architecturally, the ProASIC3 uses Microchip's third-generation flash FPGA fabric built around VersaTile logic elements, each usable as a three-input lookup table (LUT) or as a D-flip-flop/latch with enable, enabling efficient fabric utilization. Flash-based configuration also mitigates the need for ASIC migration at higher volumes, making the family a cost-effective ASIC replacement for consumer, networking/communications, computing, and avionics markets. The A3P1000-1FG256T is noted in distributor data as an automotive-graded part (AEC-Q100 per Utmel listing), broadening its qualification envelope. Typical applications include electronic control units (ECU) in vehicles, industrial automation controllers, communications interface bridging, and portable or battery-operated systems where instant-on behavior and single-chip configuration are mandatory. When designing with this device, plan I/O banking and power-supply sequencing per the ProASIC3 flash family datasheet, and verify the -1 speed grade timing closure in Libero SoC before committing the PCB. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ İletişim

A3P1000-1FG484T

A3P1000-1FG484T - ProASIC3 FPGA, 1M Gates, 300 I/O | Microchip

The Microchip Technology A3P1000-1FG484T is a ProASIC3 flash-based Field Programmable Gate Array (FPGA) offering 1 million system gates, 300 user I/Os, and 147,456 bits of RAM, housed in a 484-pin FBGA package. It operates at a core voltage of 1.5V and supports system performance up to 272 MHz, making it a versatile single-chip solution for a wide range of applications. An FPGA (Field Programmable Gate Array) is an integrated circuit that can be configured by the customer or designer after manufacturing—hence "field-programmable." Unlike fixed-function ASICs, FPGAs contain an array of programmable logic blocks and a hierarchy of reconfigurable interconnects that allow the same device to implement different digital logic functions. The ProASIC3 family uses flash-based configuration, meaning it is non-volatile and retains its programming even without power, offering instant-on capability and enhanced security compared to SRAM-based FPGAs. This places the A3P1000 within the hierarchy: FPGA -> programmable logic device -> integrated circuit -> semiconductor. Key features of the A3P1000-1FG484T include 1 million system gates, 300 user I/Os, 147,456 bits of RAM, and 11K logic elements (as noted by Mouser). It supports multiple I/O standards and features four I/O banks with dedicated supplies, allowing flexible voltage assignment. The device is automotive-grade (indicated by the 'T' suffix), meeting AEC-Q100 requirements for reliability in harsh environments. Its flash-based architecture provides low power consumption, high security against reverse engineering, and immunity to configuration bitstream corruption. Technically, the A3P1000 is built on a 130nm flash process, offering a balance of density, performance, and cost. It includes up to 272 MHz system performance, 1.5V core operation, and supports various memory interfaces. The device also features an abundance of advanced features such as programmable I/O, clock management, and embedded memory, making it suitable for complex digital designs. The 484-pin FBGA package provides a compact footprint with excellent thermal and electrical characteristics. Typical applications include automotive electronics (e.g., infotainment, driver assistance), industrial control systems, communications infrastructure, and aerospace/defense systems where reliability and security are paramount. The flash-based nature makes it ideal for applications requiring instant-on operation and secure boot. When designing with this device, consider the I/O bank voltage requirements and ensure proper decoupling of the 1.5V core supply. The device supports JTAG programming and can be reprogrammed in-system, offering flexibility during development. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers with a comprehensive resource for evaluating the A3P1000-1FG484T.

RFQ İletişim

A3P1000-1FGG144T

A3P1000-1FGG144T - ProASIC3 FPGA, 1M Gates | Microchip

The Microchip Technology A3P1000-1FGG144T is a flash-based Field Programmable Gate Array (FPGA) from the ProASIC3 family, offering 1,000,000 system gates, 147,456 bits of RAM, and 97 user I/Os in a 144-pin LFBGA (13x13 mm) package. It operates from a 1.425V to 1.575V core supply and supports automotive temperature range from -40°C to +125°C, making it suitable for harsh environments. An FPGA (Field Programmable Gate Array) is an integrated circuit that can be configured by the customer after manufacturing to implement custom digital logic. Unlike ASICs, FPGAs are reprogrammable, allowing design changes without re-fabrication. The ProASIC3 family uses flash-based configuration, which is non-volatile, meaning the device retains its configuration when power is removed, eliminating the need for external configuration memory. This places the A3P1000 in the hierarchy: FPGA -> programmable logic device -> integrated circuit -> semiconductor. Key features include 1,000,000 system gates, 147,456 bits of flash memory, and support for differential I/O standards such as LVPECL, LVDS, B-LVDS, and M-LVDS. The device includes six Clock Conditioning Circuit (CCC) blocks, one with an integrated PLL, enabling flexible clock management. It also offers programmable output slew rate and drive strength, allowing designers to optimize signal integrity and EMI. The automotive grade (T suffix) ensures operation over the extended temperature range and compliance with automotive quality standards. Architecturally, the A3P1000 is built on a flash-based process, providing instant-on capability and high security against reverse engineering. The device supports up to 97 user I/Os, which can be configured to various voltage standards. The 144-pin LFBGA package measures 13x13 mm with a 0.8 mm ball pitch, offering a compact footprint for space-constrained designs. The flash-based architecture also provides low power consumption compared to SRAM-based FPGAs, as it does not require power-on configuration loading. Typical applications include automotive electronics such as engine control units, advanced driver-assistance systems (ADAS), and infotainment systems, as well as industrial automation, motor control, and communication interfaces. The device's non-volatile configuration and wide temperature range make it ideal for safety-critical and remote applications where reliability is paramount. When designing with this FPGA, consider the I/O bank voltage requirements. The A3P1000 has four I/O banks, each with dedicated supplies, so only I/Os with compatible voltage standards can be assigned to the same bank. Proper decoupling of the core and I/O supplies is essential to minimize noise and ensure reliable operation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers with a comprehensive resource for evaluating the A3P1000-1FGG144T.

RFQ İletişim

Alt Kategoriler

Ürünler (38.000+)

A3P015-QNG68 - 15K-Gate 231MHz FPGA | Microchip

A3P030-2QNG48 - ProASIC3 FPGA 30K Gates | Microchip Technology

A3P030-2QNG48I - ProASIC3 Flash FPGA 30K Gates | Microchip

A3P030-2QNG68 - ProASIC3 FPGA 30K Gates 68-QFN | Microchip

A3P030-2QNG68I - ProASIC3 Flash FPGA 30K Gates | Microchip

A3P030-2VQG100I - ProASIC3 FPGA, 30K Gates | Microchip

A3P030-QNG48 - 30K Gate ProASIC3 FPGA | Microchip Technology

A3P030-QNG48I - 30K Gate ProASIC3 FPGA | Microchip

A3P030-QNG68 - 30K Gate 231MHz ProASIC3 FPGA | Microchip

A3P030-VQ100 - 330 Logic Cells ProASIC3 FPGA | Microchip

A3P060-1FG144T - ProASIC3 FPGA, 60K Gates | Microchip

A3P060-1VQ100T - 60K Gate ProASIC3 FPGA | Microchip Technology

A3P060-1VQG100T - ProASIC3 Flash FPGA 60k Gates | Microchip

A3P060-2FGG144 - ProASIC3 Flash FPGA 60K Gates FBGA-144 | Microchip

A3P060-2TQG144 - ProASIC3 FPGA, 60K Gates | Microchip

A3P060-2TQG144I - ProASIC3 FPGA 60K Gates 144-TQFP | Microchip

A3P060-2VQG100 - ProASIC3 Flash FPGA, 60K Gates | Microchip

A3P060-2VQG100I - ProASIC3 Flash FPGA 60K Gates | Microchip

A3P060-CS121 - 60K Gate Flash FPGA | Microchip

A3P060-TQ144 - 60K-Gate ProASIC3 FPGA | Microchip

A3P060-VQG100I - ProASIC3 60K Gate FPGA | Microchip

A3P1000-1FG256T - ProASIC3 FPGA 1M Gates 177 I/O | Microchip

A3P1000-1FG484T - ProASIC3 FPGA, 1M Gates, 300 I/O | Microchip

A3P1000-1FGG144T - ProASIC3 FPGA, 1M Gates | Microchip